* [PATCH] configs: OrangePi PC2: Update defaults
@ 2021-06-07 17:42 Jernej Skrabec
2021-06-12 5:50 ` Jernej Škrabec
0 siblings, 1 reply; 4+ messages in thread
From: Jernej Skrabec @ 2021-06-07 17:42 UTC (permalink / raw)
To: andre.przywara; +Cc: jagan, u-boot, linux-sunxi, Jernej Skrabec
OrangePi PC2 board has DRAM with ODT, so enable it. ZQ value is also
slightly different in vendor images, so update it as well. H5 SoC is
also connected to voltage regulator. It's default value is pretty low,
so in order to avoid instability, enable driver for it and set it to
appropriate voltage.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
---
configs/orangepi_pc2_defconfig | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
diff --git a/configs/orangepi_pc2_defconfig b/configs/orangepi_pc2_defconfig
index f72ffe27b26c..5e4cca793f53 100644
--- a/configs/orangepi_pc2_defconfig
+++ b/configs/orangepi_pc2_defconfig
@@ -3,13 +3,15 @@ CONFIG_ARCH_SUNXI=y
CONFIG_SPL=y
CONFIG_MACH_SUN50I_H5=y
CONFIG_DRAM_CLK=672
-CONFIG_DRAM_ZQ=3881977
-# CONFIG_DRAM_ODT_EN is not set
+CONFIG_DRAM_ZQ=4145117
CONFIG_MACPWR="PD6"
CONFIG_SPL_SPI_SUNXI=y
+CONFIG_SPL_I2C_SUPPORT=y
CONFIG_DEFAULT_DEVICE_TREE="sun50i-h5-orangepi-pc2"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SUN8I_EMAC=y
+CONFIG_SY8106A_POWER=y
+CONFIG_SY8106A_VOUT1_VOLT=1100
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_MUSB_GADGET=y
--
2.31.1
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH] configs: OrangePi PC2: Update defaults
2021-06-07 17:42 [PATCH] configs: OrangePi PC2: Update defaults Jernej Skrabec
@ 2021-06-12 5:50 ` Jernej Škrabec
2021-06-12 6:08 ` Jernej Škrabec
2021-06-13 23:25 ` Andre Przywara
0 siblings, 2 replies; 4+ messages in thread
From: Jernej Škrabec @ 2021-06-12 5:50 UTC (permalink / raw)
To: andre.przywara; +Cc: jagan, u-boot, linux-sunxi
Dne ponedeljek, 07. junij 2021 ob 19:42:45 CEST je Jernej Skrabec napisal(a):
> OrangePi PC2 board has DRAM with ODT, so enable it. ZQ value is also
> slightly different in vendor images, so update it as well. H5 SoC is
> also connected to voltage regulator. It's default value is pretty low,
> so in order to avoid instability, enable driver for it and set it to
> appropriate voltage.
>
> Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
> ---
> configs/orangepi_pc2_defconfig | 6 ++++--
> 1 file changed, 4 insertions(+), 2 deletions(-)
>
> diff --git a/configs/orangepi_pc2_defconfig b/configs/orangepi_pc2_defconfig
> index f72ffe27b26c..5e4cca793f53 100644
> --- a/configs/orangepi_pc2_defconfig
> +++ b/configs/orangepi_pc2_defconfig
> @@ -3,13 +3,15 @@ CONFIG_ARCH_SUNXI=y
> CONFIG_SPL=y
> CONFIG_MACH_SUN50I_H5=y
> CONFIG_DRAM_CLK=672
> -CONFIG_DRAM_ZQ=3881977
> -# CONFIG_DRAM_ODT_EN is not set
> +CONFIG_DRAM_ZQ=4145117
> CONFIG_MACPWR="PD6"
> CONFIG_SPL_SPI_SUNXI=y
> +CONFIG_SPL_I2C_SUPPORT=y
> CONFIG_DEFAULT_DEVICE_TREE="sun50i-h5-orangepi-pc2"
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_SUN8I_EMAC=y
> +CONFIG_SY8106A_POWER=y
> +CONFIG_SY8106A_VOUT1_VOLT=1100
I'm not sure if voltage regulator adjustment needs to be enabled. By default,
it's set to 1.1 V using resistor divider. However, it can be still needed if
board is rebooted and OS set it to lower value before reboot.
Best regards,
Jernej
> CONFIG_USB_EHCI_HCD=y
> CONFIG_USB_OHCI_HCD=y
> CONFIG_USB_MUSB_GADGET=y
> --
> 2.31.1
>
>
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Re: [PATCH] configs: OrangePi PC2: Update defaults
2021-06-12 5:50 ` Jernej Škrabec
@ 2021-06-12 6:08 ` Jernej Škrabec
2021-06-13 23:25 ` Andre Przywara
1 sibling, 0 replies; 4+ messages in thread
From: Jernej Škrabec @ 2021-06-12 6:08 UTC (permalink / raw)
To: andre.przywara; +Cc: jagan, u-boot, linux-sunxi
Dne sobota, 12. junij 2021 ob 07:50:27 CEST je Jernej Škrabec napisal(a):
> Dne ponedeljek, 07. junij 2021 ob 19:42:45 CEST je Jernej Skrabec
napisal(a):
> > OrangePi PC2 board has DRAM with ODT, so enable it. ZQ value is also
> > slightly different in vendor images, so update it as well. H5 SoC is
> > also connected to voltage regulator. It's default value is pretty low,
> > so in order to avoid instability, enable driver for it and set it to
> > appropriate voltage.
