linux-input.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* [PATCH v6 00/11] Raspberry Pi PoE HAT fan support
@ 2020-12-11 16:47 Nicolas Saenz Julienne
  2020-12-11 16:47 ` [PATCH v6 01/11] firmware: raspberrypi: Keep count of all consumers Nicolas Saenz Julienne
                   ` (11 more replies)
  0 siblings, 12 replies; 22+ messages in thread
From: Nicolas Saenz Julienne @ 2020-12-11 16:47 UTC (permalink / raw)
  To: u.kleine-koenig, linux-kernel
  Cc: f.fainelli, linux-pwm, bcm-kernel-feedback-list,
	linux-arm-kernel, devicetree, wahrenst, linux-input,
	dmitry.torokhov, gregkh, devel, p.zabel, linux-gpio,
	linus.walleij, linux-clk, sboyd, linux-rpi-kernel, bgolaszewski,
	andy.shevchenko, Nicolas Saenz Julienne, Eric Anholt

The aim of this series is to add support to the fan found on RPi's PoE
HAT. Some commentary on the design can be found below. But the imporant
part to the people CC'd here not involved with PWM is that, in order to
achieve this properly, we also have to fix the firmware interface the
driver uses to communicate with the PWM bus (and many other low level
functions). Specifically, we have to make sure the firmware interface
isn't unbound while consumers are still up. So, patch #1 & #2 introduce
reference counting in the firwmware interface driver and patches #3 to
#8 update all firmware users. Patches #9 to #11 introduce the new PWM
driver.

I sent everything as a single series as the final version of the PWM
drivers depends on the firwmare fixes, but I'll be happy to split this
into two separate series if you think it's better.

--- Original cover letter below ---

This series aims at adding support to RPi's official PoE HAT fan[1].

The HW setup is the following:

| Raspberry Pi                               | PoE HAT                    |
 arm core -> Mailbox -> RPi co-processor -> I2C -> Atmel MCU -> PWM -> FAN

The arm cores have only access to the mailbox interface, as i2c0, even if
physically accessible, is to be used solely by the co-processor
(VideoCore 4/6).

This series implements a PWM bus, and has pwm-fan sitting on top of it as per
this discussion: https://lkml.org/lkml/2018/9/2/486. Although this design has a
series of shortcomings:

- It depends on a DT binding: it's not flexible if a new hat shows up with new
  functionality, we're not 100% sure we'll be able to expand it without
  breaking backwards compatibility. But without it we can't make use of DT
  thermal-zones, which IMO is overkill.

- We're using pwm-fan, writing a hwmon driver would, again, give us more
  flexibility, but it's not really needed at the moment.

I personally think that it's not worth the effort, it's unlikely we'll get
things right in advance. And ultimately, if the RPi people come up with
something new, we can always write a new driver/bindings from scratch (as in
not reusing previous code).

That said, I'm more than happy to change things if there is a consensus that
another design will do the trick.

[1] https://www.raspberrypi.org/blog/introducing-power-over-ethernet-poe-hat/

---

Changes since v5:
 - Small cleanups
 - Add extra code comments

Changes since v4:
 - Cleanup devm calls
 - Rename compatible string so it's unique to the PoE HAT

Changes since v3:
 - Split first patch, #1 introduces refcount, then #2 the devm function
 - Fix touchscreen function
 - Use kref

Changes since v2:
 - Introduce devm_rpi_firmware_get()
 - Small cleanups in PWM driver

Changes since v1:
 - Address PWM driver changes
 - Fix binding, now with 2 cells

Nicolas Saenz Julienne (11):
  firmware: raspberrypi: Keep count of all consumers
  firmware: raspberrypi: Introduce devm_rpi_firmware_get()
  clk: bcm: rpi: Release firmware handle on unbind
  gpio: raspberrypi-exp: Release firmware handle on unbind
  reset: raspberrypi: Release firmware handle on unbind
  soc: bcm: raspberrypi-power: Release firmware handle on unbind
  staging: vchiq: Release firmware handle on unbind
  input: raspberrypi-ts: Release firmware handle when not needed
  dt-bindings: pwm: Add binding for RPi firmware PWM bus
  DO NOT MERGE: ARM: dts: Add RPi's official PoE hat support
  pwm: Add Raspberry Pi Firmware based PWM bus

 .../arm/bcm/raspberrypi,bcm2835-firmware.yaml |  20 ++
 arch/arm/boot/dts/bcm2711-rpi-4-b.dts         |  54 +++++
 drivers/clk/bcm/clk-raspberrypi.c             |   2 +-
 drivers/firmware/raspberrypi.c                |  69 +++++-
 drivers/gpio/gpio-raspberrypi-exp.c           |   2 +-
 drivers/input/touchscreen/raspberrypi-ts.c    |   2 +-
 drivers/pwm/Kconfig                           |   9 +
 drivers/pwm/Makefile                          |   1 +
 drivers/pwm/pwm-raspberrypi-poe.c             | 216 ++++++++++++++++++
 drivers/reset/reset-raspberrypi.c             |   2 +-
 drivers/soc/bcm/raspberrypi-power.c           |   2 +-
 .../interface/vchiq_arm/vchiq_arm.c           |   2 +-
 .../pwm/raspberrypi,firmware-poe-pwm.h        |  13 ++
 include/soc/bcm2835/raspberrypi-firmware.h    |  10 +
 14 files changed, 395 insertions(+), 9 deletions(-)
 create mode 100644 drivers/pwm/pwm-raspberrypi-poe.c
 create mode 100644 include/dt-bindings/pwm/raspberrypi,firmware-poe-pwm.h

-- 
2.29.2


^ permalink raw reply	[flat|nested] 22+ messages in thread

* [PATCH v6 01/11] firmware: raspberrypi: Keep count of all consumers
  2020-12-11 16:47 [PATCH v6 00/11] Raspberry Pi PoE HAT fan support Nicolas Saenz Julienne
@ 2020-12-11 16:47 ` Nicolas Saenz Julienne
  2020-12-13  5:14   ` Stephen Boyd
  2020-12-16 10:37   ` Bartosz Golaszewski
  2020-12-11 16:47 ` [PATCH v6 02/11] firmware: raspberrypi: Introduce devm_rpi_firmware_get() Nicolas Saenz Julienne
                   ` (10 subsequent siblings)
  11 siblings, 2 replies; 22+ messages in thread
From: Nicolas Saenz Julienne @ 2020-12-11 16:47 UTC (permalink / raw)
  To: u.kleine-koenig, linux-kernel, Nicolas Saenz Julienne,
	Florian Fainelli, Ray Jui, Scott Branden,
	bcm-kernel-feedback-list
  Cc: linux-pwm, linux-arm-kernel, devicetree, wahrenst, linux-input,
	dmitry.torokhov, gregkh, devel, p.zabel, linux-gpio,
	linus.walleij, linux-clk, sboyd, linux-rpi-kernel, bgolaszewski,
	andy.shevchenko

When unbinding the firmware device we need to make sure it has no
consumers left. Otherwise we'd leave them with a firmware handle
pointing at freed memory.

Keep a reference count of all consumers and introduce rpi_firmware_put()
which will permit automatically decrease the reference count upon
unbinding consumer drivers.

Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>

---
Changes since v5:
 - Add comment to avoid people blindly switching the memory allocation
   to the devm variant.
 - Fix function documentation as per Florian's comment.

 Changes since v3:
- Use kref instead of waiting on refcount

 drivers/firmware/raspberrypi.c             | 40 ++++++++++++++++++++--
 include/soc/bcm2835/raspberrypi-firmware.h |  2 ++
 2 files changed, 39 insertions(+), 3 deletions(-)

diff --git a/drivers/firmware/raspberrypi.c b/drivers/firmware/raspberrypi.c
index 30259dc9b805..b65e4c495772 100644
--- a/drivers/firmware/raspberrypi.c
+++ b/drivers/firmware/raspberrypi.c
@@ -7,6 +7,7 @@
  */
 
 #include <linux/dma-mapping.h>
+#include <linux/kref.h>
 #include <linux/mailbox_client.h>
 #include <linux/module.h>
 #include <linux/of_platform.h>
@@ -27,6 +28,8 @@ struct rpi_firmware {
 	struct mbox_chan *chan; /* The property channel. */
 	struct completion c;
 	u32 enabled;
+
+	struct kref consumers;
 };
 
 static DEFINE_MUTEX(transaction_lock);
@@ -225,12 +228,31 @@ static void rpi_register_clk_driver(struct device *dev)
 						-1, NULL, 0);
 }
 
+static void rpi_firmware_delete(struct kref *kref)
+{
+	struct rpi_firmware *fw = container_of(kref, struct rpi_firmware,
+					       consumers);
+
+	mbox_free_channel(fw->chan);
+	kfree(fw);
+}
+
+void rpi_firmware_put(struct rpi_firmware *fw)
+{
+	kref_put(&fw->consumers, rpi_firmware_delete);
+}
+EXPORT_SYMBOL_GPL(rpi_firmware_put);
+
 static int rpi_firmware_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct rpi_firmware *fw;
 
-	fw = devm_kzalloc(dev, sizeof(*fw), GFP_KERNEL);
+	/*
+	 * Memory will be freed by rpi_firmware_delete() once all users have
+	 * released their firmware handles. Don't use devm_kzalloc() here.
+	 */
+	fw = kzalloc(sizeof(*fw), GFP_KERNEL);
 	if (!fw)
 		return -ENOMEM;
 
@@ -247,6 +269,7 @@ static int rpi_firmware_probe(struct platform_device *pdev)
 	}
 
 	init_completion(&fw->c);
+	kref_init(&fw->consumers);
 
 	platform_set_drvdata(pdev, fw);
 
@@ -275,7 +298,8 @@ static int rpi_firmware_remove(struct platform_device *pdev)
 	rpi_hwmon = NULL;
 	platform_device_unregister(rpi_clk);
 	rpi_clk = NULL;
-	mbox_free_channel(fw->chan);
+
+	rpi_firmware_put(fw);
 
 	return 0;
 }
@@ -284,16 +308,26 @@ static int rpi_firmware_remove(struct platform_device *pdev)
  * rpi_firmware_get - Get pointer to rpi_firmware structure.
  * @firmware_node:    Pointer to the firmware Device Tree node.
  *
+ * The reference to rpi_firmware has to be released with rpi_firmware_put().
+ *
  * Returns NULL is the firmware device is not ready.
  */
 struct rpi_firmware *rpi_firmware_get(struct device_node *firmware_node)
 {
 	struct platform_device *pdev = of_find_device_by_node(firmware_node);
+	struct rpi_firmware *fw;
 
 	if (!pdev)
 		return NULL;
 
