* [PATCH v11 1/7] RISC-V: Clear SIP bit only when using SBI IPI operations
2022-11-14 9:38 [PATCH v11 0/7] RISC-V IPI Improvements Anup Patel
@ 2022-11-14 9:38 ` Anup Patel
2022-11-14 9:38 ` [PATCH v11 2/7] irqchip/riscv-intc: Allow drivers to directly discover INTC hwnode Anup Patel
` (5 subsequent siblings)
6 siblings, 0 replies; 12+ messages in thread
From: Anup Patel @ 2022-11-14 9:38 UTC (permalink / raw)
To: Palmer Dabbelt, Paul Walmsley, Thomas Gleixner, Marc Zyngier,
Daniel Lezcano
Cc: Atish Patra, Alistair Francis, Anup Patel, linux-riscv,
linux-kernel, Anup Patel, Bin Meng, Atish Patra
The software interrupt pending (i.e. [M|S]SIP) bit is writeable for
S-mode but read-only for M-mode so we clear this bit only when using
SBI IPI operations.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
---
arch/riscv/kernel/sbi.c | 8 +++++++-
arch/riscv/kernel/smp.c | 2 --
2 files changed, 7 insertions(+), 3 deletions(-)
diff --git a/arch/riscv/kernel/sbi.c b/arch/riscv/kernel/sbi.c
index 775d3322b422..fc614650a2e3 100644
--- a/arch/riscv/kernel/sbi.c
+++ b/arch/riscv/kernel/sbi.c
@@ -643,8 +643,14 @@ static void sbi_send_cpumask_ipi(const struct cpumask *target)
sbi_send_ipi(target);
}
+static void sbi_ipi_clear(void)
+{
+ csr_clear(CSR_IP, IE_SIE);
+}
+
static const struct riscv_ipi_ops sbi_ipi_ops = {
- .ipi_inject = sbi_send_cpumask_ipi
+ .ipi_inject = sbi_send_cpumask_ipi,
+ .ipi_clear = sbi_ipi_clear
};
void __init sbi_init(void)
diff --git a/arch/riscv/kernel/smp.c b/arch/riscv/kernel/smp.c
index 760a64518c58..c56d67f53ea9 100644
--- a/arch/riscv/kernel/smp.c
+++ b/arch/riscv/kernel/smp.c
@@ -83,8 +83,6 @@ void riscv_clear_ipi(void)
{
if (ipi_ops && ipi_ops->ipi_clear)
ipi_ops->ipi_clear();
-
- csr_clear(CSR_IP, IE_SIE);
}
EXPORT_SYMBOL_GPL(riscv_clear_ipi);
--
2.34.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v11 2/7] irqchip/riscv-intc: Allow drivers to directly discover INTC hwnode
2022-11-14 9:38 [PATCH v11 0/7] RISC-V IPI Improvements Anup Patel
2022-11-14 9:38 ` [PATCH v11 1/7] RISC-V: Clear SIP bit only when using SBI IPI operations Anup Patel
@ 2022-11-14 9:38 ` Anup Patel
2022-11-14 9:39 ` [PATCH v11 3/7] genirq: Add mechanism to multiplex a single HW IPI Anup Patel
` (4 subsequent siblings)
6 siblings, 0 replies; 12+ messages in thread
From: Anup Patel @ 2022-11-14 9:38 UTC (permalink / raw)
To: Palmer Dabbelt, Paul Walmsley, Thomas Gleixner, Marc Zyngier,
Daniel Lezcano
Cc: Atish Patra, Alistair Francis, Anup Patel, linux-riscv,
linux-kernel, Anup Patel, Atish Patra
Various RISC-V drivers (such as SBI IPI, SBI Timer, SBI PMU, and
KVM RISC-V) don't have associated DT node but these drivers need
standard per-CPU (local) interrupts defined by the RISC-V privileged
specification.
We add riscv_get_intc_hwnode() in arch/riscv which allows RISC-V
drivers not having DT node to discover INTC hwnode which in-turn
helps these drivers to map per-CPU (local) interrupts provided
by the INTC driver.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
---
arch/riscv/include/asm/irq.h | 4 ++++
arch/riscv/kernel/irq.c | 18 ++++++++++++++++++
drivers/irqchip/irq-riscv-intc.c | 7 +++++++
3 files changed, 29 insertions(+)
diff --git a/arch/riscv/include/asm/irq.h b/arch/riscv/include/asm/irq.h
index e4c435509983..43b9ebfbd943 100644
--- a/arch/riscv/include/asm/irq.h
+++ b/arch/riscv/include/asm/irq.h
@@ -12,6 +12,10 @@
#include <asm-generic/irq.h>
+void riscv_set_intc_hwnode_fn(struct fwnode_handle *(*fn)(void));
+
+struct fwnode_handle *riscv_get_intc_hwnode(void);
+
extern void __init init_IRQ(void);
#endif /* _ASM_RISCV_IRQ_H */
diff --git a/arch/riscv/kernel/irq.c b/arch/riscv/kernel/irq.c
index 7207fa08d78f..96d3171f0ca1 100644
--- a/arch/riscv/kernel/irq.c
+++ b/arch/riscv/kernel/irq.c
@@ -7,9 +7,27 @@
#include <linux/interrupt.h>
#include <linux/irqchip.h>
+#include <linux/irqdomain.h>
+#include <linux/module.h>
#include <linux/seq_file.h>
#include <asm/smp.h>
+static struct fwnode_handle *(*__get_intc_node)(void);
+
+void riscv_set_intc_hwnode_fn(struct fwnode_handle *(*fn)(void))
+{
+ __get_intc_node = fn;
+}
+
+struct fwnode_handle *riscv_get_intc_hwnode(void)
+{
+ if (__get_intc_node)
+ return __get_intc_node();
+
+ return NULL;
+}
+EXPORT_SYMBOL_GPL(riscv_get_intc_hwnode);
+
int arch_show_interrupts(struct seq_file *p, int prec)
{
show_ipi_stats(p, prec);
diff --git a/drivers/irqchip/irq-riscv-intc.c b/drivers/irqchip/irq-riscv-intc.c
index 499e5f81b3fe..9066467e99e4 100644
--- a/drivers/irqchip/irq-riscv-intc.c
+++ b/drivers/irqchip/irq-riscv-intc.c
@@ -92,6 +92,11 @@ static const struct irq_domain_ops riscv_intc_domain_ops = {
.xlate = irq_domain_xlate_onecell,
};
+static struct fwnode_handle *riscv_intc_hwnode(void)
+{
+ return intc_domain->fwnode;
+}
+
static int __init riscv_intc_init(struct device_node *node,
struct device_node *parent)
{
@@ -126,6 +131,8 @@ static int __init riscv_intc_init(struct device_node *node,
return rc;
}
+ riscv_set_intc_hwnode_fn(riscv_intc_hwnode);
+
cpuhp_setup_state(CPUHP_AP_IRQ_RISCV_STARTING,
"irqchip/riscv/intc:starting",
riscv_intc_cpu_starting,
--
2.34.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v11 3/7] genirq: Add mechanism to multiplex a single HW IPI
2022-11-14 9:38 [PATCH v11 0/7] RISC-V IPI Improvements Anup Patel
2022-11-14 9:38 ` [PATCH v11 1/7] RISC-V: Clear SIP bit only when using SBI IPI operations Anup Patel
2022-11-14 9:38 ` [PATCH v11 2/7] irqchip/riscv-intc: Allow drivers to directly discover INTC hwnode Anup Patel
@ 2022-11-14 9:39 ` Anup Patel
2022-11-26 12:42 ` Marc Zyngier
2022-11-14 9:39 ` [PATCH v11 4/7] RISC-V: Treat IPIs as normal Linux IRQs Anup Patel
` (3 subsequent siblings)
6 siblings, 1 reply; 12+ messages in thread
From: Anup Patel @ 2022-11-14 9:39 UTC (permalink / raw)
To: Palmer Dabbelt, Paul Walmsley, Thomas Gleixner, Marc Zyngier,
Daniel Lezcano
Cc: Atish Patra, Alistair Francis, Anup Patel, linux-riscv,
linux-kernel, Anup Patel
All RISC-V platforms have a single HW IPI provided by the INTC local
interrupt controller. The HW method to trigger INTC IPI can be through
external irqchip (e.g. RISC-V AIA), through platform specific device
(e.g. SiFive CLINT timer), or through firmware (e.g. SBI IPI call).
To support multiple IPIs on RISC-V, we add a generic IPI multiplexing
mechanism which help us create multiple virtual IPIs using a single
HW IPI. This generic IPI multiplexing is inspired from the Apple AIC
irqchip driver and it is shared by various RISC-V irqchip drivers.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
---
include/linux/irq.h | 18 +++
kernel/irq/Kconfig | 5 +
kernel/irq/Makefile | 1 +
kernel/irq/ipi-mux.c | 268 +++++++++++++++++++++++++++++++++++++++++++
4 files changed, 292 insertions(+)
create mode 100644 kernel/irq/ipi-mux.c
diff --git a/include/linux/irq.h b/include/linux/irq.h
index c3eb89606c2b..5ab702cb0a5b 100644
--- a/include/linux/irq.h
+++ b/include/linux/irq.h
@@ -1266,6 +1266,24 @@ int __ipi_send_mask(struct irq_desc *desc, const struct cpumask *dest);
int ipi_send_single(unsigned int virq, unsigned int cpu);
int ipi_send_mask(unsigned int virq, const struct cpumask *dest);
+/**
+ * struct ipi_mux_ops - IPI multiplex operations
+ *
+ * @ipi_mux_pre_handle: Optional function called before handling parent IPI
+ * @ipi_mux_post_handle:Optional function called after handling parent IPI
+ * @ipi_mux_send: Trigger parent IPI on target CPUs
+ */
+struct ipi_mux_ops {
+ void (*ipi_mux_pre_handle)(unsigned int parent_virq, void *data);
+ void (*ipi_mux_post_handle)(unsigned int parent_virq, void *data);
+ void (*ipi_mux_send)(unsigned int parent_virq, void *data,
+ const struct cpumask *mask);
+};
+
+void ipi_mux_process(void);
+int ipi_mux_create(unsigned int parent_virq, unsigned int nr_ipi,
+ const struct ipi_mux_ops *ops, void *data);
+
#ifdef CONFIG_GENERIC_IRQ_MULTI_HANDLER
/*
* Registers a generic IRQ handling function as the top-level IRQ handler in
diff --git a/kernel/irq/Kconfig b/kernel/irq/Kconfig
index db3d174c53d4..df17dbc54b02 100644
--- a/kernel/irq/Kconfig
+++ b/kernel/irq/Kconfig
@@ -86,6 +86,11 @@ config GENERIC_IRQ_IPI
depends on SMP
select IRQ_DOMAIN_HIERARCHY
+# Generic IRQ IPI Mux support
+config GENERIC_IRQ_IPI_MUX
+ bool
+ depends on SMP
+
# Generic MSI interrupt support
config GENERIC_MSI_IRQ
bool
diff --git a/kernel/irq/Makefile b/kernel/irq/Makefile
index b4f53717d143..f19d3080bf11 100644
--- a/kernel/irq/Makefile
+++ b/kernel/irq/Makefile
@@ -15,6 +15,7 @@ obj-$(CONFIG_GENERIC_IRQ_MIGRATION) += cpuhotplug.o
obj-$(CONFIG_PM_SLEEP) += pm.o
obj-$(CONFIG_GENERIC_MSI_IRQ) += msi.o
obj-$(CONFIG_GENERIC_IRQ_IPI) += ipi.o
+obj-$(CONFIG_GENERIC_IRQ_IPI_MUX) += ipi-mux.o
obj-$(CONFIG_SMP) += affinity.o
obj-$(CONFIG_GENERIC_IRQ_DEBUGFS) += debugfs.o
obj-$(CONFIG_GENERIC_IRQ_MATRIX_ALLOCATOR) += matrix.o
diff --git a/kernel/irq/ipi-mux.c b/kernel/irq/ipi-mux.c
new file mode 100644
index 000000000000..259e00366dd7
--- /dev/null
+++ b/kernel/irq/ipi-mux.c
@@ -0,0 +1,268 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Multiplex several virtual IPIs over a single HW IPI.
+ *
+ * Copyright The Asahi Linux Contributors
+ * Copyright (c) 2022 Ventana Micro Systems Inc.
