Linux-MIPS Archive on lore.kernel.org
 help / color / Atom feed
* Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v7.
@ 2019-12-10 12:02 周琰杰 (Zhou Yanjie)
  2019-12-10 12:02 ` [PATCH v8 1/4] MIPS: Ingenic: Add Ingenic X1000 support 周琰杰 (Zhou Yanjie)
                   ` (3 more replies)
  0 siblings, 4 replies; 11+ messages in thread
From: 周琰杰 (Zhou Yanjie) @ 2019-12-10 12:02 UTC (permalink / raw)
  To: linux-mips
  Cc: linux-kernel, devicetree, robh+dt, paul.burton, paulburton,
	jhogan, mripard, shawnguo, mark.rutland, alexandre.belloni, ralf,
	heiko, icenowy, ak, laurent.pinchart, krzk, geert+renesas, paul,
	prasannatsmkumar, keescook, ebiederm, sernia.zhou, zhenwenjin,
	772753199

v7->v8:
1.Change "mac@134b0000" to "ethernet@134b0000", change "msc@13450000"
  to "mmc@13450000", change "msc@13460000" to "mmc@13460000".
2.Merge [5/6] in v7 to [1/4] of v8, merge [6/6] in v7 to [4/4] of v8.


^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH v8 1/4] MIPS: Ingenic: Add Ingenic X1000 support.
  2019-12-10 12:02 Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v7 周琰杰 (Zhou Yanjie)
@ 2019-12-10 12:02 ` 周琰杰 (Zhou Yanjie)
  2020-01-09 18:52   ` Paul Burton
  2019-12-10 12:02 ` [PATCH v8 2/4] dt-bindings: Document yna vendor-prefix 周琰杰 (Zhou Yanjie)
                   ` (2 subsequent siblings)
  3 siblings, 1 reply; 11+ messages in thread
From: 周琰杰 (Zhou Yanjie) @ 2019-12-10 12:02 UTC (permalink / raw)
  To: linux-mips
  Cc: linux-kernel, devicetree, robh+dt, paul.burton, paulburton,
	jhogan, mripard, shawnguo, mark.rutland, alexandre.belloni, ralf,
	heiko, icenowy, ak, laurent.pinchart, krzk, geert+renesas, paul,
	prasannatsmkumar, keescook, ebiederm, sernia.zhou, zhenwenjin,
	772753199

Support the Ingenic X1000 SoC using the code under arch/mips/jz4740.
This is left unselectable in Kconfig until a X1000 based board is
added in a later commit.

Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
---

Notes:
    v1->v2:
    Rebase on top of mips-next, use ingenic-timer driver
    for system timer and clocksource.
    
    v2->v3:
    Drop the 'apb' node.
    
    v3->v4:
    Adjust the node order to make it consistent with
    other Ingenic boards.
    
    v4->v5:
    No change.
    
    v5->v6:
    No change.
    
    v6->v7:
    Change my Signed-off-by from "Zhou Yanjie <zhouyanjie@zoho.com>"
    to "周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>" because
    the old mailbox is in an unstable state.
    
    v7->v8:
    Merge [5/6] in v7 to this patch.

 arch/mips/boot/dts/ingenic/x1000.dtsi | 272 ++++++++++++++++++++++++++++++++++
 arch/mips/jz4740/Kconfig              |   6 +
 2 files changed, 278 insertions(+)
 create mode 100644 arch/mips/boot/dts/ingenic/x1000.dtsi

diff --git a/arch/mips/boot/dts/ingenic/x1000.dtsi b/arch/mips/boot/dts/ingenic/x1000.dtsi
new file mode 100644
index 00000000..61061a4
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/x1000.dtsi
@@ -0,0 +1,272 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/clock/x1000-cgu.h>
+#include <dt-bindings/dma/x1000-dma.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "ingenic,x1000", "ingenic,x1000e";
+
+	cpuintc: interrupt-controller {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	intc: interrupt-controller@10001000 {
+		compatible = "ingenic,x1000-intc", "ingenic,jz4780-intc";
+		reg = <0x10001000 0x50>;
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&cpuintc>;
+		interrupts = <2>;
+	};
+
+	exclk: ext {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+	};
+
+	rtclk: rtc {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+
+	cgu: x1000-cgu@10000000 {
+		compatible = "ingenic,x1000-cgu";
+		reg = <0x10000000 0x100>;
+
+		#clock-cells = <1>;
+
+		clocks = <&exclk>, <&rtclk>;
+		clock-names = "ext", "rtc";
+	};
+
+	tcu: timer@10002000 {
+		compatible = "ingenic,x1000-tcu",
+				 "ingenic,jz4770-tcu",
+				 "simple-mfd";
+		reg = <0x10002000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x10002000 0x1000>;
+
+		#clock-cells = <1>;
+
+		clocks = <&cgu X1000_CLK_RTCLK
+			  &cgu X1000_CLK_EXCLK
+			  &cgu X1000_CLK_PCLK>;
+		clock-names = "rtc", "ext", "pclk";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <27 26 25>;
+
+		wdt: watchdog@0 {
+			compatible = "ingenic,x1000-watchdog", "ingenic,jz4780-watchdog";
+			reg = <0x0 0x10>;
+
+			clocks = <&cgu X1000_CLK_RTCLK>;
+			clock-names = "wdt";
+		};
+	};
+
+	rtc: rtc@10003000 {
+		compatible = "ingenic,x1000-rtc", "ingenic,jz4780-rtc";
+		reg = <0x10003000 0x4c>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <32>;
+
+		clocks = <&cgu X1000_CLK_RTCLK>;
+		clock-names = "rtc";
+	};
+
+	pinctrl: pin-controller@10010000 {
+		compatible = "ingenic,x1000-pinctrl";
+		reg = <0x10010000 0x800>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpa: gpio@0 {
+			compatible = "ingenic,x1000-gpio";
+			reg = <0>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 0 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <17>;
+		};
+
+		gpb: gpio@1 {
+			compatible = "ingenic,x1000-gpio";
+			reg = <1>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 32 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <16>;
+		};
+
+		gpc: gpio@2 {
+			compatible = "ingenic,x1000-gpio";
+			reg = <2>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 64 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <15>;
+		};
+
+		gpd: gpio@3 {
+			compatible = "ingenic,x1000-gpio";
+			reg = <3>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 96 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <14>;
+		};
+	};
+
+	uart0: serial@10030000 {
+		compatible = "ingenic,x1000-uart";
+		reg = <0x10030000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <51>;
+
+		clocks = <&exclk>, <&cgu X1000_CLK_UART0>;
+		clock-names = "baud", "module";
+
+		status = "disabled";
+	};
+
+	uart1: serial@10031000 {
+		compatible = "ingenic,x1000-uart";
+		reg = <0x10031000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <50>;
+
+		clocks = <&exclk>, <&cgu X1000_CLK_UART1>;
+		clock-names = "baud", "module";
+
+		status = "disabled";
+	};
+
+	uart2: serial@10032000 {
+		compatible = "ingenic,x1000-uart";
+		reg = <0x10032000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <49>;
+
+		clocks = <&exclk>, <&cgu X1000_CLK_UART2>;
+		clock-names = "baud", "module";
+
+		status = "disabled";
+	};
+
+	pdma: dma-controller@13420000 {
+		compatible = "ingenic,x1000-dma";
+		reg = <0x13420000 0x400
+			   0x13421000 0x40>;
+		#dma-cells = <2>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <10>;
+
+		clocks = <&cgu X1000_CLK_PDMA>;
+	};
+
+	mac: ethernet@134b0000 {
+		compatible = "ingenic,x1000-mac", "snps,dwmac";
+		reg = <0x134b0000 0x2000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <55>;
+		interrupt-names = "macirq";
+
+		clocks = <&cgu X1000_CLK_MAC>;
+		clock-names = "stmmaceth";
+
+		status = "disabled";
+
+		mdio: mdio {
+			compatible = "snps,dwmac-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+	};
+
+	msc0: mmc@13450000 {
+		compatible = "ingenic,x1000-mmc";
+		reg = <0x13450000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <37>;
+
+		clocks = <&cgu X1000_CLK_MSC0>;
+		clock-names = "mmc";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+
+		dmas = <&pdma X1000_DMA_MSC0_RX 0xffffffff>,
+			   <&pdma X1000_DMA_MSC0_TX 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		status = "disabled";
+	};
+
+	msc1: mmc@13460000 {
+		compatible = "ingenic,x1000-mmc";
+		reg = <0x13460000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <36>;
+
+		clocks = <&cgu X1000_CLK_MSC1>;
+		clock-names = "mmc";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+
+		dmas = <&pdma X1000_DMA_MSC1_RX 0xffffffff>,
+			   <&pdma X1000_DMA_MSC1_TX 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		status = "disabled";
+	};
+};
diff --git a/arch/mips/jz4740/Kconfig b/arch/mips/jz4740/Kconfig
index 4dd0c44..6b96844 100644
--- a/arch/mips/jz4740/Kconfig
+++ b/arch/mips/jz4740/Kconfig
@@ -33,3 +33,9 @@ config MACH_JZ4780
 	select MIPS_CPU_SCACHE
 	select SYS_HAS_CPU_MIPS32_R2
 	select SYS_SUPPORTS_HIGHMEM
+
+config MACH_X1000
+	bool
+	select MIPS_CPU_SCACHE
+	select SYS_HAS_CPU_MIPS32_R2
+	select SYS_SUPPORTS_HIGHMEM
-- 
2.7.4


^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH v8 2/4] dt-bindings: Document yna vendor-prefix.
  2019-12-10 12:02 Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v7 周琰杰 (Zhou Yanjie)
  2019-12-10 12:02 ` [PATCH v8 1/4] MIPS: Ingenic: Add Ingenic X1000 support 周琰杰 (Zhou Yanjie)
@ 2019-12-10 12:02 ` 周琰杰 (Zhou Yanjie)
  2019-12-18 14:54   ` Rob Herring
  2019-12-10 12:02 ` [PATCH v8 3/4] dt-bindings: MIPS: Add Ingenic XBurst based boards 周琰杰 (Zhou Yanjie)
  2019-12-10 12:02 ` [PATCH v8 4/4] MIPS: Ingenic: Add YSH & ATIL CU Neo board support 周琰杰 (Zhou Yanjie)
  3 siblings, 1 reply; 11+ messages in thread
From: 周琰杰 (Zhou Yanjie) @ 2019-12-10 12:02 UTC (permalink / raw)
  To: linux-mips
  Cc: linux-kernel, devicetree, robh+dt, paul.burton, paulburton,
	jhogan, mripard, shawnguo, mark.rutland, alexandre.belloni, ralf,
	heiko, icenowy, ak, laurent.pinchart, krzk, geert+renesas, paul,
	prasannatsmkumar, keescook, ebiederm, sernia.zhou, zhenwenjin,
	772753199

The "yna" is an acronym of the "YSH & ATIL".

Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
---

Notes:
    v1->v2:
    No change.
    
    v2->v3:
    No change.
    
    v3->v4:
    No change.
    
    v4->v5:
    No change.
    
    v5->v6:
    No change.
    
    v6->v7:
    Change my Signed-off-by from "Zhou Yanjie <zhouyanjie@zoho.com>"
    to "周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>" because
    the old mailbox is in an unstable state.
    
    v7->v8:
    No change.

 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 6046f45..50c2b63 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -1060,6 +1060,8 @@ patternProperties:
     description: Xilinx
   "^xunlong,.*":
     description: Shenzhen Xunlong Software CO.,Limited
+  "^yna,.*":
+    description: YSH & ATIL
   "^yones-toptech,.*":
     description: Yones Toptech Co., Ltd.
   "^ysoft,.*":
-- 
2.7.4


^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH v8 3/4] dt-bindings: MIPS: Add Ingenic XBurst based boards.
  2019-12-10 12:02 Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v7 周琰杰 (Zhou Yanjie)
  2019-12-10 12:02 ` [PATCH v8 1/4] MIPS: Ingenic: Add Ingenic X1000 support 周琰杰 (Zhou Yanjie)
  2019-12-10 12:02 ` [PATCH v8 2/4] dt-bindings: Document yna vendor-prefix 周琰杰 (Zhou Yanjie)
@ 2019-12-10 12:02 ` 周琰杰 (Zhou Yanjie)
  2019-12-18 14:55   ` Rob Herring
  2019-12-10 12:02 ` [PATCH v8 4/4] MIPS: Ingenic: Add YSH & ATIL CU Neo board support 周琰杰 (Zhou Yanjie)
  3 siblings, 1 reply; 11+ messages in thread
From: 周琰杰 (Zhou Yanjie) @ 2019-12-10 12:02 UTC (permalink / raw)
  To: linux-mips
  Cc: linux-kernel, devicetree, robh+dt, paul.burton, paulburton,
	jhogan, mripard, shawnguo, mark.rutland, alexandre.belloni, ralf,
	heiko, icenowy, ak, laurent.pinchart, krzk, geert+renesas, paul,
	prasannatsmkumar, keescook, ebiederm, sernia.zhou, zhenwenjin,
	772753199

Add Ingenic XBurst based boards, prepare for later dts.

Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
---

Notes:
    v1->v2:
    No change.
    
    v2->v3:
    No change.
    
    v3->v4:
    Adjust the description to make it more reasonable.
    
    v4->v5:
    Adjust item naming to prevent conflicts with
    subsequent "CU Geo" boards.
    
    v5->v6:
    No change.
    
    v6->v7:
    Change my Signed-off-by from "Zhou Yanjie <zhouyanjie@zoho.com>"
    to "周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>" because
    the old mailbox is in an unstable state.
    
    v7->v8:
    No change.

 .../devicetree/bindings/mips/ingenic/devices.yaml  | 35 ++++++++++++++++++++++
 1 file changed, 35 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mips/ingenic/devices.yaml

diff --git a/Documentation/devicetree/bindings/mips/ingenic/devices.yaml b/Documentation/devicetree/bindings/mips/ingenic/devices.yaml
new file mode 100644
index 00000000..78dcf6e
--- /dev/null
+++ b/Documentation/devicetree/bindings/mips/ingenic/devices.yaml
@@ -0,0 +1,35 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mips/ingenic/devices.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Ingenic XBurst based Platforms Device Tree Bindings
+
+maintainers:
+  - 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
+description: |
+  Devices with a Ingenic XBurst CPU shall have the following properties.
+
+properties:
+  $nodename:
+    const: '/'
+  compatible:
+    oneOf:
+
+      - description: Qi Hardware Ben NanoNote
+        items:
+          - const: qi,lb60
+
+      - description: Game Consoles Worldwide GCW Zero
+        items:
+          - const: gcw,zero
+
+      - description: MIPS Creator CI20
+        items:
+          - const: img,ci20
+
+      - description: YSH & ATIL General Board CU Neo
+        items:
+          - const: yna,cu1000-neo
+...
-- 
2.7.4


^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH v8 4/4] MIPS: Ingenic: Add YSH & ATIL CU Neo board support.
  2019-12-10 12:02 Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v7 周琰杰 (Zhou Yanjie)
                   ` (2 preceding siblings ...)
  2019-12-10 12:02 ` [PATCH v8 3/4] dt-bindings: MIPS: Add Ingenic XBurst based boards 周琰杰 (Zhou Yanjie)
@ 2019-12-10 12:02 ` 周琰杰 (Zhou Yanjie)
  2019-12-10 17:19   ` Paul Cercueil
  3 siblings, 1 reply; 11+ messages in thread
From: 周琰杰 (Zhou Yanjie) @ 2019-12-10 12:02 UTC (permalink / raw)
  To: linux-mips
  Cc: linux-kernel, devicetree, robh+dt, paul.burton, paulburton,
	jhogan, mripard, shawnguo, mark.rutland, alexandre.belloni, ralf,
	heiko, icenowy, ak, laurent.pinchart, krzk, geert+renesas, paul,
	prasannatsmkumar, keescook, ebiederm, sernia.zhou, zhenwenjin,
	772753199

Add a device tree for the Ingenic X1000 based YSH & ATIL CU Neo board.
Note that this is unselectable via Kconfig until the X1000 SoC is made
selectable in a later commit.

Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
---

Notes:
    v1->v2:
    Rebase on top of mips-next, use TCU for system timer and clocksource.
    
    v2->v3:
    No change.
    
    v3->v4:
    1.Adjust "model" in "cu1000.dts" to match the description in "devices.yaml".
    2.Adjust "bool" in "Kconfig" to avoid duplicate names with subsequent boards.
    
    v4->v5:
    1.Rename "cu1000" to "cu1000-neo" to prevent conflicts with subsequent boards
      such as "cu1000-geo", and so on.
    2.Remove "CONFIG_HZ=100" and "mem=32M@0x0" from defconfg.
    3.Modify incorrect comments in DT.
    
    v5->v6:
    1.Use "stdout-path = "serial2:115200n8"" instead "stdout-path = &uart2" in DT.
    2.Remove "console=ttyS2,115200n8" and "CONFIG_CMDLINE_OVERRIDE=y" from defconfg.
    
    v6->v7:
    Change my Signed-off-by from "Zhou Yanjie <zhouyanjie@zoho.com>"
    to "周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>" because
    the old mailbox is in an unstable state.
    
    v7->v8:
    Merge [6/6] in v7 to this patch.

 arch/mips/boot/dts/ingenic/Makefile       |   1 +
 arch/mips/boot/dts/ingenic/cu1000-neo.dts |  99 ++++++++++++++++++++++++++
 arch/mips/configs/cu1000-neo_defconfig    | 111 ++++++++++++++++++++++++++++++
 arch/mips/jz4740/Kconfig                  |   4 ++
 4 files changed, 215 insertions(+)
 create mode 100644 arch/mips/boot/dts/ingenic/cu1000-neo.dts
 create mode 100644 arch/mips/configs/cu1000-neo_defconfig

diff --git a/arch/mips/boot/dts/ingenic/Makefile b/arch/mips/boot/dts/ingenic/Makefile
index 9cc4844..e165429 100644
--- a/arch/mips/boot/dts/ingenic/Makefile
+++ b/arch/mips/boot/dts/ingenic/Makefile
@@ -2,5 +2,6 @@
 dtb-$(CONFIG_JZ4740_QI_LB60)	+= qi_lb60.dtb
 dtb-$(CONFIG_JZ4770_GCW0)	+= gcw0.dtb
 dtb-$(CONFIG_JZ4780_CI20)	+= ci20.dtb
+dtb-$(CONFIG_X1000_CU1000_NEO)	+= cu1000-neo.dtb
 
