Re: [PATCH 06/11] RISC-V: drivers/iommu/riscv: Add command, fault, page-req queues

[Zong Li <zong.li@sifive.com>]

On Fri, Jul 28, 2023 at 1:19 PM Tomasz Jeznach <tjeznach@rivosinc.com> wrote:
>
> On Mon, Jul 24, 2023 at 11:47 AM Zong Li <zong.li@sifive.com> wrote:
> >
> > On Fri, Jul 21, 2023 at 2:00 AM Tomasz Jeznach <tjeznach@rivosinc.com> wrote:
> > >
> > > On Wed, Jul 19, 2023 at 8:12 PM Nick Kossifidis <mick@ics.forth.gr> wrote:
> > > >
> > > > Hello Tomasz,
> > > >
> > > > On 7/19/23 22:33, Tomasz Jeznach wrote:
> > > > > Enables message or wire signal interrupts for PCIe and platforms devices.
> > > > >
> > > >
> > > > The description doesn't match the subject nor the patch content (we
> > > > don't jus enable interrupts, we also init the queues).
> > > >
> > > > > +     /* Parse Queue lengts */
> > > > > +     ret = of_property_read_u32(pdev->dev.of_node, "cmdq_len", &iommu->cmdq_len);
> > > > > +     if (!ret)
> > > > > +             dev_info(dev, "command queue length set to %i\n", iommu->cmdq_len);
> > > > > +
> > > > > +     ret = of_property_read_u32(pdev->dev.of_node, "fltq_len", &iommu->fltq_len);
> > > > > +     if (!ret)
> > > > > +             dev_info(dev, "fault/event queue length set to %i\n", iommu->fltq_len);
> > > > > +
> > > > > +     ret = of_property_read_u32(pdev->dev.of_node, "priq_len", &iommu->priq_len);
> > > > > +     if (!ret)
> > > > > +             dev_info(dev, "page request queue length set to %i\n", iommu->priq_len);
> > > > > +
> > > > >       dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64));
> > > > >
> > > >
> > > > We need to add those to the device tree binding doc (or throw them away,
> > > > I thought it would be better to have them as part of the device
> > > > desciption than a module parameter).
> > > >
> > >
> > > We can add them as an optional fields to DT.
> > > Alternatively, I've been looking into an option to auto-scale CQ/PQ
> > > based on number of attached devices, but this gets trickier for
> > > hot-pluggable systems. I've added module parameters as a bare-minimum,
> > > but still looking for better solutions.
> > >
> > > >
> > > > > +static irqreturn_t riscv_iommu_priq_irq_check(int irq, void *data);
> > > > > +static irqreturn_t riscv_iommu_priq_process(int irq, void *data);
> > > > > +
> > > >
> > > > > +     case RISCV_IOMMU_PAGE_REQUEST_QUEUE:
> > > > > +             q = &iommu->priq;
> > > > > +             q->len = sizeof(struct riscv_iommu_pq_record);
> > > > > +             count = iommu->priq_len;
> > > > > +             irq = iommu->irq_priq;
> > > > > +             irq_check = riscv_iommu_priq_irq_check;
> > > > > +             irq_process = riscv_iommu_priq_process;
> > > > > +             q->qbr = RISCV_IOMMU_REG_PQB;
> > > > > +             q->qcr = RISCV_IOMMU_REG_PQCSR;
> > > > > +             name = "priq";
> > > > > +             break;
> > > >
> > > >
> > > > It makes more sense to add the code for the page request queue in the
> > > > patch that adds ATS/PRI support IMHO. This comment also applies to its
> > > > interrupt handlers below.
> > > >
> > >
> > > ack. will do.
> > >
> > > >
> > > > > +static inline void riscv_iommu_cmd_inval_set_addr(struct riscv_iommu_command *cmd,
> > > > > +                                               u64 addr)
> > > > > +{
> > > > > +     cmd->dword0 |= RISCV_IOMMU_CMD_IOTINVAL_AV;
> > > > > +     cmd->dword1 = addr;
> > > > > +}
> > > > > +
> > > >
> > > > This needs to be (addr >> 2) to match the spec, same as in the iofence
> > > > command.
> > > >
> > >
> > > oops. Thanks!
> > >
> >
> > I think it should be (addr >> 12) according to the spec.
> >
>
> My reading of the spec '3.1.1. IOMMU Page-Table cache invalidation commands'
> is that it is a 4k page aligned address packed at dword1[61:10], so
> effectively shifted by 2 bits.

Thanks for your clarifying. Just an opinion, perhaps you can use
'FIELD_PREP()' on it as well, it might be clearer.

>
> regards,
> - Tomasz
>
> > > > Regards,
> > > > Nick
> > > >
> > >
> > > regards,
> > > - Tomasz
> > >
> > > _______________________________________________
> > > linux-riscv mailing list
> > > linux-riscv@lists.infradead.org
> > > http://lists.infradead.org/mailman/listinfo/linux-riscv