* [PATCH v9 1/6] dt_bindings: mfd: Add ROHM BD9576MUF and BD9573MUF PMICs
2021-03-10 8:02 [PATCH v9 0/6] Support ROHM BD9576MUF and BD9573MUF PMICs Matti Vaittinen
@ 2021-03-10 8:05 ` Matti Vaittinen
2021-03-10 8:06 ` [PATCH v9 2/6] mfd: Support ROHM BD9576MUF and BD9573MUF Matti Vaittinen
` (5 subsequent siblings)
6 siblings, 0 replies; 8+ messages in thread
From: Matti Vaittinen @ 2021-03-10 8:05 UTC (permalink / raw)
To: matti.vaittinen, mazziesaccount
Cc: Lee Jones, Rob Herring, Matti Vaittinen, Wim Van Sebroeck,
Guenter Roeck, devicetree, linux-kernel, linux-power,
linux-watchdog
Add bindings for ROHM BD9576MUF and BD9573MUF PMICs. These
PMICs are primarily intended to be used to power the R-Car series
processors. They provide 6 power outputs, safety features and a
watchdog with two functional modes.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
No changes from v8
.../bindings/mfd/rohm,bd9576-pmic.yaml | 123 ++++++++++++++++++
1 file changed, 123 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd9576-pmic.yaml
diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd9576-pmic.yaml b/Documentation/devicetree/bindings/mfd/rohm,bd9576-pmic.yaml
new file mode 100644
index 000000000000..6483860da955
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/rohm,bd9576-pmic.yaml
@@ -0,0 +1,123 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/rohm,bd9576-pmic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ROHM BD9576MUF and BD9573MUF Power Management Integrated Circuit bindings
+
+maintainers:
+ - Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
+
+description: |
+ BD9576MUF and BD9573MUF are power management ICs primarily intended for
+ powering the R-Car series processors.
+ The IC provides 6 power outputs with configurable sequencing and safety
+ monitoring. A watchdog logic with slow ping/windowed modes is also included.
+
+properties:
+ compatible:
+ enum:
+ - rohm,bd9576
+ - rohm,bd9573
+
+ reg:
+ description:
+ I2C slave address.
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ rohm,vout1-en-low:
+ description:
+ BD9576 and BD9573 VOUT1 regulator enable state can be individually
+ controlled by a GPIO. This is dictated by state of vout1-en pin during
+ the PMIC startup. If vout1-en is LOW during PMIC startup then the VOUT1
+ enable sate is controlled via this pin. Set this property if vout1-en
+ is wired to be down at PMIC start-up.
+ type: boolean
+
+ rohm,vout1-en-gpios:
+ description:
+ GPIO specifier to specify the GPIO connected to vout1-en for vout1 ON/OFF
+ state control.
+ maxItems: 1
+
+ rohm,ddr-sel-low:
+ description:
+ The BD9576 and BD9573 output voltage for DDR can be selected by setting
+ the ddr-sel pin low or high. Set this property if ddr-sel is grounded.
+ type: boolean
+
+ rohm,watchdog-enable-gpios:
+ description: The GPIO line used to enable the watchdog.
+ maxItems: 1
+
+ rohm,watchdog-ping-gpios:
+ description: The GPIO line used to ping the watchdog.
+ maxItems: 1
+
+ rohm,hw-timeout-ms:
+ maxItems: 2
+ description:
+ Watchog timeout in milliseconds. If single value is given it is
+ the maximum timeout. Eg. if pinging watchdog is not done within this time
+ limit the watchdog will be triggered. If two values are given watchdog
+ is configured in "window mode". Then first value is limit for short-ping
+ Eg. if watchdog is pinged sooner than that the watchdog will trigger.
+ When two values is given the second value is the maximum timeout.
+ # (HW) minimum for short timeout is 2ms, maximum 220 ms.
+ # (HW) minimum for max timeout is 4ms, maximum 4416 ms.
+
+ regulators:
+ $ref: ../regulator/rohm,bd9576-regulator.yaml
+ description:
+ List of child nodes that specify the regulators.
+
+required:
+ - compatible
+ - reg
+ - regulators
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/leds/common.h>
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pmic: pmic@30 {
+ compatible = "rohm,bd9576";
+ reg = <0x30>;
+ rohm,vout1-en-low;
+ rohm,vout1-en-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>;
+ rohm,ddr-sel-low;
+ rohm,watchdog-enable-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>;
+ rohm,watchdog-ping-gpios = <&gpio2 7 GPIO_ACTIVE_HIGH>;
+ rohm,hw-timeout-ms = <150>, <2300>;
+
+ regulators {
+ boost1: regulator-vd50 {
+ regulator-name = "VD50";
+ };
+ buck1: regulator-vd18 {
+ regulator-name = "VD18";
+ };
+ buck2: regulator-vdddr {
+ regulator-name = "VDDDR";
+ };
+ buck3: regulator-vd10 {
+ regulator-name = "VD10";
+ };
+ ldo: regulator-voutl1 {
+ regulator-name = "VOUTL1";
+ };
+ sw: regulator-vouts1 {
+ regulator-name = "VOUTS1";
+ };
+ };
+ };
+ };
--
2.25.4
--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND
~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH v9 2/6] mfd: Support ROHM BD9576MUF and BD9573MUF
2021-03-10 8:02 [PATCH v9 0/6] Support ROHM BD9576MUF and BD9573MUF PMICs Matti Vaittinen
2021-03-10 8:05 ` [PATCH v9 1/6] dt_bindings: mfd: Add " Matti Vaittinen
@ 2021-03-10 8:06 ` Matti Vaittinen
2021-03-10 8:08 ` [PATCH v9 3/6] mfd: bd9576: Add IRQ support Matti Vaittinen
` (4 subsequent siblings)
6 siblings, 0 replies; 8+ messages in thread
From: Matti Vaittinen @ 2021-03-10 8:06 UTC (permalink / raw)
To: matti.vaittinen, mazziesaccount
Cc: Lee Jones, Rob Herring, Matti Vaittinen, Wim Van Sebroeck,
Guenter Roeck, devicetree, linux-kernel, linux-power,
linux-watchdog
Add core support for ROHM BD9576MUF and BD9573MUF PMICs which are
mainly used to power the R-Car series processors.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
---
Changes from v8:
- updated copyright
drivers/mfd/Kconfig | 11 ++++
drivers/mfd/Makefile | 1 +
drivers/mfd/rohm-bd9576.c | 109 +++++++++++++++++++++++++++++++
include/linux/mfd/rohm-bd957x.h | 59 +++++++++++++++++
include/linux/mfd/rohm-generic.h | 2 +
5 files changed, 182 insertions(+)
create mode 100644 drivers/mfd/rohm-bd9576.c
create mode 100644 include/linux/mfd/rohm-bd957x.h
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index b74efa469e90..f0c9529e7bfd 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1989,6 +1989,17 @@ config MFD_ROHM_BD71828
Also included is a Coulomb counter, a real-time clock (RTC), and
a 32.768 kHz clock gate.