 obj-$(CONFIG_BUILTIN_DTB)	+= $(addsuffix .o, $(dtb-y))
diff --git a/arch/mips/boot/dts/ingenic/cu1000-neo.dts b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
new file mode 100644
index 00000000..b0733da
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
@@ -0,0 +1,99 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "x1000.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/ingenic,tcu.h>
+
+/ {
+	compatible = "yna,cu1000-neo", "ingenic,x1000";
+	model = "YSH & ATIL General Board CU Neo";
+
+	aliases {
+		serial2 = &uart2;
+	};
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x04000000>;
+	};
+};
+
+&exclk {
+	clock-frequency = <24000000>;
+};
+
+&tcu {
+	/* 1500 kHz for the system timer and clocksource */
+	assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER2>;
+	assigned-clock-rates = <1500000>, <1500000>;
+
+	/* Use channel #0 for the system timer channel #2 for the clocksource */
+	ingenic,pwm-channels-mask = <0xfa>;
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_uart2>;
+
+	status = "okay";
+};
+
+&mac {
+	phy-mode = "rmii";
+	phy-handle = <&lan8720a>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_mac>;
+
+	snps,reset-gpio = <&gpc 23 GPIO_ACTIVE_LOW>; /* PC23 */
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 30000>;
+
+	status = "okay";
+};
+
+&mdio {
+	status = "okay";
+
+	lan8720a: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0007.c0f0", "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&msc0 {
+	bus-width = <8>;
+	max-frequency = <50000000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_msc0>;
+
+	non-removable;
+
+	status = "okay";
+};
+
+&pinctrl {
+	pins_uart2: uart2 {
+		function = "uart2";
+		groups = "uart2-data-d";
+		bias-disable;
+	};
+
+	pins_mac: mac {
+		function = "mac";
+		groups = "mac";
+		bias-disable;
+	};
+
+	pins_msc0: msc0 {
+		function = "mmc0";
+		groups = "mmc0-1bit", "mmc0-4bit", "mmc0-8bit";
+		bias-disable;
+	};
+};
diff --git a/arch/mips/configs/cu1000-neo_defconfig b/arch/mips/configs/cu1000-neo_defconfig
new file mode 100644
index 00000000..9f988ed
--- /dev/null
+++ b/arch/mips/configs/cu1000-neo_defconfig
@@ -0,0 +1,111 @@
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_KERNEL_GZIP=y
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_CGROUPS=y
+CONFIG_MEMCG=y
+CONFIG_MEMCG_KMEM=y
+CONFIG_CGROUP_SCHED=y
+CONFIG_CGROUP_FREEZER=y
+CONFIG_CGROUP_DEVICE=y
+CONFIG_CGROUP_CPUACCT=y
+CONFIG_NAMESPACES=y
+CONFIG_USER_NS=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_EMBEDDED=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_MACH_INGENIC=y
+CONFIG_X1000_CU1000_NEO=y
+CONFIG_HIGHMEM=y
+CONFIG_HZ_100=y
+# CONFIG_SECCOMP is not set
+# CONFIG_SUSPEND is not set
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_COMPACTION is not set
+CONFIG_CMA=y
+CONFIG_CMA_AREAS=7
+CONFIG_NET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_UEVENT_HELPER=y
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_ALLOW_DEV_COREDUMP is not set
+CONFIG_NETDEVICES=y
+CONFIG_STMMAC_ETH=y
+CONFIG_SMSC_PHY=y
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_LEGACY_PTY_COUNT=2
+CONFIG_SERIAL_EARLYCON=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=3
+CONFIG_SERIAL_8250_RUNTIME_UARTS=3
+CONFIG_SERIAL_8250_INGENIC=y
+CONFIG_SERIAL_OF_PLATFORM=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_GPIO_SYSFS=y
+CONFIG_WATCHDOG=y
+CONFIG_JZ4740_WDT=y
+# CONFIG_HWMON is not set
+# CONFIG_LCD_CLASS_DEVICE is not set
+# CONFIG_BACKLIGHT_CLASS_DEVICE is not set
+# CONFIG_VGA_CONSOLE is not set
+# CONFIG_HID is not set
+# CONFIG_USB_SUPPORT is not set
+CONFIG_MMC=y
+CONFIG_MMC_JZ4740=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_JZ4740=y
+CONFIG_DMADEVICES=y
+CONFIG_DMA_JZ4780=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_NVMEM=y
+CONFIG_NVMEM_SYSFS=y
+CONFIG_EXT4_FS=y
+# CONFIG_DNOTIFY is not set
+CONFIG_AUTOFS_FS=y
+CONFIG_PROC_KCORE=y
+# CONFIG_PROC_PAGE_MONITOR is not set
+CONFIG_TMPFS=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_NLS=y
+CONFIG_NLS_CODEPAGE_936=y
+CONFIG_NLS_CODEPAGE_950=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+CONFIG_CRYPTO_ECHAINIV=y
+CONFIG_CRYPTO_AES=y
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_LZO=y
+CONFIG_PRINTK_TIME=y
+CONFIG_CONSOLE_LOGLEVEL_DEFAULT=15
+CONFIG_CONSOLE_LOGLEVEL_QUIET=15
+CONFIG_MESSAGE_LOGLEVEL_DEFAULT=7
+CONFIG_DEBUG_INFO=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_PANIC_ON_OOPS=y
+CONFIG_PANIC_TIMEOUT=10
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_PREEMPT is not set
+CONFIG_STACKTRACE=y
+# CONFIG_FTRACE is not set
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="earlycon clk_ignore_unused"
diff --git a/arch/mips/jz4740/Kconfig b/arch/mips/jz4740/Kconfig
index 6b96844..412d2fa 100644
--- a/arch/mips/jz4740/Kconfig
+++ b/arch/mips/jz4740/Kconfig
@@ -16,6 +16,10 @@ config JZ4780_CI20
 	bool "MIPS Creator CI20"
 	select MACH_JZ4780
 
+config X1000_CU1000_NEO
+	bool "YSH & ATIL CU1000 Module with Neo backplane"
+	select MACH_X1000
+
 endchoice
 
 config MACH_JZ4740
-- 
2.7.4


^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [PATCH v8 4/4] MIPS: Ingenic: Add YSH & ATIL CU Neo board support.
  2019-12-10 12:02 ` [PATCH v8 4/4] MIPS: Ingenic: Add YSH & ATIL CU Neo board support 周琰杰 (Zhou Yanjie)
@ 2019-12-10 17:19   ` Paul Cercueil
  2019-12-11 11:02     ` zhouyanjie
  0 siblings, 1 reply; 11+ messages in thread
From: Paul Cercueil @ 2019-12-10 17:19 UTC (permalink / raw)
  To: 周琰杰 (Zhou Yanjie)
  Cc: linux-mips, linux-kernel, devicetree, robh+dt, paul.burton,
	paulburton, jhogan, mripard, shawnguo, mark.rutland,
	alexandre.belloni, ralf, heiko, icenowy, ak, laurent.pinchart,
	krzk, geert+renesas, prasannatsmkumar, keescook, ebiederm,
	sernia.zhou, zhenwenjin, 772753199

Hi Zhou,


Le mar., déc. 10, 2019 at 20:02, 周琰杰 (Zhou Yanjie) 
<zhouyanjie@wanyeetech.com> a écrit :
> Add a device tree for the Ingenic X1000 based YSH & ATIL CU Neo board.
> Note that this is unselectable via Kconfig until the X1000 SoC is made
> selectable in a later commit.

I believe it is now selectable via Kconfig, right?

