[PATCH 0/2] arm64: dts: allwinner: Add BananaPi M4 Berry

[PATCH 0/2] arm64: dts: allwinner: Add BananaPi M4 Berry

[Andre Przywara]

The BananaPi M4 Berry is a development board with the Allwinner H618
SoC. It comes with 2GB DRAM and 8GB eMMC flash, with the usual suspects
like HDMI, SD card, GPIO headers. There are four USB ports connected
via an on-board hub chip, and a Gigabit Ethernet socket. Also there is
a USB WiFi chip soldered on the board.
More details: https://linux-sunxi.org/Sinovoip_Banana_Pi_M4_Berry

I don't have this board, so this is a "call for testing".
One thing to consider:
- The USB WiFi chip has a CHIP_EN pin, which can turn the chip off.
  It is pulled up by a resistor, so works out of the box, but is also
  connected to a GPIO (PC2), so the chip can be disabled or reset via
  this pin. Since this is a USB device, we don't have a DT node to
  announce this pin. Any ideas how this should be handled? At the moment
  I ignore it, but it could also be modelled as a USB VBUS regulator for
  USB port 1, to which it is connected.

When testing this, please have a look at:
- Does the eMMC work in HS200 mode? The vendor DT described that as a
  3.3V controlled eMMC only, but clearly the schematic uses 1.8V, which
  allows faster transfer modes. "hdparm -t" should suffice for a quick
  test.
- Do USB full-speed (aka USB v1.1) peripherals like keyboard or mouse
  work on the USB ports? I disabled the OHCI node, since the hub should
  not need this, but it would be good to double check.
- Similarly the USB WiFi chip probably doesn't need USB 1.1 modes, so
  please check this still works.

Apart from the missing audio and video support (which are due to missing
bindings for the H616/H618 SoC), most of the peripherals are supported.

Patch 1/2 adds the board compatible string to the bindings, patch 2/2
adds the actual .dts file.

Please have a look!

Thanks,
Andre

Andre Przywara (2):
  dt-bindings: arm: sunxi: document BananaPi M4 Berry board name
  arm64: dts: allwinner: h618: add BananaPi M4 Berry board

 .../devicetree/bindings/arm/sunxi.yaml        |   5 +
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../sun50i-h618-bananapi-m4-berry.dts         | 229 ++++++++++++++++++
 3 files changed, 235 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts

-- 
2.35.8

[PATCH 1/2] dt-bindings: arm: sunxi: document BananaPi M4 Berry board name

[Andre Przywara]

The Bananapi M4 Berry is a development board with the Allwinner H618 SoC.

Add the board/SoC compatible string pair to the list of known boards.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml
index 5e91110cc9eb8..b659e03550315 100644
--- a/Documentation/devicetree/bindings/arm/sunxi.yaml
+++ b/Documentation/devicetree/bindings/arm/sunxi.yaml
@@ -136,6 +136,11 @@ properties:
           - const: sinovoip,bpi-m3
           - const: allwinner,sun8i-a83t
 
+      - description: BananaPi M4 Berry
+        items:
+          - const: sinovoip,bananapi-m4-berry
+          - const: allwinner,sun50i-h618
+
       - description: BananaPi M64
         items:
           - const: sinovoip,bananapi-m64
-- 
2.35.8

Re: [PATCH 1/2] dt-bindings: arm: sunxi: document BananaPi M4 Berry board name

[Krzysztof Kozlowski]

On 18/12/2023 00:24, Andre Przywara wrote:
> The Bananapi M4 Berry is a development board with the Allwinner H618 SoC.
> 
> Add the board/SoC compatible string pair to the list of known boards.
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
>  Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++
>  1 file changed, 5 insertions(+)
> 

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

[PATCH 2/2] arm64: dts: allwinner: h618: add BananaPi M4 Berry board

[Andre Przywara]

The BananaPi M4 Berry is a development board using the Allwinner H618
SoC. It comes with the following specs:
	- Allwinner H618 SoC (4 * Arm Cortex-A53 cores, 1MB L2 cache)
	- 2 GiB LPDDR4 DRAM
	- 8 GiB eMMC flash
	- AXP313a PMIC
	- Gigabit Ethernet, using RTL8211 PHY
	- RTL8821CU USB WiFi chip
	- HDMI port
	- 4 * USB 2.0 ports, via an on-board hub chip
	- microSD card slot
	- 3.5mm A/V port
	- power supply and USB-OTG via USB-C connector