+config MFD_ROHM_BD957XMUF
+ tristate "ROHM BD9576MUF and BD9573MUF Power Management ICs"
+ depends on I2C=y
+ depends on OF
+ select REGMAP_I2C
+ select MFD_CORE
+ help
+ Select this option to get support for the ROHM BD9576MUF and
+ BD9573MUF Power Management ICs. BD9576 and BD9573 are primarily
+ designed to be used to power R-Car series processors.
+
config MFD_STM32_LPTIMER
tristate "Support for STM32 Low-Power Timer"
depends on (ARCH_STM32 && OF) || COMPILE_TEST
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 834f5463af28..d93f6f361fd3 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -261,6 +261,7 @@ obj-$(CONFIG_RAVE_SP_CORE) += rave-sp.o
obj-$(CONFIG_MFD_ROHM_BD70528) += rohm-bd70528.o
obj-$(CONFIG_MFD_ROHM_BD71828) += rohm-bd71828.o
obj-$(CONFIG_MFD_ROHM_BD718XX) += rohm-bd718x7.o
+obj-$(CONFIG_MFD_ROHM_BD957XMUF) += rohm-bd9576.o
obj-$(CONFIG_MFD_STMFX) += stmfx.o
obj-$(CONFIG_MFD_KHADAS_MCU) += khadas-mcu.o
obj-$(CONFIG_MFD_ACER_A500_EC) += acer-ec-a500.o
diff --git a/drivers/mfd/rohm-bd9576.c b/drivers/mfd/rohm-bd9576.c
new file mode 100644
index 000000000000..2dbda1f401e2
--- /dev/null
+++ b/drivers/mfd/rohm-bd9576.c
@@ -0,0 +1,109 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2021 ROHM Semiconductors
+ *
+ * ROHM BD9576MUF and BD9573MUF PMIC driver
+ */
+
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/irq.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/rohm-bd957x.h>
+#include <linux/mfd/rohm-generic.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+#include <linux/types.h>
+
+static struct mfd_cell bd9573_mfd_cells[] = {
+ { .name = "bd9573-regulator", },
+ { .name = "bd9576-wdt", },
+};
+
+static struct mfd_cell bd9576_mfd_cells[] = {
+ { .name = "bd9576-regulator", },
+ { .name = "bd9576-wdt", },
+};
+
+static const struct regmap_range volatile_ranges[] = {
+ regmap_reg_range(BD957X_REG_SMRB_ASSERT, BD957X_REG_SMRB_ASSERT),
+ regmap_reg_range(BD957X_REG_PMIC_INTERNAL_STAT,
+ BD957X_REG_PMIC_INTERNAL_STAT),
+ regmap_reg_range(BD957X_REG_INT_THERM_STAT, BD957X_REG_INT_THERM_STAT),
+ regmap_reg_range(BD957X_REG_INT_OVP_STAT, BD957X_REG_INT_SYS_STAT),
+ regmap_reg_range(BD957X_REG_INT_MAIN_STAT, BD957X_REG_INT_MAIN_STAT),
+};
+
+static const struct regmap_access_table volatile_regs = {
+ .yes_ranges = &volatile_ranges[0],
+ .n_yes_ranges = ARRAY_SIZE(volatile_ranges),
+};
+
+static struct regmap_config bd957x_regmap = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .volatile_table = &volatile_regs,
+ .max_register = BD957X_MAX_REGISTER,
+ .cache_type = REGCACHE_RBTREE,
+};
+
+static int bd957x_i2c_probe(struct i2c_client *i2c,
+ const struct i2c_device_id *id)
+{
+ int ret;
+ struct regmap *regmap;
+ struct mfd_cell *cells;
+ int num_cells;
+ unsigned long chip_type;
+
+ chip_type = (unsigned long)of_device_get_match_data(&i2c->dev);
+
+ switch (chip_type) {
+ case ROHM_CHIP_TYPE_BD9576:
+ cells = bd9576_mfd_cells;
+ num_cells = ARRAY_SIZE(bd9576_mfd_cells);
+ break;
+ case ROHM_CHIP_TYPE_BD9573:
+ cells = bd9573_mfd_cells;
+ num_cells = ARRAY_SIZE(bd9573_mfd_cells);
+ break;
+ default:
+ dev_err(&i2c->dev, "Unknown device type");
+ return -EINVAL;
+ }
+
+ regmap = devm_regmap_init_i2c(i2c, &bd957x_regmap);
+ if (IS_ERR(regmap)) {
+ dev_err(&i2c->dev, "Failed to initialize Regmap\n");
+ return PTR_ERR(regmap);
+ }
+
+ ret = devm_mfd_add_devices(&i2c->dev, PLATFORM_DEVID_AUTO, cells,
+ num_cells, NULL, 0, NULL);
+ if (ret)
+ dev_err(&i2c->dev, "Failed to create subdevices\n");
+
+ return ret;
+}
+
+static const struct of_device_id bd957x_of_match[] = {
+ { .compatible = "rohm,bd9576", .data = (void *)ROHM_CHIP_TYPE_BD9576, },
+ { .compatible = "rohm,bd9573", .data = (void *)ROHM_CHIP_TYPE_BD9573, },
+ { },
+};
+MODULE_DEVICE_TABLE(of, bd957x_of_match);
+
+static struct i2c_driver bd957x_drv = {
+ .driver = {
+ .name = "rohm-bd957x",
+ .of_match_table = bd957x_of_match,
+ },
+ .probe = &bd957x_i2c_probe,
+};
+module_i2c_driver(bd957x_drv);
+
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("ROHM BD9576MUF and BD9573MUF Power Management IC driver");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/mfd/rohm-bd957x.h b/include/linux/mfd/rohm-bd957x.h
new file mode 100644
index 000000000000..a631abb2c101
