Linux-mtd Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH 0/5] mtd: rawnand: qcom: Add support for QSPI nand
@ 2020-10-10  5:31 Md Sadre Alam
  2020-10-10  5:31 ` [PATCH 1/5] dt-bindings: qcom_nandc: IPQ5018 QPIC NAND documentation Md Sadre Alam
                   ` (5 more replies)
  0 siblings, 6 replies; 13+ messages in thread
From: Md Sadre Alam @ 2020-10-10  5:31 UTC (permalink / raw)
  To: agross, bjorn.andersson, miquel.raynal, richard, vigneshr,
	robh+dt, linux-arm-msm, linux-mtd, devicetree, linux-kernel
  Cc: mdalam, sricharan

QPIC 2.0 supports Serial NAND support in addition to all features and
commands in QPIC 1.0 for parallel NAND. Parallel and Serial NAND cannot
operate simultaneously. QSPI nand devices will connect to QPIC IO_MACRO
block of QPIC controller. There is a separate IO_MACRO clock for IO_MACRO
block. Default IO_MACRO block divide the input clock by 4. so if IO_MACRO
input clock is 320MHz then on bus it will be 80MHz, so QSPI nand device
should also support this frequency.

QPIC provides 4 data pins to QSPI nand. In standard SPI mode (x1 mode) data
transfer will occur on only 2 pins one pin for Serial data in and one for
serial data out. In QUAD SPI mode (x4 mode) data transfer will occur at all
the four data lines. QPIC controller supports command for x1 mode and x4 mode.

Md Sadre Alam (5):
  dt-bindings: qcom_nandc: IPQ5018 QPIC NAND documentation
  mtd: rawnand: qcom: Add initial support for qspi nand
  mtd: rawnand: qcom: Read QPIC version
  mtd: rawnand: qcom: Enable support for erase,read & write for serial
    nand.
  mtd: rawnand: qcom: Add support for serial training.

 .../devicetree/bindings/mtd/qcom_nandc.txt         |   3 +
 drivers/mtd/nand/raw/nand_ids.c                    |  13 +
 drivers/mtd/nand/raw/qcom_nandc.c                  | 502 ++++++++++++++++++++-
 3 files changed, 494 insertions(+), 24 deletions(-)

-- 
2.7.4


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 13+ messages in thread

end of thread, back to index

Thread overview: 13+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-10-10  5:31 [PATCH 0/5] mtd: rawnand: qcom: Add support for QSPI nand Md Sadre Alam
2020-10-10  5:31 ` [PATCH 1/5] dt-bindings: qcom_nandc: IPQ5018 QPIC NAND documentation Md Sadre Alam
2020-10-13 16:21   ` Rob Herring
2020-10-10  5:31 ` [PATCH 2/5] mtd: rawnand: qcom: Add initial support for qspi nand Md Sadre Alam
2020-10-29  9:07   ` Boris Brezillon
2020-10-10  5:31 ` [PATCH 3/5] mtd: rawnand: qcom: Read QPIC version Md Sadre Alam
2020-10-10  5:31 ` [PATCH 4/5] mtd: rawnand: qcom: Enable support for erase, read & write for serial nand Md Sadre Alam
2020-10-10  5:31 ` [PATCH 5/5] mtd: rawnand: qcom: Add support for serial training Md Sadre Alam
2020-10-28  9:48 ` [PATCH 0/5] mtd: rawnand: qcom: Add support for QSPI nand Miquel Raynal
2020-10-28 18:24   ` mdalam
2020-10-29  7:53     ` Miquel Raynal
2020-10-29  8:37       ` Miquel Raynal
2020-10-29  8:38       ` Boris Brezillon

Linux-mtd Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-mtd/0 linux-mtd/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-mtd linux-mtd/ https://lore.kernel.org/linux-mtd \
		linux-mtd@lists.infradead.org
	public-inbox-index linux-mtd

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.infradead.lists.linux-mtd


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git