* [PATCH 1/3] watchdog: Add pm8916 watchdog driver
@ 2018-11-17 8:28 Loic Poulain
2018-11-17 8:28 ` [PATCH 2/3] dt-bindings: watchdog: Add Qualcomm PM8916 watchdog Loic Poulain
` (2 more replies)
0 siblings, 3 replies; 4+ messages in thread
From: Loic Poulain @ 2018-11-17 8:28 UTC (permalink / raw)
To: wim, linux, robh+dt
Cc: linux-arm-msm, linux-watchdog, devicetree, andy.gross, Loic Poulain
The PM816 module is a versatile PMIC with many diverse functions
integrated, including, a watchdog.
This watchdog is subcomponent of the PON (Power On) peripheral,
in the same way as pwrkey/resin buttons.
It works with two timers (2-stages), the first one generates an
IRQ to the main SoC (APQ8016/MSM8916), the second one performs
the reset.
This driver expects the following device hierachy:
[pm8916]->[pm8916-pon]->[pm8916-wdt]
It uses the pm8916 regmap to access PM8916 registers.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
---
drivers/watchdog/Kconfig | 8 ++
drivers/watchdog/Makefile | 1 +
drivers/watchdog/pm8916_wdt.c | 177 ++++++++++++++++++++++++++++++++++++++++++
3 files changed, 186 insertions(+)
create mode 100644 drivers/watchdog/pm8916_wdt.c
diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
index 2d64333..66bab61 100644
--- a/drivers/watchdog/Kconfig
+++ b/drivers/watchdog/Kconfig
@@ -847,6 +847,14 @@ config SPRD_WATCHDOG
Say Y here to include watchdog timer supported
by Spreadtrum system.
+config PM8916_WATCHDOG
+ tristate "QCOM pm8916 pmic watchdog"
+ depends on OF && MFD_SPMI_PMIC
+ select WATCHDOG_CORE
+ help
+ Say Y here to include support watchdog timer embedded into the
+ pm8916 module.
+
# X86 (i386 + ia64 + x86_64) Architecture
config ACQUIRE_WDT
diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
index f69cdff..cc90e72 100644
--- a/drivers/watchdog/Makefile
+++ b/drivers/watchdog/Makefile
@@ -92,6 +92,7 @@ obj-$(CONFIG_STM32_WATCHDOG) += stm32_iwdg.o
obj-$(CONFIG_UNIPHIER_WATCHDOG) += uniphier_wdt.o
obj-$(CONFIG_RTD119X_WATCHDOG) += rtd119x_wdt.o
obj-$(CONFIG_SPRD_WATCHDOG) += sprd_wdt.o
+obj-$(CONFIG_PM8916_WATCHDOG) += pm8916_wdt.o
# X86 (i386 + ia64 + x86_64) Architecture
obj-$(CONFIG_ACQUIRE_WDT) += acquirewdt.o
diff --git a/drivers/watchdog/pm8916_wdt.c b/drivers/watchdog/pm8916_wdt.c
new file mode 100644
index 0000000..36f9763
--- /dev/null
+++ b/drivers/watchdog/pm8916_wdt.c
@@ -0,0 +1,177 @@
+/*
+ * Watchdog driver for QCOM PM8916
+ *
+ * Copyright (C) 2018 Loic Poulain, Linaro <loic.poulain@linaro.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/bitops.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/property.h>
+#include <linux/platform_device.h>
+#include <linux/watchdog.h>
