Linux-Watchdog Archive on lore.kernel.org
 help / color / Atom feed
From: Guenter Roeck <linux@roeck-us.net>
To: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Cc: bjorn.andersson@linaro.org, wim@linux-watchdog.org,
	agross@kernel.org, linux-arm-msm@vger.kernel.org,
	linux-watchdog@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH 1/2] watchdog: qcom: support pre-timeout when the bark irq is available
Date: Tue, 10 Sep 2019 11:06:55 -0700
Message-ID: <20190910180655.GA25286@roeck-us.net> (raw)
In-Reply-To: <20190906205411.31666-2-jorge.ramirez-ortiz@linaro.org>

On Fri, Sep 06, 2019 at 10:54:10PM +0200, Jorge Ramirez-Ortiz wrote:
> Use the bark interrupt as the pre-timeout notifier whenever this
> interrupt is available.
> 
> By default, the pretimeout notification shall occur one second earlier
> than the timeout.
> 
> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>

Nitpick below, otherwise:

Reviewed-by: Guenter Roeck <linux@roeck-us.net>

> ---
>  drivers/watchdog/qcom-wdt.c | 70 ++++++++++++++++++++++++++++++++++---
>  1 file changed, 65 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/watchdog/qcom-wdt.c b/drivers/watchdog/qcom-wdt.c
> index 7be7f87be28f..935c78a882a3 100644
> --- a/drivers/watchdog/qcom-wdt.c
> +++ b/drivers/watchdog/qcom-wdt.c
> @@ -1,8 +1,10 @@
>  // SPDX-License-Identifier: GPL-2.0-only
>  /* Copyright (c) 2014, The Linux Foundation. All rights reserved.
>   */
> +#include <linux/bits.h>
>  #include <linux/clk.h>
>  #include <linux/delay.h>
> +#include <linux/interrupt.h>
>  #include <linux/io.h>
>  #include <linux/kernel.h>
>  #include <linux/module.h>
> @@ -19,6 +21,9 @@ enum wdt_reg {
>  	WDT_BITE_TIME,
>  };
>  
> +#define QCOM_WDT_ENABLE		BIT(0)
> +#define QCOM_WDT_ENABLE_IRQ	BIT(1)
> +
>  static const u32 reg_offset_data_apcs_tmr[] = {
>  	[WDT_RST] = 0x38,
>  	[WDT_EN] = 0x40,
> @@ -54,15 +59,35 @@ struct qcom_wdt *to_qcom_wdt(struct watchdog_device *wdd)
>  	return container_of(wdd, struct qcom_wdt, wdd);
>  }
>  
> +static inline int qcom_get_enable(struct watchdog_device *wdd)
> +{
> +	int enable = QCOM_WDT_ENABLE;
> +
> +	if (wdd->pretimeout)
> +		enable |= QCOM_WDT_ENABLE_IRQ;
> +
> +	return enable;
> +}
> +
> +static irqreturn_t qcom_wdt_isr(int irq, void *arg)
> +{
> +	struct watchdog_device *wdd = arg;
> +
> +	watchdog_notify_pretimeout(wdd);
> +
> +	return IRQ_HANDLED;
> +}
> +
>  static int qcom_wdt_start(struct watchdog_device *wdd)
>  {
>  	struct qcom_wdt *wdt = to_qcom_wdt(wdd);
> +	unsigned int bark = wdd->timeout - wdd->pretimeout;
>  
>  	writel(0, wdt_addr(wdt, WDT_EN));
>  	writel(1, wdt_addr(wdt, WDT_RST));
> -	writel(wdd->timeout * wdt->rate, wdt_addr(wdt, WDT_BARK_TIME));
> +	writel(bark * wdt->rate, wdt_addr(wdt, WDT_BARK_TIME));
>  	writel(wdd->timeout * wdt->rate, wdt_addr(wdt, WDT_BITE_TIME));
> -	writel(1, wdt_addr(wdt, WDT_EN));
> +	writel(qcom_get_enable(wdd), wdt_addr(wdt, WDT_EN));
>  	return 0;
>  }
>  
> @@ -89,6 +114,13 @@ static int qcom_wdt_set_timeout(struct watchdog_device *wdd,
>  	return qcom_wdt_start(wdd);
>  }
>  
> +static int qcom_wdt_set_pretimeout(struct watchdog_device *wdd,
> +				   unsigned int timeout)
> +{
> +	wdd->pretimeout = timeout;
> +	return qcom_wdt_start(wdd);
> +}
> +
>  static int qcom_wdt_restart(struct watchdog_device *wdd, unsigned long action,
>  			    void *data)
>  {
> @@ -105,7 +137,7 @@ static int qcom_wdt_restart(struct watchdog_device *wdd, unsigned long action,
>  	writel(1, wdt_addr(wdt, WDT_RST));
>  	writel(timeout, wdt_addr(wdt, WDT_BARK_TIME));
>  	writel(timeout, wdt_addr(wdt, WDT_BITE_TIME));
> -	writel(1, wdt_addr(wdt, WDT_EN));
> +	writel(QCOM_WDT_ENABLE, wdt_addr(wdt, WDT_EN));
>  
>  	/*
>  	 * Actually make sure the above sequence hits hardware before sleeping.
> @@ -121,6 +153,7 @@ static const struct watchdog_ops qcom_wdt_ops = {
>  	.stop		= qcom_wdt_stop,
>  	.ping		= qcom_wdt_ping,
>  	.set_timeout	= qcom_wdt_set_timeout,
> +	.set_pretimeout	= qcom_wdt_set_pretimeout,
>  	.restart        = qcom_wdt_restart,
>  	.owner		= THIS_MODULE,
>  };
> @@ -133,6 +166,15 @@ static const struct watchdog_info qcom_wdt_info = {
>  	.identity	= KBUILD_MODNAME,
>  };
>  
> +static const struct watchdog_info qcom_wdt_pt_info = {
> +	.options	= WDIOF_KEEPALIVEPING
> +			| WDIOF_MAGICCLOSE
> +			| WDIOF_SETTIMEOUT
> +			| WDIOF_PRETIMEOUT
> +			| WDIOF_CARDRESET,
> +	.identity	= KBUILD_MODNAME,
> +};
> +
>  static void qcom_clk_disable_unprepare(void *data)
>  {
>  	clk_disable_unprepare(data);
> @@ -146,7 +188,7 @@ static int qcom_wdt_probe(struct platform_device *pdev)
>  	struct device_node *np = dev->of_node;
>  	const u32 *regs;
>  	u32 percpu_offset;
> -	int ret;
> +	int irq, ret;
>  
>  	regs = of_device_get_match_data(dev);
>  	if (!regs) {
> @@ -204,7 +246,25 @@ static int qcom_wdt_probe(struct platform_device *pdev)
>  		return -EINVAL;
>  	}
>  
> -	wdt->wdd.info = &qcom_wdt_info;
> +	/* check if there is pretimeout support */
> +	irq = platform_get_irq(pdev, 0);
> +	if (irq > 0) {
> +		ret = devm_request_irq(dev, irq, qcom_wdt_isr,
> +				       IRQF_TRIGGER_RISING,
> +				       "wdt_bark", &wdt->wdd);
> +		if (ret)
> +			return ret;
> +
> +		wdt->wdd.info = &qcom_wdt_pt_info;
> +		wdt->wdd.pretimeout = 1;
> +	} else {
> +		if (irq == -EPROBE_DEFER)
> +			return -EPROBE_DEFER;
> +
> +		wdt->wdd.info = &qcom_wdt_info;
> +		wdt->wdd.pretimeout = 0;