+ */
+
+#define pr_fmt(fmt) "ipi-mux: " fmt
+#include <linux/cpu.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/irqchip.h>
+#include <linux/irqchip/chained_irq.h>
+#include <linux/irqdomain.h>
+#include <linux/jump_label.h>
+#include <linux/percpu.h>
+#include <linux/smp.h>
+
+struct ipi_mux_cpu {
+ atomic_t enable;
+ atomic_t bits;
+ struct cpumask send_mask;
+};
+
+struct ipi_mux_control {
+ void *data;
+ unsigned int nr;
+ unsigned int parent_virq;
+ struct irq_domain *domain;
+ const struct ipi_mux_ops *ops;
+ struct ipi_mux_cpu __percpu *cpu;
+};
+
+static struct ipi_mux_control *imux;
+static DEFINE_STATIC_KEY_FALSE(imux_pre_handle);
+static DEFINE_STATIC_KEY_FALSE(imux_post_handle);
+
+static void ipi_mux_mask(struct irq_data *d)
+{
+ struct ipi_mux_cpu *icpu = this_cpu_ptr(imux->cpu);
+
+ atomic_andnot(BIT(irqd_to_hwirq(d)), &icpu->enable);
+}
+
+static void ipi_mux_unmask(struct irq_data *d)
+{
+ u32 ibit = BIT(irqd_to_hwirq(d));
+ struct ipi_mux_cpu *icpu = this_cpu_ptr(imux->cpu);
+
+ atomic_or(ibit, &icpu->enable);
+
+ /*
+ * The atomic_or() above must complete before the atomic_read()
+ * below to avoid racing ipi_mux_send_mask().
+ */
+ smp_mb__after_atomic();
+
+ /* If a pending IPI was unmasked, raise a parent IPI immediately. */
+ if (atomic_read(&icpu->bits) & ibit)
+ imux->ops->ipi_mux_send(imux->parent_virq, imux->data,
+ cpumask_of(smp_processor_id()));
+}
+
+static void ipi_mux_send_mask(struct irq_data *d, const struct cpumask *mask)
+{
+ u32 ibit = BIT(irqd_to_hwirq(d));
+ struct ipi_mux_cpu *icpu = this_cpu_ptr(imux->cpu);
+ struct cpumask *send_mask = &icpu->send_mask;
+ unsigned long flags;
+ int cpu;
+
+ /*
+ * We use send_mask as a per-CPU variable so disable local
+ * interrupts to avoid being preempted.
+ */
+ local_irq_save(flags);
+
+ cpumask_clear(send_mask);
+
+ for_each_cpu(cpu, mask) {
+ icpu = per_cpu_ptr(imux->cpu, cpu);
+ atomic_or(ibit, &icpu->bits);
+
+ /*
+ * The atomic_or() above must complete before
+ * the atomic_read() below to avoid racing with
+ * ipi_mux_unmask().
+ */
+ smp_mb__after_atomic();
+
+ if (atomic_read(&icpu->enable) & ibit)
+ cpumask_set_cpu(cpu, send_mask);
+ }
+
+ /* Trigger the parent IPI */
+ imux->ops->ipi_mux_send(imux->parent_virq, imux->data, send_mask);
+
+ local_irq_restore(flags);
+}
+
+static const struct irq_chip ipi_mux_chip = {
+ .name = "IPI Mux",
+ .irq_mask = ipi_mux_mask,
+ .irq_unmask = ipi_mux_unmask,
+ .ipi_send_mask = ipi_mux_send_mask,
+};
+
+static int ipi_mux_domain_alloc(struct irq_domain *d, unsigned int virq,
+ unsigned int nr_irqs, void *arg)
+{
+ int i;
+
+ for (i = 0; i < nr_irqs; i++) {
+ irq_set_percpu_devid(virq + i);
+ irq_domain_set_info(d, virq + i, i,
+ &ipi_mux_chip, d->host_data,
+ handle_percpu_devid_irq, NULL, NULL);
+ }
+
+ return 0;
+}
+
+static const struct irq_domain_ops ipi_mux_domain_ops = {
+ .alloc = ipi_mux_domain_alloc,
+ .free = irq_domain_free_irqs_top,
+};
+
+/**
+ * ipi_mux_process - Process multiplexed virtual IPIs
+ */
+void ipi_mux_process(void)
+{
+ struct ipi_mux_cpu *icpu = this_cpu_ptr(imux->cpu);
+ irq_hw_number_t hwirq;
+ unsigned long ipis;
+ int en;
+
+ if (static_branch_unlikely(&imux_pre_handle))
+ imux->ops->ipi_mux_pre_handle(imux->parent_virq, imux->data);
+
+ /*
+ * Reading enable mask does not need to be ordered as long as
+ * this function called from interrupt handler because only
+ * the CPU itself can change it's own enable mask.
+ */
+ en = atomic_read(&icpu->enable);
+
+ /*
+ * Clear the IPIs we are about to handle. This pairs with the
+ * atomic_fetch_or_release() in ipi_mux_send_mask().
+ */
+ ipis = atomic_fetch_andnot(en, &icpu->bits) & en;
+
+ for_each_set_bit(hwirq, &ipis, imux->nr)
+ generic_handle_domain_irq(imux->domain, hwirq);
+
+ if (static_branch_unlikely(&imux_post_handle))
+ imux->ops->ipi_mux_post_handle(imux->parent_virq, imux->data);
+}
+
+static void ipi_mux_handler(struct irq_desc *desc)
+{
+ struct irq_chip *chip = irq_desc_get_chip(desc);
+
+ chained_irq_enter(chip, desc);
+ ipi_mux_process();
+ chained_irq_exit(chip, desc);
+}
+
+/**
+ * ipi_mux_create - Create virtual IPIs multiplexed on top of a single
+ * parent IPI.
+ * @parent_virq: virq of the parent per-CPU IRQ
+ * @nr_ipi: number of virtual IPIs to create. This should
+ * be <= BITS_PER_TYPE(int)
+ * @ops: multiplexing operations for the parent IPI
+ * @data: opaque data used by the multiplexing operations
+ *
+ * If the parent IPI > 0 then ipi_mux_process() will be automatically
+ * called via chained handler.
+ *
+ * If the parent IPI <= 0 then it is responsibility of irqchip drivers
+ * to explicitly call ipi_mux_process() for processing muxed IPIs.
+ *
+ * Returns first virq of the newly created virtual IPIs upon success
+ * or <=0 upon failure
+ */
+int ipi_mux_create(unsigned int parent_virq, unsigned int nr_ipi,
+ const struct ipi_mux_ops *ops, void *data)
+{
+ struct fwnode_handle *fwnode;
+ struct irq_domain *domain;
+ int rc;
+
+ if (imux)
+ return -EEXIST;
+
+ if (BITS_PER_TYPE(int) < nr_ipi || !ops || !ops->ipi_mux_send)
+ return -EINVAL;
+
+ if (parent_virq &&
+ !irqd_is_per_cpu(irq_desc_get_irq_data(irq_to_desc(parent_virq))))
+ return -EINVAL;
+
+ imux = kzalloc(sizeof(*imux), GFP_KERNEL);
+ if (!imux)
+ return -ENOMEM;
+
+ imux->cpu = alloc_percpu(typeof(*imux->cpu));
+ if (!imux->cpu) {
+ rc = -ENOMEM;
+ goto fail_free_mux;
+ }
+
+ fwnode = irq_domain_alloc_named_fwnode("IPI-Mux");
+ if (!fwnode) {
+ pr_err("unable to create IPI Mux fwnode\n");
+ rc = -ENOMEM;
+ goto fail_free_cpu;
+ }
+
+ domain = irq_domain_create_simple(fwnode, nr_ipi, 0,
+ &ipi_mux_domain_ops, NULL);
+ if (!domain) {
+ pr_err("unable to add IPI Mux domain\n");
+ rc = -ENOMEM;
+ goto fail_free_fwnode;
+ }
+
+ domain->flags |= IRQ_DOMAIN_FLAG_IPI_SINGLE;
+ irq_domain_update_bus_token(domain, DOMAIN_BUS_IPI);
+
+ rc = __irq_domain_alloc_irqs(domain, -1, nr_ipi,
+ NUMA_NO_NODE, NULL, false, NULL);
+ if (rc <= 0) {
+ pr_err("unable to alloc IRQs from IPI Mux domain\n");
+ goto fail_free_domain;
+ }
+
+ imux->domain = domain;
+ imux->data = data;
+ imux->nr = nr_ipi;
+ imux->parent_virq = parent_virq;
+ imux->ops = ops;
+
+ if (imux->ops->ipi_mux_pre_handle)
+ static_branch_enable(&imux_pre_handle);
+
+ if (imux->ops->ipi_mux_post_handle)
+ static_branch_enable(&imux_post_handle);
+
+ if (parent_virq > 0)
+ irq_set_chained_handler(parent_virq, ipi_mux_handler);
+
+ return rc;
+
+fail_free_domain:
+ irq_domain_remove(domain);
+fail_free_fwnode:
+ irq_domain_free_fwnode(fwnode);
+fail_free_cpu:
+ free_percpu(imux->cpu);
+fail_free_mux:
+ kfree(imux);
+ imux = NULL;
+ return rc;
+}
--
2.34.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 12+ messages in thread* Re: [PATCH v11 3/7] genirq: Add mechanism to multiplex a single HW IPI
2022-11-14 9:39 ` [PATCH v11 3/7] genirq: Add mechanism to multiplex a single HW IPI Anup Patel
@ 2022-11-26 12:42 ` Marc Zyngier
2022-11-26 13:31 ` Anup Patel
0 siblings, 1 reply; 12+ messages in thread
From: Marc Zyngier @ 2022-11-26 12:42 UTC (permalink / raw)
To: Anup Patel
Cc: Palmer Dabbelt, Paul Walmsley, Thomas Gleixner, Daniel Lezcano,
Atish Patra, Alistair Francis, Anup Patel, linux-riscv,
linux-kernel
On Mon, 14 Nov 2022 09:39:00 +0000,
Anup Patel <apatel@ventanamicro.com> wrote:
>
> All RISC-V platforms have a single HW IPI provided by the INTC local
> interrupt controller. The HW method to trigger INTC IPI can be through
> external irqchip (e.g. RISC-V AIA), through platform specific device
> (e.g. SiFive CLINT timer), or through firmware (e.g. SBI IPI call).
>
> To support multiple IPIs on RISC-V, we add a generic IPI multiplexing
> mechanism which help us create multiple virtual IPIs using a single
> HW IPI. This generic IPI multiplexing is inspired from the Apple AIC
> irqchip driver and it is shared by various RISC-V irqchip drivers.
>
> Signed-off-by: Anup Patel <apatel@ventanamicro.com>
> ---
> include/linux/irq.h | 18 +++
> kernel/irq/Kconfig | 5 +
> kernel/irq/Makefile | 1 +
> kernel/irq/ipi-mux.c | 268 +++++++++++++++++++++++++++++++++++++++++++
> 4 files changed, 292 insertions(+)
> create mode 100644 kernel/irq/ipi-mux.c
>
> diff --git a/include/linux/irq.h b/include/linux/irq.h
> index c3eb89606c2b..5ab702cb0a5b 100644
> --- a/include/linux/irq.h
> +++ b/include/linux/irq.h
> @@ -1266,6 +1266,24 @@ int __ipi_send_mask(struct irq_desc *desc, const struct cpumask *dest);
> int ipi_send_single(unsigned int virq, unsigned int cpu);
> int ipi_send_mask(unsigned int virq, const struct cpumask *dest);
>
> +/**
> + * struct ipi_mux_ops - IPI multiplex operations
> + *
> + * @ipi_mux_pre_handle: Optional function called before handling parent IPI
> + * @ipi_mux_post_handle:Optional function called after handling parent IPI
> + * @ipi_mux_send: Trigger parent IPI on target CPUs
> + */
> +struct ipi_mux_ops {
> + void (*ipi_mux_pre_handle)(unsigned int parent_virq, void *data);
> + void (*ipi_mux_post_handle)(unsigned int parent_virq, void *data);
I still haven't seen any decent explanation for this other than "we
need it". What is it that cannot be achieved via the irq_ack() and
irq_eoi() callbacks?
> + void (*ipi_mux_send)(unsigned int parent_virq, void *data,
> + const struct cpumask *mask);
In what context would the 'parent_virq' be useful? You are *sending*
an IPI, not receiving it, and I expect the mechanism by which you send
such an IPI to be independent of the Linux view of the irq.
Also, please swap data and mask in the function signature.
