From: "dmitry.torokhov@gmail.com" <dmitry.torokhov@gmail.com>
To: Pascal PAILLET-LME <p.paillet@st.com>, lee.jones@linaro.org
Cc: "robh+dt@kernel.org" <robh+dt@kernel.org>,
"mark.rutland@arm.com" <mark.rutland@arm.com>,
"lgirdwood@gmail.com" <lgirdwood@gmail.com>,
"broonie@kernel.org" <broonie@kernel.org>,
"wim@linux-watchdog.org" <wim@linux-watchdog.org>,
"linux@roeck-us.net" <linux@roeck-us.net>,
"linux-input@vger.kernel.org" <linux-input@vger.kernel.org>,
"devicetree@vger.kernel.org" <devicetree@vger.kernel.org>,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
"linux-watchdog@vger.kernel.org" <linux-watchdog@vger.kernel.org>,
"benjamin.gaignard@linaro.org" <benjamin.gaignard@linaro.org>,
"eballetbo@gmail.com" <eballetbo@gmail.com>
Subject: Re: [PATCH v4 6/8] input: stpmic1: add stpmic1 onkey driver
Date: Thu, 18 Oct 2018 11:12:54 -0700 [thread overview]
Message-ID: <20181018181254.GB210757@dtor-ws> (raw)
In-Reply-To: <1539853324-29051-7-git-send-email-p.paillet@st.com>
On Thu, Oct 18, 2018 at 09:02:13AM +0000, Pascal PAILLET-LME wrote:
> From: pascal paillet <p.paillet@st.com>
>
> The stpmic1 pmic is able to manage an onkey button. This driver exposes
> the stpmic1 onkey as an input device. It can also be configured to
> shut-down the power supplies on a long key-press with an adjustable
> duration.
>
> Signed-off-by: pascal paillet <p.paillet@st.com>
OK, so this has dependency on linux/mfd/stpmic1.h and therefore I expect
it will go in through Lee's tree.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
> ---
> changes in v4:
> * remove remove function
> * merge stpmic1_onkey_dt_params() in probe function
> * suppresse struct pmic_onkey_config
> * rename PONKEY_PU_ACTIVE to PONKEY_PU_INACTIVE
>
> drivers/input/misc/Kconfig | 11 +++
> drivers/input/misc/Makefile | 2 +
> drivers/input/misc/stpmic1_onkey.c | 197 +++++++++++++++++++++++++++++++++++++
> 3 files changed, 210 insertions(+)
> create mode 100644 drivers/input/misc/stpmic1_onkey.c
>
> diff --git a/drivers/input/misc/Kconfig b/drivers/input/misc/Kconfig
> index ca59a2b..279fb02 100644
> --- a/drivers/input/misc/Kconfig
> +++ b/drivers/input/misc/Kconfig
> @@ -851,4 +851,15 @@ config INPUT_SC27XX_VIBRA
> To compile this driver as a module, choose M here. The module will
> be called sc27xx_vibra.
>
> +config INPUT_STPMIC1_ONKEY
> + tristate "STPMIC1 PMIC Onkey support"
> + depends on MFD_STPMIC1
> + help
> + Say Y to enable support of onkey embedded into STPMIC1 PMIC. onkey
> + can be used to wakeup from low power modes and force a shut-down on
> + long press.
> +
> + To compile this driver as a module, choose M here: the
> + module will be called stpmic1_onkey.
