[PATCH v3 00/35] Fix x2apic enablement and allow more CPUs, clean up I/OAPIC and MSI bitfields

[PATCH v3 00/35] Fix x2apic enablement and allow more CPUs, clean up I/OAPIC and MSI bitfields

[David Woodhouse]

Fix the conditions for enabling x2apic on guests without interrupt 
remapping, and support 15-bit Extended Destination ID to allow 32768 
CPUs without IR on hypervisors that support it.

Make the I/OAPIC code generate its RTE directly from the MSI message
created by the parent irqchip, and fix up a bunch of magic mask/shift
macros to use bitfields for MSI messages and I/OAPIC RTEs while we're
at it.

v3:
 • Lots of bitfield cleanups from Thomas.
 • Disable hyperv-iommu if 15-bit extension is present.
 • Fix inconsistent CONFIG_PCI_MSI/CONFIG_GENERIC_MSI_IRQ in hpet.c
 • Split KVM_FEATURE_MSI_EXT_DEST_ID patch, half of which is going upstream
   through KVM tree (and the other half needs to wait, or have an #ifdef) so
   is left at the top of the tree.

v2:
 • Minor cleanups.
 • Move __irq_msi_compose_msg() to apic.c, make virt_ext_dest_id static.
 • Generate I/OAPIC RTE directly from parent irqchip's MSI messages.
 • Clean up HPET MSI support into hpet.c now that we can.

David Woodhouse (19):
      x86/apic: Fix x2apic enablement without interrupt remapping
      x86/msi: Only use high bits of MSI address for DMAR unit
      x86/apic: Always provide irq_compose_msi_msg() method for vector domain
      x86/hpet: Move MSI support into hpet.c
      x86/ioapic: Generate RTE directly from parent irqchip's MSI message
      genirq/irqdomain: Implement get_name() method on irqchip fwnodes
      x86/apic: Add select() method on vector irqdomain
      iommu/amd: Implement select() method on remapping irqdomain
      iommu/vt-d: Implement select() method on remapping irqdomain
      iommu/hyper-v: Implement select() method on remapping irqdomain
      x86/hpet: Use irq_find_matching_fwspec() to find remapping irqdomain
      x86/ioapic: Use irq_find_matching_fwspec() to find remapping irqdomain
      x86: Kill all traces of irq_remapping_get_irq_domain()
      iommu/vt-d: Simplify intel_irq_remapping_select()
      x86/ioapic: Handle Extended Destination ID field in RTE
      x86/apic: Support 15 bits of APIC ID in MSI where available
      iommu/hyper-v: Disable IRQ pseudo-remapping if 15 bit APIC IDs are available
      x86/kvm: Reserve KVM_FEATURE_MSI_EXT_DEST_ID
      x86/kvm: Enable 15-bit extension when KVM_FEATURE_MSI_EXT_DEST_ID detected

Thomas Gleixner (16):
      x86/apic/uv: Fix inconsistent destination mode
      x86/devicetree: Fix the ioapic interrupt type table
      x86/apic: Cleanup delivery mode defines
      x86/apic: Replace pointless apic::dest_logical usage
      x86/apic: Get rid of apic::dest_logical
      x86/apic: Cleanup destination mode
      genirq/msi: Allow shadow declarations of msi_msg::$member
      x86/msi: Provide msi message shadow structs
      iommu/intel: Use msi_msg shadow structs
      iommu/amd: Use msi_msg shadow structs
      PCI: vmd: Use msi_msg shadow structs
      x86/kvm: Use msi_msg shadow structs
      x86/pci/xen: Use msi_msg shadow structs
      x86/msi: Remove msidef.h
      x86/io_apic: Cleanup trigger/polarity helpers
      x86/ioapic: Cleanup IO/APIC route entry structs

 Documentation/virt/kvm/cpuid.rst      |   4 +
 arch/x86/include/asm/apic.h           |  16 +-
 arch/x86/include/asm/apicdef.h        |  16 +-
 arch/x86/include/asm/hpet.h           |  11 -
 arch/x86/include/asm/hw_irq.h         |  13 +-
 arch/x86/include/asm/io_apic.h        |  79 ++----
 arch/x86/include/asm/irq_remapping.h  |   9 -
 arch/x86/include/asm/irqdomain.h      |   3 +
 arch/x86/include/asm/msi.h            |  50 ++++
 arch/x86/include/asm/msidef.h         |  57 ----
 arch/x86/include/asm/x86_init.h       |   2 +
 arch/x86/include/uapi/asm/kvm_para.h  |   1 +
 arch/x86/kernel/apic/apic.c           |  73 ++++-
 arch/x86/kernel/apic/apic_flat_64.c   |  18 +-
 arch/x86/kernel/apic/apic_noop.c      |  10 +-
 arch/x86/kernel/apic/apic_numachip.c  |  16 +-
 arch/x86/kernel/apic/bigsmp_32.c      |   9 +-
 arch/x86/kernel/apic/io_apic.c        | 503 ++++++++++++++++++----------------
 arch/x86/kernel/apic/ipi.c            |   6 +-
 arch/x86/kernel/apic/msi.c            | 153 +----------
 arch/x86/kernel/apic/probe_32.c       |   9 +-
 arch/x86/kernel/apic/vector.c         |  49 ++++
 arch/x86/kernel/apic/x2apic_cluster.c |  10 +-
 arch/x86/kernel/apic/x2apic_phys.c    |  17 +-
 arch/x86/kernel/apic/x2apic_uv_x.c    |  12 +-
 arch/x86/kernel/devicetree.c          |  30 +-
 arch/x86/kernel/hpet.c                | 122 ++++++++-
 arch/x86/kernel/kvm.c                 |   6 +
 arch/x86/kernel/smpboot.c             |   8 +-
 arch/x86/kernel/x86_init.c            |   1 +
 arch/x86/kvm/irq_comm.c               |  31 +--
 arch/x86/pci/intel_mid_pci.c          |   8 +-
 arch/x86/pci/xen.c                    |  26 +-
 arch/x86/platform/uv/uv_irq.c         |   4 +-
 arch/x86/xen/apic.c                   |   7 +-
 drivers/iommu/amd/amd_iommu_types.h   |   2 +-
 drivers/iommu/amd/init.c              |  46 ++--
 drivers/iommu/amd/iommu.c             |  93 +++----
 drivers/iommu/hyperv-iommu.c          |  44 +--
 drivers/iommu/intel/irq_remapping.c   | 102 +++----
 drivers/iommu/irq_remapping.c         |  14 -
 drivers/iommu/irq_remapping.h         |   3 -
 drivers/pci/controller/pci-hyperv.c   |   6 +-
 drivers/pci/controller/vmd.c          |   9 +-
 include/asm-generic/msi.h             |   4 +
 include/linux/msi.h                   |  46 +++-
 kernel/irq/irqdomain.c                |  11 +-
 47 files changed, 890 insertions(+), 879 deletions(-)



_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 01/35] x86/apic: Fix x2apic enablement without interrupt remapping

[David Woodhouse]

From: David Woodhouse <dwmw@amazon.co.uk>

Currently, Linux as a hypervisor guest will enable x2apic only if there are
no CPUs present at boot time with an APIC ID above 255.

Hotplugging a CPU later with a higher APIC ID would result in a CPU which
cannot be targeted by external interrupts.

Add a filter in x2apic_apic_id_valid() which can be used to prevent such
CPUs from coming online, and allow x2apic to be enabled even if they are
present at boot time.

Fixes: ce69a784504 ("x86/apic: Enable x2APIC without interrupt remapping under KVM")
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
---
 arch/x86/include/asm/apic.h        |  1 +
 arch/x86/kernel/apic/apic.c        | 14 ++++++++------
 arch/x86/kernel/apic/x2apic_phys.c |  9 +++++++++
 3 files changed, 18 insertions(+), 6 deletions(-)

diff --git a/arch/x86/include/asm/apic.h b/arch/x86/include/asm/apic.h
index 1c129abb7f09..b0fd204e0023 100644
--- a/arch/x86/include/asm/apic.h
+++ b/arch/x86/include/asm/apic.h
@@ -259,6 +259,7 @@ static inline u64 native_x2apic_icr_read(void)
 
 extern int x2apic_mode;
 extern int x2apic_phys;
+extern void __init x2apic_set_max_apicid(u32 apicid);
 extern void __init check_x2apic(void);
 extern void x2apic_setup(void);
 static inline int x2apic_enabled(void)
diff --git a/arch/x86/kernel/apic/apic.c b/arch/x86/kernel/apic/apic.c
index b3eef1d5c903..113f6ca7b828 100644
--- a/arch/x86/kernel/apic/apic.c
+++ b/arch/x86/kernel/apic/apic.c
@@ -1841,20 +1841,22 @@ static __init void try_to_enable_x2apic(int remap_mode)
 		return;
 
 	if (remap_mode != IRQ_REMAP_X2APIC_MODE) {
-		/* IR is required if there is APIC ID > 255 even when running
-		 * under KVM
+		/*
+		 * Using X2APIC without IR is not architecturally supported
+		 * on bare metal but may be supported in guests.
 		 */
-		if (max_physical_apicid > 255 ||
-		    !x86_init.hyper.x2apic_available()) {
+		if (!x86_init.hyper.x2apic_available()) {
 			pr_info("x2apic: IRQ remapping doesn't support X2APIC mode\n");
 			x2apic_disable();
 			return;
 		}
 
 		/*
-		 * without IR all CPUs can be addressed by IOAPIC/MSI
-		 * only in physical mode
+		 * Without IR, all CPUs can be addressed by IOAPIC/MSI only
+		 * in physical mode, and CPUs with an APIC ID that cannnot
+		 * be addressed must not be brought online.
 		 */
+		x2apic_set_max_apicid(255);
 		x2apic_phys = 1;
 	}
 	x2apic_enable();
diff --git a/arch/x86/kernel/apic/x2apic_phys.c b/arch/x86/kernel/apic/x2apic_phys.c
index bc9693841353..e14eae6d6ea7 100644
--- a/arch/x86/kernel/apic/x2apic_phys.c
+++ b/arch/x86/kernel/apic/x2apic_phys.c
@@ -8,6 +8,12 @@
 int x2apic_phys;
 
 static struct apic apic_x2apic_phys;
+static u32 x2apic_max_apicid __ro_after_init;
+
+void __init x2apic_set_max_apicid(u32 apicid)
+{
+	x2apic_max_apicid = apicid;
+}
 
 static int __init set_x2apic_phys_mode(char *arg)
 {
@@ -98,6 +104,9 @@ static int x2apic_phys_probe(void)
 /* Common x2apic functions, also used by x2apic_cluster */
 int x2apic_apic_id_valid(u32 apicid)
 {
+	if (x2apic_max_apicid && apicid > x2apic_max_apicid)
+		return 0;
+
 	return 1;
 }
 
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 02/35] x86/msi: Only use high bits of MSI address for DMAR unit

[David Woodhouse]

From: David Woodhouse <dwmw@amazon.co.uk>

The Intel IOMMU has an MSI-like configuration for its interrupt, but it
isn't really MSI. So it gets to abuse the high 32 bits of the address, and
puts the high 24 bits of the extended APIC ID there.

This isn't something that can be used in the general case for real MSIs,
since external devices using the high bits of the address would be
performing writes to actual memory space above 4GiB, not targeted at the
APIC.

Factor the hack out and allow it only to be used when appropriate, adding a
WARN_ON_ONCE() if other MSIs are targeted at an unreachable APIC ID. That
should never happen since the compatibility MSI messages are not used when
Interrupt Remapping is enabled.

The x2apic_enabled() check isn't needed because Linux won't bring up CPUs
with higher APIC IDs unless IR and x2apic are enabled anyway.

Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
---
 arch/x86/kernel/apic/msi.c | 33 +++++++++++++++++++++++++++------
 1 file changed, 27 insertions(+), 6 deletions(-)

diff --git a/arch/x86/kernel/apic/msi.c b/arch/x86/kernel/apic/msi.c
index 6313f0a05db7..516df47bde73 100644
--- a/arch/x86/kernel/apic/msi.c
+++ b/arch/x86/kernel/apic/msi.c
@@ -23,13 +23,11 @@
 
 struct irq_domain *x86_pci_msi_default_domain __ro_after_init;
 
-static void __irq_msi_compose_msg(struct irq_cfg *cfg, struct msi_msg *msg)
+static void __irq_msi_compose_msg(struct irq_cfg *cfg, struct msi_msg *msg,
+				  bool dmar)
 {
 	msg->address_hi = MSI_ADDR_BASE_HI;
 
-	if (x2apic_enabled())
-		msg->address_hi |= MSI_ADDR_EXT_DEST_ID(cfg->dest_apicid);
-
 	msg->address_lo =
 		MSI_ADDR_BASE_LO |
 		((apic->irq_dest_mode == 0) ?
@@ -43,18 +41,29 @@ static void __irq_msi_compose_msg(struct irq_cfg *cfg, struct msi_msg *msg)
 		MSI_DATA_LEVEL_ASSERT |
 		MSI_DATA_DELIVERY_FIXED |
 		MSI_DATA_VECTOR(cfg->vector);
+
+	/*
+	 * Only the IOMMU itself can use the trick of putting destination
+	 * APIC ID into the high bits of the address. Anything else would
+	 * just be writing to memory if it tried that, and needs IR to
+	 * address higher APIC IDs.
+	 */
+	if (dmar)
+		msg->address_hi |= MSI_ADDR_EXT_DEST_ID(cfg->dest_apicid);
+	else
+		WARN_ON_ONCE(MSI_ADDR_EXT_DEST_ID(cfg->dest_apicid));
 }
 
 void x86_vector_msi_compose_msg(struct irq_data *data, struct msi_msg *msg)
 {
-	__irq_msi_compose_msg(irqd_cfg(data), msg);
+	__irq_msi_compose_msg(irqd_cfg(data), msg, false);
 }
 
 static void irq_msi_update_msg(struct irq_data *irqd, struct irq_cfg *cfg)
 {
 	struct msi_msg msg[2] = { [1] = { }, };
 
-	__irq_msi_compose_msg(cfg, msg);
+	__irq_msi_compose_msg(cfg, msg, false);
 	irq_data_get_irq_chip(irqd)->irq_write_msi_msg(irqd, msg);
 }
 
@@ -276,6 +285,17 @@ struct irq_domain *arch_create_remap_msi_irq_domain(struct irq_domain *parent,
 #endif
 
 #ifdef CONFIG_DMAR_TABLE
+/*
+ * The Intel IOMMU (ab)uses the high bits of the MSI address to contain the
+ * high bits of the destination APIC ID. This can't be done in the general
+ * case for MSIs as it would be targeting real memory above 4GiB not the
+ * APIC.
+ */
+static void dmar_msi_compose_msg(struct irq_data *data, struct msi_msg *msg)
+{
+	__irq_msi_compose_msg(irqd_cfg(data), msg, true);
+}
+
 static void dmar_msi_write_msg(struct irq_data *data, struct msi_msg *msg)
 {
 	dmar_msi_write(data->irq, msg);
@@ -288,6 +308,7 @@ static struct irq_chip dmar_msi_controller = {
 	.irq_ack		= irq_chip_ack_parent,
 	.irq_set_affinity	= msi_domain_set_affinity,
 	.irq_retrigger		= irq_chip_retrigger_hierarchy,
+	.irq_compose_msi_msg	= dmar_msi_compose_msg,
 	.irq_write_msi_msg	= dmar_msi_write_msg,
 	.flags			= IRQCHIP_SKIP_SET_WAKE,
 };
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 03/35] x86/apic/uv: Fix inconsistent destination mode

[David Woodhouse]

From: Thomas Gleixner <tglx@linutronix.de>

The UV x2apic is strictly using physical destination mode, but
apic::dest_logical is initialized with APIC_DEST_LOGICAL.

This does not matter much because UV does not use any of the generic
functions which use apic::dest_logical, but is still inconsistent.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
---
 arch/x86/kernel/apic/x2apic_uv_x.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/x86/kernel/apic/x2apic_uv_x.c b/arch/x86/kernel/apic/x2apic_uv_x.c
index 714233cee0b5..9ade9e6a95ff 100644
--- a/arch/x86/kernel/apic/x2apic_uv_x.c
+++ b/arch/x86/kernel/apic/x2apic_uv_x.c
@@ -811,7 +811,7 @@ static struct apic apic_x2apic_uv_x __ro_after_init = {
 	.irq_dest_mode			= 0, /* Physical */
 
 	.disable_esr			= 0,
-	.dest_logical			= APIC_DEST_LOGICAL,
+	.dest_logical			= APIC_DEST_PHYSICAL,
 	.check_apicid_used		= NULL,
 
 	.init_apic_ldr			= uv_init_apic_ldr,
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 04/35] x86/devicetree: Fix the ioapic interrupt type table

[David Woodhouse]

From: Thomas Gleixner <tglx@linutronix.de>

The ioapic interrupt type table is wrong as it assumes that polarity in
IO/APIC context means active high when set. But the IO/APIC polarity is
working the other way round. This works because the ordering of the entries
is consistent with the device tree and the type information is not used by
the IO/APIC interrupt chip.

The whole trigger and polarity business of IO/APIC is misleading and the
corresponding constants which are defined as 0/1 are not used consistently
and are going to be removed.

Rename the type table members to 'is_level' and 'active_low' and adjust the
type information for consistency sake.

No functional change.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
---
 arch/x86/kernel/devicetree.c | 30 +++++++++++++++---------------
 1 file changed, 15 insertions(+), 15 deletions(-)

diff --git a/arch/x86/kernel/devicetree.c b/arch/x86/kernel/devicetree.c
index ddffd80f5c52..6a4cb71c2498 100644
--- a/arch/x86/kernel/devicetree.c
+++ b/arch/x86/kernel/devicetree.c
@@ -184,31 +184,31 @@ static unsigned int ioapic_id;
 
 struct of_ioapic_type {
 	u32 out_type;
-	u32 trigger;
-	u32 polarity;
+	u32 is_level;
+	u32 active_low;
 };
 
 static struct of_ioapic_type of_ioapic_type[] =
 {
 	{
-		.out_type	= IRQ_TYPE_EDGE_RISING,
-		.trigger	= IOAPIC_EDGE,
-		.polarity	= 1,
+		.out_type	= IRQ_TYPE_EDGE_FALLING,
+		.is_level	= 0,
+		.active_low	= 1,
 	},
 	{
-		.out_type	= IRQ_TYPE_LEVEL_LOW,
-		.trigger	= IOAPIC_LEVEL,
-		.polarity	= 0,
+		.out_type	= IRQ_TYPE_LEVEL_HIGH,
+		.is_level	= 1,
+		.active_low	= 0,
 	},
 	{
-		.out_type	= IRQ_TYPE_LEVEL_HIGH,
-		.trigger	= IOAPIC_LEVEL,
-		.polarity	= 1,
+		.out_type	= IRQ_TYPE_LEVEL_LOW,
+		.is_level	= 1,
+		.active_low	= 1,
 	},
 	{
-		.out_type	= IRQ_TYPE_EDGE_FALLING,
-		.trigger	= IOAPIC_EDGE,
-		.polarity	= 0,
+		.out_type	= IRQ_TYPE_EDGE_RISING,
+		.is_level	= 0,
+		.active_low	= 0,
 	},
 };
 
@@ -228,7 +228,7 @@ static int dt_irqdomain_alloc(struct irq_domain *domain, unsigned int virq,
 		return -EINVAL;
 
 	it = &of_ioapic_type[type_index];
-	ioapic_set_alloc_attr(&tmp, NUMA_NO_NODE, it->trigger, it->polarity);
+	ioapic_set_alloc_attr(&tmp, NUMA_NO_NODE, it->is_level, it->active_low);
 	tmp.devid = mpc_ioapic_id(mp_irqdomain_ioapic_idx(domain));
 	tmp.ioapic.pin = fwspec->param[0];
 
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 05/35] x86/apic: Cleanup delivery mode defines

[David Woodhouse]

From: Thomas Gleixner <tglx@linutronix.de>

The enum ioapic_irq_destination_types and the enumerated constants starting
with 'dest_' are gross misnomers because they describe the delivery mode.

Rename then enum and the constants so they actually make sense.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
---
 arch/x86/include/asm/apic.h           |  3 ++-
 arch/x86/include/asm/apicdef.h        | 16 +++++++---------
 arch/x86/kernel/apic/apic_flat_64.c   |  4 ++--
 arch/x86/kernel/apic/apic_noop.c      |  2 +-
 arch/x86/kernel/apic/apic_numachip.c  |  4 ++--
 arch/x86/kernel/apic/bigsmp_32.c      |  2 +-
 arch/x86/kernel/apic/io_apic.c        | 11 ++++++-----
 arch/x86/kernel/apic/probe_32.c       |  2 +-
 arch/x86/kernel/apic/x2apic_cluster.c |  2 +-
 arch/x86/kernel/apic/x2apic_phys.c    |  2 +-
 arch/x86/kernel/apic/x2apic_uv_x.c    |  6 +++---
 arch/x86/platform/uv/uv_irq.c         |  2 +-
 drivers/iommu/amd/iommu.c             |  4 ++--
 drivers/iommu/intel/irq_remapping.c   |  2 +-
 drivers/pci/controller/pci-hyperv.c   |  6 +++---
 15 files changed, 34 insertions(+), 34 deletions(-)

diff --git a/arch/x86/include/asm/apic.h b/arch/x86/include/asm/apic.h
index b0fd204e0023..53bb62e0fdd5 100644
--- a/arch/x86/include/asm/apic.h
+++ b/arch/x86/include/asm/apic.h
@@ -309,7 +309,8 @@ struct apic {
 	/* dest_logical is used by the IPI functions */
 	u32	dest_logical;
 	u32	disable_esr;
-	u32	irq_delivery_mode;
+
+	enum apic_delivery_modes delivery_mode;
 	u32	irq_dest_mode;
 
 	u32	(*calc_dest_apicid)(unsigned int cpu);
diff --git a/arch/x86/include/asm/apicdef.h b/arch/x86/include/asm/apicdef.h
index 05e694ed8386..5716f22f81ac 100644
--- a/arch/x86/include/asm/apicdef.h
+++ b/arch/x86/include/asm/apicdef.h
@@ -432,15 +432,13 @@ struct local_apic {
  #define BAD_APICID 0xFFFFu
 #endif
 
-enum ioapic_irq_destination_types {
-	dest_Fixed		= 0,
-	dest_LowestPrio		= 1,
-	dest_SMI		= 2,
-	dest__reserved_1	= 3,
-	dest_NMI		= 4,
-	dest_INIT		= 5,
-	dest__reserved_2	= 6,
-	dest_ExtINT		= 7
+enum apic_delivery_modes {
+	APIC_DELIVERY_MODE_FIXED	= 0,
+	APIC_DELIVERY_MODE_LOWESTPRIO   = 1,
+	APIC_DELIVERY_MODE_SMI		= 2,
+	APIC_DELIVERY_MODE_NMI		= 4,
+	APIC_DELIVERY_MODE_INIT		= 5,
+	APIC_DELIVERY_MODE_EXTINT	= 7,
 };
 
 #endif /* _ASM_X86_APICDEF_H */
diff --git a/arch/x86/kernel/apic/apic_flat_64.c b/arch/x86/kernel/apic/apic_flat_64.c
index 7862b152a052..fdd38a17f835 100644
--- a/arch/x86/kernel/apic/apic_flat_64.c
+++ b/arch/x86/kernel/apic/apic_flat_64.c
@@ -113,7 +113,7 @@ static struct apic apic_flat __ro_after_init = {
 	.apic_id_valid			= default_apic_id_valid,
 	.apic_id_registered		= flat_apic_id_registered,
 
-	.irq_delivery_mode		= dest_Fixed,
+	.delivery_mode			= APIC_DELIVERY_MODE_FIXED,
 	.irq_dest_mode			= 1, /* logical */
 
 	.disable_esr			= 0,
@@ -206,7 +206,7 @@ static struct apic apic_physflat __ro_after_init = {
 	.apic_id_valid			= default_apic_id_valid,
 	.apic_id_registered		= flat_apic_id_registered,
 
-	.irq_delivery_mode		= dest_Fixed,
+	.delivery_mode			= APIC_DELIVERY_MODE_FIXED,
 	.irq_dest_mode			= 0, /* physical */
 
 	.disable_esr			= 0,
diff --git a/arch/x86/kernel/apic/apic_noop.c b/arch/x86/kernel/apic/apic_noop.c
index 780c702969b7..4fc934b11851 100644
--- a/arch/x86/kernel/apic/apic_noop.c
+++ b/arch/x86/kernel/apic/apic_noop.c
@@ -95,7 +95,7 @@ struct apic apic_noop __ro_after_init = {
 	.apic_id_valid			= default_apic_id_valid,
 	.apic_id_registered		= noop_apic_id_registered,
 
-	.irq_delivery_mode		= dest_Fixed,
+	.delivery_mode			= APIC_DELIVERY_MODE_FIXED,
 	/* logical delivery broadcast to all CPUs: */
 	.irq_dest_mode			= 1,
 
diff --git a/arch/x86/kernel/apic/apic_numachip.c b/arch/x86/kernel/apic/apic_numachip.c
index 35edd57f064a..db715d082ec9 100644
--- a/arch/x86/kernel/apic/apic_numachip.c
+++ b/arch/x86/kernel/apic/apic_numachip.c
@@ -246,7 +246,7 @@ static const struct apic apic_numachip1 __refconst = {
 	.apic_id_valid			= numachip_apic_id_valid,
 	.apic_id_registered		= numachip_apic_id_registered,
 
-	.irq_delivery_mode		= dest_Fixed,
+	.delivery_mode			= APIC_DELIVERY_MODE_FIXED,
 	.irq_dest_mode			= 0, /* physical */
 
 	.disable_esr			= 0,
@@ -295,7 +295,7 @@ static const struct apic apic_numachip2 __refconst = {
 	.apic_id_valid			= numachip_apic_id_valid,
 	.apic_id_registered		= numachip_apic_id_registered,
 
-	.irq_delivery_mode		= dest_Fixed,
+	.delivery_mode			= APIC_DELIVERY_MODE_FIXED,
 	.irq_dest_mode			= 0, /* physical */
 
 	.disable_esr			= 0,
diff --git a/arch/x86/kernel/apic/bigsmp_32.c b/arch/x86/kernel/apic/bigsmp_32.c
index 98d015a4405a..7f6461f5d349 100644
--- a/arch/x86/kernel/apic/bigsmp_32.c
+++ b/arch/x86/kernel/apic/bigsmp_32.c
@@ -127,7 +127,7 @@ static struct apic apic_bigsmp __ro_after_init = {
 	.apic_id_valid			= default_apic_id_valid,
 	.apic_id_registered		= bigsmp_apic_id_registered,
 
-	.irq_delivery_mode		= dest_Fixed,
+	.delivery_mode			= APIC_DELIVERY_MODE_FIXED,
 	/* phys delivery to target CPU: */
 	.irq_dest_mode			= 0,
 
diff --git a/arch/x86/kernel/apic/io_apic.c b/arch/x86/kernel/apic/io_apic.c
index 7b3c7e0d4a09..cff6cbc3d183 100644
--- a/arch/x86/kernel/apic/io_apic.c
+++ b/arch/x86/kernel/apic/io_apic.c
@@ -535,7 +535,7 @@ static void clear_IO_APIC_pin(unsigned int apic, unsigned int pin)
 
 	/* Check delivery_mode to be sure we're not clearing an SMI pin */
 	entry = ioapic_read_entry(apic, pin);
-	if (entry.delivery_mode == dest_SMI)
+	if (entry.delivery_mode == APIC_DELIVERY_MODE_SMI)
 		return;
 
 	/*
@@ -1368,7 +1368,8 @@ void __init enable_IO_APIC(void)
 		/* If the interrupt line is enabled and in ExtInt mode
 		 * I have found the pin where the i8259 is connected.
 		 */
-		if ((entry.mask == 0) && (entry.delivery_mode == dest_ExtINT)) {
+		if ((entry.mask == 0) &&
+		    (entry.delivery_mode == APIC_DELIVERY_MODE_EXTINT)) {
 			ioapic_i8259.apic = apic;
 			ioapic_i8259.pin  = pin;
 			goto found_i8259;
@@ -1416,7 +1417,7 @@ void native_restore_boot_irq_mode(void)
 		entry.trigger		= IOAPIC_EDGE;
 		entry.polarity		= IOAPIC_POL_HIGH;
 		entry.dest_mode		= IOAPIC_DEST_MODE_PHYSICAL;
-		entry.delivery_mode	= dest_ExtINT;
+		entry.delivery_mode	= APIC_DELIVERY_MODE_EXTINT;
 		entry.dest		= read_apic_id();
 
 		/*
@@ -2047,7 +2048,7 @@ static inline void __init unlock_ExtINT_logic(void)
 	entry1.dest_mode = IOAPIC_DEST_MODE_PHYSICAL;
 	entry1.mask = IOAPIC_UNMASKED;
 	entry1.dest = hard_smp_processor_id();
-	entry1.delivery_mode = dest_ExtINT;
+	entry1.delivery_mode = APIC_DELIVERY_MODE_EXTINT;
 	entry1.polarity = entry0.polarity;
 	entry1.trigger = IOAPIC_EDGE;
 	entry1.vector = 0;
@@ -2948,7 +2949,7 @@ static void mp_setup_entry(struct irq_cfg *cfg, struct mp_chip_data *data,
 			   struct IO_APIC_route_entry *entry)
 {
 	memset(entry, 0, sizeof(*entry));
-	entry->delivery_mode = apic->irq_delivery_mode;
+	entry->delivery_mode = apic->delivery_mode;
 	entry->dest_mode     = apic->irq_dest_mode;
 	entry->dest	     = cfg->dest_apicid;
 	entry->vector	     = cfg->vector;
diff --git a/arch/x86/kernel/apic/probe_32.c b/arch/x86/kernel/apic/probe_32.c
index 67b6f7c049ec..77c6e2e04a1f 100644
--- a/arch/x86/kernel/apic/probe_32.c
+++ b/arch/x86/kernel/apic/probe_32.c
@@ -69,7 +69,7 @@ static struct apic apic_default __ro_after_init = {
 	.apic_id_valid			= default_apic_id_valid,
 	.apic_id_registered		= default_apic_id_registered,
 
-	.irq_delivery_mode		= dest_Fixed,
+	.delivery_mode			= APIC_DELIVERY_MODE_FIXED,
 	/* logical delivery broadcast to all CPUs: */
 	.irq_dest_mode			= 1,
 
diff --git a/arch/x86/kernel/apic/x2apic_cluster.c b/arch/x86/kernel/apic/x2apic_cluster.c
index b0889c48a2ac..82fb43d807f7 100644
--- a/arch/x86/kernel/apic/x2apic_cluster.c
+++ b/arch/x86/kernel/apic/x2apic_cluster.c
@@ -184,7 +184,7 @@ static struct apic apic_x2apic_cluster __ro_after_init = {
 	.apic_id_valid			= x2apic_apic_id_valid,
 	.apic_id_registered		= x2apic_apic_id_registered,
 
-	.irq_delivery_mode		= dest_Fixed,
+	.delivery_mode			= APIC_DELIVERY_MODE_FIXED,
 	.irq_dest_mode			= 1, /* logical */
 
 	.disable_esr			= 0,
diff --git a/arch/x86/kernel/apic/x2apic_phys.c b/arch/x86/kernel/apic/x2apic_phys.c
index e14eae6d6ea7..437e8439db67 100644
--- a/arch/x86/kernel/apic/x2apic_phys.c
+++ b/arch/x86/kernel/apic/x2apic_phys.c
@@ -157,7 +157,7 @@ static struct apic apic_x2apic_phys __ro_after_init = {
 	.apic_id_valid			= x2apic_apic_id_valid,
 	.apic_id_registered		= x2apic_apic_id_registered,
 
-	.irq_delivery_mode		= dest_Fixed,
+	.delivery_mode			= APIC_DELIVERY_MODE_FIXED,
 	.irq_dest_mode			= 0, /* physical */
 
 	.disable_esr			= 0,
diff --git a/arch/x86/kernel/apic/x2apic_uv_x.c b/arch/x86/kernel/apic/x2apic_uv_x.c
index 9ade9e6a95ff..49deefdded68 100644
--- a/arch/x86/kernel/apic/x2apic_uv_x.c
+++ b/arch/x86/kernel/apic/x2apic_uv_x.c
@@ -703,9 +703,9 @@ static void uv_send_IPI_one(int cpu, int vector)
 	unsigned long dmode, val;
 
 	if (vector == NMI_VECTOR)
-		dmode = dest_NMI;
+		dmode = APIC_DELIVERY_MODE_NMI;
 	else
-		dmode = dest_Fixed;
+		dmode = APIC_DELIVERY_MODE_FIXED;
 
 	val = (1UL << UVH_IPI_INT_SEND_SHFT) |
 		(apicid << UVH_IPI_INT_APIC_ID_SHFT) |
@@ -807,7 +807,7 @@ static struct apic apic_x2apic_uv_x __ro_after_init = {
 	.apic_id_valid			= uv_apic_id_valid,
 	.apic_id_registered		= uv_apic_id_registered,
 
-	.irq_delivery_mode		= dest_Fixed,
+	.delivery_mode			= APIC_DELIVERY_MODE_FIXED,
 	.irq_dest_mode			= 0, /* Physical */
 
 	.disable_esr			= 0,
diff --git a/arch/x86/platform/uv/uv_irq.c b/arch/x86/platform/uv/uv_irq.c
index 18ca2261cc9a..e7020d162949 100644
--- a/arch/x86/platform/uv/uv_irq.c
+++ b/arch/x86/platform/uv/uv_irq.c
@@ -35,7 +35,7 @@ static void uv_program_mmr(struct irq_cfg *cfg, struct uv_irq_2_mmr_pnode *info)
 	mmr_value = 0;
 	entry = (struct uv_IO_APIC_route_entry *)&mmr_value;
 	entry->vector		= cfg->vector;
-	entry->delivery_mode	= apic->irq_delivery_mode;
+	entry->delivery_mode	= apic->delivery_mode;
 	entry->dest_mode	= apic->irq_dest_mode;
 	entry->polarity		= 0;
 	entry->trigger		= 0;
diff --git a/drivers/iommu/amd/iommu.c b/drivers/iommu/amd/iommu.c
index b9cf59443843..bc81b91f89fe 100644
--- a/drivers/iommu/amd/iommu.c
+++ b/drivers/iommu/amd/iommu.c
@@ -3671,7 +3671,7 @@ static void irq_remapping_prepare_irte(struct amd_ir_data *data,
 
 	data->irq_2_irte.devid = devid;
 	data->irq_2_irte.index = index + sub_handle;
-	iommu->irte_ops->prepare(data->entry, apic->irq_delivery_mode,
+	iommu->irte_ops->prepare(data->entry, apic->delivery_mode,
 				 apic->irq_dest_mode, irq_cfg->vector,
 				 irq_cfg->dest_apicid, devid);
 
@@ -3944,7 +3944,7 @@ int amd_iommu_deactivate_guest_mode(void *data)
 
 	entry->lo.fields_remap.valid       = valid;
 	entry->lo.fields_remap.dm          = apic->irq_dest_mode;
-	entry->lo.fields_remap.int_type    = apic->irq_delivery_mode;
+	entry->lo.fields_remap.int_type    = apic->delivery_mode;
 	entry->hi.fields.vector            = cfg->vector;
 	entry->lo.fields_remap.destination =
 				APICID_TO_IRTE_DEST_LO(cfg->dest_apicid);
diff --git a/drivers/iommu/intel/irq_remapping.c b/drivers/iommu/intel/irq_remapping.c
index 0cfce1d3b7bb..d44e719d1984 100644
--- a/drivers/iommu/intel/irq_remapping.c
+++ b/drivers/iommu/intel/irq_remapping.c
@@ -1122,7 +1122,7 @@ static void prepare_irte(struct irte *irte, int vector, unsigned int dest)
 	 * irq migration in the presence of interrupt-remapping.
 	*/
 	irte->trigger_mode = 0;
-	irte->dlvry_mode = apic->irq_delivery_mode;
+	irte->dlvry_mode = apic->delivery_mode;
 	irte->vector = vector;
 	irte->dest_id = IRTE_DEST(dest);
 	irte->redir_hint = 1;
diff --git a/drivers/pci/controller/pci-hyperv.c b/drivers/pci/controller/pci-hyperv.c
index 4e992403fffe..92b57ac50a06 100644
--- a/drivers/pci/controller/pci-hyperv.c
+++ b/drivers/pci/controller/pci-hyperv.c
@@ -1226,7 +1226,7 @@ static void hv_irq_unmask(struct irq_data *data)
 	params->int_target.vector = cfg->vector;
 
