* [PATCH v3 01/16] dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and R-CCU
2020-07-08 7:19 [PATCH v3 00/16] Allwinner A100 Initial support Frank Lee
@ 2020-07-08 7:19 ` Frank Lee
2020-07-13 22:54 ` Rob Herring
2020-07-08 7:19 ` [PATCH v3 02/16] clk: sunxi-ng: add support for the Allwinner A100 CCU Frank Lee
` (10 subsequent siblings)
11 siblings, 1 reply; 26+ messages in thread
From: Frank Lee @ 2020-07-08 7:19 UTC (permalink / raw)
To: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, clabbe, icenowy, megous, stefan, bage
Cc: devicetree, linux-arm-kernel, linux-kernel, linux-clk, linux-i2c,
linux-gpio, linux-pm, huangshuosheng, liyong, Frank Lee
This patch adds binding to a100's ccu clock and r-ccu clock.
Signed-off-by: Frank Lee <frank@allwinnertech.com>
---
.../devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml b/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml
index 4d38212..3b45344 100644
--- a/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml
+++ b/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml
@@ -36,6 +36,8 @@ properties:
- allwinner,sun9i-a80-ccu
- allwinner,sun50i-a64-ccu
- allwinner,sun50i-a64-r-ccu
+ - allwinner,sun50i-a100-ccu
+ - allwinner,sun50i-a100-r-ccu
- allwinner,sun50i-h5-ccu
- allwinner,sun50i-h6-ccu
- allwinner,sun50i-h6-r-ccu
@@ -78,6 +80,7 @@ if:
- allwinner,sun8i-a83t-r-ccu
- allwinner,sun8i-h3-r-ccu
- allwinner,sun50i-a64-r-ccu
+ - allwinner,sun50i-a100-r-ccu
- allwinner,sun50i-h6-r-ccu
then:
@@ -94,7 +97,9 @@ else:
if:
properties:
compatible:
- const: allwinner,sun50i-h6-ccu
+ enum:
+ - allwinner,sun50i-a100-ccu
+ - allwinner,sun50i-h6-ccu
then:
properties:
--
1.9.1
^ permalink raw reply related [flat|nested] 26+ messages in thread* Re: [PATCH v3 01/16] dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and R-CCU
2020-07-08 7:19 ` [PATCH v3 01/16] dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and R-CCU Frank Lee
@ 2020-07-13 22:54 ` Rob Herring
2020-07-13 23:33 ` Rob Herring
0 siblings, 1 reply; 26+ messages in thread
From: Rob Herring @ 2020-07-13 22:54 UTC (permalink / raw)
To: Frank Lee
Cc: mturquette, linus.walleij, clabbe, liyong, srinivas.kandagatla,
icenowy, p.zabel, linux-i2c, gregory.clement, sboyd,
amit.kucheria, bage, tglx, linux-pm, daniel.lezcano, anarsoul,
megous, tiny.windzz, lee.jones, rui.zhang, linux-clk, devicetree,
wens, robh+dt, linux-kernel, maz, linux-arm-kernel, linux-gpio,
mripard, stefan, huangshuosheng, jason
On Wed, 08 Jul 2020 15:19:27 +0800, Frank Lee wrote:
> This patch adds binding to a100's ccu clock and r-ccu clock.
>
> Signed-off-by: Frank Lee <frank@allwinnertech.com>
> ---
> .../devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml | 7 ++++++-
> 1 file changed, 6 insertions(+), 1 deletion(-)
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v3 01/16] dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and R-CCU
2020-07-13 22:54 ` Rob Herring
@ 2020-07-13 23:33 ` Rob Herring
0 siblings, 0 replies; 26+ messages in thread
From: Rob Herring @ 2020-07-13 23:33 UTC (permalink / raw)
To: Frank Lee
Cc: Michael Turquette, Linus Walleij, Corentin Labbe, liyong,
Srinivas Kandagatla, Icenowy Zheng, Philipp Zabel, Linux I2C,
Gregory CLEMENT, Stephen Boyd, Amit Kucheria, bage,
Thomas Gleixner, open list:THERMAL, Daniel Lezcano,
Vasily Khoruzhick, Ondrej Jirman, Yangtao Li, Lee Jones,
Zhang Rui, linux-clk, devicetree, Chen-Yu Tsai, linux-kernel,
Marc Zyngier,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE,
open list:GPIO SUBSYSTEM, Maxime Ripard, Stefan Mavrodiev,
huangshuosheng, Jason Cooper
On Mon, Jul 13, 2020 at 4:54 PM Rob Herring <robh@kernel.org> wrote:
>
> On Wed, 08 Jul 2020 15:19:27 +0800, Frank Lee wrote:
> > This patch adds binding to a100's ccu clock and r-ccu clock.
> >
> > Signed-off-by: Frank Lee <frank@allwinnertech.com>
> > ---
> > .../devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml | 7 ++++++-
> > 1 file changed, 6 insertions(+), 1 deletion(-)
> >
>
> Reviewed-by: Rob Herring <robh@kernel.org>
Note that your series isn't threaded properly. Please send series
threaded (in reply to cover letter or 1st patch).
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH v3 02/16] clk: sunxi-ng: add support for the Allwinner A100 CCU
2020-07-08 7:19 [PATCH v3 00/16] Allwinner A100 Initial support Frank Lee
2020-07-08 7:19 ` [PATCH v3 01/16] dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and R-CCU Frank Lee
@ 2020-07-08 7:19 ` Frank Lee
2020-07-08 7:19 ` [PATCH v3 03/16] dt-bindings: pinctrl: sunxi: Add A100 pinctrl bindings Frank Lee
` (9 subsequent siblings)
11 siblings, 0 replies; 26+ messages in thread
From: Frank Lee @ 2020-07-08 7:19 UTC (permalink / raw)
To: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, clabbe, icenowy, megous, stefan, bage
Cc: devicetree, linux-arm-kernel, linux-kernel, linux-clk, linux-i2c,
linux-gpio, linux-pm, huangshuosheng, liyong, Frank Lee
Add support for a100 in the sunxi-ng CCU framework.
Signed-off-by: Frank Lee <frank@allwinnertech.com>
---
drivers/clk/sunxi-ng/Kconfig | 10 +
drivers/clk/sunxi-ng/Makefile | 2 +
drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c | 214 +++++
drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h | 21 +
drivers/clk/sunxi-ng/ccu-sun50i-a100.c | 1276 +++++++++++++++++++++++++
drivers/clk/sunxi-ng/ccu-sun50i-a100.h | 56 ++
include/dt-bindings/clock/sun50i-a100-ccu.h | 116 +++
include/dt-bindings/clock/sun50i-a100-r-ccu.h | 23 +
include/dt-bindings/reset/sun50i-a100-ccu.h | 68 ++
include/dt-bindings/reset/sun50i-a100-r-ccu.h | 18 +
10 files changed, 1804 insertions(+)
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100.h
create mode 100644 include/dt-bindings/clock/sun50i-a100-ccu.h
create mode 100644 include/dt-bindings/clock/sun50i-a100-r-ccu.h
create mode 100644 include/dt-bindings/reset/sun50i-a100-ccu.h
create mode 100644 include/dt-bindings/reset/sun50i-a100-r-ccu.h
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index cdf3330..ce5f584 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -17,6 +17,16 @@ config SUN50I_A64_CCU
default ARM64 && ARCH_SUNXI
depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
+config SUN50I_A100_CCU
+ bool "Support for the Allwinner A100 CCU"
+ default ARM64 && ARCH_SUNXI
+ depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
+
+config SUN50I_A100_R_CCU
+ bool "Support for the Allwinner A100 PRCM CCU"
+ default ARM64 && ARCH_SUNXI
+ depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
+
config SUN50I_H6_CCU
bool "Support for the Allwinner H6 CCU"
default ARM64 && ARCH_SUNXI
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index 4c7bee8..3eb5cff 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -23,6 +23,8 @@ obj-y += ccu_mp.o
# SoC support
obj-$(CONFIG_SUNIV_F1C100S_CCU) += ccu-suniv-f1c100s.o
obj-$(CONFIG_SUN50I_A64_CCU) += ccu-sun50i-a64.o
+obj-$(CONFIG_SUN50I_A100_CCU) += ccu-sun50i-a100.o
+obj-$(CONFIG_SUN50I_A100_R_CCU) += ccu-sun50i-a100-r.o
obj-$(CONFIG_SUN50I_H6_CCU) += ccu-sun50i-h6.o
obj-$(CONFIG_SUN50I_H6_R_CCU) += ccu-sun50i-h6-r.o
obj-$(CONFIG_SUN4I_A10_CCU) += ccu-sun4i-a10.o
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c
new file mode 100644
index 0000000..d6dbd355
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c
@@ -0,0 +1,214 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020 Frank Lee <frank@allwinnertech.com>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+
+#include "ccu_common.h"
+#include "ccu_reset.h"
+
+#include "ccu_div.h"
+#include "ccu_gate.h"
+#include "ccu_mp.h"
+#include "ccu_nm.h"
+
+#include "ccu-sun50i-a100-r.h"
+
+static const char * const cpus_r_apb2_parents[] = { "dcxo24M", "osc32k",
+ "iosc", "pll-periph0" };
+static const struct ccu_mux_var_prediv cpus_r_apb2_predivs[] = {
+ { .index = 3, .shift = 0, .width = 5 },
+};
+
+static struct ccu_div r_cpus_clk = {
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+
+ .mux = {
+ .shift = 24,
+ .width = 2,
+
+ .var_predivs = cpus_r_apb2_predivs,
+ .n_var_predivs = ARRAY_SIZE(cpus_r_apb2_predivs),
+ },
+
+ .common = {
+ .reg = 0x000,
+ .features = CCU_FEATURE_VARIABLE_PREDIV,
+ .hw.init = CLK_HW_INIT_PARENTS("cpus",
+ cpus_r_apb2_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static CLK_FIXED_FACTOR_HW(r_ahb_clk, "r-ahb", &r_cpus_clk.common.hw, 1, 1, 0);
+
+static struct ccu_div r_apb1_clk = {
+ .div = _SUNXI_CCU_DIV(0, 2),
+
+ .common = {
+ .reg = 0x00c,
+ .hw.init = CLK_HW_INIT("r-apb1",
+ "r-ahb",
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static struct ccu_div r_apb2_clk = {
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+
+ .mux = {
+ .shift = 24,
+ .width = 2,
+
+ .var_predivs = cpus_r_apb2_predivs,
+ .n_var_predivs = ARRAY_SIZE(cpus_r_apb2_predivs),
+ },
+
+ .common = {
+ .reg = 0x010,
+ .features = CCU_FEATURE_VARIABLE_PREDIV,
+ .hw.init = CLK_HW_INIT_PARENTS("r-apb2",
+ cpus_r_apb2_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static const struct clk_parent_data clk_parent_r_apb1[] = {
+ { .hw = &r_apb1_clk.common.hw },
+};
+
+static const struct clk_parent_data clk_parent_r_apb2[] = {
+ { .hw = &r_apb2_clk.common.hw },
+};
+
+static SUNXI_CCU_GATE_DATA(r_apb1_timer_clk, "r-apb1-timer", clk_parent_r_apb1,
+ 0x11c, BIT(0), 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb1_twd_clk, "r-apb1-twd", clk_parent_r_apb1,
+ 0x12c, BIT(0), 0);
+
+static const char * const r_apb1_pwm_clk_parents[] = { "dcxo24M", "osc32k",
+ "iosc" };
+static SUNXI_CCU_MUX(r_apb1_pwm_clk, "r-apb1-pwm", r_apb1_pwm_clk_parents,
+ 0x130, 24, 2, 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb1_bus_pwm_clk, "r-apb1-bus-pwm",
+ clk_parent_r_apb1, 0x13c, BIT(0), 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb1_ppu_clk, "r-apb1-ppu", clk_parent_r_apb1,
+ 0x17c, BIT(0), 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb2_uart_clk, "r-apb2-uart", clk_parent_r_apb2,
+ 0x18c, BIT(0), 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb2_i2c0_clk, "r-apb2-i2c0", clk_parent_r_apb2,
+ 0x19c, BIT(0), 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb2_i2c1_clk, "r-apb2-i2c1", clk_parent_r_apb2,
+ 0x19c, BIT(1), 0);
+
+static const char * const r_apb1_ir_rx_parents[] = { "osc32k", "dcxo24M" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(r_apb1_ir_rx_clk, "r-apb1-ir-rx",
+ r_apb1_ir_rx_parents, 0x1c0,
+ 0, 5, /* M */
+ 8, 2, /* P */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb1_bus_ir_rx_clk, "r-apb1-bus-ir-rx",
+ clk_parent_r_apb1, 0x1cc, BIT(0), 0);
+
+static SUNXI_CCU_GATE(r_ahb_bus_rtc_clk, "r-ahb-rtc", "r-ahb",
+ 0x20c, BIT(0), 0);
+
+static struct ccu_common *sun50i_a100_r_ccu_clks[] = {
+ &r_cpus_clk.common,
+ &r_apb1_clk.common,
+ &r_apb2_clk.common,
+ &r_apb1_timer_clk.common,
+ &r_apb1_twd_clk.common,
+ &r_apb1_pwm_clk.common,
+ &r_apb1_bus_pwm_clk.common,
+ &r_apb1_ppu_clk.common,
+ &r_apb2_uart_clk.common,
+ &r_apb2_i2c0_clk.common,
+ &r_apb2_i2c1_clk.common,
+ &r_apb1_ir_rx_clk.common,
+ &r_apb1_bus_ir_rx_clk.common,
+ &r_ahb_bus_rtc_clk.common,
+};
+
+static struct clk_hw_onecell_data sun50i_a100_r_hw_clks = {
+ .hws = {
+ [CLK_R_CPUS] = &r_cpus_clk.common.hw,
+ [CLK_R_AHB] = &r_ahb_clk.hw,
+ [CLK_R_APB1] = &r_apb1_clk.common.hw,
+ [CLK_R_APB2] = &r_apb2_clk.common.hw,
+ [CLK_R_APB1_TIMER] = &r_apb1_timer_clk.common.hw,
+ [CLK_R_APB1_TWD] = &r_apb1_twd_clk.common.hw,
+ [CLK_R_APB1_PWM] = &r_apb1_pwm_clk.common.hw,
+ [CLK_R_APB1_BUS_PWM] = &r_apb1_bus_pwm_clk.common.hw,
+ [CLK_R_APB1_PPU] = &r_apb1_ppu_clk.common.hw,
+ [CLK_R_APB2_UART] = &r_apb2_uart_clk.common.hw,
+ [CLK_R_APB2_I2C0] = &r_apb2_i2c0_clk.common.hw,
+ [CLK_R_APB2_I2C1] = &r_apb2_i2c1_clk.common.hw,
+ [CLK_R_APB1_IR] = &r_apb1_ir_rx_clk.common.hw,
+ [CLK_R_APB1_BUS_IR] = &r_apb1_bus_ir_rx_clk.common.hw,
+ [CLK_R_AHB_BUS_RTC] = &r_ahb_bus_rtc_clk.common.hw,
+ },
+ .num = CLK_NUMBER,
+};
+
+static struct ccu_reset_map sun50i_a100_r_ccu_resets[] = {
+ [RST_R_APB1_TIMER] = { 0x11c, BIT(16) },
+ [RST_R_APB1_BUS_PWM] = { 0x13c, BIT(16) },
+ [RST_R_APB1_PPU] = { 0x17c, BIT(16) },
+ [RST_R_APB2_UART] = { 0x18c, BIT(16) },
+ [RST_R_APB2_I2C0] = { 0x19c, BIT(16) },
+ [RST_R_APB2_I2C1] = { 0x19c, BIT(17) },
+ [RST_R_APB1_BUS_IR] = { 0x1cc, BIT(16) },
+ [RST_R_AHB_BUS_RTC] = { 0x20c, BIT(16) },
+};
+
+static const struct sunxi_ccu_desc sun50i_a100_r_ccu_desc = {
+ .ccu_clks = sun50i_a100_r_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun50i_a100_r_ccu_clks),
+
+ .hw_clks = &sun50i_a100_r_hw_clks,
+
+ .resets = sun50i_a100_r_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun50i_a100_r_ccu_resets),
+};
+
+static int sun50i_a100_r_ccu_probe(struct platform_device *pdev)
+{
+ void __iomem *reg;
+
+ reg = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(reg))
+ return PTR_ERR(reg);
+
+ return sunxi_ccu_probe(pdev->dev.of_node, reg, &sun50i_a100_r_ccu_desc);
+}
+
+static const struct of_device_id sun50i_a100_r_ccu_ids[] = {
+ { .compatible = "allwinner,sun50i-a100-r-ccu" },
+ { }
+};
+
+static struct platform_driver sun50i_a100_r_ccu_driver = {
+ .probe = sun50i_a100_r_ccu_probe,
+ .driver = {
+ .name = "sun50i-a100-r-ccu",
+ .of_match_table = sun50i_a100_r_ccu_ids,
+ },
+};
+module_platform_driver(sun50i_a100_r_ccu_driver);
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h
new file mode 100644
index 0000000..8331fbc
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2020 Frank Lee <frank@allwinnertech.com>
+ */
+
+#ifndef _CCU_SUN50I_A100_R_H
+#define _CCU_SUN50I_A100_R_H
+
+#include <dt-bindings/clock/sun50i-a100-r-ccu.h>
+#include <dt-bindings/reset/sun50i-a100-r-ccu.h>
+
+#define CLK_R_CPUS 0
+#define CLK_R_AHB 1
+
+/* exported except APB1 for R_PIO */
+
+#define CLK_R_APB2 3
+
+#define CLK_NUMBER (CLK_R_AHB_BUS_RTC + 1)
+
+#endif /* _CCU_SUN50I_A100_R_H */
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100.c b/drivers/clk/sunxi-ng/ccu-sun50i-a100.c
new file mode 100644
index 0000000..98f32f8
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100.c
@@ -0,0 +1,1276 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020 Frank Lee <frank@allwinnertech.com>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+
+#include "ccu_common.h"
+#include "ccu_reset.h"
+
+#include "ccu_div.h"
+#include "ccu_gate.h"
+#include "ccu_mp.h"
+#include "ccu_mult.h"
+#include "ccu_nk.h"
+#include "ccu_nkm.h"
+#include "ccu_nkmp.h"
+#include "ccu_nm.h"
+
+#include "ccu-sun50i-a100.h"
+
+#define SUN50I_A100_PLL_SDM_ENABLE BIT(24)
+#define SUN50I_A100_PLL_OUTPUT_ENABLE BIT(27)
+#define SUN50I_A100_PLL_LOCK BIT(28)
+#define SUN50I_A100_PLL_LOCK_ENABLE BIT(29)
+#define SUN50I_A100_PLL_ENABLE BIT(31)
+
+#define SUN50I_A100_PLL_PERIPH1_PATTERN0 0xd1303333
+
+/*
+ * The CPU PLL is actually NP clock, with P being /1, /2 or /4. However
+ * P should only be used for output frequencies lower than 288 MHz.