+#include <linux/regmap.h>
+
+#define PM8916_WDT_DEFAULT_TIMEOUT 32
+
+#define PON_PMIC_WD_RESET_S1_TIMER 0x54
+#define PON_PMIC_WD_RESET_S2_TIMER 0x55
+#define PON_PMIC_WD_RESET_S2_CTL 0x56
+#define PON_PMIC_WD_RESET_S2_CTL2 0x57
+#define PON_PMIC_WD_RESET_PET 0x58
+
+#define S2_RESET_EN_MASK BIT(7)
+#define S2_RESET_EN (1 << 7)
+
+#define WATCHDOG_PET_MASK BIT(0)
+
+struct pm8916_wdt {
+ struct device *dev;
+ struct regmap *regmap;
+ struct watchdog_device wdev;
+ u32 baseaddr;
+};
+
+static int pm8916_wdt_start(struct watchdog_device *wdev)
+{
+ struct pm8916_wdt *wdt = watchdog_get_drvdata(wdev);
+
+ return regmap_update_bits(wdt->regmap,
+ wdt->baseaddr + PON_PMIC_WD_RESET_S2_CTL2,
+ S2_RESET_EN_MASK, S2_RESET_EN);
+}
+
+static int pm8916_wdt_stop(struct watchdog_device *wdev)
+{
+ struct pm8916_wdt *wdt = watchdog_get_drvdata(wdev);
+
+ return regmap_update_bits(wdt->regmap,
+ wdt->baseaddr + PON_PMIC_WD_RESET_S2_CTL2,
+ S2_RESET_EN_MASK, 0);
+}
+
+static int pm8916_wdt_ping(struct watchdog_device *wdev)
+{
+ struct pm8916_wdt *wdt = watchdog_get_drvdata(wdev);
+
+ return regmap_update_bits(wdt->regmap,
+ wdt->baseaddr + PON_PMIC_WD_RESET_PET,
+ WATCHDOG_PET_MASK, 1);
+}
+
+static int pm8916_wdt_set_timeout(struct watchdog_device *wdev,
+ unsigned int timeout)
+{
+ struct pm8916_wdt *wdt = watchdog_get_drvdata(wdev);
+ int err;
+
+ wdev->timeout = timeout;
+
+ /* This is a two stages watchdog, set stage-1 timer generate an irq and
+ * stage-2 trigger the reset. In order to respect expected timeout, set
+ * stage-1 timer to timeout and stage-2 to 0.
+ */
+ err = regmap_write(wdt->regmap,
+ wdt->baseaddr + PON_PMIC_WD_RESET_S1_TIMER,
+ timeout);
+ if (err)
+ return err;
+
+ return regmap_write(wdt->regmap,
+ wdt->baseaddr + PON_PMIC_WD_RESET_S2_TIMER,
+ 0);
+}
+
+static const struct watchdog_info pm8916_wdt_ident = {
+ .options = WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING,
+ .identity = "QCOM PM8916 PON WDT",
+};
+
+static const struct watchdog_ops pm8916_wdt_ops = {
+ .owner = THIS_MODULE,
+ .start = pm8916_wdt_start,
+ .stop = pm8916_wdt_stop,
+ .ping = pm8916_wdt_ping,
+ .set_timeout = pm8916_wdt_set_timeout,
+};
+
+static int pm8916_wdt_probe(struct platform_device *pdev)
+{
+ struct pm8916_wdt *wdt;
+ struct device *parent;
+ int err;
+
+ wdt = devm_kzalloc(&pdev->dev, sizeof(*wdt), GFP_KERNEL);
+ if (!wdt)
+ return -ENOMEM;
+
+ wdt->dev = &pdev->dev;
+ parent = pdev->dev.parent;
+
+ /*
+ * The pm8916-pon-wdt is a child of the pon device, which is a child
+ * of the pm8916 mfd device. We want access to the pm8916 registers.
+ * Retrieve regmap from pm8916 (parent->parent) and base address
+ * from pm8916-pon (pon).
