Linux-SPI Archive on lore.kernel.org
 help / color / Atom feed
From: Michael Walle <michael@walle.cc>
To: Pratyush Yadav <p.yadav@ti.com>
Cc: Nishanth Menon <nm@ti.com>, Tero Kristo <kristo@kernel.org>,
	Rob Herring <robh+dt@kernel.org>,
	Tudor Ambarus <tudor.ambarus@microchip.com>,
	Miquel Raynal <miquel.raynal@bootlin.com>,
	Richard Weinberger <richard@nod.at>,
	Vignesh Raghavendra <vigneshr@ti.com>,
	Mark Brown <broonie@kernel.org>,
	linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-mtd@lists.infradead.org,
	linux-spi@vger.kernel.org, Lokesh Vutla <lokeshvutla@ti.com>
Subject: Re: [RFC PATCH 1/6] spi: spi-mem: Tell controller when device is ready for calibration
Date: Thu, 29 Apr 2021 18:23:50 +0200
Message-ID: <6dfbb3e4107887dc9ee3e19e4940e87c@walle.cc> (raw)
In-Reply-To: <20210324080804.x7oemmpt2khi72mp@ti.com>

Hi Pratyush,

I've had a look at the LS1028A FlexSPI calibration feature. The
reference manual is very sparse on details, though. What you need to
do there is to program a special read command sequence (the whole
controller is made of these lookup table entries, where you can
have a short sequence of operations for read/write/program and so
on). Therefore, for data learning you'll take the read operation
and insert a LEARN op in between and read a specific data pattern.
Then the hardware will automatically figure out the correct sample
phase for the read data pins.

Unfortunately, it does not mention how often you have to do it. It
might be the case that is has to be calibrated more than once.

I'm just mentioning this so it won't be lost. If needed, it can
be added later.

Am 2021-03-24 09:08, schrieb Pratyush Yadav:
> On 24/03/21 12:07AM, Michael Walle wrote:
>> Am 2021-03-11 20:12, schrieb Pratyush Yadav:
>> > Some controllers like the Cadence OSPI controller need to perform a
>> > calibration sequence to operate at high clock speeds. This calibration
>> > should happen after the flash is fully initialized otherwise the
>> > calibration might happen in a different SPI mode from the one the flash
>> > is finally set to. Add a hook that can be used to tell the controller
>> > when the flash is ready for calibration. Whether calibration is needed
>> > depends on the controller.
>> >
>> > Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
>> > ---
>> >  drivers/spi/spi-mem.c       | 12 ++++++++++++
>> >  include/linux/spi/spi-mem.h |  8 ++++++++
>> >  2 files changed, 20 insertions(+)
>> >
>> > diff --git a/drivers/spi/spi-mem.c b/drivers/spi/spi-mem.c
>> > index dc713b0c3c4d..e2f05ad3f4dc 100644
>> > --- a/drivers/spi/spi-mem.c
>> > +++ b/drivers/spi/spi-mem.c
>> > @@ -464,6 +464,18 @@ int spi_mem_adjust_op_size(struct spi_mem *mem,
>> > struct spi_mem_op *op)
>> >  }
>> >  EXPORT_SYMBOL_GPL(spi_mem_adjust_op_size);
>> >
>> > +int spi_mem_do_calibration(struct spi_mem *mem, struct spi_mem_op *op)
>> > +{
>> > +	struct spi_controller *ctlr = mem->spi->controller;
>> > +
>> > +	if (!ctlr->mem_ops || !ctlr->mem_ops->do_calibration)
>> > +		return -EOPNOTSUPP;
>> > +
>> > +	ctlr->mem_ops->do_calibration(mem, op);
>> 
>> Can't a calibration fail?
> 
> It can. If it does, the controller falls back to lower speed transfers.
> There is not much the upper layer can do about this. That's why it is
> not informed whether it succeeded or not.

Ok, if needed, that should be an easy change.

op is there to decide if we need a calibration at all, correct?
What if there are different factors, like frequency? For example
on the LS1028A its just a matter of the SCK frequency. It seems
that this parameter is tailored to the OPHY.