> +};
> +
> +void ipi_mux_process(void);
> +int ipi_mux_create(unsigned int parent_virq, unsigned int nr_ipi,
> + const struct ipi_mux_ops *ops, void *data);
> +
> #ifdef CONFIG_GENERIC_IRQ_MULTI_HANDLER
> /*
> * Registers a generic IRQ handling function as the top-level IRQ handler in
> diff --git a/kernel/irq/Kconfig b/kernel/irq/Kconfig
> index db3d174c53d4..df17dbc54b02 100644
> --- a/kernel/irq/Kconfig
> +++ b/kernel/irq/Kconfig
> @@ -86,6 +86,11 @@ config GENERIC_IRQ_IPI
> depends on SMP
> select IRQ_DOMAIN_HIERARCHY
>
> +# Generic IRQ IPI Mux support
> +config GENERIC_IRQ_IPI_MUX
> + bool
> + depends on SMP
> +
> # Generic MSI interrupt support
> config GENERIC_MSI_IRQ
> bool
> diff --git a/kernel/irq/Makefile b/kernel/irq/Makefile
> index b4f53717d143..f19d3080bf11 100644
> --- a/kernel/irq/Makefile
> +++ b/kernel/irq/Makefile
> @@ -15,6 +15,7 @@ obj-$(CONFIG_GENERIC_IRQ_MIGRATION) += cpuhotplug.o
> obj-$(CONFIG_PM_SLEEP) += pm.o
> obj-$(CONFIG_GENERIC_MSI_IRQ) += msi.o
> obj-$(CONFIG_GENERIC_IRQ_IPI) += ipi.o
> +obj-$(CONFIG_GENERIC_IRQ_IPI_MUX) += ipi-mux.o
> obj-$(CONFIG_SMP) += affinity.o
> obj-$(CONFIG_GENERIC_IRQ_DEBUGFS) += debugfs.o
> obj-$(CONFIG_GENERIC_IRQ_MATRIX_ALLOCATOR) += matrix.o
> diff --git a/kernel/irq/ipi-mux.c b/kernel/irq/ipi-mux.c
> new file mode 100644
> index 000000000000..259e00366dd7
> --- /dev/null
> +++ b/kernel/irq/ipi-mux.c
> @@ -0,0 +1,268 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * Multiplex several virtual IPIs over a single HW IPI.
> + *
> + * Copyright The Asahi Linux Contributors
> + * Copyright (c) 2022 Ventana Micro Systems Inc.
> + */
> +
> +#define pr_fmt(fmt) "ipi-mux: " fmt
> +#include <linux/cpu.h>
> +#include <linux/init.h>
> +#include <linux/irq.h>
> +#include <linux/irqchip.h>
> +#include <linux/irqchip/chained_irq.h>
> +#include <linux/irqdomain.h>
> +#include <linux/jump_label.h>
> +#include <linux/percpu.h>
> +#include <linux/smp.h>
> +
> +struct ipi_mux_cpu {
> + atomic_t enable;
> + atomic_t bits;
> + struct cpumask send_mask;
> +};
> +
> +struct ipi_mux_control {
> + void *data;
> + unsigned int nr;
Honestly, I think we can get rid of this. The number of IPIs Linux
uses is pretty small, and assuming a huge value (like 32) would be
enough. It would save looking up this value on each IPI handling.
> + unsigned int parent_virq;
> + struct irq_domain *domain;
> + const struct ipi_mux_ops *ops;
> + struct ipi_mux_cpu __percpu *cpu;
> +};
> +
> +static struct ipi_mux_control *imux;
> +static DEFINE_STATIC_KEY_FALSE(imux_pre_handle);
> +static DEFINE_STATIC_KEY_FALSE(imux_post_handle);
> +
> +static void ipi_mux_mask(struct irq_data *d)
> +{
> + struct ipi_mux_cpu *icpu = this_cpu_ptr(imux->cpu);
> +
> + atomic_andnot(BIT(irqd_to_hwirq(d)), &icpu->enable);
> +}
> +
> +static void ipi_mux_unmask(struct irq_data *d)
> +{
> + u32 ibit = BIT(irqd_to_hwirq(d));
> + struct ipi_mux_cpu *icpu = this_cpu_ptr(imux->cpu);
> +
> + atomic_or(ibit, &icpu->enable);
> +
> + /*
> + * The atomic_or() above must complete before the atomic_read()
> + * below to avoid racing ipi_mux_send_mask().
> + */
> + smp_mb__after_atomic();
> +
> + /* If a pending IPI was unmasked, raise a parent IPI immediately. */
> + if (atomic_read(&icpu->bits) & ibit)
> + imux->ops->ipi_mux_send(imux->parent_virq, imux->data,
> + cpumask_of(smp_processor_id()));
> +}
> +
> +static void ipi_mux_send_mask(struct irq_data *d, const struct cpumask *mask)
> +{
> + u32 ibit = BIT(irqd_to_hwirq(d));
> + struct ipi_mux_cpu *icpu = this_cpu_ptr(imux->cpu);
> + struct cpumask *send_mask = &icpu->send_mask;
> + unsigned long flags;
> + int cpu;
> +
> + /*
> + * We use send_mask as a per-CPU variable so disable local
> + * interrupts to avoid being preempted.
> + */
> + local_irq_save(flags);
> +
> + cpumask_clear(send_mask);
> +
> + for_each_cpu(cpu, mask) {
> + icpu = per_cpu_ptr(imux->cpu, cpu);
> + atomic_or(ibit, &icpu->bits);
> +
> + /*
> + * The atomic_or() above must complete before
> + * the atomic_read() below to avoid racing with
> + * ipi_mux_unmask().
> + */
> + smp_mb__after_atomic();
> +
> + if (atomic_read(&icpu->enable) & ibit)
> + cpumask_set_cpu(cpu, send_mask);
> + }
> +
> + /* Trigger the parent IPI */
> + imux->ops->ipi_mux_send(imux->parent_virq, imux->data, send_mask);
> +
> + local_irq_restore(flags);
> +}
> +
> +static const struct irq_chip ipi_mux_chip = {
> + .name = "IPI Mux",
> + .irq_mask = ipi_mux_mask,
> + .irq_unmask = ipi_mux_unmask,
> + .ipi_send_mask = ipi_mux_send_mask,
> +};
I really think this could either be supplied by the irqchip, or
somehow patched to avoid the pointless imux->ops->ipi_mux_send
indirection. Pointer chasing hurts.
> +
> +static int ipi_mux_domain_alloc(struct irq_domain *d, unsigned int virq,
> + unsigned int nr_irqs, void *arg)
> +{
> + int i;
> +
> + for (i = 0; i < nr_irqs; i++) {
> + irq_set_percpu_devid(virq + i);
> + irq_domain_set_info(d, virq + i, i,
> + &ipi_mux_chip, d->host_data,
> + handle_percpu_devid_irq, NULL, NULL);
> + }
> +
> + return 0;
> +}
> +
> +static const struct irq_domain_ops ipi_mux_domain_ops = {
> + .alloc = ipi_mux_domain_alloc,
> + .free = irq_domain_free_irqs_top,
> +};
> +
> +/**
> + * ipi_mux_process - Process multiplexed virtual IPIs
> + */
> +void ipi_mux_process(void)
> +{
> + struct ipi_mux_cpu *icpu = this_cpu_ptr(imux->cpu);
> + irq_hw_number_t hwirq;
> + unsigned long ipis;
> + int en;
Please use an unsigned type here (see the rationale in atomic_t.txt).
> +
> + if (static_branch_unlikely(&imux_pre_handle))
> + imux->ops->ipi_mux_pre_handle(imux->parent_virq, imux->data);
> +
> + /*
> + * Reading enable mask does not need to be ordered as long as
> + * this function called from interrupt handler because only
> + * the CPU itself can change it's own enable mask.
> + */
> + en = atomic_read(&icpu->enable);
> +
> + /*
> + * Clear the IPIs we are about to handle. This pairs with the
> + * atomic_fetch_or_release() in ipi_mux_send_mask().
> + */
> + ipis = atomic_fetch_andnot(en, &icpu->bits) & en;
> +
> + for_each_set_bit(hwirq, &ipis, imux->nr)
> + generic_handle_domain_irq(imux->domain, hwirq);
> +
> + if (static_branch_unlikely(&imux_post_handle))
> + imux->ops->ipi_mux_post_handle(imux->parent_virq, imux->data);
Do you see what I meant about the {pre,post}_handle callback, and how
they are *exactly* like irq_{ack,eoi}?
> +}
> +
> +static void ipi_mux_handler(struct irq_desc *desc)
> +{
> + struct irq_chip *chip = irq_desc_get_chip(desc);
> +
> + chained_irq_enter(chip, desc);
> + ipi_mux_process();
> + chained_irq_exit(chip, desc);
> +}
> +
> +/**
> + * ipi_mux_create - Create virtual IPIs multiplexed on top of a single
> + * parent IPI.
> + * @parent_virq: virq of the parent per-CPU IRQ
> + * @nr_ipi: number of virtual IPIs to create. This should
> + * be <= BITS_PER_TYPE(int)
> + * @ops: multiplexing operations for the parent IPI
> + * @data: opaque data used by the multiplexing operations
What is the use for data? If anything, that data should be passed via
the mux interrupt. But the whole point of this is to make the mux
invisible. So this whole 'data' business is a mystery to me.
> + *
> + * If the parent IPI > 0 then ipi_mux_process() will be automatically
> + * called via chained handler.
> + *
> + * If the parent IPI <= 0 then it is responsibility of irqchip drivers
> + * to explicitly call ipi_mux_process() for processing muxed IPIs.
0 is a much more idiomatic value for "no parent IRQ". < 0 normally
represents an error.
> + *
> + * Returns first virq of the newly created virtual IPIs upon success
> + * or <=0 upon failure
> + */
> +int ipi_mux_create(unsigned int parent_virq, unsigned int nr_ipi,
Tell me how I can express a negative parent_virq here?
> + const struct ipi_mux_ops *ops, void *data)
> +{
> + struct fwnode_handle *fwnode;
> + struct irq_domain *domain;
> + int rc;
> +
> + if (imux)
> + return -EEXIST;
> +
> + if (BITS_PER_TYPE(int) < nr_ipi || !ops || !ops->ipi_mux_send)
> + return -EINVAL;
> +
> + if (parent_virq &&
> + !irqd_is_per_cpu(irq_desc_get_irq_data(irq_to_desc(parent_virq))))
> + return -EINVAL;
See how buggy this is if I follow your definition of "no parent IRQ"?
M.
--
Without deviation from the norm, progress is not possible.
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply [flat|nested] 12+ messages in thread* Re: [PATCH v11 3/7] genirq: Add mechanism to multiplex a single HW IPI
2022-11-26 12:42 ` Marc Zyngier
@ 2022-11-26 13:31 ` Anup Patel
2022-11-26 14:28 ` Marc Zyngier
0 siblings, 1 reply; 12+ messages in thread
From: Anup Patel @ 2022-11-26 13:31 UTC (permalink / raw)
To: Marc Zyngier
Cc: Palmer Dabbelt, Paul Walmsley, Thomas Gleixner, Daniel Lezcano,
Atish Patra, Alistair Francis, Anup Patel, linux-riscv,
linux-kernel
On Sat, Nov 26, 2022 at 6:12 PM Marc Zyngier <maz@kernel.org> wrote:
>
> On Mon, 14 Nov 2022 09:39:00 +0000,
> Anup Patel <apatel@ventanamicro.com> wrote:
> >
> > All RISC-V platforms have a single HW IPI provided by the INTC local
> > interrupt controller. The HW method to trigger INTC IPI can be through
> > external irqchip (e.g. RISC-V AIA), through platform specific device
> > (e.g. SiFive CLINT timer), or through firmware (e.g. SBI IPI call).
> >
> > To support multiple IPIs on RISC-V, we add a generic IPI multiplexing
> > mechanism which help us create multiple virtual IPIs using a single
> > HW IPI. This generic IPI multiplexing is inspired from the Apple AIC
> > irqchip driver and it is shared by various RISC-V irqchip drivers.
> >
> > Signed-off-by: Anup Patel <apatel@ventanamicro.com>
> > ---
> > include/linux/irq.h | 18 +++
> > kernel/irq/Kconfig | 5 +
> > kernel/irq/Makefile | 1 +
> > kernel/irq/ipi-mux.c | 268 +++++++++++++++++++++++++++++++++++++++++++
> > 4 files changed, 292 insertions(+)
> > create mode 100644 kernel/irq/ipi-mux.c
> >
> > diff --git a/include/linux/irq.h b/include/linux/irq.h
> > index c3eb89606c2b..5ab702cb0a5b 100644
> > --- a/include/linux/irq.h
> > +++ b/include/linux/irq.h
> > @@ -1266,6 +1266,24 @@ int __ipi_send_mask(struct irq_desc *desc, const struct cpumask *dest);
> > int ipi_send_single(unsigned int virq, unsigned int cpu);
> > int ipi_send_mask(unsigned int virq, const struct cpumask *dest);
> >
> > +/**
> > + * struct ipi_mux_ops - IPI multiplex operations
> > + *
> > + * @ipi_mux_pre_handle: Optional function called before handling parent IPI
> > + * @ipi_mux_post_handle:Optional function called after handling parent IPI
> > + * @ipi_mux_send: Trigger parent IPI on target CPUs
> > + */
> > +struct ipi_mux_ops {
> > + void (*ipi_mux_pre_handle)(unsigned int parent_virq, void *data);
> > + void (*ipi_mux_post_handle)(unsigned int parent_virq, void *data);
>
> I still haven't seen any decent explanation for this other than "we
> need it". What is it that cannot be achieved via the irq_ack() and
> irq_eoi() callbacks?