-	return platform_get_drvdata(pdev);
+	fw = platform_get_drvdata(pdev);
+	if (!fw)
+		return NULL;
+
+	if (!kref_get_unless_zero(&fw->consumers))
+		return NULL;
+
+	return fw;
 }
 EXPORT_SYMBOL_GPL(rpi_firmware_get);
 
diff --git a/include/soc/bcm2835/raspberrypi-firmware.h b/include/soc/bcm2835/raspberrypi-firmware.h
index cc9cdbc66403..fdfef7fe40df 100644
--- a/include/soc/bcm2835/raspberrypi-firmware.h
+++ b/include/soc/bcm2835/raspberrypi-firmware.h
@@ -140,6 +140,7 @@ int rpi_firmware_property(struct rpi_firmware *fw,
 			  u32 tag, void *data, size_t len);
 int rpi_firmware_property_list(struct rpi_firmware *fw,
 			       void *data, size_t tag_size);
+void rpi_firmware_put(struct rpi_firmware *fw);
 struct rpi_firmware *rpi_firmware_get(struct device_node *firmware_node);
 #else
 static inline int rpi_firmware_property(struct rpi_firmware *fw, u32 tag,
@@ -154,6 +155,7 @@ static inline int rpi_firmware_property_list(struct rpi_firmware *fw,
 	return -ENOSYS;
 }
 
+static inline void rpi_firmware_put(struct rpi_firmware *fw) { }
 static inline struct rpi_firmware *rpi_firmware_get(struct device_node *firmware_node)
 {
 	return NULL;
-- 
2.29.2


^ permalink raw reply	[flat|nested] 22+ messages in thread

* [PATCH v6 02/11] firmware: raspberrypi: Introduce devm_rpi_firmware_get()
  2020-12-11 16:47 [PATCH v6 00/11] Raspberry Pi PoE HAT fan support Nicolas Saenz Julienne
  2020-12-11 16:47 ` [PATCH v6 01/11] firmware: raspberrypi: Keep count of all consumers Nicolas Saenz Julienne
@ 2020-12-11 16:47 ` Nicolas Saenz Julienne
  2020-12-16 10:35   ` Bartosz Golaszewski
  2020-12-11 16:47 ` [PATCH v6 03/11] clk: bcm: rpi: Release firmware handle on unbind Nicolas Saenz Julienne
                   ` (9 subsequent siblings)
  11 siblings, 1 reply; 22+ messages in thread
From: Nicolas Saenz Julienne @ 2020-12-11 16:47 UTC (permalink / raw)
  To: u.kleine-koenig, linux-kernel, Florian Fainelli, Ray Jui,
	Scott Branden, bcm-kernel-feedback-list, Nicolas Saenz Julienne
  Cc: linux-pwm, linux-arm-kernel, devicetree, wahrenst, linux-input,
	dmitry.torokhov, gregkh, devel, p.zabel, linux-gpio,
	linus.walleij, linux-clk, sboyd, linux-rpi-kernel, bgolaszewski,
	andy.shevchenko

It'll simplify the firmware handling for most consumers.

Suggested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
---

Changes since v4:
 - Rearrange function calls for clarity, same functionality

Changes since v2:
- Create devm_rpi_firmware_get()

 drivers/firmware/raspberrypi.c             | 29 ++++++++++++++++++++++
 include/soc/bcm2835/raspberrypi-firmware.h |  8 ++++++
 2 files changed, 37 insertions(+)

diff --git a/drivers/firmware/raspberrypi.c b/drivers/firmware/raspberrypi.c
index b65e4c495772..250e01680742 100644
--- a/drivers/firmware/raspberrypi.c
+++ b/drivers/firmware/raspberrypi.c
@@ -243,6 +243,13 @@ void rpi_firmware_put(struct rpi_firmware *fw)
 }
 EXPORT_SYMBOL_GPL(rpi_firmware_put);
 
+static void devm_rpi_firmware_put(void *data)
+{
+	struct rpi_firmware *fw = data;
+
+	rpi_firmware_put(fw);
+}
+
 static int rpi_firmware_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -331,6 +338,28 @@ struct rpi_firmware *rpi_firmware_get(struct device_node *firmware_node)
 }
 EXPORT_SYMBOL_GPL(rpi_firmware_get);
 
+/**
+ * devm_rpi_firmware_get - Get pointer to rpi_firmware structure.
+ * @firmware_node:    Pointer to the firmware Device Tree node.
+ *
+ * Returns NULL is the firmware device is not ready.
+ */
+struct rpi_firmware *devm_rpi_firmware_get(struct device *dev,
+					   struct device_node *firmware_node)
+{
+	struct rpi_firmware *fw;
+
+	fw = rpi_firmware_get(firmware_node);
+	if (!fw)
+		return NULL;
+
+	if (devm_add_action_or_reset(dev, devm_rpi_firmware_put, fw))
+		return NULL;
+
+	return fw;
+}
+EXPORT_SYMBOL_GPL(devm_rpi_firmware_get);
+
 static const struct of_device_id rpi_firmware_of_match[] = {
 	{ .compatible = "raspberrypi,bcm2835-firmware", },
 	{},
diff --git a/include/soc/bcm2835/raspberrypi-firmware.h b/include/soc/bcm2835/raspberrypi-firmware.h
index fdfef7fe40df..73ad784fca96 100644
--- a/include/soc/bcm2835/raspberrypi-firmware.h
+++ b/include/soc/bcm2835/raspberrypi-firmware.h
@@ -142,6 +142,8 @@ int rpi_firmware_property_list(struct rpi_firmware *fw,
 			       void *data, size_t tag_size);
 void rpi_firmware_put(struct rpi_firmware *fw);
 struct rpi_firmware *rpi_firmware_get(struct device_node *firmware_node);
+struct rpi_firmware *devm_rpi_firmware_get(struct device *dev,
+					   struct device_node *firmware_node);
 #else
 static inline int rpi_firmware_property(struct rpi_firmware *fw, u32 tag,
 					void *data, size_t len)
@@ -160,6 +162,12 @@ static inline struct rpi_firmware *rpi_firmware_get(struct device_node *firmware
 {
 	return NULL;
 }
+
+static inline struct rpi_firmware *devm_rpi_firmware_get(struct device *dev,
+					struct device_node *firmware_node)
+{
+	return NULL;
+}
 #endif
 
 #endif /* __SOC_RASPBERRY_FIRMWARE_H__ */
-- 
2.29.2


^ permalink raw reply	[flat|nested] 22+ messages in thread

* [PATCH v6 03/11] clk: bcm: rpi: Release firmware handle on unbind
  2020-12-11 16:47 [PATCH v6 00/11] Raspberry Pi PoE HAT fan support Nicolas Saenz Julienne
  2020-12-11 16:47 ` [PATCH v6 01/11] firmware: raspberrypi: Keep count of all consumers Nicolas Saenz Julienne
  2020-12-11 16:47 ` [PATCH v6 02/11] firmware: raspberrypi: Introduce devm_rpi_firmware_get() Nicolas Saenz Julienne
@ 2020-12-11 16:47 ` Nicolas Saenz Julienne
  2020-12-13  5:12   ` Stephen Boyd
  2020-12-11 16:47 ` [PATCH v6 04/11] gpio: raspberrypi-exp: " Nicolas Saenz Julienne
                   ` (8 subsequent siblings)
  11 siblings, 1 reply; 22+ messages in thread
From: Nicolas Saenz Julienne @ 2020-12-11 16:47 UTC (permalink / raw)
  To: u.kleine-koenig, linux-kernel
  Cc: f.fainelli, linux-pwm, bcm-kernel-feedback-list,
	linux-arm-kernel, devicetree, wahrenst, linux-input,
	dmitry.torokhov, gregkh, devel, p.zabel, linux-gpio,
	linus.walleij, linux-clk, sboyd, linux-rpi-kernel, bgolaszewski,
	andy.shevchenko, Nicolas Saenz Julienne, Michael Turquette

Use devm_rpi_firmware_get() so as to make sure we release RPi's firmware
interface when unbinding the device.

Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
---
 drivers/clk/bcm/clk-raspberrypi.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/clk/bcm/clk-raspberrypi.c b/drivers/clk/bcm/clk-raspberrypi.c
index f89b9cfc4309..dd3b71eafabf 100644
--- a/drivers/clk/bcm/clk-raspberrypi.c
+++ b/drivers/clk/bcm/clk-raspberrypi.c
@@ -314,7 +314,7 @@ static int raspberrypi_clk_probe(struct platform_device *pdev)
 		return -ENOENT;
 	}
 
-	firmware = rpi_firmware_get(firmware_node);
+	firmware = devm_rpi_firmware_get(&pdev->dev, firmware_node);
 	of_node_put(firmware_node);
 	if (!firmware)
 		return -EPROBE_DEFER;
-- 
2.29.2


^ permalink raw reply	[flat|nested] 22+ messages in thread

* [PATCH v6 04/11] gpio: raspberrypi-exp: Release firmware handle on unbind
  2020-12-11 16:47 [PATCH v6 00/11] Raspberry Pi PoE HAT fan support Nicolas Saenz Julienne
                   ` (2 preceding siblings ...)
  2020-12-11 16:47 ` [PATCH v6 03/11] clk: bcm: rpi: Release firmware handle on unbind Nicolas Saenz Julienne
@ 2020-12-11 16:47 ` Nicolas Saenz Julienne
  2020-12-11 16:47 ` [PATCH v6 05/11] reset: raspberrypi: " Nicolas Saenz Julienne
                   ` (7 subsequent siblings)
  11 siblings, 0 replies; 22+ messages in thread
From: Nicolas Saenz Julienne @ 2020-12-11 16:47 UTC (permalink / raw)
  To: u.kleine-koenig, linux-kernel, Linus Walleij, Bartosz Golaszewski
  Cc: f.fainelli, linux-pwm, bcm-kernel-feedback-list,
	linux-arm-kernel, devicetree, wahrenst, linux-input,
	dmitry.torokhov, gregkh, devel, p.zabel, linux-gpio, linux-clk,
	sboyd, linux-rpi-kernel, andy.shevchenko, Nicolas Saenz Julienne

Use devm_rpi_firmware_get() so as to make sure we release RPi's firmware
interface when unbinding the device.

Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
---
 drivers/gpio/gpio-raspberrypi-exp.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/gpio/gpio-raspberrypi-exp.c b/drivers/gpio/gpio-raspberrypi-exp.c
index bb100e0124e6..64a552ecc2ad 100644
--- a/drivers/gpio/gpio-raspberrypi-exp.c
+++ b/drivers/gpio/gpio-raspberrypi-exp.c
@@ -208,7 +208,7 @@ static int rpi_exp_gpio_probe(struct platform_device *pdev)
 		return -ENOENT;
 	}
 
-	fw = rpi_firmware_get(fw_node);
+	fw = devm_rpi_firmware_get(&pdev->dev, fw_node);
 	of_node_put(fw_node);
 	if (!fw)
 		return -EPROBE_DEFER;
-- 
2.29.2


^ permalink raw reply	[flat|nested] 22+ messages in thread

* [PATCH v6 05/11] reset: raspberrypi: Release firmware handle on unbind
  2020-12-11 16:47 [PATCH v6 00/11] Raspberry Pi PoE HAT fan support Nicolas Saenz Julienne
                   ` (3 preceding siblings ...)
  2020-12-11 16:47 ` [PATCH v6 04/11] gpio: raspberrypi-exp: " Nicolas Saenz Julienne
@ 2020-12-11 16:47 ` Nicolas Saenz Julienne
  2020-12-11 16:47 ` [PATCH v6 06/11] soc: bcm: raspberrypi-power: " Nicolas Saenz Julienne
                   ` (6 subsequent siblings)
  11 siblings, 0 replies; 22+ messages in thread
From: Nicolas Saenz Julienne @ 2020-12-11 16:47 UTC (permalink / raw)
  To: u.kleine-koenig, linux-kernel, Philipp Zabel
  Cc: f.fainelli, linux-pwm, bcm-kernel-feedback-list,
	linux-arm-kernel, devicetree, wahrenst, linux-input,
	dmitry.torokhov, gregkh, devel, linux-gpio, linus.walleij,
	linux-clk, sboyd, linux-rpi-kernel, bgolaszewski,
	andy.shevchenko, Nicolas Saenz Julienne

Use devm_rpi_firmware_get() so as to make sure we release RPi's firmware
interface when unbinding the device.

Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
---
 drivers/reset/reset-raspberrypi.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/reset/reset-raspberrypi.c b/drivers/reset/reset-raspberrypi.c
index 02f59c06f69b..fa23db554bcf 100644
--- a/drivers/reset/reset-raspberrypi.c
+++ b/drivers/reset/reset-raspberrypi.c
@@ -82,7 +82,7 @@ static int rpi_reset_probe(struct platform_device *pdev)
 		return -ENOENT;
 	}
 
-	fw = rpi_firmware_get(np);
+	fw = devm_rpi_firmware_get(&pdev->dev, np);
 	of_node_put(np);
 	if (!fw)
 		return -EPROBE_DEFER;
-- 
2.29.2


^ permalink raw reply	[flat|nested] 22+ messages in thread

* [PATCH v6 06/11] soc: bcm: raspberrypi-power: Release firmware handle on unbind
  2020-12-11 16:47 [PATCH v6 00/11] Raspberry Pi PoE HAT fan support Nicolas Saenz Julienne
                   ` (4 preceding siblings ...)
  2020-12-11 16:47 ` [PATCH v6 05/11] reset: raspberrypi: " Nicolas Saenz Julienne
@ 2020-12-11 16:47 ` Nicolas Saenz Julienne
  2020-12-11 16:47 ` [PATCH v6 07/11] staging: vchiq: " Nicolas Saenz Julienne
                   ` (5 subsequent siblings)
  11 siblings, 0 replies; 22+ messages in thread
From: Nicolas Saenz Julienne @ 2020-12-11 16:47 UTC (permalink / raw)
  To: u.kleine-koenig, linux-kernel
  Cc: f.fainelli, linux-pwm, bcm-kernel-feedback-list,
	linux-arm-kernel, devicetree, wahrenst, linux-input,
	dmitry.torokhov, gregkh, devel, p.zabel, linux-gpio,
	linus.walleij, linux-clk, sboyd, linux-rpi-kernel, bgolaszewski,
	andy.shevchenko, Nicolas Saenz Julienne

Use devm_rpi_firmware_get() so as to make sure we release RPi's firmware
interface when unbinding the device.

Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
---
 drivers/soc/bcm/raspberrypi-power.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/soc/bcm/raspberrypi-power.c b/drivers/soc/bcm/raspberrypi-power.c
index 5d1aacdd84ef..068715d6e66d 100644
--- a/drivers/soc/bcm/raspberrypi-power.c
+++ b/drivers/soc/bcm/raspberrypi-power.c
@@ -177,7 +177,7 @@ static int rpi_power_probe(struct platform_device *pdev)
 		return -ENODEV;
 	}
 
-	rpi_domains->fw = rpi_firmware_get(fw_np);
+	rpi_domains->fw = devm_rpi_firmware_get(&pdev->dev, fw_np);
 	of_node_put(fw_np);
 	if (!rpi_domains->fw)
 		return -EPROBE_DEFER;
-- 
2.29.2


^ permalink raw reply	[flat|nested] 22+ messages in thread

* [PATCH v6 07/11] staging: vchiq: Release firmware handle on unbind
  2020-12-11 16:47 [PATCH v6 00/11] Raspberry Pi PoE HAT fan support Nicolas Saenz Julienne
                   ` (5 preceding siblings ...)
  2020-12-11 16:47 ` [PATCH v6 06/11] soc: bcm: raspberrypi-power: " Nicolas Saenz Julienne
@ 2020-12-11 16:47 ` Nicolas Saenz Julienne
  2020-12-11 16:47 ` [PATCH v6 08/11] input: raspberrypi-ts: Release firmware handle when not needed Nicolas Saenz Julienne
                   ` (4 subsequent siblings)
  11 siblings, 0 replies; 22+ messages in thread
From: Nicolas Saenz Julienne @ 2020-12-11 16:47 UTC (permalink / raw)
  To: u.kleine-koenig, linux-kernel
  Cc: f.fainelli, linux-pwm, bcm-kernel-feedback-list,
	linux-arm-kernel, devicetree, wahrenst, linux-input,
	dmitry.torokhov, gregkh, devel, p.zabel, linux-gpio,
	linus.walleij, linux-clk, sboyd, linux-rpi-kernel, bgolaszewski,
	andy.shevchenko, Nicolas Saenz Julienne

Use devm_rpi_firmware_get() so as to make sure we release RPi's firmware
interface when unbinding the device.

Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
---
 drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c b/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c
index f500a7043805..6c196cade4a0 100644
--- a/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c
+++ b/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c
@@ -2732,7 +2732,7 @@ static int vchiq_probe(struct platform_device *pdev)
 		return -ENOENT;
 	}
 
-	drvdata->fw = rpi_firmware_get(fw_node);
+	drvdata->fw = devm_rpi_firmware_get(&pdev->dev, fw_node);
 	of_node_put(fw_node);
 	if (!drvdata->fw)
 		return -EPROBE_DEFER;
-- 
2.29.2


^ permalink raw reply	[flat|nested] 22+ messages in thread

* [PATCH v6 08/11] input: raspberrypi-ts: Release firmware handle when not needed
  2020-12-11 16:47 [PATCH v6 00/11] Raspberry Pi PoE HAT fan support Nicolas Saenz Julienne
                   ` (6 preceding siblings ...)
  2020-12-11 16:47 ` [PATCH v6 07/11] staging: vchiq: " Nicolas Saenz Julienne
@ 2020-12-11 16:47 ` Nicolas Saenz Julienne
  2020-12-11 18:17   ` Florian Fainelli
  2020-12-11 16:47 ` [PATCH v6 09/11] dt-bindings: pwm: Add binding for RPi firmware PWM bus Nicolas Saenz Julienne
                   ` (3 subsequent siblings)
  11 siblings, 1 reply; 22+ messages in thread
From: Nicolas Saenz Julienne @ 2020-12-11 16:47 UTC (permalink / raw)
  To: u.kleine-koenig, linux-kernel
  Cc: f.fainelli, linux-pwm, bcm-kernel-feedback-list,
	linux-arm-kernel, devicetree, wahrenst, linux-input,
	dmitry.torokhov, gregkh, devel, p.zabel, linux-gpio,
	linus.walleij, linux-clk, sboyd, linux-rpi-kernel, bgolaszewski,
	andy.shevchenko, Nicolas Saenz Julienne

There is no use for the firmware interface after getting the touch
buffer address, so release it.

Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
---

Changes since v5:
 - Correct commit message

Changes since v3:
 - Release firmware handle in probe function

Changes since v2:
 - Use devm_rpi_firmware_get(), instead of remove function

 drivers/input/touchscreen/raspberrypi-ts.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/input/touchscreen/raspberrypi-ts.c b/drivers/input/touchscreen/raspberrypi-ts.c
index ef6aaed217cf..5000f5fd9ec3 100644
--- a/drivers/input/touchscreen/raspberrypi-ts.c
+++ b/drivers/input/touchscreen/raspberrypi-ts.c
@@ -160,7 +160,7 @@ static int rpi_ts_probe(struct platform_device *pdev)
 	touchbuf = (u32)ts->fw_regs_phys;
 	error = rpi_firmware_property(fw, RPI_FIRMWARE_FRAMEBUFFER_SET_TOUCHBUF,
 				      &touchbuf, sizeof(touchbuf));
-
+	rpi_firmware_put(fw);
 	if (error || touchbuf != 0) {
 		dev_warn(dev, "Failed to set touchbuf, %d\n", error);
 		return error;
-- 
2.29.2


^ permalink raw reply	[flat|nested] 22+ messages in thread

* [PATCH v6 09/11] dt-bindings: pwm: Add binding for RPi firmware PWM bus
  2020-12-11 16:47 [PATCH v6 00/11] Raspberry Pi PoE HAT fan support Nicolas Saenz Julienne
                   ` (7 preceding siblings ...)
  2020-12-11 16:47 ` [PATCH v6 08/11] input: raspberrypi-ts: Release firmware handle when not needed Nicolas Saenz Julienne
@ 2020-12-11 16:47 ` Nicolas Saenz Julienne
  2020-12-11 16:47 ` [PATCH v6 10/11] DO NOT MERGE: ARM: dts: Add RPi's official PoE hat support Nicolas Saenz Julienne
                   ` (2 subsequent siblings)
  11 siblings, 0 replies; 22+ messages in thread
From: Nicolas Saenz Julienne @ 2020-12-11 16:47 UTC (permalink / raw)
  To: u.kleine-koenig, linux-kernel, Florian Fainelli, Ray Jui,
	Scott Branden, bcm-kernel-feedback-list, Nicolas Saenz Julienne,
	Eric Anholt, Stefan Wahren
  Cc: linux-pwm, linux-arm-kernel, devicetree, linux-input,
	dmitry.torokhov, gregkh, devel, p.zabel, linux-gpio,
	linus.walleij, linux-clk, sboyd, linux-rpi-kernel, bgolaszewski,
	andy.shevchenko, Rob Herring, Rob Herring

The PWM bus controlling the fan in RPi's official PoE hat can only be
controlled by the board's co-processor.

Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Rob Herring <robh@kernel.org>
---

Changes since v4:
 - Rename compatible string to be more explicit with the bus' limitations

Changes since v3:
 - Fix example

Changes since v1:
 - Update bindings to use 2 #pwm-cells

 .../arm/bcm/raspberrypi,bcm2835-firmware.yaml | 20 +++++++++++++++++++
 .../pwm/raspberrypi,firmware-poe-pwm.h        | 13 ++++++++++++
 2 files changed, 33 insertions(+)
 create mode 100644 include/dt-bindings/pwm/raspberrypi,firmware-poe-pwm.h

diff --git a/Documentation/devicetree/bindings/arm/bcm/raspberrypi,bcm2835-firmware.yaml b/Documentation/devicetree/bindings/arm/bcm/raspberrypi,bcm2835-firmware.yaml
index a2c63c8b1d10..e3664eab0f6a 100644
--- a/Documentation/devicetree/bindings/arm/bcm/raspberrypi,bcm2835-firmware.yaml
+++ b/Documentation/devicetree/bindings/arm/bcm/raspberrypi,bcm2835-firmware.yaml
@@ -64,6 +64,21 @@ properties:
       - compatible
       - "#reset-cells"
 
+  pwm:
+    type: object
+
+    properties:
+      compatible:
+        const: raspberrypi,firmware-poe-pwm
+
+      "#pwm-cells":
+        # See pwm.yaml in this directory for a description of the cells format.
+        const: 2
+
+    required:
+      - compatible
+      - "#pwm-cells"
+
     additionalProperties: false
 
 required:
@@ -87,5 +102,10 @@ examples:
             compatible = "raspberrypi,firmware-reset";
             #reset-cells = <1>;
         };
+
+        pwm: pwm {
+            compatible = "raspberrypi,firmware-poe-pwm";
+            #pwm-cells = <2>;
+        };
     };
 ...
diff --git a/include/dt-bindings/pwm/raspberrypi,firmware-poe-pwm.h b/include/dt-bindings/pwm/raspberrypi,firmware-poe-pwm.h
new file mode 100644
index 000000000000..27c5ce68847b
--- /dev/null
+++ b/include/dt-bindings/pwm/raspberrypi,firmware-poe-pwm.h
@@ -0,0 +1,13 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2020 Nicolas Saenz Julienne
+ * Author: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
+ */
+
+#ifndef _DT_BINDINGS_RASPBERRYPI_FIRMWARE_PWM_H
+#define _DT_BINDINGS_RASPBERRYPI_FIRMWARE_PWM_H
+
+#define RASPBERRYPI_FIRMWARE_PWM_POE		0
+#define RASPBERRYPI_FIRMWARE_PWM_NUM		1
+
+#endif
-- 
2.29.2


^ permalink raw reply	[flat|nested] 22+ messages in thread

* [PATCH v6 10/11] DO NOT MERGE: ARM: dts: Add RPi's official PoE hat support
  2020-12-11 16:47 [PATCH v6 00/11] Raspberry Pi PoE HAT fan support Nicolas Saenz Julienne
                   ` (8 preceding siblings ...)
  2020-12-11 16:47 ` [PATCH v6 09/11] dt-bindings: pwm: Add binding for RPi firmware PWM bus Nicolas Saenz Julienne
@ 2020-12-11 16:47 ` Nicolas Saenz Julienne
  2020-12-11 16:48 ` [PATCH v6 11/11] pwm: Add Raspberry Pi Firmware based PWM bus Nicolas Saenz Julienne
  2021-01-11 21:02 ` [PATCH v6 00/11] Raspberry Pi PoE HAT fan support Nicolas Saenz Julienne
  11 siblings, 0 replies; 22+ messages in thread
From: Nicolas Saenz Julienne @ 2020-12-11 16:47 UTC (permalink / raw)
  To: u.kleine-koenig, linux-kernel, Rob Herring, Nicolas Saenz Julienne
  Cc: f.fainelli, linux-pwm, bcm-kernel-feedback-list,
	linux-arm-kernel, devicetree, wahrenst, linux-input,
	dmitry.torokhov, gregkh, devel, p.zabel, linux-gpio,
	linus.walleij, linux-clk, sboyd, linux-rpi-kernel, bgolaszewski,
	andy.shevchenko

This is an example on how to enable the fan on top of RPi's official PoE
hat.

Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
---
 arch/arm/boot/dts/bcm2711-rpi-4-b.dts | 54 +++++++++++++++++++++++++++
 1 file changed, 54 insertions(+)

diff --git a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
index 403bacf986eb..9ae44620c5b8 100644
--- a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
+++ b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
@@ -5,6 +5,7 @@
 #include "bcm283x-rpi-usb-peripheral.dtsi"
 
 #include <dt-bindings/reset/raspberrypi,firmware-reset.h>
+#include <dt-bindings/pwm/raspberrypi,firmware-poe-pwm.h>
 
 / {
 	compatible = "raspberrypi,4-model-b", "brcm,bcm2711";
@@ -68,6 +69,54 @@ sd_vcc_reg: sd_vcc_reg {
 		enable-active-high;
 		gpio = <&expgpio 6 GPIO_ACTIVE_HIGH>;
 	};
+
+	fan: pwm-fan {
+		compatible = "pwm-fan";
+		cooling-levels = <0 50 150 255>;
+		#cooling-cells = <2>;
+		pwms = <&fwpwm RASPBERRYPI_FIRMWARE_PWM_POE 80000>;
+	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			trips {
+				threshold: trip-point@0 {
+					temperature = <45000>;
+					hysteresis = <5000>;
+					type = "active";
+				};
+
+				target: trip-point@1 {
+					temperature = <50000>;
+					hysteresis = <2000>;
+					type = "active";
+				};
+
+				cpu_hot: cpu_hot@0 {
+					temperature = <55000>;
+					hysteresis = <2000>;
+					type = "active";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&threshold>;
+					cooling-device = <&fan 0 1>;
+				};
+
+				map1 {
+					trip = <&target>;
+					cooling-device = <&fan 1 2>;
+				};
+
+				map2 {
+					trip = <&cpu_hot>;
+					cooling-device = <&fan 2 3>;
+				};
+			};
+		};
+	};
 };
 
 &ddc0 {
@@ -103,6 +152,11 @@ reset: reset {
 		compatible = "raspberrypi,firmware-reset";
 		#reset-cells = <1>;
 	};
+
+	fwpwm: pwm {
+		compatible = "raspberrypi,firmware-poe-pwm";
+		#pwm-cells = <2>;
+	};
 };
 
 &gpio {
-- 
2.29.2


^ permalink raw reply	[flat|nested] 22+ messages in thread

* [PATCH v6 11/11] pwm: Add Raspberry Pi Firmware based PWM bus
  2020-12-11 16:47 [PATCH v6 00/11] Raspberry Pi PoE HAT fan support Nicolas Saenz Julienne
                   ` (9 preceding siblings ...)
  2020-12-11 16:47 ` [PATCH v6 10/11] DO NOT MERGE: ARM: dts: Add RPi's official PoE hat support Nicolas Saenz Julienne
@ 2020-12-11 16:48 ` Nicolas Saenz Julienne
  2021-01-12  9:18   ` Uwe Kleine-König
  2021-01-11 21:02 ` [PATCH v6 00/11] Raspberry Pi PoE HAT fan support Nicolas Saenz Julienne
  11 siblings, 1 reply; 22+ messages in thread
From: Nicolas Saenz Julienne @ 2020-12-11 16:48 UTC (permalink / raw)
  To: u.kleine-koenig, linux-kernel, Thierry Reding, Lee Jones
  Cc: f.fainelli, linux-pwm, bcm-kernel-feedback-list,
	linux-arm-kernel, devicetree, wahrenst, linux-input,
	dmitry.torokhov, gregkh, devel, p.zabel, linux-gpio,
	linus.walleij, linux-clk, sboyd, linux-rpi-kernel, bgolaszewski,
	andy.shevchenko, Nicolas Saenz Julienne

Adds support to control the PWM bus available in official Raspberry Pi
PoE HAT. Only RPi's co-processor has access to it, so commands have to
be sent through RPi's firmware mailbox interface.

Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
---

Changes since v3:
 - Rename compatible string to be more explicit WRT to bus's limitations

Changes since v2:
 - Use devm_rpi_firmware_get()
 - Rename driver
 - Small cleanups

Changes since v1:
 - Use default pwm bindings and get rid of xlate() function
 - Correct spelling errors
 - Correct apply() function
 - Round values
 - Fix divisions in arm32 mode
 - Small cleanups

 drivers/pwm/Kconfig               |   9 ++
 drivers/pwm/Makefile              |   1 +
 drivers/pwm/pwm-raspberrypi-poe.c | 216 ++++++++++++++++++++++++++++++
 3 files changed, 226 insertions(+)
 create mode 100644 drivers/pwm/pwm-raspberrypi-poe.c

diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
index 0937e1c047ac..75e2344703b3 100644
--- a/drivers/pwm/Kconfig
+++ b/drivers/pwm/Kconfig
@@ -423,6 +423,15 @@ config PWM_PXA
 	  To compile this driver as a module, choose M here: the module
 	  will be called pwm-pxa.
 