> +
> endif
> diff --git a/drivers/input/misc/Makefile b/drivers/input/misc/Makefile
> index 9d0f9d1..1b44202 100644
> --- a/drivers/input/misc/Makefile
> +++ b/drivers/input/misc/Makefile
> @@ -71,6 +71,7 @@ obj-$(CONFIG_INPUT_SGI_BTNS) += sgi_btns.o
> obj-$(CONFIG_INPUT_SIRFSOC_ONKEY) += sirfsoc-onkey.o
> obj-$(CONFIG_INPUT_SOC_BUTTON_ARRAY) += soc_button_array.o
> obj-$(CONFIG_INPUT_SPARCSPKR) += sparcspkr.o
> +obj-$(CONFIG_INPUT_STPMIC1_ONKEY) += stpmic1_onkey.o
> obj-$(CONFIG_INPUT_TPS65218_PWRBUTTON) += tps65218-pwrbutton.o
> obj-$(CONFIG_INPUT_TWL4030_PWRBUTTON) += twl4030-pwrbutton.o
> obj-$(CONFIG_INPUT_TWL4030_VIBRA) += twl4030-vibra.o
> @@ -81,3 +82,4 @@ obj-$(CONFIG_INPUT_WM831X_ON) += wm831x-on.o
> obj-$(CONFIG_INPUT_XEN_KBDDEV_FRONTEND) += xen-kbdfront.o
> obj-$(CONFIG_INPUT_YEALINK) += yealink.o
> obj-$(CONFIG_INPUT_IDEAPAD_SLIDEBAR) += ideapad_slidebar.o
> +
> diff --git a/drivers/input/misc/stpmic1_onkey.c b/drivers/input/misc/stpmic1_onkey.c
> new file mode 100644
> index 0000000..6a7f08b
> --- /dev/null
> +++ b/drivers/input/misc/stpmic1_onkey.c
> @@ -0,0 +1,197 @@
> +// SPDX-License-Identifier: GPL-2.0
> +// Copyright (C) STMicroelectronics 2018
> +// Author: Pascal Paillet <p.paillet@st.com> for STMicroelectronics.
> +
> +#include <linux/input.h>
> +#include <linux/interrupt.h>
> +#include <linux/mfd/stpmic1.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/property.h>
> +#include <linux/regmap.h>
> +
> +/**
> + * struct stpmic1_onkey - OnKey data
> + * @input_dev: pointer to input device
> + * @irq_falling: irq that we are hooked on to
> + * @irq_rising: irq that we are hooked on to
> + */
> +struct stpmic1_onkey {
> + struct input_dev *input_dev;
> + int irq_falling;
> + int irq_rising;
> +};
> +
> +static irqreturn_t onkey_falling_irq(int irq, void *ponkey)
> +{
> + struct stpmic1_onkey *onkey = ponkey;
> + struct input_dev *input_dev = onkey->input_dev;
> +
> + input_report_key(input_dev, KEY_POWER, 1);
> + pm_wakeup_event(input_dev->dev.parent, 0);
> + input_sync(input_dev);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static irqreturn_t onkey_rising_irq(int irq, void *ponkey)
> +{
> + struct stpmic1_onkey *onkey = ponkey;
> + struct input_dev *input_dev = onkey->input_dev;
> +
> + input_report_key(input_dev, KEY_POWER, 0);
> + pm_wakeup_event(input_dev->dev.parent, 0);
> + input_sync(input_dev);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int stpmic1_onkey_probe(struct platform_device *pdev)
> +{
> + struct stpmic1 *pmic = dev_get_drvdata(pdev->dev.parent);
> + struct device *dev = &pdev->dev;
> + struct input_dev *input_dev;
> + struct stpmic1_onkey *onkey;
> + unsigned int val, reg = 0;
> + int error;
> +
> + onkey = devm_kzalloc(dev, sizeof(*onkey), GFP_KERNEL);
> + if (!onkey)
> + return -ENOMEM;
> +
> + onkey->irq_falling = platform_get_irq_byname(pdev, "onkey-falling");
> + if (onkey->irq_falling < 0) {