For the whole series:
Acked-by: Paul Cercueil <paul@crapouillou.net>

Cheers,
Paul


> Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
> ---
> 
> Notes:
>     v1->v2:
>     Rebase on top of mips-next, use TCU for system timer and 
> clocksource.
> 
>     v2->v3:
>     No change.
> 
>     v3->v4:
>     1.Adjust "model" in "cu1000.dts" to match the description in 
> "devices.yaml".
>     2.Adjust "bool" in "Kconfig" to avoid duplicate names with 
> subsequent boards.
> 
>     v4->v5:
>     1.Rename "cu1000" to "cu1000-neo" to prevent conflicts with 
> subsequent boards
>       such as "cu1000-geo", and so on.
>     2.Remove "CONFIG_HZ=100" and "mem=32M@0x0" from defconfg.
>     3.Modify incorrect comments in DT.
> 
>     v5->v6:
>     1.Use "stdout-path = "serial2:115200n8"" instead "stdout-path = 
> &uart2" in DT.
>     2.Remove "console=ttyS2,115200n8" and "CONFIG_CMDLINE_OVERRIDE=y" 
> from defconfg.
> 
>     v6->v7:
>     Change my Signed-off-by from "Zhou Yanjie <zhouyanjie@zoho.com>"
>     to "周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>" because
>     the old mailbox is in an unstable state.
> 
>     v7->v8:
>     Merge [6/6] in v7 to this patch.
> 
>  arch/mips/boot/dts/ingenic/Makefile       |   1 +
>  arch/mips/boot/dts/ingenic/cu1000-neo.dts |  99 
> ++++++++++++++++++++++++++
>  arch/mips/configs/cu1000-neo_defconfig    | 111 
> ++++++++++++++++++++++++++++++
>  arch/mips/jz4740/Kconfig                  |   4 ++
>  4 files changed, 215 insertions(+)
>  create mode 100644 arch/mips/boot/dts/ingenic/cu1000-neo.dts
>  create mode 100644 arch/mips/configs/cu1000-neo_defconfig
> 
> diff --git a/arch/mips/boot/dts/ingenic/Makefile 
> b/arch/mips/boot/dts/ingenic/Makefile
> index 9cc4844..e165429 100644
> --- a/arch/mips/boot/dts/ingenic/Makefile
> +++ b/arch/mips/boot/dts/ingenic/Makefile
> @@ -2,5 +2,6 @@
>  dtb-$(CONFIG_JZ4740_QI_LB60)	+= qi_lb60.dtb
>  dtb-$(CONFIG_JZ4770_GCW0)	+= gcw0.dtb
>  dtb-$(CONFIG_JZ4780_CI20)	+= ci20.dtb
> +dtb-$(CONFIG_X1000_CU1000_NEO)	+= cu1000-neo.dtb
> 
>  obj-$(CONFIG_BUILTIN_DTB)	+= $(addsuffix .o, $(dtb-y))
> diff --git a/arch/mips/boot/dts/ingenic/cu1000-neo.dts 
> b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
> new file mode 100644
> index 00000000..b0733da
> --- /dev/null
> +++ b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
> @@ -0,0 +1,99 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/dts-v1/;
> +
> +#include "x1000.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/clock/ingenic,tcu.h>
> +
> +/ {
> +	compatible = "yna,cu1000-neo", "ingenic,x1000";
> +	model = "YSH & ATIL General Board CU Neo";
> +
> +	aliases {
> +		serial2 = &uart2;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial2:115200n8";
> +	};
> +
> +	memory {
> +		device_type = "memory";
> +		reg = <0x0 0x04000000>;
> +	};
> +};
> +
> +&exclk {
> +	clock-frequency = <24000000>;
> +};
> +
> +&tcu {
> +	/* 1500 kHz for the system timer and clocksource */
> +	assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER2>;
> +	assigned-clock-rates = <1500000>, <1500000>;
> +
> +	/* Use channel #0 for the system timer channel #2 for the 
> clocksource */
> +	ingenic,pwm-channels-mask = <0xfa>;
> +};
> +
> +&uart2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pins_uart2>;
> +
> +	status = "okay";
> +};
> +
> +&mac {
> +	phy-mode = "rmii";
> +	phy-handle = <&lan8720a>;
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pins_mac>;
> +
> +	snps,reset-gpio = <&gpc 23 GPIO_ACTIVE_LOW>; /* PC23 */
> +	snps,reset-active-low;
> +	snps,reset-delays-us = <0 10000 30000>;
> +
> +	status = "okay";
> +};
> +
> +&mdio {
> +	status = "okay";
> +
> +	lan8720a: ethernet-phy@0 {
> +		compatible = "ethernet-phy-id0007.c0f0", 
> "ethernet-phy-ieee802.3-c22";
> +		reg = <0>;
> +	};
> +};
> +
> +&msc0 {
> +	bus-width = <8>;
> +	max-frequency = <50000000>;
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pins_msc0>;
> +
> +	non-removable;
> +
> +	status = "okay";
> +};
> +
> +&pinctrl {
> +	pins_uart2: uart2 {
> +		function = "uart2";
> +		groups = "uart2-data-d";
> +		bias-disable;
> +	};
> +
> +	pins_mac: mac {
> +		function = "mac";
> +		groups = "mac";
> +		bias-disable;
> +	};
> +
> +	pins_msc0: msc0 {
> +		function = "mmc0";
> +		groups = "mmc0-1bit", "mmc0-4bit", "mmc0-8bit";
> +		bias-disable;
> +	};
> +};
> diff --git a/arch/mips/configs/cu1000-neo_defconfig 
> b/arch/mips/configs/cu1000-neo_defconfig
> new file mode 100644
> index 00000000..9f988ed
> --- /dev/null
> +++ b/arch/mips/configs/cu1000-neo_defconfig
> @@ -0,0 +1,111 @@
> +CONFIG_LOCALVERSION_AUTO=y
> +CONFIG_KERNEL_GZIP=y
> +CONFIG_SYSVIPC=y
> +CONFIG_NO_HZ_IDLE=y
> +CONFIG_HIGH_RES_TIMERS=y
> +CONFIG_PREEMPT=y
> +CONFIG_IKCONFIG=y
> +CONFIG_IKCONFIG_PROC=y
> +CONFIG_LOG_BUF_SHIFT=14
> +CONFIG_CGROUPS=y
> +CONFIG_MEMCG=y
> +CONFIG_MEMCG_KMEM=y
> +CONFIG_CGROUP_SCHED=y
> +CONFIG_CGROUP_FREEZER=y
> +CONFIG_CGROUP_DEVICE=y
> +CONFIG_CGROUP_CPUACCT=y
> +CONFIG_NAMESPACES=y
> +CONFIG_USER_NS=y
> +CONFIG_CC_OPTIMIZE_FOR_SIZE=y
> +CONFIG_SYSCTL_SYSCALL=y
> +CONFIG_KALLSYMS_ALL=y
> +CONFIG_EMBEDDED=y
> +# CONFIG_VM_EVENT_COUNTERS is not set
> +# CONFIG_COMPAT_BRK is not set
> +CONFIG_SLAB=y
> +CONFIG_MACH_INGENIC=y
> +CONFIG_X1000_CU1000_NEO=y
> +CONFIG_HIGHMEM=y
> +CONFIG_HZ_100=y
> +# CONFIG_SECCOMP is not set
> +# CONFIG_SUSPEND is not set
> +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
> +# CONFIG_COMPACTION is not set
> +CONFIG_CMA=y
> +CONFIG_CMA_AREAS=7
> +CONFIG_NET=y
> +CONFIG_UNIX=y
> +CONFIG_INET=y
> +CONFIG_UEVENT_HELPER=y
> +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
> +CONFIG_DEVTMPFS=y
> +# CONFIG_FW_LOADER is not set
> +# CONFIG_ALLOW_DEV_COREDUMP is not set
> +CONFIG_NETDEVICES=y
> +CONFIG_STMMAC_ETH=y
> +CONFIG_SMSC_PHY=y
> +# CONFIG_INPUT_MOUSEDEV is not set
> +# CONFIG_INPUT_KEYBOARD is not set
> +# CONFIG_INPUT_MOUSE is not set
> +# CONFIG_SERIO is not set
> +CONFIG_VT_HW_CONSOLE_BINDING=y
> +CONFIG_LEGACY_PTY_COUNT=2
> +CONFIG_SERIAL_EARLYCON=y
> +CONFIG_SERIAL_8250=y
> +CONFIG_SERIAL_8250_CONSOLE=y
> +CONFIG_SERIAL_8250_NR_UARTS=3
> +CONFIG_SERIAL_8250_RUNTIME_UARTS=3
> +CONFIG_SERIAL_8250_INGENIC=y
> +CONFIG_SERIAL_OF_PLATFORM=y
> +# CONFIG_HW_RANDOM is not set
> +CONFIG_GPIO_SYSFS=y
> +CONFIG_WATCHDOG=y
> +CONFIG_JZ4740_WDT=y
> +# CONFIG_HWMON is not set
> +# CONFIG_LCD_CLASS_DEVICE is not set
> +# CONFIG_BACKLIGHT_CLASS_DEVICE is not set
> +# CONFIG_VGA_CONSOLE is not set
> +# CONFIG_HID is not set
> +# CONFIG_USB_SUPPORT is not set
> +CONFIG_MMC=y
> +CONFIG_MMC_JZ4740=y
> +CONFIG_RTC_CLASS=y
> +CONFIG_RTC_DRV_JZ4740=y
> +CONFIG_DMADEVICES=y
> +CONFIG_DMA_JZ4780=y
> +# CONFIG_IOMMU_SUPPORT is not set
> +CONFIG_NVMEM=y
> +CONFIG_NVMEM_SYSFS=y
> +CONFIG_EXT4_FS=y
> +# CONFIG_DNOTIFY is not set
> +CONFIG_AUTOFS_FS=y
> +CONFIG_PROC_KCORE=y
> +# CONFIG_PROC_PAGE_MONITOR is not set
> +CONFIG_TMPFS=y
> +CONFIG_CONFIGFS_FS=y
> +CONFIG_NLS=y
> +CONFIG_NLS_CODEPAGE_936=y
> +CONFIG_NLS_CODEPAGE_950=y
> +CONFIG_NLS_ASCII=y
> +CONFIG_NLS_ISO8859_1=y
> +CONFIG_NLS_UTF8=y
> +CONFIG_CRYPTO_ECHAINIV=y
> +CONFIG_CRYPTO_AES=y
> +CONFIG_CRYPTO_DEFLATE=y
> +CONFIG_CRYPTO_LZO=y
> +CONFIG_PRINTK_TIME=y
> +CONFIG_CONSOLE_LOGLEVEL_DEFAULT=15
> +CONFIG_CONSOLE_LOGLEVEL_QUIET=15
> +CONFIG_MESSAGE_LOGLEVEL_DEFAULT=7
> +CONFIG_DEBUG_INFO=y
> +CONFIG_STRIP_ASM_SYMS=y
> +CONFIG_DEBUG_FS=y
> +CONFIG_MAGIC_SYSRQ=y
> +CONFIG_PANIC_ON_OOPS=y
> +CONFIG_PANIC_TIMEOUT=10
> +# CONFIG_SCHED_DEBUG is not set
> +# CONFIG_DEBUG_PREEMPT is not set
> +CONFIG_STACKTRACE=y
> +# CONFIG_FTRACE is not set
> +CONFIG_CMDLINE_BOOL=y
> +CONFIG_CMDLINE="earlycon clk_ignore_unused"
> diff --git a/arch/mips/jz4740/Kconfig b/arch/mips/jz4740/Kconfig
> index 6b96844..412d2fa 100644
> --- a/arch/mips/jz4740/Kconfig
> +++ b/arch/mips/jz4740/Kconfig
> @@ -16,6 +16,10 @@ config JZ4780_CI20
>  	bool "MIPS Creator CI20"
>  	select MACH_JZ4780
> 
> +config X1000_CU1000_NEO
> +	bool "YSH & ATIL CU1000 Module with Neo backplane"
> +	select MACH_X1000
> +
>  endchoice
> 
>  config MACH_JZ4740
> --
> 2.7.4
> 



^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [PATCH v8 4/4] MIPS: Ingenic: Add YSH & ATIL CU Neo board support.
  2019-12-10 17:19   ` Paul Cercueil
@ 2019-12-11 11:02     ` zhouyanjie
  2019-12-11 12:56       ` Paul Cercueil
  0 siblings, 1 reply; 11+ messages in thread
From: zhouyanjie @ 2019-12-11 11:02 UTC (permalink / raw)
  To: Paul Cercueil
  Cc: linux-mips, linux-kernel, devicetree, robh+dt, paul.burton,
	paulburton, jhogan, mripard, shawnguo, mark.rutland,
	alexandre.belloni, ralf, heiko, icenowy, ak, laurent.pinchart,
	krzk, geert+renesas, prasannatsmkumar, keescook, ebiederm,
	sernia.zhou, zhenwenjin, 772753199



On 2019年12月11日 01:19, Paul Cercueil wrote:
> Hi Zhou,
>
>
> Le mar., déc. 10, 2019 at 20:02, 周琰杰 (Zhou Yanjie) 
> <zhouyanjie@wanyeetech.com> a écrit :
>> Add a device tree for the Ingenic X1000 based YSH & ATIL CU Neo board.
>> Note that this is unselectable via Kconfig until the X1000 SoC is made
>> selectable in a later commit.
>
> I believe it is now selectable via Kconfig, right?
>

Oh, apologize for my careless, it should be selectable now.
Do I need to send a v9 to fix the commit message?