+config PWM_RASPBERRYPI_POE
+	tristate "Raspberry Pi Firwmware PoE Hat PWM support"
+	# Make sure not 'y' when RASPBERRYPI_FIRMWARE is 'm'. This can only
+	# happen when COMPILE_TEST=y, hence the added !RASPBERRYPI_FIRMWARE.
+	depends on RASPBERRYPI_FIRMWARE || (COMPILE_TEST && !RASPBERRYPI_FIRMWARE)
+	help
+	  Enable Raspberry Pi firmware controller PWM bus used to control the
+	  official RPI PoE hat
+
 config PWM_RCAR
 	tristate "Renesas R-Car PWM support"
 	depends on ARCH_RENESAS || COMPILE_TEST
diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile
index 18b89d7fd092..ed28d7bd4c64 100644
--- a/drivers/pwm/Makefile
+++ b/drivers/pwm/Makefile
@@ -38,6 +38,7 @@ obj-$(CONFIG_PWM_MXS)		+= pwm-mxs.o
 obj-$(CONFIG_PWM_OMAP_DMTIMER)	+= pwm-omap-dmtimer.o
 obj-$(CONFIG_PWM_PCA9685)	+= pwm-pca9685.o
 obj-$(CONFIG_PWM_PXA)		+= pwm-pxa.o
+obj-$(CONFIG_PWM_RASPBERRYPI_POE)	+= pwm-raspberrypi-poe.o
 obj-$(CONFIG_PWM_RCAR)		+= pwm-rcar.o
 obj-$(CONFIG_PWM_RENESAS_TPU)	+= pwm-renesas-tpu.o
 obj-$(CONFIG_PWM_ROCKCHIP)	+= pwm-rockchip.o
diff --git a/drivers/pwm/pwm-raspberrypi-poe.c b/drivers/pwm/pwm-raspberrypi-poe.c
new file mode 100644
index 000000000000..24b498839fcc
--- /dev/null
+++ b/drivers/pwm/pwm-raspberrypi-poe.c
@@ -0,0 +1,216 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2020 Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
+ * For more information on Raspberry Pi's PoE hat see:
+ * https://www.raspberrypi.org/products/poe-hat/
+ *
+ * Limitations:
+ *  - No disable bit, so a disabled PWM is simulated by duty_cycle 0
+ *  - Only normal polarity
+ *  - Fixed 12.5 kHz period
+ *
+ * The current period is completed when HW is reconfigured.
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pwm.h>
+
+#include <soc/bcm2835/raspberrypi-firmware.h>
+#include <dt-bindings/pwm/raspberrypi,firmware-poe-pwm.h>
+
+#define RPI_PWM_MAX_DUTY		255
+#define RPI_PWM_PERIOD_NS		80000 /* 12.5 kHz */
+
+#define RPI_PWM_CUR_DUTY_REG		0x0
+#define RPI_PWM_DEF_DUTY_REG		0x1
+
+struct raspberrypi_pwm {
+	struct rpi_firmware *firmware;
+	struct pwm_chip chip;
+	unsigned int duty_cycle;
+};
+
+struct raspberrypi_pwm_prop {
+	__le32 reg;
+	__le32 val;
+	__le32 ret;
+} __packed;
+
+static inline struct raspberrypi_pwm *to_raspberrypi_pwm(struct pwm_chip *chip)
+{
+	return container_of(chip, struct raspberrypi_pwm, chip);
+}
+
+static int raspberrypi_pwm_set_property(struct rpi_firmware *firmware,
+					u32 reg, u32 val)
+{
+	struct raspberrypi_pwm_prop msg = {
+		.reg = cpu_to_le32(reg),
+		.val = cpu_to_le32(val),
+	};
+	int ret;
+
+	ret = rpi_firmware_property(firmware, RPI_FIRMWARE_SET_POE_HAT_VAL,
+				    &msg, sizeof(msg));
+	if (ret)
+		return ret;
+	if (msg.ret)
+		return -EIO;
+
+	return 0;
+}
+
+static int raspberrypi_pwm_get_property(struct rpi_firmware *firmware,
+					u32 reg, u32 *val)
+{
+	struct raspberrypi_pwm_prop msg = {
+		.reg = reg
+	};
+	int ret;
+
+	ret = rpi_firmware_property(firmware, RPI_FIRMWARE_GET_POE_HAT_VAL,
+				    &msg, sizeof(msg));
+	if (ret)
+		return ret;
+	if (msg.ret)
+		return -EIO;
+
+	*val = le32_to_cpu(msg.val);
+
+	return 0;
+}
+
+static void raspberrypi_pwm_get_state(struct pwm_chip *chip,
+				      struct pwm_device *pwm,
+				      struct pwm_state *state)
+{
+	struct raspberrypi_pwm *rpipwm = to_raspberrypi_pwm(chip);
+
+	state->period = RPI_PWM_PERIOD_NS;
+	state->duty_cycle = DIV_ROUND_CLOSEST(rpipwm->duty_cycle * RPI_PWM_PERIOD_NS,
+					      RPI_PWM_MAX_DUTY);
+	state->enabled = !!(rpipwm->duty_cycle);
+	state->polarity = PWM_POLARITY_NORMAL;
+}
+
+static int raspberrypi_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
+			         const struct pwm_state *state)
+{
+	struct raspberrypi_pwm *rpipwm = to_raspberrypi_pwm(chip);
+	unsigned int duty_cycle;
+	int ret;
+
+        if (state->period < RPI_PWM_PERIOD_NS ||
+            state->polarity != PWM_POLARITY_NORMAL)
+                return -EINVAL;
+
+        if (!state->enabled)
+                duty_cycle = 0;
+        else if (state->duty_cycle < RPI_PWM_PERIOD_NS)
+                duty_cycle = DIV_ROUND_CLOSEST_ULL(state->duty_cycle * RPI_PWM_MAX_DUTY,
+					           RPI_PWM_PERIOD_NS);
+        else
+                duty_cycle = RPI_PWM_MAX_DUTY;
+
+	if (duty_cycle == rpipwm->duty_cycle)
+		return 0;
+
+	ret = raspberrypi_pwm_set_property(rpipwm->firmware, RPI_PWM_CUR_DUTY_REG,
+					   duty_cycle);
+	if (ret) {
+		dev_err(chip->dev, "Failed to set duty cycle: %d\n", ret);
+		return ret;
+	}
+
+	/*
+	 * This sets the default duty cycle after resetting the board, we
+	 * updated it every time to mimic Raspberry Pi's downstream's driver
+	 * behaviour.
+	 */
+	ret = raspberrypi_pwm_set_property(rpipwm->firmware, RPI_PWM_DEF_DUTY_REG,
+					   duty_cycle);
+	if (ret) {
+		dev_err(chip->dev, "Failed to set default duty cycle: %d\n", ret);
+		return ret;
+	}
+
+        rpipwm->duty_cycle = duty_cycle;
+
+	return 0;
+}
+
+static const struct pwm_ops raspberrypi_pwm_ops = {
+	.get_state = raspberrypi_pwm_get_state,
+	.apply = raspberrypi_pwm_apply,
+	.owner = THIS_MODULE,
+};
+
+static int raspberrypi_pwm_probe(struct platform_device *pdev)
+{
+	struct device_node *firmware_node;
+	struct device *dev = &pdev->dev;
+	struct rpi_firmware *firmware;
+	struct raspberrypi_pwm *rpipwm;
+	int ret;
+
+	firmware_node = of_get_parent(dev->of_node);
+	if (!firmware_node) {
+		dev_err(dev, "Missing firmware node\n");
+		return -ENOENT;
+	}
+
+	firmware = devm_rpi_firmware_get(&pdev->dev, firmware_node);
+	of_node_put(firmware_node);
+	if (!firmware)
+		return -EPROBE_DEFER;
+
+	rpipwm = devm_kzalloc(&pdev->dev, sizeof(*rpipwm), GFP_KERNEL);
+	if (!rpipwm)
+		return -ENOMEM;
+
+	rpipwm->firmware = firmware;
+	rpipwm->chip.dev = dev;
+	rpipwm->chip.ops = &raspberrypi_pwm_ops;
+	rpipwm->chip.base = -1;
+	rpipwm->chip.npwm = RASPBERRYPI_FIRMWARE_PWM_NUM;
+
+	platform_set_drvdata(pdev, rpipwm);
+
+	ret = raspberrypi_pwm_get_property(rpipwm->firmware, RPI_PWM_CUR_DUTY_REG,
+					   &rpipwm->duty_cycle);
+	if (ret) {
+		dev_err(dev, "Failed to get duty cycle: %d\n", ret);
+		return ret;
+	}
+
+	return pwmchip_add(&rpipwm->chip);
+}
+
+static int raspberrypi_pwm_remove(struct platform_device *pdev)
+{
+	struct raspberrypi_pwm *rpipwm = platform_get_drvdata(pdev);
+
+	return pwmchip_remove(&rpipwm->chip);
+}
+
+static const struct of_device_id raspberrypi_pwm_of_match[] = {
+	{ .compatible = "raspberrypi,firmware-poe-pwm", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, raspberrypi_pwm_of_match);
+
+static struct platform_driver raspberrypi_pwm_driver = {
+	.driver = {
+		.name = "raspberrypi-poe-pwm",
+		.of_match_table = raspberrypi_pwm_of_match,
+	},
+	.probe = raspberrypi_pwm_probe,
+	.remove = raspberrypi_pwm_remove,
+};
+module_platform_driver(raspberrypi_pwm_driver);
+
+MODULE_AUTHOR("Nicolas Saenz Julienne <nsaenzjulienne@suse.de>");
+MODULE_DESCRIPTION("Raspberry Pi Firwmare Based PWM Bus Driver");
+MODULE_LICENSE("GPL v2");
-- 
2.29.2


^ permalink raw reply	[flat|nested] 22+ messages in thread

* Re: [PATCH v6 08/11] input: raspberrypi-ts: Release firmware handle when not needed
  2020-12-11 16:47 ` [PATCH v6 08/11] input: raspberrypi-ts: Release firmware handle when not needed Nicolas Saenz Julienne
@ 2020-12-11 18:17   ` Florian Fainelli
  0 siblings, 0 replies; 22+ messages in thread
From: Florian Fainelli @ 2020-12-11 18:17 UTC (permalink / raw)
  To: Nicolas Saenz Julienne, u.kleine-koenig, linux-kernel
  Cc: f.fainelli, linux-pwm, bcm-kernel-feedback-list,
	linux-arm-kernel, devicetree, wahrenst, linux-input,
	dmitry.torokhov, gregkh, devel, p.zabel, linux-gpio,
	linus.walleij, linux-clk, sboyd, linux-rpi-kernel, bgolaszewski,
	andy.shevchenko

[-- Attachment #1: Type: text/plain, Size: 343 bytes --]

On 12/11/20 8:47 AM, Nicolas Saenz Julienne wrote:
> There is no use for the firmware interface after getting the touch
> buffer address, so release it.
> 
> Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
-- 
Florian

[-- Attachment #2: S/MIME Cryptographic Signature --]
[-- Type: application/pkcs7-signature, Size: 4178 bytes --]

^ permalink raw reply	[flat|nested] 22+ messages in thread

* Re: [PATCH v6 03/11] clk: bcm: rpi: Release firmware handle on unbind
  2020-12-11 16:47 ` [PATCH v6 03/11] clk: bcm: rpi: Release firmware handle on unbind Nicolas Saenz Julienne
@ 2020-12-13  5:12   ` Stephen Boyd
  0 siblings, 0 replies; 22+ messages in thread
From: Stephen Boyd @ 2020-12-13  5:12 UTC (permalink / raw)
  To: Nicolas Saenz Julienne, linux-kernel, u.kleine-koenig
  Cc: f.fainelli, linux-pwm, bcm-kernel-feedback-list,
	linux-arm-kernel, devicetree, wahrenst, linux-input,
	dmitry.torokhov, gregkh, devel, p.zabel, linux-gpio,
	linus.walleij, linux-clk, linux-rpi-kernel, bgolaszewski,
	andy.shevchenko, Nicolas Saenz Julienne, Michael Turquette

Quoting Nicolas Saenz Julienne (2020-12-11 08:47:52)
> Use devm_rpi_firmware_get() so as to make sure we release RPi's firmware
> interface when unbinding the device.
> 
> Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
> ---

Acked-by: Stephen Boyd <sboyd@kernel.org>

^ permalink raw reply	[flat|nested] 22+ messages in thread

* Re: [PATCH v6 01/11] firmware: raspberrypi: Keep count of all consumers
  2020-12-11 16:47 ` [PATCH v6 01/11] firmware: raspberrypi: Keep count of all consumers Nicolas Saenz Julienne
@ 2020-12-13  5:14   ` Stephen Boyd
  2020-12-16 10:37   ` Bartosz Golaszewski
  1 sibling, 0 replies; 22+ messages in thread
From: Stephen Boyd @ 2020-12-13  5:14 UTC (permalink / raw)
  To: Florian Fainelli, Nicolas Saenz Julienne, Ray Jui, Scott Branden,
	bcm-kernel-feedback-list, linux-kernel, u.kleine-koenig
  Cc: linux-pwm, linux-arm-kernel, devicetree, wahrenst, linux-input,
	dmitry.torokhov, gregkh, devel, p.zabel, linux-gpio,
	linus.walleij, linux-clk, linux-rpi-kernel, bgolaszewski,
	andy.shevchenko

Quoting Nicolas Saenz Julienne (2020-12-11 08:47:50)
> When unbinding the firmware device we need to make sure it has no
> consumers left. Otherwise we'd leave them with a firmware handle
> pointing at freed memory.
> 
> Keep a reference count of all consumers and introduce rpi_firmware_put()
> which will permit automatically decrease the reference count upon
> unbinding consumer drivers.
> 
> Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
> Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
> 
> ---

Reviewed-by: Stephen Boyd <sboyd@kernel.org>

^ permalink raw reply	[flat|nested] 22+ messages in thread

* Re: [PATCH v6 02/11] firmware: raspberrypi: Introduce devm_rpi_firmware_get()
  2020-12-11 16:47 ` [PATCH v6 02/11] firmware: raspberrypi: Introduce devm_rpi_firmware_get() Nicolas Saenz Julienne
@ 2020-12-16 10:35   ` Bartosz Golaszewski
  2020-12-16 10:37     ` Nicolas Saenz Julienne
  0 siblings, 1 reply; 22+ messages in thread
From: Bartosz Golaszewski @ 2020-12-16 10:35 UTC (permalink / raw)
  To: Nicolas Saenz Julienne
  Cc: Uwe Kleine-König, LKML, Florian Fainelli, Ray Jui,
	Scott Branden, bcm-kernel-feedback-list, linux-pwm, arm-soc,
	linux-devicetree, wahrenst, Linux Input, Dmitry Torokhov,
	Greg KH, devel, Philipp Zabel, linux-gpio, Linus Walleij,
	linux-clk, Stephen Boyd, linux-rpi-kernel, Andy Shevchenko