 	/*
-	 * Honoring apic->irq_delivery_mode set to dest_Fixed by
+	 * Honoring apic->delivery_mode set to APIC_DELIVERY_MODE_FIXED by
 	 * setting the HV_DEVICE_INTERRUPT_TARGET_MULTICAST flag results in a
 	 * spurious interrupt storm. Not doing so does not seem to have a
 	 * negative effect (yet?).
@@ -1310,7 +1310,7 @@ static u32 hv_compose_msi_req_v1(
 	int_pkt->wslot.slot = slot;
 	int_pkt->int_desc.vector = vector;
 	int_pkt->int_desc.vector_count = 1;
-	int_pkt->int_desc.delivery_mode = dest_Fixed;
+	int_pkt->int_desc.delivery_mode = APIC_DELIVERY_MODE_FIXED;
 
 	/*
 	 * Create MSI w/ dummy vCPU set, overwritten by subsequent retarget in
@@ -1331,7 +1331,7 @@ static u32 hv_compose_msi_req_v2(
 	int_pkt->wslot.slot = slot;
 	int_pkt->int_desc.vector = vector;
 	int_pkt->int_desc.vector_count = 1;
-	int_pkt->int_desc.delivery_mode = dest_Fixed;
+	int_pkt->int_desc.delivery_mode = APIC_DELIVERY_MODE_FIXED;
 
 	/*
 	 * Create MSI w/ dummy vCPU set targeting just one vCPU, overwritten
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 06/35] x86/apic: Replace pointless apic::dest_logical usage

[David Woodhouse]

From: Thomas Gleixner <tglx@linutronix.de>

All these functions are only used for logical destination mode. So reading
the destination mode mask from the apic structure is a pointless
exercise. Just hand in the proper constant: APIC_DEST_LOGICAL.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
---
 arch/x86/kernel/apic/apic_flat_64.c   | 2 +-
 arch/x86/kernel/apic/ipi.c            | 6 +++---
 arch/x86/kernel/apic/x2apic_cluster.c | 2 +-
 3 files changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/x86/kernel/apic/apic_flat_64.c b/arch/x86/kernel/apic/apic_flat_64.c
index fdd38a17f835..6df837fd5081 100644
--- a/arch/x86/kernel/apic/apic_flat_64.c
+++ b/arch/x86/kernel/apic/apic_flat_64.c
@@ -53,7 +53,7 @@ static void _flat_send_IPI_mask(unsigned long mask, int vector)
 	unsigned long flags;
 
 	local_irq_save(flags);
-	__default_send_IPI_dest_field(mask, vector, apic->dest_logical);
+	__default_send_IPI_dest_field(mask, vector, APIC_DEST_LOGICAL);
 	local_irq_restore(flags);
 }
 
diff --git a/arch/x86/kernel/apic/ipi.c b/arch/x86/kernel/apic/ipi.c
index 387154e39e08..d1fb874fbe64 100644
--- a/arch/x86/kernel/apic/ipi.c
+++ b/arch/x86/kernel/apic/ipi.c
@@ -260,7 +260,7 @@ void default_send_IPI_mask_sequence_logical(const struct cpumask *mask,
 	for_each_cpu(query_cpu, mask)
 		__default_send_IPI_dest_field(
 			early_per_cpu(x86_cpu_to_logical_apicid, query_cpu),
-			vector, apic->dest_logical);
+			vector, APIC_DEST_LOGICAL);
 	local_irq_restore(flags);
 }
 
@@ -279,7 +279,7 @@ void default_send_IPI_mask_allbutself_logical(const struct cpumask *mask,
 			continue;
 		__default_send_IPI_dest_field(
 			early_per_cpu(x86_cpu_to_logical_apicid, query_cpu),
-			vector, apic->dest_logical);
+			vector, APIC_DEST_LOGICAL);
 		}
 	local_irq_restore(flags);
 }
@@ -297,7 +297,7 @@ void default_send_IPI_mask_logical(const struct cpumask *cpumask, int vector)
 
 	local_irq_save(flags);
 	WARN_ON(mask & ~cpumask_bits(cpu_online_mask)[0]);
-	__default_send_IPI_dest_field(mask, vector, apic->dest_logical);
+	__default_send_IPI_dest_field(mask, vector, APIC_DEST_LOGICAL);
 	local_irq_restore(flags);
 }
 
diff --git a/arch/x86/kernel/apic/x2apic_cluster.c b/arch/x86/kernel/apic/x2apic_cluster.c
index 82fb43d807f7..f77e9fb7aac1 100644
--- a/arch/x86/kernel/apic/x2apic_cluster.c
+++ b/arch/x86/kernel/apic/x2apic_cluster.c
@@ -61,7 +61,7 @@ __x2apic_send_IPI_mask(const struct cpumask *mask, int vector, int apic_dest)
 		if (!dest)
 			continue;
 
-		__x2apic_send_IPI_dest(dest, vector, apic->dest_logical);
+		__x2apic_send_IPI_dest(dest, vector, APIC_DEST_LOGICAL);
 		/* Remove cluster CPUs from tmpmask */
 		cpumask_andnot(tmpmsk, tmpmsk, &cmsk->mask);
 	}
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 07/35] x86/apic: Get rid of apic::dest_logical

[David Woodhouse]

From: Thomas Gleixner <tglx@linutronix.de>

struct apic has two members which store information about the destination
mode: dest_logical and irq_dest_mode.

dest_logical contains a mask which was historically used to set the
destination mode in IPI messages. Over time the usage was reduced and the
logical/physical functions were seperated.

There are only a few places which still use 'dest_logical' but they can
ues 'irq_dest_mode' instead.

irq_dest_mode is actually a boolean where 0 means physical destination mode
and 1 means logical destination mode. Of course the name does not reflect
the functionality. This will be cleaned up in a subsequent change.

Remove apic::dest_logical and fixup the remaining users.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
---
 arch/x86/include/asm/apic.h           | 2 --
 arch/x86/kernel/apic/apic.c           | 2 +-
 arch/x86/kernel/apic/apic_flat_64.c   | 8 ++------
 arch/x86/kernel/apic/apic_noop.c      | 4 +---
 arch/x86/kernel/apic/apic_numachip.c  | 8 ++------
 arch/x86/kernel/apic/bigsmp_32.c      | 4 +---
 arch/x86/kernel/apic/probe_32.c       | 4 +---
 arch/x86/kernel/apic/x2apic_cluster.c | 4 +---
 arch/x86/kernel/apic/x2apic_phys.c    | 4 +---
 arch/x86/kernel/apic/x2apic_uv_x.c    | 4 +---
 arch/x86/kernel/smpboot.c             | 5 +++--
 arch/x86/xen/apic.c                   | 4 +---
 12 files changed, 15 insertions(+), 38 deletions(-)

diff --git a/arch/x86/include/asm/apic.h b/arch/x86/include/asm/apic.h
index 53bb62e0fdd5..019d7ac3b16e 100644
--- a/arch/x86/include/asm/apic.h
+++ b/arch/x86/include/asm/apic.h
@@ -306,8 +306,6 @@ struct apic {
 	void	(*send_IPI_all)(int vector);
 	void	(*send_IPI_self)(int vector);
 
-	/* dest_logical is used by the IPI functions */
-	u32	dest_logical;
 	u32	disable_esr;
 
 	enum apic_delivery_modes delivery_mode;
diff --git a/arch/x86/kernel/apic/apic.c b/arch/x86/kernel/apic/apic.c
index 113f6ca7b828..29d28b34cb2f 100644
--- a/arch/x86/kernel/apic/apic.c
+++ b/arch/x86/kernel/apic/apic.c
@@ -1591,7 +1591,7 @@ static void setup_local_APIC(void)
 	apic->init_apic_ldr();
 
 #ifdef CONFIG_X86_32
-	if (apic->dest_logical) {
+	if (apic->irq_dest_mode == 1) {
 		int logical_apicid, ldr_apicid;
 
 		/*
diff --git a/arch/x86/kernel/apic/apic_flat_64.c b/arch/x86/kernel/apic/apic_flat_64.c
index 6df837fd5081..bbb1b89fe711 100644
--- a/arch/x86/kernel/apic/apic_flat_64.c
+++ b/arch/x86/kernel/apic/apic_flat_64.c
@@ -117,11 +117,9 @@ static struct apic apic_flat __ro_after_init = {
 	.irq_dest_mode			= 1, /* logical */
 
 	.disable_esr			= 0,
-	.dest_logical			= APIC_DEST_LOGICAL,
-	.check_apicid_used		= NULL,
 
+	.check_apicid_used		= NULL,
 	.init_apic_ldr			= flat_init_apic_ldr,
-
 	.ioapic_phys_id_map		= NULL,
 	.setup_apic_routing		= NULL,
 	.cpu_present_to_apicid		= default_cpu_present_to_apicid,
@@ -210,11 +208,9 @@ static struct apic apic_physflat __ro_after_init = {
 	.irq_dest_mode			= 0, /* physical */
 
 	.disable_esr			= 0,
-	.dest_logical			= 0,
-	.check_apicid_used		= NULL,
 
+	.check_apicid_used		= NULL,
 	.init_apic_ldr			= physflat_init_apic_ldr,
-
 	.ioapic_phys_id_map		= NULL,
 	.setup_apic_routing		= NULL,
 	.cpu_present_to_apicid		= default_cpu_present_to_apicid,
diff --git a/arch/x86/kernel/apic/apic_noop.c b/arch/x86/kernel/apic/apic_noop.c
index 4fc934b11851..38f167ce5031 100644
--- a/arch/x86/kernel/apic/apic_noop.c
+++ b/arch/x86/kernel/apic/apic_noop.c
@@ -100,11 +100,9 @@ struct apic apic_noop __ro_after_init = {
 	.irq_dest_mode			= 1,
 
 	.disable_esr			= 0,
-	.dest_logical			= APIC_DEST_LOGICAL,
-	.check_apicid_used		= default_check_apicid_used,
 
+	.check_apicid_used		= default_check_apicid_used,
 	.init_apic_ldr			= noop_init_apic_ldr,
-
 	.ioapic_phys_id_map		= default_ioapic_phys_id_map,
 	.setup_apic_routing		= NULL,
 
diff --git a/arch/x86/kernel/apic/apic_numachip.c b/arch/x86/kernel/apic/apic_numachip.c
index db715d082ec9..4ebf9fe2c95d 100644
--- a/arch/x86/kernel/apic/apic_numachip.c
+++ b/arch/x86/kernel/apic/apic_numachip.c
@@ -250,11 +250,9 @@ static const struct apic apic_numachip1 __refconst = {
 	.irq_dest_mode			= 0, /* physical */
 
 	.disable_esr			= 0,
-	.dest_logical			= 0,
-	.check_apicid_used		= NULL,
 
+	.check_apicid_used		= NULL,
 	.init_apic_ldr			= flat_init_apic_ldr,
-
 	.ioapic_phys_id_map		= NULL,
 	.setup_apic_routing		= NULL,
 	.cpu_present_to_apicid		= default_cpu_present_to_apicid,
@@ -299,11 +297,9 @@ static const struct apic apic_numachip2 __refconst = {
 	.irq_dest_mode			= 0, /* physical */
 
 	.disable_esr			= 0,
-	.dest_logical			= 0,
-	.check_apicid_used		= NULL,
 
+	.check_apicid_used		= NULL,
 	.init_apic_ldr			= flat_init_apic_ldr,
-
 	.ioapic_phys_id_map		= NULL,
 	.setup_apic_routing		= NULL,
 	.cpu_present_to_apicid		= default_cpu_present_to_apicid,
diff --git a/arch/x86/kernel/apic/bigsmp_32.c b/arch/x86/kernel/apic/bigsmp_32.c
index 7f6461f5d349..64c375b8c54e 100644
--- a/arch/x86/kernel/apic/bigsmp_32.c
+++ b/arch/x86/kernel/apic/bigsmp_32.c
@@ -132,11 +132,9 @@ static struct apic apic_bigsmp __ro_after_init = {
 	.irq_dest_mode			= 0,
 
 	.disable_esr			= 1,
-	.dest_logical			= 0,
-	.check_apicid_used		= bigsmp_check_apicid_used,
 
+	.check_apicid_used		= bigsmp_check_apicid_used,
 	.init_apic_ldr			= bigsmp_init_apic_ldr,
-
 	.ioapic_phys_id_map		= bigsmp_ioapic_phys_id_map,
 	.setup_apic_routing		= bigsmp_setup_apic_routing,
 	.cpu_present_to_apicid		= bigsmp_cpu_present_to_apicid,
diff --git a/arch/x86/kernel/apic/probe_32.c b/arch/x86/kernel/apic/probe_32.c
index 77c6e2e04a1f..97652aacf3e1 100644
--- a/arch/x86/kernel/apic/probe_32.c
+++ b/arch/x86/kernel/apic/probe_32.c
@@ -74,11 +74,9 @@ static struct apic apic_default __ro_after_init = {
 	.irq_dest_mode			= 1,
 
 	.disable_esr			= 0,
-	.dest_logical			= APIC_DEST_LOGICAL,
-	.check_apicid_used		= default_check_apicid_used,
 
+	.check_apicid_used		= default_check_apicid_used,
 	.init_apic_ldr			= default_init_apic_ldr,
-
 	.ioapic_phys_id_map		= default_ioapic_phys_id_map,
 	.setup_apic_routing		= setup_apic_flat_routing,
 	.cpu_present_to_apicid		= default_cpu_present_to_apicid,
diff --git a/arch/x86/kernel/apic/x2apic_cluster.c b/arch/x86/kernel/apic/x2apic_cluster.c
index f77e9fb7aac1..53390fc9f51e 100644
--- a/arch/x86/kernel/apic/x2apic_cluster.c
+++ b/arch/x86/kernel/apic/x2apic_cluster.c
@@ -188,11 +188,9 @@ static struct apic apic_x2apic_cluster __ro_after_init = {
 	.irq_dest_mode			= 1, /* logical */
 
 	.disable_esr			= 0,
-	.dest_logical			= APIC_DEST_LOGICAL,
-	.check_apicid_used		= NULL,
 
+	.check_apicid_used		= NULL,
 	.init_apic_ldr			= init_x2apic_ldr,
-
 	.ioapic_phys_id_map		= NULL,
 	.setup_apic_routing		= NULL,
 	.cpu_present_to_apicid		= default_cpu_present_to_apicid,
diff --git a/arch/x86/kernel/apic/x2apic_phys.c b/arch/x86/kernel/apic/x2apic_phys.c
index 437e8439db67..ee0c4d08092c 100644
--- a/arch/x86/kernel/apic/x2apic_phys.c
+++ b/arch/x86/kernel/apic/x2apic_phys.c
@@ -161,11 +161,9 @@ static struct apic apic_x2apic_phys __ro_after_init = {
 	.irq_dest_mode			= 0, /* physical */
 
 	.disable_esr			= 0,
-	.dest_logical			= 0,
-	.check_apicid_used		= NULL,
 
+	.check_apicid_used		= NULL,
 	.init_apic_ldr			= init_x2apic_ldr,
-
 	.ioapic_phys_id_map		= NULL,
 	.setup_apic_routing		= NULL,
 	.cpu_present_to_apicid		= default_cpu_present_to_apicid,
diff --git a/arch/x86/kernel/apic/x2apic_uv_x.c b/arch/x86/kernel/apic/x2apic_uv_x.c
index 49deefdded68..d21a6853afee 100644
--- a/arch/x86/kernel/apic/x2apic_uv_x.c
+++ b/arch/x86/kernel/apic/x2apic_uv_x.c
@@ -811,11 +811,9 @@ static struct apic apic_x2apic_uv_x __ro_after_init = {
 	.irq_dest_mode			= 0, /* Physical */
 
 	.disable_esr			= 0,
-	.dest_logical			= APIC_DEST_PHYSICAL,
-	.check_apicid_used		= NULL,
 
+	.check_apicid_used		= NULL,
 	.init_apic_ldr			= uv_init_apic_ldr,
-
 	.ioapic_phys_id_map		= NULL,
 	.setup_apic_routing		= NULL,
 	.cpu_present_to_apicid		= default_cpu_present_to_apicid,
diff --git a/arch/x86/kernel/smpboot.c b/arch/x86/kernel/smpboot.c
index de776b2e6046..6c14f1091f60 100644
--- a/arch/x86/kernel/smpboot.c
+++ b/arch/x86/kernel/smpboot.c
@@ -747,13 +747,14 @@ static void __init smp_quirk_init_udelay(void)
 int
 wakeup_secondary_cpu_via_nmi(int apicid, unsigned long start_eip)
 {
+	u32 dm = apic->irq_dest_mode ? APIC_DEST_LOGICAL : APIC_DEST_PHYSICAL;
 	unsigned long send_status, accept_status = 0;
 	int maxlvt;
 
 	/* Target chip */
 	/* Boot on the stack */
 	/* Kick the second */
-	apic_icr_write(APIC_DM_NMI | apic->dest_logical, apicid);
+	apic_icr_write(APIC_DM_NMI | dm, apicid);
 
 	pr_debug("Waiting for send to finish...\n");
 	send_status = safe_apic_wait_icr_idle();
@@ -980,7 +981,7 @@ wakeup_cpu_via_init_nmi(int cpu, unsigned long start_ip, int apicid,
 	if (!boot_error) {
 		enable_start_cpu0 = 1;
 		*cpu0_nmi_registered = 1;
-		if (apic->dest_logical == APIC_DEST_LOGICAL)
+		if (apic->irq_dest_mode)
 			id = cpu0_logical_apicid;
 		else
 			id = apicid;
diff --git a/arch/x86/xen/apic.c b/arch/x86/xen/apic.c
index e82fd1910dae..c35c24b5bc01 100644
--- a/arch/x86/xen/apic.c
+++ b/arch/x86/xen/apic.c
@@ -152,11 +152,9 @@ static struct apic xen_pv_apic = {
 	/* .irq_dest_mode     - used in native_compose_msi_msg only */
 
 	.disable_esr			= 0,
-	/* .dest_logical      -  default_send_IPI_ use it but we use our own. */
-	.check_apicid_used		= default_check_apicid_used, /* Used on 32-bit */
 
+	.check_apicid_used		= default_check_apicid_used, /* Used on 32-bit */
 	.init_apic_ldr			= xen_noop, /* setup_local_APIC calls it */
-
 	.ioapic_phys_id_map		= default_ioapic_phys_id_map, /* Used on 32-bit */
 	.setup_apic_routing		= NULL,
 	.cpu_present_to_apicid		= xen_cpu_present_to_apicid,
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 08/35] x86/apic: Cleanup destination mode

[David Woodhouse]

From: Thomas Gleixner <tglx@linutronix.de>

apic::irq_dest_mode is actually a boolean, but defined as u32 and named in
a way which does not explain what it means.

Make it a boolean and rename it to 'dest_mode_logical'

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
---
 arch/x86/include/asm/apic.h           | 2 +-
 arch/x86/kernel/apic/apic.c           | 2 +-
 arch/x86/kernel/apic/apic_flat_64.c   | 4 ++--
 arch/x86/kernel/apic/apic_noop.c      | 4 +---
 arch/x86/kernel/apic/apic_numachip.c  | 4 ++--
 arch/x86/kernel/apic/bigsmp_32.c      | 3 +--
 arch/x86/kernel/apic/io_apic.c        | 2 +-
 arch/x86/kernel/apic/msi.c            | 6 +++---
 arch/x86/kernel/apic/probe_32.c       | 3 +--
 arch/x86/kernel/apic/x2apic_cluster.c | 2 +-
 arch/x86/kernel/apic/x2apic_phys.c    | 2 +-
 arch/x86/kernel/apic/x2apic_uv_x.c    | 2 +-
 arch/x86/kernel/smpboot.c             | 7 ++-----
 arch/x86/platform/uv/uv_irq.c         | 2 +-
 arch/x86/xen/apic.c                   | 3 +--
 drivers/iommu/amd/amd_iommu_types.h   | 2 +-
 drivers/iommu/amd/iommu.c             | 8 ++++----
 drivers/iommu/intel/irq_remapping.c   | 2 +-
 18 files changed, 26 insertions(+), 34 deletions(-)

diff --git a/arch/x86/include/asm/apic.h b/arch/x86/include/asm/apic.h
index 019d7ac3b16e..652f62252349 100644
--- a/arch/x86/include/asm/apic.h
+++ b/arch/x86/include/asm/apic.h
@@ -309,7 +309,7 @@ struct apic {
 	u32	disable_esr;
 
 	enum apic_delivery_modes delivery_mode;
-	u32	irq_dest_mode;
+	bool	dest_mode_logical;
 
 	u32	(*calc_dest_apicid)(unsigned int cpu);
 
diff --git a/arch/x86/kernel/apic/apic.c b/arch/x86/kernel/apic/apic.c
index 29d28b34cb2f..54f04355aaa2 100644
--- a/arch/x86/kernel/apic/apic.c
+++ b/arch/x86/kernel/apic/apic.c
@@ -1591,7 +1591,7 @@ static void setup_local_APIC(void)
 	apic->init_apic_ldr();
 
 #ifdef CONFIG_X86_32
-	if (apic->irq_dest_mode == 1) {
+	if (apic->dest_mode_logical) {
 		int logical_apicid, ldr_apicid;
 
 		/*
diff --git a/arch/x86/kernel/apic/apic_flat_64.c b/arch/x86/kernel/apic/apic_flat_64.c
index bbb1b89fe711..8f72b4351c9f 100644
--- a/arch/x86/kernel/apic/apic_flat_64.c
+++ b/arch/x86/kernel/apic/apic_flat_64.c
@@ -114,7 +114,7 @@ static struct apic apic_flat __ro_after_init = {
 	.apic_id_registered		= flat_apic_id_registered,
 
 	.delivery_mode			= APIC_DELIVERY_MODE_FIXED,
-	.irq_dest_mode			= 1, /* logical */
+	.dest_mode_logical		= true,
 
 	.disable_esr			= 0,
 
@@ -205,7 +205,7 @@ static struct apic apic_physflat __ro_after_init = {
 	.apic_id_registered		= flat_apic_id_registered,
 
 	.delivery_mode			= APIC_DELIVERY_MODE_FIXED,
-	.irq_dest_mode			= 0, /* physical */
+	.dest_mode_logical		= false,
 
 	.disable_esr			= 0,
 
diff --git a/arch/x86/kernel/apic/apic_noop.c b/arch/x86/kernel/apic/apic_noop.c
index 38f167ce5031..fe78319e0f7a 100644
--- a/arch/x86/kernel/apic/apic_noop.c
+++ b/arch/x86/kernel/apic/apic_noop.c
@@ -96,8 +96,7 @@ struct apic apic_noop __ro_after_init = {
 	.apic_id_registered		= noop_apic_id_registered,
 
 	.delivery_mode			= APIC_DELIVERY_MODE_FIXED,
-	/* logical delivery broadcast to all CPUs: */
-	.irq_dest_mode			= 1,
+	.dest_mode_logical		= true,
 
 	.disable_esr			= 0,
 
@@ -105,7 +104,6 @@ struct apic apic_noop __ro_after_init = {
 	.init_apic_ldr			= noop_init_apic_ldr,
 	.ioapic_phys_id_map		= default_ioapic_phys_id_map,
 	.setup_apic_routing		= NULL,
-
 	.cpu_present_to_apicid		= default_cpu_present_to_apicid,
 	.apicid_to_cpu_present		= physid_set_mask_of_physid,
 
diff --git a/arch/x86/kernel/apic/apic_numachip.c b/arch/x86/kernel/apic/apic_numachip.c
index 4ebf9fe2c95d..a54d817eb4b6 100644
--- a/arch/x86/kernel/apic/apic_numachip.c
+++ b/arch/x86/kernel/apic/apic_numachip.c
@@ -247,7 +247,7 @@ static const struct apic apic_numachip1 __refconst = {
 	.apic_id_registered		= numachip_apic_id_registered,
 
 	.delivery_mode			= APIC_DELIVERY_MODE_FIXED,
-	.irq_dest_mode			= 0, /* physical */
+	.dest_mode_logical		= false,
 
 	.disable_esr			= 0,
 
@@ -294,7 +294,7 @@ static const struct apic apic_numachip2 __refconst = {
 	.apic_id_registered		= numachip_apic_id_registered,
 
 	.delivery_mode			= APIC_DELIVERY_MODE_FIXED,
-	.irq_dest_mode			= 0, /* physical */
+	.dest_mode_logical		= false,
 
 	.disable_esr			= 0,
 
diff --git a/arch/x86/kernel/apic/bigsmp_32.c b/arch/x86/kernel/apic/bigsmp_32.c
index 64c375b8c54e..77555f66c14d 100644
--- a/arch/x86/kernel/apic/bigsmp_32.c
+++ b/arch/x86/kernel/apic/bigsmp_32.c
@@ -128,8 +128,7 @@ static struct apic apic_bigsmp __ro_after_init = {
 	.apic_id_registered		= bigsmp_apic_id_registered,
 
 	.delivery_mode			= APIC_DELIVERY_MODE_FIXED,
-	/* phys delivery to target CPU: */
-	.irq_dest_mode			= 0,
+	.dest_mode_logical		= false,
 
 	.disable_esr			= 1,
 
diff --git a/arch/x86/kernel/apic/io_apic.c b/arch/x86/kernel/apic/io_apic.c
index cff6cbc3d183..c6d92d2570d0 100644
--- a/arch/x86/kernel/apic/io_apic.c
+++ b/arch/x86/kernel/apic/io_apic.c
@@ -2950,7 +2950,7 @@ static void mp_setup_entry(struct irq_cfg *cfg, struct mp_chip_data *data,
 {
 	memset(entry, 0, sizeof(*entry));
 	entry->delivery_mode = apic->delivery_mode;
-	entry->dest_mode     = apic->irq_dest_mode;
+	entry->dest_mode     = apic->dest_mode_logical;
 	entry->dest	     = cfg->dest_apicid;
 	entry->vector	     = cfg->vector;
 	entry->trigger	     = data->trigger;
diff --git a/arch/x86/kernel/apic/msi.c b/arch/x86/kernel/apic/msi.c
index 516df47bde73..46ffd41a4238 100644
--- a/arch/x86/kernel/apic/msi.c
+++ b/arch/x86/kernel/apic/msi.c
@@ -30,9 +30,9 @@ static void __irq_msi_compose_msg(struct irq_cfg *cfg, struct msi_msg *msg,
 
 	msg->address_lo =
 		MSI_ADDR_BASE_LO |
-		((apic->irq_dest_mode == 0) ?
-			MSI_ADDR_DEST_MODE_PHYSICAL :
-			MSI_ADDR_DEST_MODE_LOGICAL) |
+		(apic->dest_mode_logical ?
+			MSI_ADDR_DEST_MODE_LOGICAL :
+			MSI_ADDR_DEST_MODE_PHYSICAL) |
 		MSI_ADDR_REDIRECTION_CPU |
 		MSI_ADDR_DEST_ID(cfg->dest_apicid);
 
diff --git a/arch/x86/kernel/apic/probe_32.c b/arch/x86/kernel/apic/probe_32.c
index 97652aacf3e1..a61f642b1b90 100644
--- a/arch/x86/kernel/apic/probe_32.c
+++ b/arch/x86/kernel/apic/probe_32.c
@@ -70,8 +70,7 @@ static struct apic apic_default __ro_after_init = {
 	.apic_id_registered		= default_apic_id_registered,
 
 	.delivery_mode			= APIC_DELIVERY_MODE_FIXED,
-	/* logical delivery broadcast to all CPUs: */
-	.irq_dest_mode			= 1,
+	.dest_mode_logical		= true,
 
 	.disable_esr			= 0,
 
diff --git a/arch/x86/kernel/apic/x2apic_cluster.c b/arch/x86/kernel/apic/x2apic_cluster.c
index 53390fc9f51e..df6adc5674c9 100644
--- a/arch/x86/kernel/apic/x2apic_cluster.c
+++ b/arch/x86/kernel/apic/x2apic_cluster.c
@@ -185,7 +185,7 @@ static struct apic apic_x2apic_cluster __ro_after_init = {
 	.apic_id_registered		= x2apic_apic_id_registered,
 
 	.delivery_mode			= APIC_DELIVERY_MODE_FIXED,
-	.irq_dest_mode			= 1, /* logical */
+	.dest_mode_logical		= true,
 
 	.disable_esr			= 0,
 
diff --git a/arch/x86/kernel/apic/x2apic_phys.c b/arch/x86/kernel/apic/x2apic_phys.c
index ee0c4d08092c..0e4e81971567 100644
--- a/arch/x86/kernel/apic/x2apic_phys.c
+++ b/arch/x86/kernel/apic/x2apic_phys.c
@@ -158,7 +158,7 @@ static struct apic apic_x2apic_phys __ro_after_init = {
 	.apic_id_registered		= x2apic_apic_id_registered,
 
 	.delivery_mode			= APIC_DELIVERY_MODE_FIXED,
-	.irq_dest_mode			= 0, /* physical */
+	.dest_mode_logical		= false,
 
 	.disable_esr			= 0,
 
diff --git a/arch/x86/kernel/apic/x2apic_uv_x.c b/arch/x86/kernel/apic/x2apic_uv_x.c
index d21a6853afee..de94181f4d0c 100644
--- a/arch/x86/kernel/apic/x2apic_uv_x.c
+++ b/arch/x86/kernel/apic/x2apic_uv_x.c
@@ -808,7 +808,7 @@ static struct apic apic_x2apic_uv_x __ro_after_init = {
 	.apic_id_registered		= uv_apic_id_registered,
 
 	.delivery_mode			= APIC_DELIVERY_MODE_FIXED,
-	.irq_dest_mode			= 0, /* Physical */
+	.dest_mode_logical		= false,
 
 	.disable_esr			= 0,
 
diff --git a/arch/x86/kernel/smpboot.c b/arch/x86/kernel/smpboot.c
index 6c14f1091f60..d133d6580f41 100644
--- a/arch/x86/kernel/smpboot.c
+++ b/arch/x86/kernel/smpboot.c
@@ -747,7 +747,7 @@ static void __init smp_quirk_init_udelay(void)
 int
 wakeup_secondary_cpu_via_nmi(int apicid, unsigned long start_eip)
 {
-	u32 dm = apic->irq_dest_mode ? APIC_DEST_LOGICAL : APIC_DEST_PHYSICAL;
+	u32 dm = apic->dest_mode_logical ? APIC_DEST_LOGICAL : APIC_DEST_PHYSICAL;
 	unsigned long send_status, accept_status = 0;
 	int maxlvt;
 
@@ -981,10 +981,7 @@ wakeup_cpu_via_init_nmi(int cpu, unsigned long start_ip, int apicid,
 	if (!boot_error) {
 		enable_start_cpu0 = 1;
 		*cpu0_nmi_registered = 1;
-		if (apic->irq_dest_mode)
-			id = cpu0_logical_apicid;
-		else
-			id = apicid;
+		id = apic->dest_mode_logical ? cpu0_logical_apicid : apicid;
 		boot_error = wakeup_secondary_cpu_via_nmi(id, start_ip);
 	}
 
diff --git a/arch/x86/platform/uv/uv_irq.c b/arch/x86/platform/uv/uv_irq.c
index e7020d162949..1a536a187d74 100644
--- a/arch/x86/platform/uv/uv_irq.c
+++ b/arch/x86/platform/uv/uv_irq.c
@@ -36,7 +36,7 @@ static void uv_program_mmr(struct irq_cfg *cfg, struct uv_irq_2_mmr_pnode *info)
 	entry = (struct uv_IO_APIC_route_entry *)&mmr_value;
 	entry->vector		= cfg->vector;
 	entry->delivery_mode	= apic->delivery_mode;
-	entry->dest_mode	= apic->irq_dest_mode;
+	entry->dest_mode	= apic->dest_mode_logical;
 	entry->polarity		= 0;
 	entry->trigger		= 0;
 	entry->mask		= 0;
diff --git a/arch/x86/xen/apic.c b/arch/x86/xen/apic.c
index c35c24b5bc01..0d46cc283cf5 100644
--- a/arch/x86/xen/apic.c
+++ b/arch/x86/xen/apic.c
@@ -148,8 +148,7 @@ static struct apic xen_pv_apic = {
 	.apic_id_valid 			= xen_id_always_valid,
 	.apic_id_registered 		= xen_id_always_registered,
 
-	/* .irq_delivery_mode - used in native_compose_msi_msg only */
-	/* .irq_dest_mode     - used in native_compose_msi_msg only */
+	/* .delivery_mode and .dest_mode_logical not used by XENPV */
 
 	.disable_esr			= 0,
 
diff --git a/drivers/iommu/amd/amd_iommu_types.h b/drivers/iommu/amd/amd_iommu_types.h
index f696ac7c5f89..ba74a722a400 100644
--- a/drivers/iommu/amd/amd_iommu_types.h
+++ b/drivers/iommu/amd/amd_iommu_types.h
@@ -893,7 +893,7 @@ struct amd_ir_data {
 };
 
 struct amd_irte_ops {
-	void (*prepare)(void *, u32, u32, u8, u32, int);
+	void (*prepare)(void *, u32, bool, u8, u32, int);
 	void (*activate)(void *, u16, u16);
 	void (*deactivate)(void *, u16, u16);
 	void (*set_affinity)(void *, u16, u16, u8, u32);
diff --git a/drivers/iommu/amd/iommu.c b/drivers/iommu/amd/iommu.c
index bc81b91f89fe..d7f0c8908602 100644
--- a/drivers/iommu/amd/iommu.c
+++ b/drivers/iommu/amd/iommu.c
@@ -3466,7 +3466,7 @@ static void free_irte(u16 devid, int index)
 }
 
 static void irte_prepare(void *entry,
-			 u32 delivery_mode, u32 dest_mode,
+			 u32 delivery_mode, bool dest_mode,
 			 u8 vector, u32 dest_apicid, int devid)
 {
 	union irte *irte = (union irte *) entry;
@@ -3480,7 +3480,7 @@ static void irte_prepare(void *entry,
 }
 
 static void irte_ga_prepare(void *entry,
-			    u32 delivery_mode, u32 dest_mode,
+			    u32 delivery_mode, bool dest_mode,
 			    u8 vector, u32 dest_apicid, int devid)
 {
 	struct irte_ga *irte = (struct irte_ga *) entry;
@@ -3672,7 +3672,7 @@ static void irq_remapping_prepare_irte(struct amd_ir_data *data,
 	data->irq_2_irte.devid = devid;
 	data->irq_2_irte.index = index + sub_handle;
 	iommu->irte_ops->prepare(data->entry, apic->delivery_mode,
-				 apic->irq_dest_mode, irq_cfg->vector,
+				 apic->dest_mode_logical, irq_cfg->vector,
 				 irq_cfg->dest_apicid, devid);
 
 	switch (info->type) {
@@ -3943,7 +3943,7 @@ int amd_iommu_deactivate_guest_mode(void *data)
 	entry->hi.val = 0;
 
 	entry->lo.fields_remap.valid       = valid;
-	entry->lo.fields_remap.dm          = apic->irq_dest_mode;
+	entry->lo.fields_remap.dm          = apic->dest_mode_logical;
 	entry->lo.fields_remap.int_type    = apic->delivery_mode;
 	entry->hi.fields.vector            = cfg->vector;
 	entry->lo.fields_remap.destination =
diff --git a/drivers/iommu/intel/irq_remapping.c b/drivers/iommu/intel/irq_remapping.c
index d44e719d1984..5628d43b795e 100644
--- a/drivers/iommu/intel/irq_remapping.c
+++ b/drivers/iommu/intel/irq_remapping.c
@@ -1113,7 +1113,7 @@ static void prepare_irte(struct irte *irte, int vector, unsigned int dest)
 	memset(irte, 0, sizeof(*irte));
 
 	irte->present = 1;
-	irte->dst_mode = apic->irq_dest_mode;
+	irte->dst_mode = apic->dest_mode_logical;
 	/*
 	 * Trigger mode in the IRTE will always be edge, and for IO-APIC, the
 	 * actual level or edge trigger will be setup in the IO-APIC
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 09/35] x86/apic: Always provide irq_compose_msi_msg() method for vector domain

[David Woodhouse]

From: David Woodhouse <dwmw@amazon.co.uk>

This shouldn't be dependent on PCI_MSI. HPET and I/O-APIC can deliver
interrupts through MSI without having any PCI in the system at all.

Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
---
 arch/x86/include/asm/apic.h   |  8 +++-----
 arch/x86/kernel/apic/apic.c   | 32 ++++++++++++++++++++++++++++++
 arch/x86/kernel/apic/msi.c    | 37 -----------------------------------
 arch/x86/kernel/apic/vector.c |  6 ++++++
 4 files changed, 41 insertions(+), 42 deletions(-)

diff --git a/arch/x86/include/asm/apic.h b/arch/x86/include/asm/apic.h
index 652f62252349..b489bb9894ae 100644
--- a/arch/x86/include/asm/apic.h
+++ b/arch/x86/include/asm/apic.h
@@ -520,12 +520,10 @@ static inline void apic_smt_update(void) { }
 #endif
 
 struct msi_msg;
+struct irq_cfg;
 
-#ifdef CONFIG_PCI_MSI
-void x86_vector_msi_compose_msg(struct irq_data *data, struct msi_msg *msg);
-#else
-# define x86_vector_msi_compose_msg NULL
-#endif
+extern void __irq_msi_compose_msg(struct irq_cfg *cfg, struct msi_msg *msg,
+				  bool dmar);
 
 extern void ioapic_zap_locks(void);
 
diff --git a/arch/x86/kernel/apic/apic.c b/arch/x86/kernel/apic/apic.c
index 54f04355aaa2..4c15bf29ea2c 100644
--- a/arch/x86/kernel/apic/apic.c
+++ b/arch/x86/kernel/apic/apic.c
@@ -50,6 +50,7 @@
 #include <asm/io_apic.h>
 #include <asm/desc.h>
 #include <asm/hpet.h>
+#include <asm/msidef.h>
 #include <asm/mtrr.h>
 #include <asm/time.h>
 #include <asm/smp.h>
@@ -2480,6 +2481,37 @@ int hard_smp_processor_id(void)
 	return read_apic_id();
 }
 
+void __irq_msi_compose_msg(struct irq_cfg *cfg, struct msi_msg *msg,
+			   bool dmar)
+{
+	msg->address_hi = MSI_ADDR_BASE_HI;
+
+	msg->address_lo =
+		MSI_ADDR_BASE_LO |
+		(apic->dest_mode_logical ?
+			MSI_ADDR_DEST_MODE_LOGICAL :
+			MSI_ADDR_DEST_MODE_PHYSICAL) |
+		MSI_ADDR_REDIRECTION_CPU |
+		MSI_ADDR_DEST_ID(cfg->dest_apicid);
+
+	msg->data =
+		MSI_DATA_TRIGGER_EDGE |
+		MSI_DATA_LEVEL_ASSERT |
+		MSI_DATA_DELIVERY_FIXED |
+		MSI_DATA_VECTOR(cfg->vector);
+
+	/*
+	 * Only the IOMMU itself can use the trick of putting destination
+	 * APIC ID into the high bits of the address. Anything else would
+	 * just be writing to memory if it tried that, and needs IR to
+	 * address higher APIC IDs.
+	 */
+	if (dmar)
+		msg->address_hi |= MSI_ADDR_EXT_DEST_ID(cfg->dest_apicid);
+	else
+		WARN_ON_ONCE(MSI_ADDR_EXT_DEST_ID(cfg->dest_apicid));
+}
+
 /*
  * Override the generic EOI implementation with an optimized version.
  * Only called during early boot when only one CPU is active and with
diff --git a/arch/x86/kernel/apic/msi.c b/arch/x86/kernel/apic/msi.c
index 46ffd41a4238..4eda617eda1e 100644
--- a/arch/x86/kernel/apic/msi.c
+++ b/arch/x86/kernel/apic/msi.c
@@ -15,7 +15,6 @@
 #include <linux/hpet.h>
 #include <linux/msi.h>
 #include <asm/irqdomain.h>
-#include <asm/msidef.h>
 #include <asm/hpet.h>
 #include <asm/hw_irq.h>
 #include <asm/apic.h>
@@ -23,42 +22,6 @@
 
 struct irq_domain *x86_pci_msi_default_domain __ro_after_init;
 
-static void __irq_msi_compose_msg(struct irq_cfg *cfg, struct msi_msg *msg,
-				  bool dmar)
-{
-	msg->address_hi = MSI_ADDR_BASE_HI;
-
-	msg->address_lo =
-		MSI_ADDR_BASE_LO |
-		(apic->dest_mode_logical ?
-			MSI_ADDR_DEST_MODE_LOGICAL :
-			MSI_ADDR_DEST_MODE_PHYSICAL) |
-		MSI_ADDR_REDIRECTION_CPU |
-		MSI_ADDR_DEST_ID(cfg->dest_apicid);
-
-	msg->data =
-		MSI_DATA_TRIGGER_EDGE |
-		MSI_DATA_LEVEL_ASSERT |
-		MSI_DATA_DELIVERY_FIXED |
-		MSI_DATA_VECTOR(cfg->vector);
-
-	/*
-	 * Only the IOMMU itself can use the trick of putting destination
-	 * APIC ID into the high bits of the address. Anything else would
-	 * just be writing to memory if it tried that, and needs IR to
-	 * address higher APIC IDs.
-	 */
-	if (dmar)
-		msg->address_hi |= MSI_ADDR_EXT_DEST_ID(cfg->dest_apicid);
-	else
-		WARN_ON_ONCE(MSI_ADDR_EXT_DEST_ID(cfg->dest_apicid));
-}
-
-void x86_vector_msi_compose_msg(struct irq_data *data, struct msi_msg *msg)
-{
-	__irq_msi_compose_msg(irqd_cfg(data), msg, false);
-}
-
 static void irq_msi_update_msg(struct irq_data *irqd, struct irq_cfg *cfg)
 {
 	struct msi_msg msg[2] = { [1] = { }, };
diff --git a/arch/x86/kernel/apic/vector.c b/arch/x86/kernel/apic/vector.c
index 1eac53632786..bb2e2a2488a5 100644
--- a/arch/x86/kernel/apic/vector.c
+++ b/arch/x86/kernel/apic/vector.c
@@ -818,6 +818,12 @@ void apic_ack_edge(struct irq_data *irqd)
 	apic_ack_irq(irqd);
 }
 
+static void x86_vector_msi_compose_msg(struct irq_data *data,
+				       struct msi_msg *msg)
+{
+       __irq_msi_compose_msg(irqd_cfg(data), msg, false);
+}
+
 static struct irq_chip lapic_controller = {
 	.name			= "APIC",
 	.irq_ack		= apic_ack_edge,
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 10/35] x86/hpet: Move MSI support into hpet.c

[David Woodhouse]

From: David Woodhouse <dwmw@amazon.co.uk>

This isn't really dependent on PCI MSI; it's just generic MSI which is now
supported by the generic x86_vector_domain. Move the HPET MSI support back
into hpet.c with the rest of the HPET support.

Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
---
 arch/x86/include/asm/hpet.h |  11 ----
 arch/x86/kernel/apic/msi.c  | 111 ---------------------------------
 arch/x86/kernel/hpet.c      | 118 ++++++++++++++++++++++++++++++++++--
 3 files changed, 112 insertions(+), 128 deletions(-)

diff --git a/arch/x86/include/asm/hpet.h b/arch/x86/include/asm/hpet.h
index 6352dee37cda..ab9f3dd87c80 100644
--- a/arch/x86/include/asm/hpet.h
+++ b/arch/x86/include/asm/hpet.h
@@ -74,17 +74,6 @@ extern void hpet_disable(void);
 extern unsigned int hpet_readl(unsigned int a);
 extern void force_hpet_resume(void);
 
-struct irq_data;
-struct hpet_channel;
-struct irq_domain;
-
-extern void hpet_msi_unmask(struct irq_data *data);
-extern void hpet_msi_mask(struct irq_data *data);
-extern void hpet_msi_write(struct hpet_channel *hc, struct msi_msg *msg);
-extern struct irq_domain *hpet_create_irq_domain(int hpet_id);
-extern int hpet_assign_irq(struct irq_domain *domain,
-			   struct hpet_channel *hc, int dev_num);
-
 #ifdef CONFIG_HPET_EMULATE_RTC
 
 #include <linux/interrupt.h>
diff --git a/arch/x86/kernel/apic/msi.c b/arch/x86/kernel/apic/msi.c
index 4eda617eda1e..44ebe25e7703 100644
--- a/arch/x86/kernel/apic/msi.c
+++ b/arch/x86/kernel/apic/msi.c
@@ -340,114 +340,3 @@ void dmar_free_hwirq(int irq)
 	irq_domain_free_irqs(irq, 1);
 }
 #endif
-
-/*
- * MSI message composition
- */
-#ifdef CONFIG_HPET_TIMER
-static inline int hpet_dev_id(struct irq_domain *domain)
-{
-	struct msi_domain_info *info = msi_get_domain_info(domain);
-
-	return (int)(long)info->data;
-}
-
-static void hpet_msi_write_msg(struct irq_data *data, struct msi_msg *msg)
-{
-	hpet_msi_write(irq_data_get_irq_handler_data(data), msg);
-}
-
-static struct irq_chip hpet_msi_controller __ro_after_init = {
-	.name = "HPET-MSI",
-	.irq_unmask = hpet_msi_unmask,
-	.irq_mask = hpet_msi_mask,
-	.irq_ack = irq_chip_ack_parent,
-	.irq_set_affinity = msi_domain_set_affinity,
-	.irq_retrigger = irq_chip_retrigger_hierarchy,
-	.irq_write_msi_msg = hpet_msi_write_msg,
-	.flags = IRQCHIP_SKIP_SET_WAKE,
-};
-
-static int hpet_msi_init(struct irq_domain *domain,
-			 struct msi_domain_info *info, unsigned int virq,
-			 irq_hw_number_t hwirq, msi_alloc_info_t *arg)
-{
-	irq_set_status_flags(virq, IRQ_MOVE_PCNTXT);
-	irq_domain_set_info(domain, virq, arg->hwirq, info->chip, NULL,
-			    handle_edge_irq, arg->data, "edge");
-
-	return 0;
-}
-
-static void hpet_msi_free(struct irq_domain *domain,
-			  struct msi_domain_info *info, unsigned int virq)
-{
-	irq_clear_status_flags(virq, IRQ_MOVE_PCNTXT);
-}
-
-static struct msi_domain_ops hpet_msi_domain_ops = {
-	.msi_init	= hpet_msi_init,
-	.msi_free	= hpet_msi_free,
-};
-
-static struct msi_domain_info hpet_msi_domain_info = {
-	.ops		= &hpet_msi_domain_ops,
-	.chip		= &hpet_msi_controller,
-	.flags		= MSI_FLAG_USE_DEF_DOM_OPS,
-};
-
-struct irq_domain *hpet_create_irq_domain(int hpet_id)
-{
-	struct msi_domain_info *domain_info;
-	struct irq_domain *parent, *d;
-	struct irq_alloc_info info;
-	struct fwnode_handle *fn;
-
-	if (x86_vector_domain == NULL)
-		return NULL;
-
-	domain_info = kzalloc(sizeof(*domain_info), GFP_KERNEL);
-	if (!domain_info)
-		return NULL;
-
-	*domain_info = hpet_msi_domain_info;
-	domain_info->data = (void *)(long)hpet_id;
-
-	init_irq_alloc_info(&info, NULL);
-	info.type = X86_IRQ_ALLOC_TYPE_HPET_GET_PARENT;
-	info.devid = hpet_id;
-	parent = irq_remapping_get_irq_domain(&info);
-	if (parent == NULL)
-		parent = x86_vector_domain;
-	else
-		hpet_msi_controller.name = "IR-HPET-MSI";
-
-	fn = irq_domain_alloc_named_id_fwnode(hpet_msi_controller.name,
-					      hpet_id);
-	if (!fn) {
-		kfree(domain_info);
-		return NULL;
-	}
-
-	d = msi_create_irq_domain(fn, domain_info, parent);
-	if (!d) {
-		irq_domain_free_fwnode(fn);
-		kfree(domain_info);
-	}
-	return d;
-}
-
-int hpet_assign_irq(struct irq_domain *domain, struct hpet_channel *hc,
-		    int dev_num)
-{
-	struct irq_alloc_info info;
-
-	init_irq_alloc_info(&info, NULL);
-	info.type = X86_IRQ_ALLOC_TYPE_HPET;
-	info.data = hc;
-	info.devid = hpet_dev_id(domain);
-	info.hwirq = dev_num;
-
-	return irq_domain_alloc_irqs(domain, 1, NUMA_NO_NODE, &info);
-}
-#endif
diff --git a/arch/x86/kernel/hpet.c b/arch/x86/kernel/hpet.c
index 7a50f0b62a70..3b8b12769f3b 100644
--- a/arch/x86/kernel/hpet.c
+++ b/arch/x86/kernel/hpet.c
@@ -7,6 +7,7 @@
 #include <linux/cpu.h>
 #include <linux/irq.h>
 
+#include <asm/irq_remapping.h>
 #include <asm/hpet.h>
 #include <asm/time.h>
 
@@ -50,7 +51,7 @@ unsigned long				hpet_address;
 u8					hpet_blockid; /* OS timer block num */
 bool					hpet_msi_disable;
 
-#ifdef CONFIG_PCI_MSI
+#ifdef CONFIG_GENERIC_MSI_IRQ
 static DEFINE_PER_CPU(struct hpet_channel *, cpu_hpet_channel);
 static struct irq_domain		*hpet_domain;
 #endif
@@ -467,9 +468,8 @@ static void __init hpet_legacy_clockevent_register(struct hpet_channel *hc)
 /*
  * HPET MSI Support
  */
-#ifdef CONFIG_PCI_MSI
-
-void hpet_msi_unmask(struct irq_data *data)
+#ifdef CONFIG_GENERIC_MSI_IRQ
+static void hpet_msi_unmask(struct irq_data *data)
 {
 	struct hpet_channel *hc = irq_data_get_irq_handler_data(data);
 	unsigned int cfg;
@@ -479,7 +479,7 @@ void hpet_msi_unmask(struct irq_data *data)
 	hpet_writel(cfg, HPET_Tn_CFG(hc->num));
 }
 
-void hpet_msi_mask(struct irq_data *data)
+static void hpet_msi_mask(struct irq_data *data)
 {
 	struct hpet_channel *hc = irq_data_get_irq_handler_data(data);
 	unsigned int cfg;
@@ -489,12 +489,118 @@ void hpet_msi_mask(struct irq_data *data)
 	hpet_writel(cfg, HPET_Tn_CFG(hc->num));
 }
 
-void hpet_msi_write(struct hpet_channel *hc, struct msi_msg *msg)
+static void hpet_msi_write(struct hpet_channel *hc, struct msi_msg *msg)
 {
 	hpet_writel(msg->data, HPET_Tn_ROUTE(hc->num));
 	hpet_writel(msg->address_lo, HPET_Tn_ROUTE(hc->num) + 4);
 }
 
+static void hpet_msi_write_msg(struct irq_data *data, struct msi_msg *msg)
+{
+	hpet_msi_write(irq_data_get_irq_handler_data(data), msg);
+}
+
+static struct irq_chip hpet_msi_controller __ro_after_init = {
+	.name = "HPET-MSI",
+	.irq_unmask = hpet_msi_unmask,
+	.irq_mask = hpet_msi_mask,
+	.irq_ack = irq_chip_ack_parent,
+	.irq_set_affinity = msi_domain_set_affinity,
+	.irq_retrigger = irq_chip_retrigger_hierarchy,
+	.irq_write_msi_msg = hpet_msi_write_msg,
+	.flags = IRQCHIP_SKIP_SET_WAKE,
+};
+
+static int hpet_msi_init(struct irq_domain *domain,
+			 struct msi_domain_info *info, unsigned int virq,
+			 irq_hw_number_t hwirq, msi_alloc_info_t *arg)
+{
+	irq_set_status_flags(virq, IRQ_MOVE_PCNTXT);
+	irq_domain_set_info(domain, virq, arg->hwirq, info->chip, NULL,
+			    handle_edge_irq, arg->data, "edge");
+
+	return 0;
+}
+
+static void hpet_msi_free(struct irq_domain *domain,
+			  struct msi_domain_info *info, unsigned int virq)
+{
+	irq_clear_status_flags(virq, IRQ_MOVE_PCNTXT);
+}
+
+static struct msi_domain_ops hpet_msi_domain_ops = {
+	.msi_init	= hpet_msi_init,
+	.msi_free	= hpet_msi_free,
+};
+
+static struct msi_domain_info hpet_msi_domain_info = {
+	.ops		= &hpet_msi_domain_ops,
+	.chip		= &hpet_msi_controller,
+	.flags		= MSI_FLAG_USE_DEF_DOM_OPS,
+};
+
+static struct irq_domain *hpet_create_irq_domain(int hpet_id)
+{
+	struct msi_domain_info *domain_info;
+	struct irq_domain *parent, *d;
+	struct irq_alloc_info info;
+	struct fwnode_handle *fn;
+
+	if (x86_vector_domain == NULL)
+		return NULL;
+
+	domain_info = kzalloc(sizeof(*domain_info), GFP_KERNEL);
+	if (!domain_info)
+		return NULL;
+
+	*domain_info = hpet_msi_domain_info;
+	domain_info->data = (void *)(long)hpet_id;
+
+	init_irq_alloc_info(&info, NULL);
+	info.type = X86_IRQ_ALLOC_TYPE_HPET_GET_PARENT;
+	info.devid = hpet_id;
+	parent = irq_remapping_get_irq_domain(&info);
+	if (parent == NULL)
+		parent = x86_vector_domain;
+	else
+		hpet_msi_controller.name = "IR-HPET-MSI";
+
+	fn = irq_domain_alloc_named_id_fwnode(hpet_msi_controller.name,
+					      hpet_id);
+	if (!fn) {
+		kfree(domain_info);
+		return NULL;
+	}
+
+	d = msi_create_irq_domain(fn, domain_info, parent);
+	if (!d) {
+		irq_domain_free_fwnode(fn);
+		kfree(domain_info);
+	}
+	return d;
+}
+
+static inline int hpet_dev_id(struct irq_domain *domain)
+{
+	struct msi_domain_info *info = msi_get_domain_info(domain);
+
+	return (int)(long)info->data;
+}
+
+static int hpet_assign_irq(struct irq_domain *domain, struct hpet_channel *hc,
+			   int dev_num)
+{
+	struct irq_alloc_info info;
+
+	init_irq_alloc_info(&info, NULL);
+	info.type = X86_IRQ_ALLOC_TYPE_HPET;
+	info.data = hc;
+	info.devid = hpet_dev_id(domain);
+	info.hwirq = dev_num;
+
+	return irq_domain_alloc_irqs(domain, 1, NUMA_NO_NODE, &info);
+}
+
 static int hpet_clkevt_msi_resume(struct clock_event_device *evt)
 {
 	struct hpet_channel *hc = clockevent_to_channel(evt);
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 11/35] genirq/msi: Allow shadow declarations of msi_msg::$member

[David Woodhouse]

From: Thomas Gleixner <tglx@linutronix.de>

Architectures like x86 have their MSI messages in various bits of the data,
address_lo and address_hi field. Composing or decomposing these messages
with bitmasks and shifts is possible, but unreadable gunk.

Allow architectures to provide an architecture specific representation for
each member of msi_msg. Provide empty defaults for each and stick them into
an union.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
---
 include/asm-generic/msi.h |  4 ++++
 include/linux/msi.h       | 46 +++++++++++++++++++++++++++++++++++----
 2 files changed, 46 insertions(+), 4 deletions(-)

diff --git a/include/asm-generic/msi.h b/include/asm-generic/msi.h
index e6795f088bdd..25344de0e8f9 100644
--- a/include/asm-generic/msi.h
+++ b/include/asm-generic/msi.h
@@ -4,6 +4,8 @@
 
 #include <linux/types.h>
 
+#ifdef CONFIG_GENERIC_MSI_IRQ_DOMAIN
+
 #ifndef NUM_MSI_ALLOC_SCRATCHPAD_REGS
 # define NUM_MSI_ALLOC_SCRATCHPAD_REGS	2
 #endif
@@ -30,4 +32,6 @@ typedef struct msi_alloc_info {
 
 #define GENERIC_MSI_DOMAIN_OPS		1
 
+#endif /* CONFIG_GENERIC_MSI_IRQ_DOMAIN */
+
 #endif
diff --git a/include/linux/msi.h b/include/linux/msi.h
index 6b584cc4757c..360a0a7e7341 100644
--- a/include/linux/msi.h
+++ b/include/linux/msi.h
@@ -4,11 +4,50 @@
 
 #include <linux/kobject.h>
 #include <linux/list.h>
+#include <asm/msi.h>
+
+/* Dummy shadow structures if an architecture does not define them */
+#ifndef arch_msi_msg_addr_lo
+typedef struct arch_msi_msg_addr_lo {
+	u32	address_lo;
+} __attribute__ ((packed)) arch_msi_msg_addr_lo_t;
+#endif
+
+#ifndef arch_msi_msg_addr_hi
+typedef struct arch_msi_msg_addr_hi {
+	u32	address_hi;
+} __attribute__ ((packed)) arch_msi_msg_addr_hi_t;
+#endif
+
+#ifndef arch_msi_msg_data
+typedef struct arch_msi_msg_data {
+	u32	data;
+} __attribute__ ((packed)) arch_msi_msg_data_t;
+#endif
 
+/**
+ * msi_msg - Representation of a MSI message
+ * @address_lo:		Low 32 bits of msi message address
+ * @arch_addrlo:	Architecture specific shadow of @address_lo
+ * @address_hi:		High 32 bits of msi message address
+ *			(only used when device supports it)
+ * @arch_addrhi:	Architecture specific shadow of @address_hi
+ * @data:		MSI message data (usually 16 bits)
+ * @arch_data:		Architecture specific shadow of @data
+ */
 struct msi_msg {
-	u32	address_lo;	/* low 32 bits of msi message address */
-	u32	address_hi;	/* high 32 bits of msi message address */
-	u32	data;		/* 16 bits of msi message data */
+	union {
+		u32			address_lo;
+		arch_msi_msg_addr_lo_t	arch_addr_lo;
+	};
+	union {
+		u32			address_hi;
+		arch_msi_msg_addr_hi_t	arch_addr_hi;
+	};
+	union {
+		u32			data;
+		arch_msi_msg_data_t	arch_data;
+	};
 };
 
 extern int pci_msi_ignore_mask;
@@ -243,7 +282,6 @@ struct msi_controller {
 #ifdef CONFIG_GENERIC_MSI_IRQ_DOMAIN
 
 #include <linux/irqhandler.h>
-#include <asm/msi.h>
 
 struct irq_domain;
 struct irq_domain_ops;
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 12/35] x86/msi: Provide msi message shadow structs

[David Woodhouse]

From: Thomas Gleixner <tglx@linutronix.de>

Create shadow structs with named bitfields for msi_msg data, address_lo and
address_hi and use them in the MSI message composer.

Provide a function to retrieve the destination ID. This could be inline,
but that'd create a circular header dependency.

[dwmw2: fix bitfields not all to be a union]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
---
 arch/x86/include/asm/msi.h  | 49 +++++++++++++++++++++++++++++++++++++
 arch/x86/kernel/apic/apic.c | 35 ++++++++++++++------------
 2 files changed, 68 insertions(+), 16 deletions(-)

diff --git a/arch/x86/include/asm/msi.h b/arch/x86/include/asm/msi.h
index cd30013d15d3..322fd905da9c 100644
--- a/arch/x86/include/asm/msi.h
+++ b/arch/x86/include/asm/msi.h
@@ -9,4 +9,53 @@ typedef struct irq_alloc_info msi_alloc_info_t;
 int pci_msi_prepare(struct irq_domain *domain, struct device *dev, int nvec,
 		    msi_alloc_info_t *arg);
 
+/* Structs and defines for the X86 specific MSI message format */
+
+typedef struct x86_msi_data {
+	u32	vector			:  8,
+		delivery_mode		:  3,
+		dest_mode_logical	:  1,
+		reserved		:  2,
+		active_low		:  1,
+		is_level		:  1;
+
+	u32	dmar_subhandle;
+} __attribute__ ((packed)) arch_msi_msg_data_t;
+#define arch_msi_msg_data	x86_msi_data
+
+typedef struct x86_msi_addr_lo {
+	union {
+		struct {
+			u32	reserved_0		:  2,
+				dest_mode_logical	:  1,
+				redirect_hint		:  1,
+				reserved_1		:  8,
+				destid_0_7		:  8,
+				base_address		: 12;
+		};
+		struct {
+			u32	dmar_reserved_0		:  2,
+				dmar_index_15		:  1,
+				dmar_subhandle_valid	:  1,
+				dmar_format		:  1,
+				dmar_index_0_14		: 15,
+				dmar_base_address	: 12;
+		};
+	};
+} __attribute__ ((packed)) arch_msi_msg_addr_lo_t;
+#define arch_msi_msg_addr_lo	x86_msi_addr_lo
+
+#define X86_MSI_BASE_ADDRESS_LOW	(0xfee00000 >> 20)
+
+typedef struct x86_msi_addr_hi {
+	u32	reserved		:  8,
+		destid_8_31		: 24;
+} __attribute__ ((packed)) arch_msi_msg_addr_hi_t;
+#define arch_msi_msg_addr_hi	x86_msi_addr_hi
+
+#define X86_MSI_BASE_ADDRESS_HIGH	(0)
+
+struct msi_msg;
+u32 x86_msi_msg_get_destid(struct msi_msg *msg, bool extid);
+
 #endif /* _ASM_X86_MSI_H */
diff --git a/arch/x86/kernel/apic/apic.c b/arch/x86/kernel/apic/apic.c
index 4c15bf29ea2c..f7196ee0f005 100644
--- a/arch/x86/kernel/apic/apic.c
+++ b/arch/x86/kernel/apic/apic.c
@@ -50,7 +50,6 @@
 #include <asm/io_apic.h>
 #include <asm/desc.h>
 #include <asm/hpet.h>
-#include <asm/msidef.h>
 #include <asm/mtrr.h>
 #include <asm/time.h>
 #include <asm/smp.h>
@@ -2484,22 +2483,16 @@ int hard_smp_processor_id(void)
 void __irq_msi_compose_msg(struct irq_cfg *cfg, struct msi_msg *msg,
 			   bool dmar)
 {
-	msg->address_hi = MSI_ADDR_BASE_HI;
+	memset(msg, 0, sizeof(*msg));
 
-	msg->address_lo =
-		MSI_ADDR_BASE_LO |
-		(apic->dest_mode_logical ?
-			MSI_ADDR_DEST_MODE_LOGICAL :
-			MSI_ADDR_DEST_MODE_PHYSICAL) |
-		MSI_ADDR_REDIRECTION_CPU |
-		MSI_ADDR_DEST_ID(cfg->dest_apicid);
+	msg->arch_addr_lo.base_address = X86_MSI_BASE_ADDRESS_LOW;
+	msg->arch_addr_lo.dest_mode_logical = apic->dest_mode_logical;
+	msg->arch_addr_lo.destid_0_7 = cfg->dest_apicid & 0xFF;
 
-	msg->data =
-		MSI_DATA_TRIGGER_EDGE |
-		MSI_DATA_LEVEL_ASSERT |
-		MSI_DATA_DELIVERY_FIXED |
-		MSI_DATA_VECTOR(cfg->vector);
+	msg->arch_data.delivery_mode = APIC_DELIVERY_MODE_FIXED;
+	msg->arch_data.vector = cfg->vector;
 
+	msg->address_hi = X86_MSI_BASE_ADDRESS_HIGH;
 	/*
 	 * Only the IOMMU itself can use the trick of putting destination
 	 * APIC ID into the high bits of the address. Anything else would
@@ -2507,11 +2500,21 @@ void __irq_msi_compose_msg(struct irq_cfg *cfg, struct msi_msg *msg,
 	 * address higher APIC IDs.
 	 */
 	if (dmar)
-		msg->address_hi |= MSI_ADDR_EXT_DEST_ID(cfg->dest_apicid);
+		msg->arch_addr_hi.destid_8_31 = cfg->dest_apicid >> 8;
 	else
-		WARN_ON_ONCE(MSI_ADDR_EXT_DEST_ID(cfg->dest_apicid));
+		WARN_ON_ONCE(cfg->dest_apicid > 0xFF);
 }
 
+u32 x86_msi_msg_get_destid(struct msi_msg *msg, bool extid)
+{
+	u32 dest = msg->arch_addr_lo.destid_0_7;
+
+	if (extid)
+		dest |= msg->arch_addr_hi.destid_8_31 << 8;
+	return dest;
+}
+EXPORT_SYMBOL_GPL(x86_msi_msg_get_destid);
+
 /*
  * Override the generic EOI implementation with an optimized version.
  * Only called during early boot when only one CPU is active and with
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

Re: [PATCH v3 12/35] x86/msi: Provide msi message shadow structs

[Reto Buerki]

While working on some out-of-tree patches, we noticed that assignment to
dmar_subhandle of struct x86_msi_data lead to a QEMU warning about
reserved bits in MSI data being set:

qemu-system-x86_64: vtd_interrupt_remap_msi: invalid IR MSI (sid=256, address=0xfee003d8, data=0x10000)

This message originates from hw/i386/intel_iommu.c in QEMU:

#define VTD_IR_MSI_DATA_RESERVED (0xffff0000)
if (origin->data & VTD_IR_MSI_DATA_RESERVED) { ... }

Looking at struct x86_msi_data, it appears that it is actually 48-bits in size
since the bitfield containing the vector, delivery_mode etc is 2 bytes wide
followed by dmar_subhandle which is 32 bits. Thus assignment to dmar_subhandle
leads to bits > 16 being set.

If I am not mistaken, the MSI data field should be 32-bits wide for all
platforms (struct msi_msg, include/linux/msi.h). Is this analysis
correct or did I miss something wrt. handling of dmar_subhandle?

The attached patch fixes the issue for us.

Regards,
- reto
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH] x86/msi: Fix msi message data shadow struct

[Reto Buerki]

The x86 MSI message data is 32 bits in total and is either in
compatibility or remappable format, see Intel Virtualization Technology
for Directed I/O, section 5.1.2.

Fixes: 6285aa50736 ("x86/msi: Provide msi message shadow structs")
Signed-off-by: Reto Buerki <reet@codelabs.ch>
Signed-off-by: Adrian-Ken Rueegsegger <ken@codelabs.ch>
---
 arch/x86/include/asm/msi.h | 19 +++++++++++--------
 1 file changed, 11 insertions(+), 8 deletions(-)

diff --git a/arch/x86/include/asm/msi.h b/arch/x86/include/asm/msi.h
index b85147d75626..d71c7e8b738d 100644
--- a/arch/x86/include/asm/msi.h
+++ b/arch/x86/include/asm/msi.h
@@ -12,14 +12,17 @@ int pci_msi_prepare(struct irq_domain *domain, struct device *dev, int nvec,
 /* Structs and defines for the X86 specific MSI message format */
 
 typedef struct x86_msi_data {
-	u32	vector			:  8,
-		delivery_mode		:  3,
-		dest_mode_logical	:  1,
-		reserved		:  2,
-		active_low		:  1,
-		is_level		:  1;
-
-	u32	dmar_subhandle;
+	union {
+		struct {
+			u32	vector			:  8,
+				delivery_mode		:  3,
+				dest_mode_logical	:  1,
+				reserved		:  2,
+				active_low		:  1,
+				is_level		:  1;
+		};
+		u32	dmar_subhandle;
+	};
 } __attribute__ ((packed)) arch_msi_msg_data_t;
 #define arch_msi_msg_data	x86_msi_data
 
-- 
2.30.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

Re: [PATCH] x86/msi: Fix msi message data shadow struct

[Thomas Gleixner]

Reto,

On Wed, Apr 06 2022 at 10:36, Reto Buerki wrote:

> The x86 MSI message data is 32 bits in total and is either in
> compatibility or remappable format, see Intel Virtualization Technology
> for Directed I/O, section 5.1.2.
>
> Fixes: 6285aa50736 ("x86/msi: Provide msi message shadow structs")
> Signed-off-by: Reto Buerki <reet@codelabs.ch>
> Signed-off-by: Adrian-Ken Rueegsegger <ken@codelabs.ch>

This signed-off by chain is incorrect. It would be correct if Adrian-Ken
would have sent the patch.

If you both worked on that then please use the Co-developed-by tag
according to Documentation/process/

Thanks,

        tglx
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH] x86/msi: Fix msi message data shadow struct

[Reto Buerki]

The x86 MSI message data is 32 bits in total and is either in
compatibility or remappable format, see Intel Virtualization Technology
for Directed I/O, section 5.1.2.

Fixes: 6285aa50736 ("x86/msi: Provide msi message shadow structs")
Co-developed-by: Adrian-Ken Rueegsegger <ken@codelabs.ch>
Signed-off-by: Adrian-Ken Rueegsegger <ken@codelabs.ch>
Signed-off-by: Reto Buerki <reet@codelabs.ch>
---
 arch/x86/include/asm/msi.h | 19 +++++++++++--------
 1 file changed, 11 insertions(+), 8 deletions(-)

diff --git a/arch/x86/include/asm/msi.h b/arch/x86/include/asm/msi.h
index b85147d75626..d71c7e8b738d 100644
--- a/arch/x86/include/asm/msi.h
+++ b/arch/x86/include/asm/msi.h
@@ -12,14 +12,17 @@ int pci_msi_prepare(struct irq_domain *domain, struct device *dev, int nvec,
 /* Structs and defines for the X86 specific MSI message format */
 
 typedef struct x86_msi_data {
-	u32	vector			:  8,
-		delivery_mode		:  3,
-		dest_mode_logical	:  1,
-		reserved		:  2,
-		active_low		:  1,
-		is_level		:  1;
-
-	u32	dmar_subhandle;
+	union {
+		struct {
+			u32	vector			:  8,
+				delivery_mode		:  3,
+				dest_mode_logical	:  1,
+				reserved		:  2,
+				active_low		:  1,
+				is_level		:  1;
+		};
+		u32	dmar_subhandle;
+	};
 } __attribute__ ((packed)) arch_msi_msg_data_t;
 #define arch_msi_msg_data	x86_msi_data
 
-- 
2.30.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

Re: [PATCH v3 12/35] x86/msi: Provide msi message shadow structs

[Thomas Gleixner]

On Wed, Apr 06 2022 at 10:36, Reto Buerki wrote:
> While working on some out-of-tree patches, we noticed that assignment to
> dmar_subhandle of struct x86_msi_data lead to a QEMU warning about
> reserved bits in MSI data being set:
>
> qemu-system-x86_64: vtd_interrupt_remap_msi: invalid IR MSI (sid=256, address=0xfee003d8, data=0x10000)
>
> This message originates from hw/i386/intel_iommu.c in QEMU:
>
> #define VTD_IR_MSI_DATA_RESERVED (0xffff0000)
> if (origin->data & VTD_IR_MSI_DATA_RESERVED) { ... }
>
> Looking at struct x86_msi_data, it appears that it is actually 48-bits in size
> since the bitfield containing the vector, delivery_mode etc is 2 bytes wide
> followed by dmar_subhandle which is 32 bits. Thus assignment to dmar_subhandle
> leads to bits > 16 being set.
>
> If I am not mistaken, the MSI data field should be 32-bits wide for all
> platforms (struct msi_msg, include/linux/msi.h). Is this analysis
> correct or did I miss something wrt. handling of dmar_subhandle?

It's correct and I'm completely surprised that this went unnoticed
for more than a year. Where is that brown paperbag...