> >
> > Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
> > ---
> > configs/orangepi_pc2_defconfig | 6 ++++--
> > 1 file changed, 4 insertions(+), 2 deletions(-)
> >
> > diff --git a/configs/orangepi_pc2_defconfig b/configs/orangepi_pc2_defconfig
> > index f72ffe27b26c..5e4cca793f53 100644
> > --- a/configs/orangepi_pc2_defconfig
> > +++ b/configs/orangepi_pc2_defconfig
> > @@ -3,13 +3,15 @@ CONFIG_ARCH_SUNXI=y
> > CONFIG_SPL=y
> > CONFIG_MACH_SUN50I_H5=y
> > CONFIG_DRAM_CLK=672
> > -CONFIG_DRAM_ZQ=3881977
> > -# CONFIG_DRAM_ODT_EN is not set
> > +CONFIG_DRAM_ZQ=4145117
I re-checked BSP DT and original ZQ value is correct. So this patch should
only enable ODT, which is really enabled in BSP and DRAM ICs support it.
Best regards,
Jernej
> > CONFIG_MACPWR="PD6"
> > CONFIG_SPL_SPI_SUNXI=y
> > +CONFIG_SPL_I2C_SUPPORT=y
> > CONFIG_DEFAULT_DEVICE_TREE="sun50i-h5-orangepi-pc2"
> > # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> > CONFIG_SUN8I_EMAC=y
> > +CONFIG_SY8106A_POWER=y
> > +CONFIG_SY8106A_VOUT1_VOLT=1100
>
> I'm not sure if voltage regulator adjustment needs to be enabled. By
default,
> it's set to 1.1 V using resistor divider. However, it can be still needed if
> board is rebooted and OS set it to lower value before reboot.
>
> Best regards,
> Jernej
>
> > CONFIG_USB_EHCI_HCD=y
> > CONFIG_USB_OHCI_HCD=y
> > CONFIG_USB_MUSB_GADGET=y
> > --
> > 2.31.1
> >
> >
>
>
>
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH] configs: OrangePi PC2: Update defaults
2021-06-12 5:50 ` Jernej Škrabec
2021-06-12 6:08 ` Jernej Škrabec
@ 2021-06-13 23:25 ` Andre Przywara
1 sibling, 0 replies; 4+ messages in thread
From: Andre Przywara @ 2021-06-13 23:25 UTC (permalink / raw)
To: Jernej Škrabec; +Cc: jagan, u-boot, linux-sunxi
On Sat, 12 Jun 2021 07:50:27 +0200
Jernej Škrabec <jernej.skrabec@gmail.com> wrote:
Hi,
> Dne ponedeljek, 07. junij 2021 ob 19:42:45 CEST je Jernej Skrabec napisal(a):
> > OrangePi PC2 board has DRAM with ODT, so enable it. ZQ value is also
> > slightly different in vendor images, so update it as well. H5 SoC is
> > also connected to voltage regulator. It's default value is pretty low,
> > so in order to avoid instability, enable driver for it and set it to
> > appropriate voltage.
> >
> > Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
> > ---
> > configs/orangepi_pc2_defconfig | 6 ++++--
> > 1 file changed, 4 insertions(+), 2 deletions(-)
> >
> > diff --git a/configs/orangepi_pc2_defconfig b/configs/orangepi_pc2_defconfig
> > index f72ffe27b26c..5e4cca793f53 100644
> > --- a/configs/orangepi_pc2_defconfig
> > +++ b/configs/orangepi_pc2_defconfig
> > @@ -3,13 +3,15 @@ CONFIG_ARCH_SUNXI=y
> > CONFIG_SPL=y
> > CONFIG_MACH_SUN50I_H5=y
> > CONFIG_DRAM_CLK=672
> > -CONFIG_DRAM_ZQ=3881977
> > -# CONFIG_DRAM_ODT_EN is not set
> > +CONFIG_DRAM_ZQ=4145117
> > CONFIG_MACPWR="PD6"
> > CONFIG_SPL_SPI_SUNXI=y
> > +CONFIG_SPL_I2C_SUPPORT=y
> > CONFIG_DEFAULT_DEVICE_TREE="sun50i-h5-orangepi-pc2"
> > # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> > CONFIG_SUN8I_EMAC=y
> > +CONFIG_SY8106A_POWER=y
> > +CONFIG_SY8106A_VOUT1_VOLT=1100
>
> I'm not sure if voltage regulator adjustment needs to be enabled. By default,
> it's set to 1.1 V using resistor divider. However, it can be still needed if
> board is rebooted and OS set it to lower value before reboot.
Yeah, I had a similar train of thoughts: originally I though we don't
need it, because of the resistor divider providing a good default
voltage. But indeed if we reset from a lower p-state (either by chance
or because of say the powersave governor being active), I really see the
lowest voltage (1.0V) being still set in when back in U-Boot, which
could lead to instabilities if the CPU runs at the 816 MHz we set the
PLL to.
So enabling the regulator sounds indicated, as we set the CPU frequency
as well. This is especially critical when the OS doesn't use DVFS.
Because of this I am inclined to take the regulator part now.
For the ODT change, I will queue this for the next release.
Thanks,
Andre.
>
> Best regards,
> Jernej
>
> > CONFIG_USB_EHCI_HCD=y
> > CONFIG_USB_OHCI_HCD=y
> > CONFIG_USB_MUSB_GADGET=y
> > --
> > 2.31.1
> >
> >
>
>
>
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2021-06-13 23:25 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-06-07 17:42 [PATCH] configs: OrangePi PC2: Update defaults Jernej Skrabec
2021-06-12 5:50 ` Jernej Škrabec
2021-06-12 6:08 ` Jernej Škrabec
2021-06-13 23:25 ` Andre Przywara
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).