Thanks and best regards!

> For the whole series:
> Acked-by: Paul Cercueil <paul@crapouillou.net>
>
> Cheers,
> Paul
>
>
>> Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
>> ---
>>
>> Notes:
>>     v1->v2:
>>     Rebase on top of mips-next, use TCU for system timer and 
>> clocksource.
>>
>>     v2->v3:
>>     No change.
>>
>>     v3->v4:
>>     1.Adjust "model" in "cu1000.dts" to match the description in 
>> "devices.yaml".
>>     2.Adjust "bool" in "Kconfig" to avoid duplicate names with 
>> subsequent boards.
>>
>>     v4->v5:
>>     1.Rename "cu1000" to "cu1000-neo" to prevent conflicts with 
>> subsequent boards
>>       such as "cu1000-geo", and so on.
>>     2.Remove "CONFIG_HZ=100" and "mem=32M@0x0" from defconfg.
>>     3.Modify incorrect comments in DT.
>>
>>     v5->v6:
>>     1.Use "stdout-path = "serial2:115200n8"" instead "stdout-path = 
>> &uart2" in DT.
>>     2.Remove "console=ttyS2,115200n8" and "CONFIG_CMDLINE_OVERRIDE=y" 
>> from defconfg.
>>
>>     v6->v7:
>>     Change my Signed-off-by from "Zhou Yanjie <zhouyanjie@zoho.com>"
>>     to "周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>" because
>>     the old mailbox is in an unstable state.
>>
>>     v7->v8:
>>     Merge [6/6] in v7 to this patch.
>>
>>  arch/mips/boot/dts/ingenic/Makefile       |   1 +
>>  arch/mips/boot/dts/ingenic/cu1000-neo.dts |  99 
>> ++++++++++++++++++++++++++
>>  arch/mips/configs/cu1000-neo_defconfig    | 111 
>> ++++++++++++++++++++++++++++++
>>  arch/mips/jz4740/Kconfig                  |   4 ++
>>  4 files changed, 215 insertions(+)
>>  create mode 100644 arch/mips/boot/dts/ingenic/cu1000-neo.dts
>>  create mode 100644 arch/mips/configs/cu1000-neo_defconfig
>>
>> diff --git a/arch/mips/boot/dts/ingenic/Makefile 
>> b/arch/mips/boot/dts/ingenic/Makefile
>> index 9cc4844..e165429 100644
>> --- a/arch/mips/boot/dts/ingenic/Makefile
>> +++ b/arch/mips/boot/dts/ingenic/Makefile
>> @@ -2,5 +2,6 @@
>>  dtb-$(CONFIG_JZ4740_QI_LB60)    += qi_lb60.dtb
>>  dtb-$(CONFIG_JZ4770_GCW0)    += gcw0.dtb
>>  dtb-$(CONFIG_JZ4780_CI20)    += ci20.dtb
>> +dtb-$(CONFIG_X1000_CU1000_NEO)    += cu1000-neo.dtb
>>
>>  obj-$(CONFIG_BUILTIN_DTB)    += $(addsuffix .o, $(dtb-y))
>> diff --git a/arch/mips/boot/dts/ingenic/cu1000-neo.dts 
>> b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
>> new file mode 100644
>> index 00000000..b0733da
>> --- /dev/null
>> +++ b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
>> @@ -0,0 +1,99 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/dts-v1/;
>> +
>> +#include "x1000.dtsi"
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/clock/ingenic,tcu.h>
>> +
>> +/ {
>> +    compatible = "yna,cu1000-neo", "ingenic,x1000";
>> +    model = "YSH & ATIL General Board CU Neo";
>> +
>> +    aliases {
>> +        serial2 = &uart2;
>> +    };
>> +
>> +    chosen {
>> +        stdout-path = "serial2:115200n8";
>> +    };
>> +
>> +    memory {
>> +        device_type = "memory";
>> +        reg = <0x0 0x04000000>;
>> +    };
>> +};
>> +
>> +&exclk {
>> +    clock-frequency = <24000000>;
>> +};
>> +
>> +&tcu {
>> +    /* 1500 kHz for the system timer and clocksource */
>> +    assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER2>;
>> +    assigned-clock-rates = <1500000>, <1500000>;
>> +
>> +    /* Use channel #0 for the system timer channel #2 for the 
>> clocksource */
>> +    ingenic,pwm-channels-mask = <0xfa>;
>> +};
>> +
>> +&uart2 {
>> +    pinctrl-names = "default";
>> +    pinctrl-0 = <&pins_uart2>;
>> +
>> +    status = "okay";
>> +};
>> +
>> +&mac {
>> +    phy-mode = "rmii";
>> +    phy-handle = <&lan8720a>;
>> +
>> +    pinctrl-names = "default";
>> +    pinctrl-0 = <&pins_mac>;
>> +
>> +    snps,reset-gpio = <&gpc 23 GPIO_ACTIVE_LOW>; /* PC23 */
>> +    snps,reset-active-low;
>> +    snps,reset-delays-us = <0 10000 30000>;
>> +
>> +    status = "okay";
>> +};
>> +
>> +&mdio {
>> +    status = "okay";
>> +
>> +    lan8720a: ethernet-phy@0 {
>> +        compatible = "ethernet-phy-id0007.c0f0", 
>> "ethernet-phy-ieee802.3-c22";
>> +        reg = <0>;
>> +    };
>> +};
>> +
>> +&msc0 {
>> +    bus-width = <8>;
>> +    max-frequency = <50000000>;
>> +
>> +    pinctrl-names = "default";
>> +    pinctrl-0 = <&pins_msc0>;
>> +
>> +    non-removable;
>> +
>> +    status = "okay";
>> +};
>> +
>> +&pinctrl {
>> +    pins_uart2: uart2 {
>> +        function = "uart2";
>> +        groups = "uart2-data-d";
>> +        bias-disable;
>> +    };
>> +
>> +    pins_mac: mac {
>> +        function = "mac";
>> +        groups = "mac";
>> +        bias-disable;
>> +    };
>> +
>> +    pins_msc0: msc0 {
>> +        function = "mmc0";
>> +        groups = "mmc0-1bit", "mmc0-4bit", "mmc0-8bit";
>> +        bias-disable;
>> +    };
>> +};
>> diff --git a/arch/mips/configs/cu1000-neo_defconfig 
>> b/arch/mips/configs/cu1000-neo_defconfig
>> new file mode 100644
>> index 00000000..9f988ed
>> --- /dev/null
>> +++ b/arch/mips/configs/cu1000-neo_defconfig
>> @@ -0,0 +1,111 @@
>> +CONFIG_LOCALVERSION_AUTO=y
>> +CONFIG_KERNEL_GZIP=y
>> +CONFIG_SYSVIPC=y
>> +CONFIG_NO_HZ_IDLE=y
>> +CONFIG_HIGH_RES_TIMERS=y
>> +CONFIG_PREEMPT=y
>> +CONFIG_IKCONFIG=y
>> +CONFIG_IKCONFIG_PROC=y
>> +CONFIG_LOG_BUF_SHIFT=14
>> +CONFIG_CGROUPS=y
>> +CONFIG_MEMCG=y
>> +CONFIG_MEMCG_KMEM=y
>> +CONFIG_CGROUP_SCHED=y
>> +CONFIG_CGROUP_FREEZER=y
>> +CONFIG_CGROUP_DEVICE=y
>> +CONFIG_CGROUP_CPUACCT=y
>> +CONFIG_NAMESPACES=y
>> +CONFIG_USER_NS=y
>> +CONFIG_CC_OPTIMIZE_FOR_SIZE=y
>> +CONFIG_SYSCTL_SYSCALL=y
>> +CONFIG_KALLSYMS_ALL=y
>> +CONFIG_EMBEDDED=y
>> +# CONFIG_VM_EVENT_COUNTERS is not set
>> +# CONFIG_COMPAT_BRK is not set
>> +CONFIG_SLAB=y
>> +CONFIG_MACH_INGENIC=y
>> +CONFIG_X1000_CU1000_NEO=y
>> +CONFIG_HIGHMEM=y
>> +CONFIG_HZ_100=y
>> +# CONFIG_SECCOMP is not set
>> +# CONFIG_SUSPEND is not set
>> +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
>> +# CONFIG_COMPACTION is not set
>> +CONFIG_CMA=y
>> +CONFIG_CMA_AREAS=7
>> +CONFIG_NET=y
>> +CONFIG_UNIX=y
>> +CONFIG_INET=y
>> +CONFIG_UEVENT_HELPER=y
>> +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
>> +CONFIG_DEVTMPFS=y
>> +# CONFIG_FW_LOADER is not set
>> +# CONFIG_ALLOW_DEV_COREDUMP is not set
>> +CONFIG_NETDEVICES=y
>> +CONFIG_STMMAC_ETH=y
>> +CONFIG_SMSC_PHY=y
>> +# CONFIG_INPUT_MOUSEDEV is not set
>> +# CONFIG_INPUT_KEYBOARD is not set
>> +# CONFIG_INPUT_MOUSE is not set
>> +# CONFIG_SERIO is not set
>> +CONFIG_VT_HW_CONSOLE_BINDING=y
>> +CONFIG_LEGACY_PTY_COUNT=2
>> +CONFIG_SERIAL_EARLYCON=y
>> +CONFIG_SERIAL_8250=y
>> +CONFIG_SERIAL_8250_CONSOLE=y
>> +CONFIG_SERIAL_8250_NR_UARTS=3
>> +CONFIG_SERIAL_8250_RUNTIME_UARTS=3
>> +CONFIG_SERIAL_8250_INGENIC=y
>> +CONFIG_SERIAL_OF_PLATFORM=y
>> +# CONFIG_HW_RANDOM is not set
>> +CONFIG_GPIO_SYSFS=y
>> +CONFIG_WATCHDOG=y
>> +CONFIG_JZ4740_WDT=y
>> +# CONFIG_HWMON is not set
>> +# CONFIG_LCD_CLASS_DEVICE is not set
>> +# CONFIG_BACKLIGHT_CLASS_DEVICE is not set
>> +# CONFIG_VGA_CONSOLE is not set
>> +# CONFIG_HID is not set
>> +# CONFIG_USB_SUPPORT is not set
>> +CONFIG_MMC=y
>> +CONFIG_MMC_JZ4740=y
>> +CONFIG_RTC_CLASS=y
>> +CONFIG_RTC_DRV_JZ4740=y
>> +CONFIG_DMADEVICES=y
>> +CONFIG_DMA_JZ4780=y
>> +# CONFIG_IOMMU_SUPPORT is not set
>> +CONFIG_NVMEM=y
>> +CONFIG_NVMEM_SYSFS=y
>> +CONFIG_EXT4_FS=y
>> +# CONFIG_DNOTIFY is not set
>> +CONFIG_AUTOFS_FS=y
>> +CONFIG_PROC_KCORE=y
>> +# CONFIG_PROC_PAGE_MONITOR is not set
>> +CONFIG_TMPFS=y
>> +CONFIG_CONFIGFS_FS=y
>> +CONFIG_NLS=y
>> +CONFIG_NLS_CODEPAGE_936=y
>> +CONFIG_NLS_CODEPAGE_950=y
>> +CONFIG_NLS_ASCII=y
>> +CONFIG_NLS_ISO8859_1=y
>> +CONFIG_NLS_UTF8=y
>> +CONFIG_CRYPTO_ECHAINIV=y
>> +CONFIG_CRYPTO_AES=y
>> +CONFIG_CRYPTO_DEFLATE=y
>> +CONFIG_CRYPTO_LZO=y
>> +CONFIG_PRINTK_TIME=y
>> +CONFIG_CONSOLE_LOGLEVEL_DEFAULT=15
>> +CONFIG_CONSOLE_LOGLEVEL_QUIET=15
>> +CONFIG_MESSAGE_LOGLEVEL_DEFAULT=7
>> +CONFIG_DEBUG_INFO=y
>> +CONFIG_STRIP_ASM_SYMS=y
>> +CONFIG_DEBUG_FS=y
>> +CONFIG_MAGIC_SYSRQ=y
>> +CONFIG_PANIC_ON_OOPS=y
>> +CONFIG_PANIC_TIMEOUT=10
>> +# CONFIG_SCHED_DEBUG is not set
>> +# CONFIG_DEBUG_PREEMPT is not set
>> +CONFIG_STACKTRACE=y
>> +# CONFIG_FTRACE is not set
>> +CONFIG_CMDLINE_BOOL=y
>> +CONFIG_CMDLINE="earlycon clk_ignore_unused"
>> diff --git a/arch/mips/jz4740/Kconfig b/arch/mips/jz4740/Kconfig
>> index 6b96844..412d2fa 100644
>> --- a/arch/mips/jz4740/Kconfig
>> +++ b/arch/mips/jz4740/Kconfig
>> @@ -16,6 +16,10 @@ config JZ4780_CI20
>>      bool "MIPS Creator CI20"
>>      select MACH_JZ4780
>>
>> +config X1000_CU1000_NEO
>> +    bool "YSH & ATIL CU1000 Module with Neo backplane"
>> +    select MACH_X1000
>> +
>>  endchoice
>>
>>  config MACH_JZ4740
>> -- 
>> 2.7.4
>>
>