-michael

>> > +	return 0;
>> > +}
>> > +EXPORT_SYMBOL_GPL(spi_mem_do_calibration);
>> > +
>> >  static ssize_t spi_mem_no_dirmap_read(struct spi_mem_dirmap_desc *desc,
>> >  				      u64 offs, size_t len, void *buf)
>> >  {
>> > diff --git a/include/linux/spi/spi-mem.h b/include/linux/spi/spi-mem.h
>> > index 2b65c9edc34e..97a2d280f2d0 100644
>> > --- a/include/linux/spi/spi-mem.h
>> > +++ b/include/linux/spi/spi-mem.h
>> > @@ -250,6 +250,12 @@ static inline void *spi_mem_get_drvdata(struct
>> > spi_mem *mem)
>> >   *		  the currently mapped area), and the caller of
>> >   *		  spi_mem_dirmap_write() is responsible for calling it again in
>> >   *		  this case.
>> > + * @do_calibration: perform calibration needed for high SPI clock speed
>> > + *		    operation. Should be called after the SPI memory device has
>> > + *		    been completely initialized. The op passed should contain
>> > + *		    a template for the read operation used for the device so
>> > + *		    the controller can decide what type of calibration is
>> > + *		    required for this type of read.
>> >   *
>> >   * This interface should be implemented by SPI controllers providing an
>> >   * high-level interface to execute SPI memory operation, which is
>> > usually the
>> > @@ -274,6 +280,7 @@ struct spi_controller_mem_ops {
>> >  			       u64 offs, size_t len, void *buf);
>> >  	ssize_t (*dirmap_write)(struct spi_mem_dirmap_desc *desc,
>> >  				u64 offs, size_t len, const void *buf);
>> > +	void (*do_calibration)(struct spi_mem *mem, struct spi_mem_op *op);
>> >  };
>> >
>> >  /**
>> > @@ -346,6 +353,7 @@ bool spi_mem_dtr_supports_op(struct spi_mem *mem,
>> >  #endif /* CONFIG_SPI_MEM */
>> >
>> >  int spi_mem_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op);
>> > +int spi_mem_do_calibration(struct spi_mem *mem, struct spi_mem_op *op);
>> >
>> >  bool spi_mem_supports_op(struct spi_mem *mem,
>> >  			 const struct spi_mem_op *op);
>> 


  reply index

Thread overview: 33+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-03-11 19:12 [RFC PATCH 0/6] spi: Add OSPI PHY calibration support for spi-cadence-quadspi Pratyush Yadav
2021-03-11 19:12 ` [RFC PATCH 1/6] spi: spi-mem: Tell controller when device is ready for calibration Pratyush Yadav
2021-03-23 23:07   ` Michael Walle
2021-03-24  8:08     ` Pratyush Yadav
2021-04-29 16:23       ` Michael Walle [this message]
2021-04-29 18:41         ` Pratyush Yadav
2021-04-29 22:46           ` Michael Walle
2021-03-11 19:12 ` [RFC PATCH 2/6] mtd: spi-nor: core: consolidate read op creation Pratyush Yadav
2021-03-23 23:17   ` Michael Walle
2021-03-24  8:04     ` Pratyush Yadav
2021-04-08 12:48   ` Michael Walle
2021-03-11 19:12 ` [RFC PATCH 3/6] mtd: spi-nor: core: run calibration when initialization is done Pratyush Yadav
2021-03-11 19:12 ` [RFC PATCH 4/6] spi: cadence-qspi: Use PHY for DAC reads if possible Pratyush Yadav
2021-03-12  9:13   ` Tudor.Ambarus
2021-03-12 10:17     ` Pratyush Yadav
2021-04-29 16:28       ` Michael Walle
2021-04-29 18:19         ` Pratyush Yadav
2021-04-29 22:20           ` Michael Walle
2021-05-10 11:39             ` Pratyush Yadav
2021-03-11 19:12 ` [RFC PATCH 5/6] spi: cadence-qspi: Tune PHY to allow running at higher frequencies Pratyush Yadav
2021-04-29 22:48   ` Michael Walle
2021-04-30  5:42     ` Pratyush Yadav
2021-03-11 19:12 ` [RFC PATCH 6/6] arm64: dts: ti: k3-j721e-som-p0: Enable PHY calibration Pratyush Yadav
2021-03-12  9:09 ` [RFC PATCH 0/6] spi: Add OSPI PHY calibration support for spi-cadence-quadspi Tudor.Ambarus
2021-03-12 10:10   ` Pratyush Yadav
2021-03-12 10:20     ` Michael Walle
2021-03-12 11:07       ` Pratyush Yadav
2021-03-12 13:26         ` Michael Walle
2021-03-12 11:23     ` Tudor.Ambarus
2021-03-12 18:14       ` Pratyush Yadav
2021-03-12 13:32 ` Michael Walle
2021-03-12 14:59   ` Tudor.Ambarus
2021-03-12 17:00   ` Pratyush Yadav

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=6dfbb3e4107887dc9ee3e19e4940e87c@walle.cc \
    --to=michael@walle.cc \
    --cc=broonie@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=kristo@kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mtd@lists.infradead.org \
    --cc=linux-spi@vger.kernel.org \
    --cc=lokeshvutla@ti.com \
    --cc=miquel.raynal@bootlin.com \
    --cc=nm@ti.com \
    --cc=p.yadav@ti.com \
    --cc=richard@nod.at \
    --cc=robh+dt@kernel.org \
    --cc=tudor.ambarus@microchip.com \
    --cc=vigneshr@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-SPI Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-spi/0 linux-spi/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-spi linux-spi/ https://lore.kernel.org/linux-spi \
		linux-spi@vger.kernel.org
	public-inbox-index linux-spi

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-spi


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git