From: Sean Anderson <sean.anderson@seco.com>
To: "David S . Miller" <davem@davemloft.net>,
Jakub Kicinski <kuba@kernel.org>,
Madalin Bucur <madalin.bucur@nxp.com>,
Camelia Alexandra Groza <camelia.groza@nxp.com>,
netdev@vger.kernel.org
Cc: devicetree@vger.kernel.org, Li Yang <leoyang.li@nxp.com>,
Sean Anderson <sean.anderson@seco.com>,
linux-kernel@vger.kernel.org,
Russell King <linux@armlinux.org.uk>,
Eric Dumazet <edumazet@google.com>,
Rob Herring <robh+dt@kernel.org>,
Paul Mackerras <paulus@samba.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Shawn Guo <shawnguo@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
"linuxppc-dev @ lists . ozlabs . org"
<linuxppc-dev@lists.ozlabs.org>,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH net-next v5 0/9] [RFT] net: dpaa: Convert to phylink
Date: Mon, 26 Sep 2022 15:03:12 -0400 [thread overview]
Message-ID: <20220926190322.2889342-1-sean.anderson@seco.com> (raw)
This series converts the DPAA driver to phylink.
I have tried to maintain backwards compatibility with existing device
trees whereever possible. However, one area where I was unable to
achieve this was with QSGMII. Please refer to patch 2 for details.
All mac drivers have now been converted. I would greatly appreciate if
anyone has T-series or P-series boards they can test/debug this series
on. I only have an LS1046ARDB. Everything but QSGMII should work without
breakage; QSGMII needs patches 7 and 8. For this reason, the last 4
patches in this series should be applied together (and should not go
through separate trees).
This series depends on [1] and [2].
[1] https://lore.kernel.org/netdev/20220725153730.2604096-1-sean.anderson@seco.com/
[2] https://lore.kernel.org/netdev/20220725151039.2581576-1-sean.anderson@seco.com/
Changes in v5:
- Add Lynx PCS binding
Changes in v4:
- Use pcs-handle-names instead of pcs-names, as discussed
- Don't fail if phy support was not compiled in
- Split off rate adaptation series
- Split off DPAA "preparation" series
- Split off Lynx 10G support
- t208x: Mark MAC1 and MAC2 as 10G
- Add XFI PCS for t208x MAC1/MAC2
Changes in v3:
- Expand pcs-handle to an array
- Add vendor prefix 'fsl,' to rgmii and mii properties.
- Set maxItems for pcs-names
- Remove phy-* properties from example because dt-schema complains and I
can't be bothered to figure out how to make it work.
- Add pcs-handle as a preferred version of pcsphy-handle
- Deprecate pcsphy-handle
- Remove mii/rmii properties
- Put the PCS mdiodev only after we are done with it (since the PCS
does not perform a get itself).
- Remove _return label from memac_initialization in favor of returning
directly
- Fix grabbing the default PCS not checking for -ENODATA from
of_property_match_string
- Set DTSEC_ECNTRL_R100M in dtsec_link_up instead of dtsec_mac_config
- Remove rmii/mii properties
- Replace 1000Base... with 1000BASE... to match IEEE capitalization
- Add compatibles for QSGMII PCSs
- Split arm and powerpcs dts updates
Changes in v2:
- Better document how we select which PCS to use in the default case
- Move PCS_LYNX dependency to fman Kconfig
- Remove unused variable slow_10g_if
- Restrict valid link modes based on the phy interface. This is easier
to set up, and mostly captures what I intended to do the first time.
We now have a custom validate which restricts half-duplex for some SoCs
for RGMII, but generally just uses the default phylink validate.
- Configure the SerDes in enable/disable
- Properly implement all ethtool ops and ioctls. These were mostly
stubbed out just enough to compile last time.