Thanks,

        tglx

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 13/35] iommu/intel: Use msi_msg shadow structs

[David Woodhouse]

From: Thomas Gleixner <tglx@linutronix.de>

Use the bitfields in the x86 shadow struct to compose the MSI message.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
---
 drivers/iommu/intel/irq_remapping.c | 24 ++++++++++++++++--------
 1 file changed, 16 insertions(+), 8 deletions(-)

diff --git a/drivers/iommu/intel/irq_remapping.c b/drivers/iommu/intel/irq_remapping.c
index 5628d43b795e..30269b738fa5 100644
--- a/drivers/iommu/intel/irq_remapping.c
+++ b/drivers/iommu/intel/irq_remapping.c
@@ -20,7 +20,6 @@
 #include <asm/cpu.h>
 #include <asm/irq_remapping.h>
 #include <asm/pci-direct.h>
-#include <asm/msidef.h>
 
 #include "../irq_remapping.h"
 
@@ -1260,6 +1259,21 @@ static struct irq_chip intel_ir_chip = {
 	.irq_set_vcpu_affinity	= intel_ir_set_vcpu_affinity,
 };
 
+static void fill_msi_msg(struct msi_msg *msg, u32 index, u32 subhandle)
+{
+	memset(msg, 0, sizeof(*msg));
+
+	msg->arch_addr_lo.dmar_base_address = X86_MSI_BASE_ADDRESS_LOW;
+	msg->arch_addr_lo.dmar_subhandle_valid = true;
+	msg->arch_addr_lo.dmar_format = true;
+	msg->arch_addr_lo.dmar_index_0_14 = index & 0x7FFF;
+	msg->arch_addr_lo.dmar_index_15 = !!(index & 0x8000);
+
+	msg->address_hi = X86_MSI_BASE_ADDRESS_HIGH;
+
+	msg->arch_data.dmar_subhandle = subhandle;
+}
+
 static void intel_irq_remapping_prepare_irte(struct intel_ir_data *data,
 					     struct irq_cfg *irq_cfg,
 					     struct irq_alloc_info *info,
@@ -1267,7 +1281,6 @@ static void intel_irq_remapping_prepare_irte(struct intel_ir_data *data,
 {
 	struct IR_IO_APIC_route_entry *entry;
 	struct irte *irte = &data->irte_entry;
-	struct msi_msg *msg = &data->msi_entry;
 
 	prepare_irte(irte, irq_cfg->vector, irq_cfg->dest_apicid);
 	switch (info->type) {
@@ -1308,12 +1321,7 @@ static void intel_irq_remapping_prepare_irte(struct intel_ir_data *data,
 		else
 			set_msi_sid(irte, msi_desc_to_pci_dev(info->desc));
 
-		msg->address_hi = MSI_ADDR_BASE_HI;
-		msg->data = sub_handle;
-		msg->address_lo = MSI_ADDR_BASE_LO | MSI_ADDR_IR_EXT_INT |
-				  MSI_ADDR_IR_SHV |
-				  MSI_ADDR_IR_INDEX1(index) |
-				  MSI_ADDR_IR_INDEX2(index);
+		fill_msi_msg(&data->msi_entry, index, sub_handle);
 		break;
 
 	default:
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 14/35] iommu/amd: Use msi_msg shadow structs

[David Woodhouse]

From: Thomas Gleixner <tglx@linutronix.de>

Get rid of the macro mess and use the shadow structs for the x86 specific
MSI message format. Convert the intcapxt setup to use named bitfields as
well while touching it anyway.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
---
 drivers/iommu/amd/init.c  | 46 ++++++++++++++++++++++-----------------
 drivers/iommu/amd/iommu.c | 14 +++++++-----
 2 files changed, 35 insertions(+), 25 deletions(-)

diff --git a/drivers/iommu/amd/init.c b/drivers/iommu/amd/init.c
index 82e4af8f09bb..263670d36fed 100644
--- a/drivers/iommu/amd/init.c
+++ b/drivers/iommu/amd/init.c
@@ -23,7 +23,6 @@
 #include <asm/pci-direct.h>
 #include <asm/iommu.h>
 #include <asm/apic.h>
-#include <asm/msidef.h>
 #include <asm/gart.h>
 #include <asm/x86_init.h>
 #include <asm/iommu_table.h>
@@ -1966,10 +1965,16 @@ static int iommu_setup_msi(struct amd_iommu *iommu)
 	return 0;
 }
 
-#define XT_INT_DEST_MODE(x)	(((x) & 0x1ULL) << 2)
-#define XT_INT_DEST_LO(x)	(((x) & 0xFFFFFFULL) << 8)
-#define XT_INT_VEC(x)		(((x) & 0xFFULL) << 32)
-#define XT_INT_DEST_HI(x)	((((x) >> 24) & 0xFFULL) << 56)
+union intcapxt {
+	u64	capxt;
+	u64	reserved_0		:  2,
+		dest_mode_logical	:  1,
+		reserved_1		:  5,
+		destid_0_23		: 24,
+		vector			:  8,
+		reserved_2		: 16,
+		destid_24_31		:  8;
+} __attribute__ ((packed));
 
 /*
  * Setup the IntCapXT registers with interrupt routing information
@@ -1978,28 +1983,29 @@ static int iommu_setup_msi(struct amd_iommu *iommu)
  */
 static void iommu_update_intcapxt(struct amd_iommu *iommu)
 {
-	u64 val;
-	u32 addr_lo = readl(iommu->mmio_base + MMIO_MSI_ADDR_LO_OFFSET);
-	u32 addr_hi = readl(iommu->mmio_base + MMIO_MSI_ADDR_HI_OFFSET);
-	u32 data    = readl(iommu->mmio_base + MMIO_MSI_DATA_OFFSET);
-	bool dm     = (addr_lo >> MSI_ADDR_DEST_MODE_SHIFT) & 0x1;
-	u32 dest    = ((addr_lo >> MSI_ADDR_DEST_ID_SHIFT) & 0xFF);
+	struct msi_msg msg;
+	union intcapxt xt;
+	u32 destid;
 
-	if (x2apic_enabled())
-		dest |= MSI_ADDR_EXT_DEST_ID(addr_hi);
+	msg.address_lo = readl(iommu->mmio_base + MMIO_MSI_ADDR_LO_OFFSET);
+	msg.address_hi = readl(iommu->mmio_base + MMIO_MSI_ADDR_HI_OFFSET);
+	msg.data = readl(iommu->mmio_base + MMIO_MSI_DATA_OFFSET);
 
-	val = XT_INT_VEC(data & 0xFF) |
-	      XT_INT_DEST_MODE(dm) |
-	      XT_INT_DEST_LO(dest) |
-	      XT_INT_DEST_HI(dest);
+	destid = x86_msi_msg_get_destid(&msg, x2apic_enabled());
+
+	xt.capxt = 0ULL;
+	xt.dest_mode_logical = msg.arch_data.dest_mode_logical;
+	xt.vector = msg.arch_data.vector;
+	xt.destid_0_23 = destid & GENMASK(23, 0);
+	xt.destid_24_31 = destid >> 24;
 
 	/**
 	 * Current IOMMU implemtation uses the same IRQ for all
 	 * 3 IOMMU interrupts.
 	 */
-	writeq(val, iommu->mmio_base + MMIO_INTCAPXT_EVT_OFFSET);
-	writeq(val, iommu->mmio_base + MMIO_INTCAPXT_PPR_OFFSET);
-	writeq(val, iommu->mmio_base + MMIO_INTCAPXT_GALOG_OFFSET);
+	writeq(xt.capxt, iommu->mmio_base + MMIO_INTCAPXT_EVT_OFFSET);
+	writeq(xt.capxt, iommu->mmio_base + MMIO_INTCAPXT_PPR_OFFSET);
+	writeq(xt.capxt, iommu->mmio_base + MMIO_INTCAPXT_GALOG_OFFSET);
 }
 
 static void _irq_notifier_notify(struct irq_affinity_notify *notify,
diff --git a/drivers/iommu/amd/iommu.c b/drivers/iommu/amd/iommu.c
index d7f0c8908602..473de0920b64 100644
--- a/drivers/iommu/amd/iommu.c
+++ b/drivers/iommu/amd/iommu.c
@@ -35,7 +35,6 @@
 #include <asm/io_apic.h>
 #include <asm/apic.h>
 #include <asm/hw_irq.h>
-#include <asm/msidef.h>
 #include <asm/proto.h>
 #include <asm/iommu.h>
 #include <asm/gart.h>
@@ -3656,13 +3655,20 @@ struct irq_remap_ops amd_iommu_irq_ops = {
 	.get_irq_domain		= get_irq_domain,
 };
 
+static void fill_msi_msg(struct msi_msg *msg, u32 index)
+{
+	msg->data = index;
+	msg->address_lo = 0;
+	msg->arch_addr_lo.base_address = X86_MSI_BASE_ADDRESS_LOW;
+	msg->address_hi = X86_MSI_BASE_ADDRESS_HIGH;
+}
+
 static void irq_remapping_prepare_irte(struct amd_ir_data *data,
 				       struct irq_cfg *irq_cfg,
 				       struct irq_alloc_info *info,
 				       int devid, int index, int sub_handle)
 {
 	struct irq_2_irte *irte_info = &data->irq_2_irte;
-	struct msi_msg *msg = &data->msi_entry;
 	struct IO_APIC_route_entry *entry;
 	struct amd_iommu *iommu = amd_iommu_rlookup_table[devid];
 
@@ -3693,9 +3699,7 @@ static void irq_remapping_prepare_irte(struct amd_ir_data *data,
 	case X86_IRQ_ALLOC_TYPE_HPET:
 	case X86_IRQ_ALLOC_TYPE_PCI_MSI:
 	case X86_IRQ_ALLOC_TYPE_PCI_MSIX:
-		msg->address_hi = MSI_ADDR_BASE_HI;
-		msg->address_lo = MSI_ADDR_BASE_LO;
-		msg->data = irte_info->index;
+		fill_msi_msg(&data->msi_entry, irte_info->index);
 		break;
 
 	default:
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 15/35] PCI: vmd: Use msi_msg shadow structs

[David Woodhouse]

From: Thomas Gleixner <tglx@linutronix.de>

Use the x86 shadow structs in msi_msg instead of the macros.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
---
 drivers/pci/controller/vmd.c | 9 ++++-----
 1 file changed, 4 insertions(+), 5 deletions(-)

diff --git a/drivers/pci/controller/vmd.c b/drivers/pci/controller/vmd.c
index aa1b12bac9a1..72de3c6f644e 100644
--- a/drivers/pci/controller/vmd.c
+++ b/drivers/pci/controller/vmd.c
@@ -18,7 +18,6 @@
 #include <asm/irqdomain.h>
 #include <asm/device.h>
 #include <asm/msi.h>
-#include <asm/msidef.h>
 
 #define VMD_CFGBAR	0
 #define VMD_MEMBAR1	2
@@ -131,10 +130,10 @@ static void vmd_compose_msi_msg(struct irq_data *data, struct msi_msg *msg)
 	struct vmd_irq_list *irq = vmdirq->irq;
 	struct vmd_dev *vmd = irq_data_get_irq_handler_data(data);
 
-	msg->address_hi = MSI_ADDR_BASE_HI;
-	msg->address_lo = MSI_ADDR_BASE_LO |
-			  MSI_ADDR_DEST_ID(index_from_irqs(vmd, irq));
-	msg->data = 0;
+	memset(&msg, 0, sizeof(*msg);
+	msg->address_hi = X86_MSI_BASE_ADDRESS_HIGH;
+	msg->arch_addr_lo.base_address = X86_MSI_BASE_ADDRESS_LOW;
+	msg->arch_addr_lo.destid_0_7 = index_from_irqs(vmd, irq);
 }
 
 /*
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

Re: [PATCH v3 15/35] PCI: vmd: Use msi_msg shadow structs

[Kees Cook]

On Sat, Oct 24, 2020 at 10:35:15PM +0100, David Woodhouse wrote:
> From: Thomas Gleixner <tglx@linutronix.de>
> 
> Use the x86 shadow structs in msi_msg instead of the macros.
> 
> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
> Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
> ---
>  drivers/pci/controller/vmd.c | 9 ++++-----
>  1 file changed, 4 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/pci/controller/vmd.c b/drivers/pci/controller/vmd.c
> index aa1b12bac9a1..72de3c6f644e 100644
> --- a/drivers/pci/controller/vmd.c
> +++ b/drivers/pci/controller/vmd.c
> @@ -18,7 +18,6 @@
>  #include <asm/irqdomain.h>
>  #include <asm/device.h>
>  #include <asm/msi.h>
> -#include <asm/msidef.h>
>  
>  #define VMD_CFGBAR	0
>  #define VMD_MEMBAR1	2
> @@ -131,10 +130,10 @@ static void vmd_compose_msi_msg(struct irq_data *data, struct msi_msg *msg)
>  	struct vmd_irq_list *irq = vmdirq->irq;
>  	struct vmd_dev *vmd = irq_data_get_irq_handler_data(data);
>  
> -	msg->address_hi = MSI_ADDR_BASE_HI;
> -	msg->address_lo = MSI_ADDR_BASE_LO |
> -			  MSI_ADDR_DEST_ID(index_from_irqs(vmd, irq));
> -	msg->data = 0;
> +	memset(&msg, 0, sizeof(*msg);

This should be:

+	memset(msg, 0, sizeof(*msg);

https://groups.google.com/g/clang-built-linux/c/N-DfCPz3alg

> +	msg->address_hi = X86_MSI_BASE_ADDRESS_HIGH;
> +	msg->arch_addr_lo.base_address = X86_MSI_BASE_ADDRESS_LOW;
> +	msg->arch_addr_lo.destid_0_7 = index_from_irqs(vmd, irq);
>  }
>  
>  /*
> -- 
> 2.26.2
> 

-- 
Kees Cook
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

Re: [PATCH v3 15/35] PCI: vmd: Use msi_msg shadow structs

[Thomas Gleixner]

On Wed, Oct 28 2020 at 13:49, Kees Cook wrote:
> On Sat, Oct 24, 2020 at 10:35:15PM +0100, David Woodhouse wrote:
>> +	memset(&msg, 0, sizeof(*msg);
>
> This should be:
>
> +	memset(msg, 0, sizeof(*msg);

        memset(msg, 0, sizeof(*msg));

Then it compiles _and_ is correct :)
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

Re: [PATCH v3 15/35] PCI: vmd: Use msi_msg shadow structs

[Kees Cook]

On Wed, Oct 28, 2020 at 10:13:52PM +0100, Thomas Gleixner wrote:
> On Wed, Oct 28 2020 at 13:49, Kees Cook wrote:
> > On Sat, Oct 24, 2020 at 10:35:15PM +0100, David Woodhouse wrote:
> >> +	memset(&msg, 0, sizeof(*msg);
> >
> > This should be:
> >
> > +	memset(msg, 0, sizeof(*msg);
> 
>         memset(msg, 0, sizeof(*msg));
> 
> Then it compiles _and_ is correct :)

\o/ ;)

-- 
Kees Cook
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 16/35] x86/kvm: Use msi_msg shadow structs

[David Woodhouse]

From: Thomas Gleixner <tglx@linutronix.de>

Use the bitfields in the x86 shadow structs instead of decomposing the
32bit value with macros.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
---
 arch/x86/kvm/irq_comm.c | 31 +++++++++++++------------------
 1 file changed, 13 insertions(+), 18 deletions(-)

diff --git a/arch/x86/kvm/irq_comm.c b/arch/x86/kvm/irq_comm.c
index 4aa1c2e00e2a..8a4de3f12820 100644
--- a/arch/x86/kvm/irq_comm.c
+++ b/arch/x86/kvm/irq_comm.c
@@ -16,8 +16,6 @@
 
 #include <trace/events/kvm.h>
 
-#include <asm/msidef.h>
-
 #include "irq.h"
 
 #include "ioapic.h"
@@ -104,22 +102,19 @@ int kvm_irq_delivery_to_apic(struct kvm *kvm, struct kvm_lapic *src,
 void kvm_set_msi_irq(struct kvm *kvm, struct kvm_kernel_irq_routing_entry *e,
 		     struct kvm_lapic_irq *irq)
 {
-	trace_kvm_msi_set_irq(e->msi.address_lo | (kvm->arch.x2apic_format ?
-	                                     (u64)e->msi.address_hi << 32 : 0),
-	                      e->msi.data);
-
-	irq->dest_id = (e->msi.address_lo &
-			MSI_ADDR_DEST_ID_MASK) >> MSI_ADDR_DEST_ID_SHIFT;
-	if (kvm->arch.x2apic_format)
-		irq->dest_id |= MSI_ADDR_EXT_DEST_ID(e->msi.address_hi);
-	irq->vector = (e->msi.data &
-			MSI_DATA_VECTOR_MASK) >> MSI_DATA_VECTOR_SHIFT;
-	irq->dest_mode = kvm_lapic_irq_dest_mode(
-	    !!((1 << MSI_ADDR_DEST_MODE_SHIFT) & e->msi.address_lo));
-	irq->trig_mode = (1 << MSI_DATA_TRIGGER_SHIFT) & e->msi.data;
-	irq->delivery_mode = e->msi.data & 0x700;
-	irq->msi_redir_hint = ((e->msi.address_lo
-		& MSI_ADDR_REDIRECTION_LOWPRI) > 0);
+	struct msi_msg msg = { .address_lo = e->msi.address_lo,
+			       .address_hi = e->msi.address_hi,
+			       .data = e->msi.data };
+
+	trace_kvm_msi_set_irq(msg.address_lo | (kvm->arch.x2apic_format ?
+			      (u64)msg.address_hi << 32 : 0), msg.data);
+
+	irq->dest_id = x86_msi_msg_get_destid(&msg, kvm->arch.x2apic_format);
+	irq->vector = msg.arch_data.vector;
+	irq->dest_mode = kvm_lapic_irq_dest_mode(msg.arch_addr_lo.dest_mode_logical);
+	irq->trig_mode = msg.arch_data.is_level;
+	irq->delivery_mode = msg.arch_data.delivery_mode << 8;
+	irq->msi_redir_hint = msg.arch_addr_lo.redirect_hint;
 	irq->level = 1;
 	irq->shorthand = APIC_DEST_NOSHORT;
 }
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 17/35] x86/pci/xen: Use msi_msg shadow structs

[David Woodhouse]

From: Thomas Gleixner <tglx@linutronix.de>

Use the msi_msg shadow structs and compose the message with named bitfields
instead of the unreadable macro maze.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
---
 arch/x86/pci/xen.c | 26 +++++++++++---------------
 1 file changed, 11 insertions(+), 15 deletions(-)

diff --git a/arch/x86/pci/xen.c b/arch/x86/pci/xen.c
index c552cd2d0632..3d41a09c2c14 100644
--- a/arch/x86/pci/xen.c
+++ b/arch/x86/pci/xen.c
@@ -152,7 +152,6 @@ static int acpi_register_gsi_xen(struct device *dev, u32 gsi,
 
 #if defined(CONFIG_PCI_MSI)
 #include <linux/msi.h>
-#include <asm/msidef.h>
 
 struct xen_pci_frontend_ops *xen_pci_frontend;
 EXPORT_SYMBOL_GPL(xen_pci_frontend);
@@ -210,23 +209,20 @@ static int xen_setup_msi_irqs(struct pci_dev *dev, int nvec, int type)
 	return ret;
 }
 
-#define XEN_PIRQ_MSI_DATA  (MSI_DATA_TRIGGER_EDGE | \
-		MSI_DATA_LEVEL_ASSERT | (3 << 8) | MSI_DATA_VECTOR(0))
-
 static void xen_msi_compose_msg(struct pci_dev *pdev, unsigned int pirq,
 		struct msi_msg *msg)
 {
-	/* We set vector == 0 to tell the hypervisor we don't care about it,
-	 * but we want a pirq setup instead.
-	 * We use the dest_id field to pass the pirq that we want. */
-	msg->address_hi = MSI_ADDR_BASE_HI | MSI_ADDR_EXT_DEST_ID(pirq);
-	msg->address_lo =
-		MSI_ADDR_BASE_LO |
-		MSI_ADDR_DEST_MODE_PHYSICAL |
-		MSI_ADDR_REDIRECTION_CPU |
-		MSI_ADDR_DEST_ID(pirq);
-
-	msg->data = XEN_PIRQ_MSI_DATA;
+	/*
+	 * We set vector == 0 to tell the hypervisor we don't care about
+	 * it, but we want a pirq setup instead.  We use the dest_id fields
+	 * to pass the pirq that we want.
+	 */
+	memset(msg, 0, sizeof(*msg));
+	msg->address_hi = X86_MSI_BASE_ADDRESS_HIGH;
+	msg->arch_addr_hi.destid_8_31 = pirq >> 8;
+	msg->arch_addr_lo.destid_0_7 = pirq & 0xFF;
+	msg->arch_addr_lo.base_address = X86_MSI_BASE_ADDRESS_LOW;
+	msg->arch_data.delivery_mode = APIC_DELIVERY_MODE_EXTINT;
 }
 
 static int xen_hvm_setup_msi_irqs(struct pci_dev *dev, int nvec, int type)
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

RE: [PATCH v3 17/35] x86/pci/xen: Use msi_msg shadow structs

[David Laight]

From: David Woodhouse
> Sent: 24 October 2020 22:35
> 
> From: Thomas Gleixner <tglx@linutronix.de>
> 
> Use the msi_msg shadow structs and compose the message with named bitfields
> instead of the unreadable macro maze.
> 
> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
> Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
> ---
>  arch/x86/pci/xen.c | 26 +++++++++++---------------
>  1 file changed, 11 insertions(+), 15 deletions(-)
> 
> diff --git a/arch/x86/pci/xen.c b/arch/x86/pci/xen.c
> index c552cd2d0632..3d41a09c2c14 100644
> --- a/arch/x86/pci/xen.c
> +++ b/arch/x86/pci/xen.c
> @@ -152,7 +152,6 @@ static int acpi_register_gsi_xen(struct device *dev, u32 gsi,
> 
>  #if defined(CONFIG_PCI_MSI)
>  #include <linux/msi.h>
> -#include <asm/msidef.h>
> 
>  struct xen_pci_frontend_ops *xen_pci_frontend;
>  EXPORT_SYMBOL_GPL(xen_pci_frontend);
> @@ -210,23 +209,20 @@ static int xen_setup_msi_irqs(struct pci_dev *dev, int nvec, int type)
>  	return ret;
>  }
> 
> -#define XEN_PIRQ_MSI_DATA  (MSI_DATA_TRIGGER_EDGE | \
> -		MSI_DATA_LEVEL_ASSERT | (3 << 8) | MSI_DATA_VECTOR(0))
> -
>  static void xen_msi_compose_msg(struct pci_dev *pdev, unsigned int pirq,
>  		struct msi_msg *msg)
>  {
> -	/* We set vector == 0 to tell the hypervisor we don't care about it,
> -	 * but we want a pirq setup instead.
> -	 * We use the dest_id field to pass the pirq that we want. */
> -	msg->address_hi = MSI_ADDR_BASE_HI | MSI_ADDR_EXT_DEST_ID(pirq);
> -	msg->address_lo =
> -		MSI_ADDR_BASE_LO |
> -		MSI_ADDR_DEST_MODE_PHYSICAL |
> -		MSI_ADDR_REDIRECTION_CPU |
> -		MSI_ADDR_DEST_ID(pirq);
> -
> -	msg->data = XEN_PIRQ_MSI_DATA;
> +	/*
> +	 * We set vector == 0 to tell the hypervisor we don't care about
> +	 * it, but we want a pirq setup instead.  We use the dest_id fields
> +	 * to pass the pirq that we want.
> +	 */
> +	memset(msg, 0, sizeof(*msg));
> +	msg->address_hi = X86_MSI_BASE_ADDRESS_HIGH;
> +	msg->arch_addr_hi.destid_8_31 = pirq >> 8;
> +	msg->arch_addr_lo.destid_0_7 = pirq & 0xFF;
> +	msg->arch_addr_lo.base_address = X86_MSI_BASE_ADDRESS_LOW;
> +	msg->arch_data.delivery_mode = APIC_DELIVERY_MODE_EXTINT;
>  }

Just looking at a random one of these patches...

Does the compiler manage to optimise that reasonably?
Or does it generate a lot of shifts and masks as each
bitfield is set?

The code generation for bitfields is often a lot worse
that that for |= setting bits in a word.

	David

-
Registered Address Lakeside, Bramley Road, Mount Farm, Milton Keynes, MK1 1PT, UK
Registration No: 1397386 (Wales)

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

Re: [PATCH v3 17/35] x86/pci/xen: Use msi_msg shadow structs

[David Woodhouse]

[-- Attachment #1.1: Type: text/plain, Size: 4547 bytes --]

On Sun, 2020-10-25 at 09:49 +0000, David Laight wrote:
> Just looking at a random one of these patches...
> 
> Does the compiler manage to optimise that reasonably?
> Or does it generate a lot of shifts and masks as each
> bitfield is set?
> 
> The code generation for bitfields is often a lot worse
> that that for |= setting bits in a word.

Indeed, it appears to be utterly appalling. That was one of my
motivations for doing it with masks and shifts in the first place.

Because in ioapic_setup_msg_from_msi(), for example, these two are
consecutive in both source and destination:

	entry->vector			= msg.arch_data.vector;
	entry->delivery_mode		= msg.arch_data.delivery_mode;

And so are those:

	entry->ir_format		= msg.arch_addr_lo.dmar_format;
	entry->ir_index_0_14		= msg.arch_addr_lo.dmar_index_0_14;

But GCC 7.5.0 here is doing them all separately...

00000000000011e0 <ioapic_setup_msg_from_msi>:
{
    11e0:       53                      push   %rbx
    11e1:       48 89 f3                mov    %rsi,%rbx
    11e4:       48 83 ec 18             sub    $0x18,%rsp
        irq_chip_compose_msi_msg(irq_data, &msg);
    11e8:       48 89 e6                mov    %rsp,%rsi
{
    11eb:       65 48 8b 04 25 28 00    mov    %gs:0x28,%rax
    11f2:       00 00 
    11f4:       48 89 44 24 10          mov    %rax,0x10(%rsp)
    11f9:       31 c0                   xor    %eax,%eax
        irq_chip_compose_msi_msg(irq_data, &msg);
    11fb:       e8 00 00 00 00          callq  1200 <ioapic_setup_msg_from_msi+0x20>
        entry->vector                   = msg.arch_data.vector;
    1200:       0f b6 44 24 08          movzbl 0x8(%rsp),%eax
        entry->delivery_mode            = msg.arch_data.delivery_mode;
    1205:       0f b6 53 01             movzbl 0x1(%rbx),%edx
    1209:       0f b6 74 24 09          movzbl 0x9(%rsp),%esi
        entry->vector                   = msg.arch_data.vector;
    120e:       88 03                   mov    %al,(%rbx)
        entry->dest_mode_logical        = msg.arch_addr_lo.dest_mode_logical;
    1210:       0f b6 04 24             movzbl (%rsp),%eax
        entry->delivery_mode            = msg.arch_data.delivery_mode;
    1214:       83 e2 f0                and    $0xfffffff0,%edx
    1217:       83 e6 07                and    $0x7,%esi
        entry->dest_mode_logical        = msg.arch_addr_lo.dest_mode_logical;
    121a:       09 f2                   or     %esi,%edx
    121c:       8d 0c 00                lea    (%rax,%rax,1),%ecx
        entry->ir_format                = msg.arch_addr_lo.dmar_format;
    121f:       c0 e8 04                shr    $0x4,%al
        entry->dest_mode_logical        = msg.arch_addr_lo.dest_mode_logical;
    1222:       83 e1 08                and    $0x8,%ecx
    1225:       09 ca                   or     %ecx,%edx
    1227:       88 53 01                mov    %dl,0x1(%rbx)
        entry->ir_format                = msg.arch_addr_lo.dmar_format;
    122a:       89 c2                   mov    %eax,%edx
        entry->ir_index_0_14            = msg.arch_addr_lo.dmar_index_0_14;
    122c:       8b 04 24                mov    (%rsp),%eax
    122f:       83 e2 01                and    $0x1,%edx
    1232:       c1 e8 05                shr    $0x5,%eax
    1235:       66 25 ff 7f             and    $0x7fff,%ax
    1239:       8d 0c 00                lea    (%rax,%rax,1),%ecx
    123c:       66 c1 e8 07             shr    $0x7,%ax
    1240:       88 43 07                mov    %al,0x7(%rbx)
    1243:       09 ca                   or     %ecx,%edx
}
    1245:       48 8b 44 24 10          mov    0x10(%rsp),%rax
    124a:       65 48 33 04 25 28 00    xor    %gs:0x28,%rax
    1251:       00 00 
        entry->ir_index_0_14            = msg.arch_addr_lo.dmar_index_0_14;
    1253:       88 53 06                mov    %dl,0x6(%rbx)
}
    1256:       75 06                   jne    125e <ioapic_setup_msg_from_msi+0x7e>
    1258:       48 83 c4 18             add    $0x18,%rsp
    125c:       5b                      pop    %rbx
    125d:       c3                      retq   
    125e:       e8 00 00 00 00          callq  1263 <ioapic_setup_msg_from_msi+0x83>
    1263:       0f 1f 00                nopl   (%rax)
    1266:       66 2e 0f 1f 84 00 00    nopw   %cs:0x0(%rax,%rax,1)
    126d:       00 00 00 


Still, this isn't really a fast path so I'm content to file the GCC PR
for the really *obvious* misses and let it take its course.

[-- Attachment #1.2: smime.p7s --]
[-- Type: application/x-pkcs7-signature, Size: 5174 bytes --]

[-- Attachment #2: Type: text/plain, Size: 156 bytes --]

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

RE: [PATCH v3 17/35] x86/pci/xen: Use msi_msg shadow structs

[David Laight]

From: David Woodhouse
> Sent: 25 October 2020 10:26
> To: David Laight <David.Laight@ACULAB.COM>; x86@kernel.org
> 
> On Sun, 2020-10-25 at 09:49 +0000, David Laight wrote:
> > Just looking at a random one of these patches...
> >
> > Does the compiler manage to optimise that reasonably?
> > Or does it generate a lot of shifts and masks as each
> > bitfield is set?
> >
> > The code generation for bitfields is often a lot worse
> > that that for |= setting bits in a word.
> 
> Indeed, it appears to be utterly appalling. That was one of my
> motivations for doing it with masks and shifts in the first place.

I thought it would be.

I'm not even sure using bitfields to map hardware registers
makes the code any more readable (or fool proof).

I suspect using #define constants and explicit |= and &= ~
is actually best - provided the names are descriptive enough.

If you set all the fields the compiler will merge the values
and do a single write - provided nothing you read might
alias the target.

The only way to get strongly typed integers is to cast them
to a structure pointer type.
Together with a static inline function to remove the casts
and | the values together it might make things fool proof.
But I've never tried it.

ISTR once doing something like that with error codes, but
it didn't ever make source control.

	David

-
Registered Address Lakeside, Bramley Road, Mount Farm, Milton Keynes, MK1 1PT, UK
Registration No: 1397386 (Wales)
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 18/35] x86/msi: Remove msidef.h

[David Woodhouse]

From: Thomas Gleixner <tglx@linutronix.de>

Nothing uses the macro maze anymore.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
---
 arch/x86/include/asm/msidef.h | 57 -----------------------------------
 1 file changed, 57 deletions(-)
 delete mode 100644 arch/x86/include/asm/msidef.h

diff --git a/arch/x86/include/asm/msidef.h b/arch/x86/include/asm/msidef.h
deleted file mode 100644
index ee2f8ccc32d0..000000000000
--- a/arch/x86/include/asm/msidef.h
+++ /dev/null
@@ -1,57 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef _ASM_X86_MSIDEF_H
-#define _ASM_X86_MSIDEF_H
-
-/*
- * Constants for Intel APIC based MSI messages.
- */
-
-/*
- * Shifts for MSI data
- */
-
-#define MSI_DATA_VECTOR_SHIFT		0
-#define  MSI_DATA_VECTOR_MASK		0x000000ff
-#define	 MSI_DATA_VECTOR(v)		(((v) << MSI_DATA_VECTOR_SHIFT) & \
-					 MSI_DATA_VECTOR_MASK)
-
-#define MSI_DATA_DELIVERY_MODE_SHIFT	8
-#define  MSI_DATA_DELIVERY_FIXED	(0 << MSI_DATA_DELIVERY_MODE_SHIFT)
-#define  MSI_DATA_DELIVERY_LOWPRI	(1 << MSI_DATA_DELIVERY_MODE_SHIFT)
-
-#define MSI_DATA_LEVEL_SHIFT		14
-#define	 MSI_DATA_LEVEL_DEASSERT	(0 << MSI_DATA_LEVEL_SHIFT)
-#define	 MSI_DATA_LEVEL_ASSERT		(1 << MSI_DATA_LEVEL_SHIFT)
-
-#define MSI_DATA_TRIGGER_SHIFT		15
-#define  MSI_DATA_TRIGGER_EDGE		(0 << MSI_DATA_TRIGGER_SHIFT)
-#define  MSI_DATA_TRIGGER_LEVEL		(1 << MSI_DATA_TRIGGER_SHIFT)
-
-/*
- * Shift/mask fields for msi address
- */
-
-#define MSI_ADDR_BASE_HI		0
-#define MSI_ADDR_BASE_LO		0xfee00000
-
-#define MSI_ADDR_DEST_MODE_SHIFT	2
-#define  MSI_ADDR_DEST_MODE_PHYSICAL	(0 << MSI_ADDR_DEST_MODE_SHIFT)
-#define	 MSI_ADDR_DEST_MODE_LOGICAL	(1 << MSI_ADDR_DEST_MODE_SHIFT)
-
-#define MSI_ADDR_REDIRECTION_SHIFT	3
-#define  MSI_ADDR_REDIRECTION_CPU	(0 << MSI_ADDR_REDIRECTION_SHIFT)
-					/* dedicated cpu */
-#define  MSI_ADDR_REDIRECTION_LOWPRI	(1 << MSI_ADDR_REDIRECTION_SHIFT)
-					/* lowest priority */
-
-#define MSI_ADDR_DEST_ID_SHIFT		12
-#define	 MSI_ADDR_DEST_ID_MASK		0x00ffff0
-#define  MSI_ADDR_DEST_ID(dest)		(((dest) << MSI_ADDR_DEST_ID_SHIFT) & \
-					 MSI_ADDR_DEST_ID_MASK)
-#define MSI_ADDR_EXT_DEST_ID(dest)	((dest) & 0xffffff00)
-
-#define MSI_ADDR_IR_EXT_INT		(1 << 4)
-#define MSI_ADDR_IR_SHV			(1 << 3)
-#define MSI_ADDR_IR_INDEX1(index)	((index & 0x8000) >> 13)
-#define MSI_ADDR_IR_INDEX2(index)	((index & 0x7fff) << 5)
-#endif /* _ASM_X86_MSIDEF_H */
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 19/35] x86/io_apic: Cleanup trigger/polarity helpers

[David Woodhouse]

From: Thomas Gleixner <tglx@linutronix.de>

'trigger' and 'polarity' are used throughout the I/O-APIC code for handling
the trigger type (edge/level) and the active low/high configuration. While
there are defines for initializing these variables and struct members, they
are not used consequently and the meaning of 'trigger' and 'polarity' is
opaque and confusing at best.