On Fri, Dec 11, 2020 at 5:48 PM Nicolas Saenz Julienne
<nsaenzjulienne@suse.de> wrote:
>
> It'll simplify the firmware handling for most consumers.
>
> Suggested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
> Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
> ---
>
> Changes since v4:
>  - Rearrange function calls for clarity, same functionality
>
> Changes since v2:
> - Create devm_rpi_firmware_get()
>
>  drivers/firmware/raspberrypi.c             | 29 ++++++++++++++++++++++
>  include/soc/bcm2835/raspberrypi-firmware.h |  8 ++++++
>  2 files changed, 37 insertions(+)
>
> diff --git a/drivers/firmware/raspberrypi.c b/drivers/firmware/raspberrypi.c
> index b65e4c495772..250e01680742 100644
> --- a/drivers/firmware/raspberrypi.c
> +++ b/drivers/firmware/raspberrypi.c
> @@ -243,6 +243,13 @@ void rpi_firmware_put(struct rpi_firmware *fw)
>  }
>  EXPORT_SYMBOL_GPL(rpi_firmware_put);
>
> +static void devm_rpi_firmware_put(void *data)
> +{
> +       struct rpi_firmware *fw = data;
> +
> +       rpi_firmware_put(fw);
> +}
> +
>  static int rpi_firmware_probe(struct platform_device *pdev)
>  {
>         struct device *dev = &pdev->dev;
> @@ -331,6 +338,28 @@ struct rpi_firmware *rpi_firmware_get(struct device_node *firmware_node)
>  }
>  EXPORT_SYMBOL_GPL(rpi_firmware_get);
>
> +/**
> + * devm_rpi_firmware_get - Get pointer to rpi_firmware structure.
> + * @firmware_node:    Pointer to the firmware Device Tree node.
> + *
> + * Returns NULL is the firmware device is not ready.
> + */
> +struct rpi_firmware *devm_rpi_firmware_get(struct device *dev,
> +                                          struct device_node *firmware_node)
> +{
> +       struct rpi_firmware *fw;
> +
> +       fw = rpi_firmware_get(firmware_node);
> +       if (!fw)
> +               return NULL;
> +
> +       if (devm_add_action_or_reset(dev, devm_rpi_firmware_put, fw))
> +               return NULL;
> +
> +       return fw;
> +}
> +EXPORT_SYMBOL_GPL(devm_rpi_firmware_get);
> +
>  static const struct of_device_id rpi_firmware_of_match[] = {
>         { .compatible = "raspberrypi,bcm2835-firmware", },
>         {},
> diff --git a/include/soc/bcm2835/raspberrypi-firmware.h b/include/soc/bcm2835/raspberrypi-firmware.h
> index fdfef7fe40df..73ad784fca96 100644
> --- a/include/soc/bcm2835/raspberrypi-firmware.h
> +++ b/include/soc/bcm2835/raspberrypi-firmware.h
> @@ -142,6 +142,8 @@ int rpi_firmware_property_list(struct rpi_firmware *fw,
>                                void *data, size_t tag_size);
>  void rpi_firmware_put(struct rpi_firmware *fw);
>  struct rpi_firmware *rpi_firmware_get(struct device_node *firmware_node);
> +struct rpi_firmware *devm_rpi_firmware_get(struct device *dev,
> +                                          struct device_node *firmware_node);
>  #else
>  static inline int rpi_firmware_property(struct rpi_firmware *fw, u32 tag,
>                                         void *data, size_t len)
> @@ -160,6 +162,12 @@ static inline struct rpi_firmware *rpi_firmware_get(struct device_node *firmware
>  {
>         return NULL;
>  }
> +
> +static inline struct rpi_firmware *devm_rpi_firmware_get(struct device *dev,
> +                                       struct device_node *firmware_node)
> +{
> +       return NULL;
> +}
>  #endif
>
>  #endif /* __SOC_RASPBERRY_FIRMWARE_H__ */
> --
> 2.29.2
>

Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

^ permalink raw reply	[flat|nested] 22+ messages in thread

* Re: [PATCH v6 02/11] firmware: raspberrypi: Introduce devm_rpi_firmware_get()
  2020-12-16 10:35   ` Bartosz Golaszewski
@ 2020-12-16 10:37     ` Nicolas Saenz Julienne
  0 siblings, 0 replies; 22+ messages in thread
From: Nicolas Saenz Julienne @ 2020-12-16 10:37 UTC (permalink / raw)
  To: Bartosz Golaszewski
  Cc: Uwe Kleine-König, LKML, Florian Fainelli, Ray Jui,
	Scott Branden, bcm-kernel-feedback-list, linux-pwm, arm-soc,
	linux-devicetree, wahrenst, Linux Input, Dmitry Torokhov,
	Greg KH, devel, Philipp Zabel, linux-gpio, Linus Walleij,
	linux-clk, Stephen Boyd, linux-rpi-kernel, Andy Shevchenko

[-- Attachment #1: Type: text/plain, Size: 3989 bytes --]

On Wed, 2020-12-16 at 11:35 +0100, Bartosz Golaszewski wrote:
> On Fri, Dec 11, 2020 at 5:48 PM Nicolas Saenz Julienne
> <nsaenzjulienne@suse.de> wrote:
> > 
> > It'll simplify the firmware handling for most consumers.
> > 
> > Suggested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
> > Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
> > Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
> > ---
> > 
> > Changes since v4:
> >  - Rearrange function calls for clarity, same functionality
> > 
> > Changes since v2:
> > - Create devm_rpi_firmware_get()
> > 
> >  drivers/firmware/raspberrypi.c             | 29 ++++++++++++++++++++++
> >  include/soc/bcm2835/raspberrypi-firmware.h |  8 ++++++
> >  2 files changed, 37 insertions(+)
> > 
> > diff --git a/drivers/firmware/raspberrypi.c b/drivers/firmware/raspberrypi.c
> > index b65e4c495772..250e01680742 100644
> > --- a/drivers/firmware/raspberrypi.c
> > +++ b/drivers/firmware/raspberrypi.c
> > @@ -243,6 +243,13 @@ void rpi_firmware_put(struct rpi_firmware *fw)
> >  }
> >  EXPORT_SYMBOL_GPL(rpi_firmware_put);
> > 
> > +static void devm_rpi_firmware_put(void *data)
> > +{
> > +       struct rpi_firmware *fw = data;
> > +
> > +       rpi_firmware_put(fw);
> > +}
> > +
> >  static int rpi_firmware_probe(struct platform_device *pdev)
> >  {
> >         struct device *dev = &pdev->dev;
> > @@ -331,6 +338,28 @@ struct rpi_firmware *rpi_firmware_get(struct device_node *firmware_node)
> >  }
> >  EXPORT_SYMBOL_GPL(rpi_firmware_get);
> > 
> > +/**
> > + * devm_rpi_firmware_get - Get pointer to rpi_firmware structure.
> > + * @firmware_node:    Pointer to the firmware Device Tree node.
> > + *
> > + * Returns NULL is the firmware device is not ready.
> > + */
> > +struct rpi_firmware *devm_rpi_firmware_get(struct device *dev,
> > +                                          struct device_node *firmware_node)
> > +{
> > +       struct rpi_firmware *fw;
> > +
> > +       fw = rpi_firmware_get(firmware_node);
> > +       if (!fw)
> > +               return NULL;
> > +
> > +       if (devm_add_action_or_reset(dev, devm_rpi_firmware_put, fw))
> > +               return NULL;
> > +
> > +       return fw;
> > +}
> > +EXPORT_SYMBOL_GPL(devm_rpi_firmware_get);
> > +
> >  static const struct of_device_id rpi_firmware_of_match[] = {
> >         { .compatible = "raspberrypi,bcm2835-firmware", },
> >         {},
> > diff --git a/include/soc/bcm2835/raspberrypi-firmware.h b/include/soc/bcm2835/raspberrypi-firmware.h
> > index fdfef7fe40df..73ad784fca96 100644
> > --- a/include/soc/bcm2835/raspberrypi-firmware.h
> > +++ b/include/soc/bcm2835/raspberrypi-firmware.h
> > @@ -142,6 +142,8 @@ int rpi_firmware_property_list(struct rpi_firmware *fw,
> >                                void *data, size_t tag_size);
> >  void rpi_firmware_put(struct rpi_firmware *fw);
> >  struct rpi_firmware *rpi_firmware_get(struct device_node *firmware_node);
> > +struct rpi_firmware *devm_rpi_firmware_get(struct device *dev,
> > +                                          struct device_node *firmware_node);
> >  #else
> >  static inline int rpi_firmware_property(struct rpi_firmware *fw, u32 tag,
> >                                         void *data, size_t len)
> > @@ -160,6 +162,12 @@ static inline struct rpi_firmware *rpi_firmware_get(struct device_node *firmware
> >  {
> >         return NULL;
> >  }
> > +
> > +static inline struct rpi_firmware *devm_rpi_firmware_get(struct device *dev,
> > +                                       struct device_node *firmware_node)
> > +{
> > +       return NULL;
> > +}
> >  #endif
> > 
> >  #endif /* __SOC_RASPBERRY_FIRMWARE_H__ */
> > --
> > 2.29.2
> > 
> 
> Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Thanks for the reviews!


[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

^ permalink raw reply	[flat|nested] 22+ messages in thread

* Re: [PATCH v6 01/11] firmware: raspberrypi: Keep count of all consumers
  2020-12-11 16:47 ` [PATCH v6 01/11] firmware: raspberrypi: Keep count of all consumers Nicolas Saenz Julienne
  2020-12-13  5:14   ` Stephen Boyd
@ 2020-12-16 10:37   ` Bartosz Golaszewski
  1 sibling, 0 replies; 22+ messages in thread
From: Bartosz Golaszewski @ 2020-12-16 10:37 UTC (permalink / raw)
  To: Nicolas Saenz Julienne
  Cc: Uwe Kleine-König, LKML, Florian Fainelli, Ray Jui,
	Scott Branden, bcm-kernel-feedback-list, linux-pwm, arm-soc,
	linux-devicetree, wahrenst, Linux Input, Dmitry Torokhov,
	Greg KH, devel, Philipp Zabel, linux-gpio, Linus Walleij,
	linux-clk, Stephen Boyd, linux-rpi-kernel, Andy Shevchenko

On Fri, Dec 11, 2020 at 5:48 PM Nicolas Saenz Julienne
<nsaenzjulienne@suse.de> wrote:
>
> When unbinding the firmware device we need to make sure it has no
> consumers left. Otherwise we'd leave them with a firmware handle
> pointing at freed memory.
>
> Keep a reference count of all consumers and introduce rpi_firmware_put()
> which will permit automatically decrease the reference count upon
> unbinding consumer drivers.
>
> Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
> Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
>
> ---

Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

^ permalink raw reply	[flat|nested] 22+ messages in thread

* Re: [PATCH v6 00/11] Raspberry Pi PoE HAT fan support
  2020-12-11 16:47 [PATCH v6 00/11] Raspberry Pi PoE HAT fan support Nicolas Saenz Julienne
                   ` (10 preceding siblings ...)
  2020-12-11 16:48 ` [PATCH v6 11/11] pwm: Add Raspberry Pi Firmware based PWM bus Nicolas Saenz Julienne
@ 2021-01-11 21:02 ` Nicolas Saenz Julienne
  2021-01-12  8:52   ` Linus Walleij
  11 siblings, 1 reply; 22+ messages in thread
From: Nicolas Saenz Julienne @ 2021-01-11 21:02 UTC (permalink / raw)
  To: u.kleine-koenig, linux-kernel, gregkh
  Cc: f.fainelli, linux-pwm, bcm-kernel-feedback-list,
	linux-arm-kernel, devicetree, wahrenst, linux-input,
	dmitry.torokhov, gregkh, devel, p.zabel, linux-gpio,
	linus.walleij, linux-clk, sboyd, linux-rpi-kernel, bgolaszewski,
	andy.shevchenko, Eric Anholt

[-- Attachment #1: Type: text/plain, Size: 5092 bytes --]

On Fri, 2020-12-11 at 17:47 +0100, Nicolas Saenz Julienne wrote:
> The aim of this series is to add support to the fan found on RPi's PoE
> HAT. Some commentary on the design can be found below. But the imporant
> part to the people CC'd here not involved with PWM is that, in order to
> achieve this properly, we also have to fix the firmware interface the
> driver uses to communicate with the PWM bus (and many other low level
> functions). Specifically, we have to make sure the firmware interface
> isn't unbound while consumers are still up. So, patch #1 & #2 introduce
> reference counting in the firwmware interface driver and patches #3 to
> #8 update all firmware users. Patches #9 to #11 introduce the new PWM
> driver.
> 
> I sent everything as a single series as the final version of the PWM
> drivers depends on the firwmare fixes, but I'll be happy to split this
> into two separate series if you think it's better.
> 
> --- Original cover letter below ---
> 
> This series aims at adding support to RPi's official PoE HAT fan[1].
> 
> The HW setup is the following:
> 
> > Raspberry Pi                               | PoE HAT                    |
>  arm core -> Mailbox -> RPi co-processor -> I2C -> Atmel MCU -> PWM -> FAN
> 
> The arm cores have only access to the mailbox interface, as i2c0, even if
> physically accessible, is to be used solely by the co-processor
> (VideoCore 4/6).
> 
> This series implements a PWM bus, and has pwm-fan sitting on top of it as per
> this discussion: https://lkml.org/lkml/2018/9/2/486. Although this design has a
> series of shortcomings:
> 
> - It depends on a DT binding: it's not flexible if a new hat shows up with new
>   functionality, we're not 100% sure we'll be able to expand it without
>   breaking backwards compatibility. But without it we can't make use of DT
>   thermal-zones, which IMO is overkill.
> 
> - We're using pwm-fan, writing a hwmon driver would, again, give us more
>   flexibility, but it's not really needed at the moment.
> 
> I personally think that it's not worth the effort, it's unlikely we'll get
> things right in advance. And ultimately, if the RPi people come up with
> something new, we can always write a new driver/bindings from scratch (as in
> not reusing previous code).
> 
> That said, I'm more than happy to change things if there is a consensus that
> another design will do the trick.
> 
> [1] https://www.raspberrypi.org/blog/introducing-power-over-ethernet-poe-hat/
> 
> ---

I'd say at this point the series is pretty clean and, AFAIK, there aren't any
objections. I'm not so sure who should take it, given that it covers numerous
subsystems. Any suggestions on how to handle it?

Regards,
Nicolas

> Changes since v5:
>  - Small cleanups
>  - Add extra code comments
> 
> Changes since v4:
>  - Cleanup devm calls
>  - Rename compatible string so it's unique to the PoE HAT
> 
> Changes since v3:
>  - Split first patch, #1 introduces refcount, then #2 the devm function
>  - Fix touchscreen function
>  - Use kref
> 
> Changes since v2:
>  - Introduce devm_rpi_firmware_get()
>  - Small cleanups in PWM driver
> 
> Changes since v1:
>  - Address PWM driver changes
>  - Fix binding, now with 2 cells
> 
> Nicolas Saenz Julienne (11):
>   firmware: raspberrypi: Keep count of all consumers
>   firmware: raspberrypi: Introduce devm_rpi_firmware_get()
>   clk: bcm: rpi: Release firmware handle on unbind
>   gpio: raspberrypi-exp: Release firmware handle on unbind
>   reset: raspberrypi: Release firmware handle on unbind
>   soc: bcm: raspberrypi-power: Release firmware handle on unbind
>   staging: vchiq: Release firmware handle on unbind
>   input: raspberrypi-ts: Release firmware handle when not needed
>   dt-bindings: pwm: Add binding for RPi firmware PWM bus
>   DO NOT MERGE: ARM: dts: Add RPi's official PoE hat support
>   pwm: Add Raspberry Pi Firmware based PWM bus
> 
>  .../arm/bcm/raspberrypi,bcm2835-firmware.yaml |  20 ++
>  arch/arm/boot/dts/bcm2711-rpi-4-b.dts         |  54 +++++
>  drivers/clk/bcm/clk-raspberrypi.c             |   2 +-
>  drivers/firmware/raspberrypi.c                |  69 +++++-
>  drivers/gpio/gpio-raspberrypi-exp.c           |   2 +-
>  drivers/input/touchscreen/raspberrypi-ts.c    |   2 +-
>  drivers/pwm/Kconfig                           |   9 +
>  drivers/pwm/Makefile                          |   1 +
>  drivers/pwm/pwm-raspberrypi-poe.c             | 216 ++++++++++++++++++
>  drivers/reset/reset-raspberrypi.c             |   2 +-
>  drivers/soc/bcm/raspberrypi-power.c           |   2 +-
>  .../interface/vchiq_arm/vchiq_arm.c           |   2 +-
>  .../pwm/raspberrypi,firmware-poe-pwm.h        |  13 ++
>  include/soc/bcm2835/raspberrypi-firmware.h    |  10 +
>  14 files changed, 395 insertions(+), 9 deletions(-)
>  create mode 100644 drivers/pwm/pwm-raspberrypi-poe.c
>  create mode 100644 include/dt-bindings/pwm/raspberrypi,firmware-poe-pwm.h
> 



[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

^ permalink raw reply	[flat|nested] 22+ messages in thread

* Re: [PATCH v6 00/11] Raspberry Pi PoE HAT fan support
  2021-01-11 21:02 ` [PATCH v6 00/11] Raspberry Pi PoE HAT fan support Nicolas Saenz Julienne
@ 2021-01-12  8:52   ` Linus Walleij
  0 siblings, 0 replies; 22+ messages in thread
From: Linus Walleij @ 2021-01-12  8:52 UTC (permalink / raw)
  To: Nicolas Saenz Julienne
  Cc: Uwe Kleine-König, linux-kernel, Florian Fainelli, linux-pwm,
	bcm-kernel-feedback-list, Linux ARM,
	open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
	Stefan Wahren, Linux Input, Dmitry Torokhov, Greg KH,
	open list:STAGING SUBSYSTEM, Philipp Zabel,
	open list:GPIO SUBSYSTEM, linux-clk, Stephen Boyd,
	linux-rpi-kernel, Bartosz Golaszewski, Andy Shevchenko,
	Eric Anholt

On Mon, Jan 11, 2021 at 10:02 PM Nicolas Saenz Julienne
<nsaenzjulienne@suse.de> wrote:

> I'd say at this point the series is pretty clean and, AFAIK, there aren't any
> objections. I'm not so sure who should take it, given that it covers numerous
> subsystems. Any suggestions on how to handle it?

This is one of those cases where I would suggest collect ACKs
from affected subsystem maintainers and send a pull request
to the SoC tree for this hairy bundle.

Yours,
Linus Walleij

^ permalink raw reply	[flat|nested] 22+ messages in thread

* Re: [PATCH v6 11/11] pwm: Add Raspberry Pi Firmware based PWM bus
  2020-12-11 16:48 ` [PATCH v6 11/11] pwm: Add Raspberry Pi Firmware based PWM bus Nicolas Saenz Julienne
@ 2021-01-12  9:18   ` Uwe Kleine-König
  2021-01-14 18:44     ` Nicolas Saenz Julienne
  0 siblings, 1 reply; 22+ messages in thread
From: Uwe Kleine-König @ 2021-01-12  9:18 UTC (permalink / raw)
  To: Nicolas Saenz Julienne
  Cc: linux-kernel, Thierry Reding, Lee Jones, f.fainelli, linux-pwm,
	bcm-kernel-feedback-list, linux-arm-kernel, devicetree, wahrenst,
	linux-input, dmitry.torokhov, gregkh, devel, p.zabel, linux-gpio,
	linus.walleij, linux-clk, sboyd, linux-rpi-kernel, bgolaszewski,
	andy.shevchenko

[-- Attachment #1: Type: text/plain, Size: 6587 bytes --]

Hello Nicolas,

On Fri, Dec 11, 2020 at 05:48:00PM +0100, Nicolas Saenz Julienne wrote:
> diff --git a/drivers/pwm/pwm-raspberrypi-poe.c b/drivers/pwm/pwm-raspberrypi-poe.c
> new file mode 100644
> index 000000000000..24b498839fcc
> --- /dev/null
> +++ b/drivers/pwm/pwm-raspberrypi-poe.c
> @@ -0,0 +1,216 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright 2020 Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
> + * For more information on Raspberry Pi's PoE hat see:
> + * https://www.raspberrypi.org/products/poe-hat/
> + *
> + * Limitations:
> + *  - No disable bit, so a disabled PWM is simulated by duty_cycle 0
> + *  - Only normal polarity
> + *  - Fixed 12.5 kHz period
> + *
> + * The current period is completed when HW is reconfigured.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/pwm.h>
> +
> +#include <soc/bcm2835/raspberrypi-firmware.h>
> +#include <dt-bindings/pwm/raspberrypi,firmware-poe-pwm.h>
> +
> +#define RPI_PWM_MAX_DUTY		255
> +#define RPI_PWM_PERIOD_NS		80000 /* 12.5 kHz */
> +
> +#define RPI_PWM_CUR_DUTY_REG		0x0
> +#define RPI_PWM_DEF_DUTY_REG		0x1
> +
> +struct raspberrypi_pwm {
> +	struct rpi_firmware *firmware;
> +	struct pwm_chip chip;
> +	unsigned int duty_cycle;
> +};
> +
> +struct raspberrypi_pwm_prop {
> +	__le32 reg;
> +	__le32 val;
> +	__le32 ret;
> +} __packed;
> +
> +static inline struct raspberrypi_pwm *to_raspberrypi_pwm(struct pwm_chip *chip)

I'd like to see this function use the same prefix as the other
functions. I suggest "raspberrypi_pwm_from_chip".