Add a devicetree file describing the components that we already have
bindings for, that excludes audio and video at the moment.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../sun50i-h618-bananapi-m4-berry.dts         | 229 ++++++++++++++++++
 2 files changed, 230 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 91d505b385de5..ed016688bb56f 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -42,5 +42,6 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-bigtreetech-cb1-manta.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-bigtreetech-pi.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-bananapi-m4-berry.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero3.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-transpeed-8k618-t.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts b/arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts
new file mode 100644
index 0000000000000..11d893a767d4e
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts
@@ -0,0 +1,229 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2023 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "BananaPi M4 Berry";
+	compatible = "sinovoip,bananapi-m4-berry", "allwinner,sun50i-h618";
+
+	aliases {
+		ethernet0 = &emac0;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pio 2 12 GPIO_ACTIVE_LOW>; /* PC12 */
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-sw4 {
+			label = "sw3";
+			linux,code = <BTN_0>;
+			gpios = <&pio 2 7 GPIO_ACTIVE_LOW>;	/* PC7 */
+		};
+	};
+
+	reg_vcc5v: vcc5v {
+		/* board wide 5V supply directly from the USB-C socket */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	reg_usb_vbus: regulator-usb-vbus {
+		/* separate discrete regulator for the USB ports */
+		compatible = "regulator-fixed";
+		regulator-name = "usb-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_vcc5v>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		/* separate discrete regulator for WiFi and Ethernet PHY */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_vcc5v>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+/* Connected to an on-board RTL8821CU USB WiFi chip. */
+&ehci1 {
+	status = "okay";
+};
+
+/* on unpopulated pins */
+&ehci2 {
+	status = "disabled";
+};
+
+/* Connected to an on-board FE1.1s USB hub chip, supplying 4 USB-A ports. */
+&ehci3 {
+	status = "okay";
+};
+
+&emac0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ext_rgmii_pins>;
+	phy-mode = "rgmii";
+	phy-handle = <&ext_rgmii_phy>;
+	phy-supply = <&reg_3v3>;
+	allwinner,rx-delay-ps = <3100>;
+	allwinner,tx-delay-ps = <700>;
+	status = "okay";
+};
+
+&ir {
+	status = "okay";
+};
+
+&mdio0 {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+		reset-gpios = <&pio 8 16 GPIO_ACTIVE_LOW>;	/* PI16 */
+	};
+};
+
+&mmc0 {
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;	/* PF6 */
+	vmmc-supply = <&reg_dldo1>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc2 {
+	vmmc-supply = <&reg_dldo1>;
+	vqmmc-supply = <&reg_aldo1>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	status = "okay";
+};
+
+/* USB ports 1 and 3 connect to onboard devices that are high-speed only. */
+
+/* on unpopulated pins */
+&ohci2 {
+	status = "disabled";
+};
+
+&pio {
+	vcc-pc-supply = <&reg_aldo1>;
+	vcc-pf-supply = <&reg_dldo1>;
+	vcc-pg-supply = <&reg_dldo1>;
+	vcc-ph-supply = <&reg_dldo1>;
+	vcc-pi-supply = <&reg_dldo1>;
+};
+
+&r_i2c {
+	status = "okay";
+
+	axp313: pmic@36 {
+		compatible = "x-powers,axp313a";
+		reg = <0x36>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		interrupt-parent = <&pio>;
+
+		vin1-supply = <&reg_vcc5v>;
+		vin2-supply = <&reg_vcc5v>;
+		vin3-supply = <&reg_vcc5v>;
+
+		regulators {
+			reg_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc-1v8-pll";
+			};
+
+			reg_dldo1: dldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-3v3-io";
+			};
+
+			reg_dcdc1: dcdc1 {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <990000>;
+				regulator-name = "vdd-gpu-sys";
+			};
+
+			reg_dcdc2: dcdc2 {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-cpu";
+			};
+
+			reg_dcdc3: dcdc3 {
+				regulator-always-on;
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-dram";
+			};
+		};
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ph_pins>;
+	status = "okay";
+};
+
+&usbotg {
+	/*
+	 * PHY0 pins are connected to a USB-C socket, but a role switch is not
+	 * implemented: both CC pins are pulled to GND via a 5.1K resistor.
+	 * The VBUS pins power the device, so a fixed peripheral mode
+	 * is the best choice.
+	 * The board can be powered via GPIOs, in this case port0 *can*
+	 * act as a host (with a cable/adapter ignoring CC), as VBUS is
+	 * then provided by the GPIOs. Any user of this setup would
+	 * need to adjust the DT accordingly: dr_mode set to "host",
+	 * enabling OHCI0 and EHCI0.
+	 */
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	usb3_vbus-supply = <&reg_usb_vbus>;
+	status = "okay";
+};
-- 
2.35.8

Re: [PATCH 2/2] arm64: dts: allwinner: h618: add BananaPi M4 Berry board

[Krzysztof Kozlowski]

On 18/12/2023 00:24, Andre Przywara wrote:
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +
> +		key-sw4 {
> +			label = "sw3";
> +			linux,code = <BTN_0>;
> +			gpios = <&pio 2 7 GPIO_ACTIVE_LOW>;	/* PC7 */
> +		};
> +	};
> +
> +	reg_vcc5v: vcc5v {

regulator prefix to the node name (others have it).

> +		/* board wide 5V supply directly from the USB-C socket */
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc-5v";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +	};
> +
> +	reg_usb_vbus: regulator-usb-vbus {
> +		/* separate discrete regulator for the USB ports */
> +		compatible = "regulator-fixed";
> +		regulator-name = "usb-vbus";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&reg_vcc5v>;
> +	};
> +
> +	reg_3v3: regulator-3v3 {
> +		/* separate discrete regulator for WiFi and Ethernet PHY */
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc-3v3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&reg_vcc5v>;
> +	};
> +};
> +

Best regards,
Krzysztof

Re: [PATCH 2/2] arm64: dts: allwinner: h618: add BananaPi M4 Berry board

[Jernej Škrabec]

Hi Andre!

Dne ponedeljek, 18. december 2023 ob 00:24:05 CET je Andre Przywara napisal(a):
> The BananaPi M4 Berry is a development board using the Allwinner H618
> SoC. It comes with the following specs:
> 	- Allwinner H618 SoC (4 * Arm Cortex-A53 cores, 1MB L2 cache)
> 	- 2 GiB LPDDR4 DRAM
> 	- 8 GiB eMMC flash
> 	- AXP313a PMIC
> 	- Gigabit Ethernet, using RTL8211 PHY
> 	- RTL8821CU USB WiFi chip
> 	- HDMI port
> 	- 4 * USB 2.0 ports, via an on-board hub chip
> 	- microSD card slot
> 	- 3.5mm A/V port
> 	- power supply and USB-OTG via USB-C connector
> 
> Add a devicetree file describing the components that we already have
> bindings for, that excludes audio and video at the moment.
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
>  arch/arm64/boot/dts/allwinner/Makefile        |   1 +
>  .../sun50i-h618-bananapi-m4-berry.dts         | 229 ++++++++++++++++++
>  2 files changed, 230 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts
> 
> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> index 91d505b385de5..ed016688bb56f 100644
> --- a/arch/arm64/boot/dts/allwinner/Makefile
> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> @@ -42,5 +42,6 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-bigtreetech-cb1-manta.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-bigtreetech-pi.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-bananapi-m4-berry.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero3.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-transpeed-8k618-t.dtb
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts b/arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts
> new file mode 100644
> index 0000000000000..11d893a767d4e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts
> @@ -0,0 +1,229 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (C) 2023 Arm Ltd.
> + */
> +
> +/dts-v1/;
> +
> +#include "sun50i-h616.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/leds/common.h>
> +
> +/ {
> +	model = "BananaPi M4 Berry";
> +	compatible = "sinovoip,bananapi-m4-berry", "allwinner,sun50i-h618";
> +
> +	aliases {
> +		ethernet0 = &emac0;
> +		serial0 = &uart0;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		led-0 {
> +			function = LED_FUNCTION_STATUS;
> +			color = <LED_COLOR_ID_GREEN>;
> +			gpios = <&pio 2 12 GPIO_ACTIVE_LOW>; /* PC12 */
> +		};
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +
> +		key-sw4 {

"key-sw3"

> +			label = "sw3";
> +			linux,code = <BTN_0>;
> +			gpios = <&pio 2 7 GPIO_ACTIVE_LOW>;	/* PC7 */
> +		};
> +	};
> +
> +	reg_vcc5v: vcc5v {
> +		/* board wide 5V supply directly from the USB-C socket */
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc-5v";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +	};
> +
> +	reg_usb_vbus: regulator-usb-vbus {
> +		/* separate discrete regulator for the USB ports */
> +		compatible = "regulator-fixed";
> +		regulator-name = "usb-vbus";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&reg_vcc5v>;
> +	};
> +
> +	reg_3v3: regulator-3v3 {
> +		/* separate discrete regulator for WiFi and Ethernet PHY */
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc-3v3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&reg_vcc5v>;
> +	};
> +};
> +
> +&cpu0 {
> +	cpu-supply = <&reg_dcdc2>;
> +};
> +
> +/* Connected to an on-board RTL8821CU USB WiFi chip. */
> +&ehci1 {
> +	status = "okay";
> +};
> +
> +/* on unpopulated pins */
> +&ehci2 {
> +	status = "disabled";
> +};

Just drop above node. I get that it's for documenting purposes, but user need
to use DT overlay in any case.

> +
> +/* Connected to an on-board FE1.1s USB hub chip, supplying 4 USB-A ports. */
> +&ehci3 {
> +	status = "okay";
> +};
> +
> +&emac0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&ext_rgmii_pins>;
> +	phy-mode = "rgmii";
> +	phy-handle = <&ext_rgmii_phy>;
> +	phy-supply = <&reg_3v3>;
> +	allwinner,rx-delay-ps = <3100>;
> +	allwinner,tx-delay-ps = <700>;
> +	status = "okay";
> +};
> +
> +&ir {
> +	status = "okay";
> +};
> +
> +&mdio0 {
> +	ext_rgmii_phy: ethernet-phy@1 {
> +		compatible = "ethernet-phy-ieee802.3-c22";
> +		reg = <1>;
> +		reset-gpios = <&pio 8 16 GPIO_ACTIVE_LOW>;	/* PI16 */
> +	};
> +};
> +
> +&mmc0 {
> +	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;	/* PF6 */
> +	vmmc-supply = <&reg_dldo1>;
> +	bus-width = <4>;
> +	status = "okay";
> +};
> +
> +&mmc2 {
> +	vmmc-supply = <&reg_dldo1>;
> +	vqmmc-supply = <&reg_aldo1>;
> +	bus-width = <8>;
> +	non-removable;
> +	cap-mmc-hw-reset;
> +	mmc-ddr-1_8v;
> +	mmc-hs200-1_8v;
> +	status = "okay";
> +};
> +
> +/* USB ports 1 and 3 connect to onboard devices that are high-speed only. */
> +
> +/* on unpopulated pins */
> +&ohci2 {
> +	status = "disabled";
> +};

Ditto.