Sure, even I think these are strange looking callbacks. I will drop
these callbacks in the next patch revision.
>
> > + void (*ipi_mux_send)(unsigned int parent_virq, void *data,
> > + const struct cpumask *mask);
>
> In what context would the 'parent_virq' be useful? You are *sending*
> an IPI, not receiving it, and I expect the mechanism by which you send
> such an IPI to be independent of the Linux view of the irq.
Okay, I will drop the 'parent_virq' parameter.
>
> Also, please swap data and mask in the function signature.
Okay, I will change the order.
>
> > +};
> > +
> > +void ipi_mux_process(void);
> > +int ipi_mux_create(unsigned int parent_virq, unsigned int nr_ipi,
> > + const struct ipi_mux_ops *ops, void *data);
> > +
> > #ifdef CONFIG_GENERIC_IRQ_MULTI_HANDLER
> > /*
> > * Registers a generic IRQ handling function as the top-level IRQ handler in
> > diff --git a/kernel/irq/Kconfig b/kernel/irq/Kconfig
> > index db3d174c53d4..df17dbc54b02 100644
> > --- a/kernel/irq/Kconfig
> > +++ b/kernel/irq/Kconfig
> > @@ -86,6 +86,11 @@ config GENERIC_IRQ_IPI
> > depends on SMP
> > select IRQ_DOMAIN_HIERARCHY
> >
> > +# Generic IRQ IPI Mux support
> > +config GENERIC_IRQ_IPI_MUX
> > + bool
> > + depends on SMP
> > +
> > # Generic MSI interrupt support
> > config GENERIC_MSI_IRQ
> > bool
> > diff --git a/kernel/irq/Makefile b/kernel/irq/Makefile
> > index b4f53717d143..f19d3080bf11 100644
> > --- a/kernel/irq/Makefile
> > +++ b/kernel/irq/Makefile
> > @@ -15,6 +15,7 @@ obj-$(CONFIG_GENERIC_IRQ_MIGRATION) += cpuhotplug.o
> > obj-$(CONFIG_PM_SLEEP) += pm.o
> > obj-$(CONFIG_GENERIC_MSI_IRQ) += msi.o
> > obj-$(CONFIG_GENERIC_IRQ_IPI) += ipi.o
> > +obj-$(CONFIG_GENERIC_IRQ_IPI_MUX) += ipi-mux.o
> > obj-$(CONFIG_SMP) += affinity.o
> > obj-$(CONFIG_GENERIC_IRQ_DEBUGFS) += debugfs.o
> > obj-$(CONFIG_GENERIC_IRQ_MATRIX_ALLOCATOR) += matrix.o
> > diff --git a/kernel/irq/ipi-mux.c b/kernel/irq/ipi-mux.c
> > new file mode 100644
> > index 000000000000..259e00366dd7
> > --- /dev/null
> > +++ b/kernel/irq/ipi-mux.c
> > @@ -0,0 +1,268 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later
> > +/*
> > + * Multiplex several virtual IPIs over a single HW IPI.
> > + *
> > + * Copyright The Asahi Linux Contributors
> > + * Copyright (c) 2022 Ventana Micro Systems Inc.
> > + */
> > +
> > +#define pr_fmt(fmt) "ipi-mux: " fmt
> > +#include <linux/cpu.h>
> > +#include <linux/init.h>
> > +#include <linux/irq.h>
> > +#include <linux/irqchip.h>
> > +#include <linux/irqchip/chained_irq.h>
> > +#include <linux/irqdomain.h>
> > +#include <linux/jump_label.h>
> > +#include <linux/percpu.h>
> > +#include <linux/smp.h>
> > +
> > +struct ipi_mux_cpu {
> > + atomic_t enable;
> > + atomic_t bits;
> > + struct cpumask send_mask;
> > +};
> > +
> > +struct ipi_mux_control {
> > + void *data;
> > + unsigned int nr;
>
> Honestly, I think we can get rid of this. The number of IPIs Linux
> uses is pretty small, and assuming a huge value (like 32) would be
> enough. It would save looking up this value on each IPI handling.
I had kept in-case some driver wanted to create fewer (< 32)
muxed IPIs.
>
> > + unsigned int parent_virq;
> > + struct irq_domain *domain;
> > + const struct ipi_mux_ops *ops;
> > + struct ipi_mux_cpu __percpu *cpu;
> > +};
> > +
> > +static struct ipi_mux_control *imux;
> > +static DEFINE_STATIC_KEY_FALSE(imux_pre_handle);
> > +static DEFINE_STATIC_KEY_FALSE(imux_post_handle);
> > +
> > +static void ipi_mux_mask(struct irq_data *d)
> > +{
> > + struct ipi_mux_cpu *icpu = this_cpu_ptr(imux->cpu);
> > +
> > + atomic_andnot(BIT(irqd_to_hwirq(d)), &icpu->enable);
> > +}
> > +
> > +static void ipi_mux_unmask(struct irq_data *d)
> > +{
> > + u32 ibit = BIT(irqd_to_hwirq(d));
> > + struct ipi_mux_cpu *icpu = this_cpu_ptr(imux->cpu);
> > +
> > + atomic_or(ibit, &icpu->enable);
> > +
> > + /*
> > + * The atomic_or() above must complete before the atomic_read()
> > + * below to avoid racing ipi_mux_send_mask().
> > + */
> > + smp_mb__after_atomic();
> > +
> > + /* If a pending IPI was unmasked, raise a parent IPI immediately. */
> > + if (atomic_read(&icpu->bits) & ibit)
> > + imux->ops->ipi_mux_send(imux->parent_virq, imux->data,
> > + cpumask_of(smp_processor_id()));
> > +}
> > +
> > +static void ipi_mux_send_mask(struct irq_data *d, const struct cpumask *mask)
> > +{
> > + u32 ibit = BIT(irqd_to_hwirq(d));
> > + struct ipi_mux_cpu *icpu = this_cpu_ptr(imux->cpu);
> > + struct cpumask *send_mask = &icpu->send_mask;
> > + unsigned long flags;
> > + int cpu;
> > +
> > + /*
> > + * We use send_mask as a per-CPU variable so disable local
> > + * interrupts to avoid being preempted.
> > + */
> > + local_irq_save(flags);
> > +
> > + cpumask_clear(send_mask);
> > +
> > + for_each_cpu(cpu, mask) {
> > + icpu = per_cpu_ptr(imux->cpu, cpu);
> > + atomic_or(ibit, &icpu->bits);
> > +
> > + /*
> > + * The atomic_or() above must complete before
> > + * the atomic_read() below to avoid racing with
> > + * ipi_mux_unmask().
> > + */
> > + smp_mb__after_atomic();
> > +
> > + if (atomic_read(&icpu->enable) & ibit)
> > + cpumask_set_cpu(cpu, send_mask);
> > + }
> > +
> > + /* Trigger the parent IPI */
> > + imux->ops->ipi_mux_send(imux->parent_virq, imux->data, send_mask);
> > +
> > + local_irq_restore(flags);
> > +}
> > +
> > +static const struct irq_chip ipi_mux_chip = {
> > + .name = "IPI Mux",
> > + .irq_mask = ipi_mux_mask,
> > + .irq_unmask = ipi_mux_unmask,
> > + .ipi_send_mask = ipi_mux_send_mask,
> > +};
>
> I really think this could either be supplied by the irqchip, or
> somehow patched to avoid the pointless imux->ops->ipi_mux_send
> indirection. Pointer chasing hurts.
Once we remove ipi_mux_pre/post_handle() callbacks, the
"ops" will be pointless and we will be able to remove one level
of indirection here.
We certainly need a mux irqchip to implement the
mask/unmask semantics for muxed IPIs.
>
> > +
> > +static int ipi_mux_domain_alloc(struct irq_domain *d, unsigned int virq,
> > + unsigned int nr_irqs, void *arg)
> > +{
> > + int i;
> > +
> > + for (i = 0; i < nr_irqs; i++) {
> > + irq_set_percpu_devid(virq + i);
> > + irq_domain_set_info(d, virq + i, i,
> > + &ipi_mux_chip, d->host_data,
> > + handle_percpu_devid_irq, NULL, NULL);
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static const struct irq_domain_ops ipi_mux_domain_ops = {
> > + .alloc = ipi_mux_domain_alloc,
> > + .free = irq_domain_free_irqs_top,
> > +};
> > +
> > +/**
> > + * ipi_mux_process - Process multiplexed virtual IPIs
> > + */
> > +void ipi_mux_process(void)
> > +{
> > + struct ipi_mux_cpu *icpu = this_cpu_ptr(imux->cpu);
> > + irq_hw_number_t hwirq;
> > + unsigned long ipis;
> > + int en;
>
> Please use an unsigned type here (see the rationale in atomic_t.txt).
Sure, I will update.
>
> > +
> > + if (static_branch_unlikely(&imux_pre_handle))
> > + imux->ops->ipi_mux_pre_handle(imux->parent_virq, imux->data);
> > +
> > + /*
> > + * Reading enable mask does not need to be ordered as long as
> > + * this function called from interrupt handler because only
> > + * the CPU itself can change it's own enable mask.
> > + */
> > + en = atomic_read(&icpu->enable);
> > +
> > + /*
> > + * Clear the IPIs we are about to handle. This pairs with the
> > + * atomic_fetch_or_release() in ipi_mux_send_mask().
> > + */
> > + ipis = atomic_fetch_andnot(en, &icpu->bits) & en;
> > +
> > + for_each_set_bit(hwirq, &ipis, imux->nr)
> > + generic_handle_domain_irq(imux->domain, hwirq);
> > +
> > + if (static_branch_unlikely(&imux_post_handle))
> > + imux->ops->ipi_mux_post_handle(imux->parent_virq, imux->data);
>
> Do you see what I meant about the {pre,post}_handle callback, and how
> they are *exactly* like irq_{ack,eoi}?
I see. I will remove these in the next patch revision.
>
> > +}
> > +
> > +static void ipi_mux_handler(struct irq_desc *desc)
> > +{
> > + struct irq_chip *chip = irq_desc_get_chip(desc);
> > +
> > + chained_irq_enter(chip, desc);
> > + ipi_mux_process();
> > + chained_irq_exit(chip, desc);
> > +}
> > +
> > +/**
> > + * ipi_mux_create - Create virtual IPIs multiplexed on top of a single
> > + * parent IPI.
> > + * @parent_virq: virq of the parent per-CPU IRQ
> > + * @nr_ipi: number of virtual IPIs to create. This should
> > + * be <= BITS_PER_TYPE(int)
> > + * @ops: multiplexing operations for the parent IPI
> > + * @data: opaque data used by the multiplexing operations
>
> What is the use for data? If anything, that data should be passed via
> the mux interrupt. But the whole point of this is to make the mux
> invisible. So this whole 'data' business is a mystery to me.
This is added only to pass back driver data in ipi_mux_send().
>
> > + *
> > + * If the parent IPI > 0 then ipi_mux_process() will be automatically
> > + * called via chained handler.
> > + *
> > + * If the parent IPI <= 0 then it is responsibility of irqchip drivers
> > + * to explicitly call ipi_mux_process() for processing muxed IPIs.
>
> 0 is a much more idiomatic value for "no parent IRQ". < 0 normally
> represents an error.
I am going to remove the "parent_virq" parameter itself so this
will go away.
>
> > + *
> > + * Returns first virq of the newly created virtual IPIs upon success
> > + * or <=0 upon failure
> > + */
> > +int ipi_mux_create(unsigned int parent_virq, unsigned int nr_ipi,
>
> Tell me how I can express a negative parent_virq here?
Sure, I will fix this.
>
> > + const struct ipi_mux_ops *ops, void *data)
> > +{
> > + struct fwnode_handle *fwnode;
> > + struct irq_domain *domain;
> > + int rc;
> > +
> > + if (imux)
> > + return -EEXIST;
> > +
> > + if (BITS_PER_TYPE(int) < nr_ipi || !ops || !ops->ipi_mux_send)
> > + return -EINVAL;
> > +
> > + if (parent_virq &&
> > + !irqd_is_per_cpu(irq_desc_get_irq_data(irq_to_desc(parent_virq))))
> > + return -EINVAL;
>
> See how buggy this is if I follow your definition of "no parent IRQ"?
Sure, I will fix this.
>
> M.
>
> --
> Without deviation from the norm, progress is not possible.