> + dev_err(dev, "failed: request IRQ onkey-falling %d\n",
> + onkey->irq_falling);
> + return onkey->irq_falling;
> + }
> +
> + onkey->irq_rising = platform_get_irq_byname(pdev, "onkey-rising");
> + if (onkey->irq_rising < 0) {
> + dev_err(dev, "failed: request IRQ onkey-rising %d\n",
> + onkey->irq_rising);
> + return onkey->irq_rising;
> + }
> +
> + if (!device_property_read_u32(dev, "power-off-time-sec", &val)) {
> + if ((val > 0) && (val <= 16)) {
> + dev_dbg(dev, "power-off-time=%d seconds\n", val);
> + reg |= PONKEY_PWR_OFF;
> + reg |= ((16 - val) & PONKEY_TURNOFF_TIMER_MASK);
> + } else {
> + dev_err(dev, "power-off-time-sec out of range\n");
> + return -EINVAL;
> + }
> + }
> +
> + if (device_property_present(dev, "st,onkey-clear-cc-flag"))
> + reg |= PONKEY_CC_FLAG_CLEAR;
> +
> + error = regmap_update_bits(pmic->regmap, PKEY_TURNOFF_CR,
> + PONKEY_TURNOFF_MASK, reg);
> + if (error) {
> + dev_err(dev, "PKEY_TURNOFF_CR write failed: %d\n", error);
> + return error;
> + }
> +
> + if (device_property_present(dev, "st,onkey-pu-inactive")) {
> + error = regmap_update_bits(pmic->regmap, PADS_PULL_CR,
> + PONKEY_PU_INACTIVE,
> + PONKEY_PU_INACTIVE);
> + if (error) {
> + dev_err(dev, "ONKEY Pads configuration failed: %d\n", error);
> + return error;
> + }
> + }
> +
> + input_dev = devm_input_allocate_device(dev);
> + if (!input_dev) {
> + dev_err(dev, "Can't allocate Pwr Onkey Input Device\n");
> + return -ENOMEM;
> + }
> +
> + input_dev->name = "pmic_onkey";
> + input_dev->phys = "pmic_onkey/input0";
> +
> + input_set_capability(input_dev, EV_KEY, KEY_POWER);
> +
> + onkey->input_dev = input_dev;
> +
> + /* interrupt is nested in a thread */
> + error = devm_request_threaded_irq(dev, onkey->irq_falling, NULL,
> + onkey_falling_irq, IRQF_ONESHOT,
> + dev_name(dev), onkey);
> + if (error) {
> + dev_err(dev, "Can't get IRQ Onkey Falling: %d\n", error);
> + return error;
> + }
> +
> + error = devm_request_threaded_irq(dev, onkey->irq_rising, NULL,
> + onkey_rising_irq, IRQF_ONESHOT,
> + dev_name(dev), onkey);
> + if (error) {
> + dev_err(dev, "Can't get IRQ Onkey Rising: %d\n", error);
> + return error;
> + }
> +
> + error = input_register_device(input_dev);
> + if (error) {
> + dev_err(dev, "Can't register power button: %d\n", error);
> + return error;
> + }
> +
> + platform_set_drvdata(pdev, onkey);
> + device_init_wakeup(dev, true);
> +
> + return 0;
> +}
> +
> +static int __maybe_unused stpmic1_onkey_suspend(struct device *dev)
> +{
> + struct platform_device *pdev = to_platform_device(dev);
> + struct stpmic1_onkey *onkey = platform_get_drvdata(pdev);
> +
> + if (device_may_wakeup(dev)) {
> + enable_irq_wake(onkey->irq_falling);
> + enable_irq_wake(onkey->irq_rising);
> + }
> + return 0;
> +}
> +
> +static int __maybe_unused stpmic1_onkey_resume(struct device *dev)
> +{
> + struct platform_device *pdev = to_platform_device(dev);
> + struct stpmic1_onkey *onkey = platform_get_drvdata(pdev);
> +