Best regards,
Jernej

> +
> +&pio {
> +	vcc-pc-supply = <&reg_aldo1>;
> +	vcc-pf-supply = <&reg_dldo1>;
> +	vcc-pg-supply = <&reg_dldo1>;
> +	vcc-ph-supply = <&reg_dldo1>;
> +	vcc-pi-supply = <&reg_dldo1>;
> +};
> +
> +&r_i2c {
> +	status = "okay";
> +
> +	axp313: pmic@36 {
> +		compatible = "x-powers,axp313a";
> +		reg = <0x36>;
> +		#interrupt-cells = <1>;
> +		interrupt-controller;
> +		interrupt-parent = <&pio>;
> +
> +		vin1-supply = <&reg_vcc5v>;
> +		vin2-supply = <&reg_vcc5v>;
> +		vin3-supply = <&reg_vcc5v>;
> +
> +		regulators {
> +			reg_aldo1: aldo1 {
> +				regulator-always-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-name = "vcc-1v8-pll";
> +			};
> +
> +			reg_dldo1: dldo1 {
> +				regulator-always-on;
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-name = "vcc-3v3-io";
> +			};
> +
> +			reg_dcdc1: dcdc1 {
> +				regulator-always-on;
> +				regulator-min-microvolt = <810000>;
> +				regulator-max-microvolt = <990000>;
> +				regulator-name = "vdd-gpu-sys";
> +			};
> +
> +			reg_dcdc2: dcdc2 {
> +				regulator-always-on;
> +				regulator-min-microvolt = <810000>;
> +				regulator-max-microvolt = <1100000>;
> +				regulator-name = "vdd-cpu";
> +			};
> +
> +			reg_dcdc3: dcdc3 {
> +				regulator-always-on;
> +				regulator-min-microvolt = <1100000>;
> +				regulator-max-microvolt = <1100000>;
> +				regulator-name = "vdd-dram";
> +			};
> +		};
> +	};
> +};
> +
> +&uart0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart0_ph_pins>;
> +	status = "okay";
> +};
> +
> +&usbotg {
> +	/*
> +	 * PHY0 pins are connected to a USB-C socket, but a role switch is not
> +	 * implemented: both CC pins are pulled to GND via a 5.1K resistor.
> +	 * The VBUS pins power the device, so a fixed peripheral mode
> +	 * is the best choice.
> +	 * The board can be powered via GPIOs, in this case port0 *can*
> +	 * act as a host (with a cable/adapter ignoring CC), as VBUS is
> +	 * then provided by the GPIOs. Any user of this setup would
> +	 * need to adjust the DT accordingly: dr_mode set to "host",
> +	 * enabling OHCI0 and EHCI0.
> +	 */
> +	dr_mode = "peripheral";
> +	status = "okay";
> +};
> +
> +&usbphy {
> +	usb3_vbus-supply = <&reg_usb_vbus>;
> +	status = "okay";
> +};
> 

Re: [PATCH 0/2] arm64: dts: allwinner: Add BananaPi M4 Berry

[Chen-Yu Tsai]

On Mon, Dec 18, 2023 at 7:24 AM Andre Przywara <andre.przywara@arm.com> wrote:
>
> The BananaPi M4 Berry is a development board with the Allwinner H618
> SoC. It comes with 2GB DRAM and 8GB eMMC flash, with the usual suspects
> like HDMI, SD card, GPIO headers. There are four USB ports connected
> via an on-board hub chip, and a Gigabit Ethernet socket. Also there is
> a USB WiFi chip soldered on the board.
> More details: https://linux-sunxi.org/Sinovoip_Banana_Pi_M4_Berry
>
> I don't have this board, so this is a "call for testing".
> One thing to consider:
> - The USB WiFi chip has a CHIP_EN pin, which can turn the chip off.
>   It is pulled up by a resistor, so works out of the box, but is also
>   connected to a GPIO (PC2), so the chip can be disabled or reset via
>   this pin. Since this is a USB device, we don't have a DT node to
>   announce this pin. Any ideas how this should be handled? At the moment
>   I ignore it, but it could also be modelled as a USB VBUS regulator for
>   USB port 1, to which it is connected.

There was a talk on this topic at Plumbers:

https://lpc.events/event/17/contributions/1507/

So I'd say a proper solution is being worked on.

ChenYu

> When testing this, please have a look at:
> - Does the eMMC work in HS200 mode? The vendor DT described that as a
>   3.3V controlled eMMC only, but clearly the schematic uses 1.8V, which
>   allows faster transfer modes. "hdparm -t" should suffice for a quick
>   test.
> - Do USB full-speed (aka USB v1.1) peripherals like keyboard or mouse
>   work on the USB ports? I disabled the OHCI node, since the hub should
>   not need this, but it would be good to double check.
> - Similarly the USB WiFi chip probably doesn't need USB 1.1 modes, so
>   please check this still works.
>
> Apart from the missing audio and video support (which are due to missing
> bindings for the H616/H618 SoC), most of the peripherals are supported.
>
> Patch 1/2 adds the board compatible string to the bindings, patch 2/2
> adds the actual .dts file.
>
> Please have a look!
>
> Thanks,
> Andre
>
> Andre Przywara (2):
>   dt-bindings: arm: sunxi: document BananaPi M4 Berry board name
>   arm64: dts: allwinner: h618: add BananaPi M4 Berry board
>
>  .../devicetree/bindings/arm/sunxi.yaml        |   5 +
>  arch/arm64/boot/dts/allwinner/Makefile        |   1 +
>  .../sun50i-h618-bananapi-m4-berry.dts         | 229 ++++++++++++++++++
>  3 files changed, 235 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h618-bananapi-m4-berry.dts
>
> --
> 2.35.8
>