+ */
+ wdt->regmap = dev_get_regmap(parent->parent, NULL);
+ if (!wdt->regmap) {
+ dev_err(&pdev->dev, "failed to locate regmap\n");
+ return -ENODEV;
+ }
+
+ err = device_property_read_u32(parent, "reg", &wdt->baseaddr);
+ if (err) {
+ dev_err(&pdev->dev, "failed to get address\n");
+ return err;
+ }
+
+ /* Configure watchdog to hard-reset mode */
+ err = regmap_write(wdt->regmap,
+ wdt->baseaddr + PON_PMIC_WD_RESET_S2_CTL, 0x07);
+ if (err) {
+ dev_err(&pdev->dev, "failed configure watchdog\n");
+ return err;
+ }
+
+ wdt->wdev.info = &pm8916_wdt_ident,
+ wdt->wdev.ops = &pm8916_wdt_ops,
+ wdt->wdev.parent = &pdev->dev;
+ wdt->wdev.min_timeout = 1;
+ wdt->wdev.max_timeout = 127;
+ wdt->wdev.timeout = PM8916_WDT_DEFAULT_TIMEOUT;
+ watchdog_set_drvdata(&wdt->wdev, wdt);
+
+ pm8916_wdt_set_timeout(&wdt->wdev, wdt->wdev.timeout);
+
+ return watchdog_register_device(&wdt->wdev);
+}
+
+static const struct of_device_id pm8916_wdt_id_table[] = {
+ { .compatible = "qcom,pm8916-wdt" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, pm8916_wdt_id_table);
+
+static struct platform_driver pm8916_wdt_driver = {
+ .probe = pm8916_wdt_probe,
+ .driver = {
+ .name = "pm8916-wdt",
+ .of_match_table = of_match_ptr(pm8916_wdt_id_table),
+ },
+};
+module_platform_driver(pm8916_wdt_driver);
+
+MODULE_AUTHOR("Loic Poulain <loic.poulain@linaro.org>");
+MODULE_DESCRIPTION("Qualcomm pm8916 watchdog driver");
+MODULE_LICENSE("GPL v2");
--
2.7.4
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH 2/3] dt-bindings: watchdog: Add Qualcomm PM8916 watchdog
2018-11-17 8:28 [PATCH 1/3] watchdog: Add pm8916 watchdog driver Loic Poulain
@ 2018-11-17 8:28 ` Loic Poulain
2018-11-17 8:28 ` [PATCH 3/3] arm64: dts: qcom: pm8916: Add PON watchdog node Loic Poulain
2018-11-19 21:23 ` [PATCH 1/3] watchdog: Add pm8916 watchdog driver Guenter Roeck
2 siblings, 0 replies; 4+ messages in thread
From: Loic Poulain @ 2018-11-17 8:28 UTC (permalink / raw)
To: wim, linux, robh+dt
Cc: linux-arm-msm, linux-watchdog, devicetree, andy.gross, Loic Poulain
Document support for the Watchdog Timer (WDT) Controller in the
Qualcomm PM8916 PMIC module.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
---
.../bindings/watchdog/qcom,pm8916-wdt.txt | 21 +++++++++++++++++++++
1 file changed, 21 insertions(+)
create mode 100644 Documentation/devicetree/bindings/watchdog/qcom,pm8916-wdt.txt
diff --git a/Documentation/devicetree/bindings/watchdog/qcom,pm8916-wdt.txt b/Documentation/devicetree/bindings/watchdog/qcom,pm8916-wdt.txt
new file mode 100644
index 0000000..08f4003
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/qcom,pm8916-wdt.txt
@@ -0,0 +1,21 @@
+QCOM PM8916 watchdog timer controller
+
+This pm8916 watchdog timer controller must be under pm8916-pon node.