> + if (device_may_wakeup(dev)) {
> + disable_irq_wake(onkey->irq_falling);
> + disable_irq_wake(onkey->irq_rising);
> + }
> + return 0;
> +}
> +
> +static SIMPLE_DEV_PM_OPS(stpmic1_onkey_pm,
> + stpmic1_onkey_suspend,
> + stpmic1_onkey_resume);
> +
> +static const struct of_device_id of_stpmic1_onkey_match[] = {
> + { .compatible = "st,stpmic1-onkey" },
> + { },
> +};
> +
> +MODULE_DEVICE_TABLE(of, of_stpmic1_onkey_match);
> +
> +static struct platform_driver stpmic1_onkey_driver = {
> + .probe = stpmic1_onkey_probe,
> + .driver = {
> + .name = "stpmic1_onkey",
> + .of_match_table = of_match_ptr(of_stpmic1_onkey_match),
> + .pm = &stpmic1_onkey_pm,
> + },
> +};
> +module_platform_driver(stpmic1_onkey_driver);
> +
> +MODULE_DESCRIPTION("Onkey driver for STPMIC1");
> +MODULE_AUTHOR("Pascal Paillet <p.paillet@st.com>");
> +MODULE_LICENSE("GPL v2");
> --
> 1.9.1
--
Dmitry
next prev parent reply other threads:[~2018-10-19 2:15 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-10-18 9:02 [PATCH v4 0/8] Introduce STPMIC1 PMIC Driver Pascal PAILLET-LME
2018-10-18 9:02 ` [PATCH v4 2/8] mfd: stpmic1: add stpmic1 driver Pascal PAILLET-LME
2018-10-25 11:21 ` Lee Jones
2018-10-25 12:40 ` Benjamin Gaignard
2018-10-26 7:17 ` Lee Jones
2018-10-18 9:02 ` [PATCH v4 1/8] dt-bindings: mfd: document stpmic1 Pascal PAILLET-LME
2018-10-18 18:47 ` Rob Herring
2018-10-25 9:44 ` Lee Jones
2018-10-25 12:57 ` Rob Herring
2018-10-26 6:46 ` Lee Jones
2018-10-26 9:48 ` Pascal PAILLET-LME
2018-10-26 11:46 ` Lee Jones
2018-10-18 9:02 ` [PATCH v4 3/8] dt-bindings: regulator: document stpmic1 pmic regulators Pascal PAILLET-LME
2018-10-18 9:02 ` [PATCH v4 4/8] regulator: stpmic1: add stpmic1 regulator driver Pascal PAILLET-LME
2018-10-19 11:50 ` Mark Brown
2018-10-24 12:54 ` Pascal PAILLET-LME
2018-10-24 13:17 ` Mark Brown
2018-10-25 13:23 ` Pascal PAILLET-LME
2018-10-26 20:33 ` Mark Brown
2018-10-18 9:02 ` [PATCH v4 6/8] input: stpmic1: add stpmic1 onkey driver Pascal PAILLET-LME
2018-10-18 18:12 ` dmitry.torokhov [this message]
2018-10-18 9:02 ` [PATCH v4 7/8] dt-bindings: watchdog: document stpmic1 pmic watchdog Pascal PAILLET-LME
2018-10-18 9:02 ` [PATCH v4 5/8] dt-bindings: input: document stpmic1 pmic onkey Pascal PAILLET-LME
2018-10-18 9:02 ` [PATCH v4 8/8] watchdog: stpmic1: add stpmic1 watchdog driver Pascal PAILLET-LME
2018-10-18 13:34 ` Guenter Roeck
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181018181254.GB210757@dtor-ws \
--to=dmitry.torokhov@gmail.com \
--cc=benjamin.gaignard@linaro.org \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=eballetbo@gmail.com \
--cc=lee.jones@linaro.org \
--cc=lgirdwood@gmail.com \
--cc=linux-input@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-watchdog@vger.kernel.org \
--cc=linux@roeck-us.net \
--cc=mark.rutland@arm.com \
--cc=p.paillet@st.com \
--cc=robh+dt@kernel.org \
--cc=wim@linux-watchdog.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).