[PATCH v5 11/12] arm64: dts: qcom: sm8550: Add PCIe PHYs and controllers nodes

[Abel Vesa <abel.vesa@linaro.org>]

Add PCIe controllers and PHY nodes.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---

This patch does not have a v3, but since it is now part of the same
patchset with the controller and the phy drivers patches, I had to
bump the version to 4.

The v4 was here:
https://lore.kernel.org/all/20230119140453.3942340-12-abel.vesa@linaro.org/

Changes since v4:
 * renamed noc_aggr_4 back to noc_aggr
 * moved pinctrl properties out to MTP dts
 * renamed nocsr to nocsr_com

Changes since v2:
 * renamed the pcie_1_link_down_reset to simply link_down
 * dropped the pipe from clock-names
 * renamed aggre clock-names to noc_aggr_4
 * dropped the _pcie infix from cnoc_pcie_sf_axi
 * dropped the aux_phy clock from the pcie1

Changes since v1:
 * ordered pcie related nodes alphabetically in MTP dts
 * dropped the pipe_mux, phy_pipe and ref clocks from the pcie nodes
 * dropped the child node from the phy nodes, like Johan suggested,
   and updated to use the sc8280xp binding scheme
 * changed "pcie_1_nocsr_com_phy_reset" 2nd reset name of pcie1_phy
   to "nocsr"
 * reordered all pcie nodes properties to look similar to the ones
   from sc8280xp


 arch/arm64/boot/dts/qcom/sm8550.dtsi | 203 ++++++++++++++++++++++++++-
 1 file changed, 200 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
index 3d47281a276b..4daf1f03d79f 100644
--- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
@@ -646,9 +646,9 @@ gcc: clock-controller@100000 {
 			#reset-cells = <1>;
 			#power-domain-cells = <1>;
 			clocks = <&bi_tcxo_div2>, <&sleep_clk>,
-				 <0>,
-				 <0>,
-				 <0>,
+				 <&pcie0_phy>,
+				 <&pcie1_phy>,
+				 <&pcie_1_phy_aux_clk>,
 				 <&ufs_mem_phy 0>,
 				 <&ufs_mem_phy 1>,
 				 <&ufs_mem_phy 2>,
@@ -1547,6 +1547,203 @@ mmss_noc: interconnect@1780000 {
 			qcom,bcm-voters = <&apps_bcm_voter>;
 		};
 