It is not necessary to set pretimeout to 0; the data structure was
allocated with devm_kzalloc(). The compiler won't know that and
generate unnecessary code otherwise.

> +	}
> +
>  	wdt->wdd.ops = &qcom_wdt_ops;
>  	wdt->wdd.min_timeout = 1;
>  	wdt->wdd.max_timeout = 0x10000000U / wdt->rate;

  reply index

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-09-06 20:54 [PATCH 0/2] qcom_wdt bark irq support Jorge Ramirez-Ortiz
2019-09-06 20:54 ` [PATCH 1/2] watchdog: qcom: support pre-timeout when the bark irq is available Jorge Ramirez-Ortiz
2019-09-10 18:06   ` Guenter Roeck [this message]
2019-09-12  7:24     ` Jorge Ramirez-Ortiz, Linaro
2019-09-12 18:34       ` Guenter Roeck
2019-09-06 20:54 ` [PATCH 2/2] watchdog: qcom: remove unnecessary variable from private storage Jorge Ramirez-Ortiz
2019-09-10 18:08   ` Guenter Roeck

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190910180655.GA25286@roeck-us.net \
    --to=linux@roeck-us.net \
    --cc=agross@kernel.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=jorge.ramirez-ortiz@linaro.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-watchdog@vger.kernel.org \
    --cc=wim@linux-watchdog.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-Watchdog Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-watchdog/0 linux-watchdog/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-watchdog linux-watchdog/ https://lore.kernel.org/linux-watchdog \
		linux-watchdog@vger.kernel.org linux-watchdog@archiver.kernel.org
	public-inbox-index linux-watchdog


Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-watchdog


AGPL code for this site: git clone https://public-inbox.org/ public-inbox