--- /dev/null
+++ b/include/linux/mfd/rohm-bd957x.h
@@ -0,0 +1,59 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/* Copyright (C) 2021 ROHM Semiconductors */
+
+#ifndef __LINUX_MFD_BD957X_H__
+#define __LINUX_MFD_BD957X_H__
+
+enum {
+ BD957X_VD50,
+ BD957X_VD18,
+ BD957X_VDDDR,
+ BD957X_VD10,
+ BD957X_VOUTL1,
+ BD957X_VOUTS1,
+};
+
+#define BD957X_REG_SMRB_ASSERT 0x15
+#define BD957X_REG_PMIC_INTERNAL_STAT 0x20
+#define BD957X_REG_INT_THERM_STAT 0x23
+#define BD957X_REG_INT_THERM_MASK 0x24
+#define BD957X_REG_INT_OVP_STAT 0x25
+#define BD957X_REG_INT_SCP_STAT 0x26
+#define BD957X_REG_INT_OCP_STAT 0x27
+#define BD957X_REG_INT_OVD_STAT 0x28
+#define BD957X_REG_INT_UVD_STAT 0x29
+#define BD957X_REG_INT_UVP_STAT 0x2a
+#define BD957X_REG_INT_SYS_STAT 0x2b
+#define BD957X_REG_INT_SYS_MASK 0x2c
+#define BD957X_REG_INT_MAIN_STAT 0x30
+#define BD957X_REG_INT_MAIN_MASK 0x31
+
+#define BD957X_REG_WDT_CONF 0x16
+
+#define BD957X_REG_POW_TRIGGER1 0x41
+#define BD957X_REG_POW_TRIGGER2 0x42
+#define BD957X_REG_POW_TRIGGER3 0x43
+#define BD957X_REG_POW_TRIGGER4 0x44
+#define BD957X_REG_POW_TRIGGERL1 0x45
+#define BD957X_REG_POW_TRIGGERS1 0x46
+
+#define BD957X_REGULATOR_EN_MASK 0xff
+#define BD957X_REGULATOR_DIS_VAL 0xff
+
+#define BD957X_VSEL_REG_MASK 0xff
+
+#define BD957X_MASK_VOUT1_TUNE 0x87
+#define BD957X_MASK_VOUT2_TUNE 0x87
+#define BD957X_MASK_VOUT3_TUNE 0x1f
+#define BD957X_MASK_VOUT4_TUNE 0x1f
+#define BD957X_MASK_VOUTL1_TUNE 0x87
+
+#define BD957X_REG_VOUT1_TUNE 0x50
+#define BD957X_REG_VOUT2_TUNE 0x53
+#define BD957X_REG_VOUT3_TUNE 0x56
+#define BD957X_REG_VOUT4_TUNE 0x59
+#define BD957X_REG_VOUTL1_TUNE 0x5c
+
+#define BD957X_MAX_REGISTER 0x61
+
+#endif
diff --git a/include/linux/mfd/rohm-generic.h b/include/linux/mfd/rohm-generic.h
index 66f673c35303..ac6787464004 100644
--- a/include/linux/mfd/rohm-generic.h
+++ b/include/linux/mfd/rohm-generic.h
@@ -14,6 +14,8 @@ enum rohm_chip_type {
ROHM_CHIP_TYPE_BD71828,
ROHM_CHIP_TYPE_BD9571,
ROHM_CHIP_TYPE_BD9574,
+ ROHM_CHIP_TYPE_BD9576,
+ ROHM_CHIP_TYPE_BD9573,
ROHM_CHIP_TYPE_AMOUNT
};
--
2.25.4
--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND
~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH v9 3/6] mfd: bd9576: Add IRQ support
2021-03-10 8:02 [PATCH v9 0/6] Support ROHM BD9576MUF and BD9573MUF PMICs Matti Vaittinen
2021-03-10 8:05 ` [PATCH v9 1/6] dt_bindings: mfd: Add " Matti Vaittinen
2021-03-10 8:06 ` [PATCH v9 2/6] mfd: Support ROHM BD9576MUF and BD9573MUF Matti Vaittinen
@ 2021-03-10 8:08 ` Matti Vaittinen
2021-03-10 8:08 ` [PATCH v9 4/6] wdt: Support wdt on ROHM BD9576MUF and BD9573MUF Matti Vaittinen
` (3 subsequent siblings)
6 siblings, 0 replies; 8+ messages in thread
From: Matti Vaittinen @ 2021-03-10 8:08 UTC (permalink / raw)
To: matti.vaittinen, mazziesaccount
Cc: Lee Jones, Rob Herring, Matti Vaittinen, Wim Van Sebroeck,
Guenter Roeck, devicetree, linux-kernel, linux-power,
linux-watchdog
BD9573 and BD9576 support set of "protection" interrupts for "fatal"
issues. Those lead to SOC reset as PMIC shuts the power outputs. Thus
there is no relevant IRQ handling for them.
Few "detection" interrupts were added to the BD9576 with the idea that
SOC could take some recovery-action before error gets unrecoverable.
Unfortunately the BD9576 interrupt logic was not re-evaluated. IRQs
are not designed to be properly acknowleged - and IRQ line is kept
active for whole duration of error condition (in comparison to
informing only about state change).
For above reason, do not consider missing IRQ as error.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
Changes from v8:
- used designated initializers for MFD cell arrays
- styling
drivers/mfd/rohm-bd9576.c | 90 +++++++++++++++++++++++++++++++--
include/linux/mfd/rohm-bd957x.h | 62 +++++++++++++++++++++++
2 files changed, 147 insertions(+), 5 deletions(-)
diff --git a/drivers/mfd/rohm-bd9576.c b/drivers/mfd/rohm-bd9576.c
index 2dbda1f401e2..6661a27d69a8 100644
--- a/drivers/mfd/rohm-bd9576.c
+++ b/drivers/mfd/rohm-bd9576.c
@@ -17,14 +17,30 @@
#include <linux/regmap.h>
#include <linux/types.h>
+enum {
+ BD957X_REGULATOR_CELL,
+ BD957X_WDT_CELL,
+};
+
+/*
+ * Due to the BD9576MUF nasty IRQ behaiour we don't always populate IRQs.