Thanks,
Anup
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply [flat|nested] 12+ messages in thread* Re: [PATCH v11 3/7] genirq: Add mechanism to multiplex a single HW IPI
2022-11-26 13:31 ` Anup Patel
@ 2022-11-26 14:28 ` Marc Zyngier
2022-11-26 16:00 ` Anup Patel
0 siblings, 1 reply; 12+ messages in thread
From: Marc Zyngier @ 2022-11-26 14:28 UTC (permalink / raw)
To: Anup Patel
Cc: Palmer Dabbelt, Paul Walmsley, Thomas Gleixner, Daniel Lezcano,
Atish Patra, Alistair Francis, Anup Patel, linux-riscv,
linux-kernel
On Sat, 26 Nov 2022 13:31:46 +0000,
Anup Patel <apatel@ventanamicro.com> wrote:
>
> On Sat, Nov 26, 2022 at 6:12 PM Marc Zyngier <maz@kernel.org> wrote:
> >
> > On Mon, 14 Nov 2022 09:39:00 +0000,
> > Anup Patel <apatel@ventanamicro.com> wrote:
> > >
> > > +struct ipi_mux_control {
> > > + void *data;
> > > + unsigned int nr;
> >
> > Honestly, I think we can get rid of this. The number of IPIs Linux
> > uses is pretty small, and assuming a huge value (like 32) would be
> > enough. It would save looking up this value on each IPI handling.
>
> I had kept in-case some driver wanted to create fewer (< 32)
> muxed IPIs.
I'm fine with being able to specifying the max, but I'm not sure there
is a need to keep track of it any further. Certainly, the overhead of
loading this value on each IPI could be removed. On most architecture,
for_each_set_bit() and co and better optimised with a fixed number of
bits.
> > > +static const struct irq_chip ipi_mux_chip = {
> > > + .name = "IPI Mux",
> > > + .irq_mask = ipi_mux_mask,
> > > + .irq_unmask = ipi_mux_unmask,
> > > + .ipi_send_mask = ipi_mux_send_mask,
> > > +};
> >
> > I really think this could either be supplied by the irqchip, or
> > somehow patched to avoid the pointless imux->ops->ipi_mux_send
> > indirection. Pointer chasing hurts.
>
> Once we remove ipi_mux_pre/post_handle() callbacks, the
> "ops" will be pointless and we will be able to remove one level
> of indirection here.
>
> We certainly need a mux irqchip to implement the
> mask/unmask semantics for muxed IPIs.
I'm not disputing that last point.
> > > +/**
> > > + * ipi_mux_create - Create virtual IPIs multiplexed on top of a single
> > > + * parent IPI.
> > > + * @parent_virq: virq of the parent per-CPU IRQ
> > > + * @nr_ipi: number of virtual IPIs to create. This should
> > > + * be <= BITS_PER_TYPE(int)
> > > + * @ops: multiplexing operations for the parent IPI
> > > + * @data: opaque data used by the multiplexing operations
> >
> > What is the use for data? If anything, that data should be passed via
> > the mux interrupt. But the whole point of this is to make the mux
> > invisible. So this whole 'data' business is a mystery to me.
>
> This is added only to pass back driver data in ipi_mux_send().
Again, what is the purpose of such data? If you need per-interrupt
data, this should be provided by the requester of the interrupt.
M.
--
Without deviation from the norm, progress is not possible.
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply [flat|nested] 12+ messages in thread* Re: [PATCH v11 3/7] genirq: Add mechanism to multiplex a single HW IPI
2022-11-26 14:28 ` Marc Zyngier
@ 2022-11-26 16:00 ` Anup Patel
0 siblings, 0 replies; 12+ messages in thread
From: Anup Patel @ 2022-11-26 16:00 UTC (permalink / raw)
To: Marc Zyngier
Cc: Palmer Dabbelt, Paul Walmsley, Thomas Gleixner, Daniel Lezcano,
Atish Patra, Alistair Francis, Anup Patel, linux-riscv,
linux-kernel
On Sat, Nov 26, 2022 at 7:58 PM Marc Zyngier <maz@kernel.org> wrote:
>
> On Sat, 26 Nov 2022 13:31:46 +0000,
> Anup Patel <apatel@ventanamicro.com> wrote:
> >
> > On Sat, Nov 26, 2022 at 6:12 PM Marc Zyngier <maz@kernel.org> wrote:
> > >
> > > On Mon, 14 Nov 2022 09:39:00 +0000,
> > > Anup Patel <apatel@ventanamicro.com> wrote:
> > > >
> > > > +struct ipi_mux_control {
> > > > + void *data;
> > > > + unsigned int nr;
> > >
> > > Honestly, I think we can get rid of this. The number of IPIs Linux
> > > uses is pretty small, and assuming a huge value (like 32) would be
> > > enough. It would save looking up this value on each IPI handling.
> >
> > I had kept in-case some driver wanted to create fewer (< 32)
> > muxed IPIs.
>
> I'm fine with being able to specifying the max, but I'm not sure there
> is a need to keep track of it any further. Certainly, the overhead of
> loading this value on each IPI could be removed. On most architecture,
> for_each_set_bit() and co and better optimised with a fixed number of
> bits.
Okay, I will update like you suggested.
>
> > > > +static const struct irq_chip ipi_mux_chip = {
> > > > + .name = "IPI Mux",
> > > > + .irq_mask = ipi_mux_mask,
> > > > + .irq_unmask = ipi_mux_unmask,
> > > > + .ipi_send_mask = ipi_mux_send_mask,
> > > > +};
> > >
> > > I really think this could either be supplied by the irqchip, or
> > > somehow patched to avoid the pointless imux->ops->ipi_mux_send
> > > indirection. Pointer chasing hurts.
> >
> > Once we remove ipi_mux_pre/post_handle() callbacks, the
> > "ops" will be pointless and we will be able to remove one level
> > of indirection here.
> >
> > We certainly need a mux irqchip to implement the
> > mask/unmask semantics for muxed IPIs.
>
> I'm not disputing that last point.
>
> > > > +/**
> > > > + * ipi_mux_create - Create virtual IPIs multiplexed on top of a single
> > > > + * parent IPI.
> > > > + * @parent_virq: virq of the parent per-CPU IRQ
> > > > + * @nr_ipi: number of virtual IPIs to create. This should
> > > > + * be <= BITS_PER_TYPE(int)
> > > > + * @ops: multiplexing operations for the parent IPI
> > > > + * @data: opaque data used by the multiplexing operations
> > >
> > > What is the use for data? If anything, that data should be passed via
> > > the mux interrupt. But the whole point of this is to make the mux
> > > invisible. So this whole 'data' business is a mystery to me.
> >
> > This is added only to pass back driver data in ipi_mux_send().
>
> Again, what is the purpose of such data? If you need per-interrupt
> data, this should be provided by the requester of the interrupt.
Currently, the irqchip drivers that we care about don't need this
data pointer so I will remove it. If required we can add it in future.
>
> M.
>
> --
> Without deviation from the norm, progress is not possible.
Thanks,
Anup
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v11 4/7] RISC-V: Treat IPIs as normal Linux IRQs
2022-11-14 9:38 [PATCH v11 0/7] RISC-V IPI Improvements Anup Patel
` (2 preceding siblings ...)
2022-11-14 9:39 ` [PATCH v11 3/7] genirq: Add mechanism to multiplex a single HW IPI Anup Patel
@ 2022-11-14 9:39 ` Anup Patel
2022-11-14 9:39 ` [PATCH v11 5/7] RISC-V: Allow marking IPIs as suitable for remote FENCEs Anup Patel
` (2 subsequent siblings)
6 siblings, 0 replies; 12+ messages in thread
From: Anup Patel @ 2022-11-14 9:39 UTC (permalink / raw)
To: Palmer Dabbelt, Paul Walmsley, Thomas Gleixner, Marc Zyngier,
Daniel Lezcano
Cc: Atish Patra, Alistair Francis, Anup Patel, linux-riscv,
linux-kernel, Anup Patel
Currently, the RISC-V kernel provides arch specific hooks (i.e.
struct riscv_ipi_ops) to register IPI handling methods. The stats
gathering of IPIs is also arch specific in the RISC-V kernel.
Other architectures (such as ARM, ARM64, and MIPS) have moved away
from custom arch specific IPI handling methods. Currently, these
architectures have Linux irqchip drivers providing a range of Linux
IRQ numbers to be used as IPIs and IPI triggering is done using
generic IPI APIs. This approach allows architectures to treat IPIs
as normal Linux IRQs and IPI stats gathering is done by the generic
Linux IRQ subsystem.
We extend the RISC-V IPI handling as-per above approach so that arch
specific IPI handling methods (struct riscv_ipi_ops) can be removed
and the IPI handling is done through the Linux IRQ subsystem.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
---
arch/riscv/Kconfig | 2 +
arch/riscv/include/asm/sbi.h | 7 ++
arch/riscv/include/asm/smp.h | 35 ++++---
arch/riscv/kernel/Makefile | 1 +
arch/riscv/kernel/cpu-hotplug.c | 3 +-
arch/riscv/kernel/irq.c | 3 +-
arch/riscv/kernel/sbi-ipi.c | 80 +++++++++++++++
arch/riscv/kernel/sbi.c | 17 ----
arch/riscv/kernel/smp.c | 155 +++++++++++++++---------------
arch/riscv/kernel/smpboot.c | 5 +-
drivers/clocksource/timer-clint.c | 43 ++++++---
drivers/irqchip/irq-riscv-intc.c | 55 +++++------
12 files changed, 251 insertions(+), 155 deletions(-)
create mode 100644 arch/riscv/kernel/sbi-ipi.c
diff --git a/arch/riscv/Kconfig b/arch/riscv/Kconfig
index c0e22648bd16..2fc20a189425 100644
--- a/arch/riscv/Kconfig
+++ b/arch/riscv/Kconfig
@@ -61,6 +61,8 @@ config RISCV
select GENERIC_GETTIMEOFDAY if HAVE_GENERIC_VDSO
select GENERIC_IDLE_POLL_SETUP
select GENERIC_IOREMAP if MMU
+ select GENERIC_IRQ_IPI if SMP
+ select GENERIC_IRQ_IPI_MUX if SMP
select GENERIC_IRQ_MULTI_HANDLER
select GENERIC_IRQ_SHOW
select GENERIC_IRQ_SHOW_LEVEL
diff --git a/arch/riscv/include/asm/sbi.h b/arch/riscv/include/asm/sbi.h
index 2a0ef738695e..c43f115714a0 100644
--- a/arch/riscv/include/asm/sbi.h
+++ b/arch/riscv/include/asm/sbi.h
@@ -327,4 +327,11 @@ int sbi_err_map_linux_errno(int err);
static inline int sbi_remote_fence_i(const struct cpumask *cpu_mask) { return -1; }
static inline void sbi_init(void) {}
#endif /* CONFIG_RISCV_SBI */
+
+#if IS_ENABLED(CONFIG_SMP) && IS_ENABLED(CONFIG_RISCV_SBI)
+void sbi_ipi_init(void);
+#else
+static inline void sbi_ipi_init(void) { }
+#endif
+
#endif /* _ASM_RISCV_SBI_H */
diff --git a/arch/riscv/include/asm/smp.h b/arch/riscv/include/asm/smp.h
index d3443be7eedc..79ed0b73cd4e 100644
--- a/arch/riscv/include/asm/smp.h
+++ b/arch/riscv/include/asm/smp.h
@@ -15,11 +15,6 @@
struct seq_file;
extern unsigned long boot_cpu_hartid;
-struct riscv_ipi_ops {
- void (*ipi_inject)(const struct cpumask *target);
- void (*ipi_clear)(void);
-};
-
#ifdef CONFIG_SMP
/*
* Mapping between linux logical cpu index and hartid.