+		pcie0: pci@1c00000 {
+			device_type = "pci";
+			compatible = "qcom,pcie-sm8550";
+			reg = <0 0x01c00000 0 0x3000>,
+			      <0 0x60000000 0 0xf1d>,
+			      <0 0x60000f20 0 0xa8>,
+			      <0 0x60001000 0 0x1000>,
+			      <0 0x60100000 0 0x100000>;
+			reg-names = "parf", "dbi", "elbi", "atu", "config";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges = <0x01000000 0x0 0x60200000 0 0x60200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x60300000 0 0x60300000 0x0 0x3d00000>;
+			bus-range = <0x00 0xff>;
+
+			dma-coherent;
+
+			linux,pci-domain = <0>;
+			num-lanes = <2>;
+
+			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 0 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 0 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 0 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
+				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_DDRSS_PCIE_SF_QTB_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_AXI_CLK>;
+			clock-names = "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "ddrss_sf_tbu",
+				      "noc_aggr";
+
+			interconnects = <&pcie_noc MASTER_PCIE_0 0 &mc_virt SLAVE_EBI1 0>,
+					<&gem_noc MASTER_APPSS_PROC 0 &cnoc_main SLAVE_PCIE_0 0>;
+			interconnect-names = "pcie-mem", "cpu-pcie";
+
+			iommus = <&apps_smmu 0x1400 0x7f>;
+			iommu-map = <0x0   &apps_smmu 0x1400 0x1>,
+				    <0x100 &apps_smmu 0x1401 0x1>;
+
+			resets = <&gcc GCC_PCIE_0_BCR>;
+			reset-names = "pci";
+
+			power-domains = <&gcc PCIE_0_GDSC>;
+
+			phys = <&pcie0_phy>;
+			phy-names = "pciephy";
+
+			perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+			wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+
+			status = "disabled";
+		};
+
+		pcie0_phy: phy@1c06000 {
+			compatible = "qcom,sm8550-qmp-gen3x2-pcie-phy";
+			reg = <0 0x01c06000 0 0x2000>;
+
+			clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
+				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+				 <&tcsr TCSR_PCIE_0_CLKREF_EN>,
+				 <&gcc GCC_PCIE_0_PHY_RCHNG_CLK>,
+				 <&gcc GCC_PCIE_0_PIPE_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref", "rchng",
+				      "pipe";
+
+			resets = <&gcc GCC_PCIE_0_PHY_BCR>;
+			reset-names = "phy";
+
+			assigned-clocks = <&gcc GCC_PCIE_0_PHY_RCHNG_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			power-domains = <&gcc PCIE_0_PHY_GDSC>;
+
+			#clock-cells = <0>;
+			clock-output-names = "pcie0_pipe_clk";
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		pcie1: pci@1c08000 {
+			device_type = "pci";
+			compatible = "qcom,pcie-sm8550";
+			reg = <0x0 0x01c08000 0x0 0x3000>,
+			      <0x0 0x40000000 0x0 0xf1d>,
+			      <0x0 0x40000f20 0x0 0xa8>,
+			      <0x0 0x40001000 0x0 0x1000>,
+			      <0x0 0x40100000 0x0 0x100000>;
+			reg-names = "parf", "dbi", "elbi", "atu", "config";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges = <0x01000000 0x0 0x40200000 0 0x40200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x40300000 0 0x40300000 0x0 0x1fd00000>;
+			bus-range = <0x00 0xff>;
+
+			dma-coherent;
+
+			linux,pci-domain = <1>;
+			num-lanes = <2>;
+
+			interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 0 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 0 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 0 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE_1_AUX_CLK>,
+				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_DDRSS_PCIE_SF_QTB_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_AXI_CLK>,
+				 <&gcc GCC_CNOC_PCIE_SF_AXI_CLK>;
+			clock-names = "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "ddrss_sf_tbu",
+				      "noc_aggr",
+				      "cnoc_sf_axi";
+
+			assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>;
+			assigned-clock-rates = <19200000>;
+
+			interconnects = <&pcie_noc MASTER_PCIE_1 0 &mc_virt SLAVE_EBI1 0>,
+					<&gem_noc MASTER_APPSS_PROC 0 &cnoc_main SLAVE_PCIE_1 0>;
+			interconnect-names = "pcie-mem", "cpu-pcie";
+
+			iommus = <&apps_smmu 0x1480 0x7f>;
+			iommu-map = <0x0   &apps_smmu 0x1480 0x1>,
+				    <0x100 &apps_smmu 0x1481 0x1>;
+
+			resets = <&gcc GCC_PCIE_1_BCR>,
+				<&gcc GCC_PCIE_1_LINK_DOWN_BCR>;
+			reset-names = "pci", "link_down";
+
+			power-domains = <&gcc PCIE_1_GDSC>;
+
+			phys = <&pcie1_phy>;
+			phy-names = "pciephy";
+
+			perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
+			enable-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+
+			status = "disabled";
+		};
+
+		pcie1_phy: phy@1c0e000 {
+			compatible = "qcom,sm8550-qmp-gen4x2-pcie-phy";
+			reg = <0x0 0x01c0e000 0x0 0x2000>;
+
+			clocks = <&gcc GCC_PCIE_1_PHY_AUX_CLK>,
+				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+				 <&tcsr TCSR_PCIE_1_CLKREF_EN>,
+				 <&gcc GCC_PCIE_1_PHY_RCHNG_CLK>,
+				 <&gcc GCC_PCIE_1_PIPE_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref", "rchng",
+				      "pipe";
+
+			resets = <&gcc GCC_PCIE_1_PHY_BCR>,
+				 <&gcc GCC_PCIE_1_NOCSR_COM_PHY_BCR>;
+			reset-names = "phy", "nocsr_com";
+
+			assigned-clocks = <&gcc GCC_PCIE_1_PHY_RCHNG_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			power-domains = <&gcc PCIE_1_PHY_GDSC>;
+
+			#clock-cells = <0>;
+			clock-output-names = "pcie1_pipe_clk";
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
 		cryptobam: dma-controller@1dc4000 {
 			compatible = "qcom,bam-v1.7.0";
 			reg = <0x0 0x01dc4000 0x0 0x28000>;
-- 
2.34.1