^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [PATCH v8 4/4] MIPS: Ingenic: Add YSH & ATIL CU Neo board support.
  2019-12-11 11:02     ` zhouyanjie
@ 2019-12-11 12:56       ` Paul Cercueil
  0 siblings, 0 replies; 11+ messages in thread
From: Paul Cercueil @ 2019-12-11 12:56 UTC (permalink / raw)
  To: zhouyanjie
  Cc: linux-mips, linux-kernel, devicetree, robh+dt, paul.burton,
	paulburton, jhogan, mripard, shawnguo, mark.rutland,
	alexandre.belloni, ralf, heiko, icenowy, ak, laurent.pinchart,
	krzk, geert+renesas, prasannatsmkumar, keescook, ebiederm,
	sernia.zhou, zhenwenjin, 772753199

Hi Zhou,


Le mer., déc. 11, 2019 at 19:02, zhouyanjie 
<zhouyanjie@wanyeetech.com> a écrit :
> 
> 
> On 2019年12月11日 01:19, Paul Cercueil wrote:
>> Hi Zhou,
>> 
>> 
>> Le mar., déc. 10, 2019 at 20:02, 周琰杰 (Zhou Yanjie) 
>> \x7f<zhouyanjie@wanyeetech.com> a écrit :
>>> Add a device tree for the Ingenic X1000 based YSH & ATIL CU Neo 
>>> board.
>>> Note that this is unselectable via Kconfig until the X1000 SoC is 
>>> made
>>> selectable in a later commit.
>> 
>> I believe it is now selectable via Kconfig, right?
>> 
> 
> Oh, apologize for my careless, it should be selectable now.
> Do I need to send a v9 to fix the commit message?

Maybe Paul Burton can just remove the last sentence when merging.