+ *
+ * For now we can just model it as a multiplier clock, and force P to /1.
+ *
+ * The M factor is present in the register's description, but not in the
+ * frequency formula, and it's documented as "M is only used for backdoor
+ * testing", so it's not modelled and then force to 0.
+ */
+#define SUN50I_A100_PLL_CPUX_REG 0x000
+static struct ccu_mult pll_cpux_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .mult = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .common = {
+ .reg = 0x000,
+ .hw.init = CLK_HW_INIT("pll-cpux", "dcxo24M",
+ &ccu_mult_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+/* Some PLLs are input * N / div1 / P. Model them as NKMP with no K */
+#define SUN50I_A100_PLL_DDR0_REG 0x010
+static struct ccu_nkmp pll_ddr0_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .common = {
+ .reg = 0x010,
+ .hw.init = CLK_HW_INIT("pll-ddr0", "dcxo24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE |
+ CLK_IS_CRITICAL),
+ },
+};
+
+#define SUN50I_A100_PLL_PERIPH0_REG 0x020
+static struct ccu_nkmp pll_periph0_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .fixed_post_div = 2,
+ .common = {
+ .reg = 0x020,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-periph0", "dcxo24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_A100_PLL_PERIPH1_REG 0x028
+static struct ccu_nkmp pll_periph1_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .fixed_post_div = 2,
+ .common = {
+ .reg = 0x028,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-periph1", "dcxo24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+#define SUN50I_A100_PLL_PERIPH1_PATTERN0_REG 0x128
+
+#define SUN50I_A100_PLL_GPU_REG 0x030
+static struct ccu_nkmp pll_gpu_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .common = {
+ .reg = 0x030,
+ .hw.init = CLK_HW_INIT("pll-gpu", "dcxo24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+/*
+ * For Video PLLs, the output divider is described as "used for testing"
+ * in the user manual. So it's not modelled and forced to 0.
+ */
+#define SUN50I_A100_PLL_VIDEO0_REG 0x040
+static struct ccu_nm pll_video0_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .fixed_post_div = 4,
+ .common = {
+ .reg = 0x040,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-video0", "dcxo24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_A100_PLL_VIDEO1_REG 0x048
+static struct ccu_nm pll_video1_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .fixed_post_div = 4,
+ .common = {
+ .reg = 0x048,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-video1", "dcxo24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_A100_PLL_VIDEO2_REG 0x050
+static struct ccu_nm pll_video2_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .fixed_post_div = 4,
+ .common = {
+ .reg = 0x050,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-video2", "dcxo24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_A100_PLL_VE_REG 0x058
+static struct ccu_nkmp pll_ve_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .common = {
+ .reg = 0x058,
+ .hw.init = CLK_HW_INIT("pll-ve", "dcxo24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+/*
+ * The COM PLL has m0 dividers in addition to the usual N, M
+ * factors. Since we only need 1 frequencies from this PLL: 45.1584 MHz,
+ * ignore it for now.
+ */
+#define SUN50I_A100_PLL_COM_REG 0x060
+static struct ccu_sdm_setting pll_com_sdm_table[] = {
+ { .rate = 451584000, .pattern = 0xc0014396, .m = 2, .n = 37 },
+};
+
+static struct ccu_nm pll_com_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(0, 1),
+ .sdm = _SUNXI_CCU_SDM(pll_com_sdm_table, BIT(24),
+ 0x160, BIT(31)),
+ .common = {
+ .reg = 0x060,
+ .features = CCU_FEATURE_SIGMA_DELTA_MOD,
+ .hw.init = CLK_HW_INIT("pll-com", "dcxo24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_A100_PLL_VIDEO3_REG 0x068
+static struct ccu_nm pll_video3_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .fixed_post_div = 4,
+ .common = {
+ .reg = 0x068,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-video3", "dcxo24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+/*
+ * The Audio PLL has m0, m1 dividers in addition to the usual N, M
+ * factors. Since we only need 4 frequencies from this PLL: 22.5792 MHz,
+ * 24.576 MHz, 90.3168MHz and 98.304MHz ignore them for now.
+ * Enforce the default for them, which is m0 = 1, m1 = 0.
+ */
+#define SUN50I_A100_PLL_AUDIO_REG 0x078
+static struct ccu_sdm_setting pll_audio_sdm_table[] = {
+ { .rate = 45158400, .pattern = 0xc001bcd3, .m = 18, .n = 33 },
+ { .rate = 49152000, .pattern = 0xc001eb85, .m = 20, .n = 40 },
+ { .rate = 180633600, .pattern = 0xc001288d, .m = 3, .n = 22 },
+ { .rate = 196608000, .pattern = 0xc001eb85, .m = 5, .n = 40 },
+};
+
+static struct ccu_nm pll_audio_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(16, 6),
+ .fixed_post_div = 2,
+ .sdm = _SUNXI_CCU_SDM(pll_audio_sdm_table, BIT(24),
+ 0x178, BIT(31)),
+ .common = {
+ .reg = 0x078,
+ .features = CCU_FEATURE_FIXED_POSTDIV |
+ CCU_FEATURE_SIGMA_DELTA_MOD,
+ .hw.init = CLK_HW_INIT("pll-audio", "dcxo24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+static const char * const cpux_parents[] = { "dcxo24M", "osc32k",
+ "iosc", "pll-cpux",
+ "pll-periph0" };
+static SUNXI_CCU_MUX(cpux_clk, "cpux", cpux_parents,
+ 0x500, 24, 3, CLK_SET_RATE_PARENT | CLK_IS_CRITICAL);
+static SUNXI_CCU_M(axi_clk, "axi", "cpux", 0x500, 0, 2, 0);
+static SUNXI_CCU_M(cpux_apb_clk, "cpux-apb", "cpux", 0x500, 8, 2, 0);
+
+static const char * const psi_ahb1_ahb2_parents[] = { "dcxo24M", "osc32k",
+ "iosc", "pll-periph0",
+ "pll-periph0-2x" };
+static SUNXI_CCU_MP_WITH_MUX(psi_ahb1_ahb2_clk, "psi-ahb1-ahb2",
+ psi_ahb1_ahb2_parents, 0x510,
+ 0, 2, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ 0);
+
+static const char * const ahb3_apb1_apb2_parents[] = { "dcxo24M", "osc32k",
+ "psi-ahb1-ahb2",
+ "pll-periph0",
+ "pll-periph0-2x" };
+static SUNXI_CCU_MP_WITH_MUX(ahb3_clk, "ahb3", ahb3_apb1_apb2_parents, 0x51c,
+ 0, 2, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX(apb1_clk, "apb1", ahb3_apb1_apb2_parents, 0x520,
+ 0, 2, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX(apb2_clk, "apb2", ahb3_apb1_apb2_parents, 0x524,
+ 0, 2, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ 0);
+
+static const char * const mbus_parents[] = { "dcxo24M", "pll-ddr0",
+ "pll-periph0",
+ "pll-periph0-2x" };
+static SUNXI_CCU_M_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents, 0x540,
+ 0, 3, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ CLK_IS_CRITICAL);
+
+static const char * const de_parents[] = { "pll-com", "pll-periph0-2x" };
+static SUNXI_CCU_M_WITH_MUX_GATE(de_clk, "de0", de_parents, 0x600,
+ 0, 4, /* M */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(bus_de_clk, "bus-de", "psi-ahb1-ahb2",
+ 0x60c, BIT(0), 0);
+
+static const char * const g2d_parents[] = { "pll-com", "pll-periph0-2x",
+ "pll-video0-2x", "pll-video1-2x",
+ "pll-video2-2x"};
+static SUNXI_CCU_M_WITH_MUX_GATE(g2d_clk, "g2d",
+ g2d_parents,
+ 0x630,
+ 0, 4, /* M */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_g2d_clk, "bus-g2d", "psi-ahb1-ahb2",
+ 0x63c, BIT(0), 0);
+
+static const char * const gpu_parents[] = { "pll-gpu" };
+static SUNXI_CCU_M_WITH_MUX_GATE(gpu_clk, "gpu", gpu_parents, 0x670,
+ 0, 2, /* M */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_gpu_clk, "bus-gpu", "psi-ahb1-ahb2",
+ 0x67c, BIT(0), 0);
+
+static const char * const ce_parents[] = { "dcxo24M", "pll-periph0-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(ce_clk, "ce", ce_parents, 0x680,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_ce_clk, "bus-ce", "psi-ahb1-ahb2",
+ 0x68c, BIT(0), 0);
+
+static const char * const ve_parents[] = { "pll-ve" };
+static SUNXI_CCU_M_WITH_MUX_GATE(ve_clk, "ve", ve_parents, 0x690,
+ 0, 3, /* M */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(bus_ve_clk, "bus-ve", "psi-ahb1-ahb2",
+ 0x69c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_dma_clk, "bus-dma", "psi-ahb1-ahb2",
+ 0x70c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_msgbox_clk, "bus-msgbox", "psi-ahb1-ahb2",
+ 0x71c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_spinlock_clk, "bus-spinlock", "psi-ahb1-ahb2",
+ 0x72c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_hstimer_clk, "bus-hstimer", "psi-ahb1-ahb2",
+ 0x73c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(avs_clk, "avs", "dcxo24M", 0x740, BIT(31), 0);
+
+static SUNXI_CCU_GATE(bus_dbg_clk, "bus-dbg", "psi-ahb1-ahb2",
+ 0x78c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_psi_clk, "bus-psi", "psi-ahb1-ahb2",
+ 0x79c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_pwm_clk, "bus-pwm", "apb1", 0x7ac, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_iommu_clk, "bus-iommu", "apb1", 0x7bc, BIT(0), 0);
+
+static SUNXI_CCU_GATE(mbus_dma_clk, "mbus-dma", "mbus",
+ 0x804, BIT(0), 0);
+static SUNXI_CCU_GATE(mbus_ve_clk, "mbus-ve", "mbus",
+ 0x804, BIT(1), 0);
+static SUNXI_CCU_GATE(mbus_ce_clk, "mbus-ce", "mbus",
+ 0x804, BIT(2), 0);
+static SUNXI_CCU_GATE(mbus_nand_clk, "mbus-nand", "mbus",
+ 0x804, BIT(5), 0);
+static SUNXI_CCU_GATE(mbus_csi_clk, "mbus-csi", "mbus",
+ 0x804, BIT(8), 0);
+static SUNXI_CCU_GATE(mbus_isp_clk, "mbus-isp", "mbus",
+ 0x804, BIT(9), 0);
+static SUNXI_CCU_GATE(mbus_g2d_clk, "mbus-g2d", "mbus",
+ 0x804, BIT(10), 0);
+
+static SUNXI_CCU_GATE(bus_dram_clk, "bus-dram", "psi-ahb1-ahb2",
+ 0x80c, BIT(0), CLK_IS_CRITICAL);
+
+static const char * const nand_spi_parents[] = { "dcxo24M",
+ "pll-periph0",
+ "pll-periph1",
+ "pll-periph0-2x",
+ "pll-periph1-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(nand0_clk, "nand0", nand_spi_parents, 0x810,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(nand1_clk, "nand1", nand_spi_parents, 0x814,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_nand_clk, "bus-nand", "ahb3", 0x82c, BIT(0), 0);
+
+static const char * const mmc_parents[] = { "dcxo24M", "pll-periph0-2x",
+ "pll-periph1-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc0_clk, "mmc0", mmc_parents, 0x830,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 2, /* post-div */
+ CLK_SET_RATE_NO_REPARENT);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc1_clk, "mmc1", mmc_parents, 0x834,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 2, /* post-div */
+ CLK_SET_RATE_NO_REPARENT);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc2_clk, "mmc2", mmc_parents, 0x838,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 2, /* post-div */
+ CLK_SET_RATE_NO_REPARENT);
+
+static SUNXI_CCU_GATE(bus_mmc0_clk, "bus-mmc0", "ahb3", 0x84c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_mmc1_clk, "bus-mmc1", "ahb3", 0x84c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_mmc2_clk, "bus-mmc2", "ahb3", 0x84c, BIT(2), 0);
+
+static SUNXI_CCU_GATE(bus_uart0_clk, "bus-uart0", "apb2", 0x90c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_uart1_clk, "bus-uart1", "apb2", 0x90c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_uart2_clk, "bus-uart2", "apb2", 0x90c, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2", 0x90c, BIT(3), 0);
+static SUNXI_CCU_GATE(bus_uart4_clk, "bus-uart4", "apb2", 0x90c, BIT(4), 0);
+
+static SUNXI_CCU_GATE(bus_i2c0_clk, "bus-i2c0", "apb2", 0x91c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_i2c1_clk, "bus-i2c1", "apb2", 0x91c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_i2c2_clk, "bus-i2c2", "apb2", 0x91c, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_i2c3_clk, "bus-i2c3", "apb2", 0x91c, BIT(3), 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi0_clk, "spi0", nand_spi_parents, 0x940,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi1_clk, "spi1", nand_spi_parents, 0x944,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi2_clk, "spi2", nand_spi_parents, 0x948,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_spi0_clk, "bus-spi0", "ahb3", 0x96c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_spi1_clk, "bus-spi1", "ahb3", 0x96c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_spi2_clk, "bus-spi2", "ahb3", 0x96c, BIT(2), 0);
+
+static SUNXI_CCU_GATE(emac_25m_clk, "emac-25m", "ahb3", 0x970,
+ BIT(31) | BIT(30), 0);
+
+static SUNXI_CCU_GATE(bus_emac_clk, "bus-emac", "ahb3", 0x97c, BIT(0), 0);
+
+static const char * const ir_parents[] = { "osc32k", "iosc",
+ "pll-periph0", "pll-periph1" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(ir_rx_clk, "ir-rx", ir_parents, 0x990,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_ir_rx_clk, "bus-ir-rx", "ahb3", 0x99c, BIT(0), 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(ir_tx_clk, "ir-tx", ir_parents, 0x9c0,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_ir_tx_clk, "bus-ir-tx", "apb1", 0x9cc, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_gpadc_clk, "bus-gpadc", "apb1", 0x9ec, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_ths_clk, "bus-ths", "apb1", 0x9fc, BIT(0), 0);
+
+static const char * const audio_parents[] = { "pll-audio", "pll-com-audio" };
+static struct ccu_div i2s0_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa10,
+ .hw.init = CLK_HW_INIT_PARENTS("i2s0",
+ audio_parents,
+ &ccu_div_ops,
+ CLK_SET_RATE_PARENT),
+ },
+};
+
+static struct ccu_div i2s1_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa14,
+ .hw.init = CLK_HW_INIT_PARENTS("i2s1",
+ audio_parents,
+ &ccu_div_ops,
+ CLK_SET_RATE_PARENT),
+ },
+};
+
+static struct ccu_div i2s2_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa18,
+ .hw.init = CLK_HW_INIT_PARENTS("i2s2",
+ audio_parents,
+ &ccu_div_ops,
+ CLK_SET_RATE_PARENT),
+ },
+};
+
+static struct ccu_div i2s3_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa1c,
+ .hw.init = CLK_HW_INIT_PARENTS("i2s3",
+ audio_parents,
+ &ccu_div_ops,
+ CLK_SET_RATE_PARENT),
+ },
+};
+
+static SUNXI_CCU_GATE(bus_i2s0_clk, "bus-i2s0", "apb1", 0xa20, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_i2s1_clk, "bus-i2s1", "apb1", 0xa20, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_i2s2_clk, "bus-i2s2", "apb1", 0xa20, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_i2s3_clk, "bus-i2s3", "apb1", 0xa20, BIT(3), 0);
+
+static struct ccu_div spdif_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa24,
+ .hw.init = CLK_HW_INIT_PARENTS("spdif",
+ audio_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static SUNXI_CCU_GATE(bus_spdif_clk, "bus-spdif", "apb1", 0xa2c, BIT(0), 0);
+
+static struct ccu_div dmic_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa40,
+ .hw.init = CLK_HW_INIT_PARENTS("dmic",
+ audio_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static SUNXI_CCU_GATE(bus_dmic_clk, "bus-dmic", "apb1", 0xa4c, BIT(0), 0);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(audio_codec_dac_clk, "audio-codec-dac",
+ audio_parents, 0xa50,
+ 0, 4, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(audio_codec_adc_clk, "audio-codec-adc",
+ audio_parents, 0xa54,
+ 0, 4, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(audio_codec_4x_clk, "audio-codec-4x",
+ audio_parents, 0xa58,
+ 0, 4, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_audio_codec_clk, "bus-audio-codec", "apb1", 0xa5c,
+ BIT(0), 0);
+
+/*
+ * There are OHCI 12M clock source selection bits for 2 USB 2.0 ports.