Rename them to 'is_level' and 'active_low' and make them boolean in various
structs so it's entirely clear what the meaning is.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
---
 arch/x86/include/asm/hw_irq.h       |   6 +-
 arch/x86/kernel/apic/io_apic.c      | 244 +++++++++++++---------------
 arch/x86/pci/intel_mid_pci.c        |   8 +-
 drivers/iommu/amd/iommu.c           |  10 +-
 drivers/iommu/intel/irq_remapping.c |   9 +-
 5 files changed, 130 insertions(+), 147 deletions(-)

diff --git a/arch/x86/include/asm/hw_irq.h b/arch/x86/include/asm/hw_irq.h
index a4aeeaace040..517847a94dbe 100644
--- a/arch/x86/include/asm/hw_irq.h
+++ b/arch/x86/include/asm/hw_irq.h
@@ -47,9 +47,9 @@ enum irq_alloc_type {
 struct ioapic_alloc_info {
 	int				pin;
 	int				node;
-	u32				trigger : 1;
-	u32				polarity : 1;
-	u32				valid : 1;
+	u32				is_level	: 1;
+	u32				active_low	: 1;
+	u32				valid		: 1;
 	struct IO_APIC_route_entry	*entry;
 };
 
diff --git a/arch/x86/kernel/apic/io_apic.c b/arch/x86/kernel/apic/io_apic.c
index c6d92d2570d0..24a7bba7cbf4 100644
--- a/arch/x86/kernel/apic/io_apic.c
+++ b/arch/x86/kernel/apic/io_apic.c
@@ -89,12 +89,12 @@ struct irq_pin_list {
 };
 
 struct mp_chip_data {
-	struct list_head irq_2_pin;
-	struct IO_APIC_route_entry entry;
-	int trigger;
-	int polarity;
+	struct list_head		irq_2_pin;
+	struct IO_APIC_route_entry	entry;
+	bool				is_level;
+	bool				active_low;
+	bool				isa_irq;
 	u32 count;
-	bool isa_irq;
 };
 
 struct mp_ioapic_gsi {
@@ -745,44 +745,7 @@ static int __init find_isa_irq_apic(int irq, int type)
 	return -1;
 }
 
-#ifdef CONFIG_EISA
-/*
- * EISA Edge/Level control register, ELCR
- */
-static int EISA_ELCR(unsigned int irq)
-{
-	if (irq < nr_legacy_irqs()) {
-		unsigned int port = 0x4d0 + (irq >> 3);
-		return (inb(port) >> (irq & 7)) & 1;
-	}
-	apic_printk(APIC_VERBOSE, KERN_INFO
-			"Broken MPtable reports ISA irq %d\n", irq);
-	return 0;
-}
-
-#endif
-
-/* ISA interrupts are always active high edge triggered,
- * when listed as conforming in the MP table. */
-
-#define default_ISA_trigger(idx)	(IOAPIC_EDGE)
-#define default_ISA_polarity(idx)	(IOAPIC_POL_HIGH)
-
-/* EISA interrupts are always polarity zero and can be edge or level
- * trigger depending on the ELCR value.  If an interrupt is listed as
- * EISA conforming in the MP table, that means its trigger type must
- * be read in from the ELCR */
-
-#define default_EISA_trigger(idx)	(EISA_ELCR(mp_irqs[idx].srcbusirq))
-#define default_EISA_polarity(idx)	default_ISA_polarity(idx)
-
-/* PCI interrupts are always active low level triggered,
- * when listed as conforming in the MP table. */
-
-#define default_PCI_trigger(idx)	(IOAPIC_LEVEL)
-#define default_PCI_polarity(idx)	(IOAPIC_POL_LOW)
-
-static int irq_polarity(int idx)
+static bool irq_active_low(int idx)
 {
 	int bus = mp_irqs[idx].srcbus;
 
@@ -791,90 +754,139 @@ static int irq_polarity(int idx)
 	 */
 	switch (mp_irqs[idx].irqflag & MP_IRQPOL_MASK) {
 	case MP_IRQPOL_DEFAULT:
-		/* conforms to spec, ie. bus-type dependent polarity */
-		if (test_bit(bus, mp_bus_not_pci))
-			return default_ISA_polarity(idx);
-		else
-			return default_PCI_polarity(idx);
+		/*
+		 * Conforms to spec, ie. bus-type dependent polarity.  PCI
+		 * defaults to low active. [E]ISA defaults to high active.
+		 */
+		return !test_bit(bus, mp_bus_not_pci);
 	case MP_IRQPOL_ACTIVE_HIGH:
-		return IOAPIC_POL_HIGH;
+		return false;
 	case MP_IRQPOL_RESERVED:
 		pr_warn("IOAPIC: Invalid polarity: 2, defaulting to low\n");
 		fallthrough;
 	case MP_IRQPOL_ACTIVE_LOW:
 	default: /* Pointless default required due to do gcc stupidity */
-		return IOAPIC_POL_LOW;
+		return true;
 	}
 }
 
 #ifdef CONFIG_EISA
-static int eisa_irq_trigger(int idx, int bus, int trigger)
+/*
+ * EISA Edge/Level control register, ELCR
+ */
+static bool EISA_ELCR(unsigned int irq)
+{
+	if (irq < nr_legacy_irqs()) {
+		unsigned int port = 0x4d0 + (irq >> 3);
+		return (inb(port) >> (irq & 7)) & 1;
+	}
+	apic_printk(APIC_VERBOSE, KERN_INFO
+			"Broken MPtable reports ISA irq %d\n", irq);
+	return false;
+}
+
+/*
+ * EISA interrupts are always active high and can be edge or level
+ * triggered depending on the ELCR value.  If an interrupt is listed as
+ * EISA conforming in the MP table, that means its trigger type must be
+ * read in from the ELCR.
+ */
+static bool eisa_irq_is_level(int idx, int bus, bool level)
 {
 	switch (mp_bus_id_to_type[bus]) {
 	case MP_BUS_PCI:
 	case MP_BUS_ISA:
-		return trigger;
+		return level;
 	case MP_BUS_EISA:
-		return default_EISA_trigger(idx);
+		return EISA_ELCR(mp_irqs[idx].srcbusirq);
 	}
 	pr_warn("IOAPIC: Invalid srcbus: %d defaulting to level\n", bus);
-	return IOAPIC_LEVEL;
+	return true;
 }
 #else
-static inline int eisa_irq_trigger(int idx, int bus, int trigger)
+static inline int eisa_irq_is_level(int idx, int bus, bool level)
 {
-	return trigger;
+	return level;
 }
 #endif
 
-static int irq_trigger(int idx)
+static bool irq_is_level(int idx)
 {
 	int bus = mp_irqs[idx].srcbus;
-	int trigger;
+	bool level;
 
 	/*
 	 * Determine IRQ trigger mode (edge or level sensitive):
 	 */
 	switch (mp_irqs[idx].irqflag & MP_IRQTRIG_MASK) {
 	case MP_IRQTRIG_DEFAULT:
-		/* conforms to spec, ie. bus-type dependent trigger mode */
-		if (test_bit(bus, mp_bus_not_pci))
-			trigger = default_ISA_trigger(idx);
-		else
-			trigger = default_PCI_trigger(idx);
+		/*
+		 * Conforms to spec, ie. bus-type dependent trigger
+		 * mode. PCI defaults to egde, ISA to level.
+		 */
+		level = test_bit(bus, mp_bus_not_pci);
 		/* Take EISA into account */
-		return eisa_irq_trigger(idx, bus, trigger);
+		return eisa_irq_is_level(idx, bus, level);
 	case MP_IRQTRIG_EDGE:
-		return IOAPIC_EDGE;
+		return false;
 	case MP_IRQTRIG_RESERVED:
 		pr_warn("IOAPIC: Invalid trigger mode 2 defaulting to level\n");
 		fallthrough;
 	case MP_IRQTRIG_LEVEL:
 	default: /* Pointless default required due to do gcc stupidity */
-		return IOAPIC_LEVEL;
+		return true;
 	}
 }
 
+static int __acpi_get_override_irq(u32 gsi, bool *trigger, bool *polarity)
+{
+	int ioapic, pin, idx;
+
+	if (skip_ioapic_setup)
+		return -1;
+
+	ioapic = mp_find_ioapic(gsi);
+	if (ioapic < 0)
+		return -1;
+
+	pin = mp_find_ioapic_pin(ioapic, gsi);
+	if (pin < 0)
+		return -1;
+
+	idx = find_irq_entry(ioapic, pin, mp_INT);
+	if (idx < 0)
+		return -1;
+
+	*trigger = irq_is_level(idx);
+	*polarity = irq_active_low(idx);
+	return 0;
+}
+
+#ifdef CONFIG_ACPI
+int acpi_get_override_irq(u32 gsi, int *is_level, int *active_low)
+{
+	*is_level = *active_low = 0;
+	return __acpi_get_override_irq(gsi, (bool *)is_level,
+				       (bool *)active_low);
+}
+#endif
+
 void ioapic_set_alloc_attr(struct irq_alloc_info *info, int node,
 			   int trigger, int polarity)
 {
 	init_irq_alloc_info(info, NULL);
 	info->type = X86_IRQ_ALLOC_TYPE_IOAPIC;
 	info->ioapic.node = node;
-	info->ioapic.trigger = trigger;
-	info->ioapic.polarity = polarity;
+	info->ioapic.is_level = trigger;
+	info->ioapic.active_low = polarity;
 	info->ioapic.valid = 1;
 }
 
-#ifndef CONFIG_ACPI
-int acpi_get_override_irq(u32 gsi, int *trigger, int *polarity);
-#endif
-
 static void ioapic_copy_alloc_attr(struct irq_alloc_info *dst,
 				   struct irq_alloc_info *src,
 				   u32 gsi, int ioapic_idx, int pin)
 {
-	int trigger, polarity;
+	bool level, pol_low;
 
 	copy_irq_alloc_info(dst, src);
 	dst->type = X86_IRQ_ALLOC_TYPE_IOAPIC;
@@ -883,20 +895,20 @@ static void ioapic_copy_alloc_attr(struct irq_alloc_info *dst,
 	dst->ioapic.valid = 1;
 	if (src && src->ioapic.valid) {
 		dst->ioapic.node = src->ioapic.node;
-		dst->ioapic.trigger = src->ioapic.trigger;
-		dst->ioapic.polarity = src->ioapic.polarity;
+		dst->ioapic.is_level = src->ioapic.is_level;
+		dst->ioapic.active_low = src->ioapic.active_low;
 	} else {
 		dst->ioapic.node = NUMA_NO_NODE;
-		if (acpi_get_override_irq(gsi, &trigger, &polarity) >= 0) {
-			dst->ioapic.trigger = trigger;
-			dst->ioapic.polarity = polarity;
+		if (__acpi_get_override_irq(gsi, &level, &pol_low) >= 0) {
+			dst->ioapic.is_level = level;
+			dst->ioapic.active_low = pol_low;
 		} else {
 			/*
 			 * PCI interrupts are always active low level
 			 * triggered.
 			 */
-			dst->ioapic.trigger = IOAPIC_LEVEL;
-			dst->ioapic.polarity = IOAPIC_POL_LOW;
+			dst->ioapic.is_level = true;
+			dst->ioapic.active_low = true;
 		}
 	}
 }
@@ -906,12 +918,12 @@ static int ioapic_alloc_attr_node(struct irq_alloc_info *info)
 	return (info && info->ioapic.valid) ? info->ioapic.node : NUMA_NO_NODE;
 }
 
-static void mp_register_handler(unsigned int irq, unsigned long trigger)
+static void mp_register_handler(unsigned int irq, bool level)
 {
 	irq_flow_handler_t hdl;
 	bool fasteoi;
 
-	if (trigger) {
+	if (level) {
 		irq_set_status_flags(irq, IRQ_LEVEL);
 		fasteoi = true;
 	} else {
@@ -933,14 +945,14 @@ static bool mp_check_pin_attr(int irq, struct irq_alloc_info *info)
 	 * pin with real trigger and polarity attributes.
 	 */
 	if (irq < nr_legacy_irqs() && data->count == 1) {
-		if (info->ioapic.trigger != data->trigger)
-			mp_register_handler(irq, info->ioapic.trigger);
-		data->entry.trigger = data->trigger = info->ioapic.trigger;
-		data->entry.polarity = data->polarity = info->ioapic.polarity;
+		if (info->ioapic.is_level != data->is_level)
+			mp_register_handler(irq, info->ioapic.is_level);
+		data->entry.trigger = data->is_level = info->ioapic.is_level;
+		data->entry.polarity = data->active_low = info->ioapic.active_low;
 	}
 
-	return data->trigger == info->ioapic.trigger &&
-	       data->polarity == info->ioapic.polarity;
+	return data->is_level == info->ioapic.is_level &&
+	       data->active_low == info->ioapic.active_low;
 }
 
 static int alloc_irq_from_domain(struct irq_domain *domain, int ioapic, u32 gsi,
@@ -2179,9 +2191,9 @@ static inline void __init check_timer(void)
 			 * so only need to unmask if it is level-trigger
 			 * do we really have level trigger timer?
 			 */
-			int idx;
-			idx = find_irq_entry(apic1, pin1, mp_INT);
-			if (idx != -1 && irq_trigger(idx))
+			int idx = find_irq_entry(apic1, pin1, mp_INT);
+
+			if (idx != -1 && irq_is_level(idx))
 				unmask_ioapic_irq(irq_get_irq_data(0));
 		}
 		irq_domain_deactivate_irq(irq_data);
@@ -2588,30 +2600,6 @@ static int io_apic_get_version(int ioapic)
 	return reg_01.bits.version;
 }
 
-int acpi_get_override_irq(u32 gsi, int *trigger, int *polarity)
-{
-	int ioapic, pin, idx;
-
-	if (skip_ioapic_setup)
-		return -1;
-
-	ioapic = mp_find_ioapic(gsi);
-	if (ioapic < 0)
-		return -1;
-
-	pin = mp_find_ioapic_pin(ioapic, gsi);
-	if (pin < 0)
-		return -1;
-
-	idx = find_irq_entry(ioapic, pin, mp_INT);
-	if (idx < 0)
-		return -1;
-
-	*trigger = irq_trigger(idx);
-	*polarity = irq_polarity(idx);
-	return 0;
-}
-
 /*
  * This function updates target affinity of IOAPIC interrupts to include
  * the CPUs which came online during SMP bringup.
@@ -2935,13 +2923,13 @@ static void mp_irqdomain_get_attr(u32 gsi, struct mp_chip_data *data,
 				  struct irq_alloc_info *info)
 {
 	if (info && info->ioapic.valid) {
-		data->trigger = info->ioapic.trigger;
-		data->polarity = info->ioapic.polarity;
-	} else if (acpi_get_override_irq(gsi, &data->trigger,
-					 &data->polarity) < 0) {
+		data->is_level = info->ioapic.is_level;
+		data->active_low = info->ioapic.active_low;
+	} else if (__acpi_get_override_irq(gsi, &data->is_level,
+					   &data->active_low) < 0) {
 		/* PCI interrupts are always active low level triggered. */
-		data->trigger = IOAPIC_LEVEL;
-		data->polarity = IOAPIC_POL_LOW;
+		data->is_level = true;
+		data->active_low = true;
 	}
 }
 
@@ -2953,16 +2941,13 @@ static void mp_setup_entry(struct irq_cfg *cfg, struct mp_chip_data *data,
 	entry->dest_mode     = apic->dest_mode_logical;
 	entry->dest	     = cfg->dest_apicid;
 	entry->vector	     = cfg->vector;
-	entry->trigger	     = data->trigger;
-	entry->polarity	     = data->polarity;
+	entry->trigger	     = data->is_level;
+	entry->polarity	     = data->active_low;
 	/*
 	 * Mask level triggered irqs. Edge triggered irqs are masked
 	 * by the irq core code in case they fire.
 	 */
-	if (data->trigger == IOAPIC_LEVEL)
-		entry->mask = IOAPIC_MASKED;
-	else
-		entry->mask = IOAPIC_UNMASKED;
+	entry->mask = data->is_level;
 }
 
 int mp_irqdomain_alloc(struct irq_domain *domain, unsigned int virq,
@@ -3010,7 +2995,7 @@ int mp_irqdomain_alloc(struct irq_domain *domain, unsigned int virq,
 	local_irq_save(flags);
 	if (info->ioapic.entry)
 		mp_setup_entry(cfg, data, info->ioapic.entry);
-	mp_register_handler(virq, data->trigger);
+	mp_register_handler(virq, data->is_level);
 	if (virq < nr_legacy_irqs())
 		legacy_pic->mask(virq);
 	local_irq_restore(flags);
@@ -3018,7 +3003,8 @@ int mp_irqdomain_alloc(struct irq_domain *domain, unsigned int virq,
 	apic_printk(APIC_VERBOSE, KERN_DEBUG
 		    "IOAPIC[%d]: Set routing entry (%d-%d -> 0x%x -> IRQ %d Mode:%i Active:%i Dest:%d)\n",
 		    ioapic, mpc_ioapic_id(ioapic), pin, cfg->vector,
-		    virq, data->trigger, data->polarity, cfg->dest_apicid);
+		    virq, data->is_level, data->active_low,
+		    cfg->dest_apicid);
 
 	return 0;
 }
diff --git a/arch/x86/pci/intel_mid_pci.c b/arch/x86/pci/intel_mid_pci.c
index 00c62115f39c..3709afae7c77 100644
--- a/arch/x86/pci/intel_mid_pci.c
+++ b/arch/x86/pci/intel_mid_pci.c
@@ -214,7 +214,7 @@ static int pci_write(struct pci_bus *bus, unsigned int devfn, int where,
 static int intel_mid_pci_irq_enable(struct pci_dev *dev)
 {
 	struct irq_alloc_info info;
-	int polarity;
+	bool polarity_low;
 	int ret;
 	u8 gsi;
 
@@ -229,7 +229,7 @@ static int intel_mid_pci_irq_enable(struct pci_dev *dev)
 
 	switch (intel_mid_identify_cpu()) {
 	case INTEL_MID_CPU_CHIP_TANGIER:
-		polarity = IOAPIC_POL_HIGH;
+		polarity_low = false;
 
 		/* Special treatment for IRQ0 */
 		if (gsi == 0) {
@@ -251,11 +251,11 @@ static int intel_mid_pci_irq_enable(struct pci_dev *dev)
 		}
 		break;
 	default:
-		polarity = IOAPIC_POL_LOW;
+		polarity_low = true;
 		break;
 	}
 
-	ioapic_set_alloc_attr(&info, dev_to_node(&dev->dev), 1, polarity);
+	ioapic_set_alloc_attr(&info, dev_to_node(&dev->dev), 1, polarity_low);
 
 	/*
 	 * MRST only have IOAPIC, the PCI irq lines are 1:1 mapped to
diff --git a/drivers/iommu/amd/iommu.c b/drivers/iommu/amd/iommu.c
index 473de0920b64..b0e5210e53b2 100644
--- a/drivers/iommu/amd/iommu.c
+++ b/drivers/iommu/amd/iommu.c
@@ -3687,13 +3687,11 @@ static void irq_remapping_prepare_irte(struct amd_ir_data *data,
 		entry = info->ioapic.entry;
 		info->ioapic.entry = NULL;
 		memset(entry, 0, sizeof(*entry));
-		entry->vector        = index;
-		entry->mask          = 0;
-		entry->trigger       = info->ioapic.trigger;
-		entry->polarity      = info->ioapic.polarity;
+		entry->vector	= index;
+		entry->trigger	= info->ioapic.is_level;
+		entry->polarity	= info->ioapic.active_low;
 		/* Mask level triggered irqs. */
-		if (info->ioapic.trigger)
-			entry->mask = 1;
+		entry->mask	= info->ioapic.is_level;
 		break;
 
 	case X86_IRQ_ALLOC_TYPE_HPET:
diff --git a/drivers/iommu/intel/irq_remapping.c b/drivers/iommu/intel/irq_remapping.c
index 30269b738fa5..54ca69333445 100644
--- a/drivers/iommu/intel/irq_remapping.c
+++ b/drivers/iommu/intel/irq_remapping.c
@@ -1306,11 +1306,10 @@ static void intel_irq_remapping_prepare_irte(struct intel_ir_data *data,
 		 * irq handler will do the explicit EOI to the io-apic.
 		 */
 		entry->vector	= info->ioapic.pin;
-		entry->mask	= 0;			/* enable IRQ */
-		entry->trigger	= info->ioapic.trigger;
-		entry->polarity	= info->ioapic.polarity;
-		if (info->ioapic.trigger)
-			entry->mask = 1; /* Mask level triggered irqs. */
+		entry->trigger	= info->ioapic.is_level;
+		entry->polarity	= info->ioapic.active_low;
+		/* Mask level triggered irqs. */
+		entry->mask	= info->ioapic.is_level;
 		break;
 
 	case X86_IRQ_ALLOC_TYPE_HPET:
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

Re: [PATCH v3 19/35] x86/io_apic: Cleanup trigger/polarity helpers

[Qian Cai]

On Sat, 2020-10-24 at 22:35 +0100, David Woodhouse wrote:
> From: Thomas Gleixner <tglx@linutronix.de>
> 
> 'trigger' and 'polarity' are used throughout the I/O-APIC code for handling
> the trigger type (edge/level) and the active low/high configuration. While
> there are defines for initializing these variables and struct members, they
> are not used consequently and the meaning of 'trigger' and 'polarity' is
> opaque and confusing at best.
> 
> Rename them to 'is_level' and 'active_low' and make them boolean in various
> structs so it's entirely clear what the meaning is.
> 
> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
> Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
> ---
>  arch/x86/include/asm/hw_irq.h       |   6 +-
>  arch/x86/kernel/apic/io_apic.c      | 244 +++++++++++++---------------
>  arch/x86/pci/intel_mid_pci.c        |   8 +-
>  drivers/iommu/amd/iommu.c           |  10 +-
>  drivers/iommu/intel/irq_remapping.c |   9 +-
>  5 files changed, 130 insertions(+), 147 deletions(-)

Reverting the rest of patchset up to this commit on next-20201109 fixed an
endless soft-lockups issue booting an AMD server below. I noticed that the
failed boots always has this IOMMU IO_PAGE_FAULT before those soft-lockups:

[ 3404.093354][    T1] AMD-Vi: Interrupt remapping enabled
[ 3404.098593][    T1] AMD-Vi: Virtual APIC enabled
[ 3404.107783][  T340] pci 0000:00:14.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0000 address=0xfffffffdf8020200 flags=0x0008]
[ 3404.120644][    T1] AMD-Vi: Lazy IO/TLB flushing enabled
[ 3404.126011][    T1] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 3404.133173][    T1] software IO TLB: mapped [mem 0x0000000068dcf000-0x000000006cdcf000] (64MB)

.config (if ever matters):
https://cailca.coding.net/public/linux/mm/git/files/master/x86.config

good boot dmesg (with the commits reverted):
http://people.redhat.com/qcai/dmesg.txt

== system info ==
Dell Poweredge R6415
AMD EPYC 7401P 24-Core Processor
24576 MB memory, 239 GB disk space

[  OK  ] Started Flush Journal to Persistent Storage.
[  OK  ] Started udev Kernel Device Manager.
[  OK  ] Started udev Coldplug all Devices.
[  OK  ] Started Monitoring of LVM2 mirrors,…sing dmeventd or progress polling.
[  OK  ] Reached target Local File Systems (Pre).
         Mounting /boot...
[  OK  ] Created slice system-lvm2\x2dpvscan.slice.
[ 3740.376500][ T1058] XFS (sda1): Mounting V5 Filesystem
[ 3740.438474][ T1058] XFS (sda1): Ending clean mount
[ 3765.159433][    C0] watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [systemd:1]
[ 3765.166929][    C0] Modules linked in: acpi_cpufreq(+) ip_tables x_tables sd_mod ahci libahci tg3 bnxt_en megaraid_sas libata firmware_class libphy dm_mirror dm_region_hash dm_log dm_mod
[ 3765.183576][    C0] irq event stamp: 26230104
[ 3765.187954][    C0] hardirqs last  enabled at (26230103): [<ffffffff82800b9e>] asm_common_interrupt+0x1e/0x40
[ 3765.197873][    C0] hardirqs last disabled at (26230104): [<ffffffff8277e45a>] sysvec_apic_timer_interrupt+0xa/0xa0
[ 3765.208303][    C0] softirqs last  enabled at (26202664): [<ffffffff82a0061b>] __do_softirq+0x61b/0x95d
[ 3765.217699][    C0] softirqs last disabled at (26202591): [<ffffffff82800ec2>] asm_call_irq_on_stack+0x12/0x20
[ 3765.227702][    C0] CPU: 0 PID: 1 Comm: systemd Not tainted 5.10.0-rc2-next-20201109+ #2
[ 3765.235793][    C0] Hardware name: Dell Inc. PowerEdge R6415/07YXFK, BIOS 1.9.3 06/25/2019
[ 3765.244065][    C0] RIP: 0010:lock_acquire+0x1f4/0x820
lock_acquire at kernel/locking/lockdep.c:5404
[ 3765.249211][    C0] Code: ff ff ff 48 83 c4 20 65 0f c1 05 a7 ba 9e 7e 83 f8 01 4c 8b 54 24 08 0f 85 60 04 00 00 41 52 9d 48 b8 00 00 00 00 00 fc ff df <48> 01 c3 c7 03 00 00 00 00 c7 43 08 00 00 00 00 48 8b0
[ 3765.268657][    C0] RSP: 0018:ffffc9000006f9f8 EFLAGS: 00000246
[ 3765.274587][    C0] RAX: dffffc0000000000 RBX: 1ffff9200000df42 RCX: 1ffff9200000df28
[ 3765.282420][    C0] RDX: 1ffff11020645769 RSI: 00000000ffffffff RDI: 0000000000000001
[ 3765.290256][    C0] RBP: 0000000000000001 R08: fffffbfff164cb10 R09: fffffbfff164cb10
[ 3765.298090][    C0] R10: 0000000000000246 R11: fffffbfff164cb0f R12: ffff88812be555b0
[ 3765.305922][    C0] R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
[ 3765.313750][    C0] FS:  00007f12bb8c59c0(0000) GS:ffff8881b7000000(0000) knlGS:0000000000000000
[ 3765.322537][    C0] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 3765.328985][    C0] CR2: 00007f0c2d828fd0 CR3: 000000011868a000 CR4: 00000000003506f0
[ 3765.336820][    C0] Call Trace:
[ 3765.339979][    C0]  ? rcu_read_unlock+0x40/0x40
[ 3765.344609][    C0]  __d_move+0x2a2/0x16f0
__seqprop_spinlock_assert at include/linux/seqlock.h:277
(inlined by) __d_move at fs/dcache.c:2861
[ 3765.348711][    C0]  ? d_move+0x47/0x70
[ 3765.352560][    C0]  ? _raw_spin_unlock+0x1a/0x30
[ 3765.357275][    C0]  d_move+0x47/0x70
write_seqcount_t_end at include/linux/seqlock.h:560
(inlined by) write_sequnlock at include/linux/seqlock.h:901
(inlined by) d_move at fs/dcache.c:2916
[ 3765.360951][    C0]  ? vfs_rename+0x9ac/0x1270
[ 3765.365402][    C0]  vfs_rename+0x9ac/0x1270
vfs_rename at fs/namei.c:4330
[ 3765.369687][    C0]  ? vfs_link+0x830/0x830
[ 3765.373878][    C0]  ? do_renameat2+0x58c/0x930
[ 3765.378419][    C0]  do_renameat2+0x58c/0x930
do_renameat2 at fs/namei.c:4455
[ 3765.382790][    C0]  ? __ia32_sys_link+0x80/0x80
[ 3765.387418][    C0]  ? rcu_read_lock_bh_held+0xb0/0xb0
[ 3765.392563][    C0]  ? rcu_read_lock_sched_held+0x9c/0xd0
[ 3765.397965][    C0]  ? rcu_read_lock_bh_held+0xb0/0xb0
[ 3765.403112][    C0]  ? lockdep_hardirqs_on_prepare+0x27c/0x3d0
[ 3765.408955][    C0]  ? trace_hardirqs_on+0x1c/0x150
[ 3765.413841][    C0]  ? asm_common_interrupt+0x1e/0x40
[ 3765.418905][    C0]  ? strncpy_from_user+0x14c/0x330
[ 3765.423878][    C0]  ? strncpy_from_user+0x6b/0x330
[ 3765.428764][    C0]  ? getname_flags+0x88/0x3e0
[ 3765.433307][    C0]  __x64_sys_rename+0x75/0x90
__x64_sys_rename at fs/namei.c:4504
[ 3765.437848][    C0]  do_syscall_64+0x33/0x40
[ 3765.442129][    C0]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 3765.447882][    C0] RIP: 0033:0x7f12b9b759eb
[ 3765.452166][    C0] Code: e8 5a 0a 08 00 85 c0 0f 95 c0 0f b6 c0 f7 d8 5b c3 66 0f 1f 44 00 00 b8 ff ff ff ff 5b c3 90 f3 0f 1e fa b8 52 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 05 c3 0f 1f 40 00 48 8b 15 69 e48
[ 3765.471611][    C0] RSP: 002b:00007fff76252538 EFLAGS: 00000246 ORIG_RAX: 0000000000000052
[ 3765.479880][    C0] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f12b9b759eb
[ 3765.487715][    C0] RDX: 000055ea2997f400 RSI: 00007fff76252570 RDI: 000055ea2997f450
[ 3765.495548][    C0] RBP: 00007fff76252570 R08: 0000000000000000 R09: 0000000065732e32
[ 3765.503374][    C0] R10: 0000000000000003 R11: 0000000000000246 R12: 000055ea2996fcf8
[ 3765.511201][    C0] R13: 000055ea2996fcf8 R14: 000055ea277097f0 R15: 0000000000000000
[ 3765.939428][   C14] watchdog: BUG: soft lockup - CPU#14 stuck for 23s! [systemd-udevd:976]
[ 3765.947707][   C14] Modules linked in: acpi_cpufreq(+) ip_tables x_tables sd_mod ahci libahci tg3 bnxt_en megaraid_sas libata firmware_class libphy dm_mirror dm_region_hash dm_log dm_mod
[ 3765.964357][   C14] irq event stamp: 535074
[ 3765.968564][   C14] hardirqs last  enabled at (535073): [<ffffffff82800c42>] asm_sysvec_apic_timer_interrupt+0x12/0x20
[ 3765.979266][   C14] hardirqs last disabled at (535074): [<ffffffff8277e45a>] sysvec_apic_timer_interrupt+0xa/0xa0
[ 3765.989532][   C14] softirqs last  enabled at (535072): [<ffffffff82a0061b>] __do_softirq+0x61b/0x95d
[ 3765.998761][   C14] softirqs last disabled at (535067): [<ffffffff82800ec2>] asm_call_irq_on_stack+0x12/0x20
[ 3766.008590][   C14] CPU: 14 PID: 976 Comm: systemd-udevd Tainted: G             L    5.10.0-rc2-next-20201109+ #2
[ 3766.018851][   C14] Hardware name: Dell Inc. PowerEdge R6415/07YXFK, BIOS 1.9.3 06/25/2019
[ 3766.027130][   C14] RIP: 0010:path_init+0x1dd/0x1380
__seqprop_spinlock_sequence at include/linux/seqlock.h:277
(inlined by) path_init at fs/namei.c:2219
[ 3766.032112][   C14] Code: 03 0f 8e 79 11 00 00 44 8b 3d 5f f0 6e 01 41 f6 c7 01 74 2e 48 b8 00 00 00 00 00 fc ff df 48 89 d1 48 c1 e9 03 48 01 c1 f3 90 <0f> b6 01 84 c0 74 08 3c 03 0f 8e 9a 0d 00 00 44 8b 3a1
[ 3766.051565][   C14] RSP: 0018:ffffc90006bdfa78 EFLAGS: 00000202
[ 3766.057493][   C14] RAX: 0000000000000000 RBX: ffffc90006bdfcc0 RCX: fffffbfff06426b0
[ 3766.065330][   C14] RDX: ffffffff83213580 RSI: 00000000d93ef353 RDI: ffffc90006bdfd00
[ 3766.073163][   C14] RBP: ffffc90006bdfb08 R08: fffffbfff164cb0d R09: fffffbfff164cb0d
[ 3766.080997][   C14] R10: 0000000000000246 R11: fffffbfff164cb0c R12: ffff8881159d0060
[ 3766.088831][   C14] R13: ffffc90006bdfcf8 R14: 0000000000000041 R15: 000000000000039d
[ 3766.096665][   C14] FS:  00007f0c2ec45980(0000) GS:ffff88866dec0000(0000) knlGS:0000000000000000
[ 3766.105454][   C14] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 3766.111900][   C14] CR2: 00007f79350ceb84 CR3: 0000000160a84000 CR4: 00000000003506e0
[ 3766.119737][   C14] Call Trace:
[ 3766.122899][   C14]  ? debug_mutex_init+0x31/0x60
[ 3766.127614][   C14]  path_openat+0x154/0x1b00
path_openat at fs/namei.c:3364
[ 3766.131988][   C14]  ? rcu_read_lock_held+0xb0/0xb0
[ 3766.136881][   C14]  ? __lock_acquire+0x1dad/0x3890
[ 3766.141767][   C14]  ? path_parentat.isra.62+0x190/0x190
[ 3766.147090][   C14]  ? rcu_read_lock_sched_held+0x9c/0xd0
[ 3766.152496][   C14]  ? rcu_read_lock_bh_held+0xb0/0xb0
[ 3766.157646][   C14]  do_filp_open+0x171/0x240
[ 3766.162017][   C14]  ? may_open_dev+0xc0/0xc0
[ 3766.166388][   C14]  ? lock_downgrade+0x700/0x700
[ 3766.171104][   C14]  ? rcu_read_unlock+0x40/0x40
[ 3766.175735][   C14]  ? rwlock_bug.part.1+0x90/0x90
[ 3766.180543][   C14]  ? __check_object_size+0x454/0x670
[ 3766.185692][   C14]  ? do_raw_spin_unlock+0x4f/0x250
[ 3766.190668][   C14]  ? __alloc_fd+0x184/0x500
[ 3766.195031][   C14]  do_sys_openat2+0x2db/0x5b0
[ 3766.199576][   C14]  ? memset+0x1f/0x40
[ 3766.203422][   C14]  ? file_open_root+0x200/0x200
[ 3766.208136][   C14]  do_sys_open+0x85/0xd0
[ 3766.212245][   C14]  ? filp_open+0x50/0x50
[ 3766.216353][   C14]  ? syscall_trace_enter.isra.21+0x54/0x1f0
[ 3766.222107][   C14]  do_syscall_64+0x33/0x40
[ 3766.226389][   C14]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 3766.232145][   C14] RIP: 0033:0x7f0c2d828552
[ 3766.236426][   C14] Code: 25 00 00 41 00 3d 00 00 41 00 74 4c 48 8d 05 15 50 2d 00 8b 00 85 c0 75 6d 89 f2 b8 01 01 00 00 48 89 fe bf 9c ff ff ff 0f 05 <48> 3d 00 f0 ff ff 0f 87 a2 00 00 00 48 8b 4c 24 28 645
[ 3766.255873][   C14] RSP: 002b:00007ffc65d36000 EFLAGS: 00000246 ORIG_RAX: 0000000000000101
[ 3766.264147][   C14] RAX: ffffffffffffffda RBX: 0000564d81e50770 RCX: 00007f0c2d828552
[ 3766.271982][   C14] RDX: 0000000000080000 RSI: 00007ffc65d36150 RDI: 00000000ffffff9c
[ 3766.279817][   C14] RBP: 0000000000000008 R08: 0000000000000008 R09: 0000000000000001
[ 3766.287651][   C14] R10: 0000000000000000 R11: 0000000000000246 R12: 00007f0c2e733347
[ 3766.295486][   C14] R13: 00007f0c2e733347 R14: 0000000000000001 R15: 0000564d81e2d1b8
[ 3766.469430][   C28] watchdog: BUG: soft lockup - CPU#28 stuck for 22s! [mount:1058]
[ 3766.477105][   C28] Modules linked in: acpi_cpufreq(+) ip_tables x_tables sd_mod ahci libahci tg3 bnxt_en megaraid_sas libata firmware_class libphy dm_mirror dm_region_hash dm_log dm_mod
[ 3766.493753][   C28] irq event stamp: 88756
[ 3766.497868][   C28] hardirqs last  enabled at (88755): [<ffffffff82800c42>] asm_sysvec_apic_timer_interrupt+0x12/0x20
[ 3766.508481][   C28] hardirqs last disabled at (88756): [<ffffffff8277e45a>] sysvec_apic_timer_interrupt+0xa/0xa0
[ 3766.518665][   C28] softirqs last  enabled at (88748): [<ffffffff82a0061b>] __do_softirq+0x61b/0x95d
[ 3766.527805][   C28] softirqs last disabled at (88743): [<ffffffff82800ec2>] asm_call_irq_on_stack+0x12/0x20
[ 3766.537550][   C28] CPU: 28 PID: 1058 Comm: mount Tainted: G             L    5.10.0-rc2-next-20201109+ #2
[ 3766.547210][   C28] Hardware name: Dell Inc. PowerEdge R6415/07YXFK, BIOS 1.9.3 06/25/2019
[ 3766.555482][   C28] RIP: 0010:prepend_path.isra.6+0x349/0xdb0
__seqprop_spinlock_sequence at include/linux/seqlock.h:277
(inlined by) read_seqbegin at include/linux/seqlock.h:838
(inlined by) read_seqbegin_or_lock at include/linux/seqlock.h:1142
(inlined by) read_seqbegin_or_lock at include/linux/seqlock.h:1139
(inlined by) prepend_path at fs/d_path.c:99
[ 3766.561241][   C28] Code: 95 f0 fe ff ff 5a 41 54 9d 41 0f b6 55 00 84 d2 74 09 80 fa 03 0f 8e 75 09 00 00 45 8b 26 41 f6 c4 01 0f 84 5b 05 00 00 f3 90 <41> 0f b6 55 00 84 d2 74 e8 80 fa 03 7f e3 4c 89 f7 4ce
[ 3766.580687][   C28] RSP: 0018:ffffc9000670fa18 EFLAGS: 00000202
[ 3766.586618][   C28] RAX: ffff88812bd7d070 RBX: dffffc0000000000 RCX: 1ffff1102a164dc8
[ 3766.594449][   C28] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffff81bafabb
[ 3766.602287][   C28] RBP: ffffc9000670fb68 R08: 0000000000000001 R09: ffffffff81bb033d
[ 3766.610118][   C28] R10: ffff8881517d8340 R11: fffffbfff14b86e4 R12: 000000000000039d
[ 3766.617956][   C28] R13: fffffbfff06426b0 R14: ffffffff83213580 R15: ffffc9000670fbc0
[ 3766.625789][   C28] FS:  00007f96bb7a6080(0000) GS:ffff8881b71c0000(0000) knlGS:0000000000000000
[ 3766.634579][   C28] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 3766.641026][   C28] CR2: 00007f96ba7343f0 CR3: 0000000146c76000 CR4: 00000000003506e0
[ 3766.648859][   C28] Call Trace:
[ 3766.652016][   C28]  ? dentry_path_raw+0x10/0x10
[ 3766.656645][   C28]  ? rcu_read_unlock+0x40/0x40
[ 3766.661276][   C28]  ? memcpy+0x38/0x60
[ 3766.665128][   C28]  d_path+0x3fd/0x660
[ 3766.668976][   C28]  ? prepend_path.isra.6+0xdb0/0xdb0
[ 3766.674129][   C28]  ? __alloc_pages_nodemask+0x650/0x760
[ 3766.679543][   C28]  ? __alloc_pages_slowpath.constprop.112+0x2120/0x2120
[ 3766.686345][   C28]  mnt_warn_timestamp_expiry+0x25a/0x270
mnt_warn_timestamp_expiry at fs/namespace.c:2555 (discriminator 1)
[ 3766.691839][   C28]  ? get_mountpoint+0x370/0x370
[ 3766.696554][   C28]  ? do_raw_spin_unlock+0x4f/0x250
[ 3766.701536][   C28]  ? _raw_spin_unlock+0x1a/0x30
[ 3766.706253][   C28]  ? vfs_create_mount+0x371/0x4a0
[ 3766.711150][   C28]  path_mount+0xe6b/0x1720
do_new_mount_fc at fs/namespace.c:2839
(inlined by) do_new_mount at fs/namespace.c:2898
(inlined by) path_mount at fs/namespace.c:3227
[ 3766.715438][   C28]  ? finish_automount+0x750/0x750
[ 3766.720328][   C28]  ? getname_flags+0x88/0x3e0
[ 3766.724877][   C28]  do_mount+0xc6/0xe0
[ 3766.728726][   C28]  ? path_mount+0x1720/0x1720
[ 3766.733275][   C28]  ? _copy_from_user+0xab/0xf0
[ 3766.737906][   C28]  ? memdup_user+0x4f/0x80
[ 3766.742193][   C28]  __x64_sys_mount+0x15d/0x1b0
[ 3766.746828][   C28]  do_syscall_64+0x33/0x40
[ 3766.751111][   C28]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 3914.819439][   C36] watchdog: BUG: soft lockup - CPU#36 stuck for 22s! [systemd-journal:902]
[ 3914.827884][   C36] Modules linked in: acpi_cpufreq(+) ip_tables x_tables sd_mod ahci libahci tg3 bnxt_en megaraid_sas libata firmware_class libphy dm_mirror dm_region_hash dm_log dm_mod
[ 3914.844543][   C36] irq event stamp: 196688
[ 3914.848748][   C36] hardirqs last  enabled at (196687): [<ffffffff82800c42>] asm_sysvec_apic_timer_interrupt+0x12/0x20
[ 3914.859450][   C36] hardirqs last disabled at (196688): [<ffffffff8277e45a>] sysvec_apic_timer_interrupt+0xa/0xa0
[ 3914.869709][   C36] softirqs last  enabled at (196684): [<ffffffff82a0061b>] __do_softirq+0x61b/0x95d
[ 3914.878930][   C36] softirqs last disabled at (196679): [<ffffffff82800ec2>] asm_call_irq_on_stack+0x12/0x20
[ 3914.888759][   C36] CPU: 36 PID: 902 Comm: systemd-journal Tainted: G             L    5.10.0-rc2-next-20201109+ #2
[ 3914.899195][   C36] Hardware name: Dell Inc. PowerEdge R6415/07YXFK, BIOS 1.9.3 06/25/2019
[ 3914.907471][   C36] RIP: 0010:path_init+0x1f3/0x1380
[ 3914.912448][   C36] Code: 00 00 00 00 00 fc ff df 48 89 d1 48 c1 e9 03 48 01 c1 f3 90 0f b6 01 84 c0 74 08 3c 03 0f 8e 9a 0d 00 00 44 8b 3a 41 f6 c7 01 <75> e6 48 b8 00 00 00 00 00 fc ff df 48 8d 7b 44 48 89a
[ 3914.931901][   C36] RSP: 0018:ffffc900065dfc08 EFLAGS: 00000202
[ 3914.937837][   C36] RAX: 0000000000000000 RBX: ffffc900065dfd40 RCX: fffffbfff06426b0
[ 3914.945675][   C36] RDX: ffffffff83213580 RSI: 00000000d93ef353 RDI: ffffc900065dfd80
[ 3914.953514][   C36] RBP: ffffc900065dfc98 R08: fffffbfff164cb0d R09: fffffbfff164cb0d
[ 3914.961349][   C36] R10: 0000000000000246 R11: fffffbfff164cb0c R12: ffff8881159d5920
[ 3914.969186][   C36] R13: ffffc900065dfd78 R14: 0000000000000041 R15: 000000000000039d
[ 3914.977028][   C36] FS:  00007fc5f95f9980(0000) GS:ffff8881b7240000(0000) knlGS:0000000000000000
[ 3914.985814][   C36] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 3914.992262][   C36] CR2: 000055ea2994ba42 CR3: 000000013702a000 CR4: 00000000003506e0
[ 3915.000097][   C36] Call Trace:
[ 3915.003257][   C36]  path_lookupat.isra.61+0x20/0x440
[ 3915.008323][   C36]  ? find_held_lock+0x33/0x1c0
[ 3915.012954][   C36]  filename_lookup.part.73+0x15c/0x290
[ 3915.018283][   C36]  ? __might_fault+0xb5/0x160
[ 3915.022831][   C36]  ? do_symlinkat+0x190/0x190
[ 3915.027375][   C36]  ? strncpy_from_user+0x6b/0x330
[ 3915.032268][   C36]  ? getname_flags+0x88/0x3e0
[ 3915.036809][   C36]  ? kmem_cache_alloc+0x244/0x270
[ 3915.041701][   C36]  do_faccessat+0xc0/0x5a0
[ 3915.045987][   C36]  ? stream_open+0x60/0x60
[ 3915.050269][   C36]  do_syscall_64+0x33/0x40
[ 3915.054552][   C36]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 3915.060306][   C36] RIP: 0033:0x7fc5f862697b
[ 3915.064590][   C36] Code: 77 05 c3 0f 1f 40 00 48 8b 15 09 f5 2c 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff c3 0f 1f 40 00 f3 0f 1e fa b8 15 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 05 c3 0f 1f 40 00 48 8b 15 d9 f48
[ 3915.084044][   C36] RSP: 002b:00007ffdefba1198 EFLAGS: 00000246 ORIG_RAX: 0000000000000015
[ 3915.092322][   C36] RAX: ffffffffffffffda RBX: 00007ffdefba3cf0 RCX: 00007fc5f862697b
[ 3915.100163][   C36] RDX: 00007fc5f91032e8 RSI: 0000000000000000 RDI: 0000556a2401c0d0
[ 3915.107996][   C36] RBP: 00007ffdefba11e0 R08: 0000000000000000 R09: 0000000000000000
[ 3915.115832][   C36] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
[ 3915.123667][   C36] R13: 0000000000000000 R14: 0000000000000009 R15: 0000556a254de950
[ 3917.159439][    C0] watchdog: BUG: soft lockup - CPU#0 stuck for 23s! [systemd:1]
[ 3917.166926][    C0] Modules linked in: acpi_cpufreq(+) ip_tables x_tables sd_mod ahci libahci tg3 bnxt_en megaraid_sas libata firmware_class libphy dm_mirror dm_region_hash dm_log dm_mod
[ 3917.183572][    C0] irq event stamp: 94238206
[ 3917.187944][    C0] hardirqs last  enabled at (94238205): [<ffffffff82800b9e>] asm_common_interrupt+0x1e/0x40
[ 3917.197857][    C0] hardirqs last disabled at (94238206): [<ffffffff8277e45a>] sysvec_apic_timer_interrupt+0xa/0xa0
[ 3917.208289][    C0] softirqs last  enabled at (94219940): [<ffffffff82a0061b>] __do_softirq+0x61b/0x95d
[ 3917.217685][    C0] softirqs last disabled at (94219881): [<ffffffff82800ec2>] asm_call_irq_on_stack+0x12/0x20
[ 3917.227688][    C0] CPU: 0 PID: 1 Comm: systemd Tainted: G             L    5.10.0-rc2-next-20201109+ #2
[ 3917.237167][    C0] Hardware name: Dell Inc. PowerEdge R6415/07YXFK, BIOS 1.9.3 06/25/2019
[ 3917.245437][    C0] RIP: 0010:lock_acquire+0x21b/0x820
[ 3917.250585][    C0] Code: fc ff df 48 01 c3 c7 03 00 00 00 00 c7 43 08 00 00 00 00 48 8b 84 24 90 00 00 00 65 48 33 04 25 28 00 00 00 0f 85 1a 05 00 00 <48> 81 c4 98 00 00 00 5b 5d 41 5c 41 5d 41 5e 41 5f c3c
[ 3917.270033][    C0] RSP: 0018:ffffc9000006f9f8 EFLAGS: 00000246
[ 3917.275959][    C0] RAX: 0000000000000000 RBX: fffff5200000df42 RCX: 1ffff9200000df28
[ 3917.283795][    C0] RDX: 1ffff11020645769 RSI: 00000000ffffffff RDI: 0000000000000001
[ 3917.291627][    C0] RBP: 0000000000000001 R08: fffffbfff164cb10 R09: fffffbfff164cb10
[ 3917.299463][    C0] R10: 0000000000000246 R11: fffffbfff164cb0f R12: ffff88812be555b0
[ 3917.307297][    C0] R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
[ 3917.315133][    C0] FS:  00007f12bb8c59c0(0000) GS:ffff8881b7000000(0000) knlGS:0000000000000000
[ 3917.323921][    C0] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 3917.330368][    C0] CR2: 00007f0c2d828fd0 CR3: 000000011868a000 CR4: 00000000003506f0
[ 3917.338202][    C0] Call Trace:
[ 3917.341360][    C0]  ? rcu_read_unlock+0x40/0x40
[ 3917.345987][    C0]  __d_move+0x2a2/0x16f0
[ 3917.350096][    C0]  ? d_move+0x47/0x70
[ 3917.353944][    C0]  ? _raw_spin_unlock+0x1a/0x30
[ 3917.358656][    C0]  d_move+0x47/0x70
[ 3917.362330][    C0]  ? vfs_rename+0x9ac/0x1270
[ 3917.366786][    C0]  vfs_rename+0x9ac/0x1270
[ 3917.371068][    C0]  ? vfs_link+0x830/0x830
[ 3917.375261][    C0]  ? do_renameat2+0x58c/0x930
[ 3917.379804][    C0]  do_renameat2+0x58c/0x930
[ 3917.384173][    C0]  ? __ia32_sys_link+0x80/0x80
[ 3917.388800][    C0]  ? rcu_read_lock_bh_held+0xb0/0xb0
[ 3917.393948][    C0]  ? rcu_read_lock_sched_held+0x9c/0xd0
[ 3917.399354][    C0]  ? rcu_read_lock_bh_held+0xb0/0xb0
[ 3917.404503][    C0]  ? lockdep_hardirqs_on_prepare+0x27c/0x3d0
[ 3917.410346][    C0]  ? trace_hardirqs_on+0x1c/0x150
[ 3917.415234][    C0]  ? asm_common_interrupt+0x1e/0x40
[ 3917.420294][    C0]  ? strncpy_from_user+0x14c/0x330
[ 3917.425269][    C0]  ? strncpy_from_user+0x6b/0x330
[ 3917.430158][    C0]  ? getname_flags+0x88/0x3e0
[ 3917.434699][    C0]  __x64_sys_rename+0x75/0x90
[ 3917.439239][    C0]  do_syscall_64+0x33/0x40
[ 3917.443520][    C0]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 3917.449274][    C0] RIP: 0033:0x7f12b9b759eb
[ 3917.453557][    C0] Code: e8 5a 0a 08 00 85 c0 0f 95 c0 0f b6 c0 f7 d8 5b c3 66 0f 1f 44 00 00 b8 ff ff ff ff 5b c3 90 f3 0f 1e fa b8 52 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 05 c3 0f 1f 40 00 48 8b 15 69 e48
[ 3917.473003][    C0] RSP: 002b:00007fff76252538 EFLAGS: 00000246 ORIG_RAX: 0000000000000052
[ 3917.481272][    C0] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f12b9b759eb
[ 3917.489107][    C0] RDX: 000055ea2997f400 RSI: 00007fff76252570 RDI: 000055ea2997f450
[ 3917.496942][    C0] RBP: 00007fff76252570 R08: 0000000000000000 R09: 0000000065732e32
[ 3917.504776][    C0] R10: 0000000000000003 R11: 0000000000000246 R12: 000055ea2996fcf8
[ 3917.512610][    C0] R13: 000055ea2996fcf8 R14: 000055ea277097f0 R15: 0000000000000000