-Paul


>> For the whole series:
>> Acked-by: Paul Cercueil <paul@crapouillou.net>
>> 
>> Cheers,
>> Paul
>> 
>> 
>>> Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
>>> ---
>>> 
>>> Notes:
>>>     v1->v2:
>>>     Rebase on top of mips-next, use TCU for system timer and 
>>> \x7f\x7fclocksource.
>>> 
>>>     v2->v3:
>>>     No change.
>>> 
>>>     v3->v4:
>>>     1.Adjust "model" in "cu1000.dts" to match the description in 
>>> \x7f\x7f"devices.yaml".
>>>     2.Adjust "bool" in "Kconfig" to avoid duplicate names with 
>>> \x7f\x7fsubsequent boards.
>>> 
>>>     v4->v5:
>>>     1.Rename "cu1000" to "cu1000-neo" to prevent conflicts with 
>>> \x7f\x7fsubsequent boards
>>>       such as "cu1000-geo", and so on.
>>>     2.Remove "CONFIG_HZ=100" and "mem=32M@0x0" from defconfg.
>>>     3.Modify incorrect comments in DT.
>>> 
>>>     v5->v6:
>>>     1.Use "stdout-path = "serial2:115200n8"" instead "stdout-path = 
>>> \x7f\x7f&uart2" in DT.
>>>     2.Remove "console=ttyS2,115200n8" and 
>>> "CONFIG_CMDLINE_OVERRIDE=y" \x7f\x7ffrom defconfg.
>>> 
>>>     v6->v7:
>>>     Change my Signed-off-by from "Zhou Yanjie <zhouyanjie@zoho.com>"
>>>     to "周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>" because
>>>     the old mailbox is in an unstable state.
>>> 
>>>     v7->v8:
>>>     Merge [6/6] in v7 to this patch.
>>> 
>>>  arch/mips/boot/dts/ingenic/Makefile       |   1 +
>>>  arch/mips/boot/dts/ingenic/cu1000-neo.dts |  99 
>>> \x7f\x7f++++++++++++++++++++++++++
>>>  arch/mips/configs/cu1000-neo_defconfig    | 111 
>>> \x7f\x7f++++++++++++++++++++++++++++++
>>>  arch/mips/jz4740/Kconfig                  |   4 ++
>>>  4 files changed, 215 insertions(+)
>>>  create mode 100644 arch/mips/boot/dts/ingenic/cu1000-neo.dts
>>>  create mode 100644 arch/mips/configs/cu1000-neo_defconfig
>>> 
>>> diff --git a/arch/mips/boot/dts/ingenic/Makefile 
>>> \x7f\x7fb/arch/mips/boot/dts/ingenic/Makefile
>>> index 9cc4844..e165429 100644
>>> --- a/arch/mips/boot/dts/ingenic/Makefile
>>> +++ b/arch/mips/boot/dts/ingenic/Makefile
>>> @@ -2,5 +2,6 @@
>>>  dtb-$(CONFIG_JZ4740_QI_LB60)    += qi_lb60.dtb
>>>  dtb-$(CONFIG_JZ4770_GCW0)    += gcw0.dtb
>>>  dtb-$(CONFIG_JZ4780_CI20)    += ci20.dtb
>>> +dtb-$(CONFIG_X1000_CU1000_NEO)    += cu1000-neo.dtb
>>> 
>>>  obj-$(CONFIG_BUILTIN_DTB)    += $(addsuffix .o, $(dtb-y))
>>> diff --git a/arch/mips/boot/dts/ingenic/cu1000-neo.dts 
>>> \x7f\x7fb/arch/mips/boot/dts/ingenic/cu1000-neo.dts
>>> new file mode 100644
>>> index 00000000..b0733da
>>> --- /dev/null
>>> +++ b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
>>> @@ -0,0 +1,99 @@
>>> +// SPDX-License-Identifier: GPL-2.0
>>> +/dts-v1/;
>>> +
>>> +#include "x1000.dtsi"
>>> +#include <dt-bindings/gpio/gpio.h>
>>> +#include <dt-bindings/clock/ingenic,tcu.h>
>>> +
>>> +/ {
>>> +    compatible = "yna,cu1000-neo", "ingenic,x1000";
>>> +    model = "YSH & ATIL General Board CU Neo";
>>> +
>>> +    aliases {
>>> +        serial2 = &uart2;
>>> +    };
>>> +
>>> +    chosen {
>>> +        stdout-path = "serial2:115200n8";
>>> +    };
>>> +
>>> +    memory {
>>> +        device_type = "memory";
>>> +        reg = <0x0 0x04000000>;
>>> +    };
>>> +};
>>> +
>>> +&exclk {
>>> +    clock-frequency = <24000000>;
>>> +};
>>> +
>>> +&tcu {
>>> +    /* 1500 kHz for the system timer and clocksource */
>>> +    assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER2>;
>>> +    assigned-clock-rates = <1500000>, <1500000>;
>>> +
>>> +    /* Use channel #0 for the system timer channel #2 for the 
>>> \x7f\x7fclocksource */
>>> +    ingenic,pwm-channels-mask = <0xfa>;
>>> +};
>>> +
>>> +&uart2 {
>>> +    pinctrl-names = "default";
>>> +    pinctrl-0 = <&pins_uart2>;
>>> +
>>> +    status = "okay";
>>> +};
>>> +
>>> +&mac {
>>> +    phy-mode = "rmii";
>>> +    phy-handle = <&lan8720a>;
>>> +
>>> +    pinctrl-names = "default";
>>> +    pinctrl-0 = <&pins_mac>;
>>> +
>>> +    snps,reset-gpio = <&gpc 23 GPIO_ACTIVE_LOW>; /* PC23 */
>>> +    snps,reset-active-low;
>>> +    snps,reset-delays-us = <0 10000 30000>;
>>> +
>>> +    status = "okay";
>>> +};
>>> +
>>> +&mdio {
>>> +    status = "okay";
>>> +
>>> +    lan8720a: ethernet-phy@0 {
>>> +        compatible = "ethernet-phy-id0007.c0f0", 
>>> \x7f\x7f"ethernet-phy-ieee802.3-c22";
>>> +        reg = <0>;
>>> +    };
>>> +};
>>> +
>>> +&msc0 {
>>> +    bus-width = <8>;
>>> +    max-frequency = <50000000>;
>>> +
>>> +    pinctrl-names = "default";
>>> +    pinctrl-0 = <&pins_msc0>;
>>> +
>>> +    non-removable;
>>> +
>>> +    status = "okay";
>>> +};
>>> +
>>> +&pinctrl {
>>> +    pins_uart2: uart2 {
>>> +        function = "uart2";
>>> +        groups = "uart2-data-d";
>>> +        bias-disable;
>>> +    };
>>> +
>>> +    pins_mac: mac {
>>> +        function = "mac";
>>> +        groups = "mac";
>>> +        bias-disable;
>>> +    };
>>> +
>>> +    pins_msc0: msc0 {
>>> +        function = "mmc0";
>>> +        groups = "mmc0-1bit", "mmc0-4bit", "mmc0-8bit";
>>> +        bias-disable;
>>> +    };
>>> +};
>>> diff --git a/arch/mips/configs/cu1000-neo_defconfig 
>>> \x7f\x7fb/arch/mips/configs/cu1000-neo_defconfig
>>> new file mode 100644
>>> index 00000000..9f988ed
>>> --- /dev/null
>>> +++ b/arch/mips/configs/cu1000-neo_defconfig
>>> @@ -0,0 +1,111 @@
>>> +CONFIG_LOCALVERSION_AUTO=y
>>> +CONFIG_KERNEL_GZIP=y
>>> +CONFIG_SYSVIPC=y
>>> +CONFIG_NO_HZ_IDLE=y
>>> +CONFIG_HIGH_RES_TIMERS=y
>>> +CONFIG_PREEMPT=y
>>> +CONFIG_IKCONFIG=y
>>> +CONFIG_IKCONFIG_PROC=y
>>> +CONFIG_LOG_BUF_SHIFT=14
>>> +CONFIG_CGROUPS=y
>>> +CONFIG_MEMCG=y
>>> +CONFIG_MEMCG_KMEM=y
>>> +CONFIG_CGROUP_SCHED=y
>>> +CONFIG_CGROUP_FREEZER=y
>>> +CONFIG_CGROUP_DEVICE=y
>>> +CONFIG_CGROUP_CPUACCT=y
>>> +CONFIG_NAMESPACES=y
>>> +CONFIG_USER_NS=y
>>> +CONFIG_CC_OPTIMIZE_FOR_SIZE=y
>>> +CONFIG_SYSCTL_SYSCALL=y
>>> +CONFIG_KALLSYMS_ALL=y
>>> +CONFIG_EMBEDDED=y
>>> +# CONFIG_VM_EVENT_COUNTERS is not set
>>> +# CONFIG_COMPAT_BRK is not set
>>> +CONFIG_SLAB=y
>>> +CONFIG_MACH_INGENIC=y
>>> +CONFIG_X1000_CU1000_NEO=y
>>> +CONFIG_HIGHMEM=y
>>> +CONFIG_HZ_100=y
>>> +# CONFIG_SECCOMP is not set
>>> +# CONFIG_SUSPEND is not set
>>> +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
>>> +# CONFIG_COMPACTION is not set
>>> +CONFIG_CMA=y
>>> +CONFIG_CMA_AREAS=7
>>> +CONFIG_NET=y
>>> +CONFIG_UNIX=y
>>> +CONFIG_INET=y
>>> +CONFIG_UEVENT_HELPER=y
>>> +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
>>> +CONFIG_DEVTMPFS=y
>>> +# CONFIG_FW_LOADER is not set
>>> +# CONFIG_ALLOW_DEV_COREDUMP is not set
>>> +CONFIG_NETDEVICES=y
>>> +CONFIG_STMMAC_ETH=y
>>> +CONFIG_SMSC_PHY=y
>>> +# CONFIG_INPUT_MOUSEDEV is not set
>>> +# CONFIG_INPUT_KEYBOARD is not set
>>> +# CONFIG_INPUT_MOUSE is not set
>>> +# CONFIG_SERIO is not set
>>> +CONFIG_VT_HW_CONSOLE_BINDING=y
>>> +CONFIG_LEGACY_PTY_COUNT=2
>>> +CONFIG_SERIAL_EARLYCON=y
>>> +CONFIG_SERIAL_8250=y
>>> +CONFIG_SERIAL_8250_CONSOLE=y
>>> +CONFIG_SERIAL_8250_NR_UARTS=3
>>> +CONFIG_SERIAL_8250_RUNTIME_UARTS=3
>>> +CONFIG_SERIAL_8250_INGENIC=y
>>> +CONFIG_SERIAL_OF_PLATFORM=y
>>> +# CONFIG_HW_RANDOM is not set
>>> +CONFIG_GPIO_SYSFS=y
>>> +CONFIG_WATCHDOG=y
>>> +CONFIG_JZ4740_WDT=y
>>> +# CONFIG_HWMON is not set
>>> +# CONFIG_LCD_CLASS_DEVICE is not set
>>> +# CONFIG_BACKLIGHT_CLASS_DEVICE is not set
>>> +# CONFIG_VGA_CONSOLE is not set
>>> +# CONFIG_HID is not set
>>> +# CONFIG_USB_SUPPORT is not set
>>> +CONFIG_MMC=y
>>> +CONFIG_MMC_JZ4740=y
>>> +CONFIG_RTC_CLASS=y
>>> +CONFIG_RTC_DRV_JZ4740=y
>>> +CONFIG_DMADEVICES=y
>>> +CONFIG_DMA_JZ4780=y
>>> +# CONFIG_IOMMU_SUPPORT is not set
>>> +CONFIG_NVMEM=y
>>> +CONFIG_NVMEM_SYSFS=y
>>> +CONFIG_EXT4_FS=y
>>> +# CONFIG_DNOTIFY is not set
>>> +CONFIG_AUTOFS_FS=y
>>> +CONFIG_PROC_KCORE=y
>>> +# CONFIG_PROC_PAGE_MONITOR is not set
>>> +CONFIG_TMPFS=y
>>> +CONFIG_CONFIGFS_FS=y
>>> +CONFIG_NLS=y
>>> +CONFIG_NLS_CODEPAGE_936=y
>>> +CONFIG_NLS_CODEPAGE_950=y
>>> +CONFIG_NLS_ASCII=y
>>> +CONFIG_NLS_ISO8859_1=y
>>> +CONFIG_NLS_UTF8=y
>>> +CONFIG_CRYPTO_ECHAINIV=y
>>> +CONFIG_CRYPTO_AES=y
>>> +CONFIG_CRYPTO_DEFLATE=y
>>> +CONFIG_CRYPTO_LZO=y
>>> +CONFIG_PRINTK_TIME=y
>>> +CONFIG_CONSOLE_LOGLEVEL_DEFAULT=15
>>> +CONFIG_CONSOLE_LOGLEVEL_QUIET=15
>>> +CONFIG_MESSAGE_LOGLEVEL_DEFAULT=7
>>> +CONFIG_DEBUG_INFO=y
>>> +CONFIG_STRIP_ASM_SYMS=y
>>> +CONFIG_DEBUG_FS=y
>>> +CONFIG_MAGIC_SYSRQ=y
>>> +CONFIG_PANIC_ON_OOPS=y
>>> +CONFIG_PANIC_TIMEOUT=10
>>> +# CONFIG_SCHED_DEBUG is not set
>>> +# CONFIG_DEBUG_PREEMPT is not set
>>> +CONFIG_STACKTRACE=y
>>> +# CONFIG_FTRACE is not set
>>> +CONFIG_CMDLINE_BOOL=y
>>> +CONFIG_CMDLINE="earlycon clk_ignore_unused"
>>> diff --git a/arch/mips/jz4740/Kconfig b/arch/mips/jz4740/Kconfig
>>> index 6b96844..412d2fa 100644
>>> --- a/arch/mips/jz4740/Kconfig
>>> +++ b/arch/mips/jz4740/Kconfig
>>> @@ -16,6 +16,10 @@ config JZ4780_CI20
>>>      bool "MIPS Creator CI20"
>>>      select MACH_JZ4780
>>> 
>>> +config X1000_CU1000_NEO
>>> +    bool "YSH & ATIL CU1000 Module with Neo backplane"
>>> +    select MACH_X1000
>>> +
>>>  endchoice
>>> 
>>>  config MACH_JZ4740
>>> --
>>> 2.7.4
>>> 
>> 
> 