+ * These will be added to regulator resources only if IRQ information for the
+ * PMIC is populated in device-tree.
+ */
+static const struct resource bd9576_regulator_irqs[] = {
+ DEFINE_RES_IRQ_NAMED(BD9576_INT_THERM, "bd9576-temp"),
+ DEFINE_RES_IRQ_NAMED(BD9576_INT_OVD, "bd9576-ovd"),
+ DEFINE_RES_IRQ_NAMED(BD9576_INT_UVD, "bd9576-uvd"),
+};
+
static struct mfd_cell bd9573_mfd_cells[] = {
- { .name = "bd9573-regulator", },
- { .name = "bd9576-wdt", },
+ [BD957X_REGULATOR_CELL] = { .name = "bd9573-regulator", },
+ [BD957X_WDT_CELL] = { .name = "bd9576-wdt", },
};
static struct mfd_cell bd9576_mfd_cells[] = {
- { .name = "bd9576-regulator", },
- { .name = "bd9576-wdt", },
+ [BD957X_REGULATOR_CELL] = { .name = "bd9576-regulator", },
+ [BD957X_WDT_CELL] = { .name = "bd9576-wdt", },
};
static const struct regmap_range volatile_ranges[] = {
@@ -49,6 +65,29 @@ static struct regmap_config bd957x_regmap = {
.cache_type = REGCACHE_RBTREE,
};
+static struct regmap_irq bd9576_irqs[] = {
+ REGMAP_IRQ_REG(BD9576_INT_THERM, 0, BD957X_MASK_INT_MAIN_THERM),
+ REGMAP_IRQ_REG(BD9576_INT_OVP, 0, BD957X_MASK_INT_MAIN_OVP),
+ REGMAP_IRQ_REG(BD9576_INT_SCP, 0, BD957X_MASK_INT_MAIN_SCP),
+ REGMAP_IRQ_REG(BD9576_INT_OCP, 0, BD957X_MASK_INT_MAIN_OCP),
+ REGMAP_IRQ_REG(BD9576_INT_OVD, 0, BD957X_MASK_INT_MAIN_OVD),
+ REGMAP_IRQ_REG(BD9576_INT_UVD, 0, BD957X_MASK_INT_MAIN_UVD),
+ REGMAP_IRQ_REG(BD9576_INT_UVP, 0, BD957X_MASK_INT_MAIN_UVP),
+ REGMAP_IRQ_REG(BD9576_INT_SYS, 0, BD957X_MASK_INT_MAIN_SYS),
+};
+
+static struct regmap_irq_chip bd9576_irq_chip = {
+ .name = "bd9576_irq",
+ .irqs = &bd9576_irqs[0],
+ .num_irqs = ARRAY_SIZE(bd9576_irqs),
+ .status_base = BD957X_REG_INT_MAIN_STAT,
+ .mask_base = BD957X_REG_INT_MAIN_MASK,
+ .ack_base = BD957X_REG_INT_MAIN_STAT,
+ .init_ack_masked = true,
+ .num_regs = 1,
+ .irq_reg_stride = 1,
+};
+
static int bd957x_i2c_probe(struct i2c_client *i2c,
const struct i2c_device_id *id)
{
@@ -57,6 +96,8 @@ static int bd957x_i2c_probe(struct i2c_client *i2c,
struct mfd_cell *cells;
int num_cells;
unsigned long chip_type;
+ struct irq_domain *domain;
+ bool usable_irqs;
chip_type = (unsigned long)of_device_get_match_data(&i2c->dev);
@@ -64,10 +105,16 @@ static int bd957x_i2c_probe(struct i2c_client *i2c,
case ROHM_CHIP_TYPE_BD9576:
cells = bd9576_mfd_cells;
num_cells = ARRAY_SIZE(bd9576_mfd_cells);
+ usable_irqs = !!i2c->irq;
break;
case ROHM_CHIP_TYPE_BD9573:
cells = bd9573_mfd_cells;
num_cells = ARRAY_SIZE(bd9573_mfd_cells);
+ /*
+ * BD9573 only supports fatal IRQs which we can not handle
+ * because SoC is going to lose the power.
+ */
+ usable_irqs = false;
break;
default:
dev_err(&i2c->dev, "Unknown device type");
@@ -80,8 +127,41 @@ static int bd957x_i2c_probe(struct i2c_client *i2c,
return PTR_ERR(regmap);
}
+ /*
+ * BD9576 behaves badly. It kepts IRQ line asserted for the whole
+ * duration of detected HW condition (like over temperature). So we
+ * don't require IRQ to be populated.
+ * If IRQ information is not given, then we mask all IRQs and do not
+ * provide IRQ resources to regulator driver - which then just omits
+ * the notifiers.
+ */
+ if (usable_irqs) {
+ struct regmap_irq_chip_data *irq_data;
+ struct mfd_cell *regulators;
+
+ regulators = &bd9576_mfd_cells[BD957X_REGULATOR_CELL];
+ regulators->resources = bd9576_regulator_irqs;
+ regulators->num_resources = ARRAY_SIZE(bd9576_regulator_irqs);
+
+ ret = devm_regmap_add_irq_chip(&i2c->dev, regmap, i2c->irq,
+ IRQF_ONESHOT, 0,
+ &bd9576_irq_chip, &irq_data);
+ if (ret) {
+ dev_err(&i2c->dev, "Failed to add IRQ chip\n");
+ return ret;
+ }
+ domain = regmap_irq_get_domain(irq_data);
+ } else {
+ ret = regmap_update_bits(regmap, BD957X_REG_INT_MAIN_MASK,
+ BD957X_MASK_INT_ALL,
+ BD957X_MASK_INT_ALL);
+ if (ret)
+ return ret;
+ domain = NULL;
+ }
+
ret = devm_mfd_add_devices(&i2c->dev, PLATFORM_DEVID_AUTO, cells,
- num_cells, NULL, 0, NULL);
+ num_cells, NULL, 0, domain);
if (ret)
dev_err(&i2c->dev, "Failed to create subdevices\n");
diff --git a/include/linux/mfd/rohm-bd957x.h b/include/linux/mfd/rohm-bd957x.h
index a631abb2c101..ddb396ff2da5 100644
--- a/include/linux/mfd/rohm-bd957x.h
+++ b/include/linux/mfd/rohm-bd957x.h
@@ -13,6 +13,55 @@ enum {
BD957X_VOUTS1,
};
+/*
+ * The BD9576 has own IRQ 'blocks' for:
+ * - I2C/thermal,
+ * - Over voltage protection
+ * - Short-circuit protection
+ * - Over current protection
+ * - Over voltage detection
+ * - Under voltage detection
+ * - Under voltage protection
+ * - 'system interrupt'.