@@ -33,9 +28,6 @@ void show_ipi_stats(struct seq_file *p, int prec);
/* SMP initialization hook for setup_arch */
void __init setup_smp(void);
-/* Called from C code, this handles an IPI. */
-void handle_IPI(struct pt_regs *regs);
-
/* Hook for the generic smp_call_function_many() routine. */
void arch_send_call_function_ipi_mask(struct cpumask *mask);
@@ -44,11 +36,17 @@ void arch_send_call_function_single_ipi(int cpu);
int riscv_hartid_to_cpuid(unsigned long hartid);
-/* Set custom IPI operations */
-void riscv_set_ipi_ops(const struct riscv_ipi_ops *ops);
+/* Enable IPI for CPU hotplug */
+void riscv_ipi_enable(void);
+
+/* Disable IPI for CPU hotplug */
+void riscv_ipi_disable(void);
-/* Clear IPI for current CPU */
-void riscv_clear_ipi(void);
+/* Check if IPI interrupt numbers are available */
+bool riscv_ipi_have_virq_range(void);
+
+/* Set the IPI interrupt numbers for arch (called by irqchip drivers) */
+void riscv_ipi_set_virq_range(int virq, int nr);
/* Secondary hart entry */
asmlinkage void smp_callin(void);
@@ -82,11 +80,20 @@ static inline unsigned long cpuid_to_hartid_map(int cpu)
return boot_cpu_hartid;
}
-static inline void riscv_set_ipi_ops(const struct riscv_ipi_ops *ops)
+static inline void riscv_ipi_enable(void)
{
}
-static inline void riscv_clear_ipi(void)
+static inline void riscv_ipi_disable(void)
+{
+}
+
+static inline bool riscv_ipi_have_virq_range(void)
+{
+ return false;
+}
+
+static inline void riscv_ipi_set_virq_range(int virq, int nr)
{
}
diff --git a/arch/riscv/kernel/Makefile b/arch/riscv/kernel/Makefile
index db6e4b1294ba..939f60f971a4 100644
--- a/arch/riscv/kernel/Makefile
+++ b/arch/riscv/kernel/Makefile
@@ -74,6 +74,7 @@ obj-$(CONFIG_PERF_EVENTS) += perf_callchain.o
obj-$(CONFIG_HAVE_PERF_REGS) += perf_regs.o
obj-$(CONFIG_RISCV_SBI) += sbi.o
ifeq ($(CONFIG_RISCV_SBI), y)
+obj-$(CONFIG_SMP) += sbi-ipi.o
obj-$(CONFIG_SMP) += cpu_ops_sbi.o
endif
obj-$(CONFIG_HOTPLUG_CPU) += cpu-hotplug.o
diff --git a/arch/riscv/kernel/cpu-hotplug.c b/arch/riscv/kernel/cpu-hotplug.c
index f7a832e3a1d1..39235cf50652 100644
--- a/arch/riscv/kernel/cpu-hotplug.c
+++ b/arch/riscv/kernel/cpu-hotplug.c
@@ -13,7 +13,7 @@
#include <asm/irq.h>
#include <asm/cpu_ops.h>
#include <asm/numa.h>
-#include <asm/sbi.h>
+#include <asm/smp.h>
bool cpu_has_hotplug(unsigned int cpu)
{
@@ -43,6 +43,7 @@ int __cpu_disable(void)
remove_cpu_topology(cpu);
numa_remove_cpu(cpu);
set_cpu_online(cpu, false);
+ riscv_ipi_disable();
irq_migrate_all_off_this_cpu();
return ret;
diff --git a/arch/riscv/kernel/irq.c b/arch/riscv/kernel/irq.c
index 96d3171f0ca1..eb9a68a539e6 100644
--- a/arch/riscv/kernel/irq.c
+++ b/arch/riscv/kernel/irq.c
@@ -10,7 +10,7 @@
#include <linux/irqdomain.h>
#include <linux/module.h>
#include <linux/seq_file.h>
-#include <asm/smp.h>
+#include <asm/sbi.h>
static struct fwnode_handle *(*__get_intc_node)(void);
@@ -39,4 +39,5 @@ void __init init_IRQ(void)
irqchip_init();
if (!handle_arch_irq)
panic("No interrupt controller found.");
+ sbi_ipi_init();
}
diff --git a/arch/riscv/kernel/sbi-ipi.c b/arch/riscv/kernel/sbi-ipi.c
new file mode 100644
index 000000000000..f0a78420b127
--- /dev/null
+++ b/arch/riscv/kernel/sbi-ipi.c
@@ -0,0 +1,80 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Multiplex several IPIs over a single HW IPI.
+ *
+ * Copyright (c) 2022 Ventana Micro Systems Inc.
+ */
+
+#define pr_fmt(fmt) "riscv: " fmt
+#include <linux/cpu.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <asm/sbi.h>
+
+static int sbi_ipi_virq;
+
+static void sbi_send_cpumask_ipi(unsigned int parent_virq, void *data,
+ const struct cpumask *target)
+{
+ sbi_send_ipi(target);
+}
+
+static void sbi_ipi_clear(unsigned int parent_virq, void *data)
+{
+ csr_clear(CSR_IP, IE_SIE);
+}
+
+static struct ipi_mux_ops sbi_ipi_ops = {
+ .ipi_mux_pre_handle = sbi_ipi_clear,
+ .ipi_mux_send = sbi_send_cpumask_ipi,
+};
+
+static int sbi_ipi_dying_cpu(unsigned int cpu)
+{
+ disable_percpu_irq(sbi_ipi_virq);
+ return 0;
+}
+
+static int sbi_ipi_starting_cpu(unsigned int cpu)
+{
+ enable_percpu_irq(sbi_ipi_virq, irq_get_trigger_type(sbi_ipi_virq));
+ return 0;
+}
+
+void __init sbi_ipi_init(void)
+{
+ int virq;
+ struct irq_domain *domain;
+
+ if (riscv_ipi_have_virq_range())
+ return;
+
+ domain = irq_find_matching_fwnode(riscv_get_intc_hwnode(),
+ DOMAIN_BUS_ANY);
+ if (!domain) {
+ pr_err("unable to find INTC IRQ domain\n");
+ return;
+ }
+
+ sbi_ipi_virq = irq_create_mapping(domain, RV_IRQ_SOFT);
+ if (!sbi_ipi_virq) {
+ pr_err("unable to create INTC IRQ mapping\n");
+ return;
+ }
+
+ virq = ipi_mux_create(sbi_ipi_virq, BITS_PER_BYTE,
+ &sbi_ipi_ops, NULL);
+ if (virq <= 0) {
+ pr_err("unable to create muxed IPIs\n");
+ irq_dispose_mapping(sbi_ipi_virq);
+ return;
+ }
+
+ cpuhp_setup_state(CPUHP_AP_ONLINE_DYN,
+ "irqchip/sbi-ipi:starting",
+ sbi_ipi_starting_cpu, sbi_ipi_dying_cpu);
+
+ riscv_ipi_set_virq_range(virq, BITS_PER_BYTE);
+ pr_info("providing IPIs using SBI IPI extension\n");
+}
diff --git a/arch/riscv/kernel/sbi.c b/arch/riscv/kernel/sbi.c
index fc614650a2e3..e9f04eba0e09 100644
--- a/arch/riscv/kernel/sbi.c
+++ b/arch/riscv/kernel/sbi.c
@@ -638,21 +638,6 @@ long sbi_get_mimpid(void)
return __sbi_base_ecall(SBI_EXT_BASE_GET_MIMPID);
}
-static void sbi_send_cpumask_ipi(const struct cpumask *target)
-{
- sbi_send_ipi(target);
-}
-
-static void sbi_ipi_clear(void)
-{
- csr_clear(CSR_IP, IE_SIE);
-}
-
-static const struct riscv_ipi_ops sbi_ipi_ops = {
- .ipi_inject = sbi_send_cpumask_ipi,
- .ipi_clear = sbi_ipi_clear
-};
-
void __init sbi_init(void)
{
int ret;
@@ -699,6 +684,4 @@ void __init sbi_init(void)
__sbi_send_ipi = __sbi_send_ipi_v01;
__sbi_rfence = __sbi_rfence_v01;
}
-
- riscv_set_ipi_ops(&sbi_ipi_ops);
}
diff --git a/arch/riscv/kernel/smp.c b/arch/riscv/kernel/smp.c
index c56d67f53ea9..e8a20454d65b 100644
--- a/arch/riscv/kernel/smp.c
+++ b/arch/riscv/kernel/smp.c
@@ -12,14 +12,15 @@
#include <linux/clockchips.h>
#include <linux/interrupt.h>
#include <linux/module.h>
+#include <linux/percpu.h>
#include <linux/profile.h>
#include <linux/smp.h>
#include <linux/sched.h>
#include <linux/seq_file.h>
#include <linux/delay.h>
+#include <linux/irq.h>
#include <linux/irq_work.h>
-#include <asm/sbi.h>
#include <asm/tlbflush.h>
#include <asm/cacheflush.h>
@@ -41,11 +42,10 @@ void __init smp_setup_processor_id(void)
cpuid_to_hartid_map(0) = boot_cpu_hartid;
}
-/* A collection of single bit ipi messages. */
-static struct {
- unsigned long stats[IPI_MAX] ____cacheline_aligned;
- unsigned long bits ____cacheline_aligned;
-} ipi_data[NR_CPUS] __cacheline_aligned;
+static DEFINE_PER_CPU_READ_MOSTLY(int, ipi_dummy_dev);
+static int ipi_virq_base __ro_after_init;
+static int nr_ipi __ro_after_init = IPI_MAX;
+static struct irq_desc *ipi_desc[IPI_MAX] __read_mostly;
int riscv_hartid_to_cpuid(unsigned long hartid)
{
@@ -71,46 +71,14 @@ static void ipi_stop(void)
wait_for_interrupt();
}
-static const struct riscv_ipi_ops *ipi_ops __ro_after_init;
-
-void riscv_set_ipi_ops(const struct riscv_ipi_ops *ops)
-{
- ipi_ops = ops;
-}
-EXPORT_SYMBOL_GPL(riscv_set_ipi_ops);
-
-void riscv_clear_ipi(void)
-{
- if (ipi_ops && ipi_ops->ipi_clear)
- ipi_ops->ipi_clear();
-}
-EXPORT_SYMBOL_GPL(riscv_clear_ipi);
-
static void send_ipi_mask(const struct cpumask *mask, enum ipi_message_type op)
{
- int cpu;
-
- smp_mb__before_atomic();
- for_each_cpu(cpu, mask)
- set_bit(op, &ipi_data[cpu].bits);
- smp_mb__after_atomic();
-
- if (ipi_ops && ipi_ops->ipi_inject)
- ipi_ops->ipi_inject(mask);
- else
- pr_warn("SMP: IPI inject method not available\n");
+ __ipi_send_mask(ipi_desc[op], mask);
}
static void send_ipi_single(int cpu, enum ipi_message_type op)
{
- smp_mb__before_atomic();
- set_bit(op, &ipi_data[cpu].bits);
- smp_mb__after_atomic();
-
- if (ipi_ops && ipi_ops->ipi_inject)
- ipi_ops->ipi_inject(cpumask_of(cpu));
- else
- pr_warn("SMP: IPI inject method not available\n");
+ __ipi_send_mask(ipi_desc[op], cpumask_of(cpu));
}
#ifdef CONFIG_IRQ_WORK
@@ -120,55 +88,88 @@ void arch_irq_work_raise(void)
}
#endif
-void handle_IPI(struct pt_regs *regs)
+static irqreturn_t handle_IPI(int irq, void *data)
+{
+ int ipi = irq - ipi_virq_base;
+
+ switch (ipi) {
+ case IPI_RESCHEDULE:
+ scheduler_ipi();
+ break;
+ case IPI_CALL_FUNC:
+ generic_smp_call_function_interrupt();
+ break;
+ case IPI_CPU_STOP:
+ ipi_stop();
+ break;
+ case IPI_IRQ_WORK:
+ irq_work_run();
+ break;
+#ifdef CONFIG_GENERIC_CLOCKEVENTS_BROADCAST
+ case IPI_TIMER:
+ tick_receive_broadcast();
+ break;
+#endif
+ default:
+ pr_warn("CPU%d: unhandled IPI%d\n", smp_processor_id(), ipi);
+ break;
+ };
+
+ return IRQ_HANDLED;
+}
+
+void riscv_ipi_enable(void)
{
- unsigned long *pending_ipis = &ipi_data[smp_processor_id()].bits;
- unsigned long *stats = ipi_data[smp_processor_id()].stats;
+ int i;
- riscv_clear_ipi();
+ if (WARN_ON_ONCE(!ipi_virq_base))
+ return;
- while (true) {
- unsigned long ops;
+ for (i = 0; i < nr_ipi; i++)
+ enable_percpu_irq(ipi_virq_base + i, 0);
+}
- /* Order bit clearing and data access. */
- mb();
+void riscv_ipi_disable(void)
+{
+ int i;
- ops = xchg(pending_ipis, 0);
- if (ops == 0)
- return;
+ if (WARN_ON_ONCE(!ipi_virq_base))
+ return;
- if (ops & (1 << IPI_RESCHEDULE)) {
- stats[IPI_RESCHEDULE]++;
- scheduler_ipi();
- }
+ for (i = 0; i < nr_ipi; i++)
+ disable_percpu_irq(ipi_virq_base + i);
+}
- if (ops & (1 << IPI_CALL_FUNC)) {
- stats[IPI_CALL_FUNC]++;
- generic_smp_call_function_interrupt();
- }
+bool riscv_ipi_have_virq_range(void)
+{
+ return (ipi_virq_base) ? true : false;
+}
- if (ops & (1 << IPI_CPU_STOP)) {
- stats[IPI_CPU_STOP]++;
- ipi_stop();
- }
+void riscv_ipi_set_virq_range(int virq, int nr)
+{
+ int i, err;