^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [PATCH v8 2/4] dt-bindings: Document yna vendor-prefix.
  2019-12-10 12:02 ` [PATCH v8 2/4] dt-bindings: Document yna vendor-prefix 周琰杰 (Zhou Yanjie)
@ 2019-12-18 14:54   ` Rob Herring
  0 siblings, 0 replies; 11+ messages in thread
From: Rob Herring @ 2019-12-18 14:54 UTC (permalink / raw)
  To: 周琰杰 (Zhou Yanjie)
  Cc: linux-mips, linux-kernel, devicetree, robh+dt, paul.burton,
	paulburton, jhogan, mripard, shawnguo, mark.rutland,
	alexandre.belloni, ralf, heiko, icenowy, ak, laurent.pinchart,
	krzk, geert+renesas, paul, prasannatsmkumar, keescook, ebiederm,
	sernia.zhou, zhenwenjin, 772753199

On Tue, 10 Dec 2019 20:02:41 +0800, =?UTF-8?q?=E5=91=A8=E7=90=B0=E6=9D=B0=20=28Zhou=20Yanjie=29?=          wrote:
> The "yna" is an acronym of the "YSH & ATIL".
> 
> Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
> ---
> 
> Notes:
>     v1->v2:
>     No change.
>     
>     v2->v3:
>     No change.
>     
>     v3->v4:
>     No change.
>     
>     v4->v5:
>     No change.
>     
>     v5->v6:
>     No change.
>     
>     v6->v7:
>     Change my Signed-off-by from "Zhou Yanjie <zhouyanjie@zoho.com>"
>     to "周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>" because
>     the old mailbox is in an unstable state.
>     
>     v7->v8:
>     No change.
> 
>  Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
>  1 file changed, 2 insertions(+)
> 

Acked-by: Rob Herring <robh@kernel.org>

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [PATCH v8 3/4] dt-bindings: MIPS: Add Ingenic XBurst based boards.
  2019-12-10 12:02 ` [PATCH v8 3/4] dt-bindings: MIPS: Add Ingenic XBurst based boards 周琰杰 (Zhou Yanjie)
@ 2019-12-18 14:55   ` Rob Herring
  0 siblings, 0 replies; 11+ messages in thread
From: Rob Herring @ 2019-12-18 14:55 UTC (permalink / raw)
  To: 周琰杰 (Zhou Yanjie)
  Cc: linux-mips, linux-kernel, devicetree, robh+dt, paul.burton,
	paulburton, jhogan, mripard, shawnguo, mark.rutland,
	alexandre.belloni, ralf, heiko, icenowy, ak, laurent.pinchart,
	krzk, geert+renesas, paul, prasannatsmkumar, keescook, ebiederm,
	sernia.zhou, zhenwenjin, 772753199

On Tue, 10 Dec 2019 20:02:42 +0800, =?UTF-8?q?=E5=91=A8=E7=90=B0=E6=9D=B0=20=28Zhou=20Yanjie=29?=          wrote:
> Add Ingenic XBurst based boards, prepare for later dts.
> 
> Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
> ---
> 
> Notes:
>     v1->v2:
>     No change.
>     
>     v2->v3:
>     No change.
>     
>     v3->v4:
>     Adjust the description to make it more reasonable.
>     
>     v4->v5:
>     Adjust item naming to prevent conflicts with
>     subsequent "CU Geo" boards.
>     
>     v5->v6:
>     No change.
>     
>     v6->v7:
>     Change my Signed-off-by from "Zhou Yanjie <zhouyanjie@zoho.com>"
>     to "周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>" because
>     the old mailbox is in an unstable state.
>     
>     v7->v8:
>     No change.
> 
>  .../devicetree/bindings/mips/ingenic/devices.yaml  | 35 ++++++++++++++++++++++
>  1 file changed, 35 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mips/ingenic/devices.yaml
> 

Reviewed-by: Rob Herring <robh@kernel.org>

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [PATCH v8 1/4] MIPS: Ingenic: Add Ingenic X1000 support.
  2019-12-10 12:02 ` [PATCH v8 1/4] MIPS: Ingenic: Add Ingenic X1000 support 周琰杰 (Zhou Yanjie)
@ 2020-01-09 18:52   ` Paul Burton
  0 siblings, 0 replies; 11+ messages in thread
From: Paul Burton @ 2020-01-09 18:52 UTC (permalink / raw)
  To: 周琰杰 (Zhou Yanjie)
  Cc: linux-mips, linux-kernel, devicetree, robh+dt, paul.burton,
	paulburton, jhogan, mripard, shawnguo, mark.rutland,
	alexandre.belloni, ralf, heiko, icenowy, ak, laurent.pinchart,
	krzk, geert+renesas, paul, prasannatsmkumar, keescook, ebiederm,
	sernia.zhou, zhenwenjin, 772753199, linux-mips

[-- Warning: decoded text below may be mangled --]
[-- Attachment #0: Type: text/plain, Size: 1635 bytes --]

Hello,

周琰杰 (Zhou Yanjie) wrote:
> Support the Ingenic X1000 SoC using the code under arch/mips/jz4740.
> This is left unselectable in Kconfig until a X1000 based board is
> added in a later commit.

Series applied to mips-next.

> MIPS: Ingenic: Add Ingenic X1000 support.
>   commit 7a16ccd300c2
>   https://git.kernel.org/mips/c/7a16ccd300c2
>   
>   Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
>   Signed-off-by: Paul Burton <paulburton@kernel.org>
> 
> dt-bindings: Document yna vendor-prefix.
>   commit 9d022be3c192
>   https://git.kernel.org/mips/c/9d022be3c192
>   
>   Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
>   Acked-by: Rob Herring <robh@kernel.org>
>   Signed-off-by: Paul Burton <paulburton@kernel.org>
> 
> dt-bindings: MIPS: Add Ingenic XBurst based boards.
>   commit 4b396e56a0b8
>   https://git.kernel.org/mips/c/4b396e56a0b8
>   
>   Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
>   Reviewed-by: Rob Herring <robh@kernel.org>
>   Signed-off-by: Paul Burton <paulburton@kernel.org>
> 
> MIPS: Ingenic: Add YSH & ATIL CU Neo board support.
>   commit 0cd2c6e5701e
>   https://git.kernel.org/mips/c/0cd2c6e5701e
>   
>   Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
>   Acked-by: Paul Cercueil <paul@crapouillou.net>
>   [paulburton@kernel.org:
>     Drop stale mention of previously unselectable Kconfig entry.]
>   Signed-off-by: Paul Burton <paulburton@kernel.org>

Thanks,
    Paul

[ This message was auto-generated; if you believe anything is incorrect
  then please email paulburton@kernel.org to report it. ]

^ permalink raw reply	[flat|nested] 11+ messages in thread

end of thread, back to index

Thread overview: 11+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-12-10 12:02 Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v7 周琰杰 (Zhou Yanjie)
2019-12-10 12:02 ` [PATCH v8 1/4] MIPS: Ingenic: Add Ingenic X1000 support 周琰杰 (Zhou Yanjie)
2020-01-09 18:52   ` Paul Burton
2019-12-10 12:02 ` [PATCH v8 2/4] dt-bindings: Document yna vendor-prefix 周琰杰 (Zhou Yanjie)
2019-12-18 14:54   ` Rob Herring
2019-12-10 12:02 ` [PATCH v8 3/4] dt-bindings: MIPS: Add Ingenic XBurst based boards 周琰杰 (Zhou Yanjie)
2019-12-18 14:55   ` Rob Herring
2019-12-10 12:02 ` [PATCH v8 4/4] MIPS: Ingenic: Add YSH & ATIL CU Neo board support 周琰杰 (Zhou Yanjie)
2019-12-10 17:19   ` Paul Cercueil
2019-12-11 11:02     ` zhouyanjie
2019-12-11 12:56       ` Paul Cercueil

Linux-MIPS Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-mips/0 linux-mips/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-mips linux-mips/ https://lore.kernel.org/linux-mips \
		linux-mips@vger.kernel.org
	public-inbox-index linux-mips

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-mips


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git