+
+Required properties:
+- compatible: should be "qcom,pm8916-wdt"
+
+Example
+ pm8916_0: pm8916@0 {
+ compatible = "qcom,pm8916", "qcom,spmi-pmic";
+ reg = <0x0 SPMI_USID>;
+
+ pon@800 {
+ compatible = "qcom,pm8916-pon";
+ reg = <0x800>;
+
+ watchdog {
+ compatible = "qcom,pm8916-wdt";
+ };
+ };
+ };
--
2.7.4
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH 3/3] arm64: dts: qcom: pm8916: Add PON watchdog node
2018-11-17 8:28 [PATCH 1/3] watchdog: Add pm8916 watchdog driver Loic Poulain
2018-11-17 8:28 ` [PATCH 2/3] dt-bindings: watchdog: Add Qualcomm PM8916 watchdog Loic Poulain
@ 2018-11-17 8:28 ` Loic Poulain
2018-11-19 21:23 ` [PATCH 1/3] watchdog: Add pm8916 watchdog driver Guenter Roeck
2 siblings, 0 replies; 4+ messages in thread
From: Loic Poulain @ 2018-11-17 8:28 UTC (permalink / raw)
To: wim, linux, robh+dt
Cc: linux-arm-msm, linux-watchdog, devicetree, andy.gross, Loic Poulain
Add watchdog child node to the PM8916 PON device.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
---
arch/arm64/boot/dts/qcom/pm8916.dtsi | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/pm8916.dtsi b/arch/arm64/boot/dts/qcom/pm8916.dtsi
index a05ebaf..4dfaf9b 100644
--- a/arch/arm64/boot/dts/qcom/pm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8916.dtsi
@@ -25,6 +25,10 @@
mode-bootloader = <0x2>;
mode-recovery = <0x1>;
+ watchdog {
+ compatible = "qcom,pm8916-wdt";
+ };
+
pwrkey {
compatible = "qcom,pm8941-pwrkey";
interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
--
2.7.4
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH 1/3] watchdog: Add pm8916 watchdog driver
2018-11-17 8:28 [PATCH 1/3] watchdog: Add pm8916 watchdog driver Loic Poulain
2018-11-17 8:28 ` [PATCH 2/3] dt-bindings: watchdog: Add Qualcomm PM8916 watchdog Loic Poulain
2018-11-17 8:28 ` [PATCH 3/3] arm64: dts: qcom: pm8916: Add PON watchdog node Loic Poulain
@ 2018-11-19 21:23 ` Guenter Roeck
2 siblings, 0 replies; 4+ messages in thread
From: Guenter Roeck @ 2018-11-19 21:23 UTC (permalink / raw)
To: Loic Poulain
Cc: wim, robh+dt, linux-arm-msm, linux-watchdog, devicetree, andy.gross
On Sat, Nov 17, 2018 at 09:28:37AM +0100, Loic Poulain wrote:
> The PM816 module is a versatile PMIC with many diverse functions
> integrated, including, a watchdog.
> This watchdog is subcomponent of the PON (Power On) peripheral,
> in the same way as pwrkey/resin buttons.
> It works with two timers (2-stages), the first one generates an
> IRQ to the main SoC (APQ8016/MSM8916), the second one performs
> the reset.
>
> This driver expects the following device hierachy:
> [pm8916]->[pm8916-pon]->[pm8916-wdt]
>
> It uses the pm8916 regmap to access PM8916 registers.
>
> Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
> ---
> drivers/watchdog/Kconfig | 8 ++
> drivers/watchdog/Makefile | 1 +
> drivers/watchdog/pm8916_wdt.c | 177 ++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 186 insertions(+)
> create mode 100644 drivers/watchdog/pm8916_wdt.c
>
> diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
> index 2d64333..66bab61 100644
> --- a/drivers/watchdog/Kconfig
> +++ b/drivers/watchdog/Kconfig
> @@ -847,6 +847,14 @@ config SPRD_WATCHDOG
> Say Y here to include watchdog timer supported
> by Spreadtrum system.
>
> +config PM8916_WATCHDOG
> + tristate "QCOM pm8916 pmic watchdog"
> + depends on OF && MFD_SPMI_PMIC
> + select WATCHDOG_CORE
> + help
> + Say Y here to include support watchdog timer embedded into the
> + pm8916 module.
> +
> # X86 (i386 + ia64 + x86_64) Architecture
>
> config ACQUIRE_WDT
> diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
> index f69cdff..cc90e72 100644
> --- a/drivers/watchdog/Makefile
> +++ b/drivers/watchdog/Makefile
> @@ -92,6 +92,7 @@ obj-$(CONFIG_STM32_WATCHDOG) += stm32_iwdg.o
> obj-$(CONFIG_UNIPHIER_WATCHDOG) += uniphier_wdt.o
> obj-$(CONFIG_RTD119X_WATCHDOG) += rtd119x_wdt.o
> obj-$(CONFIG_SPRD_WATCHDOG) += sprd_wdt.o
> +obj-$(CONFIG_PM8916_WATCHDOG) += pm8916_wdt.o
>
> # X86 (i386 + ia64 + x86_64) Architecture
> obj-$(CONFIG_ACQUIRE_WDT) += acquirewdt.o
> diff --git a/drivers/watchdog/pm8916_wdt.c b/drivers/watchdog/pm8916_wdt.c
> new file mode 100644
> index 0000000..36f9763
> --- /dev/null
> +++ b/drivers/watchdog/pm8916_wdt.c
> @@ -0,0 +1,177 @@
> +/*
> + * Watchdog driver for QCOM PM8916
> + *
> + * Copyright (C) 2018 Loic Poulain, Linaro <loic.poulain@linaro.org>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
Please use the SPDX license identifier.