> +{
> +	return container_of(chip, struct raspberrypi_pwm, chip);
> +}
> +
> +static int raspberrypi_pwm_set_property(struct rpi_firmware *firmware,
> +					u32 reg, u32 val)
> +{
> +	struct raspberrypi_pwm_prop msg = {
> +		.reg = cpu_to_le32(reg),
> +		.val = cpu_to_le32(val),
> +	};
> +	int ret;
> +
> +	ret = rpi_firmware_property(firmware, RPI_FIRMWARE_SET_POE_HAT_VAL,
> +				    &msg, sizeof(msg));
> +	if (ret)
> +		return ret;
> +	if (msg.ret)
> +		return -EIO;
> +
> +	return 0;
> +}
> +
> +static int raspberrypi_pwm_get_property(struct rpi_firmware *firmware,
> +					u32 reg, u32 *val)
> +{
> +	struct raspberrypi_pwm_prop msg = {
> +		.reg = reg
> +	};
> +	int ret;
> +
> +	ret = rpi_firmware_property(firmware, RPI_FIRMWARE_GET_POE_HAT_VAL,
> +				    &msg, sizeof(msg));
> +	if (ret)
> +		return ret;
> +	if (msg.ret)
> +		return -EIO;
> +
> +	*val = le32_to_cpu(msg.val);
> +
> +	return 0;
> +}
> +
> +static void raspberrypi_pwm_get_state(struct pwm_chip *chip,
> +				      struct pwm_device *pwm,
> +				      struct pwm_state *state)
> +{
> +	struct raspberrypi_pwm *rpipwm = to_raspberrypi_pwm(chip);
> +
> +	state->period = RPI_PWM_PERIOD_NS;
> +	state->duty_cycle = DIV_ROUND_CLOSEST(rpipwm->duty_cycle * RPI_PWM_PERIOD_NS,
> +					      RPI_PWM_MAX_DUTY);

Please round up here ...

> +	state->enabled = !!(rpipwm->duty_cycle);
> +	state->polarity = PWM_POLARITY_NORMAL;
> +}
> +
> +static int raspberrypi_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
> +			         const struct pwm_state *state)
> +{
> +	struct raspberrypi_pwm *rpipwm = to_raspberrypi_pwm(chip);
> +	unsigned int duty_cycle;
> +	int ret;
> +
> +        if (state->period < RPI_PWM_PERIOD_NS ||
> +            state->polarity != PWM_POLARITY_NORMAL)
> +                return -EINVAL;
> +
> +        if (!state->enabled)
> +                duty_cycle = 0;
> +        else if (state->duty_cycle < RPI_PWM_PERIOD_NS)
> +                duty_cycle = DIV_ROUND_CLOSEST_ULL(state->duty_cycle * RPI_PWM_MAX_DUTY,
> +					           RPI_PWM_PERIOD_NS);

... and round down here.

Just to be sure: writing RPI_PWM_MAX_DUTY (i.e. 255) yields 100% duty
cycle, right?

> +        else
> +                duty_cycle = RPI_PWM_MAX_DUTY;
> +
> +	if (duty_cycle == rpipwm->duty_cycle)
> +		return 0;
> +
> +	ret = raspberrypi_pwm_set_property(rpipwm->firmware, RPI_PWM_CUR_DUTY_REG,
> +					   duty_cycle);
> +	if (ret) {
> +		dev_err(chip->dev, "Failed to set duty cycle: %d\n", ret);
> +		return ret;
> +	}
> +
> +	/*
> +	 * This sets the default duty cycle after resetting the board, we
> +	 * updated it every time to mimic Raspberry Pi's downstream's driver
> +	 * behaviour.
> +	 */
> +	ret = raspberrypi_pwm_set_property(rpipwm->firmware, RPI_PWM_DEF_DUTY_REG,
> +					   duty_cycle);
> +	if (ret) {
> +		dev_err(chip->dev, "Failed to set default duty cycle: %d\n", ret);
> +		return ret;
> +	}
> +
> +        rpipwm->duty_cycle = duty_cycle;

Please use tabs for indention. (The general hint is to use checkpatch
which (I hope) tells you about problems like this.)

> +
> +	return 0;
> +}
> +
> +static const struct pwm_ops raspberrypi_pwm_ops = {
> +	.get_state = raspberrypi_pwm_get_state,
> +	.apply = raspberrypi_pwm_apply,
> +	.owner = THIS_MODULE,
> +};
> +
> +static int raspberrypi_pwm_probe(struct platform_device *pdev)
> +{
> +	struct device_node *firmware_node;
> +	struct device *dev = &pdev->dev;
> +	struct rpi_firmware *firmware;
> +	struct raspberrypi_pwm *rpipwm;
> +	int ret;
> +
> +	firmware_node = of_get_parent(dev->of_node);
> +	if (!firmware_node) {
> +		dev_err(dev, "Missing firmware node\n");
> +		return -ENOENT;
> +	}
> +
> +	firmware = devm_rpi_firmware_get(&pdev->dev, firmware_node);
> +	of_node_put(firmware_node);
> +	if (!firmware)
> +		return -EPROBE_DEFER;

Please use dev_err_probe to benefit from recording an error message in
this case.

> +	rpipwm = devm_kzalloc(&pdev->dev, sizeof(*rpipwm), GFP_KERNEL);
> +	if (!rpipwm)
> +		return -ENOMEM;
> +
> +	rpipwm->firmware = firmware;
> +	rpipwm->chip.dev = dev;
> +	rpipwm->chip.ops = &raspberrypi_pwm_ops;
> +	rpipwm->chip.base = -1;
> +	rpipwm->chip.npwm = RASPBERRYPI_FIRMWARE_PWM_NUM;
> +
> +	platform_set_drvdata(pdev, rpipwm);
> +
> +	ret = raspberrypi_pwm_get_property(rpipwm->firmware, RPI_PWM_CUR_DUTY_REG,
> +					   &rpipwm->duty_cycle);
> +	if (ret) {
> +		dev_err(dev, "Failed to get duty cycle: %d\n", ret);

Please use %pe for the error codes (directly or still better by using
dev_err_probe here, too).

> +		return ret;
> +	}
> +
> +	return pwmchip_add(&rpipwm->chip);
> +}
> [...]

Best regards
Uwe

-- 
Pengutronix e.K.                           | Uwe Kleine-König            |
Industrial Linux Solutions                 | https://www.pengutronix.de/ |

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

^ permalink raw reply	[flat|nested] 22+ messages in thread

* Re: [PATCH v6 11/11] pwm: Add Raspberry Pi Firmware based PWM bus
  2021-01-12  9:18   ` Uwe Kleine-König
@ 2021-01-14 18:44     ` Nicolas Saenz Julienne
  0 siblings, 0 replies; 22+ messages in thread
From: Nicolas Saenz Julienne @ 2021-01-14 18:44 UTC (permalink / raw)
  To: Uwe Kleine-König
  Cc: linux-kernel, Thierry Reding, Lee Jones, f.fainelli, linux-pwm,
	bcm-kernel-feedback-list, linux-arm-kernel, devicetree, wahrenst,
	linux-input, dmitry.torokhov, gregkh, devel, p.zabel, linux-gpio,
	linus.walleij, linux-clk, sboyd, linux-rpi-kernel, bgolaszewski,
	andy.shevchenko

[-- Attachment #1: Type: text/plain, Size: 1502 bytes --]

Hi Uwe, thanks for the review.

On Tue, 2021-01-12 at 10:18 +0100, Uwe Kleine-König wrote:

[...]

> > +                duty_cycle = DIV_ROUND_CLOSEST_ULL(state->duty_cycle * RPI_PWM_MAX_DUTY,
> > +					           RPI_PWM_PERIOD_NS);
> 
> ... and round down here.
> 
> Just to be sure: writing RPI_PWM_MAX_DUTY (i.e. 255) yields 100% duty
> cycle, right?

Yes, at 255 the signal is flat.

> > +        else
> > +                duty_cycle = RPI_PWM_MAX_DUTY;
> > +
> > +	if (duty_cycle == rpipwm->duty_cycle)
> > +		return 0;
> > +
> > +	ret = raspberrypi_pwm_set_property(rpipwm->firmware, RPI_PWM_CUR_DUTY_REG,
> > +					   duty_cycle);
> > +	if (ret) {
> > +		dev_err(chip->dev, "Failed to set duty cycle: %d\n", ret);
> > +		return ret;
> > +	}
> > +
> > +	/*
> > +	 * This sets the default duty cycle after resetting the board, we
> > +	 * updated it every time to mimic Raspberry Pi's downstream's driver
> > +	 * behaviour.
> > +	 */
> > +	ret = raspberrypi_pwm_set_property(rpipwm->firmware, RPI_PWM_DEF_DUTY_REG,
> > +					   duty_cycle);
> > +	if (ret) {
> > +		dev_err(chip->dev, "Failed to set default duty cycle: %d\n", ret);
> > +		return ret;
> > +	}
> > +
> > +        rpipwm->duty_cycle = duty_cycle;
> 
> Please use tabs for indention. (The general hint is to use checkpatch
> which (I hope) tells you about problems like this.)

Sorry for that.

I took note of the rest of comments and will update the code.

Regards,
Nicolas



[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

^ permalink raw reply	[flat|nested] 22+ messages in thread

end of thread, other threads:[~2021-01-14 18:45 UTC | newest]

Thread overview: 22+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-12-11 16:47 [PATCH v6 00/11] Raspberry Pi PoE HAT fan support Nicolas Saenz Julienne
2020-12-11 16:47 ` [PATCH v6 01/11] firmware: raspberrypi: Keep count of all consumers Nicolas Saenz Julienne
2020-12-13  5:14   ` Stephen Boyd
2020-12-16 10:37   ` Bartosz Golaszewski
2020-12-11 16:47 ` [PATCH v6 02/11] firmware: raspberrypi: Introduce devm_rpi_firmware_get() Nicolas Saenz Julienne
2020-12-16 10:35   ` Bartosz Golaszewski
2020-12-16 10:37     ` Nicolas Saenz Julienne
2020-12-11 16:47 ` [PATCH v6 03/11] clk: bcm: rpi: Release firmware handle on unbind Nicolas Saenz Julienne
2020-12-13  5:12   ` Stephen Boyd
2020-12-11 16:47 ` [PATCH v6 04/11] gpio: raspberrypi-exp: " Nicolas Saenz Julienne
2020-12-11 16:47 ` [PATCH v6 05/11] reset: raspberrypi: " Nicolas Saenz Julienne
2020-12-11 16:47 ` [PATCH v6 06/11] soc: bcm: raspberrypi-power: " Nicolas Saenz Julienne
2020-12-11 16:47 ` [PATCH v6 07/11] staging: vchiq: " Nicolas Saenz Julienne
2020-12-11 16:47 ` [PATCH v6 08/11] input: raspberrypi-ts: Release firmware handle when not needed Nicolas Saenz Julienne
2020-12-11 18:17   ` Florian Fainelli
2020-12-11 16:47 ` [PATCH v6 09/11] dt-bindings: pwm: Add binding for RPi firmware PWM bus Nicolas Saenz Julienne
2020-12-11 16:47 ` [PATCH v6 10/11] DO NOT MERGE: ARM: dts: Add RPi's official PoE hat support Nicolas Saenz Julienne
2020-12-11 16:48 ` [PATCH v6 11/11] pwm: Add Raspberry Pi Firmware based PWM bus Nicolas Saenz Julienne
2021-01-12  9:18   ` Uwe Kleine-König
2021-01-14 18:44     ` Nicolas Saenz Julienne
2021-01-11 21:02 ` [PATCH v6 00/11] Raspberry Pi PoE HAT fan support Nicolas Saenz Julienne
2021-01-12  8:52   ` Linus Walleij

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).