- Convert 10GEC and dTSEC as well
- Fix capitalization of mEMAC in commit messages
- Add nodes for QSGMII PCSs
- Add nodes for QSGMII PCSs
Sean Anderson (9):
dt-bindings: net: Expand pcs-handle to an array
dt-bindings: net: Add Lynx PCS binding
dt-bindings: net: fman: Add additional interface properties
net: fman: memac: Add serdes support
net: fman: memac: Use lynx pcs driver
net: dpaa: Convert to phylink
powerpc: dts: t208x: Mark MAC1 and MAC2 as 10G
powerpc: dts: qoriq: Add nodes for QSGMII PCSs
arm64: dts: layerscape: Add nodes for QSGMII PCSs
.../bindings/net/dsa/renesas,rzn1-a5psw.yaml | 1 +
.../bindings/net/ethernet-controller.yaml | 10 +-
.../bindings/net/fsl,fman-dtsec.yaml | 53 +-
.../bindings/net/fsl,qoriq-mc-dpmac.yaml | 2 +-
.../devicetree/bindings/net/fsl-fman.txt | 5 +-
.../bindings/net/pcs/fsl,lynx-pcs.yaml | 40 +
.../boot/dts/freescale/fsl-ls1043-post.dtsi | 24 +
.../boot/dts/freescale/fsl-ls1046-post.dtsi | 25 +
.../fsl/qoriq-fman3-0-10g-0-best-effort.dtsi | 3 +-
.../boot/dts/fsl/qoriq-fman3-0-10g-0.dtsi | 10 +-
.../fsl/qoriq-fman3-0-10g-1-best-effort.dtsi | 10 +-
.../boot/dts/fsl/qoriq-fman3-0-10g-1.dtsi | 10 +-
.../boot/dts/fsl/qoriq-fman3-0-10g-2.dtsi | 45 ++
.../boot/dts/fsl/qoriq-fman3-0-10g-3.dtsi | 45 ++
.../boot/dts/fsl/qoriq-fman3-0-1g-0.dtsi | 3 +-
.../boot/dts/fsl/qoriq-fman3-0-1g-1.dtsi | 10 +-
.../boot/dts/fsl/qoriq-fman3-0-1g-2.dtsi | 10 +-
.../boot/dts/fsl/qoriq-fman3-0-1g-3.dtsi | 10 +-
.../boot/dts/fsl/qoriq-fman3-0-1g-4.dtsi | 3 +-
.../boot/dts/fsl/qoriq-fman3-0-1g-5.dtsi | 10 +-
.../boot/dts/fsl/qoriq-fman3-1-10g-0.dtsi | 10 +-
.../boot/dts/fsl/qoriq-fman3-1-10g-1.dtsi | 10 +-
.../boot/dts/fsl/qoriq-fman3-1-1g-0.dtsi | 3 +-
.../boot/dts/fsl/qoriq-fman3-1-1g-1.dtsi | 10 +-
.../boot/dts/fsl/qoriq-fman3-1-1g-2.dtsi | 10 +-
.../boot/dts/fsl/qoriq-fman3-1-1g-3.dtsi | 10 +-
.../boot/dts/fsl/qoriq-fman3-1-1g-4.dtsi | 3 +-
.../boot/dts/fsl/qoriq-fman3-1-1g-5.dtsi | 10 +-
arch/powerpc/boot/dts/fsl/t2081si-post.dtsi | 4 +-
drivers/net/ethernet/freescale/dpaa/Kconfig | 4 +-
.../net/ethernet/freescale/dpaa/dpaa_eth.c | 89 +--
.../ethernet/freescale/dpaa/dpaa_ethtool.c | 90 +--
drivers/net/ethernet/freescale/fman/Kconfig | 4 +-
.../net/ethernet/freescale/fman/fman_dtsec.c | 459 +++++------
.../net/ethernet/freescale/fman/fman_mac.h | 10 -
.../net/ethernet/freescale/fman/fman_memac.c | 746 +++++++++---------
.../net/ethernet/freescale/fman/fman_tgec.c | 131 ++-
drivers/net/ethernet/freescale/fman/mac.c | 168 +---
drivers/net/ethernet/freescale/fman/mac.h | 23 +-
39 files changed, 1073 insertions(+), 1050 deletions(-)
create mode 100644 Documentation/devicetree/bindings/net/pcs/fsl,lynx-pcs.yaml
create mode 100644 arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-2.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-3.dtsi
--
2.35.1.1320.gc452695387.dirty
next reply other threads:[~2022-09-26 19:04 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-09-26 19:03 Sean Anderson [this message]
2022-09-26 19:03 ` [PATCH net-next v5 1/9] dt-bindings: net: Expand pcs-handle to an array Sean Anderson
2022-09-27 14:39 ` Rob Herring
2022-09-27 15:33 ` Rob Herring
2022-09-27 16:27 ` Sean Anderson
2022-09-26 19:03 ` [PATCH net-next v5 2/9] dt-bindings: net: Add Lynx PCS binding Sean Anderson
2022-09-30 14:37 ` Rob Herring
2022-09-26 19:03 ` [PATCH net-next v5 3/9] dt-bindings: net: fman: Add additional interface properties Sean Anderson
2022-09-26 19:03 ` [PATCH net-next v5 4/9] net: fman: memac: Add serdes support Sean Anderson
2022-09-26 19:03 ` [PATCH net-next v5 5/9] net: fman: memac: Use lynx pcs driver Sean Anderson
2022-09-26 19:03 ` [PATCH net-next v5 6/9] net: dpaa: Convert to phylink Sean Anderson
2022-09-26 19:03 ` [PATCH net-next v5 7/9] powerpc: dts: t208x: Mark MAC1 and MAC2 as 10G Sean Anderson
2022-09-26 19:03 ` [PATCH net-next v5 8/9] powerpc: dts: qoriq: Add nodes for QSGMII PCSs Sean Anderson
2022-09-26 19:03 ` [PATCH net-next v5 9/9] arm64: dts: layerscape: " Sean Anderson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220926190322.2889342-1-sean.anderson@seco.com \
--to=sean.anderson@seco.com \
--cc=camelia.groza@nxp.com \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=edumazet@google.com \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=kuba@kernel.org \
--cc=leoyang.li@nxp.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=linuxppc-dev@lists.ozlabs.org \
--cc=madalin.bucur@nxp.com \
--cc=netdev@vger.kernel.org \
--cc=pabeni@redhat.com \
--cc=paulus@samba.org \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).