+ *
+ * Each of the blocks have a status register giving more accurate IRQ source
+ * information - for example which of the regulators have over-voltage.
+ *
+ * On top of this, there is "main IRQ" status register where each bit indicates
+ * which of sub-blocks have active IRQs. Fine. That would fit regmap-irq main
+ * status handling. Except that:
+ * - Only some sub-IRQs can be masked.
+ * - The IRQ informs us about fault-condition, not when fault state changes.
+ * The IRQ line it is kept asserted until the detected condition is acked
+ * AND cleared in HW. This is annoying for IRQs like the one informing high
+ * temperature because if IRQ is not disabled it keeps the CPU in IRQ
+ * handling loop.
+ *
+ * For now we do just use the main-IRQ register as source for our IRQ
+ * information and bind the regmap-irq to this. We leave fine-grained sub-IRQ
+ * register handling to handlers in sub-devices. The regulator driver shall
+ * read which regulators are source for problem - or if the detected error is
+ * regulator temperature error. The sub-drivers do also handle masking of "sub-
+ * IRQs" if this is supported/needed.
+ *
+ * To overcome the problem with HW keeping IRQ asserted we do call
+ * disable_irq_nosync() from sub-device handler and add a delayed work to
+ * re-enable IRQ roughly 1 second later. This should keep our CPU out of
+ * busy-loop.
+ */
+#define IRQS_SILENT_MS 1000
+
+enum {
+ BD9576_INT_THERM,
+ BD9576_INT_OVP,
+ BD9576_INT_SCP,
+ BD9576_INT_OCP,
+ BD9576_INT_OVD,
+ BD9576_INT_UVD,
+ BD9576_INT_UVP,
+ BD9576_INT_SYS,
+};
+
#define BD957X_REG_SMRB_ASSERT 0x15
#define BD957X_REG_PMIC_INTERNAL_STAT 0x20
#define BD957X_REG_INT_THERM_STAT 0x23
@@ -28,6 +77,19 @@ enum {
#define BD957X_REG_INT_MAIN_STAT 0x30
#define BD957X_REG_INT_MAIN_MASK 0x31
+#define UVD_IRQ_VALID_MASK 0x6F
+#define OVD_IRQ_VALID_MASK 0x2F
+
+#define BD957X_MASK_INT_MAIN_THERM BIT(0)
+#define BD957X_MASK_INT_MAIN_OVP BIT(1)
+#define BD957X_MASK_INT_MAIN_SCP BIT(2)
+#define BD957X_MASK_INT_MAIN_OCP BIT(3)
+#define BD957X_MASK_INT_MAIN_OVD BIT(4)
+#define BD957X_MASK_INT_MAIN_UVD BIT(5)
+#define BD957X_MASK_INT_MAIN_UVP BIT(6)
+#define BD957X_MASK_INT_MAIN_SYS BIT(7)
+#define BD957X_MASK_INT_ALL 0xff
+
#define BD957X_REG_WDT_CONF 0x16
#define BD957X_REG_POW_TRIGGER1 0x41
--
2.25.4
--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND
~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH v9 4/6] wdt: Support wdt on ROHM BD9576MUF and BD9573MUF
2021-03-10 8:02 [PATCH v9 0/6] Support ROHM BD9576MUF and BD9573MUF PMICs Matti Vaittinen
` (2 preceding siblings ...)
2021-03-10 8:08 ` [PATCH v9 3/6] mfd: bd9576: Add IRQ support Matti Vaittinen
@ 2021-03-10 8:08 ` Matti Vaittinen
2021-03-10 8:09 ` [PATCH v9 5/6] MAINTAINERS: Add ROHM BD9576MUF and BD9573MUF drivers Matti Vaittinen
` (2 subsequent siblings)
6 siblings, 0 replies; 8+ messages in thread
From: Matti Vaittinen @ 2021-03-10 8:08 UTC (permalink / raw)
To: matti.vaittinen, mazziesaccount
Cc: Lee Jones, Rob Herring, Matti Vaittinen, Wim Van Sebroeck,
Guenter Roeck, devicetree, linux-kernel, linux-power,
linux-watchdog
Add Watchdog support for ROHM BD9576MUF and BD9573MUF PMICs which are
mainly used to power the R-Car series processors. The watchdog is
pinged using a GPIO and enabled using another GPIO. Additionally
watchdog time-out can be configured to HW prior starting the watchdog.
Watchdog timeout can be configured to detect only delayed ping or in
a window mode where also too fast pings are detected.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
---
No changes from v8
drivers/watchdog/Kconfig | 13 ++
drivers/watchdog/Makefile | 1 +
drivers/watchdog/bd9576_wdt.c | 291 ++++++++++++++++++++++++++++++++++
3 files changed, 305 insertions(+)
create mode 100644 drivers/watchdog/bd9576_wdt.c
diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
index 1fe0042a48d2..355100dad60a 100644
--- a/drivers/watchdog/Kconfig
+++ b/drivers/watchdog/Kconfig
@@ -172,6 +172,19 @@ config BD70528_WATCHDOG
Alternatively say M to compile the driver as a module,
which will be called bd70528_wdt.
+config BD957XMUF_WATCHDOG
+ tristate "ROHM BD9576MUF and BD9573MUF PMIC Watchdog"
+ depends on MFD_ROHM_BD957XMUF
+ select WATCHDOG_CORE
+ help
+ Support for the watchdog in the ROHM BD9576 and BD9573 PMICs.
+ These PMIC ICs contain watchdog block which can be configured
+ to toggle reset line if SoC fails to ping watchdog via GPIO.
+
+ Say Y here to include support for the ROHM BD9576 or BD9573
+ watchdog. Alternatively say M to compile the driver as a module,
+ which will be called bd9576_wdt.
+
config DA9052_WATCHDOG
tristate "Dialog DA9052 Watchdog"
depends on PMIC_DA9052 || COMPILE_TEST
diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
index f3a6540e725e..a7eade8b4d45 100644
--- a/drivers/watchdog/Makefile
+++ b/drivers/watchdog/Makefile
@@ -204,6 +204,7 @@ obj-$(CONFIG_XEN_WDT) += xen_wdt.o
# Architecture Independent
obj-$(CONFIG_BD70528_WATCHDOG) += bd70528_wdt.o
+obj-$(CONFIG_BD957XMUF_WATCHDOG) += bd9576_wdt.o
obj-$(CONFIG_DA9052_WATCHDOG) += da9052_wdt.o
obj-$(CONFIG_DA9055_WATCHDOG) += da9055_wdt.o
obj-$(CONFIG_DA9062_WATCHDOG) += da9062_wdt.o
diff --git a/drivers/watchdog/bd9576_wdt.c b/drivers/watchdog/bd9576_wdt.c
new file mode 100644
index 000000000000..0b6999f3b6e8
--- /dev/null
+++ b/drivers/watchdog/bd9576_wdt.c
@@ -0,0 +1,291 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2020 ROHM Semiconductors
+ *
+ * ROHM BD9576MUF and BD9573MUF Watchdog driver
+ */
+
+#include <linux/err.h>
+#include <linux/gpio/consumer.h>
+#include <linux/mfd/rohm-bd957x.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/watchdog.h>
+
+static bool nowayout;
+module_param(nowayout, bool, 0);
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default=\"false\")");
+
+#define HW_MARGIN_MIN 2
+#define HW_MARGIN_MAX 4416
+#define BD957X_WDT_DEFAULT_MARGIN 4416
+#define WATCHDOG_TIMEOUT 30
+
+struct bd9576_wdt_priv {
+ struct gpio_desc *gpiod_ping;
+ struct gpio_desc *gpiod_en;
+ struct device *dev;
+ struct regmap *regmap;
+ bool always_running;
+ struct watchdog_device wdd;
+};
+
+static void bd9576_wdt_disable(struct bd9576_wdt_priv *priv)
+{
+ gpiod_set_value_cansleep(priv->gpiod_en, 0);
+}
+
+static int bd9576_wdt_ping(struct watchdog_device *wdd)
+{
+ struct bd9576_wdt_priv *priv = watchdog_get_drvdata(wdd);
+
+ /* Pulse */
+ gpiod_set_value_cansleep(priv->gpiod_ping, 1);
+ gpiod_set_value_cansleep(priv->gpiod_ping, 0);
+
+ return 0;
+}
+
+static int bd9576_wdt_start(struct watchdog_device *wdd)
+{
+ struct bd9576_wdt_priv *priv = watchdog_get_drvdata(wdd);
+
+ gpiod_set_value_cansleep(priv->gpiod_en, 1);
+
+ return bd9576_wdt_ping(wdd);
+}
+
+static int bd9576_wdt_stop(struct watchdog_device *wdd)
+{
+ struct bd9576_wdt_priv *priv = watchdog_get_drvdata(wdd);
+
+ if (!priv->always_running)
+ bd9576_wdt_disable(priv);
+ else
+ set_bit(WDOG_HW_RUNNING, &wdd->status);
+
+ return 0;
+}
+
+static const struct watchdog_info bd957x_wdt_ident = {
+ .options = WDIOF_MAGICCLOSE | WDIOF_KEEPALIVEPING |
+ WDIOF_SETTIMEOUT,
+ .identity = "BD957x Watchdog",
+};
+
+static const struct watchdog_ops bd957x_wdt_ops = {
+ .owner = THIS_MODULE,
+ .start = bd9576_wdt_start,
+ .stop = bd9576_wdt_stop,
+ .ping = bd9576_wdt_ping,
+};
+
+/* Unit is hundreds of uS */
+#define FASTNG_MIN 23
+
+static int find_closest_fast(int target, int *sel, int *val)
+{
+ int i;
+ int window = FASTNG_MIN;
+
+ for (i = 0; i < 8 && window < target; i++)
+ window <<= 1;
+
+ *val = window;
+ *sel = i;
+
+ if (i == 8)
+ return -EINVAL;
+
+ return 0;
+
+}
+
+static int find_closest_slow_by_fast(int fast_val, int target, int *slowsel)
+{
+ int sel;
+ static const int multipliers[] = {2, 3, 7, 15};
+
+ for (sel = 0; sel < ARRAY_SIZE(multipliers) &&
+ multipliers[sel] * fast_val < target; sel++)
+ ;
+
+ if (sel == ARRAY_SIZE(multipliers))
+ return -EINVAL;
+
+ *slowsel = sel;
+
+ return 0;
+}
+
+static int find_closest_slow(int target, int *slow_sel, int *fast_sel)
+{
+ static const int multipliers[] = {2, 3, 7, 15};
+ int i, j;
+ int val = 0;
+ int window = FASTNG_MIN;
+
+ for (i = 0; i < 8; i++) {
+ for (j = 0; j < ARRAY_SIZE(multipliers); j++) {
+ int slow;
+
+ slow = window * multipliers[j];
+ if (slow >= target && (!val || slow < val)) {
+ val = slow;
+ *fast_sel = i;
+ *slow_sel = j;
+ }
+ }
+ window <<= 1;
+ }
+ if (!val)
+ return -EINVAL;
+
+ return 0;
+}
+
+#define BD957X_WDG_TYPE_WINDOW BIT(5)
+#define BD957X_WDG_TYPE_SLOW 0
+#define BD957X_WDG_TYPE_MASK BIT(5)
+#define BD957X_WDG_NG_RATIO_MASK 0x18
+#define BD957X_WDG_FASTNG_MASK 0x7
+
+static int bd957x_set_wdt_mode(struct bd9576_wdt_priv *priv, int hw_margin,
+ int hw_margin_min)
+{
+ int ret, fastng, slowng, type, reg, mask;
+ struct device *dev = priv->dev;
+
+ /* convert to 100uS */
+ hw_margin *= 10;
+ hw_margin_min *= 10;
+ if (hw_margin_min) {
+ int min;
+
+ type = BD957X_WDG_TYPE_WINDOW;
+ dev_dbg(dev, "Setting type WINDOW 0x%x\n", type);
+ ret = find_closest_fast(hw_margin_min, &fastng, &min);
+ if (ret) {
+ dev_err(dev, "bad WDT window for fast timeout\n");
+ return ret;
+ }
+
+ ret = find_closest_slow_by_fast(min, hw_margin, &slowng);
+ if (ret) {
+ dev_err(dev, "bad WDT window\n");
+ return ret;
+ }
+
+ } else {
+ type = BD957X_WDG_TYPE_SLOW;
+ dev_dbg(dev, "Setting type SLOW 0x%x\n", type);
+ ret = find_closest_slow(hw_margin, &slowng, &fastng);
+ if (ret) {
+ dev_err(dev, "bad WDT window\n");
+ return ret;
+ }
+ }
+
+ slowng <<= ffs(BD957X_WDG_NG_RATIO_MASK) - 1;
+ reg = type | slowng | fastng;
+ mask = BD957X_WDG_TYPE_MASK | BD957X_WDG_NG_RATIO_MASK |
+ BD957X_WDG_FASTNG_MASK;
+ ret = regmap_update_bits(priv->regmap, BD957X_REG_WDT_CONF,
+ mask, reg);
+
+ return ret;
+}
+
+static int bd9576_wdt_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->parent->of_node;
+ struct bd9576_wdt_priv *priv;
+ u32 hw_margin[2];
+ u32 hw_margin_max = BD957X_WDT_DEFAULT_MARGIN, hw_margin_min = 0;
+ int ret;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, priv);
+
+ priv->dev = dev;
+ priv->regmap = dev_get_regmap(dev->parent, NULL);
+ if (!priv->regmap) {
+ dev_err(dev, "No regmap found\n");
+ return -ENODEV;
+ }
+
+ priv->gpiod_en = devm_gpiod_get_from_of_node(dev, dev->parent->of_node,
+ "rohm,watchdog-enable-gpios",
+ 0, GPIOD_OUT_LOW,
+ "watchdog-enable");
+ if (IS_ERR(priv->gpiod_en))
+ return dev_err_probe(dev, PTR_ERR(priv->gpiod_en),
+ "getting watchdog-enable GPIO failed\n");
+
+ priv->gpiod_ping = devm_gpiod_get_from_of_node(dev, dev->parent->of_node,
+ "rohm,watchdog-ping-gpios",
+ 0, GPIOD_OUT_LOW,
+ "watchdog-ping");
+ if (IS_ERR(priv->gpiod_ping))
+ return dev_err_probe(dev, PTR_ERR(priv->gpiod_ping),
+ "getting watchdog-ping GPIO failed\n");
+
+ ret = of_property_read_variable_u32_array(np, "rohm,hw-timeout-ms",
+ &hw_margin[0], 1, 2);
+ if (ret < 0 && ret != -EINVAL)
+ return ret;
+
+ if (ret == 1)
+ hw_margin_max = hw_margin[0];
+
+ if (ret == 2) {
+ hw_margin_max = hw_margin[1];
+ hw_margin_min = hw_margin[0];
+ }
+
+ ret = bd957x_set_wdt_mode(priv, hw_margin_max, hw_margin_min);
+ if (ret)
+ return ret;
+
+ priv->always_running = of_property_read_bool(np, "always-running");
+
+ watchdog_set_drvdata(&priv->wdd, priv);
+
+ priv->wdd.info = &bd957x_wdt_ident;
+ priv->wdd.ops = &bd957x_wdt_ops;
+ priv->wdd.min_hw_heartbeat_ms = hw_margin_min;
+ priv->wdd.max_hw_heartbeat_ms = hw_margin_max;
+ priv->wdd.parent = dev;
+ priv->wdd.timeout = WATCHDOG_TIMEOUT;
+
+ watchdog_init_timeout(&priv->wdd, 0, dev);
+ watchdog_set_nowayout(&priv->wdd, nowayout);
+
+ watchdog_stop_on_reboot(&priv->wdd);
+
+ if (priv->always_running)
+ bd9576_wdt_start(&priv->wdd);
+
+ return devm_watchdog_register_device(dev, &priv->wdd);
+}
+
+static struct platform_driver bd9576_wdt_driver = {
+ .driver = {
+ .name = "bd9576-wdt",
+ },
+ .probe = bd9576_wdt_probe,
+};
+
+module_platform_driver(bd9576_wdt_driver);
+
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("ROHM BD9576/BD9573 Watchdog driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:bd9576-wdt");
--
2.25.4
--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND
~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH v9 5/6] MAINTAINERS: Add ROHM BD9576MUF and BD9573MUF drivers
2021-03-10 8:02 [PATCH v9 0/6] Support ROHM BD9576MUF and BD9573MUF PMICs Matti Vaittinen
` (3 preceding siblings ...)
2021-03-10 8:08 ` [PATCH v9 4/6] wdt: Support wdt on ROHM BD9576MUF and BD9573MUF Matti Vaittinen
@ 2021-03-10 8:09 ` Matti Vaittinen
2021-03-10 8:11 ` [PATCH v9 6/6] mfd: bd9576: Add safety limit/monitoring registers Matti Vaittinen
2021-03-10 11:05 ` [GIT PULL] Immutable branch between MFD and Watchdog due for the v5.13 merge window Lee Jones
6 siblings, 0 replies; 8+ messages in thread
From: Matti Vaittinen @ 2021-03-10 8:09 UTC (permalink / raw)
To: matti.vaittinen, mazziesaccount
Cc: Lee Jones, Rob Herring, Matti Vaittinen, Wim Van Sebroeck,
Guenter Roeck, devicetree, linux-kernel, linux-power,
linux-watchdog
Add maintainer entries for ROHM BD9576MUF and ROHM BD9573MUF drivers.
MFD, regulator and watchdog drivers were introduced for these PMICs.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
---
No changes from v8
MAINTAINERS | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index d92f85ca831d..10d5f706c8b1 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -15456,16 +15456,20 @@ F: drivers/gpio/gpio-bd71828.c
F: drivers/mfd/rohm-bd70528.c
F: drivers/mfd/rohm-bd71828.c
F: drivers/mfd/rohm-bd718x7.c
+F: drivers/mfd/rohm-bd9576.c
F: drivers/power/supply/bd70528-charger.c
F: drivers/regulator/bd70528-regulator.c
F: drivers/regulator/bd71828-regulator.c
F: drivers/regulator/bd718x7-regulator.c
+F: drivers/regulator/bd9576-regulator.c
F: drivers/regulator/rohm-regulator.c
F: drivers/rtc/rtc-bd70528.c
F: drivers/watchdog/bd70528_wdt.c
+F: drivers/watchdog/bd9576_wdt.c
F: include/linux/mfd/rohm-bd70528.h
F: include/linux/mfd/rohm-bd71828.h
F: include/linux/mfd/rohm-bd718x7.h
+F: include/linux/mfd/rohm-bd957x.h
F: include/linux/mfd/rohm-generic.h
F: include/linux/mfd/rohm-shared.h
--
2.25.4
--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND
~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH v9 6/6] mfd: bd9576: Add safety limit/monitoring registers
2021-03-10 8:02 [PATCH v9 0/6] Support ROHM BD9576MUF and BD9573MUF PMICs Matti Vaittinen
` (4 preceding siblings ...)
2021-03-10 8:09 ` [PATCH v9 5/6] MAINTAINERS: Add ROHM BD9576MUF and BD9573MUF drivers Matti Vaittinen
@ 2021-03-10 8:11 ` Matti Vaittinen
2021-03-10 11:05 ` [GIT PULL] Immutable branch between MFD and Watchdog due for the v5.13 merge window Lee Jones
6 siblings, 0 replies; 8+ messages in thread
From: Matti Vaittinen @ 2021-03-10 8:11 UTC (permalink / raw)
To: matti.vaittinen, mazziesaccount
Cc: Lee Jones, Rob Herring, Matti Vaittinen, Wim Van Sebroeck,
Guenter Roeck, devicetree, linux-kernel, linux-power,
linux-watchdog, Mark Brown
ROHM BD9576 contains safety features like over/under voltage detection,
over curren detection and over temperature detection. Add the
configuration register information.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
---
No changes from v8
include/linux/mfd/rohm-bd957x.h | 19 +++++++++++++++++++
1 file changed, 19 insertions(+)
diff --git a/include/linux/mfd/rohm-bd957x.h b/include/linux/mfd/rohm-bd957x.h
index ddb396ff2da5..acc920b64f75 100644
--- a/include/linux/mfd/rohm-bd957x.h
+++ b/include/linux/mfd/rohm-bd957x.h
@@ -116,6 +116,25 @@ enum {
#define BD957X_REG_VOUT4_TUNE 0x59
#define BD957X_REG_VOUTL1_TUNE 0x5c
+#define BD9576_REG_VOUT1_OVD 0x51
+#define BD9576_REG_VOUT1_UVD 0x52
+#define BD9576_REG_VOUT2_OVD 0x54
+#define BD9576_REG_VOUT2_UVD 0x55
+#define BD9576_REG_VOUT3_OVD 0x57
+#define BD9576_REG_VOUT3_UVD 0x58
+#define BD9576_REG_VOUT4_OVD 0x5a
+#define BD9576_REG_VOUT4_UVD 0x5b
+#define BD9576_REG_VOUTL1_OVD 0x5d
+#define BD9576_REG_VOUTL1_UVD 0x5e
+
+#define BD9576_MASK_XVD 0x7f
+
+#define BD9576_REG_VOUT1S_OCW 0x5f
+#define BD9576_REG_VOUT1S_OCP 0x60
+
+#define BD9576_MASK_VOUT1S_OCW 0x3f
+#define BD9576_MASK_VOUT1S_OCP 0x3f
+
#define BD957X_MAX_REGISTER 0x61
#endif
--
2.25.4
--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND
~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]
^ permalink raw reply related [flat|nested] 8+ messages in thread* [GIT PULL] Immutable branch between MFD and Watchdog due for the v5.13 merge window
2021-03-10 8:02 [PATCH v9 0/6] Support ROHM BD9576MUF and BD9573MUF PMICs Matti Vaittinen
` (5 preceding siblings ...)
2021-03-10 8:11 ` [PATCH v9 6/6] mfd: bd9576: Add safety limit/monitoring registers Matti Vaittinen
@ 2021-03-10 11:05 ` Lee Jones
6 siblings, 0 replies; 8+ messages in thread
From: Lee Jones @ 2021-03-10 11:05 UTC (permalink / raw)
To: Matti Vaittinen
Cc: mazziesaccount, Rob Herring, Wim Van Sebroeck, Guenter Roeck,
devicetree, linux-kernel, linux-power, linux-watchdog
Enjoy!
The following changes since commit a38fd8748464831584a19438cbb3082b5a2dab15:
Linux 5.12-rc2 (2021-03-05 17:33:41 -0800)
are available in the Git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git ib-mfd-watchdog-v5.13
for you to fetch changes up to 42fc191d60e6d5fd8c52e7afa8bccdc912947ce4:
mfd: bd9576: Add safety limit/monitoring registers (2021-03-10 10:59:03 +0000)
----------------------------------------------------------------
Immutable branch between MFD and Watchdog due for the v5.13 merge window
----------------------------------------------------------------
Matti Vaittinen (6):
dt_bindings: mfd: Add ROHM BD9576MUF and BD9573MUF PMICs
mfd: Support ROHM BD9576MUF and BD9573MUF
mfd: bd9576: Add IRQ support
wdt: Support wdt on ROHM BD9576MUF and BD9573MUF
MAINTAINERS: Add ROHM BD9576MUF and BD9573MUF drivers
mfd: bd9576: Add safety limit/monitoring registers
.../devicetree/bindings/mfd/rohm,bd9576-pmic.yaml | 123 +++++++++
MAINTAINERS | 4 +
drivers/mfd/Kconfig | 11 +
drivers/mfd/Makefile | 1 +
drivers/mfd/rohm-bd9576.c | 189 +++++++++++++
drivers/watchdog/Kconfig | 13 +
drivers/watchdog/Makefile | 1 +
drivers/watchdog/bd9576_wdt.c | 291 +++++++++++++++++++++
include/linux/mfd/rohm-bd957x.h | 140 ++++++++++
include/linux/mfd/rohm-generic.h | 2 +
10 files changed, 775 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd9576-pmic.yaml
create mode 100644 drivers/mfd/rohm-bd9576.c
create mode 100644 drivers/watchdog/bd9576_wdt.c
create mode 100644 include/linux/mfd/rohm-bd957x.h
--
Lee Jones [李琼斯]
Senior Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 8+ messages in thread