[ 3634.443982][   C37] NMI backtrace for cpu 37
[ 3634.443984][   C37] CPU: 37 PID: 906 Comm: udevadm Tainted: G             L    5.10.0-rc2-next-20201109+ #3
[ 3634.443986][   C37] Hardware name: Dell Inc. PowerEdge R6415/07YXFK, BIOS 1.9.3 06/25/2019
[ 3634.443987][   C37] RIP: 0010:io_serial_in+0x5c/0x90
[ 3634.443989][   C37] Code: 48 8d 7b 40 0f b6 8b f1 00 00 00 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 d3 e6 80 3c 02 00 75 1e 03 73 40 89 f2 ec <48> 83 c4 08 0f b6 c0 5b c3 89 74 24 04 e8 d2 90 81 ff4
[ 3634.443991][   C37] RSP: 0018:ffffc90004a38780 EFLAGS: 00000002
[ 3634.443993][   C37] RAX: dffffc0000000000 RBX: ffffffffa0b1c988 RCX: 0000000000000000
[ 3634.443995][   C37] RDX: 00000000000002fd RSI: 00000000000002fd RDI: ffffffffa0b1c9c8
[ 3634.443996][   C37] RBP: 0000000000000020 R08: 0000000000000004 R09: fffff520009470f3
[ 3634.443998][   C37] R10: 0000000000000003 R11: fffff520009470f3 R12: fffffbfff4163984
[ 3634.443999][   C37] R13: fffffbfff416393b R14: ffffffffa0b1c9d8 R15: ffffffffa0b1c988
[ 3634.444001][   C37] FS:  00007f6947084980(0000) GS:ffff88866e440000(0000) knlGS:0000000000000000
[ 3634.444002][   C37] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 3634.444004][   C37] CR2: 00007fd220b94816 CR3: 000000015371e000 CR4: 00000000003506e0
[ 3634.444005][   C37] Call Trace:
[ 3634.444006][   C37]  <IRQ>
[ 3634.444007][   C37]  wait_for_xmitr+0x7c/0x1b0
[ 3634.444008][   C37]  ? wait_for_xmitr+0x1b0/0x1b0
[ 3634.444010][   C37]  serial8250_console_putchar+0x11/0x50
[ 3634.444011][   C37]  uart_console_write+0x39/0xc0
[ 3634.444012][   C37]  serial8250_console_write+0x74c/0x8a0
[ 3634.444013][   C37]  ? serial8250_start_tx+0x810/0x810
[ 3634.444015][   C37]  ? rcu_read_unlock+0x40/0x40
[ 3634.444016][   C37]  ? do_raw_spin_lock+0x121/0x290
[ 3634.444017][   C37]  ? rwlock_bug.part.1+0x90/0x90
[ 3634.444018][   C37]  ? prb_read_valid+0x61/0x90
[ 3634.444020][   C37]  ? prb_final_commit+0x10/0x10
[ 3634.444021][   C37]  console_unlock+0x721/0xa20
[ 3634.444022][   C37]  ? do_syslog.part.22+0x5d0/0x5d0
[ 3634.444023][   C37]  ? lock_acquire+0x1c8/0x820
[ 3634.444024][   C37]  ? lock_downgrade+0x700/0x700
[ 3634.444026][   C37]  vprintk_emit+0x201/0x2c0
[ 3634.444027][   C37]  printk+0x9a/0xc0
[ 3634.444028][   C37]  ? record_print_text.cold.38+0x11/0x11
[ 3634.444029][   C37]  ? __module_text_address+0xe/0x140
[ 3634.444031][   C37]  ? nmi_cpu_backtrace.cold.10+0x18/0xc5
[ 3634.444032][   C37]  show_trace_log_lvl+0x228/0x2bb
[ 3634.444033][   C37]  ? nmi_cpu_backtrace.cold.10+0x18/0xc5
[ 3634.444035][   C37]  ? nmi_cpu_backtrace.cold.10+0x18/0xc5
[ 3634.444036][   C37]  ? lapic_can_unplug_cpu+0x11/0x70
[ 3634.444037][   C37]  dump_stack+0x99/0xcb
[ 3634.444038][   C37]  nmi_cpu_backtrace.cold.10+0x18/0xc5
[ 3634.444040][   C37]  ? lapic_can_unplug_cpu+0x70/0x70
[ 3634.444041][   C37]  nmi_trigger_cpumask_backtrace+0x232/0x2a0
[ 3634.444042][   C37]  rcu_dump_cpu_stacks+0x1ad/0x1f9
[ 3634.444043][   C37]  rcu_sched_clock_irq.cold.90+0x4f7/0x968
[ 3634.444045][   C37]  ? tick_sched_do_timer+0x140/0x140
[ 3634.444046][   C37]  update_process_times+0x75/0xb0
[ 3634.444047][   C37]  tick_sched_timer+0xc8/0xf0
[ 3634.444048][   C37]  __hrtimer_run_queues+0x529/0xbb0
[ 3634.444050][   C37]  ? enqueue_hrtimer+0x330/0x330
[ 3634.444051][   C37]  ? ktime_get_update_offsets_now+0xd6/0x2b0
[ 3634.444052][   C37]  hrtimer_interrupt+0x2c2/0x750
[ 3634.444054][   C37]  __sysvec_apic_timer_interrupt+0x13c/0x520
[ 3634.444055][   C37]  asm_call_irq_on_stack+0x12/0x20
[ 3634.444056][   C37]  </IRQ>
[ 3634.444057][   C37]  sysvec_apic_timer_interrupt+0x85/0xa0
[ 3634.444059][   C37]  asm_sysvec_apic_timer_interrupt+0x12/0x20


_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

Re: [PATCH v3 19/35] x86/io_apic: Cleanup trigger/polarity helpers

[David Woodhouse]

[-- Attachment #1.1: Type: text/plain, Size: 2135 bytes --]

On Tue, 2020-11-10 at 01:31 -0500, Qian Cai wrote:
> On Sat, 2020-10-24 at 22:35 +0100, David Woodhouse wrote:
> > From: Thomas Gleixner <tglx@linutronix.de>
> > 
> > 'trigger' and 'polarity' are used throughout the I/O-APIC code for handling
> > the trigger type (edge/level) and the active low/high configuration. While
> > there are defines for initializing these variables and struct members, they
> > are not used consequently and the meaning of 'trigger' and 'polarity' is
> > opaque and confusing at best.
> > 
> > Rename them to 'is_level' and 'active_low' and make them boolean in various
> > structs so it's entirely clear what the meaning is.
> > 
> > Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
> > Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
> > ---
> >   arch/x86/include/asm/hw_irq.h       |   6 +-
> >   arch/x86/kernel/apic/io_apic.c      | 244 +++++++++++++---------------
> >   arch/x86/pci/intel_mid_pci.c        |   8 +-
> >   drivers/iommu/amd/iommu.c           |  10 +-
> >   drivers/iommu/intel/irq_remapping.c |   9 +-
> >   5 files changed, 130 insertions(+), 147 deletions(-)
> 
> Reverting the rest of patchset up to this commit on next-20201109 fixed an
> endless soft-lockups issue booting an AMD server below. I noticed that the
> failed boots always has this IOMMU IO_PAGE_FAULT before those soft-lockups:

Hm, attempting to reproduce this shows something else. Ever since
commit be62dbf554c5 ("iommu/amd: Convert AMD iommu driver to the dma-
iommu api") in 5.5 the following stops working for me:

$ qemu-system-x86_64 -serial mon:stdio -kernel bzImage  -machine q35,accel=kvm,kernel-irqchip=split -m 2G -device amd-iommu,intremap=off -append "console=ttyS0 apic=verbose debug" -display none

It hasn't got a hard drive but I can watch the SATA interrupts fail as
it probes the CD-ROM:

[    7.403327] ata3.00: qc timeout (cmd 0xa1)
[    7.405980] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)

Adding 'iommu=off' to the kernel command line makes it work again, in
that it correctly panics at the lack of a root file system, quickly.



[-- Attachment #1.2: smime.p7s --]
[-- Type: application/x-pkcs7-signature, Size: 5174 bytes --]

[-- Attachment #2: Type: text/plain, Size: 156 bytes --]

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

Re: [PATCH v3 19/35] x86/io_apic: Cleanup trigger/polarity helpers

[Paolo Bonzini]

On 10/11/20 09:59, David Woodhouse wrote:
> Hm, attempting to reproduce this shows something else. Ever since
> commit be62dbf554c5 ("iommu/amd: Convert AMD iommu driver to the dma-
> iommu api") in 5.5 the following stops working for me:
> 
> $ qemu-system-x86_64 -serial mon:stdio -kernel bzImage  -machine q35,accel=kvm,kernel-irqchip=split -m 2G -device amd-iommu,intremap=off -append "console=ttyS0 apic=verbose debug" -display none
> 
> It hasn't got a hard drive but I can watch the SATA interrupts fail as
> it probes the CD-ROM:
> 
> [    7.403327] ata3.00: qc timeout (cmd 0xa1)
> [    7.405980] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
> 
> Adding 'iommu=off' to the kernel command line makes it work again, in
> that it correctly panics at the lack of a root file system, quickly.

That might well be a QEMU bug though, AMD emulation is kinda experimental.

Paolo
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 20/35] x86/ioapic: Cleanup IO/APIC route entry structs

[David Woodhouse]

From: Thomas Gleixner <tglx@linutronix.de>

Having two seperate structs for the I/O-APIC RTE entries (non-remapped and
DMAR remapped) requires type casts and makes it hard to map.

Combine them in IO_APIC_routing_entry by defining a union of two 64bit
bitfields. Use naming which reflects which bits are shared and which bits
are actually different for the operating modes.

[dwmw2: Fix it up and finish the job, pulling the 32-bit w1,w2 words for
        register access into the same union and eliminating a few more
        places where bits were accessed through masks and shifts.]

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
---
 arch/x86/include/asm/io_apic.h      |  78 ++++++---------
 arch/x86/kernel/apic/io_apic.c      | 144 +++++++++++++---------------
 drivers/iommu/amd/iommu.c           |   8 +-
 drivers/iommu/hyperv-iommu.c        |   4 +-
 drivers/iommu/intel/irq_remapping.c |  19 ++--
 5 files changed, 108 insertions(+), 145 deletions(-)

diff --git a/arch/x86/include/asm/io_apic.h b/arch/x86/include/asm/io_apic.h
index a1a26f6d3aa4..73da644b2f0d 100644
--- a/arch/x86/include/asm/io_apic.h
+++ b/arch/x86/include/asm/io_apic.h
@@ -13,15 +13,6 @@
  * Copyright (C) 1997, 1998, 1999, 2000 Ingo Molnar
  */
 
-/* I/O Unit Redirection Table */
-#define IO_APIC_REDIR_VECTOR_MASK	0x000FF
-#define IO_APIC_REDIR_DEST_LOGICAL	0x00800
-#define IO_APIC_REDIR_DEST_PHYSICAL	0x00000
-#define IO_APIC_REDIR_SEND_PENDING	(1 << 12)
-#define IO_APIC_REDIR_REMOTE_IRR	(1 << 14)
-#define IO_APIC_REDIR_LEVEL_TRIGGER	(1 << 15)
-#define IO_APIC_REDIR_MASKED		(1 << 16)
-
 /*
  * The structure of the IO-APIC:
  */
@@ -65,52 +56,39 @@ union IO_APIC_reg_03 {
 };
 
 struct IO_APIC_route_entry {
-	__u32	vector		:  8,
-		delivery_mode	:  3,	/* 000: FIXED
-					 * 001: lowest prio
-					 * 111: ExtINT
-					 */
-		dest_mode	:  1,	/* 0: physical, 1: logical */
-		delivery_status	:  1,
-		polarity	:  1,
-		irr		:  1,
-		trigger		:  1,	/* 0: edge, 1: level */
-		mask		:  1,	/* 0: enabled, 1: disabled */
-		__reserved_2	: 15;
-
-	__u32	__reserved_3	: 24,
-		dest		:  8;
-} __attribute__ ((packed));
-
-struct IR_IO_APIC_route_entry {
-	__u64	vector		: 8,
-		zero		: 3,
-		index2		: 1,
-		delivery_status : 1,
-		polarity	: 1,
-		irr		: 1,
-		trigger		: 1,
-		mask		: 1,
-		reserved	: 31,
-		format		: 1,
-		index		: 15;
+	union {
+		struct {
+			u64	vector			:  8,
+				delivery_mode		:  3,
+				dest_mode_logical	:  1,
+				delivery_status		:  1,
+				active_low		:  1,
+				irr			:  1,
+				is_level		:  1,
+				masked			:  1,
+				reserved_0		: 15,
+				reserved_1		: 24,
+				destid_0_7		:  8;
+		};
+		struct {
+			u64	ir_shared_0		:  8,
+				ir_zero			:  3,
+				ir_index_15		:  1,
+				ir_shared_1		:  5,
+				ir_reserved_0		: 31,
+				ir_format		:  1,
+				ir_index_0_14		: 15;
+		};
+		struct {
+			u64	w1			: 32,
+				w2			: 32;
+		};
+	};
 } __attribute__ ((packed));
 
 struct irq_alloc_info;
 struct ioapic_domain_cfg;
 
-#define IOAPIC_EDGE			0
-#define IOAPIC_LEVEL			1
-
-#define IOAPIC_MASKED			1
-#define IOAPIC_UNMASKED			0
-
-#define IOAPIC_POL_HIGH			0
-#define IOAPIC_POL_LOW			1
-
-#define IOAPIC_DEST_MODE_PHYSICAL	0
-#define IOAPIC_DEST_MODE_LOGICAL	1
-
 #define	IOAPIC_MAP_ALLOC		0x1
 #define	IOAPIC_MAP_CHECK		0x2
 
diff --git a/arch/x86/kernel/apic/io_apic.c b/arch/x86/kernel/apic/io_apic.c
index 24a7bba7cbf4..07e754131854 100644
--- a/arch/x86/kernel/apic/io_apic.c
+++ b/arch/x86/kernel/apic/io_apic.c
@@ -286,31 +286,26 @@ static void io_apic_write(unsigned int apic, unsigned int reg,
 	writel(value, &io_apic->data);
 }
 
-union entry_union {
-	struct { u32 w1, w2; };
-	struct IO_APIC_route_entry entry;
-};
-
 static struct IO_APIC_route_entry __ioapic_read_entry(int apic, int pin)
 {
-	union entry_union eu;
+	struct IO_APIC_route_entry entry;
 
-	eu.w1 = io_apic_read(apic, 0x10 + 2 * pin);
-	eu.w2 = io_apic_read(apic, 0x11 + 2 * pin);
+	entry.w1 = io_apic_read(apic, 0x10 + 2 * pin);
+	entry.w2 = io_apic_read(apic, 0x11 + 2 * pin);
 
-	return eu.entry;
+	return entry;
 }
 
 static struct IO_APIC_route_entry ioapic_read_entry(int apic, int pin)
 {
-	union entry_union eu;
+	struct IO_APIC_route_entry entry;
 	unsigned long flags;
 
 	raw_spin_lock_irqsave(&ioapic_lock, flags);
-	eu.entry = __ioapic_read_entry(apic, pin);
+	entry = __ioapic_read_entry(apic, pin);
 	raw_spin_unlock_irqrestore(&ioapic_lock, flags);
 
-	return eu.entry;
+	return entry;
 }
 
 /*
@@ -321,11 +316,8 @@ static struct IO_APIC_route_entry ioapic_read_entry(int apic, int pin)
  */
 static void __ioapic_write_entry(int apic, int pin, struct IO_APIC_route_entry e)
 {
-	union entry_union eu = {{0, 0}};
-
-	eu.entry = e;
-	io_apic_write(apic, 0x11 + 2*pin, eu.w2);
-	io_apic_write(apic, 0x10 + 2*pin, eu.w1);
+	io_apic_write(apic, 0x11 + 2*pin, e.w2);
+	io_apic_write(apic, 0x10 + 2*pin, e.w1);
 }
 
 static void ioapic_write_entry(int apic, int pin, struct IO_APIC_route_entry e)
@@ -344,12 +336,12 @@ static void ioapic_write_entry(int apic, int pin, struct IO_APIC_route_entry e)
  */
 static void ioapic_mask_entry(int apic, int pin)
 {
+	struct IO_APIC_route_entry e = { .masked = true };
 	unsigned long flags;
-	union entry_union eu = { .entry.mask = IOAPIC_MASKED };
 
 	raw_spin_lock_irqsave(&ioapic_lock, flags);
-	io_apic_write(apic, 0x10 + 2*pin, eu.w1);
-	io_apic_write(apic, 0x11 + 2*pin, eu.w2);
+	io_apic_write(apic, 0x10 + 2*pin, e.w1);
+	io_apic_write(apic, 0x11 + 2*pin, e.w2);
 	raw_spin_unlock_irqrestore(&ioapic_lock, flags);
 }
 
@@ -422,20 +414,15 @@ static void __init replace_pin_at_irq_node(struct mp_chip_data *data, int node,
 	add_pin_to_irq_node(data, node, newapic, newpin);
 }
 
-static void io_apic_modify_irq(struct mp_chip_data *data,
-			       int mask_and, int mask_or,
+static void io_apic_modify_irq(struct mp_chip_data *data, bool masked,
 			       void (*final)(struct irq_pin_list *entry))
 {
-	union entry_union eu;
 	struct irq_pin_list *entry;
 
-	eu.entry = data->entry;
-	eu.w1 &= mask_and;
-	eu.w1 |= mask_or;
-	data->entry = eu.entry;
+	data->entry.masked = masked;
 
 	for_each_irq_pin(entry, data->irq_2_pin) {
-		io_apic_write(entry->apic, 0x10 + 2 * entry->pin, eu.w1);
+		io_apic_write(entry->apic, 0x10 + 2 * entry->pin, data->entry.w1);
 		if (final)
 			final(entry);
 	}
@@ -459,13 +446,13 @@ static void mask_ioapic_irq(struct irq_data *irq_data)
 	unsigned long flags;
 
 	raw_spin_lock_irqsave(&ioapic_lock, flags);
-	io_apic_modify_irq(data, ~0, IO_APIC_REDIR_MASKED, &io_apic_sync);
+	io_apic_modify_irq(data, true, &io_apic_sync);
 	raw_spin_unlock_irqrestore(&ioapic_lock, flags);
 }
 
 static void __unmask_ioapic(struct mp_chip_data *data)
 {
-	io_apic_modify_irq(data, ~IO_APIC_REDIR_MASKED, 0, NULL);
+	io_apic_modify_irq(data, false, NULL);
 }
 
 static void unmask_ioapic_irq(struct irq_data *irq_data)
@@ -506,8 +493,8 @@ static void __eoi_ioapic_pin(int apic, int pin, int vector)
 		/*
 		 * Mask the entry and change the trigger mode to edge.
 		 */
-		entry1.mask = IOAPIC_MASKED;
-		entry1.trigger = IOAPIC_EDGE;
+		entry1.masked = true;
+		entry1.is_level = false;
 
 		__ioapic_write_entry(apic, pin, entry1);
 
@@ -542,8 +529,8 @@ static void clear_IO_APIC_pin(unsigned int apic, unsigned int pin)
 	 * Make sure the entry is masked and re-read the contents to check
 	 * if it is a level triggered pin and if the remote-IRR is set.
 	 */
-	if (entry.mask == IOAPIC_UNMASKED) {
-		entry.mask = IOAPIC_MASKED;
+	if (!entry.masked) {
+		entry.masked = true;
 		ioapic_write_entry(apic, pin, entry);
 		entry = ioapic_read_entry(apic, pin);
 	}
@@ -556,8 +543,8 @@ static void clear_IO_APIC_pin(unsigned int apic, unsigned int pin)
 		 * doesn't clear the remote-IRR if the trigger mode is not
 		 * set to level.
 		 */
-		if (entry.trigger == IOAPIC_EDGE) {
-			entry.trigger = IOAPIC_LEVEL;
+		if (!entry.is_level) {
+			entry.is_level = true;
 			ioapic_write_entry(apic, pin, entry);
 		}
 		raw_spin_lock_irqsave(&ioapic_lock, flags);
@@ -659,8 +646,8 @@ void mask_ioapic_entries(void)
 			struct IO_APIC_route_entry entry;
 
 			entry = ioapics[apic].saved_registers[pin];
-			if (entry.mask == IOAPIC_UNMASKED) {
-				entry.mask = IOAPIC_MASKED;
+			if (!entry.masked) {
+				entry.masked = true;
 				ioapic_write_entry(apic, pin, entry);
 			}
 		}
@@ -947,8 +934,8 @@ static bool mp_check_pin_attr(int irq, struct irq_alloc_info *info)
 	if (irq < nr_legacy_irqs() && data->count == 1) {
 		if (info->ioapic.is_level != data->is_level)
 			mp_register_handler(irq, info->ioapic.is_level);
-		data->entry.trigger = data->is_level = info->ioapic.is_level;
-		data->entry.polarity = data->active_low = info->ioapic.active_low;
+		data->entry.is_level = data->is_level = info->ioapic.is_level;
+		data->entry.active_low = data->active_low = info->ioapic.active_low;
 	}
 
 	return data->is_level == info->ioapic.is_level &&
@@ -1231,10 +1218,9 @@ void ioapic_zap_locks(void)
 
 static void io_apic_print_entries(unsigned int apic, unsigned int nr_entries)
 {
-	int i;
-	char buf[256];
 	struct IO_APIC_route_entry entry;
-	struct IR_IO_APIC_route_entry *ir_entry = (void *)&entry;
+	char buf[256];
+	int i;
 
 	printk(KERN_DEBUG "IOAPIC %d:\n", apic);
 	for (i = 0; i <= nr_entries; i++) {
@@ -1242,20 +1228,20 @@ static void io_apic_print_entries(unsigned int apic, unsigned int nr_entries)
 		snprintf(buf, sizeof(buf),
 			 " pin%02x, %s, %s, %s, V(%02X), IRR(%1d), S(%1d)",
 			 i,
-			 entry.mask == IOAPIC_MASKED ? "disabled" : "enabled ",
-			 entry.trigger == IOAPIC_LEVEL ? "level" : "edge ",
-			 entry.polarity == IOAPIC_POL_LOW ? "low " : "high",
+			 entry.masked ? "disabled" : "enabled ",
+			 entry.is_level ? "level" : "edge ",
+			 entry.active_low ? "low " : "high",
 			 entry.vector, entry.irr, entry.delivery_status);
-		if (ir_entry->format)
+		if (entry.ir_format) {
 			printk(KERN_DEBUG "%s, remapped, I(%04X),  Z(%X)\n",
-			       buf, (ir_entry->index2 << 15) | ir_entry->index,
-			       ir_entry->zero);
-		else
-			printk(KERN_DEBUG "%s, %s, D(%02X), M(%1d)\n",
 			       buf,
-			       entry.dest_mode == IOAPIC_DEST_MODE_LOGICAL ?
-			       "logical " : "physical",
-			       entry.dest, entry.delivery_mode);
+			       (entry.ir_index_15 << 15) | entry.ir_index_0_14,
+				entry.ir_zero);
+		} else {
+			printk(KERN_DEBUG "%s, %s, D(%02X), M(%1d)\n", buf,
+			       entry.dest_mode_logical ? "logical " : "physical",
+			       entry.destid_0_7, entry.delivery_mode);
+		}
 	}
 }
 