+ * We will force them to 0 (12M divided from 48M).
+ */
+#define SUN50I_A100_USB0_CLK_REG 0xa70
+#define SUN50I_A100_USB1_CLK_REG 0xa74
+
+static SUNXI_CCU_GATE(usb_ohci0_clk, "usb-ohci0", "osc12M", 0xa70, BIT(31), 0);
+static SUNXI_CCU_GATE(usb_phy0_clk, "usb-phy0", "dcxo24M", 0xa70, BIT(29), 0);
+
+static SUNXI_CCU_GATE(usb_ohci1_clk, "usb-ohci1", "osc12M", 0xa74, BIT(31), 0);
+static SUNXI_CCU_GATE(usb_phy1_clk, "usb-phy1", "dcxo24M", 0xa74, BIT(29), 0);
+
+static SUNXI_CCU_GATE(bus_ohci0_clk, "bus-ohci0", "ahb3", 0xa8c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_ohci1_clk, "bus-ohci1", "ahb3", 0xa8c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_ehci0_clk, "bus-ehci0", "ahb3", 0xa8c, BIT(4), 0);
+static SUNXI_CCU_GATE(bus_ehci1_clk, "bus-ehci1", "ahb3", 0xa8c, BIT(5), 0);
+static SUNXI_CCU_GATE(bus_otg_clk, "bus-otg", "ahb3", 0xa8c, BIT(8), 0);
+
+static SUNXI_CCU_GATE(bus_lradc_clk, "bus-lradc", "ahb3", 0xa9c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_dpss_top0_clk, "bus-dpss-top0", "ahb3",
+ 0xabc, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_dpss_top1_clk, "bus-dpss-top1", "ahb3",
+ 0xacc, BIT(0), 0);
+
+static const char * const mipi_dsi_parents[] = { "dcxo24M", "pll-periph0-2x",
+ "pll-periph0" };
+static SUNXI_CCU_M_WITH_MUX_GATE(mipi_dsi_clk, "mipi-dsi",
+ mipi_dsi_parents,
+ 0xb24,
+ 0, 4, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_mipi_dsi_clk, "bus-mipi-dsi", "ahb3",
+ 0xb4c, BIT(0), 0);
+
+static const char * const tcon_lcd_parents[] = { "pll-video0-4x",
+ "pll-video1-4x",
+ "pll-video2-4x",
+ "pll-video3-4x",
+ "pll-periph0-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(tcon_lcd_clk, "tcon-lcd0",
+ tcon_lcd_parents, 0xb60,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_tcon_lcd_clk, "bus-tcon-lcd0", "ahb3",
+ 0xb7c, BIT(0), 0);
+
+static const char * const ledc_parents[] = { "dcxo24M",
+ "pll-periph0" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(ledc_clk, "ledc",
+ ledc_parents, 0xbf0,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_ledc_clk, "bus-ledc", "ahb3", 0xbfc, BIT(0), 0);
+
+static const char * const csi_top_parents[] = { "pll-periph0-2x",
+ "pll-video0-2x",
+ "pll-video1-2x",
+ "pll-video2-2x",
+ "pll-video3-2x" };
+static SUNXI_CCU_M_WITH_MUX_GATE(csi_top_clk, "csi-top",
+ csi_top_parents, 0xc04,
+ 0, 4, /* M */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static const char * const csi0_mclk_parents[] = { "dcxo24M", "pll-video2",
+ "pll-video3", "pll-video0",
+ "pll-video1" };
+static SUNXI_CCU_M_WITH_MUX_GATE(csi0_mclk_clk, "csi0-mclk",
+ csi0_mclk_parents, 0xc08,
+ 0, 5, /* M */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static const char * const csi1_mclk_parents[] = { "dcxo24M", "pll-video3",
+ "pll-video0", "pll-video1",
+ "pll-video2" };
+static SUNXI_CCU_M_WITH_MUX_GATE(csi1_mclk_clk, "csi1-mclk",
+ csi1_mclk_parents, 0xc0c,
+ 0, 5, /* M */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_csi_clk, "bus-csi", "ahb3", 0xc1c, BIT(0), 0);
+
+static const char * const csi_isp_parents[] = { "pll-periph0-2x",
+ "pll-video0-2x",
+ "pll-video1-2x",
+ "pll-video2-2x",
+ "pll-video3-2x" };
+static SUNXI_CCU_M_WITH_MUX_GATE(csi_isp_clk, "csi-isp",
+ csi_isp_parents, 0xc20,
+ 0, 5, /* M */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+/* Fixed factor clocks */
+static CLK_FIXED_FACTOR_FW_NAME(osc12M_clk, "osc12M", "hosc", 2, 1, 0);
+
+static CLK_FIXED_FACTOR_HW(pll_com_audio_clk, "pll-com-audio",
+ &pll_com_clk.common.hw,
+ 5, 1, CLK_SET_RATE_PARENT);
+
+static CLK_FIXED_FACTOR_HW(pll_periph0_2x_clk, "pll-periph0-2x",
+ &pll_periph0_clk.common.hw,
+ 1, 2, 0);
+
+static CLK_FIXED_FACTOR_HW(pll_periph1_2x_clk, "pll-periph1-2x",
+ &pll_periph1_clk.common.hw,
+ 1, 2, 0);
+
+static const struct clk_hw *pll_video0_parents[] = {
+ &pll_video0_clk.common.hw
+};
+static CLK_FIXED_FACTOR_HWS(pll_video0_4x_clk, "pll-video0-4x",
+ pll_video0_parents,
+ 1, 4, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HWS(pll_video0_2x_clk, "pll-video0-2x",
+ pll_video0_parents,
+ 1, 2, CLK_SET_RATE_PARENT);
+
+static const struct clk_hw *pll_video1_parents[] = {
+ &pll_video1_clk.common.hw
+};
+static CLK_FIXED_FACTOR_HWS(pll_video1_4x_clk, "pll-video1-4x",
+ pll_video1_parents,
+ 1, 4, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HWS(pll_video1_2x_clk, "pll-video1-2x",
+ pll_video1_parents,
+ 1, 2, CLK_SET_RATE_PARENT);
+
+static const struct clk_hw *pll_video2_parents[] = {
+ &pll_video2_clk.common.hw
+};
+static CLK_FIXED_FACTOR_HWS(pll_video2_4x_clk, "pll-video2-4x",
+ pll_video2_parents,
+ 1, 4, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HWS(pll_video2_2x_clk, "pll-video2-2x",
+ pll_video2_parents,
+ 1, 2, CLK_SET_RATE_PARENT);
+
+static const struct clk_hw *pll_video3_parents[] = {
+ &pll_video3_clk.common.hw
+};
+static CLK_FIXED_FACTOR_HWS(pll_video3_4x_clk, "pll-video3-4x",
+ pll_video3_parents,
+ 1, 4, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HWS(pll_video3_2x_clk, "pll-video3-2x",
+ pll_video3_parents,
+ 1, 2, CLK_SET_RATE_PARENT);
+
+static struct ccu_common *sun50i_a100_ccu_clks[] = {
+ &pll_cpux_clk.common,
+ &pll_ddr0_clk.common,
+ &pll_periph0_clk.common,
+ &pll_periph1_clk.common,
+ &pll_gpu_clk.common,
+ &pll_video0_clk.common,
+ &pll_video1_clk.common,
+ &pll_video2_clk.common,
+ &pll_video3_clk.common,
+ &pll_ve_clk.common,
+ &pll_com_clk.common,
+ &pll_audio_clk.common,
+ &cpux_clk.common,
+ &axi_clk.common,
+ &cpux_apb_clk.common,
+ &psi_ahb1_ahb2_clk.common,
+ &ahb3_clk.common,
+ &apb1_clk.common,
+ &apb2_clk.common,
+ &mbus_clk.common,
+ &de_clk.common,
+ &bus_de_clk.common,
+ &g2d_clk.common,
+ &bus_g2d_clk.common,
+ &gpu_clk.common,
+ &bus_gpu_clk.common,
+ &ce_clk.common,
+ &bus_ce_clk.common,
+ &ve_clk.common,
+ &bus_ve_clk.common,
+ &bus_dma_clk.common,
+ &bus_msgbox_clk.common,
+ &bus_spinlock_clk.common,
+ &bus_hstimer_clk.common,
+ &avs_clk.common,
+ &bus_dbg_clk.common,
+ &bus_psi_clk.common,
+ &bus_pwm_clk.common,
+ &bus_iommu_clk.common,
+ &mbus_dma_clk.common,
+ &mbus_ve_clk.common,
+ &mbus_ce_clk.common,
+ &mbus_nand_clk.common,
+ &mbus_csi_clk.common,
+ &mbus_isp_clk.common,
+ &mbus_g2d_clk.common,
+ &bus_dram_clk.common,
+ &nand0_clk.common,
+ &nand1_clk.common,
+ &bus_nand_clk.common,
+ &mmc0_clk.common,
+ &mmc1_clk.common,
+ &mmc2_clk.common,
+ &bus_mmc0_clk.common,
+ &bus_mmc1_clk.common,
+ &bus_mmc2_clk.common,
+ &bus_uart0_clk.common,
+ &bus_uart1_clk.common,
+ &bus_uart2_clk.common,
+ &bus_uart3_clk.common,
+ &bus_uart4_clk.common,
+ &bus_i2c0_clk.common,
+ &bus_i2c1_clk.common,
+ &bus_i2c2_clk.common,
+ &bus_i2c3_clk.common,
+ &spi0_clk.common,
+ &spi1_clk.common,
+ &spi2_clk.common,
+ &bus_spi0_clk.common,
+ &bus_spi1_clk.common,
+ &bus_spi2_clk.common,
+ &emac_25m_clk.common,
+ &bus_emac_clk.common,
+ &ir_rx_clk.common,
+ &bus_ir_rx_clk.common,
+ &ir_tx_clk.common,
+ &bus_ir_tx_clk.common,
+ &bus_gpadc_clk.common,
+ &bus_ths_clk.common,
+ &i2s0_clk.common,
+ &i2s1_clk.common,
+ &i2s2_clk.common,
+ &i2s3_clk.common,
+ &bus_i2s0_clk.common,
+ &bus_i2s1_clk.common,
+ &bus_i2s2_clk.common,
+ &bus_i2s3_clk.common,
+ &spdif_clk.common,
+ &bus_spdif_clk.common,
+ &dmic_clk.common,
+ &bus_dmic_clk.common,
+ &audio_codec_dac_clk.common,
+ &audio_codec_adc_clk.common,
+ &audio_codec_4x_clk.common,
+ &bus_audio_codec_clk.common,
+ &usb_ohci0_clk.common,
+ &usb_phy0_clk.common,
+ &usb_ohci1_clk.common,
+ &usb_phy1_clk.common,
+ &bus_ohci0_clk.common,
+ &bus_ohci1_clk.common,
+ &bus_ehci0_clk.common,
+ &bus_ehci1_clk.common,
+ &bus_otg_clk.common,
+ &bus_lradc_clk.common,
+ &bus_dpss_top0_clk.common,
+ &bus_dpss_top1_clk.common,
+ &mipi_dsi_clk.common,
+ &bus_mipi_dsi_clk.common,
+ &tcon_lcd_clk.common,
+ &bus_tcon_lcd_clk.common,
+ &ledc_clk.common,
+ &bus_ledc_clk.common,
+ &csi_top_clk.common,
+ &csi0_mclk_clk.common,
+ &csi1_mclk_clk.common,
+ &bus_csi_clk.common,
+ &csi_isp_clk.common,
+};
+
+static struct clk_hw_onecell_data sun50i_a100_hw_clks = {
+ .hws = {
+ [CLK_OSC12M] = &osc12M_clk.hw,
+ [CLK_PLL_CPUX] = &pll_cpux_clk.common.hw,
+ [CLK_PLL_DDR0] = &pll_ddr0_clk.common.hw,
+ [CLK_PLL_PERIPH0] = &pll_periph0_clk.common.hw,
+ [CLK_PLL_PERIPH0_2X] = &pll_periph0_2x_clk.hw,
+ [CLK_PLL_PERIPH1] = &pll_periph1_clk.common.hw,
+ [CLK_PLL_PERIPH1_2X] = &pll_periph1_2x_clk.hw,
+ [CLK_PLL_GPU] = &pll_gpu_clk.common.hw,
+ [CLK_PLL_VIDEO0] = &pll_video0_clk.common.hw,
+ [CLK_PLL_VIDEO0_2X] = &pll_video0_2x_clk.hw,
+ [CLK_PLL_VIDEO0_4X] = &pll_video0_4x_clk.hw,
+ [CLK_PLL_VIDEO1] = &pll_video1_clk.common.hw,
+ [CLK_PLL_VIDEO1_2X] = &pll_video1_2x_clk.hw,
+ [CLK_PLL_VIDEO1_4X] = &pll_video1_4x_clk.hw,
+ [CLK_PLL_VIDEO2] = &pll_video2_clk.common.hw,
+ [CLK_PLL_VIDEO2_2X] = &pll_video2_2x_clk.hw,
+ [CLK_PLL_VIDEO2_4X] = &pll_video2_4x_clk.hw,
+ [CLK_PLL_VIDEO3] = &pll_video3_clk.common.hw,
+ [CLK_PLL_VIDEO3_2X] = &pll_video3_2x_clk.hw,
+ [CLK_PLL_VIDEO3_4X] = &pll_video3_4x_clk.hw,
+ [CLK_PLL_VE] = &pll_ve_clk.common.hw,
+ [CLK_PLL_COM] = &pll_com_clk.common.hw,
+ [CLK_PLL_COM_AUDIO] = &pll_com_audio_clk.hw,
+ [CLK_PLL_AUDIO] = &pll_audio_clk.common.hw,
+ [CLK_CPUX] = &cpux_clk.common.hw,
+ [CLK_AXI] = &axi_clk.common.hw,
+ [CLK_CPUX_APB] = &cpux_apb_clk.common.hw,
+ [CLK_PSI_AHB1_AHB2] = &psi_ahb1_ahb2_clk.common.hw,
+ [CLK_AHB3] = &ahb3_clk.common.hw,
+ [CLK_APB1] = &apb1_clk.common.hw,
+ [CLK_APB2] = &apb2_clk.common.hw,
+ [CLK_MBUS] = &mbus_clk.common.hw,
+ [CLK_DE] = &de_clk.common.hw,
+ [CLK_BUS_DE] = &bus_de_clk.common.hw,
+ [CLK_G2D] = &g2d_clk.common.hw,
+ [CLK_BUS_G2D] = &bus_g2d_clk.common.hw,
+ [CLK_GPU] = &gpu_clk.common.hw,
+ [CLK_BUS_GPU] = &bus_gpu_clk.common.hw,
+ [CLK_CE] = &ce_clk.common.hw,
+ [CLK_BUS_CE] = &bus_ce_clk.common.hw,
+ [CLK_VE] = &ve_clk.common.hw,
+ [CLK_BUS_VE] = &bus_ve_clk.common.hw,
+ [CLK_BUS_DMA] = &bus_dma_clk.common.hw,
+ [CLK_BUS_MSGBOX] = &bus_msgbox_clk.common.hw,
+ [CLK_BUS_SPINLOCK] = &bus_spinlock_clk.common.hw,
+ [CLK_BUS_HSTIMER] = &bus_hstimer_clk.common.hw,
+ [CLK_AVS] = &avs_clk.common.hw,
+ [CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
+ [CLK_BUS_PSI] = &bus_psi_clk.common.hw,
+ [CLK_BUS_PWM] = &bus_pwm_clk.common.hw,
+ [CLK_BUS_IOMMU] = &bus_iommu_clk.common.hw,
+ [CLK_MBUS_DMA] = &mbus_dma_clk.common.hw,
+ [CLK_MBUS_VE] = &mbus_ve_clk.common.hw,
+ [CLK_MBUS_CE] = &mbus_ce_clk.common.hw,
+ [CLK_MBUS_NAND] = &mbus_nand_clk.common.hw,
+ [CLK_MBUS_CSI] = &mbus_csi_clk.common.hw,
+ [CLK_MBUS_ISP] = &mbus_isp_clk.common.hw,
+ [CLK_MBUS_G2D] = &mbus_g2d_clk.common.hw,
+ [CLK_BUS_DRAM] = &bus_dram_clk.common.hw,
+ [CLK_NAND0] = &nand0_clk.common.hw,
+ [CLK_NAND1] = &nand1_clk.common.hw,
+ [CLK_BUS_NAND] = &bus_nand_clk.common.hw,
+ [CLK_MMC0] = &mmc0_clk.common.hw,
+ [CLK_MMC1] = &mmc1_clk.common.hw,
+ [CLK_MMC2] = &mmc2_clk.common.hw,
+ [CLK_BUS_MMC0] = &bus_mmc0_clk.common.hw,
+ [CLK_BUS_MMC1] = &bus_mmc1_clk.common.hw,
+ [CLK_BUS_MMC2] = &bus_mmc2_clk.common.hw,
+ [CLK_BUS_UART0] = &bus_uart0_clk.common.hw,
+ [CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
+ [CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
+ [CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
+ [CLK_BUS_UART4] = &bus_uart4_clk.common.hw,
+ [CLK_BUS_I2C0] = &bus_i2c0_clk.common.hw,
+ [CLK_BUS_I2C1] = &bus_i2c1_clk.common.hw,
+ [CLK_BUS_I2C2] = &bus_i2c2_clk.common.hw,
+ [CLK_BUS_I2C3] = &bus_i2c3_clk.common.hw,
+ [CLK_SPI0] = &spi0_clk.common.hw,
+ [CLK_SPI1] = &spi1_clk.common.hw,
+ [CLK_SPI2] = &spi2_clk.common.hw,
+ [CLK_BUS_SPI0] = &bus_spi0_clk.common.hw,
+ [CLK_BUS_SPI1] = &bus_spi1_clk.common.hw,
+ [CLK_BUS_SPI2] = &bus_spi2_clk.common.hw,
+ [CLK_EMAC_25M] = &emac_25m_clk.common.hw,
+ [CLK_BUS_EMAC] = &bus_emac_clk.common.hw,
+ [CLK_IR_RX] = &ir_rx_clk.common.hw,
+ [CLK_BUS_IR_RX] = &bus_ir_rx_clk.common.hw,
+ [CLK_IR_TX] = &ir_tx_clk.common.hw,
+ [CLK_BUS_IR_TX] = &bus_ir_tx_clk.common.hw,
+ [CLK_BUS_GPADC] = &bus_gpadc_clk.common.hw,
+ [CLK_BUS_THS] = &bus_ths_clk.common.hw,
+ [CLK_I2S0] = &i2s0_clk.common.hw,
+ [CLK_I2S1] = &i2s1_clk.common.hw,
+ [CLK_I2S2] = &i2s2_clk.common.hw,
+ [CLK_I2S3] = &i2s3_clk.common.hw,
+ [CLK_BUS_I2S0] = &bus_i2s0_clk.common.hw,
+ [CLK_BUS_I2S1] = &bus_i2s1_clk.common.hw,
+ [CLK_BUS_I2S2] = &bus_i2s2_clk.common.hw,
+ [CLK_BUS_I2S3] = &bus_i2s3_clk.common.hw,
+ [CLK_SPDIF] = &spdif_clk.common.hw,
+ [CLK_BUS_SPDIF] = &bus_spdif_clk.common.hw,
+ [CLK_DMIC] = &dmic_clk.common.hw,
+ [CLK_BUS_DMIC] = &bus_dmic_clk.common.hw,
+ [CLK_AUDIO_DAC] = &audio_codec_dac_clk.common.hw,
+ [CLK_AUDIO_ADC] = &audio_codec_adc_clk.common.hw,
+ [CLK_AUDIO_4X] = &audio_codec_4x_clk.common.hw,
+ [CLK_BUS_AUDIO_CODEC] = &bus_audio_codec_clk.common.hw,
+ [CLK_USB_OHCI0] = &usb_ohci0_clk.common.hw,
+ [CLK_USB_PHY0] = &usb_phy0_clk.common.hw,
+ [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw,
+ [CLK_USB_PHY1] = &usb_phy1_clk.common.hw,
+ [CLK_BUS_OHCI0] = &bus_ohci0_clk.common.hw,
+ [CLK_BUS_OHCI1] = &bus_ohci1_clk.common.hw,
+ [CLK_BUS_EHCI0] = &bus_ehci0_clk.common.hw,
+ [CLK_BUS_EHCI1] = &bus_ehci1_clk.common.hw,
+ [CLK_BUS_OTG] = &bus_otg_clk.common.hw,
+ [CLK_BUS_LRADC] = &bus_lradc_clk.common.hw,
+ [CLK_BUS_DPSS_TOP0] = &bus_dpss_top0_clk.common.hw,
+ [CLK_BUS_DPSS_TOP1] = &bus_dpss_top1_clk.common.hw,
+ [CLK_MIPI_DSI] = &mipi_dsi_clk.common.hw,
+ [CLK_BUS_MIPI_DSI] = &bus_mipi_dsi_clk.common.hw,
+ [CLK_TCON_LCD] = &tcon_lcd_clk.common.hw,
+ [CLK_BUS_TCON_LCD] = &bus_tcon_lcd_clk.common.hw,
+ [CLK_LEDC] = &ledc_clk.common.hw,
+ [CLK_BUS_LEDC] = &bus_ledc_clk.common.hw,
+ [CLK_CSI_TOP] = &csi_top_clk.common.hw,
+ [CLK_CSI0_MCLK] = &csi0_mclk_clk.common.hw,
+ [CLK_CSI1_MCLK] = &csi1_mclk_clk.common.hw,
+ [CLK_BUS_CSI] = &bus_csi_clk.common.hw,
+ [CLK_CSI_ISP] = &csi_isp_clk.common.hw,
+ },
+ .num = CLK_NUMBER,
+};
+
+static struct ccu_reset_map sun50i_a100_ccu_resets[] = {
+ [RST_MBUS] = { 0x540, BIT(30) },
+
+ [RST_BUS_DE] = { 0x60c, BIT(16) },
+ [RST_BUS_G2D] = { 0x63c, BIT(16) },
+ [RST_BUS_GPU] = { 0x67c, BIT(16) },
+ [RST_BUS_CE] = { 0x68c, BIT(16) },
+ [RST_BUS_VE] = { 0x69c, BIT(16) },
+ [RST_BUS_DMA] = { 0x70c, BIT(16) },
+ [RST_BUS_MSGBOX] = { 0x71c, BIT(16) },
+ [RST_BUS_SPINLOCK] = { 0x72c, BIT(16) },
+ [RST_BUS_HSTIMER] = { 0x73c, BIT(16) },
+ [RST_BUS_DBG] = { 0x78c, BIT(16) },
+ [RST_BUS_PSI] = { 0x79c, BIT(16) },
+ [RST_BUS_PWM] = { 0x7ac, BIT(16) },
+ [RST_BUS_DRAM] = { 0x80c, BIT(16) },
+ [RST_BUS_NAND] = { 0x82c, BIT(16) },
+ [RST_BUS_MMC0] = { 0x84c, BIT(16) },
+ [RST_BUS_MMC1] = { 0x84c, BIT(17) },
+ [RST_BUS_MMC2] = { 0x84c, BIT(18) },
+ [RST_BUS_UART0] = { 0x90c, BIT(16) },
+ [RST_BUS_UART1] = { 0x90c, BIT(17) },
+ [RST_BUS_UART2] = { 0x90c, BIT(18) },
+ [RST_BUS_UART3] = { 0x90c, BIT(19) },
+ [RST_BUS_UART4] = { 0x90c, BIT(20) },
+ [RST_BUS_I2C0] = { 0x91c, BIT(16) },
+ [RST_BUS_I2C1] = { 0x91c, BIT(17) },
+ [RST_BUS_I2C2] = { 0x91c, BIT(18) },
+ [RST_BUS_I2C3] = { 0x91c, BIT(19) },
+ [RST_BUS_SPI0] = { 0x96c, BIT(16) },
+ [RST_BUS_SPI1] = { 0x96c, BIT(17) },
+ [RST_BUS_SPI2] = { 0x96c, BIT(18) },
+ [RST_BUS_EMAC] = { 0x97c, BIT(16) },
+ [RST_BUS_IR_RX] = { 0x99c, BIT(16) },
+ [RST_BUS_IR_TX] = { 0x9cc, BIT(16) },
+ [RST_BUS_GPADC] = { 0x9ec, BIT(16) },
+ [RST_BUS_THS] = { 0x9fc, BIT(16) },
+ [RST_BUS_I2S0] = { 0xa20, BIT(16) },
+ [RST_BUS_I2S1] = { 0xa20, BIT(17) },
+ [RST_BUS_I2S2] = { 0xa20, BIT(18) },
+ [RST_BUS_I2S3] = { 0xa20, BIT(19) },
+ [RST_BUS_SPDIF] = { 0xa2c, BIT(16) },
+ [RST_BUS_DMIC] = { 0xa4c, BIT(16) },
+ [RST_BUS_AUDIO_CODEC] = { 0xa5c, BIT(16) },
+
+ [RST_USB_PHY0] = { 0xa70, BIT(30) },
+ [RST_USB_PHY1] = { 0xa74, BIT(30) },
+
+ [RST_BUS_OHCI0] = { 0xa8c, BIT(16) },
+ [RST_BUS_OHCI1] = { 0xa8c, BIT(17) },
+ [RST_BUS_EHCI0] = { 0xa8c, BIT(20) },
+ [RST_BUS_EHCI1] = { 0xa8c, BIT(21) },
+ [RST_BUS_OTG] = { 0xa8c, BIT(24) },
+
+ [RST_BUS_LRADC] = { 0xa9c, BIT(16) },
+ [RST_BUS_DPSS_TOP0] = { 0xabc, BIT(16) },
+ [RST_BUS_DPSS_TOP1] = { 0xacc, BIT(16) },
+ [RST_BUS_MIPI_DSI] = { 0xb4c, BIT(16) },
+ [RST_BUS_TCON_LCD] = { 0xb7c, BIT(16) },
+ [RST_BUS_LVDS] = { 0xbac, BIT(16) },
+ [RST_BUS_LEDC] = { 0xbfc, BIT(16) },
+ [RST_BUS_CSI] = { 0xc1c, BIT(16) },
+ [RST_BUS_CSI_ISP] = { 0xc2c, BIT(16) },
+};
+
+static const struct sunxi_ccu_desc sun50i_a100_ccu_desc = {
+ .ccu_clks = sun50i_a100_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun50i_a100_ccu_clks),
+
+ .hw_clks = &sun50i_a100_hw_clks,
+
+ .resets = sun50i_a100_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun50i_a100_ccu_resets),
+};
+
+static const u32 sun50i_a100_pll_regs[] = {
+ SUN50I_A100_PLL_CPUX_REG,
+ SUN50I_A100_PLL_DDR0_REG,
+ SUN50I_A100_PLL_PERIPH0_REG,
+ SUN50I_A100_PLL_PERIPH1_REG,
+ SUN50I_A100_PLL_GPU_REG,
+ SUN50I_A100_PLL_VIDEO0_REG,
+ SUN50I_A100_PLL_VIDEO1_REG,
+ SUN50I_A100_PLL_VIDEO2_REG,
+ SUN50I_A100_PLL_VIDEO3_REG,
+ SUN50I_A100_PLL_VE_REG,
+ SUN50I_A100_PLL_COM_REG,
+ SUN50I_A100_PLL_AUDIO_REG,
+};
+
+static const u32 sun50i_a100_pll_video_regs[] = {
+ SUN50I_A100_PLL_VIDEO0_REG,
+ SUN50I_A100_PLL_VIDEO1_REG,
+ SUN50I_A100_PLL_VIDEO2_REG,
+ SUN50I_A100_PLL_VIDEO3_REG,
+};
+
+static const u32 sun50i_a100_usb2_clk_regs[] = {
+ SUN50I_A100_USB0_CLK_REG,
+ SUN50I_A100_USB1_CLK_REG,
+};
+
+static struct ccu_pll_nb sun50i_a100_pll_cpu_nb = {
+ .common = &pll_cpux_clk.common,
+ /* copy from pll_cpux_clk */
+ .enable = BIT(27),
+ .lock = BIT(28),
+};
+
+static struct ccu_mux_nb sun50i_a100_cpu_nb = {
+ .common = &cpux_clk.common,
+ .cm = &cpux_clk.mux,
+ .delay_us = 1,
+ .bypass_index = 4, /* index of pll periph0 */
+};
+
+static int sun50i_a100_ccu_probe(struct platform_device *pdev)
+{
+ void __iomem *reg;
+ u32 val;
+ int i, ret;
+
+ reg = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(reg))
+ return PTR_ERR(reg);
+
+ /*
+ * Enable lock and enable bits on all PLLs.
+ *
+ * Due to the current design, multiple PLLs share one power switch,
+ * so switching PLL is easy to cause stability problems.
+ * When initializing, we enable them by default. When disable,
+ * we only turn off the output of PLL.
+ */
+ for (i = 0; i < ARRAY_SIZE(sun50i_a100_pll_regs); i++) {
+ val = readl(reg + sun50i_a100_pll_regs[i]);
+ val |= SUN50I_A100_PLL_LOCK_ENABLE | SUN50I_A100_PLL_ENABLE;
+ writel(val, reg + sun50i_a100_pll_regs[i]);
+ }
+
+ /*
+ * In order to pass the EMI certification, the SDM function of
+ * the peripheral 1 bus is enabled, and the frequency is still
+ * calculated using the previous division factor.
+ */
+ writel(SUN50I_A100_PLL_PERIPH1_PATTERN0,
+ reg + SUN50I_A100_PLL_PERIPH1_PATTERN0_REG);
+
+ val = readl(reg + SUN50I_A100_PLL_PERIPH1_REG);
+ val |= SUN50I_A100_PLL_SDM_ENABLE;
+ writel(val, reg + SUN50I_A100_PLL_PERIPH1_REG);
+
+ /*
+ * Force the output divider of video PLLs to 0.
+ *
+ * See the comment before pll-video0 definition for the reason.
+ */
+ for (i = 0; i < ARRAY_SIZE(sun50i_a100_pll_video_regs); i++) {
+ val = readl(reg + sun50i_a100_pll_video_regs[i]);
+ val &= ~BIT(0);
+ writel(val, reg + sun50i_a100_pll_video_regs[i]);
+ }
+
+ /*
+ * Enforce m1 = 0, m0 = 1 for Audio PLL
+ *
+ * See the comment before pll-audio definition for the reason.
+ */
+ val = readl(reg + SUN50I_A100_PLL_AUDIO_REG);
+ val &= ~BIT(1);
+ val |= BIT(0);
+ writel(val, reg + SUN50I_A100_PLL_AUDIO_REG);
+
+ /*
+ * Force OHCI 12M clock sources to 00 (12MHz divided from 48MHz)
+ *
+ * This clock mux is still mysterious, and the code just enforces
+ * it to have a valid clock parent.
+ */
+ for (i = 0; i < ARRAY_SIZE(sun50i_a100_usb2_clk_regs); i++) {
+ val = readl(reg + sun50i_a100_usb2_clk_regs[i]);
+ val &= ~GENMASK(25, 24);
+ writel(val, reg + sun50i_a100_usb2_clk_regs[i]);
+ }
+
+ ret = sunxi_ccu_probe(pdev->dev.of_node, reg, &sun50i_a100_ccu_desc);
+ if (ret)
+ return ret;
+
+ /* Gate then ungate PLL CPU after any rate changes */
+ ccu_pll_notifier_register(&sun50i_a100_pll_cpu_nb);
+
+ /* Reparent CPU during PLL CPU rate changes */
+ ccu_mux_notifier_register(pll_cpux_clk.common.hw.clk,
+ &sun50i_a100_cpu_nb);
+
+ return 0;
+}
+
+static const struct of_device_id sun50i_a100_ccu_ids[] = {
+ { .compatible = "allwinner,sun50i-a100-ccu" },
+ { }
+};
+
+static struct platform_driver sun50i_a100_ccu_driver = {
+ .probe = sun50i_a100_ccu_probe,
+ .driver = {
+ .name = "sun50i-a100-ccu",
+ .of_match_table = sun50i_a100_ccu_ids,
+ },
+};
+module_platform_driver(sun50i_a100_ccu_driver);
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100.h b/drivers/clk/sunxi-ng/ccu-sun50i-a100.h
new file mode 100644
index 0000000..a599320
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100.h
@@ -0,0 +1,56 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2020 Frank Lee <frank@allwinnertech.com>
+ */
+
+#ifndef _CCU_SUN50I_A100_H_
+#define _CCU_SUN50I_A100_H_
+
+#include <dt-bindings/clock/sun50i-a100-ccu.h>
+#include <dt-bindings/reset/sun50i-a100-ccu.h>
+
+#define CLK_OSC12M 0
+#define CLK_PLL_CPUX 1
+#define CLK_PLL_DDR0 2
+
+/* PLL_PERIPH0 exported for PRCM */
+
+#define CLK_PLL_PERIPH0_2X 4
+#define CLK_PLL_PERIPH1 5
+#define CLK_PLL_PERIPH1_2X 6
+#define CLK_PLL_GPU 7
+#define CLK_PLL_VIDEO0 8
+#define CLK_PLL_VIDEO0_2X 9
+#define CLK_PLL_VIDEO0_4X 10
+#define CLK_PLL_VIDEO1 11
+#define CLK_PLL_VIDEO1_2X 12
+#define CLK_PLL_VIDEO1_4X 13
+#define CLK_PLL_VIDEO2 14
+#define CLK_PLL_VIDEO2_2X 15
+#define CLK_PLL_VIDEO2_4X 16
+#define CLK_PLL_VIDEO3 17
+#define CLK_PLL_VIDEO3_2X 18
+#define CLK_PLL_VIDEO3_4X 19
+#define CLK_PLL_VE 20
+#define CLK_PLL_COM 21
+#define CLK_PLL_COM_AUDIO 22
+#define CLK_PLL_AUDIO 23
+
+/* CPUX clock exported for DVFS */
+
+#define CLK_AXI 25
+#define CLK_CPUX_APB 26
+#define CLK_PSI_AHB1_AHB2 27
+#define CLK_AHB3 28
+
+/* APB1 clock exported for PIO */
+
+#define CLK_APB2 30
+
+/* All module clocks and bus gates are exported except DRAM */
+
+#define CLK_BUS_DRAM 58
+
+#define CLK_NUMBER (CLK_CSI_ISP + 1)
+
+#endif /* _CCU_SUN50I_A100_H_ */
diff --git a/include/dt-bindings/clock/sun50i-a100-ccu.h b/include/dt-bindings/clock/sun50i-a100-ccu.h
new file mode 100644
index 0000000..8cdf563
--- /dev/null
+++ b/include/dt-bindings/clock/sun50i-a100-ccu.h
@@ -0,0 +1,116 @@
+/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/*
+ * Copyright (c) 2020 Frank Lee <frank@allwinnertech.com>
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUN50I_A100_H_
+#define _DT_BINDINGS_CLK_SUN50I_A100_H_
+
+#define CLK_PLL_PERIPH0 3
+
+#define CLK_CPUX 24
+
+#define CLK_APB1 29
+
+#define CLK_MBUS 31
+#define CLK_DE 32
+#define CLK_BUS_DE 33
+#define CLK_G2D 34
+#define CLK_BUS_G2D 35
+#define CLK_GPU 36
+#define CLK_BUS_GPU 37
+#define CLK_CE 38
+#define CLK_BUS_CE 39
+#define CLK_VE 40
+#define CLK_BUS_VE 41
+#define CLK_BUS_DMA 42
+#define CLK_BUS_MSGBOX 43
+#define CLK_BUS_SPINLOCK 44
+#define CLK_BUS_HSTIMER 45
+#define CLK_AVS 46
+#define CLK_BUS_DBG 47
+#define CLK_BUS_PSI 48
+#define CLK_BUS_PWM 49
+#define CLK_BUS_IOMMU 50
+#define CLK_MBUS_DMA 51
+#define CLK_MBUS_VE 52
+#define CLK_MBUS_CE 53
+#define CLK_MBUS_NAND 54
+#define CLK_MBUS_CSI 55
+#define CLK_MBUS_ISP 56
+#define CLK_MBUS_G2D 57
+
+#define CLK_NAND0 59
+#define CLK_NAND1 60
+#define CLK_BUS_NAND 61
+#define CLK_MMC0 62
+#define CLK_MMC1 63
+#define CLK_MMC2 64
+#define CLK_MMC3 65
+#define CLK_BUS_MMC0 66
+#define CLK_BUS_MMC1 67
+#define CLK_BUS_MMC2 68
+#define CLK_BUS_UART0 69
+#define CLK_BUS_UART1 70
+#define CLK_BUS_UART2 71
+#define CLK_BUS_UART3 72
+#define CLK_BUS_UART4 73
+#define CLK_BUS_I2C0 74
+#define CLK_BUS_I2C1 75
+#define CLK_BUS_I2C2 76
+#define CLK_BUS_I2C3 77
+#define CLK_SPI0 78
+#define CLK_SPI1 79
+#define CLK_SPI2 80
+#define CLK_BUS_SPI0 81
+#define CLK_BUS_SPI1 82
+#define CLK_BUS_SPI2 83
+#define CLK_EMAC_25M 84
+#define CLK_BUS_EMAC 85
+#define CLK_IR_RX 86
+#define CLK_BUS_IR_RX 87
+#define CLK_IR_TX 88
+#define CLK_BUS_IR_TX 89
+#define CLK_BUS_GPADC 90
+#define CLK_BUS_THS 91
+#define CLK_I2S0 92
+#define CLK_I2S1 93
+#define CLK_I2S2 94
+#define CLK_I2S3 95
+#define CLK_BUS_I2S0 96
+#define CLK_BUS_I2S1 97
+#define CLK_BUS_I2S2 98
+#define CLK_BUS_I2S3 99
+#define CLK_SPDIF 100
+#define CLK_BUS_SPDIF 101
+#define CLK_DMIC 102
+#define CLK_BUS_DMIC 103
+#define CLK_AUDIO_DAC 104
+#define CLK_AUDIO_ADC 105
+#define CLK_AUDIO_4X 106
+#define CLK_BUS_AUDIO_CODEC 107
+#define CLK_USB_OHCI0 108
+#define CLK_USB_PHY0 109
+#define CLK_USB_OHCI1 110
+#define CLK_USB_PHY1 111
+#define CLK_BUS_OHCI0 112
+#define CLK_BUS_OHCI1 113
+#define CLK_BUS_EHCI0 114
+#define CLK_BUS_EHCI1 115
+#define CLK_BUS_OTG 116
+#define CLK_BUS_LRADC 117
+#define CLK_BUS_DPSS_TOP0 118
+#define CLK_BUS_DPSS_TOP1 119
+#define CLK_MIPI_DSI 120
+#define CLK_BUS_MIPI_DSI 121
+#define CLK_TCON_LCD 122
+#define CLK_BUS_TCON_LCD 123
+#define CLK_LEDC 124
+#define CLK_BUS_LEDC 125
+#define CLK_CSI_TOP 126
+#define CLK_CSI0_MCLK 127
+#define CLK_CSI1_MCLK 128
+#define CLK_BUS_CSI 129
+#define CLK_CSI_ISP 130
+
+#endif /* _DT_BINDINGS_CLK_SUN50I_A100_H_ */
diff --git a/include/dt-bindings/clock/sun50i-a100-r-ccu.h b/include/dt-bindings/clock/sun50i-a100-r-ccu.h
new file mode 100644
index 0000000..8a6cc5c
--- /dev/null
+++ b/include/dt-bindings/clock/sun50i-a100-r-ccu.h
@@ -0,0 +1,23 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2020 Frank Lee <frank@allwinnertech.com>
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUN50I_A100_R_CCU_H_
+#define _DT_BINDINGS_CLK_SUN50I_A100_R_CCU_H_
+
+#define CLK_R_APB1 2
+
+#define CLK_R_APB1_TIMER 4
+#define CLK_R_APB1_TWD 5
+#define CLK_R_APB1_PWM 6
+#define CLK_R_APB1_BUS_PWM 7
+#define CLK_R_APB1_PPU 8
+#define CLK_R_APB2_UART 9
+#define CLK_R_APB2_I2C0 10
+#define CLK_R_APB2_I2C1 11
+#define CLK_R_APB1_IR 12
+#define CLK_R_APB1_BUS_IR 13
+#define CLK_R_AHB_BUS_RTC 14
+
+#endif /* _DT_BINDINGS_CLK_SUN50I_A100_R_CCU_H_ */
diff --git a/include/dt-bindings/reset/sun50i-a100-ccu.h b/include/dt-bindings/reset/sun50i-a100-ccu.h
new file mode 100644
index 0000000..17b8b66
--- /dev/null
+++ b/include/dt-bindings/reset/sun50i-a100-ccu.h
@@ -0,0 +1,68 @@
+/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/*
+ * Copyright (c) 2020 Frank Lee <frank@allwinnertech.com>
+ */
+
+#ifndef _DT_BINDINGS_RESET_SUN50I_A100_H_
+#define _DT_BINDINGS_RESET_SUN50I_A100_H_
+
+#define RST_MBUS 0
+#define RST_BUS_DE 1
+#define RST_BUS_G2D 2
+#define RST_BUS_GPU 3
+#define RST_BUS_CE 4
+#define RST_BUS_VE 5
+#define RST_BUS_DMA 6
+#define RST_BUS_MSGBOX 7
+#define RST_BUS_SPINLOCK 8
+#define RST_BUS_HSTIMER 9
+#define RST_BUS_DBG 10
+#define RST_BUS_PSI 11
+#define RST_BUS_PWM 12
+#define RST_BUS_DRAM 13
+#define RST_BUS_NAND 14
+#define RST_BUS_MMC0 15
+#define RST_BUS_MMC1 16
+#define RST_BUS_MMC2 17
+#define RST_BUS_UART0 18
+#define RST_BUS_UART1 19
+#define RST_BUS_UART2 20
+#define RST_BUS_UART3 21
+#define RST_BUS_UART4 22
+#define RST_BUS_I2C0 23
+#define RST_BUS_I2C1 24
+#define RST_BUS_I2C2 25
+#define RST_BUS_I2C3 26
+#define RST_BUS_SPI0 27
+#define RST_BUS_SPI1 28
+#define RST_BUS_SPI2 29
+#define RST_BUS_EMAC 30
+#define RST_BUS_IR_RX 31
+#define RST_BUS_IR_TX 32
+#define RST_BUS_GPADC 33
+#define RST_BUS_THS 34
+#define RST_BUS_I2S0 35
+#define RST_BUS_I2S1 36
+#define RST_BUS_I2S2 37
+#define RST_BUS_I2S3 38
+#define RST_BUS_SPDIF 39
+#define RST_BUS_DMIC 40
+#define RST_BUS_AUDIO_CODEC 41
+#define RST_USB_PHY0 42
+#define RST_USB_PHY1 43
+#define RST_BUS_OHCI0 44
+#define RST_BUS_OHCI1 45
+#define RST_BUS_EHCI0 46
+#define RST_BUS_EHCI1 47
+#define RST_BUS_OTG 48
+#define RST_BUS_LRADC 49
+#define RST_BUS_DPSS_TOP0 50
+#define RST_BUS_DPSS_TOP1 51
+#define RST_BUS_MIPI_DSI 52
+#define RST_BUS_TCON_LCD 53
+#define RST_BUS_LVDS 54
+#define RST_BUS_LEDC 55
+#define RST_BUS_CSI 56
+#define RST_BUS_CSI_ISP 57
+
+#endif /* _DT_BINDINGS_RESET_SUN50I_A100_H_ */
diff --git a/include/dt-bindings/reset/sun50i-a100-r-ccu.h b/include/dt-bindings/reset/sun50i-a100-r-ccu.h
new file mode 100644
index 0000000..2bf1ed4
--- /dev/null
+++ b/include/dt-bindings/reset/sun50i-a100-r-ccu.h
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/*
+ * Copyright (c) 2020 Frank Lee <frank@allwinnertech.com>
+ */
+
+#ifndef _DT_BINDINGS_RST_SUN50I_A100_R_CCU_H_
+#define _DT_BINDINGS_RST_SUN50I_A100_R_CCU_H_
+
+#define RST_R_APB1_TIMER 0
+#define RST_R_APB1_BUS_PWM 1
+#define RST_R_APB1_PPU 2
+#define RST_R_APB2_UART 3
+#define RST_R_APB2_I2C0 4
+#define RST_R_APB2_I2C1 5
+#define RST_R_APB1_BUS_IR 6
+#define RST_R_AHB_BUS_RTC 7
+
+#endif /* _DT_BINDINGS_RST_SUN50I_A100_R_CCU_H_ */
--
1.9.1
^ permalink raw reply related [flat|nested] 26+ messages in thread* [PATCH v3 03/16] dt-bindings: pinctrl: sunxi: Add A100 pinctrl bindings
2020-07-08 7:19 [PATCH v3 00/16] Allwinner A100 Initial support Frank Lee
2020-07-08 7:19 ` [PATCH v3 01/16] dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and R-CCU Frank Lee
2020-07-08 7:19 ` [PATCH v3 02/16] clk: sunxi-ng: add support for the Allwinner A100 CCU Frank Lee
@ 2020-07-08 7:19 ` Frank Lee
2020-07-13 23:01 ` Rob Herring
2020-07-08 7:19 ` [PATCH v3 04/16] dt-bindings: pinctrl: sunxi: make gpio banks supplies required Frank Lee
` (8 subsequent siblings)
11 siblings, 1 reply; 26+ messages in thread
From: Frank Lee @ 2020-07-08 7:19 UTC (permalink / raw)
To: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, clabbe, icenowy, megous, stefan, bage
Cc: devicetree, linux-arm-kernel, linux-kernel, linux-clk, linux-i2c,
linux-gpio, linux-pm, huangshuosheng, liyong, Frank Lee
Add device tree binding Documentation details for A100 pinctrl driver,
whic has an r pin controller and a pin controller with more irq lines.
Signed-off-by: Frank Lee <frank@allwinnertech.com>
---
.../pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 74 +++++++++++++---------
1 file changed, 44 insertions(+), 30 deletions(-)
diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
index bfefd09..226aba0 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
@@ -48,6 +48,8 @@ properties:
- allwinner,sun9i-a80-r-pinctrl
- allwinner,sun50i-a64-pinctrl
- allwinner,sun50i-a64-r-pinctrl
+ - allwinner,sun50i-a100-pinctrl
+ - allwinner,sun50i-a100-r-pinctrl
- allwinner,sun50i-h5-pinctrl
- allwinner,sun50i-h6-pinctrl
- allwinner,sun50i-h6-r-pinctrl
@@ -59,7 +61,7 @@ properties:
interrupts:
minItems: 1
- maxItems: 5
+ maxItems: 7
description:
One interrupt per external interrupt bank supported on the
controller, sorted by bank number ascending order.
@@ -144,75 +146,87 @@ allOf:
# FIXME: We should have the pin bank supplies here, but not a lot of
# boards are defining it at the moment so it would generate a lot of
# warnings.
-
- if:
properties:
compatible:
enum:
- - allwinner,sun9i-a80-pinctrl
+ - allwinner,sun50i-a100-pinctrl
then:
properties:
interrupts:
- minItems: 5
- maxItems: 5
+ minItems: 7
+ maxItems: 7
else:
if:
properties:
compatible:
enum:
- - allwinner,sun6i-a31-pinctrl
- - allwinner,sun6i-a31s-pinctrl
- - allwinner,sun50i-h6-pinctrl
+ - allwinner,sun9i-a80-pinctrl
then:
properties:
interrupts:
- minItems: 4
- maxItems: 4
+ minItems: 5
+ maxItems: 5
else:
if:
properties:
compatible:
enum:
- - allwinner,sun8i-a23-pinctrl
- - allwinner,sun8i-a83t-pinctrl
- - allwinner,sun50i-a64-pinctrl
- - allwinner,sun50i-h5-pinctrl
- - allwinner,suniv-f1c100s-pinctrl
+ - allwinner,sun6i-a31-pinctrl
+ - allwinner,sun6i-a31s-pinctrl
+ - allwinner,sun50i-h6-pinctrl
then:
properties:
interrupts:
- minItems: 3
- maxItems: 3
+ minItems: 4
+ maxItems: 4
else:
if:
properties:
compatible:
enum:
- - allwinner,sun6i-a31-r-pinctrl
- - allwinner,sun8i-a33-pinctrl
- - allwinner,sun8i-h3-pinctrl
- - allwinner,sun8i-v3-pinctrl
- - allwinner,sun8i-v3s-pinctrl
- - allwinner,sun9i-a80-r-pinctrl
- - allwinner,sun50i-h6-r-pinctrl
+ - allwinner,sun8i-a23-pinctrl
+ - allwinner,sun8i-a83t-pinctrl
+ - allwinner,sun50i-a64-pinctrl
+ - allwinner,sun50i-h5-pinctrl
+ - allwinner,suniv-f1c100s-pinctrl
then:
properties:
interrupts:
- minItems: 2
- maxItems: 2
+ minItems: 3
+ maxItems: 3
else:
- properties:
- interrupts:
- minItems: 1
- maxItems: 1
+ if:
+ properties:
+ compatible:
+ enum:
+ - allwinner,sun6i-a31-r-pinctrl
+ - allwinner,sun8i-a33-pinctrl
+ - allwinner,sun8i-h3-pinctrl
+ - allwinner,sun8i-v3-pinctrl
+ - allwinner,sun8i-v3s-pinctrl
+ - allwinner,sun9i-a80-r-pinctrl
+ - allwinner,sun50i-h6-r-pinctrl
+
+ then:
+ properties:
+ interrupts:
+ minItems: 2
+ maxItems: 2
+
+ else:
+ properties:
+ interrupts:
+ minItems: 1
+ maxItems: 1
additionalProperties: false
--
1.9.1
^ permalink raw reply related [flat|nested] 26+ messages in thread* Re: [PATCH v3 03/16] dt-bindings: pinctrl: sunxi: Add A100 pinctrl bindings
2020-07-08 7:19 ` [PATCH v3 03/16] dt-bindings: pinctrl: sunxi: Add A100 pinctrl bindings Frank Lee
@ 2020-07-13 23:01 ` Rob Herring
0 siblings, 0 replies; 26+ messages in thread
From: Rob Herring @ 2020-07-13 23:01 UTC (permalink / raw)
To: Frank Lee
Cc: mripard, wens, mturquette, sboyd, gregory.clement, tglx, jason,
maz, srinivas.kandagatla, linus.walleij, anarsoul, tiny.windzz,
rui.zhang, daniel.lezcano, amit.kucheria, lee.jones, p.zabel,
clabbe, icenowy, megous, stefan, bage, devicetree,
linux-arm-kernel, linux-kernel, linux-clk, linux-i2c, linux-gpio,
linux-pm, huangshuosheng, liyong
On Wed, Jul 08, 2020 at 03:19:29PM +0800, Frank Lee wrote:
> Add device tree binding Documentation details for A100 pinctrl driver,
> whic has an r pin controller and a pin controller with more irq lines.
s/whic/which/
'an r pin controller'?
>
> Signed-off-by: Frank Lee <frank@allwinnertech.com>
> ---
> .../pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 74 +++++++++++++---------
> 1 file changed, 44 insertions(+), 30 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> index bfefd09..226aba0 100644
> --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> @@ -48,6 +48,8 @@ properties:
> - allwinner,sun9i-a80-r-pinctrl
> - allwinner,sun50i-a64-pinctrl
> - allwinner,sun50i-a64-r-pinctrl
> + - allwinner,sun50i-a100-pinctrl
> + - allwinner,sun50i-a100-r-pinctrl
> - allwinner,sun50i-h5-pinctrl
> - allwinner,sun50i-h6-pinctrl
> - allwinner,sun50i-h6-r-pinctrl
> @@ -59,7 +61,7 @@ properties:
>
> interrupts:
> minItems: 1
> - maxItems: 5
> + maxItems: 7
> description:
> One interrupt per external interrupt bank supported on the
> controller, sorted by bank number ascending order.
> @@ -144,75 +146,87 @@ allOf:
> # FIXME: We should have the pin bank supplies here, but not a lot of
> # boards are defining it at the moment so it would generate a lot of
> # warnings.
> -
> - if:
> properties:
> compatible:
> enum:
> - - allwinner,sun9i-a80-pinctrl
> + - allwinner,sun50i-a100-pinctrl
>
> then:
> properties:
> interrupts:
> - minItems: 5
> - maxItems: 5
> + minItems: 7
> + maxItems: 7
>
> else:
> if:
This diff is hard to follow. Rather than a continual nesting of 'else'
clauses, just make each 'if' a new entry under 'allOf' and get rid of
the else. Perhaps do that in a separate patch first, then this change
will be easier to review.
> properties:
> compatible:
> enum:
> - - allwinner,sun6i-a31-pinctrl
> - - allwinner,sun6i-a31s-pinctrl
> - - allwinner,sun50i-h6-pinctrl
> + - allwinner,sun9i-a80-pinctrl
>
> then:
> properties:
> interrupts:
> - minItems: 4
> - maxItems: 4
> + minItems: 5
> + maxItems: 5
>
> else:
> if:
> properties:
> compatible:
> enum:
> - - allwinner,sun8i-a23-pinctrl
> - - allwinner,sun8i-a83t-pinctrl
> - - allwinner,sun50i-a64-pinctrl
> - - allwinner,sun50i-h5-pinctrl
> - - allwinner,suniv-f1c100s-pinctrl
> + - allwinner,sun6i-a31-pinctrl
> + - allwinner,sun6i-a31s-pinctrl
> + - allwinner,sun50i-h6-pinctrl
>
> then:
> properties:
> interrupts:
> - minItems: 3
> - maxItems: 3
> + minItems: 4
> + maxItems: 4
>
> else:
> if:
> properties:
> compatible:
> enum:
> - - allwinner,sun6i-a31-r-pinctrl
> - - allwinner,sun8i-a33-pinctrl
> - - allwinner,sun8i-h3-pinctrl
> - - allwinner,sun8i-v3-pinctrl
> - - allwinner,sun8i-v3s-pinctrl
> - - allwinner,sun9i-a80-r-pinctrl
> - - allwinner,sun50i-h6-r-pinctrl
> + - allwinner,sun8i-a23-pinctrl
> + - allwinner,sun8i-a83t-pinctrl
> + - allwinner,sun50i-a64-pinctrl
> + - allwinner,sun50i-h5-pinctrl
> + - allwinner,suniv-f1c100s-pinctrl
>
> then:
> properties:
> interrupts:
> - minItems: 2
> - maxItems: 2
> + minItems: 3
> + maxItems: 3
>
> else:
> - properties:
> - interrupts:
> - minItems: 1
> - maxItems: 1
> + if:
> + properties:
> + compatible:
> + enum:
> + - allwinner,sun6i-a31-r-pinctrl
> + - allwinner,sun8i-a33-pinctrl
> + - allwinner,sun8i-h3-pinctrl
> + - allwinner,sun8i-v3-pinctrl
> + - allwinner,sun8i-v3s-pinctrl
> + - allwinner,sun9i-a80-r-pinctrl
> + - allwinner,sun50i-h6-r-pinctrl
> +
> + then:
> + properties:
> + interrupts:
> + minItems: 2
> + maxItems: 2
> +
> + else:
> + properties:
> + interrupts:
> + minItems: 1
> + maxItems: 1
>
> additionalProperties: false
>
> --
> 1.9.1
>
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH v3 04/16] dt-bindings: pinctrl: sunxi: make gpio banks supplies required
2020-07-08 7:19 [PATCH v3 00/16] Allwinner A100 Initial support Frank Lee
` (2 preceding siblings ...)
2020-07-08 7:19 ` [PATCH v3 03/16] dt-bindings: pinctrl: sunxi: Add A100 pinctrl bindings Frank Lee
@ 2020-07-08 7:19 ` Frank Lee
2020-07-09 16:52 ` Rob Herring
` (2 more replies)
2020-07-08 7:19 ` [PATCH v3 05/16] pinctrl: sunxi: add support for the Allwinner A100 pin controller Frank Lee
` (7 subsequent siblings)
11 siblings, 3 replies; 26+ messages in thread
From: Frank Lee @ 2020-07-08 7:19 UTC (permalink / raw)
To: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, clabbe, icenowy, megous, stefan, bage
Cc: devicetree, linux-arm-kernel, linux-kernel, linux-clk, linux-i2c,
linux-gpio, linux-pm, huangshuosheng, liyong, Frank Lee
Since we don't really have to care about the existing DT for boards,
it would be great to make the gpio banks supplies required.
Signed-off-by: Frank Lee <frank@allwinnertech.com>
---
.../devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
index 226aba0..c30a7b7 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
@@ -134,6 +134,7 @@ patternProperties:
required:
- "#gpio-cells"
- "#interrupt-cells"
+ - "^vcc-p[a-hlm]-supply$"
- compatible
- reg
- interrupts
--
1.9.1
^ permalink raw reply related [flat|nested] 26+ messages in thread* Re: [PATCH v3 04/16] dt-bindings: pinctrl: sunxi: make gpio banks supplies required
2020-07-08 7:19 ` [PATCH v3 04/16] dt-bindings: pinctrl: sunxi: make gpio banks supplies required Frank Lee
@ 2020-07-09 16:52 ` Rob Herring
2020-07-09 16:54 ` Rob Herring
2020-07-09 17:17 ` Ondřej Jirman
2 siblings, 0 replies; 26+ messages in thread
From: Rob Herring @ 2020-07-09 16:52 UTC (permalink / raw)
To: Frank Lee
Cc: gregory.clement, megous, anarsoul, tiny.windzz, sboyd, jason,
robh+dt, maz, wens, lee.jones, mripard, amit.kucheria, linux-i2c,
icenowy, linux-gpio, srinivas.kandagatla, linux-pm,
daniel.lezcano, liyong, huangshuosheng, linus.walleij,
devicetree, linux-clk, bage, linux-arm-kernel, mturquette,
rui.zhang, tglx, clabbe, linux-kernel, p.zabel, stefan
On Wed, 08 Jul 2020 15:19:30 +0800, Frank Lee wrote:
> Since we don't really have to care about the existing DT for boards,
> it would be great to make the gpio banks supplies required.
>
> Signed-off-by: Frank Lee <frank@allwinnertech.com>
> ---
> .../devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 1 +
> 1 file changed, 1 insertion(+)
>
My bot found errors running 'make dt_binding_check' on your patch:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml: required:2: '^vcc-p[a-hlm]-supply$' does not match '^([a-zA-Z#][a-zA-Z0-9,+\\-._@]{0,63}|\\$nodename)$'
Documentation/devicetree/bindings/Makefile:20: recipe for target 'Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.example.dts' failed
make[1]: *** [Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.example.dts] Error 1
make[1]: *** Waiting for unfinished jobs....
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml: ignoring, error in schema: required: 2
warning: no schema found in file: ./Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml: ignoring, error in schema: required: 2
warning: no schema found in file: ./Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
Makefile:1347: recipe for target 'dt_binding_check' failed
make: *** [dt_binding_check] Error 2
See https://patchwork.ozlabs.org/patch/1325057
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure dt-schema is up to date:
pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
Please check and re-submit.
^ permalink raw reply [flat|nested] 26+ messages in thread* Re: [PATCH v3 04/16] dt-bindings: pinctrl: sunxi: make gpio banks supplies required
2020-07-08 7:19 ` [PATCH v3 04/16] dt-bindings: pinctrl: sunxi: make gpio banks supplies required Frank Lee
2020-07-09 16:52 ` Rob Herring
@ 2020-07-09 16:54 ` Rob Herring
2020-07-09 17:17 ` Ondřej Jirman
2 siblings, 0 replies; 26+ messages in thread
From: Rob Herring @ 2020-07-09 16:54 UTC (permalink / raw)
To: Frank Lee
Cc: mripard, wens, mturquette, sboyd, gregory.clement, tglx, jason,
maz, srinivas.kandagatla, linus.walleij, anarsoul, tiny.windzz,
rui.zhang, daniel.lezcano, amit.kucheria, lee.jones, p.zabel,
clabbe, icenowy, megous, stefan, bage, devicetree,
linux-arm-kernel, linux-kernel, linux-clk, linux-i2c, linux-gpio,
linux-pm, huangshuosheng, liyong
On Wed, Jul 08, 2020 at 03:19:30PM +0800, Frank Lee wrote:
> Since we don't really have to care about the existing DT for boards,
> it would be great to make the gpio banks supplies required.
>
> Signed-off-by: Frank Lee <frank@allwinnertech.com>
> ---
> .../devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> index 226aba0..c30a7b7 100644
> --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> @@ -134,6 +134,7 @@ patternProperties:
> required:
> - "#gpio-cells"
> - "#interrupt-cells"
> + - "^vcc-p[a-hlm]-supply$"
Patterns aren't supported here. It's something the json-schema folks
are working on. For now, You have to list out the specific properties.
> - compatible
> - reg
> - interrupts
> --
> 1.9.1
>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v3 04/16] dt-bindings: pinctrl: sunxi: make gpio banks supplies required
2020-07-08 7:19 ` [PATCH v3 04/16] dt-bindings: pinctrl: sunxi: make gpio banks supplies required Frank Lee
2020-07-09 16:52 ` Rob Herring
2020-07-09 16:54 ` Rob Herring
@ 2020-07-09 17:17 ` Ondřej Jirman
2020-07-10 12:37 ` Maxime Ripard
2 siblings, 1 reply; 26+ messages in thread
From: Ondřej Jirman @ 2020-07-09 17:17 UTC (permalink / raw)
To: Frank Lee
Cc: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, clabbe, icenowy, stefan, bage, devicetree, linux-pm,
liyong, linux-kernel, linux-gpio, huangshuosheng, linux-i2c,
linux-clk, linux-arm-kernel
Hello,
On Wed, Jul 08, 2020 at 03:19:30PM +0800, Frank Lee wrote:
> Since we don't really have to care about the existing DT for boards,
> it would be great to make the gpio banks supplies required.
What if the borad doesn't use one of the banks? How would
I describe such a board if defining supplies for all banks
is required?
regards,
o.
> Signed-off-by: Frank Lee <frank@allwinnertech.com>
> ---
> .../devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> index 226aba0..c30a7b7 100644
> --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> @@ -134,6 +134,7 @@ patternProperties:
> required:
> - "#gpio-cells"
> - "#interrupt-cells"
> + - "^vcc-p[a-hlm]-supply$"
> - compatible
> - reg
> - interrupts
> --
> 1.9.1
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v3 04/16] dt-bindings: pinctrl: sunxi: make gpio banks supplies required
2020-07-09 17:17 ` Ondřej Jirman
@ 2020-07-10 12:37 ` Maxime Ripard
2020-07-13 2:32 ` Frank Lee
0 siblings, 1 reply; 26+ messages in thread
From: Maxime Ripard @ 2020-07-10 12:37 UTC (permalink / raw)
To: Ondřej Jirman, Frank Lee, robh+dt, wens, mturquette, sboyd,
gregory.clement, tglx, jason, maz, srinivas.kandagatla,
linus.walleij, anarsoul, tiny.windzz, rui.zhang, daniel.lezcano,
amit.kucheria, lee.jones, p.zabel, clabbe, icenowy, stefan, bage,
devicetree, linux-pm, liyong, linux-kernel, linux-gpio,
huangshuosheng, linux-i2c, linux-clk, linux-arm-kernel
Hi,
On Thu, Jul 09, 2020 at 07:17:13PM +0200, Ondřej Jirman wrote:
> Hello,
>
> On Wed, Jul 08, 2020 at 03:19:30PM +0800, Frank Lee wrote:
> > Since we don't really have to care about the existing DT for boards,
> > it would be great to make the gpio banks supplies required.
>
> What if the borad doesn't use one of the banks? How would
> I describe such a board if defining supplies for all banks
> is required?
If that case ever comes up, we can always drop the requirement, it's going to be backward
compatible.
Maxime
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v3 04/16] dt-bindings: pinctrl: sunxi: make gpio banks supplies required
2020-07-10 12:37 ` Maxime Ripard
@ 2020-07-13 2:32 ` Frank Lee
0 siblings, 0 replies; 26+ messages in thread
From: Frank Lee @ 2020-07-13 2:32 UTC (permalink / raw)
To: Ondřej Jirman, robh+dt, wens, mturquette, sboyd,
gregory.clement, tglx, jason, maz, srinivas.kandagatla,
linus.walleij, anarsoul, tiny.windzz, rui.zhang, daniel.lezcano,
amit.kucheria, lee.jones, p.zabel, clabbe, icenowy, stefan, bage,
devicetree, linux-pm, 李勇,
linux-kernel, linux-gpio, 黄烁生,
linux-i2c, linux-clk, linux-arm-kernel, Maxime Ripard
Maybe we put this work backwards and let a100 join the mainline as soon as possible.
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH v3 05/16] pinctrl: sunxi: add support for the Allwinner A100 pin controller
2020-07-08 7:19 [PATCH v3 00/16] Allwinner A100 Initial support Frank Lee
` (3 preceding siblings ...)
2020-07-08 7:19 ` [PATCH v3 04/16] dt-bindings: pinctrl: sunxi: make gpio banks supplies required Frank Lee
@ 2020-07-08 7:19 ` Frank Lee
2020-07-08 7:19 ` [PATCH v3 06/16] dt-bindings: nvmem: SID: add binding for A100's SID controller Frank Lee
` (6 subsequent siblings)
11 siblings, 0 replies; 26+ messages in thread
From: Frank Lee @ 2020-07-08 7:19 UTC (permalink / raw)
To: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, clabbe, icenowy, megous, stefan, bage
Cc: devicetree, linux-arm-kernel, linux-kernel, linux-clk, linux-i2c,
linux-gpio, linux-pm, huangshuosheng, liyong, Frank Lee
This commit introduces support for the pin controller on A100.
Signed-off-by: Frank Lee <frank@allwinnertech.com>
---
drivers/pinctrl/sunxi/Kconfig | 10 +
drivers/pinctrl/sunxi/Makefile | 2 +
drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c | 105 ++++
drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c | 708 ++++++++++++++++++++++++++
4 files changed, 825 insertions(+)
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c
diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
index f7aae20..5932935 100644
--- a/drivers/pinctrl/sunxi/Kconfig
+++ b/drivers/pinctrl/sunxi/Kconfig
@@ -94,6 +94,16 @@ config PINCTRL_SUN50I_A64_R
default ARM64 && ARCH_SUNXI
select PINCTRL_SUNXI
+config PINCTRL_SUN50I_A100
+ bool "Support for the Allwinner A100 PIO"
+ default ARM64 && ARCH_SUNXI
+ select PINCTRL_SUNXI
+
+config PINCTRL_SUN50I_A100_R
+ bool "Support for the Allwinner A100 R-PIO"
+ default ARM64 && ARCH_SUNXI
+ select PINCTRL_SUNXI
+
config PINCTRL_SUN50I_H5
bool "Support for the Allwinner H5 PIO"
default ARM64 && ARCH_SUNXI
diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
index fafcdae..8b7ff0d 100644
--- a/drivers/pinctrl/sunxi/Makefile
+++ b/drivers/pinctrl/sunxi/Makefile
@@ -13,6 +13,8 @@ obj-$(CONFIG_PINCTRL_SUN8I_A23_R) += pinctrl-sun8i-a23-r.o
obj-$(CONFIG_PINCTRL_SUN8I_A33) += pinctrl-sun8i-a33.o
obj-$(CONFIG_PINCTRL_SUN50I_A64) += pinctrl-sun50i-a64.o
obj-$(CONFIG_PINCTRL_SUN50I_A64_R) += pinctrl-sun50i-a64-r.o
+obj-$(CONFIG_PINCTRL_SUN50I_A100) += pinctrl-sun50i-a100.o
+obj-$(CONFIG_PINCTRL_SUN50I_A100_R) += pinctrl-sun50i-a100-r.o
obj-$(CONFIG_PINCTRL_SUN8I_A83T) += pinctrl-sun8i-a83t.o
obj-$(CONFIG_PINCTRL_SUN8I_A83T_R) += pinctrl-sun8i-a83t-r.o
obj-$(CONFIG_PINCTRL_SUN8I_H3) += pinctrl-sun8i-h3.o
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c b/drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c
new file mode 100644
index 0000000..165674f
--- /dev/null
+++ b/drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c
@@ -0,0 +1,105 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020 Frank Lee <frank@allwinnertech.com>
+ *
+ * Based on:
+ * huangshuosheng <huangshuosheng@allwinnertech.com>
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/platform_device.h>
+
+#include "pinctrl-sunxi.h"
+
+static const struct sunxi_desc_pin a100_r_pins[] = {
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_i2c0"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_i2c0"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_uart0"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_uart0"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_jtag"), /* MS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_jtag"), /* CK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_jtag"), /* DO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_jtag"), /* DI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_i2c1"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_i2c1"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_pwm"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "s_cir"), /* IN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 11)),
+};
+
+static const struct sunxi_pinctrl_desc a100_r_pinctrl_data = {
+ .pins = a100_r_pins,
+ .npins = ARRAY_SIZE(a100_r_pins),
+ .pin_base = PL_BASE,
+ .irq_banks = 1,
+};
+
+static int a100_r_pinctrl_probe(struct platform_device *pdev)
+{
+ return sunxi_pinctrl_init(pdev, &a100_r_pinctrl_data);
+}
+
+static const struct of_device_id a100_r_pinctrl_match[] = {
+ { .compatible = "allwinner,sun50i-a100-r-pinctrl", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, a100_r_pinctrl_match);
+
+static struct platform_driver a100_r_pinctrl_driver = {
+ .probe = a100_r_pinctrl_probe,
+ .driver = {
+ .name = "sun50iw10p1-r-pinctrl",
+ .of_match_table = a100_r_pinctrl_match,
+ },
+};
+module_platform_driver(a100_r_pinctrl_driver);
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c b/drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c
new file mode 100644
index 0000000..c5fe85f
--- /dev/null
+++ b/drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c
@@ -0,0 +1,708 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020 Frank Lee <frank@allwinnertech.com>
+ *
+ * Based on:
+ * huangshuosheng <huangshuosheng@allwinnertech.com>
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/platform_device.h>
+
+#include "pinctrl-sunxi.h"
+
+static const struct sunxi_desc_pin a100_pins[] = {
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* TX */
+ SUNXI_FUNCTION(0x3, "spi2"), /* CS */
+ SUNXI_FUNCTION(0x4, "jtag"), /* MS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RX */
+ SUNXI_FUNCTION(0x3, "spi2"), /* CLK */
+ SUNXI_FUNCTION(0x4, "jtag"), /* CK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RTS */
+ SUNXI_FUNCTION(0x3, "spi2"), /* MOSI */
+ SUNXI_FUNCTION(0x4, "jtag"), /* DO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* CTS */
+ SUNXI_FUNCTION(0x3, "spi2"), /* MISO */
+ SUNXI_FUNCTION(0x4, "jtag"), /* DI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c1"), /* SCK */
+ SUNXI_FUNCTION(0x3, "i2s0"), /* MCLK */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* MS_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c1"), /* SDA */
+ SUNXI_FUNCTION(0x3, "i2s0"), /* BCLK */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* CK_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s0"), /* LRCK */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* DO_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spdif"), /* DIN */
+ SUNXI_FUNCTION(0x3, "i2s0_dout0"), /* DOUT0 */
+ SUNXI_FUNCTION(0x4, "i2s0_din1"), /* DIN1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spdif"), /* DOUT */
+ SUNXI_FUNCTION(0x3, "i2s0_din0"), /* DIN0 */
+ SUNXI_FUNCTION(0x4, "i2s0_dout1"), /* DOUT1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart0"), /* TX */
+ SUNXI_FUNCTION(0x3, "i2c0"), /* SCK */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* DI_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart0"), /* RX */
+ SUNXI_FUNCTION(0x3, "i2c0"), /* SDA */
+ SUNXI_FUNCTION(0x4, "pwm1"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)),
+ /* HOLE */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* WE */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* DS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* ALE */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* RST */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CLE */
+ SUNXI_FUNCTION(0x4, "spi0"), /* MOSI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CE1 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* CS0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CE0 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* MISO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RE */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RB0 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* CMD */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RB1 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* CS1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ7 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ6 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D4 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 9)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ5 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 10)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ4 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D5 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 11)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQS */
+ SUNXI_FUNCTION(0x4, "spi0"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 12)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ3 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 13)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ2 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D6 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 14)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ1 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D2 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* WP */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 15)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ0 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D7 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* HOLD */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 16)),
+ /* HOLE */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D2 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* D0P */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DP0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D3 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* D0N */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DM0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D4 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* D1P */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DP1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D5 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* D1N */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DM1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D6 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* D2P */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* CKP */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D7 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* D2N */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* CKM */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D10 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* CKP */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DP2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D11 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* CKN */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DM2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D12 */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DP3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D13 */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DM3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 9)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D14 */
+ SUNXI_FUNCTION(0x4, "spi1"), /* CS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 10)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D15 */
+ SUNXI_FUNCTION(0x4, "spi1"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 11)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D18 */
+ SUNXI_FUNCTION(0x4, "spi1"), /* MOSI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 12)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D19 */
+ SUNXI_FUNCTION(0x4, "spi1"), /* MISO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 13)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D20 */
+ SUNXI_FUNCTION(0x4, "uart3"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 14)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D21 */
+ SUNXI_FUNCTION(0x4, "uart3"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 15)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D22 */
+ SUNXI_FUNCTION(0x4, "uart3"), /* RTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 16)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 17),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D23 */
+ SUNXI_FUNCTION(0x4, "uart3"), /* CTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 17)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 18),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* CLK */
+ SUNXI_FUNCTION(0x4, "uart4"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 18)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 19),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* DE */
+ SUNXI_FUNCTION(0x4, "uart4"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 19)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 20),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* HSYNC */
+ SUNXI_FUNCTION(0x3, "pwm2"),
+ SUNXI_FUNCTION(0x4, "uart4"), /* RTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 20)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 21),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* VSYNC */
+ SUNXI_FUNCTION(0x3, "pwm3"),
+ SUNXI_FUNCTION(0x4, "uart4"), /* CTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 21)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 22),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "pwm1"),
+ SUNXI_FUNCTION(0x4, "i2c0"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 22)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 23),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "pwm0"),
+ SUNXI_FUNCTION(0x4, "i2c0"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 23)),
+ /* HOLE */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* MCLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c2"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c2"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c3"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c3"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* MCLK */
+ SUNXI_FUNCTION(0x3, "pll"), /* LOCK_DBG */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* MCLK */
+ SUNXI_FUNCTION(0x5, "ledc"), /* LEDC */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "bist0"), /* RESULT0 */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* BCLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* SM_VS */
+ SUNXI_FUNCTION(0x3, "bist0"), /* RESULT1 */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* LRCK */
+ SUNXI_FUNCTION(0x5, "tcon0"), /* TRIG */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "bist0"), /* RESULT2 */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* DOUT0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "bist0"), /* RESULT3 */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* DIN0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 9)),
+ /* HOLE */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D1 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* MS1 */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* MS_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D0 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DI1 */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* DI_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* CLK */
+ SUNXI_FUNCTION(0x3, "uart0"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* CMD */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DO */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* DO_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D3 */
+ SUNXI_FUNCTION(0x3, "uart0"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D2 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* CK */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* CK_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 6)),
+ /* HOLE */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* CMD */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* RTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* CTS */
+ SUNXI_FUNCTION(0x3, "i2s1"), /* MCLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 9)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s1"), /* BCLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 10)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s1"), /* LRCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 11)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s1_dout0"), /* DOUT0 */
+ SUNXI_FUNCTION(0x4, "i2s1_din1"), /* DIN1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 12)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s1_din0"), /* DIN0 */
+ SUNXI_FUNCTION(0x4, "i2s1_dout1"), /* DOUT1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 13)),
+ /* HOLE */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c0"), /* SCK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* RXD1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c0"), /* SDA */
+ SUNXI_FUNCTION(0x5, "emac0"), /* RXD0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c1"), /* SCK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* RXCTL */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c1"), /* SDA */
+ SUNXI_FUNCTION(0x3, "cir0"), /* OUT */
+ SUNXI_FUNCTION(0x5, "emac0"), /* CLKIN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart3"), /* TX */
+ SUNXI_FUNCTION(0x3, "spi1"), /* CS */
+ SUNXI_FUNCTION(0x5, "emac0"), /* TXD1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart3"), /* RX */
+ SUNXI_FUNCTION(0x3, "spi1"), /* CLK */
+ SUNXI_FUNCTION(0x4, "ledc"),
+ SUNXI_FUNCTION(0x5, "emac0"), /* TXD0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart3"), /* RTS */
+ SUNXI_FUNCTION(0x3, "spi1"), /* MOSI */
+ SUNXI_FUNCTION(0x5, "emac0"), /* TXCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart3"), /* CTS */
+ SUNXI_FUNCTION(0x3, "spi1"), /* MISO */
+ SUNXI_FUNCTION(0x4, "spdif"), /* OUT */
+ SUNXI_FUNCTION(0x5, "emac0"), /* TXCTL */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "dmic"), /* CLK */
+ SUNXI_FUNCTION(0x3, "spi2"), /* CS */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* MCLK */
+ SUNXI_FUNCTION(0x5, "i2s2_din2"), /* DIN2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "dmic"), /* DATA0 */
+ SUNXI_FUNCTION(0x3, "spi2"), /* CLK */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* BCLK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* MDC */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 9)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "dmic"), /* DATA1 */
+ SUNXI_FUNCTION(0x3, "spi2"), /* MOSI */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* LRCK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* MDIO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 10)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "dmic"), /* DATA2 */
+ SUNXI_FUNCTION(0x3, "spi2"), /* MISO */
+ SUNXI_FUNCTION(0x4, "i2s2_dout0"), /* DOUT0 */
+ SUNXI_FUNCTION(0x5, "i2s2_din1"), /* DIN1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 11)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "dmic"), /* DATA3 */
+ SUNXI_FUNCTION(0x3, "i2c3"), /* SCK */
+ SUNXI_FUNCTION(0x4, "i2s2_din0"), /* DIN0 */
+ SUNXI_FUNCTION(0x5, "i2s2_dout1"), /* DOUT1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 12)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2c3"), /* SCK */
+ SUNXI_FUNCTION(0x4, "i2s3"), /* MCLK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* EPHY */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 13)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x4, "i2s3"), /* BCLK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* RXD3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 14)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x4, "i2s3"), /* LRCK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* RXD2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 15)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s3_dout0"), /* DOUT0 */
+ SUNXI_FUNCTION(0x4, "i2s3_din1"), /* DIN1 */
+ SUNXI_FUNCTION(0x5, "emac0"), /* RXCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 16)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 17),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s3_dout1"), /* DOUT1 */
+ SUNXI_FUNCTION(0x4, "i2s3_din0"), /* DIN0 */
+ SUNXI_FUNCTION(0x5, "emac0"), /* TXD3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 17)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 18),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "cir0"), /* OUT */
+ SUNXI_FUNCTION(0x3, "i2s3_dout2"), /* DOUT2 */
+ SUNXI_FUNCTION(0x4, "i2s3_din2"), /* DIN2 */
+ SUNXI_FUNCTION(0x5, "emac0"), /* TXD2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 18)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 19),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "cir0"), /* IN */
+ SUNXI_FUNCTION(0x3, "i2s3_dout3"), /* DOUT3 */
+ SUNXI_FUNCTION(0x4, "i2s3_din3"), /* DIN3 */
+ SUNXI_FUNCTION(0x5, "ledc"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 19)),
+};
+
+static const unsigned int a100_irq_bank_map[] = { 0, 1, 2, 3, 4, 5, 6};
+
+static const struct sunxi_pinctrl_desc a100_pinctrl_data = {
+ .pins = a100_pins,
+ .npins = ARRAY_SIZE(a100_pins),
+ .irq_banks = 7,
+ .irq_bank_map = a100_irq_bank_map,
+ .io_bias_cfg_variant = BIAS_VOLTAGE_PIO_POW_MODE_SEL,
+};
+
+static int a100_pinctrl_probe(struct platform_device *pdev)
+{
+ return sunxi_pinctrl_init(pdev, &a100_pinctrl_data);
+}
+
+static const struct of_device_id a100_pinctrl_match[] = {
+ { .compatible = "allwinner,sun50i-a100-pinctrl", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, a100_pinctrl_match);
+
+static struct platform_driver a100_pinctrl_driver = {
+ .probe = a100_pinctrl_probe,
+ .driver = {
+ .name = "sun50i-a100-pinctrl",
+ .of_match_table = a100_pinctrl_match,
+ },
+};
+module_platform_driver(a100_pinctrl_driver);
--
1.9.1
^ permalink raw reply related [flat|nested] 26+ messages in thread* [PATCH v3 06/16] dt-bindings: nvmem: SID: add binding for A100's SID controller
2020-07-08 7:19 [PATCH v3 00/16] Allwinner A100 Initial support Frank Lee
` (4 preceding siblings ...)
2020-07-08 7:19 ` [PATCH v3 05/16] pinctrl: sunxi: add support for the Allwinner A100 pin controller Frank Lee
@ 2020-07-08 7:19 ` Frank Lee
2020-07-09 16:54 ` Rob Herring
2020-07-08 7:19 ` [PATCH v3 07/16] dt-bindings: thermal: sun8i: Add binding for A100's THS controller Frank Lee
` (5 subsequent siblings)
11 siblings, 1 reply; 26+ messages in thread
From: Frank Lee @ 2020-07-08 7:19 UTC (permalink / raw)
To: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, clabbe, icenowy, megous, stefan, bage
Cc: devicetree, linux-arm-kernel, linux-kernel, linux-clk, linux-i2c,
linux-gpio, linux-pm, huangshuosheng, liyong, Frank Lee
Add a binding for A100's SID controller.
Signed-off-by: Frank Lee <frank@allwinnertech.com>
---
Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml | 3 +++
1 file changed, 3 insertions(+)
diff --git a/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml b/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml
index daf1321..f9d575b 100644
--- a/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml
+++ b/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml
@@ -21,6 +21,9 @@ properties:
- allwinner,sun8i-a83t-sid
- allwinner,sun8i-h3-sid
- allwinner,sun50i-a64-sid
+ - items:
+ - const: allwinner,sun50i-a100-sid
+ - const: allwinner,sun50i-a64-sid
- allwinner,sun50i-h5-sid
- allwinner,sun50i-h6-sid
--
1.9.1
^ permalink raw reply related [flat|nested] 26+ messages in thread* Re: [PATCH v3 06/16] dt-bindings: nvmem: SID: add binding for A100's SID controller
2020-07-08 7:19 ` [PATCH v3 06/16] dt-bindings: nvmem: SID: add binding for A100's SID controller Frank Lee
@ 2020-07-09 16:54 ` Rob Herring
0 siblings, 0 replies; 26+ messages in thread
From: Rob Herring @ 2020-07-09 16:54 UTC (permalink / raw)
To: Frank Lee
Cc: linux-gpio, amit.kucheria, linux-arm-kernel, gregory.clement,
linux-clk, robh+dt, huangshuosheng, devicetree, daniel.lezcano,
wens, lee.jones, clabbe, p.zabel, icenowy, tiny.windzz,
linux-kernel, jason, liyong, linux-i2c, bage, stefan,
linus.walleij, rui.zhang, tglx, megous, linux-pm, mripard,
anarsoul, mturquette, srinivas.kandagatla, maz, sboyd
On Wed, 08 Jul 2020 15:19:32 +0800, Frank Lee wrote:
> Add a binding for A100's SID controller.
>
> Signed-off-by: Frank Lee <frank@allwinnertech.com>
> ---
> Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml | 3 +++
> 1 file changed, 3 insertions(+)
>
My bot found errors running 'make dt_binding_check' on your patch:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml: properties:compatible:enum:5: {'items': [{'const': 'allwinner,sun50i-a100-sid'}, {'const': 'allwinner,sun50i-a64-sid'}]} is not of type 'string'
Documentation/devicetree/bindings/Makefile:20: recipe for target 'Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.example.dts' failed
make[1]: *** [Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.example.dts] Error 1
make[1]: *** Waiting for unfinished jobs....
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml: ignoring, error in schema: properties: compatible: enum: 5
warning: no schema found in file: ./Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml: ignoring, error in schema: properties: compatible: enum: 5
warning: no schema found in file: ./Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml
Makefile:1347: recipe for target 'dt_binding_check' failed
make: *** [dt_binding_check] Error 2
See https://patchwork.ozlabs.org/patch/1325053
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure dt-schema is up to date:
pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
Please check and re-submit.
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH v3 07/16] dt-bindings: thermal: sun8i: Add binding for A100's THS controller
2020-07-08 7:19 [PATCH v3 00/16] Allwinner A100 Initial support Frank Lee
` (5 preceding siblings ...)
2020-07-08 7:19 ` [PATCH v3 06/16] dt-bindings: nvmem: SID: add binding for A100's SID controller Frank Lee
@ 2020-07-08 7:19 ` Frank Lee
2020-07-13 23:02 ` Rob Herring
2020-07-08 7:19 ` [PATCH v3 08/16] thermal: sun8i: add TEMP_CALIB_MASK for calibration data in sun50i_h6_ths_calibrate Frank Lee
` (4 subsequent siblings)
11 siblings, 1 reply; 26+ messages in thread
From: Frank Lee @ 2020-07-08 7:19 UTC (permalink / raw)
To: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, clabbe, icenowy, megous, stefan, bage
Cc: devicetree, linux-arm-kernel, linux-kernel, linux-clk, linux-i2c,
linux-gpio, linux-pm, huangshuosheng, liyong, Frank Lee
Add a binding for A100's ths controller.
Signed-off-by: Frank Lee <frank@allwinnertech.com>
Reviewed-by: Yangtao Li <tiny.windzz@gmail.com>
---
.../devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml | 6 +++++-
1 file changed, 5 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml b/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml
index 8736926..9d40fc7 100644
--- a/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml
+++ b/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml
@@ -17,6 +17,7 @@ properties:
- allwinner,sun8i-h3-ths
- allwinner,sun8i-r40-ths
- allwinner,sun50i-a64-ths
+ - allwinner,sun50i-a100-ths
- allwinner,sun50i-h5-ths
- allwinner,sun50i-h6-ths
@@ -61,7 +62,9 @@ allOf:
properties:
compatible:
contains:
- const: allwinner,sun50i-h6-ths
+ enum:
+ - allwinner,sun50i-a100-ths
+ - allwinner,sun50i-h6-ths
then:
properties:
@@ -103,6 +106,7 @@ allOf:
- const: allwinner,sun8i-h3-ths
- const: allwinner,sun8i-r40-ths
- const: allwinner,sun50i-a64-ths
+ - const: allwinner,sun50i-a100-ths
- const: allwinner,sun50i-h5-ths
- const: allwinner,sun50i-h6-ths
--
1.9.1
^ permalink raw reply related [flat|nested] 26+ messages in thread* Re: [PATCH v3 07/16] dt-bindings: thermal: sun8i: Add binding for A100's THS controller
2020-07-08 7:19 ` [PATCH v3 07/16] dt-bindings: thermal: sun8i: Add binding for A100's THS controller Frank Lee
@ 2020-07-13 23:02 ` Rob Herring
0 siblings, 0 replies; 26+ messages in thread
From: Rob Herring @ 2020-07-13 23:02 UTC (permalink / raw)
To: Frank Lee
Cc: mturquette, devicetree, linux-i2c, mripard, lee.jones, sboyd,
liyong, daniel.lezcano, anarsoul, linux-kernel, linus.walleij,
megous, linux-arm-kernel, linux-clk, rui.zhang,
srinivas.kandagatla, linux-pm, gregory.clement, icenowy,
tiny.windzz, jason, stefan, maz, tglx, wens, bage,
huangshuosheng, amit.kucheria, p.zabel, robh+dt, clabbe,
linux-gpio
On Wed, 08 Jul 2020 15:19:33 +0800, Frank Lee wrote:
> Add a binding for A100's ths controller.
>
> Signed-off-by: Frank Lee <frank@allwinnertech.com>
> Reviewed-by: Yangtao Li <tiny.windzz@gmail.com>
> ---
> .../devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml | 6 +++++-
> 1 file changed, 5 insertions(+), 1 deletion(-)
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH v3 08/16] thermal: sun8i: add TEMP_CALIB_MASK for calibration data in sun50i_h6_ths_calibrate
2020-07-08 7:19 [PATCH v3 00/16] Allwinner A100 Initial support Frank Lee
` (6 preceding siblings ...)
2020-07-08 7:19 ` [PATCH v3 07/16] dt-bindings: thermal: sun8i: Add binding for A100's THS controller Frank Lee
@ 2020-07-08 7:19 ` Frank Lee
2020-07-08 7:19 ` [PATCH v3 09/16] thermal: sun8i: Add A100's THS controller support Frank Lee
` (3 subsequent siblings)
11 siblings, 0 replies; 26+ messages in thread
From: Frank Lee @ 2020-07-08 7:19 UTC (permalink / raw)
To: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, clabbe, icenowy, megous, stefan, bage
Cc: devicetree, linux-arm-kernel, linux-kernel, linux-clk, linux-i2c,
linux-gpio, linux-pm, huangshuosheng, liyong, Frank Lee
For sun50i_h6_ths_calibrate(), the data read from nvmem needs a round of
calculation. On the other hand, the newer SOC may store other data in
the space other than 12bit sensor data. Add mask operation to read data
to avoid conversion error.
Signed-off-by: Frank Lee <frank@allwinnertech.com>
Reviewed-by: Yangtao Li <tiny.windzz@gmail.com>
---
drivers/thermal/sun8i_thermal.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c
index 74d73be..f423d44 100644
--- a/drivers/thermal/sun8i_thermal.c
+++ b/drivers/thermal/sun8i_thermal.c
@@ -244,7 +244,7 @@ static int sun50i_h6_ths_calibrate(struct ths_device *tmdev,
ft_temp = (caldata[0] & FT_TEMP_MASK) * 100;
for (i = 0; i < tmdev->chip->sensor_num; i++) {
- int sensor_reg = caldata[i + 1];
+ int sensor_reg = caldata[i + 1] & TEMP_CALIB_MASK;
int cdata, offset;
int sensor_temp = tmdev->chip->calc_temp(tmdev, i, sensor_reg);
--
1.9.1
^ permalink raw reply related [flat|nested] 26+ messages in thread* [PATCH v3 09/16] thermal: sun8i: Add A100's THS controller support
2020-07-08 7:19 [PATCH v3 00/16] Allwinner A100 Initial support Frank Lee
` (7 preceding siblings ...)
2020-07-08 7:19 ` [PATCH v3 08/16] thermal: sun8i: add TEMP_CALIB_MASK for calibration data in sun50i_h6_ths_calibrate Frank Lee
@ 2020-07-08 7:19 ` Frank Lee
2020-07-08 7:19 ` [PATCH v3 10/16] mfd: axp20x: Allow the AXP803 to be probed by I2C Frank Lee
` (2 subsequent siblings)
11 siblings, 0 replies; 26+ messages in thread
From: Frank Lee @ 2020-07-08 7:19 UTC (permalink / raw)
To: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, clabbe, icenowy, megous, stefan, bage
Cc: devicetree, linux-arm-kernel, linux-kernel, linux-clk, linux-i2c,
linux-gpio, linux-pm, huangshuosheng, liyong, Frank Lee
This patch add thermal sensor controller support for A100,
which is similar to the previous ones.
Signed-off-by: Frank Lee <frank@allwinnertech.com>
Reviewed-by: Yangtao Li <tiny.windzz@gmail.com>
---
drivers/thermal/sun8i_thermal.c | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c
index f423d44..f8b1307 100644
--- a/drivers/thermal/sun8i_thermal.c
+++ b/drivers/thermal/sun8i_thermal.c
@@ -590,6 +590,19 @@ static int sun8i_ths_remove(struct platform_device *pdev)
.calc_temp = sun8i_ths_calc_temp,
};
+static const struct ths_thermal_chip sun50i_a100_ths = {
+ .sensor_num = 3,
+ .has_bus_clk_reset = true,
+ .ft_deviation = 8000,
+ .offset = 187744,
+ .scale = 672,
+ .temp_data_base = SUN50I_H6_THS_TEMP_DATA,
+ .calibrate = sun50i_h6_ths_calibrate,
+ .init = sun50i_h6_thermal_init,
+ .irq_ack = sun50i_h6_irq_ack,
+ .calc_temp = sun8i_ths_calc_temp,
+};
+
static const struct ths_thermal_chip sun50i_h5_ths = {
.sensor_num = 2,
.has_mod_clk = true,
@@ -619,6 +632,7 @@ static int sun8i_ths_remove(struct platform_device *pdev)
{ .compatible = "allwinner,sun8i-h3-ths", .data = &sun8i_h3_ths },
{ .compatible = "allwinner,sun8i-r40-ths", .data = &sun8i_r40_ths },
{ .compatible = "allwinner,sun50i-a64-ths", .data = &sun50i_a64_ths },
+ { .compatible = "allwinner,sun50i-a100-ths", .data = &sun50i_a100_ths },
{ .compatible = "allwinner,sun50i-h5-ths", .data = &sun50i_h5_ths },
{ .compatible = "allwinner,sun50i-h6-ths", .data = &sun50i_h6_ths },
{ /* sentinel */ },
--
1.9.1
^ permalink raw reply related [flat|nested] 26+ messages in thread* [PATCH v3 10/16] mfd: axp20x: Allow the AXP803 to be probed by I2C
2020-07-08 7:19 [PATCH v3 00/16] Allwinner A100 Initial support Frank Lee
` (8 preceding siblings ...)
2020-07-08 7:19 ` [PATCH v3 09/16] thermal: sun8i: Add A100's THS controller support Frank Lee
@ 2020-07-08 7:19 ` Frank Lee
2020-07-16 15:10 ` Lee Jones
2020-07-08 7:45 ` [PATCH v3 00/16] Allwinner A100 Initial support Corentin Labbe
2020-07-10 14:28 ` Maxime Ripard
11 siblings, 1 reply; 26+ messages in thread
From: Frank Lee @ 2020-07-08 7:19 UTC (permalink / raw)
To: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, clabbe, icenowy, megous, stefan, bage
Cc: devicetree, linux-arm-kernel, linux-kernel, linux-clk, linux-i2c,
linux-gpio, linux-pm, huangshuosheng, liyong, Frank Lee
The AXP803 can be used both using the RSB proprietary bus, or a more
traditional I2C bus.
Let's add that possibility.
Signed-off-by: Frank Lee <frank@allwinnertech.com>
---
drivers/mfd/axp20x-i2c.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/mfd/axp20x-i2c.c b/drivers/mfd/axp20x-i2c.c
index 14f9df7..446a7d0 100644
--- a/drivers/mfd/axp20x-i2c.c
+++ b/drivers/mfd/axp20x-i2c.c
@@ -63,6 +63,7 @@ static int axp20x_i2c_remove(struct i2c_client *i2c)
{ .compatible = "x-powers,axp209", .data = (void *)AXP209_ID },
{ .compatible = "x-powers,axp221", .data = (void *)AXP221_ID },
{ .compatible = "x-powers,axp223", .data = (void *)AXP223_ID },
+ { .compatible = "x-powers,axp803", .data = (void *)AXP803_ID },
{ .compatible = "x-powers,axp806", .data = (void *)AXP806_ID },
{ },
};
@@ -74,6 +75,7 @@ static int axp20x_i2c_remove(struct i2c_client *i2c)
{ "axp209", 0 },
{ "axp221", 0 },
{ "axp223", 0 },
+ { "axp803", 0 },
{ "axp806", 0 },
{ },
};
--
1.9.1
^ permalink raw reply related [flat|nested] 26+ messages in thread* Re: [PATCH v3 10/16] mfd: axp20x: Allow the AXP803 to be probed by I2C
2020-07-08 7:19 ` [PATCH v3 10/16] mfd: axp20x: Allow the AXP803 to be probed by I2C Frank Lee
@ 2020-07-16 15:10 ` Lee Jones
0 siblings, 0 replies; 26+ messages in thread
From: Lee Jones @ 2020-07-16 15:10 UTC (permalink / raw)
To: Frank Lee
Cc: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, p.zabel,
clabbe, icenowy, megous, stefan, bage, devicetree,
linux-arm-kernel, linux-kernel, linux-clk, linux-i2c, linux-gpio,
linux-pm, huangshuosheng, liyong
On Wed, 08 Jul 2020, Frank Lee wrote:
> The AXP803 can be used both using the RSB proprietary bus, or a more
> traditional I2C bus.
>
> Let's add that possibility.
>
> Signed-off-by: Frank Lee <frank@allwinnertech.com>
> ---
> drivers/mfd/axp20x-i2c.c | 2 ++
> 1 file changed, 2 insertions(+)
Applied, thanks.
--
Lee Jones [李琼斯]
Senior Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v3 00/16] Allwinner A100 Initial support
2020-07-08 7:19 [PATCH v3 00/16] Allwinner A100 Initial support Frank Lee
` (9 preceding siblings ...)
2020-07-08 7:19 ` [PATCH v3 10/16] mfd: axp20x: Allow the AXP803 to be probed by I2C Frank Lee
@ 2020-07-08 7:45 ` Corentin Labbe
2020-07-13 2:41 ` Frank Lee
2020-07-10 14:28 ` Maxime Ripard
11 siblings, 1 reply; 26+ messages in thread
From: Corentin Labbe @ 2020-07-08 7:45 UTC (permalink / raw)
To: Frank Lee
Cc: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, clabbe, icenowy, megous, stefan, bage, devicetree,
linux-pm, liyong, linux-kernel, linux-gpio, huangshuosheng,
linux-i2c, linux-clk, linux-arm-kernel
On Wed, Jul 08, 2020 at 03:19:26PM +0800, Frank Lee wrote:
> This patch set adds initial support for allwinner a100 soc,
> which is a 64-bit tablet chip.
>
Hello
Does a product already exists with it ? I couldnt found any.
Does a datasheet is availlable ?
Regards
^ permalink raw reply [flat|nested] 26+ messages in thread* Re: [PATCH v3 00/16] Allwinner A100 Initial support
2020-07-08 7:45 ` [PATCH v3 00/16] Allwinner A100 Initial support Corentin Labbe
@ 2020-07-13 2:41 ` Frank Lee
0 siblings, 0 replies; 26+ messages in thread
From: Frank Lee @ 2020-07-13 2:41 UTC (permalink / raw)
To: Corentin Labbe
Cc: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, clabbe, icenowy, megous, stefan, bage, devicetree,
linux-pm, 李勇,
linux-kernel, linux-gpio, 黄烁生,
linux-i2c, linux-clk, linux-arm-kernel
> On Wed, Jul 08, 2020 at 03:19:26PM +0800, Frank Lee wrote:
>> This patch set adds initial support for allwinner a100 soc,
>> which is a 64-bit tablet chip.
> >
>
> Hello
>
> Does a product already exists with it ? I couldnt found any.
> Does a datasheet is availlable ?
>
The product is still in development, A133 is actually a high performance version of A100.
Yangtao
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v3 00/16] Allwinner A100 Initial support
2020-07-08 7:19 [PATCH v3 00/16] Allwinner A100 Initial support Frank Lee
` (10 preceding siblings ...)
2020-07-08 7:45 ` [PATCH v3 00/16] Allwinner A100 Initial support Corentin Labbe
@ 2020-07-10 14:28 ` Maxime Ripard
2020-07-13 2:39 ` Frank Lee
11 siblings, 1 reply; 26+ messages in thread
From: Maxime Ripard @ 2020-07-10 14:28 UTC (permalink / raw)
To: Frank Lee
Cc: robh+dt, wens, mturquette, sboyd, gregory.clement, tglx, jason,
maz, srinivas.kandagatla, linus.walleij, anarsoul, tiny.windzz,
rui.zhang, daniel.lezcano, amit.kucheria, lee.jones, p.zabel,
clabbe, icenowy, megous, stefan, bage, devicetree,
linux-arm-kernel, linux-kernel, linux-clk, linux-i2c, linux-gpio,
linux-pm, huangshuosheng, liyong
Hi,
On Wed, Jul 08, 2020 at 03:19:26PM +0800, Frank Lee wrote:
> This patch set adds initial support for allwinner a100 soc,
> which is a 64-bit tablet chip.
>
> v3:
> -Add pmu and nmi support
> -Add read data mask for calibration
> -Code style
> -Some trivial things in yaml files
>
> v2:
> -Some naming consistency
> -Repair email address
> -Fix mmc clock
> -Don't export system clock
> -Fix checkpatch warning
> -Drop unneeded pin function, convert to jtag_gpu and i2s_x
>
> Frank Lee (16):
> dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and
> R-CCU
> clk: sunxi-ng: add support for the Allwinner A100 CCU
> dt-bindings: pinctrl: sunxi: Add A100 pinctrl bindings
> dt-bindings: pinctrl: sunxi: make gpio banks supplies required
> pinctrl: sunxi: add support for the Allwinner A100 pin controller
> dt-bindings: nvmem: SID: add binding for A100's SID controller
> dt-bindings: thermal: sun8i: Add binding for A100's THS controller
> thermal: sun8i: add TEMP_CALIB_MASK for calibration data in
> sun50i_h6_ths_calibrate
> thermal: sun8i: Add A100's THS controller support
> mfd: axp20x: Allow the AXP803 to be probed by I2C
> dt-bindings: irq: sun7i-nmi: fix dt-binding for a80 nmi
> dt-bindings: irq: sun7i-nmi: Add binding for A100's NMI controller
it doesn't look like those patches went through?
> dt-bindings: i2c: mv64xxx: Add compatible for the A100 i2c node.
> arm64: allwinner: A100: add the basical Allwinner A100 DTSI file
> dt-bindings: arm: sunxi: Add Allwinner A100 Perf1 Board bindings
> arm64: allwinner: A100: add support for Allwinner Perf1 board
On a more general topic, which bootloader have you used to test this?
The one from Allwinner's BSP I assume?
Maxime
^ permalink raw reply [flat|nested] 26+ messages in thread* Re: [PATCH v3 00/16] Allwinner A100 Initial support
2020-07-10 14:28 ` Maxime Ripard
@ 2020-07-13 2:39 ` Frank Lee
0 siblings, 0 replies; 26+ messages in thread
From: Frank Lee @ 2020-07-13 2:39 UTC (permalink / raw)
To: Maxime Ripard
Cc: robh+dt, wens, mturquette, sboyd, gregory.clement, tglx, jason,
maz, srinivas.kandagatla, linus.walleij, anarsoul, tiny.windzz,
rui.zhang, daniel.lezcano, amit.kucheria, lee.jones, p.zabel,
clabbe, icenowy, megous, stefan, bage, devicetree,
linux-arm-kernel, linux-kernel, linux-clk, linux-i2c, linux-gpio,
linux-pm, 黄烁生, 李勇
HI,
>> dt-bindings: irq: sun7i-nmi: fix dt-binding for a80 nmi
>> dt-bindings: irq: sun7i-nmi: Add binding for A100's NMI controller
>
>it doesn't look like those patches went through?
Due to sending too many emails at once, it seems that some emails have
been filtered by the mailbox, and I just reissued them.
>
>> dt-bindings: i2c: mv64xxx: Add compatible for the A100 i2c node.
>> arm64: allwinner: A100: add the basical Allwinner A100 DTSI file
>> dt-bindings: arm: sunxi: Add Allwinner A100 Perf1 Board bindings
>> arm64: allwinner: A100: add support for Allwinner Perf1 board
>
>On a more general topic, which bootloader have you used to test this?
>The one from Allwinner's BSP I assume?
Yeah, there is no bringup on the mainline BootLoader yet.
If nothing happens, the next edition will be released today.
We hope that A100 will be integrated as soon as possible.
MBR,
Yangtao
^ permalink raw reply [flat|nested] 26+ messages in thread