> + */
> +
> +#include <linux/bitops.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/property.h>
> +#include <linux/platform_device.h>
> +#include <linux/watchdog.h>
> +#include <linux/regmap.h>
> +
Aplhabetic order, please.
> +#define PM8916_WDT_DEFAULT_TIMEOUT 32
> +
> +#define PON_PMIC_WD_RESET_S1_TIMER 0x54
> +#define PON_PMIC_WD_RESET_S2_TIMER 0x55
> +#define PON_PMIC_WD_RESET_S2_CTL 0x56
> +#define PON_PMIC_WD_RESET_S2_CTL2 0x57
> +#define PON_PMIC_WD_RESET_PET 0x58
> +
> +#define S2_RESET_EN_MASK BIT(7)
> +#define S2_RESET_EN (1 << 7)
Please use tabs. Also, why (1 << 7) instead of BIT(7) ?
Overall, since this is a single bit, having both EN_MASK and EN
seems unnecessary, but if you do,
> +
> +#define WATCHDOG_PET_MASK BIT(0)
> +
please do the same here.
> +struct pm8916_wdt {
> + struct device *dev;
> + struct regmap *regmap;
> + struct watchdog_device wdev;
> + u32 baseaddr;
> +};
> +
> +static int pm8916_wdt_start(struct watchdog_device *wdev)
> +{
> + struct pm8916_wdt *wdt = watchdog_get_drvdata(wdev);
> +
> + return regmap_update_bits(wdt->regmap,
> + wdt->baseaddr + PON_PMIC_WD_RESET_S2_CTL2,
> + S2_RESET_EN_MASK, S2_RESET_EN);
> +}
> +
> +static int pm8916_wdt_stop(struct watchdog_device *wdev)
> +{
> + struct pm8916_wdt *wdt = watchdog_get_drvdata(wdev);
> +
> + return regmap_update_bits(wdt->regmap,
> + wdt->baseaddr + PON_PMIC_WD_RESET_S2_CTL2,
> + S2_RESET_EN_MASK, 0);
> +}
> +
> +static int pm8916_wdt_ping(struct watchdog_device *wdev)
> +{
> + struct pm8916_wdt *wdt = watchdog_get_drvdata(wdev);
> +
> + return regmap_update_bits(wdt->regmap,
> + wdt->baseaddr + PON_PMIC_WD_RESET_PET,
> + WATCHDOG_PET_MASK, 1);
The "1" is really supposed to be BIT(0).
> +}
> +
> +static int pm8916_wdt_set_timeout(struct watchdog_device *wdev,
> + unsigned int timeout)
> +{
> + struct pm8916_wdt *wdt = watchdog_get_drvdata(wdev);
> + int err;
> +
> + wdev->timeout = timeout;
> +
> + /* This is a two stages watchdog, set stage-1 timer generate an irq and
Please use standard multi-line comments.
> + * stage-2 trigger the reset. In order to respect expected timeout, set
> + * stage-1 timer to timeout and stage-2 to 0.
> + */
> + err = regmap_write(wdt->regmap,
> + wdt->baseaddr + PON_PMIC_WD_RESET_S1_TIMER,
> + timeout);
> + if (err)
> + return err;
> +
> + return regmap_write(wdt->regmap,
> + wdt->baseaddr + PON_PMIC_WD_RESET_S2_TIMER,
> + 0);
The watchdog subsystem does support pretimeout, which seems to match the
description here. Not mandatory to support it, but it might make sense.
> +}
> +
> +static const struct watchdog_info pm8916_wdt_ident = {
> + .options = WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING,
No WDIOF_MAGICCLOSE ?
> + .identity = "QCOM PM8916 PON WDT",
> +};
> +
> +static const struct watchdog_ops pm8916_wdt_ops = {
> + .owner = THIS_MODULE,
> + .start = pm8916_wdt_start,
> + .stop = pm8916_wdt_stop,
> + .ping = pm8916_wdt_ping,
> + .set_timeout = pm8916_wdt_set_timeout,
> +};
> +
> +static int pm8916_wdt_probe(struct platform_device *pdev)
> +{
> + struct pm8916_wdt *wdt;
> + struct device *parent;
> + int err;
> +
> + wdt = devm_kzalloc(&pdev->dev, sizeof(*wdt), GFP_KERNEL);
> + if (!wdt)
> + return -ENOMEM;
> +
> + wdt->dev = &pdev->dev;
> + parent = pdev->dev.parent;
> +
> + /*
> + * The pm8916-pon-wdt is a child of the pon device, which is a child
> + * of the pm8916 mfd device. We want access to the pm8916 registers.
> + * Retrieve regmap from pm8916 (parent->parent) and base address
> + * from pm8916-pon (pon).
> + */
> + wdt->regmap = dev_get_regmap(parent->parent, NULL);
> + if (!wdt->regmap) {
> + dev_err(&pdev->dev, "failed to locate regmap\n");
> + return -ENODEV;
> + }
> +
> + err = device_property_read_u32(parent, "reg", &wdt->baseaddr);
> + if (err) {
> + dev_err(&pdev->dev, "failed to get address\n");
... and the user will wonder "what address"
> + return err;
> + }
> +
> + /* Configure watchdog to hard-reset mode */
> + err = regmap_write(wdt->regmap,
> + wdt->baseaddr + PON_PMIC_WD_RESET_S2_CTL, 0x07);
This is where symbolic defines come in handy, even if used only once.
> + if (err) {
> + dev_err(&pdev->dev, "failed configure watchdog\n");
> + return err;
> + }
> +
> + wdt->wdev.info = &pm8916_wdt_ident,
> + wdt->wdev.ops = &pm8916_wdt_ops,
> + wdt->wdev.parent = &pdev->dev;
> + wdt->wdev.min_timeout = 1;
> + wdt->wdev.max_timeout = 127;
Is this the real range supported by the hardware ?
> + wdt->wdev.timeout = PM8916_WDT_DEFAULT_TIMEOUT;
> + watchdog_set_drvdata(&wdt->wdev, wdt);
> +
> + pm8916_wdt_set_timeout(&wdt->wdev, wdt->wdev.timeout);
> +
Is timeout initialization via fdt not supported on purpose ?
> + return watchdog_register_device(&wdt->wdev);
devm_watchdog_register_device(), or driver removal may result in an
unpleasant surprise.
> +}
> +
> +static const struct of_device_id pm8916_wdt_id_table[] = {
> + { .compatible = "qcom,pm8916-wdt" },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, pm8916_wdt_id_table);
> +
> +static struct platform_driver pm8916_wdt_driver = {
> + .probe = pm8916_wdt_probe,
> + .driver = {
> + .name = "pm8916-wdt",
> + .of_match_table = of_match_ptr(pm8916_wdt_id_table),
> + },
> +};
> +module_platform_driver(pm8916_wdt_driver);
> +
> +MODULE_AUTHOR("Loic Poulain <loic.poulain@linaro.org>");
> +MODULE_DESCRIPTION("Qualcomm pm8916 watchdog driver");
> +MODULE_LICENSE("GPL v2");
> --
> 2.7.4
>
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2018-11-20 7:49 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-11-17 8:28 [PATCH 1/3] watchdog: Add pm8916 watchdog driver Loic Poulain
2018-11-17 8:28 ` [PATCH 2/3] dt-bindings: watchdog: Add Qualcomm PM8916 watchdog Loic Poulain
2018-11-17 8:28 ` [PATCH 3/3] arm64: dts: qcom: pm8916: Add PON watchdog node Loic Poulain
2018-11-19 21:23 ` [PATCH 1/3] watchdog: Add pm8916 watchdog driver Guenter Roeck
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).