- if (ops & (1 << IPI_IRQ_WORK)) {
- stats[IPI_IRQ_WORK]++;
- irq_work_run();
- }
+ if (WARN_ON(ipi_virq_base))
+ return;
-#ifdef CONFIG_GENERIC_CLOCKEVENTS_BROADCAST
- if (ops & (1 << IPI_TIMER)) {
- stats[IPI_TIMER]++;
- tick_receive_broadcast();
- }
-#endif
- BUG_ON((ops >> IPI_MAX) != 0);
+ WARN_ON(nr < IPI_MAX);
+ nr_ipi = min(nr, IPI_MAX);
+ ipi_virq_base = virq;
+
+ /* Request IPIs */
+ for (i = 0; i < nr_ipi; i++) {
+ err = request_percpu_irq(ipi_virq_base + i, handle_IPI,
+ "IPI", &ipi_dummy_dev);
+ WARN_ON(err);
- /* Order data access and bit testing. */
- mb();
+ ipi_desc[i] = irq_to_desc(ipi_virq_base + i);
+ irq_set_status_flags(ipi_virq_base + i, IRQ_HIDDEN);
}
+
+ /* Enabled IPIs for boot CPU immediately */
+ riscv_ipi_enable();
}
+EXPORT_SYMBOL_GPL(riscv_ipi_set_virq_range);
static const char * const ipi_names[] = {
[IPI_RESCHEDULE] = "Rescheduling interrupts",
@@ -186,7 +187,7 @@ void show_ipi_stats(struct seq_file *p, int prec)
seq_printf(p, "%*s%u:%s", prec - 1, "IPI", i,
prec >= 4 ? " " : "");
for_each_online_cpu(cpu)
- seq_printf(p, "%10lu ", ipi_data[cpu].stats[i]);
+ seq_printf(p, "%10u ", irq_desc_kstat_cpu(ipi_desc[i], cpu));
seq_printf(p, " %s\n", ipi_names[i]);
}
}
diff --git a/arch/riscv/kernel/smpboot.c b/arch/riscv/kernel/smpboot.c
index 3373df413c88..9cbdb960515b 100644
--- a/arch/riscv/kernel/smpboot.c
+++ b/arch/riscv/kernel/smpboot.c
@@ -30,7 +30,6 @@
#include <asm/numa.h>
#include <asm/tlbflush.h>
#include <asm/sections.h>
-#include <asm/sbi.h>
#include <asm/smp.h>
#include "head.h"
@@ -157,12 +156,12 @@ asmlinkage __visible void smp_callin(void)
struct mm_struct *mm = &init_mm;
unsigned int curr_cpuid = smp_processor_id();
- riscv_clear_ipi();
-
/* All kernel threads share the same mm context. */
mmgrab(mm);
current->active_mm = mm;
+ riscv_ipi_enable();
+
store_cpu_topology(curr_cpuid);
notify_cpu_starting(curr_cpuid);
numa_add_cpu(curr_cpuid);
diff --git a/drivers/clocksource/timer-clint.c b/drivers/clocksource/timer-clint.c
index 6cfe2ab73eb0..f9dd746a72c5 100644
--- a/drivers/clocksource/timer-clint.c
+++ b/drivers/clocksource/timer-clint.c
@@ -17,6 +17,8 @@
#include <linux/sched_clock.h>
#include <linux/io-64-nonatomic-lo-hi.h>
#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
#include <linux/of_irq.h>
#include <linux/smp.h>
#include <linux/timex.h>
@@ -31,6 +33,7 @@
/* CLINT manages IPI and Timer for RISC-V M-mode */
static u32 __iomem *clint_ipi_base;
+static unsigned int clint_ipi_irq;
static u64 __iomem *clint_timer_cmp;
static u64 __iomem *clint_timer_val;
static unsigned long clint_timer_freq;
@@ -41,7 +44,8 @@ u64 __iomem *clint_time_val;
EXPORT_SYMBOL(clint_time_val);
#endif
-static void clint_send_ipi(const struct cpumask *target)
+static void clint_send_ipi(unsigned int parent_virq, void *data,
+ const struct cpumask *target)
{
unsigned int cpu;
@@ -49,14 +53,14 @@ static void clint_send_ipi(const struct cpumask *target)
writel(1, clint_ipi_base + cpuid_to_hartid_map(cpu));
}
-static void clint_clear_ipi(void)
+static void clint_clear_ipi(unsigned int parent_virq, void *data)
{
writel(0, clint_ipi_base + cpuid_to_hartid_map(smp_processor_id()));
}
-static struct riscv_ipi_ops clint_ipi_ops = {
- .ipi_inject = clint_send_ipi,
- .ipi_clear = clint_clear_ipi,
+static struct ipi_mux_ops clint_ipi_ops = {
+ .ipi_mux_pre_handle = clint_clear_ipi,
+ .ipi_mux_send = clint_send_ipi,
};
#ifdef CONFIG_64BIT
@@ -125,12 +129,15 @@ static int clint_timer_starting_cpu(unsigned int cpu)
enable_percpu_irq(clint_timer_irq,
irq_get_trigger_type(clint_timer_irq));
+ enable_percpu_irq(clint_ipi_irq,
+ irq_get_trigger_type(clint_ipi_irq));
return 0;
}
static int clint_timer_dying_cpu(unsigned int cpu)
{
disable_percpu_irq(clint_timer_irq);
+ disable_percpu_irq(clint_ipi_irq);
return 0;
}
@@ -146,7 +153,7 @@ static irqreturn_t clint_timer_interrupt(int irq, void *dev_id)
static int __init clint_timer_init_dt(struct device_node *np)
{
- int rc;
+ int rc, virq;
u32 i, nr_irqs;
void __iomem *base;
struct of_phandle_args oirq;
@@ -170,6 +177,12 @@ static int __init clint_timer_init_dt(struct device_node *np)
return -ENODEV;
}
+ /* Find parent irq domain and map ipi irq */
+ if (!clint_ipi_irq &&
+ oirq.args[0] == RV_IRQ_SOFT &&
+ irq_find_host(oirq.np))
+ clint_ipi_irq = irq_of_parse_and_map(np, i);
+
/* Find parent irq domain and map timer irq */
if (!clint_timer_irq &&
oirq.args[0] == RV_IRQ_TIMER &&
@@ -177,9 +190,9 @@ static int __init clint_timer_init_dt(struct device_node *np)
clint_timer_irq = irq_of_parse_and_map(np, i);
}
- /* If CLINT timer irq not found then fail */
- if (!clint_timer_irq) {
- pr_err("%pOFP: timer irq not found\n", np);
+ /* If CLINT ipi or timer irq not found then fail */
+ if (!clint_ipi_irq || !clint_timer_irq) {
+ pr_err("%pOFP: ipi/timer irq not found\n", np);
return -ENODEV;
}
@@ -219,6 +232,14 @@ static int __init clint_timer_init_dt(struct device_node *np)
goto fail_iounmap;
}
+ virq = ipi_mux_create(clint_ipi_irq, BITS_PER_BYTE,
+ &clint_ipi_ops, NULL);
+ if (virq <= 0) {
+ pr_err("unable to create muxed IPIs\n");
+ rc = (virq < 0) ? virq : -ENODEV;
+ goto fail_free_irq;
+ }
+
rc = cpuhp_setup_state(CPUHP_AP_CLINT_TIMER_STARTING,
"clockevents/clint/timer:starting",
clint_timer_starting_cpu,
@@ -228,8 +249,8 @@ static int __init clint_timer_init_dt(struct device_node *np)
goto fail_free_irq;
}
- riscv_set_ipi_ops(&clint_ipi_ops);
- clint_clear_ipi();
+ riscv_ipi_set_virq_range(virq, BITS_PER_BYTE);
+ clint_clear_ipi(clint_ipi_irq, NULL);
return 0;
diff --git a/drivers/irqchip/irq-riscv-intc.c b/drivers/irqchip/irq-riscv-intc.c
index 9066467e99e4..784d25645704 100644
--- a/drivers/irqchip/irq-riscv-intc.c
+++ b/drivers/irqchip/irq-riscv-intc.c
@@ -26,20 +26,7 @@ static asmlinkage void riscv_intc_irq(struct pt_regs *regs)
if (unlikely(cause >= BITS_PER_LONG))
panic("unexpected interrupt cause");
- switch (cause) {
-#ifdef CONFIG_SMP
- case RV_IRQ_SOFT:
- /*
- * We only use software interrupts to pass IPIs, so if a
- * non-SMP system gets one, then we don't know what to do.
- */
- handle_IPI(regs);
- break;
-#endif
- default:
- generic_handle_domain_irq(intc_domain, cause);
- break;
- }
+ generic_handle_domain_irq(intc_domain, cause);
}
/*
@@ -59,18 +46,6 @@ static void riscv_intc_irq_unmask(struct irq_data *d)
csr_set(CSR_IE, BIT(d->hwirq));
}
-static int riscv_intc_cpu_starting(unsigned int cpu)
-{
- csr_set(CSR_IE, BIT(RV_IRQ_SOFT));
- return 0;
-}
-
-static int riscv_intc_cpu_dying(unsigned int cpu)
-{
- csr_clear(CSR_IE, BIT(RV_IRQ_SOFT));
- return 0;
-}
-
static struct irq_chip riscv_intc_chip = {
.name = "RISC-V INTC",
.irq_mask = riscv_intc_irq_mask,
@@ -87,9 +62,32 @@ static int riscv_intc_domain_map(struct irq_domain *d, unsigned int irq,
return 0;
}
+static int riscv_intc_domain_alloc(struct irq_domain *domain,
+ unsigned int virq, unsigned int nr_irqs,
+ void *arg)
+{
+ int i, ret;
+ irq_hw_number_t hwirq;
+ unsigned int type = IRQ_TYPE_NONE;
+ struct irq_fwspec *fwspec = arg;
+
+ ret = irq_domain_translate_onecell(domain, fwspec, &hwirq, &type);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < nr_irqs; i++) {
+ ret = riscv_intc_domain_map(domain, virq + i, hwirq + i);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
static const struct irq_domain_ops riscv_intc_domain_ops = {
.map = riscv_intc_domain_map,
.xlate = irq_domain_xlate_onecell,
+ .alloc = riscv_intc_domain_alloc
};
static struct fwnode_handle *riscv_intc_hwnode(void)
@@ -133,11 +131,6 @@ static int __init riscv_intc_init(struct device_node *node,
riscv_set_intc_hwnode_fn(riscv_intc_hwnode);
- cpuhp_setup_state(CPUHP_AP_IRQ_RISCV_STARTING,
- "irqchip/riscv/intc:starting",
- riscv_intc_cpu_starting,
- riscv_intc_cpu_dying);
-
pr_info("%d local interrupts mapped\n", BITS_PER_LONG);
return 0;
--
2.34.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v11 5/7] RISC-V: Allow marking IPIs as suitable for remote FENCEs
2022-11-14 9:38 [PATCH v11 0/7] RISC-V IPI Improvements Anup Patel
` (3 preceding siblings ...)
2022-11-14 9:39 ` [PATCH v11 4/7] RISC-V: Treat IPIs as normal Linux IRQs Anup Patel
@ 2022-11-14 9:39 ` Anup Patel
2022-11-14 9:39 ` [PATCH v11 6/7] RISC-V: Use IPIs for remote TLB flush when possible Anup Patel
2022-11-14 9:39 ` [PATCH v11 7/7] RISC-V: Use IPIs for remote icache " Anup Patel
6 siblings, 0 replies; 12+ messages in thread
From: Anup Patel @ 2022-11-14 9:39 UTC (permalink / raw)
To: Palmer Dabbelt, Paul Walmsley, Thomas Gleixner, Marc Zyngier,
Daniel Lezcano
Cc: Atish Patra, Alistair Francis, Anup Patel, linux-riscv,
linux-kernel, Anup Patel, Atish Patra
To do remote FENCEs (i.e. remote TLB flushes) using IPI calls on the
RISC-V kernel, we need hardware mechanism to directly inject IPI from
the supervisor mode (i.e. RISC-V kernel) instead of using SBI calls.
The upcoming AIA IMSIC devices allow direct IPI injection from the
supervisor mode (i.e. RISC-V kernel). To support this, we extend the
riscv_ipi_set_virq_range() function so that IPI provider (i.e. irqchip
drivers can mark IPIs as suitable for remote FENCEs.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
---
arch/riscv/include/asm/smp.h | 18 ++++++++++++++++--
arch/riscv/kernel/sbi-ipi.c | 2 +-
arch/riscv/kernel/smp.c | 11 ++++++++++-
drivers/clocksource/timer-clint.c | 2 +-
4 files changed, 28 insertions(+), 5 deletions(-)
diff --git a/arch/riscv/include/asm/smp.h b/arch/riscv/include/asm/smp.h
index 79ed0b73cd4e..56976e41a21e 100644
--- a/arch/riscv/include/asm/smp.h
+++ b/arch/riscv/include/asm/smp.h
@@ -16,6 +16,9 @@ struct seq_file;
extern unsigned long boot_cpu_hartid;
#ifdef CONFIG_SMP
+
+#include <linux/jump_label.h>
+
/*
* Mapping between linux logical cpu index and hartid.
*/
@@ -46,7 +49,12 @@ void riscv_ipi_disable(void);
bool riscv_ipi_have_virq_range(void);
/* Set the IPI interrupt numbers for arch (called by irqchip drivers) */
-void riscv_ipi_set_virq_range(int virq, int nr);
+void riscv_ipi_set_virq_range(int virq, int nr, bool use_for_rfence);
+
+/* Check if we can use IPIs for remote FENCEs */
+DECLARE_STATIC_KEY_FALSE(riscv_ipi_for_rfence);
+#define riscv_use_ipi_for_rfence() \
+ static_branch_unlikely(&riscv_ipi_for_rfence)
/* Secondary hart entry */
asmlinkage void smp_callin(void);
@@ -93,10 +101,16 @@ static inline bool riscv_ipi_have_virq_range(void)
return false;
}
-static inline void riscv_ipi_set_virq_range(int virq, int nr)
+static inline void riscv_ipi_set_virq_range(int virq, int nr,
+ bool use_for_rfence)
{
}
+static inline bool riscv_use_ipi_for_rfence(void)
+{
+ return false;
+}
+
#endif /* CONFIG_SMP */
#if defined(CONFIG_HOTPLUG_CPU) && (CONFIG_SMP)
diff --git a/arch/riscv/kernel/sbi-ipi.c b/arch/riscv/kernel/sbi-ipi.c
index f0a78420b127..ee8620104bd8 100644
--- a/arch/riscv/kernel/sbi-ipi.c
+++ b/arch/riscv/kernel/sbi-ipi.c
@@ -75,6 +75,6 @@ void __init sbi_ipi_init(void)
"irqchip/sbi-ipi:starting",
sbi_ipi_starting_cpu, sbi_ipi_dying_cpu);
- riscv_ipi_set_virq_range(virq, BITS_PER_BYTE);
+ riscv_ipi_set_virq_range(virq, BITS_PER_BYTE, false);
pr_info("providing IPIs using SBI IPI extension\n");
}
diff --git a/arch/riscv/kernel/smp.c b/arch/riscv/kernel/smp.c
index e8a20454d65b..74b8cb1a89ab 100644
--- a/arch/riscv/kernel/smp.c
+++ b/arch/riscv/kernel/smp.c
@@ -145,7 +145,10 @@ bool riscv_ipi_have_virq_range(void)
return (ipi_virq_base) ? true : false;
}
-void riscv_ipi_set_virq_range(int virq, int nr)
+DEFINE_STATIC_KEY_FALSE(riscv_ipi_for_rfence);
+EXPORT_SYMBOL_GPL(riscv_ipi_for_rfence);
+
+void riscv_ipi_set_virq_range(int virq, int nr, bool use_for_rfence)
{
int i, err;
@@ -168,6 +171,12 @@ void riscv_ipi_set_virq_range(int virq, int nr)
/* Enabled IPIs for boot CPU immediately */
riscv_ipi_enable();
+
+ /* Update RFENCE static key */
+ if (use_for_rfence)
+ static_branch_enable(&riscv_ipi_for_rfence);
+ else
+ static_branch_disable(&riscv_ipi_for_rfence);
}
EXPORT_SYMBOL_GPL(riscv_ipi_set_virq_range);
diff --git a/drivers/clocksource/timer-clint.c b/drivers/clocksource/timer-clint.c
index f9dd746a72c5..658049a5440b 100644
--- a/drivers/clocksource/timer-clint.c
+++ b/drivers/clocksource/timer-clint.c
@@ -249,7 +249,7 @@ static int __init clint_timer_init_dt(struct device_node *np)
goto fail_free_irq;
}
- riscv_ipi_set_virq_range(virq, BITS_PER_BYTE);
+ riscv_ipi_set_virq_range(virq, BITS_PER_BYTE, true);
clint_clear_ipi(clint_ipi_irq, NULL);
return 0;
--
2.34.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v11 6/7] RISC-V: Use IPIs for remote TLB flush when possible
2022-11-14 9:38 [PATCH v11 0/7] RISC-V IPI Improvements Anup Patel
` (4 preceding siblings ...)
2022-11-14 9:39 ` [PATCH v11 5/7] RISC-V: Allow marking IPIs as suitable for remote FENCEs Anup Patel
@ 2022-11-14 9:39 ` Anup Patel
2022-11-14 9:39 ` [PATCH v11 7/7] RISC-V: Use IPIs for remote icache " Anup Patel
6 siblings, 0 replies; 12+ messages in thread
From: Anup Patel @ 2022-11-14 9:39 UTC (permalink / raw)
To: Palmer Dabbelt, Paul Walmsley, Thomas Gleixner, Marc Zyngier,
Daniel Lezcano
Cc: Atish Patra, Alistair Francis, Anup Patel, linux-riscv,
linux-kernel, Anup Patel, Atish Patra
If we have specialized interrupt controller (such as AIA IMSIC) which
allows supervisor mode to directly inject IPIs without any assistance
from M-mode or HS-mode then using such specialized interrupt controller,
we can do remote TLB flushes directly from supervisor mode instead of
using the SBI RFENCE calls.
This patch extends remote TLB flush functions to use supervisor mode
IPIs whenever direct supervisor mode IPIs.are supported by interrupt
controller.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
---
arch/riscv/mm/tlbflush.c | 93 +++++++++++++++++++++++++++++++++-------
1 file changed, 78 insertions(+), 15 deletions(-)
diff --git a/arch/riscv/mm/tlbflush.c b/arch/riscv/mm/tlbflush.c
index 37ed760d007c..27a7db8eb2c4 100644
--- a/arch/riscv/mm/tlbflush.c
+++ b/arch/riscv/mm/tlbflush.c
@@ -23,14 +23,62 @@ static inline void local_flush_tlb_page_asid(unsigned long addr,
: "memory");
}
+static inline void local_flush_tlb_range(unsigned long start,
+ unsigned long size, unsigned long stride)
+{
+ if (size <= stride)
+ local_flush_tlb_page(start);
+ else
+ local_flush_tlb_all();
+}
+
+static inline void local_flush_tlb_range_asid(unsigned long start,
+ unsigned long size, unsigned long stride, unsigned long asid)
+{
+ if (size <= stride)
+ local_flush_tlb_page_asid(start, asid);
+ else
+ local_flush_tlb_all_asid(asid);
+}
+
+static void __ipi_flush_tlb_all(void *info)
+{
+ local_flush_tlb_all();
+}
+
void flush_tlb_all(void)
{
- sbi_remote_sfence_vma(NULL, 0, -1);
+ if (riscv_use_ipi_for_rfence())
+ on_each_cpu(__ipi_flush_tlb_all, NULL, 1);
+ else
+ sbi_remote_sfence_vma(NULL, 0, -1);
+}
+
+struct flush_tlb_range_data {
+ unsigned long asid;
+ unsigned long start;
+ unsigned long size;
+ unsigned long stride;
+};
+
+static void __ipi_flush_tlb_range_asid(void *info)
+{
+ struct flush_tlb_range_data *d = info;
+
+ local_flush_tlb_range_asid(d->start, d->size, d->stride, d->asid);
+}
+
+static void __ipi_flush_tlb_range(void *info)
+{
+ struct flush_tlb_range_data *d = info;
+
+ local_flush_tlb_range(d->start, d->size, d->stride);
}
-static void __sbi_tlb_flush_range(struct mm_struct *mm, unsigned long start,
- unsigned long size, unsigned long stride)
+static void __flush_tlb_range(struct mm_struct *mm, unsigned long start,
+ unsigned long size, unsigned long stride)
{
+ struct flush_tlb_range_data ftd;
struct cpumask *cmask = mm_cpumask(mm);
unsigned int cpuid;
bool broadcast;
@@ -45,19 +93,34 @@ static void __sbi_tlb_flush_range(struct mm_struct *mm, unsigned long start,
unsigned long asid = atomic_long_read(&mm->context.id);
if (broadcast) {
- sbi_remote_sfence_vma_asid(cmask, start, size, asid);
- } else if (size <= stride) {
- local_flush_tlb_page_asid(start, asid);
+ if (riscv_use_ipi_for_rfence()) {
+ ftd.asid = asid;
+ ftd.start = start;
+ ftd.size = size;
+ ftd.stride = stride;
+ on_each_cpu_mask(cmask,
+ __ipi_flush_tlb_range_asid,
+ &ftd, 1);
+ } else
+ sbi_remote_sfence_vma_asid(cmask,
+ start, size, asid);
} else {
- local_flush_tlb_all_asid(asid);
+ local_flush_tlb_range_asid(start, size, stride, asid);
}
} else {
if (broadcast) {
- sbi_remote_sfence_vma(cmask, start, size);
- } else if (size <= stride) {
- local_flush_tlb_page(start);
+ if (riscv_use_ipi_for_rfence()) {
+ ftd.asid = 0;
+ ftd.start = start;
+ ftd.size = size;
+ ftd.stride = stride;
+ on_each_cpu_mask(cmask,
+ __ipi_flush_tlb_range,
+ &ftd, 1);
+ } else
+ sbi_remote_sfence_vma(cmask, start, size);
} else {
- local_flush_tlb_all();
+ local_flush_tlb_range(start, size, stride);
}
}
@@ -66,23 +129,23 @@ static void __sbi_tlb_flush_range(struct mm_struct *mm, unsigned long start,
void flush_tlb_mm(struct mm_struct *mm)
{
- __sbi_tlb_flush_range(mm, 0, -1, PAGE_SIZE);
+ __flush_tlb_range(mm, 0, -1, PAGE_SIZE);
}
void flush_tlb_page(struct vm_area_struct *vma, unsigned long addr)
{
- __sbi_tlb_flush_range(vma->vm_mm, addr, PAGE_SIZE, PAGE_SIZE);
+ __flush_tlb_range(vma->vm_mm, addr, PAGE_SIZE, PAGE_SIZE);
}
void flush_tlb_range(struct vm_area_struct *vma, unsigned long start,
unsigned long end)
{
- __sbi_tlb_flush_range(vma->vm_mm, start, end - start, PAGE_SIZE);
+ __flush_tlb_range(vma->vm_mm, start, end - start, PAGE_SIZE);
}
#ifdef CONFIG_TRANSPARENT_HUGEPAGE
void flush_pmd_tlb_range(struct vm_area_struct *vma, unsigned long start,
unsigned long end)
{
- __sbi_tlb_flush_range(vma->vm_mm, start, end - start, PMD_SIZE);
+ __flush_tlb_range(vma->vm_mm, start, end - start, PMD_SIZE);
}
#endif
--
2.34.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v11 7/7] RISC-V: Use IPIs for remote icache flush when possible
2022-11-14 9:38 [PATCH v11 0/7] RISC-V IPI Improvements Anup Patel
` (5 preceding siblings ...)
2022-11-14 9:39 ` [PATCH v11 6/7] RISC-V: Use IPIs for remote TLB flush when possible Anup Patel
@ 2022-11-14 9:39 ` Anup Patel
6 siblings, 0 replies; 12+ messages in thread
From: Anup Patel @ 2022-11-14 9:39 UTC (permalink / raw)
To: Palmer Dabbelt, Paul Walmsley, Thomas Gleixner, Marc Zyngier,
Daniel Lezcano
Cc: Atish Patra, Alistair Francis, Anup Patel, linux-riscv,
linux-kernel, Anup Patel, Atish Patra
If we have specialized interrupt controller (such as AIA IMSIC) which
allows supervisor mode to directly inject IPIs without any assistance
from M-mode or HS-mode then using such specialized interrupt controller,
we can do remote icache flushe directly from supervisor mode instead of
using the SBI RFENCE calls.
This patch extends remote icache flush functions to use supervisor mode
IPIs whenever direct supervisor mode IPIs.are supported by interrupt
controller.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
---
arch/riscv/mm/cacheflush.c | 5 +++--
1 file changed, 3 insertions(+), 2 deletions(-)
diff --git a/arch/riscv/mm/cacheflush.c b/arch/riscv/mm/cacheflush.c
index 57b40a350420..f10cb47eac3a 100644
--- a/arch/riscv/mm/cacheflush.c
+++ b/arch/riscv/mm/cacheflush.c
@@ -19,7 +19,7 @@ void flush_icache_all(void)
{
local_flush_icache_all();
- if (IS_ENABLED(CONFIG_RISCV_SBI))
+ if (IS_ENABLED(CONFIG_RISCV_SBI) && !riscv_use_ipi_for_rfence())
sbi_remote_fence_i(NULL);
else
on_each_cpu(ipi_remote_fence_i, NULL, 1);
@@ -67,7 +67,8 @@ void flush_icache_mm(struct mm_struct *mm, bool local)
* with flush_icache_deferred().
*/
smp_mb();
- } else if (IS_ENABLED(CONFIG_RISCV_SBI)) {
+ } else if (IS_ENABLED(CONFIG_RISCV_SBI) &&
+ !riscv_use_ipi_for_rfence()) {
sbi_remote_fence_i(&others);
} else {
on_each_cpu_mask(&others, ipi_remote_fence_i, NULL, 1);
--
2.34.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 12+ messages in thread