@@ -1380,8 +1366,8 @@ void __init enable_IO_APIC(void)
 		/* If the interrupt line is enabled and in ExtInt mode
 		 * I have found the pin where the i8259 is connected.
 		 */
-		if ((entry.mask == 0) &&
-		    (entry.delivery_mode == APIC_DELIVERY_MODE_EXTINT)) {
+		if (!entry.masked &&
+		    entry.delivery_mode == APIC_DELIVERY_MODE_EXTINT) {
 			ioapic_i8259.apic = apic;
 			ioapic_i8259.pin  = pin;
 			goto found_i8259;
@@ -1425,12 +1411,12 @@ void native_restore_boot_irq_mode(void)
 		struct IO_APIC_route_entry entry;
 
 		memset(&entry, 0, sizeof(entry));
-		entry.mask		= IOAPIC_UNMASKED;
-		entry.trigger		= IOAPIC_EDGE;
-		entry.polarity		= IOAPIC_POL_HIGH;
-		entry.dest_mode		= IOAPIC_DEST_MODE_PHYSICAL;
+		entry.masked		= false;
+		entry.is_level		= false;
+		entry.active_low	= false;
+		entry.dest_mode_logical	= false;
 		entry.delivery_mode	= APIC_DELIVERY_MODE_EXTINT;
-		entry.dest		= read_apic_id();
+		entry.destid_0_7	= read_apic_id();
 
 		/*
 		 * Add it to the IO-APIC irq-routing table:
@@ -1709,13 +1695,13 @@ static bool io_apic_level_ack_pending(struct mp_chip_data *data)
 
 	raw_spin_lock_irqsave(&ioapic_lock, flags);
 	for_each_irq_pin(entry, data->irq_2_pin) {
-		unsigned int reg;
+		struct IO_APIC_route_entry e;
 		int pin;
 
 		pin = entry->pin;
-		reg = io_apic_read(entry->apic, 0x10 + pin*2);
+		e.w1 = io_apic_read(entry->apic, 0x10 + pin*2);
 		/* Is the remote IRR bit set? */
-		if (reg & IO_APIC_REDIR_REMOTE_IRR) {
+		if (e.irr) {
 			raw_spin_unlock_irqrestore(&ioapic_lock, flags);
 			return true;
 		}
@@ -1874,7 +1860,7 @@ static void ioapic_configure_entry(struct irq_data *irqd)
 	 * ioapic chip to verify that.
 	 */
 	if (irqd->chip == &ioapic_chip) {
-		mpd->entry.dest = cfg->dest_apicid;
+		mpd->entry.destid_0_7 = cfg->dest_apicid;
 		mpd->entry.vector = cfg->vector;
 	}
 	for_each_irq_pin(entry, mpd->irq_2_pin)
@@ -1932,7 +1918,7 @@ static int ioapic_irq_get_chip_state(struct irq_data *irqd,
 		 * irrelevant because the IO-APIC treats them as fire and
 		 * forget.
 		 */
-		if (rentry.irr && rentry.trigger) {
+		if (rentry.irr && rentry.is_level) {
 			*state = true;
 			break;
 		}
@@ -2057,12 +2043,12 @@ static inline void __init unlock_ExtINT_logic(void)
 
 	memset(&entry1, 0, sizeof(entry1));
 
-	entry1.dest_mode = IOAPIC_DEST_MODE_PHYSICAL;
-	entry1.mask = IOAPIC_UNMASKED;
-	entry1.dest = hard_smp_processor_id();
-	entry1.delivery_mode = APIC_DELIVERY_MODE_EXTINT;
-	entry1.polarity = entry0.polarity;
-	entry1.trigger = IOAPIC_EDGE;
+	entry1.dest_mode_logical	= true;
+	entry1.masked			= false;
+	entry1.destid_0_7		= hard_smp_processor_id();
+	entry1.delivery_mode		= APIC_DELIVERY_MODE_EXTINT;
+	entry1.active_low		= entry0.active_low;
+	entry1.is_level			= false;
 	entry1.vector = 0;
 
 	ioapic_write_entry(apic, pin, entry1);
@@ -2937,17 +2923,17 @@ static void mp_setup_entry(struct irq_cfg *cfg, struct mp_chip_data *data,
 			   struct IO_APIC_route_entry *entry)
 {
 	memset(entry, 0, sizeof(*entry));
-	entry->delivery_mode = apic->delivery_mode;
-	entry->dest_mode     = apic->dest_mode_logical;
-	entry->dest	     = cfg->dest_apicid;
-	entry->vector	     = cfg->vector;
-	entry->trigger	     = data->is_level;
-	entry->polarity	     = data->active_low;
+	entry->delivery_mode	 = apic->delivery_mode;
+	entry->dest_mode_logical = apic->dest_mode_logical;
+	entry->destid_0_7	 = cfg->dest_apicid;
+	entry->vector		 = cfg->vector;
+	entry->is_level		 = data->is_level;
+	entry->active_low	 = data->active_low;
 	/*
 	 * Mask level triggered irqs. Edge triggered irqs are masked
 	 * by the irq core code in case they fire.
 	 */
-	entry->mask = data->is_level;
+	entry->masked		= data->is_level;
 }
 
 int mp_irqdomain_alloc(struct irq_domain *domain, unsigned int virq,
diff --git a/drivers/iommu/amd/iommu.c b/drivers/iommu/amd/iommu.c
index b0e5210e53b2..3d72ec7bbbf8 100644
--- a/drivers/iommu/amd/iommu.c
+++ b/drivers/iommu/amd/iommu.c
@@ -3687,11 +3687,11 @@ static void irq_remapping_prepare_irte(struct amd_ir_data *data,
 		entry = info->ioapic.entry;
 		info->ioapic.entry = NULL;
 		memset(entry, 0, sizeof(*entry));
-		entry->vector	= index;
-		entry->trigger	= info->ioapic.is_level;
-		entry->polarity	= info->ioapic.active_low;
+		entry->vector		= index;
+		entry->is_level		= info->ioapic.is_level;
+		entry->active_low	= info->ioapic.active_low;
 		/* Mask level triggered irqs. */
-		entry->mask	= info->ioapic.is_level;
+		entry->masked		= info->ioapic.is_level;
 		break;
 
 	case X86_IRQ_ALLOC_TYPE_HPET:
diff --git a/drivers/iommu/hyperv-iommu.c b/drivers/iommu/hyperv-iommu.c
index e09e2d734c57..1ab7eb918a5c 100644
--- a/drivers/iommu/hyperv-iommu.c
+++ b/drivers/iommu/hyperv-iommu.c
@@ -52,7 +52,7 @@ static int hyperv_ir_set_affinity(struct irq_data *data,
 		return ret;
 
 	entry = data->chip_data;
-	entry->dest = cfg->dest_apicid;
+	entry->destid_0_7 = cfg->dest_apicid;
 	entry->vector = cfg->vector;
 	send_cleanup_vector(cfg);
 
@@ -125,7 +125,7 @@ static int hyperv_irq_remapping_activate(struct irq_domain *domain,
 	struct irq_cfg *cfg = irqd_cfg(irq_data);
 	struct IO_APIC_route_entry *entry = irq_data->chip_data;
 
-	entry->dest = cfg->dest_apicid;
+	entry->destid_0_7 = cfg->dest_apicid;
 	entry->vector = cfg->vector;
 
 	return 0;
diff --git a/drivers/iommu/intel/irq_remapping.c b/drivers/iommu/intel/irq_remapping.c
index 54ca69333445..625bdb9f1627 100644
--- a/drivers/iommu/intel/irq_remapping.c
+++ b/drivers/iommu/intel/irq_remapping.c
@@ -1279,8 +1279,8 @@ static void intel_irq_remapping_prepare_irte(struct intel_ir_data *data,
 					     struct irq_alloc_info *info,
 					     int index, int sub_handle)
 {
-	struct IR_IO_APIC_route_entry *entry;
 	struct irte *irte = &data->irte_entry;
+	struct IO_APIC_route_entry *entry;
 
 	prepare_irte(irte, irq_cfg->vector, irq_cfg->dest_apicid);
 	switch (info->type) {
@@ -1294,22 +1294,21 @@ static void intel_irq_remapping_prepare_irte(struct intel_ir_data *data,
 			irte->avail, irte->vector, irte->dest_id,
 			irte->sid, irte->sq, irte->svt);
 
-		entry = (struct IR_IO_APIC_route_entry *)info->ioapic.entry;
+		entry = info->ioapic.entry;
 		info->ioapic.entry = NULL;
 		memset(entry, 0, sizeof(*entry));
-		entry->index2	= (index >> 15) & 0x1;
-		entry->zero	= 0;
-		entry->format	= 1;
-		entry->index	= (index & 0x7fff);
+		entry->ir_index_15	= !!(index & 0x8000);
+		entry->ir_format	= true;
+		entry->ir_index_0_14	= index & 0x7fff;
 		/*
 		 * IO-APIC RTE will be configured with virtual vector.
 		 * irq handler will do the explicit EOI to the io-apic.
 		 */
-		entry->vector	= info->ioapic.pin;
-		entry->trigger	= info->ioapic.is_level;
-		entry->polarity	= info->ioapic.active_low;
+		entry->vector		= info->ioapic.pin;
+		entry->is_level		= info->ioapic.is_level;
+		entry->active_low	= info->ioapic.active_low;
 		/* Mask level triggered irqs. */
-		entry->mask	= info->ioapic.is_level;
+		entry->masked		= info->ioapic.is_level;
 		break;
 
 	case X86_IRQ_ALLOC_TYPE_HPET:
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 21/35] x86/ioapic: Generate RTE directly from parent irqchip's MSI message

[David Woodhouse]

From: David Woodhouse <dwmw@amazon.co.uk>

The I/O-APIC generates an MSI cycle with address/data bits taken from its
Redirection Table Entry in some combination which used to make sense, but
now is just a bunch of bits which get passed through in some seemingly
arbitrary order.

Instead of making IRQ remapping drivers directly frob the I/OA-PIC RTE, let
them just do their job and generate an MSI message. The bit swizzling to
turn that MSI message into the I/O-APIC's RTE is the same in all cases,
since it's a function of the I/O-APIC hardware. The IRQ remappers have no
real need to get involved with that.

The only slight caveat is that the I/OAPIC is interpreting some of those
fields too, and it does want the 'vector' field to be unique to make EOI
work. The AMD IOMMU happens to put its IRTE index in the bits that the
I/O-APIC thinks are the vector field, and accommodates this requirement by
reserving the first 32 indices for the I/O-APIC.  The Intel IOMMU doesn't
actually use the bits that the I/O-APIC thinks are the vector field, so it
fills in the 'pin' value there instead.

[ tglx: Replaced the unreadably macro maze with the cleaned up RTE/msi_msg
  	bitfields and added commentry to explain the mapping magic ]

Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
---
 arch/x86/include/asm/hw_irq.h       |  11 ++-
 arch/x86/kernel/apic/io_apic.c      | 103 +++++++++++++++++++---------
 drivers/iommu/amd/iommu.c           |  12 ----
 drivers/iommu/hyperv-iommu.c        |  31 ---------
 drivers/iommu/intel/irq_remapping.c |  31 ++-------
 5 files changed, 83 insertions(+), 105 deletions(-)

diff --git a/arch/x86/include/asm/hw_irq.h b/arch/x86/include/asm/hw_irq.h
index 517847a94dbe..83a69f62637e 100644
--- a/arch/x86/include/asm/hw_irq.h
+++ b/arch/x86/include/asm/hw_irq.h
@@ -45,12 +45,11 @@ enum irq_alloc_type {
 };
 
 struct ioapic_alloc_info {
-	int				pin;
-	int				node;
-	u32				is_level	: 1;
-	u32				active_low	: 1;
-	u32				valid		: 1;
-	struct IO_APIC_route_entry	*entry;
+	int		pin;
+	int		node;
+	u32		is_level	: 1;
+	u32		active_low	: 1;
+	u32		valid		: 1;
 };
 
 struct uv_alloc_info {
diff --git a/arch/x86/kernel/apic/io_apic.c b/arch/x86/kernel/apic/io_apic.c
index 07e754131854..ea983da1a57f 100644
--- a/arch/x86/kernel/apic/io_apic.c
+++ b/arch/x86/kernel/apic/io_apic.c
@@ -48,6 +48,7 @@
 #include <linux/jiffies.h>	/* time_after() */
 #include <linux/slab.h>
 #include <linux/memblock.h>
+#include <linux/msi.h>
 
 #include <asm/irqdomain.h>
 #include <asm/io.h>
@@ -63,7 +64,6 @@
 #include <asm/setup.h>
 #include <asm/irq_remapping.h>
 #include <asm/hw_irq.h>
-
 #include <asm/apic.h>
 
 #define	for_each_ioapic(idx)		\
@@ -1848,21 +1848,58 @@ static void ioapic_ir_ack_level(struct irq_data *irq_data)
 	eoi_ioapic_pin(data->entry.vector, data);
 }
 
+/*
+ * The I/OAPIC is just a device for generating MSI messages from legacy
+ * interrupt pins. Various fields of the RTE translate into bits of the
+ * resulting MSI which had a historical meaning.
+ *
+ * With interrupt remapping, many of those bits have different meanings
+ * in the underlying MSI, but the way that the I/OAPIC transforms them
+ * from its RTE to the MSI message is the same. This function allows
+ * the parent IRQ domain to compose the MSI message, then takes the
+ * relevant bits to put them in the appropriate places in the RTE in
+ * order to generate that message when the IRQ happens.
+ *
+ * The setup here relies on a preconfigured route entry (is_level,
+ * active_low, masked) because the parent domain is merely composing the
+ * generic message routing information which is used for the MSI.
+ */
+static void ioapic_setup_msg_from_msi(struct irq_data *irq_data,
+				      struct IO_APIC_route_entry *entry)
+{
+	struct msi_msg msg;
+
+	/* Let the parent domain compose the MSI message */
+	irq_chip_compose_msi_msg(irq_data, &msg);
+
+	/*
+	 * - Real vector
+	 * - DMAR/IR: 8bit subhandle (ioapic.pin)
+	 * - AMD/IR:  8bit IRTE index
+	 */
+	entry->vector			= msg.arch_data.vector;
+	/* Delivery mode (for DMAR/IR all 0) */
+	entry->delivery_mode		= msg.arch_data.delivery_mode;
+	/* Destination mode or DMAR/IR index bit 15 */
+	entry->dest_mode_logical	= msg.arch_addr_lo.dest_mode_logical;
+	/* DMAR/IR: 1, 0 for all other modes */
+	entry->ir_format		= msg.arch_addr_lo.dmar_format;
+	/*
+	 * DMAR/IR: index bit 0-14.
+	 *
+	 * All other modes have bit 0-6 of dmar_index_0_14 cleared and the
+	 * topmost 8 bits are destination id bit 0-7 (entry::destid_0_7).
+	 */
+	entry->ir_index_0_14		= msg.arch_addr_lo.dmar_index_0_14;
+}
+
 static void ioapic_configure_entry(struct irq_data *irqd)
 {
 	struct mp_chip_data *mpd = irqd->chip_data;
-	struct irq_cfg *cfg = irqd_cfg(irqd);
 	struct irq_pin_list *entry;
 
-	/*
-	 * Only update when the parent is the vector domain, don't touch it
-	 * if the parent is the remapping domain. Check the installed
-	 * ioapic chip to verify that.
-	 */
-	if (irqd->chip == &ioapic_chip) {
-		mpd->entry.destid_0_7 = cfg->dest_apicid;
-		mpd->entry.vector = cfg->vector;
-	}
+	ioapic_setup_msg_from_msi(irqd, &mpd->entry);
+
 	for_each_irq_pin(entry, mpd->irq_2_pin)
 		__ioapic_write_entry(entry->apic, entry->pin, mpd->entry);
 }
@@ -2919,14 +2956,23 @@ static void mp_irqdomain_get_attr(u32 gsi, struct mp_chip_data *data,
 	}
 }
 
-static void mp_setup_entry(struct irq_cfg *cfg, struct mp_chip_data *data,
-			   struct IO_APIC_route_entry *entry)
+/*
+ * Configure the I/O-APIC specific fields in the routing entry.
+ *
+ * This is important to setup the I/O-APIC specific bits (is_level,
+ * active_low, masked) because the underlying parent domain will only
+ * provide the routing information and is oblivious of the I/O-APIC
+ * specific bits.
+ *
+ * The entry is just preconfigured at this point and not written into the
+ * RTE. This happens later during activation which will fill in the actual
+ * routing information.
+ */
+static void mp_preconfigure_entry(struct mp_chip_data *data)
 {
+	struct IO_APIC_route_entry *entry = &data->entry;
+
 	memset(entry, 0, sizeof(*entry));
-	entry->delivery_mode	 = apic->delivery_mode;
-	entry->dest_mode_logical = apic->dest_mode_logical;
-	entry->destid_0_7	 = cfg->dest_apicid;
-	entry->vector		 = cfg->vector;
 	entry->is_level		 = data->is_level;
 	entry->active_low	 = data->active_low;
 	/*
@@ -2939,11 +2985,10 @@ static void mp_setup_entry(struct irq_cfg *cfg, struct mp_chip_data *data,
 int mp_irqdomain_alloc(struct irq_domain *domain, unsigned int virq,
 		       unsigned int nr_irqs, void *arg)
 {
-	int ret, ioapic, pin;
-	struct irq_cfg *cfg;
-	struct irq_data *irq_data;
-	struct mp_chip_data *data;
 	struct irq_alloc_info *info = arg;
+	struct mp_chip_data *data;
+	struct irq_data *irq_data;
+	int ret, ioapic, pin;
 	unsigned long flags;
 
 	if (!info || nr_irqs > 1)
@@ -2961,7 +3006,6 @@ int mp_irqdomain_alloc(struct irq_domain *domain, unsigned int virq,
 	if (!data)
 		return -ENOMEM;
 
-	info->ioapic.entry = &data->entry;
 	ret = irq_domain_alloc_irqs_parent(domain, virq, nr_irqs, info);
 	if (ret < 0) {
 		kfree(data);
@@ -2975,23 +3019,20 @@ int mp_irqdomain_alloc(struct irq_domain *domain, unsigned int virq,
 	irq_data->chip_data = data;
 	mp_irqdomain_get_attr(mp_pin_to_gsi(ioapic, pin), data, info);
 
-	cfg = irqd_cfg(irq_data);
 	add_pin_to_irq_node(data, ioapic_alloc_attr_node(info), ioapic, pin);
 
-	local_irq_save(flags);
-	if (info->ioapic.entry)
-		mp_setup_entry(cfg, data, info->ioapic.entry);
+	mp_preconfigure_entry(data);
 	mp_register_handler(virq, data->is_level);
+
+	local_irq_save(flags);
 	if (virq < nr_legacy_irqs())
 		legacy_pic->mask(virq);
 	local_irq_restore(flags);
 
 	apic_printk(APIC_VERBOSE, KERN_DEBUG
-		    "IOAPIC[%d]: Set routing entry (%d-%d -> 0x%x -> IRQ %d Mode:%i Active:%i Dest:%d)\n",
-		    ioapic, mpc_ioapic_id(ioapic), pin, cfg->vector,
-		    virq, data->is_level, data->active_low,
-		    cfg->dest_apicid);
-
+		    "IOAPIC[%d]: Preconfigured routing entry (%d-%d -> IRQ %d Level:%i ActiveLow:%i)\n",
+		    ioapic, mpc_ioapic_id(ioapic), pin, virq,
+		    data->is_level, data->active_low);
 	return 0;
 }
 
diff --git a/drivers/iommu/amd/iommu.c b/drivers/iommu/amd/iommu.c
index 3d72ec7bbbf8..9744cdbefd88 100644
--- a/drivers/iommu/amd/iommu.c
+++ b/drivers/iommu/amd/iommu.c
@@ -3669,7 +3669,6 @@ static void irq_remapping_prepare_irte(struct amd_ir_data *data,
 				       int devid, int index, int sub_handle)
 {
 	struct irq_2_irte *irte_info = &data->irq_2_irte;
-	struct IO_APIC_route_entry *entry;
 	struct amd_iommu *iommu = amd_iommu_rlookup_table[devid];
 
 	if (!iommu)
@@ -3683,17 +3682,6 @@ static void irq_remapping_prepare_irte(struct amd_ir_data *data,
 
 	switch (info->type) {
 	case X86_IRQ_ALLOC_TYPE_IOAPIC:
-		/* Setup IOAPIC entry */
-		entry = info->ioapic.entry;
-		info->ioapic.entry = NULL;
-		memset(entry, 0, sizeof(*entry));
-		entry->vector		= index;
-		entry->is_level		= info->ioapic.is_level;
-		entry->active_low	= info->ioapic.active_low;
-		/* Mask level triggered irqs. */
-		entry->masked		= info->ioapic.is_level;
-		break;
-
 	case X86_IRQ_ALLOC_TYPE_HPET:
 	case X86_IRQ_ALLOC_TYPE_PCI_MSI:
 	case X86_IRQ_ALLOC_TYPE_PCI_MSIX:
diff --git a/drivers/iommu/hyperv-iommu.c b/drivers/iommu/hyperv-iommu.c
index 1ab7eb918a5c..37dd485a5640 100644
--- a/drivers/iommu/hyperv-iommu.c
+++ b/drivers/iommu/hyperv-iommu.c
@@ -40,7 +40,6 @@ static int hyperv_ir_set_affinity(struct irq_data *data,
 {
 	struct irq_data *parent = data->parent_data;
 	struct irq_cfg *cfg = irqd_cfg(data);
-	struct IO_APIC_route_entry *entry;
 	int ret;
 
 	/* Return error If new irq affinity is out of ioapic_max_cpumask. */
@@ -51,9 +50,6 @@ static int hyperv_ir_set_affinity(struct irq_data *data,
 	if (ret < 0 || ret == IRQ_SET_MASK_OK_DONE)
 		return ret;
 
-	entry = data->chip_data;
-	entry->destid_0_7 = cfg->dest_apicid;
-	entry->vector = cfg->vector;
 	send_cleanup_vector(cfg);
 
 	return 0;
@@ -89,20 +85,6 @@ static int hyperv_irq_remapping_alloc(struct irq_domain *domain,
 
 	irq_data->chip = &hyperv_ir_chip;
 
-	/*
-	 * If there is interrupt remapping function of IOMMU, setting irq
-	 * affinity only needs to change IRTE of IOMMU. But Hyper-V doesn't
-	 * support interrupt remapping function, setting irq affinity of IO-APIC
-	 * interrupts still needs to change IO-APIC registers. But ioapic_
-	 * configure_entry() will ignore value of cfg->vector and cfg->
-	 * dest_apicid when IO-APIC's parent irq domain is not the vector
-	 * domain.(See ioapic_configure_entry()) In order to setting vector
-	 * and dest_apicid to IO-APIC register, IO-APIC entry pointer is saved
-	 * in the chip_data and hyperv_irq_remapping_activate()/hyperv_ir_set_
-	 * affinity() set vector and dest_apicid directly into IO-APIC entry.
-	 */
-	irq_data->chip_data = info->ioapic.entry;
-
 	/*
 	 * Hypver-V IO APIC irq affinity should be in the scope of
 	 * ioapic_max_cpumask because no irq remapping support.
@@ -119,22 +101,9 @@ static void hyperv_irq_remapping_free(struct irq_domain *domain,
 	irq_domain_free_irqs_common(domain, virq, nr_irqs);
 }
 
-static int hyperv_irq_remapping_activate(struct irq_domain *domain,
-			  struct irq_data *irq_data, bool reserve)
-{
-	struct irq_cfg *cfg = irqd_cfg(irq_data);
-	struct IO_APIC_route_entry *entry = irq_data->chip_data;
-
-	entry->destid_0_7 = cfg->dest_apicid;
-	entry->vector = cfg->vector;
-
-	return 0;
-}
-
 static const struct irq_domain_ops hyperv_ir_domain_ops = {
 	.alloc = hyperv_irq_remapping_alloc,
 	.free = hyperv_irq_remapping_free,
-	.activate = hyperv_irq_remapping_activate,
 };
 
 static int __init hyperv_prepare_irq_remapping(void)
diff --git a/drivers/iommu/intel/irq_remapping.c b/drivers/iommu/intel/irq_remapping.c
index 625bdb9f1627..96c84b19940e 100644
--- a/drivers/iommu/intel/irq_remapping.c
+++ b/drivers/iommu/intel/irq_remapping.c
@@ -1280,9 +1280,9 @@ static void intel_irq_remapping_prepare_irte(struct intel_ir_data *data,
 					     int index, int sub_handle)
 {
 	struct irte *irte = &data->irte_entry;
-	struct IO_APIC_route_entry *entry;
 
 	prepare_irte(irte, irq_cfg->vector, irq_cfg->dest_apicid);
+
 	switch (info->type) {
 	case X86_IRQ_ALLOC_TYPE_IOAPIC:
 		/* Set source-id of interrupt request */
@@ -1293,39 +1293,20 @@ static void intel_irq_remapping_prepare_irte(struct intel_ir_data *data,
 			irte->trigger_mode, irte->dlvry_mode,
 			irte->avail, irte->vector, irte->dest_id,
 			irte->sid, irte->sq, irte->svt);
-
-		entry = info->ioapic.entry;
-		info->ioapic.entry = NULL;
-		memset(entry, 0, sizeof(*entry));
-		entry->ir_index_15	= !!(index & 0x8000);
-		entry->ir_format	= true;
-		entry->ir_index_0_14	= index & 0x7fff;
-		/*
-		 * IO-APIC RTE will be configured with virtual vector.
-		 * irq handler will do the explicit EOI to the io-apic.
-		 */
-		entry->vector		= info->ioapic.pin;
-		entry->is_level		= info->ioapic.is_level;
-		entry->active_low	= info->ioapic.active_low;
-		/* Mask level triggered irqs. */
-		entry->masked		= info->ioapic.is_level;
+		sub_handle = info->ioapic.pin;
 		break;
-
 	case X86_IRQ_ALLOC_TYPE_HPET:
+		set_hpet_sid(irte, info->devid);
+		break;
 	case X86_IRQ_ALLOC_TYPE_PCI_MSI:
 	case X86_IRQ_ALLOC_TYPE_PCI_MSIX:
-		if (info->type == X86_IRQ_ALLOC_TYPE_HPET)
-			set_hpet_sid(irte, info->devid);
-		else
-			set_msi_sid(irte, msi_desc_to_pci_dev(info->desc));
-
-		fill_msi_msg(&data->msi_entry, index, sub_handle);
+		set_msi_sid(irte, msi_desc_to_pci_dev(info->desc));
 		break;
-
 	default:
 		BUG_ON(1);
 		break;
 	}
+	fill_msi_msg(&data->msi_entry, index, sub_handle);
 }
 
 static void intel_free_irq_resources(struct irq_domain *domain,
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 22/35] genirq/irqdomain: Implement get_name() method on irqchip fwnodes

[David Woodhouse]

From: David Woodhouse <dwmw@amazon.co.uk>

Prerequesite to make x86 more irqdomain compliant.

Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
---
 kernel/irq/irqdomain.c | 11 ++++++++++-
 1 file changed, 10 insertions(+), 1 deletion(-)

diff --git a/kernel/irq/irqdomain.c b/kernel/irq/irqdomain.c
index cf8b374b892d..673fa64c1c44 100644
--- a/kernel/irq/irqdomain.c
+++ b/kernel/irq/irqdomain.c
@@ -42,7 +42,16 @@ static inline void debugfs_add_domain_dir(struct irq_domain *d) { }
 static inline void debugfs_remove_domain_dir(struct irq_domain *d) { }
 #endif
 
-const struct fwnode_operations irqchip_fwnode_ops;
+static const char *irqchip_fwnode_get_name(const struct fwnode_handle *fwnode)
+{
+	struct irqchip_fwid *fwid = container_of(fwnode, struct irqchip_fwid, fwnode);
+
+	return fwid->name;
+}
+
+const struct fwnode_operations irqchip_fwnode_ops = {
+	.get_name = irqchip_fwnode_get_name,
+};
 EXPORT_SYMBOL_GPL(irqchip_fwnode_ops);
 
 /**
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

Re: [PATCH v3 22/35] genirq/irqdomain: Implement get_name() method on irqchip fwnodes

[Marc Zyngier]

Hi David,

nit: please use my kernel.org address for kernel related stuff.

On Sat, 24 Oct 2020 22:35:22 +0100,
David Woodhouse <dwmw2@infradead.org> wrote:
> 
> From: David Woodhouse <dwmw@amazon.co.uk>
> 
> Prerequesite to make x86 more irqdomain compliant.

Prerequisite?

> 
> Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
> ---
>  kernel/irq/irqdomain.c | 11 ++++++++++-
>  1 file changed, 10 insertions(+), 1 deletion(-)
> 
> diff --git a/kernel/irq/irqdomain.c b/kernel/irq/irqdomain.c
> index cf8b374b892d..673fa64c1c44 100644
> --- a/kernel/irq/irqdomain.c
> +++ b/kernel/irq/irqdomain.c
> @@ -42,7 +42,16 @@ static inline void debugfs_add_domain_dir(struct irq_domain *d) { }
>  static inline void debugfs_remove_domain_dir(struct irq_domain *d) { }
>  #endif
>  
> -const struct fwnode_operations irqchip_fwnode_ops;
> +static const char *irqchip_fwnode_get_name(const struct fwnode_handle *fwnode)
> +{
> +	struct irqchip_fwid *fwid = container_of(fwnode, struct irqchip_fwid, fwnode);
> +
> +	return fwid->name;
> +}
> +
> +const struct fwnode_operations irqchip_fwnode_ops = {
> +	.get_name = irqchip_fwnode_get_name,
> +};
>  EXPORT_SYMBOL_GPL(irqchip_fwnode_ops);
>  
>  /**

Acked-by: Marc Zyngier <maz@kernel.org>

-- 
Without deviation from the norm, progress is not possible.
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 23/35] x86/apic: Add select() method on vector irqdomain

[David Woodhouse]

From: David Woodhouse <dwmw@amazon.co.uk>

This will be used to select the irqdomain for I/O-APIC and HPET.

Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
---
 arch/x86/include/asm/irqdomain.h |  3 +++
 arch/x86/kernel/apic/vector.c    | 43 ++++++++++++++++++++++++++++++++
 2 files changed, 46 insertions(+)

diff --git a/arch/x86/include/asm/irqdomain.h b/arch/x86/include/asm/irqdomain.h
index cd684d45cb5f..125c23b7bad3 100644
--- a/arch/x86/include/asm/irqdomain.h
+++ b/arch/x86/include/asm/irqdomain.h
@@ -12,6 +12,9 @@ enum {
 	X86_IRQ_ALLOC_LEGACY				= 0x2,
 };
 
+extern int x86_fwspec_is_ioapic(struct irq_fwspec *fwspec);
+extern int x86_fwspec_is_hpet(struct irq_fwspec *fwspec);
+
 extern struct irq_domain *x86_vector_domain;
 
 extern void init_irq_alloc_info(struct irq_alloc_info *info,
diff --git a/arch/x86/kernel/apic/vector.c b/arch/x86/kernel/apic/vector.c
index bb2e2a2488a5..b9b05caa28a4 100644
--- a/arch/x86/kernel/apic/vector.c
+++ b/arch/x86/kernel/apic/vector.c
@@ -636,7 +636,50 @@ static void x86_vector_debug_show(struct seq_file *m, struct irq_domain *d,
 }
 #endif
 
+int x86_fwspec_is_ioapic(struct irq_fwspec *fwspec)
+{
+	if (fwspec->param_count != 1)
+		return 0;
+
+	if (is_fwnode_irqchip(fwspec->fwnode)) {
+		const char *fwname = fwnode_get_name(fwspec->fwnode);
+		return fwname && !strncmp(fwname, "IO-APIC-", 8) &&
+			simple_strtol(fwname+8, NULL, 10) == fwspec->param[0];
+	}
+	return to_of_node(fwspec->fwnode) &&
+		of_device_is_compatible(to_of_node(fwspec->fwnode),
+					"intel,ce4100-ioapic");
+}
+
+int x86_fwspec_is_hpet(struct irq_fwspec *fwspec)
+{
+	if (fwspec->param_count != 1)
+		return 0;
+
+	if (is_fwnode_irqchip(fwspec->fwnode)) {
+		const char *fwname = fwnode_get_name(fwspec->fwnode);
+		return fwname && !strncmp(fwname, "HPET-MSI-", 9) &&
+			simple_strtol(fwname+9, NULL, 10) == fwspec->param[0];
+	}
+	return 0;
+}
+
+static int x86_vector_select(struct irq_domain *d, struct irq_fwspec *fwspec,
+			     enum irq_domain_bus_token bus_token)
+{
+	/*
+	 * HPET and I/OAPIC cannot be parented in the vector domain
+	 * if IRQ remapping is enabled. APIC IDs above 15 bits are
+	 * only permitted if IRQ remapping is enabled, so check that.
+	 */
+	if (apic->apic_id_valid(32768))
+		return 0;
+
+	return x86_fwspec_is_ioapic(fwspec) || x86_fwspec_is_hpet(fwspec);
+}
+
 static const struct irq_domain_ops x86_vector_domain_ops = {
+	.select		= x86_vector_select,
 	.alloc		= x86_vector_alloc_irqs,
 	.free		= x86_vector_free_irqs,
 	.activate	= x86_vector_activate,
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 24/35] iommu/amd: Implement select() method on remapping irqdomain

[David Woodhouse]

From: David Woodhouse <dwmw@amazon.co.uk>

Preparatory change to remove irq_remapping_get_irq_domain().

Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
---
 drivers/iommu/amd/iommu.c | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/drivers/iommu/amd/iommu.c b/drivers/iommu/amd/iommu.c
index 9744cdbefd88..31b22244e9c2 100644
--- a/drivers/iommu/amd/iommu.c
+++ b/drivers/iommu/amd/iommu.c
@@ -3882,7 +3882,26 @@ static void irq_remapping_deactivate(struct irq_domain *domain,
 					    irte_info->index);
 }
 
+static int irq_remapping_select(struct irq_domain *d, struct irq_fwspec *fwspec,
+				enum irq_domain_bus_token bus_token)
+{
+	struct amd_iommu *iommu;
+	int devid = -1;
+
+	if (x86_fwspec_is_ioapic(fwspec))
+		devid = get_ioapic_devid(fwspec->param[0]);
+	else if (x86_fwspec_is_hpet(fwspec))
+		devid = get_hpet_devid(fwspec->param[0]);
+
+	if (devid < 0)
+		return 0;
+
+	iommu = amd_iommu_rlookup_table[devid];
+	return iommu && iommu->ir_domain == d;
+}
+
 static const struct irq_domain_ops amd_ir_domain_ops = {
+	.select = irq_remapping_select,
 	.alloc = irq_remapping_alloc,
 	.free = irq_remapping_free,
 	.activate = irq_remapping_activate,
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 25/35] iommu/vt-d: Implement select() method on remapping irqdomain

[David Woodhouse]

From: David Woodhouse <dwmw@amazon.co.uk>

Preparatory for removing irq_remapping_get_irq_domain()

Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
---
 drivers/iommu/intel/irq_remapping.c | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/drivers/iommu/intel/irq_remapping.c b/drivers/iommu/intel/irq_remapping.c
index 96c84b19940e..b3b079c0b51e 100644
--- a/drivers/iommu/intel/irq_remapping.c
+++ b/drivers/iommu/intel/irq_remapping.c
@@ -1431,7 +1431,20 @@ static void intel_irq_remapping_deactivate(struct irq_domain *domain,
 	modify_irte(&data->irq_2_iommu, &entry);
 }
 
+static int intel_irq_remapping_select(struct irq_domain *d,
+				      struct irq_fwspec *fwspec,
+				      enum irq_domain_bus_token bus_token)
+{
+	if (x86_fwspec_is_ioapic(fwspec))
+		return d == map_ioapic_to_ir(fwspec->param[0]);
+	else if (x86_fwspec_is_hpet(fwspec))
+		return d == map_hpet_to_ir(fwspec->param[0]);
+
+	return 0;
+}
+
 static const struct irq_domain_ops intel_ir_domain_ops = {
+	.select = intel_irq_remapping_select,
 	.alloc = intel_irq_remapping_alloc,
 	.free = intel_irq_remapping_free,
 	.activate = intel_irq_remapping_activate,
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 26/35] iommu/hyper-v: Implement select() method on remapping irqdomain

[David Woodhouse]

From: David Woodhouse <dwmw@amazon.co.uk>

Preparatory for removing irq_remapping_get_irq_domain()

Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
---
 drivers/iommu/hyperv-iommu.c | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/drivers/iommu/hyperv-iommu.c b/drivers/iommu/hyperv-iommu.c
index 37dd485a5640..78a264ad9405 100644
--- a/drivers/iommu/hyperv-iommu.c
+++ b/drivers/iommu/hyperv-iommu.c
@@ -101,7 +101,16 @@ static void hyperv_irq_remapping_free(struct irq_domain *domain,
 	irq_domain_free_irqs_common(domain, virq, nr_irqs);
 }
 
+static int hyperv_irq_remapping_select(struct irq_domain *d,
+				       struct irq_fwspec *fwspec,
+				       enum irq_domain_bus_token bus_token)
+{
+	/* Claim only the first (and only) I/OAPIC */
+	return x86_fwspec_is_ioapic(fwspec) && fwspec->param[0] == 0;
+}
+
 static const struct irq_domain_ops hyperv_ir_domain_ops = {
+	.select = hyperv_irq_remapping_select,
 	.alloc = hyperv_irq_remapping_alloc,
 	.free = hyperv_irq_remapping_free,
 };
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 27/35] x86/hpet: Use irq_find_matching_fwspec() to find remapping irqdomain

[David Woodhouse]

From: David Woodhouse <dwmw@amazon.co.uk>

All possible parent domains have a select method now. Make use of it.

Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
---
 arch/x86/kernel/hpet.c | 24 ++++++++++++++----------
 1 file changed, 14 insertions(+), 10 deletions(-)

diff --git a/arch/x86/kernel/hpet.c b/arch/x86/kernel/hpet.c
index 3b8b12769f3b..08651a4e6aa0 100644
--- a/arch/x86/kernel/hpet.c
+++ b/arch/x86/kernel/hpet.c
@@ -543,8 +543,8 @@ static struct irq_domain *hpet_create_irq_domain(int hpet_id)
 {
 	struct msi_domain_info *domain_info;
 	struct irq_domain *parent, *d;
-	struct irq_alloc_info info;
 	struct fwnode_handle *fn;
+	struct irq_fwspec fwspec;
 
 	if (x86_vector_domain == NULL)
 		return NULL;
@@ -556,15 +556,6 @@ static struct irq_domain *hpet_create_irq_domain(int hpet_id)
 	*domain_info = hpet_msi_domain_info;
 	domain_info->data = (void *)(long)hpet_id;
 
-	init_irq_alloc_info(&info, NULL);
-	info.type = X86_IRQ_ALLOC_TYPE_HPET_GET_PARENT;
-	info.devid = hpet_id;
-	parent = irq_remapping_get_irq_domain(&info);
-	if (parent == NULL)
-		parent = x86_vector_domain;
-	else
-		hpet_msi_controller.name = "IR-HPET-MSI";
-
 	fn = irq_domain_alloc_named_id_fwnode(hpet_msi_controller.name,
 					      hpet_id);
 	if (!fn) {
@@ -572,6 +563,19 @@ static struct irq_domain *hpet_create_irq_domain(int hpet_id)
 		return NULL;
 	}
 
+	fwspec.fwnode = fn;
+	fwspec.param_count = 1;
+	fwspec.param[0] = hpet_id;
+
+	parent = irq_find_matching_fwspec(&fwspec, DOMAIN_BUS_ANY);
+	if (!parent) {
+		irq_domain_free_fwnode(fn);
+		kfree(domain_info);
+		return NULL;
+	}
+	if (parent != x86_vector_domain)
+		hpet_msi_controller.name = "IR-HPET-MSI";
+
 	d = msi_create_irq_domain(fn, domain_info, parent);
 	if (!d) {
 		irq_domain_free_fwnode(fn);
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 28/35] x86/ioapic: Use irq_find_matching_fwspec() to find remapping irqdomain

[David Woodhouse]

From: David Woodhouse <dwmw@amazon.co.uk>

All possible parent domains have a select method now. Make use of it.

Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
---
 arch/x86/kernel/apic/io_apic.c | 25 +++++++++++++------------
 1 file changed, 13 insertions(+), 12 deletions(-)

diff --git a/arch/x86/kernel/apic/io_apic.c b/arch/x86/kernel/apic/io_apic.c
index ea983da1a57f..443d2c9086b9 100644
--- a/arch/x86/kernel/apic/io_apic.c
+++ b/arch/x86/kernel/apic/io_apic.c
@@ -2320,36 +2320,37 @@ static inline void __init check_timer(void)
 
 static int mp_irqdomain_create(int ioapic)
 {
-	struct irq_alloc_info info;
 	struct irq_domain *parent;
 	int hwirqs = mp_ioapic_pin_count(ioapic);
 	struct ioapic *ip = &ioapics[ioapic];
 	struct ioapic_domain_cfg *cfg = &ip->irqdomain_cfg;
 	struct mp_ioapic_gsi *gsi_cfg = mp_ioapic_gsi_routing(ioapic);
 	struct fwnode_handle *fn;
-	char *name = "IO-APIC";
+	struct irq_fwspec fwspec;
 
 	if (cfg->type == IOAPIC_DOMAIN_INVALID)
 		return 0;
 
-	init_irq_alloc_info(&info, NULL);
-	info.type = X86_IRQ_ALLOC_TYPE_IOAPIC_GET_PARENT;
-	info.devid = mpc_ioapic_id(ioapic);
-	parent = irq_remapping_get_irq_domain(&info);
-	if (!parent)
-		parent = x86_vector_domain;
-	else
-		name = "IO-APIC-IR";
-
 	/* Handle device tree enumerated APICs proper */
 	if (cfg->dev) {
 		fn = of_node_to_fwnode(cfg->dev);
 	} else {
-		fn = irq_domain_alloc_named_id_fwnode(name, ioapic);
+		fn = irq_domain_alloc_named_id_fwnode("IO-APIC", ioapic);
 		if (!fn)
 			return -ENOMEM;
 	}
 
+	fwspec.fwnode = fn;
+	fwspec.param_count = 1;
+	fwspec.param[0] = ioapic;
+
+	parent = irq_find_matching_fwspec(&fwspec, DOMAIN_BUS_ANY);
+	if (!parent) {
+		if (!cfg->dev)
+			irq_domain_free_fwnode(fn);
+		return -ENODEV;
+	}
+
 	ip->irqdomain = irq_domain_create_linear(fn, hwirqs, cfg->ops,
 						 (void *)(long)ioapic);
 
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 29/35] x86: Kill all traces of irq_remapping_get_irq_domain()

[David Woodhouse]

From: David Woodhouse <dwmw@amazon.co.uk>

All users are converted to use the fwspec based parent domain lookup.

Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
---
 arch/x86/include/asm/hw_irq.h        |  2 --
 arch/x86/include/asm/irq_remapping.h |  9 --------
 drivers/iommu/amd/iommu.c            | 34 ----------------------------
 drivers/iommu/hyperv-iommu.c         |  9 --------
 drivers/iommu/intel/irq_remapping.c  | 17 --------------
 drivers/iommu/irq_remapping.c        | 14 ------------
 drivers/iommu/irq_remapping.h        |  3 ---
 7 files changed, 88 deletions(-)

diff --git a/arch/x86/include/asm/hw_irq.h b/arch/x86/include/asm/hw_irq.h
index 83a69f62637e..458f5a676402 100644
--- a/arch/x86/include/asm/hw_irq.h
+++ b/arch/x86/include/asm/hw_irq.h
@@ -40,8 +40,6 @@ enum irq_alloc_type {
 	X86_IRQ_ALLOC_TYPE_PCI_MSIX,
 	X86_IRQ_ALLOC_TYPE_DMAR,
 	X86_IRQ_ALLOC_TYPE_UV,
-	X86_IRQ_ALLOC_TYPE_IOAPIC_GET_PARENT,
-	X86_IRQ_ALLOC_TYPE_HPET_GET_PARENT,
 };
 
 struct ioapic_alloc_info {
diff --git a/arch/x86/include/asm/irq_remapping.h b/arch/x86/include/asm/irq_remapping.h
index af4a151d70b3..7cc49432187f 100644
--- a/arch/x86/include/asm/irq_remapping.h
+++ b/arch/x86/include/asm/irq_remapping.h
@@ -44,9 +44,6 @@ extern int irq_remapping_reenable(int);
 extern int irq_remap_enable_fault_handling(void);
 extern void panic_if_irq_remap(const char *msg);
 
-extern struct irq_domain *
-irq_remapping_get_irq_domain(struct irq_alloc_info *info);
-
 /* Create PCI MSI/MSIx irqdomain, use @parent as the parent irqdomain. */
 extern struct irq_domain *
 arch_create_remap_msi_irq_domain(struct irq_domain *par, const char *n, int id);
@@ -71,11 +68,5 @@ static inline void panic_if_irq_remap(const char *msg)
 {
 }
 
-static inline struct irq_domain *
-irq_remapping_get_irq_domain(struct irq_alloc_info *info)
-{
-	return NULL;
-}
-
 #endif /* CONFIG_IRQ_REMAP */
 #endif /* __X86_IRQ_REMAPPING_H */
diff --git a/drivers/iommu/amd/iommu.c b/drivers/iommu/amd/iommu.c
index 31b22244e9c2..463d322a4f3b 100644
--- a/drivers/iommu/amd/iommu.c
+++ b/drivers/iommu/amd/iommu.c
@@ -3601,10 +3601,8 @@ static int get_devid(struct irq_alloc_info *info)
 {
 	switch (info->type) {
 	case X86_IRQ_ALLOC_TYPE_IOAPIC:
-	case X86_IRQ_ALLOC_TYPE_IOAPIC_GET_PARENT:
 		return get_ioapic_devid(info->devid);
 	case X86_IRQ_ALLOC_TYPE_HPET:
-	case X86_IRQ_ALLOC_TYPE_HPET_GET_PARENT:
 		return get_hpet_devid(info->devid);
 	case X86_IRQ_ALLOC_TYPE_PCI_MSI:
 	case X86_IRQ_ALLOC_TYPE_PCI_MSIX:
@@ -3615,44 +3613,12 @@ static int get_devid(struct irq_alloc_info *info)
 	}
 }
 
-static struct irq_domain *get_irq_domain_for_devid(struct irq_alloc_info *info,
-						   int devid)
-{
-	struct amd_iommu *iommu = amd_iommu_rlookup_table[devid];
-
-	if (!iommu)
-		return NULL;
-
-	switch (info->type) {
-	case X86_IRQ_ALLOC_TYPE_IOAPIC_GET_PARENT:
-	case X86_IRQ_ALLOC_TYPE_HPET_GET_PARENT:
-		return iommu->ir_domain;
-	default:
-		WARN_ON_ONCE(1);
-		return NULL;
-	}
-}
-
-static struct irq_domain *get_irq_domain(struct irq_alloc_info *info)
-{
-	int devid;
-
-	if (!info)
-		return NULL;
-
-	devid = get_devid(info);
-	if (devid < 0)
-		return NULL;
-	return get_irq_domain_for_devid(info, devid);
-}
-
 struct irq_remap_ops amd_iommu_irq_ops = {
 	.prepare		= amd_iommu_prepare,
 	.enable			= amd_iommu_enable,
 	.disable		= amd_iommu_disable,
 	.reenable		= amd_iommu_reenable,
 	.enable_faulting	= amd_iommu_enable_faulting,
-	.get_irq_domain		= get_irq_domain,
 };
 
 static void fill_msi_msg(struct msi_msg *msg, u32 index)
diff --git a/drivers/iommu/hyperv-iommu.c b/drivers/iommu/hyperv-iommu.c
index 78a264ad9405..a629a6be65c7 100644
--- a/drivers/iommu/hyperv-iommu.c
+++ b/drivers/iommu/hyperv-iommu.c
@@ -160,18 +160,9 @@ static int __init hyperv_enable_irq_remapping(void)
 	return IRQ_REMAP_X2APIC_MODE;
 }
 
-static struct irq_domain *hyperv_get_irq_domain(struct irq_alloc_info *info)
-{
-	if (info->type == X86_IRQ_ALLOC_TYPE_IOAPIC_GET_PARENT)
-		return ioapic_ir_domain;
-	else
-		return NULL;
-}
-
 struct irq_remap_ops hyperv_irq_remap_ops = {
 	.prepare		= hyperv_prepare_irq_remapping,
 	.enable			= hyperv_enable_irq_remapping,
-	.get_irq_domain		= hyperv_get_irq_domain,
 };
 
 #endif
diff --git a/drivers/iommu/intel/irq_remapping.c b/drivers/iommu/intel/irq_remapping.c
index b3b079c0b51e..bca44015bc1d 100644
--- a/drivers/iommu/intel/irq_remapping.c
+++ b/drivers/iommu/intel/irq_remapping.c
@@ -1127,29 +1127,12 @@ static void prepare_irte(struct irte *irte, int vector, unsigned int dest)
 	irte->redir_hint = 1;
 }
 
-static struct irq_domain *intel_get_irq_domain(struct irq_alloc_info *info)
-{
-	if (!info)
-		return NULL;
-
-	switch (info->type) {
-	case X86_IRQ_ALLOC_TYPE_IOAPIC_GET_PARENT:
-		return map_ioapic_to_ir(info->devid);
-	case X86_IRQ_ALLOC_TYPE_HPET_GET_PARENT:
-		return map_hpet_to_ir(info->devid);
-	default:
-		WARN_ON_ONCE(1);
-		return NULL;
-	}
-}
-
 struct irq_remap_ops intel_irq_remap_ops = {
 	.prepare		= intel_prepare_irq_remapping,
 	.enable			= intel_enable_irq_remapping,
 	.disable		= disable_irq_remapping,
 	.reenable		= reenable_irq_remapping,
 	.enable_faulting	= enable_drhd_fault_handling,
-	.get_irq_domain		= intel_get_irq_domain,
 };
 
 static void intel_ir_reconfigure_irte(struct irq_data *irqd, bool force)
diff --git a/drivers/iommu/irq_remapping.c b/drivers/iommu/irq_remapping.c
index 2d84b1ed205e..83314b9d8f38 100644
--- a/drivers/iommu/irq_remapping.c
+++ b/drivers/iommu/irq_remapping.c
@@ -158,17 +158,3 @@ void panic_if_irq_remap(const char *msg)
 	if (irq_remapping_enabled)
 		panic(msg);
 }
-
-/**
- * irq_remapping_get_irq_domain - Get the irqdomain serving the request @info
- * @info: interrupt allocation information, used to identify the IOMMU device
- *
- * Returns pointer to IRQ domain, or NULL on failure.
- */
-struct irq_domain *irq_remapping_get_irq_domain(struct irq_alloc_info *info)
-{
-	if (!remap_ops || !remap_ops->get_irq_domain)
-		return NULL;
-
-	return remap_ops->get_irq_domain(info);
-}
diff --git a/drivers/iommu/irq_remapping.h b/drivers/iommu/irq_remapping.h
index 1661b3d75920..8c89cb947cdb 100644
--- a/drivers/iommu/irq_remapping.h
+++ b/drivers/iommu/irq_remapping.h
@@ -42,9 +42,6 @@ struct irq_remap_ops {
 
 	/* Enable fault handling */
 	int  (*enable_faulting)(void);
-
-	/* Get the irqdomain associated to IOMMU device */
-	struct irq_domain *(*get_irq_domain)(struct irq_alloc_info *);
 };
 
 extern struct irq_remap_ops intel_irq_remap_ops;
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 30/35] iommu/vt-d: Simplify intel_irq_remapping_select()

[David Woodhouse]

From: David Woodhouse <dwmw@amazon.co.uk>

Now that the old get_irq_domain() method has gone, consolidate on just the
map_XXX_to_iommu() functions.

Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
---
 drivers/iommu/intel/irq_remapping.c | 19 +++++++------------
 1 file changed, 7 insertions(+), 12 deletions(-)

diff --git a/drivers/iommu/intel/irq_remapping.c b/drivers/iommu/intel/irq_remapping.c
index bca44015bc1d..aeffda92b10b 100644
--- a/drivers/iommu/intel/irq_remapping.c
+++ b/drivers/iommu/intel/irq_remapping.c
@@ -203,13 +203,13 @@ static int modify_irte(struct irq_2_iommu *irq_iommu,
 	return rc;
 }
 
-static struct irq_domain *map_hpet_to_ir(u8 hpet_id)
+static struct intel_iommu *map_hpet_to_iommu(u8 hpet_id)
 {
 	int i;
 
 	for (i = 0; i < MAX_HPET_TBS; i++) {
 		if (ir_hpet[i].id == hpet_id && ir_hpet[i].iommu)
-			return ir_hpet[i].iommu->ir_domain;
+			return ir_hpet[i].iommu;
 	}
 	return NULL;
 }
@@ -225,13 +225,6 @@ static struct intel_iommu *map_ioapic_to_iommu(int apic)
 	return NULL;
 }
 
-static struct irq_domain *map_ioapic_to_ir(int apic)
-{
-	struct intel_iommu *iommu = map_ioapic_to_iommu(apic);
-
-	return iommu ? iommu->ir_domain : NULL;
-}
-
 static struct irq_domain *map_dev_to_ir(struct pci_dev *dev)
 {
 	struct dmar_drhd_unit *drhd = dmar_find_matched_drhd_unit(dev);
@@ -1418,12 +1411,14 @@ static int intel_irq_remapping_select(struct irq_domain *d,
 				      struct irq_fwspec *fwspec,
 				      enum irq_domain_bus_token bus_token)
 {
+	struct intel_iommu *iommu = NULL;
+
 	if (x86_fwspec_is_ioapic(fwspec))
-		return d == map_ioapic_to_ir(fwspec->param[0]);
+		iommu = map_ioapic_to_iommu(fwspec->param[0]);
 	else if (x86_fwspec_is_hpet(fwspec))
-		return d == map_hpet_to_ir(fwspec->param[0]);
+		iommu = map_hpet_to_iommu(fwspec->param[0]);
 
-	return 0;
+	return iommu && d == iommu->ir_domain;
 }
 
 static const struct irq_domain_ops intel_ir_domain_ops = {
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 31/35] x86/ioapic: Handle Extended Destination ID field in RTE

[David Woodhouse]

From: David Woodhouse <dwmw@amazon.co.uk>

Bits 63-48 of the I/OAPIC Redirection Table Entry map directly to bits 19-4
of the address used in the resulting MSI cycle.

Historically, the x86 MSI format only used the top 8 of those 16 bits as
the destination APIC ID, and the "Extended Destination ID" in the lower 8
bits was unused.

With interrupt remapping, the lowest bit of the Extended Destination ID
(bit 48 of RTE, bit 4 of MSI address) is now used to indicate a remappable
format MSI.

A hypervisor can use the other 7 bits of the Extended Destination ID to
permit guests to address up to 15 bits of APIC IDs, thus allowing 32768
vCPUs before having to expose a vIOMMU and interrupt remapping to the
guest.

No behavioural change in this patch, since nothing yet permits APIC IDs
above 255 to be used with the non-IR I/OAPIC domain.

[ tglx: Converted it to the cleaned up entry/msi_msg format and added
  	commentry ]

Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
---
 arch/x86/include/asm/io_apic.h |  3 ++-
 arch/x86/kernel/apic/io_apic.c | 20 +++++++++++++++-----
 2 files changed, 17 insertions(+), 6 deletions(-)

diff --git a/arch/x86/include/asm/io_apic.h b/arch/x86/include/asm/io_apic.h
index 73da644b2f0d..437aa8d00e53 100644
--- a/arch/x86/include/asm/io_apic.h
+++ b/arch/x86/include/asm/io_apic.h
@@ -67,7 +67,8 @@ struct IO_APIC_route_entry {
 				is_level		:  1,
 				masked			:  1,
 				reserved_0		: 15,
-				reserved_1		: 24,
+				reserved_1		: 17,
+				virt_destid_8_14	:  7,
 				destid_0_7		:  8;
 		};
 		struct {
diff --git a/arch/x86/kernel/apic/io_apic.c b/arch/x86/kernel/apic/io_apic.c
index 443d2c9086b9..1cfd65ef295b 100644
--- a/arch/x86/kernel/apic/io_apic.c
+++ b/arch/x86/kernel/apic/io_apic.c
@@ -1238,9 +1238,10 @@ static void io_apic_print_entries(unsigned int apic, unsigned int nr_entries)
 			       (entry.ir_index_15 << 15) | entry.ir_index_0_14,
 				entry.ir_zero);
 		} else {
-			printk(KERN_DEBUG "%s, %s, D(%02X), M(%1d)\n", buf,
+			printk(KERN_DEBUG "%s, %s, D(%02X%02X), M(%1d)\n", buf,
 			       entry.dest_mode_logical ? "logical " : "physical",
-			       entry.destid_0_7, entry.delivery_mode);
+			       entry.virt_destid_8_14, entry.destid_0_7,
+			       entry.delivery_mode);
 		}
 	}
 }
@@ -1409,6 +1410,7 @@ void native_restore_boot_irq_mode(void)
 	 */
 	if (ioapic_i8259.pin != -1) {
 		struct IO_APIC_route_entry entry;
+		u32 apic_id = read_apic_id();
 
 		memset(&entry, 0, sizeof(entry));
 		entry.masked		= false;
@@ -1416,7 +1418,8 @@ void native_restore_boot_irq_mode(void)
 		entry.active_low	= false;
 		entry.dest_mode_logical	= false;
 		entry.delivery_mode	= APIC_DELIVERY_MODE_EXTINT;
-		entry.destid_0_7	= read_apic_id();
+		entry.destid_0_7	= apic_id & 0xFF;
+		entry.virt_destid_8_14	= apic_id >> 8;
 
 		/*
 		 * Add it to the IO-APIC irq-routing table:
@@ -1885,7 +1888,11 @@ static void ioapic_setup_msg_from_msi(struct irq_data *irq_data,
 	/* DMAR/IR: 1, 0 for all other modes */
 	entry->ir_format		= msg.arch_addr_lo.dmar_format;
 	/*
-	 * DMAR/IR: index bit 0-14.
+	 * - DMAR/IR: index bit 0-14.
+	 *
+	 * - Virt: If the host supports x2apic without a virtualized IR
+	 *	   unit then bit 0-6 of dmar_index_0_14 are providing bit
+	 *	   8-14 of the destination id.
 	 *
 	 * All other modes have bit 0-6 of dmar_index_0_14 cleared and the
 	 * topmost 8 bits are destination id bit 0-7 (entry::destid_0_7).
@@ -2063,6 +2070,7 @@ static inline void __init unlock_ExtINT_logic(void)
 	int apic, pin, i;
 	struct IO_APIC_route_entry entry0, entry1;
 	unsigned char save_control, save_freq_select;
+	u32 apic_id;
 
 	pin  = find_isa_irq_pin(8, mp_INT);
 	if (pin == -1) {
@@ -2078,11 +2086,13 @@ static inline void __init unlock_ExtINT_logic(void)
 	entry0 = ioapic_read_entry(apic, pin);
 	clear_IO_APIC_pin(apic, pin);
 
+	apic_id = hard_smp_processor_id();
 	memset(&entry1, 0, sizeof(entry1));
 
 	entry1.dest_mode_logical	= true;
 	entry1.masked			= false;
-	entry1.destid_0_7		= hard_smp_processor_id();
+	entry1.destid_0_7		= apic_id & 0xFF;
+	entry1.virt_destid_8_14		= apic_id >> 8;
 	entry1.delivery_mode		= APIC_DELIVERY_MODE_EXTINT;
 	entry1.active_low		= entry0.active_low;
 	entry1.is_level			= false;
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 32/35] x86/apic: Support 15 bits of APIC ID in MSI where available

[David Woodhouse]

From: David Woodhouse <dwmw@amazon.co.uk>

Some hypervisors can allow the guest to use the Extended Destination ID
field in the MSI address to address up to 32768 CPUs.

This applies to all downstream devices which generate MSI cycles,
including HPET, I/OAPIC and PCI MSI.

HPET and PCI MSI use the same __irq_msi_compose_msg() function, while
I/OAPIC generates its own and had support for the extended bits added in
a previous commit.

Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201009104616.1314746-6-dwmw2@infradead.org
---
 arch/x86/include/asm/msi.h      |  3 ++-
 arch/x86/include/asm/x86_init.h |  2 ++
 arch/x86/kernel/apic/apic.c     | 26 ++++++++++++++++++++++++--
 arch/x86/kernel/x86_init.c      |  1 +
 4 files changed, 29 insertions(+), 3 deletions(-)

diff --git a/arch/x86/include/asm/msi.h b/arch/x86/include/asm/msi.h
index 322fd905da9c..b85147d75626 100644
--- a/arch/x86/include/asm/msi.h
+++ b/arch/x86/include/asm/msi.h
@@ -29,7 +29,8 @@ typedef struct x86_msi_addr_lo {
 			u32	reserved_0		:  2,
 				dest_mode_logical	:  1,
 				redirect_hint		:  1,
-				reserved_1		:  8,
+				reserved_1		:  1,
+				virt_destid_8_14	:  7,
 				destid_0_7		:  8,
 				base_address		: 12;
 		};
diff --git a/arch/x86/include/asm/x86_init.h b/arch/x86/include/asm/x86_init.h
index dde5b3f1e7cd..5c69f7eb5d47 100644
--- a/arch/x86/include/asm/x86_init.h
+++ b/arch/x86/include/asm/x86_init.h
@@ -116,6 +116,7 @@ struct x86_init_pci {
  * @init_platform:		platform setup
  * @guest_late_init:		guest late init
  * @x2apic_available:		X2APIC detection
+ * @msi_ext_dest_id:		MSI supports 15-bit APIC IDs
  * @init_mem_mapping:		setup early mappings during init_mem_mapping()
  * @init_after_bootmem:		guest init after boot allocator is finished
  */
@@ -123,6 +124,7 @@ struct x86_hyper_init {
 	void (*init_platform)(void);
 	void (*guest_late_init)(void);
 	bool (*x2apic_available)(void);
+	bool (*msi_ext_dest_id)(void);
 	void (*init_mem_mapping)(void);
 	void (*init_after_bootmem)(void);
 };
diff --git a/arch/x86/kernel/apic/apic.c b/arch/x86/kernel/apic/apic.c
index f7196ee0f005..6bd20c0de8bc 100644
--- a/arch/x86/kernel/apic/apic.c
+++ b/arch/x86/kernel/apic/apic.c
@@ -93,6 +93,11 @@ static unsigned int disabled_cpu_apicid __ro_after_init = BAD_APICID;
  */
 static int apic_extnmi __ro_after_init = APIC_EXTNMI_BSP;
 
+/*
+ * Hypervisor supports 15 bits of APIC ID in MSI Extended Destination ID
+ */
+static bool virt_ext_dest_id __ro_after_init;
+
 /*
  * Map cpu index to physical APIC ID
  */
@@ -1841,6 +1846,8 @@ static __init void try_to_enable_x2apic(int remap_mode)
 		return;
 
 	if (remap_mode != IRQ_REMAP_X2APIC_MODE) {
+		u32 apic_limit = 255;
+
 		/*
 		 * Using X2APIC without IR is not architecturally supported
 		 * on bare metal but may be supported in guests.
@@ -1851,12 +1858,22 @@ static __init void try_to_enable_x2apic(int remap_mode)
 			return;
 		}
 
+		/*
+		 * If the hypervisor supports extended destination ID in
+		 * MSI, that increases the maximum APIC ID that can be
+		 * used for non-remapped IRQ domains.
+		 */
+		if (x86_init.hyper.msi_ext_dest_id()) {
+			virt_ext_dest_id = 1;
+			apic_limit = 32767;
+		}
+
 		/*
 		 * Without IR, all CPUs can be addressed by IOAPIC/MSI only
 		 * in physical mode, and CPUs with an APIC ID that cannnot
 		 * be addressed must not be brought online.
 		 */
-		x2apic_set_max_apicid(255);
+		x2apic_set_max_apicid(apic_limit);
 		x2apic_phys = 1;
 	}
 	x2apic_enable();
@@ -2497,10 +2514,15 @@ void __irq_msi_compose_msg(struct irq_cfg *cfg, struct msi_msg *msg,
 	 * Only the IOMMU itself can use the trick of putting destination
 	 * APIC ID into the high bits of the address. Anything else would
 	 * just be writing to memory if it tried that, and needs IR to
-	 * address higher APIC IDs.
+	 * address APICs which can't be addressed in the normal 32-bit
+	 * address range at 0xFFExxxxx. That is typically just 8 bits, but
+	 * some hypervisors allow the extended destination ID field in bits
+	 * 5-11 to be used, giving support for 15 bits of APIC IDs in total.
 	 */
 	if (dmar)
 		msg->arch_addr_hi.destid_8_31 = cfg->dest_apicid >> 8;
+	else if (virt_ext_dest_id && cfg->dest_apicid < 0x8000)
+		msg->arch_addr_lo.virt_destid_8_14 = cfg->dest_apicid >> 8;
 	else
 		WARN_ON_ONCE(cfg->dest_apicid > 0xFF);
 }
diff --git a/arch/x86/kernel/x86_init.c b/arch/x86/kernel/x86_init.c
index a3038d8deb6a..8b395821cb8d 100644
--- a/arch/x86/kernel/x86_init.c
+++ b/arch/x86/kernel/x86_init.c
@@ -110,6 +110,7 @@ struct x86_init_ops x86_init __initdata = {
 		.init_platform		= x86_init_noop,
 		.guest_late_init	= x86_init_noop,
 		.x2apic_available	= bool_x86_init_noop,
+		.msi_ext_dest_id	= bool_x86_init_noop,
 		.init_mem_mapping	= x86_init_noop,
 		.init_after_bootmem	= x86_init_noop,
 	},
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 33/35] iommu/hyper-v: Disable IRQ pseudo-remapping if 15 bit APIC IDs are available

[David Woodhouse]

From: David Woodhouse <dwmw@amazon.co.uk>

If the 15-bit APIC ID support is present in emulated MSI then there's no
need for the pseudo-remapping support.

Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
---
 drivers/iommu/hyperv-iommu.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/iommu/hyperv-iommu.c b/drivers/iommu/hyperv-iommu.c
index a629a6be65c7..9438daa24fdb 100644
--- a/drivers/iommu/hyperv-iommu.c
+++ b/drivers/iommu/hyperv-iommu.c
@@ -121,6 +121,7 @@ static int __init hyperv_prepare_irq_remapping(void)
 	int i;
 
 	if (!hypervisor_is_type(X86_HYPER_MS_HYPERV) ||
+	    x86_init.hyper.msi_ext_dest_id() ||
 	    !x2apic_supported())
 		return -ENODEV;
 
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 34/35] x86/kvm: Reserve KVM_FEATURE_MSI_EXT_DEST_ID

[David Woodhouse]

From: David Woodhouse <dwmw@amazon.co.uk>

No functional change; just reserve the feature bit for now so that VMMs
can start to implement it.

This will allow the host to indicate that MSI emulation supports 15-bit
destination IDs, allowing up to 32768 CPUs without interrupt remapping.

cf. https://patchwork.kernel.org/patch/11816693/ for qemu

Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
---
 Documentation/virt/kvm/cpuid.rst     | 4 ++++
 arch/x86/include/uapi/asm/kvm_para.h | 1 +
 2 files changed, 5 insertions(+)

diff --git a/Documentation/virt/kvm/cpuid.rst b/Documentation/virt/kvm/cpuid.rst
index 9150e9d1c39b..f70b655821d5 100644
--- a/Documentation/virt/kvm/cpuid.rst
+++ b/Documentation/virt/kvm/cpuid.rst
@@ -92,6 +92,10 @@ KVM_FEATURE_ASYNC_PF_INT          14          guest checks this feature bit
                                               async pf acknowledgment msr
                                               0x4b564d07.
 
+KVM_FEATURE_MSI_EXT_DEST_ID       15          guest checks this feature bit
+                                              before using extended destination
+                                              ID bits in MSI address bits 11-5.
+
 KVM_FEATURE_CLOCSOURCE_STABLE_BIT 24          host will warn if no guest-side
                                               per-cpu warps are expeced in
                                               kvmclock
diff --git a/arch/x86/include/uapi/asm/kvm_para.h b/arch/x86/include/uapi/asm/kvm_para.h
index 812e9b4c1114..950afebfba88 100644
--- a/arch/x86/include/uapi/asm/kvm_para.h
+++ b/arch/x86/include/uapi/asm/kvm_para.h
@@ -32,6 +32,7 @@
 #define KVM_FEATURE_POLL_CONTROL	12
 #define KVM_FEATURE_PV_SCHED_YIELD	13
 #define KVM_FEATURE_ASYNC_PF_INT	14
+#define KVM_FEATURE_MSI_EXT_DEST_ID	15
 
 #define KVM_HINTS_REALTIME      0
 
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

[PATCH v3 35/35] x86/kvm: Enable 15-bit extension when KVM_FEATURE_MSI_EXT_DEST_ID detected

[David Woodhouse]

From: David Woodhouse <dwmw@amazon.co.uk>

This allows the host to indicate that MSI emulation supports 15-bit
destination IDs, allowing up to 32768 CPUs without interrupt remapping.

cf. https://patchwork.kernel.org/patch/11816693/ for qemu

Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
---
 arch/x86/kernel/kvm.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/x86/kernel/kvm.c b/arch/x86/kernel/kvm.c
index 1c0f2560a41c..b82de2843814 100644
--- a/arch/x86/kernel/kvm.c
+++ b/arch/x86/kernel/kvm.c
@@ -740,6 +740,11 @@ static void __init kvm_apic_init(void)
 #endif
 }
 
+static bool __init kvm_msi_ext_dest_id(void)
+{
+	return kvm_para_has_feature(KVM_FEATURE_MSI_EXT_DEST_ID);
+}
+
 static void __init kvm_init_platform(void)
 {
 	kvmclock_init();
@@ -769,6 +774,7 @@ const __initconst struct hypervisor_x86 x86_hyper_kvm = {
 	.type				= X86_HYPER_KVM,
 	.init.guest_late_init		= kvm_guest_init,
 	.init.x2apic_available		= kvm_para_available,
+	.init.msi_ext_dest_id		= kvm_msi_ext_dest_id,
 	.init.init_platform		= kvm_init_platform,
 #if defined(CONFIG_AMD_MEM_ENCRYPT)
 	.runtime.sev_es_hcall_prepare	= kvm_sev_es_hcall_prepare,
-- 
2.26.2

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

Re: [PATCH v3 00/35] Fix x2apic enablement and allow more CPUs, clean up I/OAPIC and MSI bitfields

[David Woodhouse]

[-- Attachment #1.1: Type: text/plain, Size: 1410 bytes --]

On Sat, 2020-10-24 at 22:35 +0100, David Woodhouse wrote:
> Fix the conditions for enabling x2apic on guests without interrupt 
> remapping, and support 15-bit Extended Destination ID to allow 32768 
> CPUs without IR on hypervisors that support it.
> 
> Make the I/OAPIC code generate its RTE directly from the MSI message
> created by the parent irqchip, and fix up a bunch of magic mask/shift
> macros to use bitfields for MSI messages and I/OAPIC RTEs while we're
> at it.

Forgot to mention (since I thought I'd posted it in a previous series)
that v3 also ditches irq_remapping_get_irq_domain() and some icky
special cases of hard-coding "x86_vector_domain", and makes HPET and
I/OAPIC use irq_find_matching_fwspeC() to find their parent irqdomain.

> v3:
>  • Lots of bitfield cleanups from Thomas.
>  • Disable hyperv-iommu if 15-bit extension is present.
>  • Fix inconsistent CONFIG_PCI_MSI/CONFIG_GENERIC_MSI_IRQ in hpet.c
>  • Split KVM_FEATURE_MSI_EXT_DEST_ID patch, half of which is going upstream
>    through KVM tree (and the other half needs to wait, or have an #ifdef) so
>    is left at the top of the tree.
> 
> v2:
>  • Minor cleanups.
>  • Move __irq_msi_compose_msg() to apic.c, make virt_ext_dest_id static.
>  • Generate I/OAPIC RTE directly from parent irqchip's MSI messages.
>  • Clean up HPET MSI support into hpet.c now that we can.


[-- Attachment #1.2: smime.p7s --]
[-- Type: application/x-pkcs7-signature, Size: 5174 bytes --]

[-- Attachment #2: Type: text/plain, Size: 156 bytes --]

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu