From: "Kuppuswamy, Sathyanarayanan" <sathyanarayanan.kuppuswamy@linux.intel.com>
To: 20200714230803.GA92891@bjorn-Precision-5520, bhelgaas@google.com
Cc: linux-pci@vger.kernel.org, linux-kernel@vger.kernel.org,
ashok.raj@intel.com, Jay Vosburgh <jay.vosburgh@canonical.com>
Subject: Re: [PATCH v3 1/1] PCI/ERR: Fix reset logic in pcie_do_recovery() call
Date: Mon, 31 Aug 2020 22:41:40 -0700 [thread overview]
Message-ID: <56ad4901-725f-7b88-2117-b124b28b027f@linux.intel.com> (raw)
In-Reply-To: <cbba08a5e9ca62778c8937f44eda2192a2045da7.1595617529.git.sathyanarayanan.kuppuswamy@linux.intel.com>
Hi Bjorn,
On 7/24/20 12:07 PM, sathyanarayanan.kuppuswamy@linux.intel.com wrote:
> From: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
>
> Current pcie_do_recovery() implementation has following two issues:
>
> 1. Fatal (DPC) error recovery is currently broken for non-hotplug
> capable devices. Current fatal error recovery implementation relies
> on PCIe hotplug (pciehp) handler for detaching and re-enumerating
> the affected devices/drivers. pciehp handler listens for DLLSC state
> changes and handles device/driver detachment on DLLSC_LINK_DOWN event
> and re-enumeration on DLLSC_LINK_UP event. So when dealing with
> non-hotplug capable devices, recovery code does not restore the state
> of the affected devices correctly. Correct implementation should
> restore the device state and call report_slot_reset() function after
> resetting the link to restore the state of the device/driver.
>
> You can find fatal non-hotplug related issues reported in following links:
>
> https://lore.kernel.org/linux-pci/20200527083130.4137-1-Zhiqiang.Hou@nxp.com/
> https://lore.kernel.org/linux-pci/12115.1588207324@famine/
> https://lore.kernel.org/linux-pci/0e6f89cd6b9e4a72293cc90fafe93487d7c2d295.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com/
>
> 2. For non-fatal errors if report_error_detected() or
> report_mmio_enabled() functions requests PCI_ERS_RESULT_NEED_RESET then
> current pcie_do_recovery() implementation does not do the requested
> explicit device reset, instead just calls the report_slot_reset() on all
> affected devices. Notifying about the reset via report_slot_reset()
> without doing the actual device reset is incorrect.
>
> To fix above issues, use PCI_ERS_RESULT_NEED_RESET as error state after
> successful reset_link() operation. This will ensure ->slot_reset() be
> called after reset_link() operation for fatal errors. Also call
> pci_bus_reset() to do slot/bus reset() before triggering device specific
> ->slot_reset() callback. Also, using pci_bus_reset() will restore the state
> of the devices after performing the reset operation.
>
> Even though using pci_bus_reset() will do redundant reset operation after
> ->reset_link() for fatal errors, it should should affect the functional
> behavior.
Any comment on this patch?
>
> [original patch is from jay.vosburgh@canonical.com]
> [original patch link https://lore.kernel.org/linux-pci/12115.1588207324@famine/]
> Fixes: 6d2c89441571 ("PCI/ERR: Update error status after reset_link()")
> Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
> Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
> ---
>
> Changes since v2:
> * Changed the subject of patch to "PCI/ERR: Fix reset logic in
> pcie_do_recovery() call". v2 patch link is,
> https://lore.kernel.org/linux-pci/ce417fbf81a8a46a89535f44b9224ee9fbb55a29.1591307288.git.sathyanarayanan.kuppuswamy@linux.intel.com/
> * Squashed "PCI/ERR: Add reset support for non fatal errors" patch.
>
> drivers/pci/pcie/err.c | 41 +++++++++++++++++++++++++++++++++++++----
> 1 file changed, 37 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/pci/pcie/err.c b/drivers/pci/pcie/err.c
> index 14bb8f54723e..b5eb6ba65be1 100644
> --- a/drivers/pci/pcie/err.c
> +++ b/drivers/pci/pcie/err.c
> @@ -165,8 +165,29 @@ pci_ers_result_t pcie_do_recovery(struct pci_dev *dev,
> pci_dbg(dev, "broadcast error_detected message\n");
> if (state == pci_channel_io_frozen) {
> pci_walk_bus(bus, report_frozen_detected, &status);
> + /*
> + * After resetting the link using reset_link() call, the
> + * possible value of error status is either
> + * PCI_ERS_RESULT_DISCONNECT (failure case) or
> + * PCI_ERS_RESULT_NEED_RESET (success case).
> + * So ignore the return value of report_error_detected()
> + * call for fatal errors.
> + *
> + * In EDR mode, since AER and DPC Capabilities are owned by
> + * firmware, reported_error_detected() will return error
> + * status PCI_ERS_RESULT_NO_AER_DRIVER. Continuing
> + * pcie_do_recovery() with error status as
> + * PCI_ERS_RESULT_NO_AER_DRIVER will report recovery failure
> + * irrespective of recovery status. But successful reset_link()
> + * call usually recovers all fatal errors. So ignoring the
> + * status result of report_error_detected() also helps EDR based
> + * error recovery.
> + */
> status = reset_link(dev);
> - if (status != PCI_ERS_RESULT_RECOVERED) {
> + if (status == PCI_ERS_RESULT_RECOVERED) {
> + status = PCI_ERS_RESULT_NEED_RESET;
> + } else {
> + status = PCI_ERS_RESULT_DISCONNECT;
> pci_warn(dev, "link reset failed\n");
> goto failed;
> }
> @@ -182,10 +203,22 @@ pci_ers_result_t pcie_do_recovery(struct pci_dev *dev,
>
> if (status == PCI_ERS_RESULT_NEED_RESET) {
> /*
> - * TODO: Should call platform-specific
> - * functions to reset slot before calling
> - * drivers' slot_reset callbacks?
> + * TODO: Optimize the call to pci_reset_bus()
> + *
> + * There are two components to pci_reset_bus().
> + *
> + * 1. Do platform specific slot/bus reset.
> + * 2. Save/Restore all devices in the bus.
> + *
> + * For hotplug capable devices and fatal errors,
> + * device is already in reset state due to link
> + * reset. So repeating platform specific slot/bus
> + * reset via pci_reset_bus() call is redundant. So
> + * can optimize this logic and conditionally call
> + * pci_reset_bus().
> */
> + pci_reset_bus(dev);
> +
> status = PCI_ERS_RESULT_RECOVERED;
> pci_dbg(dev, "broadcast slot_reset message\n");
> pci_walk_bus(bus, report_slot_reset, &status);
>
--
Sathyanarayanan Kuppuswamy
Linux Kernel Developer
next prev parent reply other threads:[~2020-09-01 5:41 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-07-24 19:07 [PATCH v3 1/1] PCI/ERR: Fix reset logic in pcie_do_recovery() call sathyanarayanan.kuppuswamy
2020-09-01 5:41 ` Kuppuswamy, Sathyanarayanan [this message]
2020-09-22 18:52 ` Bjorn Helgaas
[not found] <3cad1a07-509b-ef51-f635-71def2ff8293@linux.intel.com>
2020-09-22 23:33 ` Bjorn Helgaas
2020-09-22 23:44 ` Kuppuswamy, Sathyanarayanan
2020-09-24 1:15 ` Sinan Kaya
2020-09-24 2:04 ` Kuppuswamy, Sathyanarayanan
2020-09-24 2:16 ` Sinan Kaya
2020-09-24 2:51 ` Kuppuswamy, Sathyanarayanan
2020-09-24 3:13 ` Sinan Kaya
2020-09-24 4:06 ` Kuppuswamy, Sathyanarayanan
2020-09-24 20:52 ` Sinan Kaya
2020-09-25 5:11 ` Kuppuswamy, Sathyanarayanan
2020-09-25 16:55 ` Sinan Kaya
2020-09-25 17:11 ` Kuppuswamy, Sathyanarayanan
2020-09-25 17:47 ` Sinan Kaya
2020-09-25 18:16 ` Kuppuswamy, Sathyanarayanan
2020-09-25 18:30 ` Sinan Kaya
2020-09-28 2:43 ` Kuppuswamy, Sathyanarayanan
2020-09-28 8:41 ` Ethan Zhao
2020-09-28 11:17 ` Sinan Kaya
2020-09-28 12:16 ` Sinan Kaya
2020-09-28 17:15 ` Kuppuswamy, Sathyanarayanan
2020-09-28 18:02 ` Sinan Kaya
2020-09-28 18:25 ` Sinan Kaya
2020-09-28 18:32 ` Kuppuswamy, Sathyanarayanan
2020-10-12 5:13 ` Kuppuswamy, Sathyanarayanan
2020-10-12 14:51 ` Sinan Kaya
2020-09-28 12:11 ` Sinan Kaya
2020-09-25 23:50 ` Sinan Kaya
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=56ad4901-725f-7b88-2117-b124b28b027f@linux.intel.com \
--to=sathyanarayanan.kuppuswamy@linux.intel.com \
--cc=20200714230803.GA92891@bjorn-Precision-5520 \
--cc=ashok.raj@intel.com \
--cc=bhelgaas@google.com \
--cc=jay.vosburgh@canonical.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).