From: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
To: Rasmus Villemoes <linux@rasmusvillemoes.dk>,
Alessandro Zummo <a.zummo@towertech.it>,
Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>,
devicetree@vger.kernel.org, Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Conor Dooley <conor+dt@kernel.org>,
linux-rtc@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH v2 3/8] dt-bindings: rtc: isl12022: add bindings for battery alarm trip levels
Date: Tue, 13 Jun 2023 21:09:02 +0200 [thread overview]
Message-ID: <0600a505-d1bf-f4be-57ef-51d34c77501e@linaro.org> (raw)
In-Reply-To: <20230613130011.305589-4-linux@rasmusvillemoes.dk>
On 13/06/2023 15:00, Rasmus Villemoes wrote:
> The isl12022 has a built-in support for monitoring the voltage of the
> backup battery, and setting bits in the status register when that
> voltage drops below two predetermined levels (usually 85% and 75% of
> the nominal voltage). However, since it can operate at wide range of
> battery voltages (2.5V - 5.5V), one must configure those trip levels
> according to which battery is used on a given board.
>
> Add bindings for defining these two trip levels. While the register
> and bit names suggest that they should correspond to 85% and 75% of
> the nominal battery voltage, the data sheet also says
>
> There are total of 7 levels that could be selected for the first
> alarm. Any of the of levels could be selected as the first alarm
> with no reference as to nominal Battery voltage level.
>
> Hence this provides the hardware designer the ability to choose values
> based on the discharge characteristics of the battery chosen for the
> given product, rather than just having one battery-microvolt property
> and having the driver choose levels close to 0.85/0.75 times that.
>
> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
> ---
> .../devicetree/bindings/rtc/intersil,isl12022.yaml | 14 ++++++++++++++
> 1 file changed, 14 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/rtc/intersil,isl12022.yaml b/Documentation/devicetree/bindings/rtc/intersil,isl12022.yaml
> index 7c1e638d657a..d5d3a687a34d 100644
> --- a/Documentation/devicetree/bindings/rtc/intersil,isl12022.yaml
> +++ b/Documentation/devicetree/bindings/rtc/intersil,isl12022.yaml
> @@ -22,6 +22,18 @@ properties:
> interrupts:
> maxItems: 1
>
> + isil,trip-level85-microvolt:
Why encoding level85 in the property name? Your commit msg (datasheet)
suggests this is quite flexible, so why it cannot be just list of two
trip levels - for first and second interrupt?
> + description: |
Do not need '|' unless you need to preserve formatting.
Best regards,
Krzysztof
next prev parent reply other threads:[~2023-06-13 19:09 UTC|newest]
Thread overview: 78+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-06-12 11:30 [PATCH 0/8] rtc: isl12022: battery backup voltage and clock support Rasmus Villemoes
2023-06-12 11:30 ` [PATCH 1/8] rtc: isl12022: remove wrong warning for low battery level Rasmus Villemoes
2023-06-12 11:30 ` [PATCH 2/8] dt-bindings: rtc: Move isil,isl12022 from trivial-rtc.yaml into own schema file Rasmus Villemoes
2023-06-12 12:26 ` Rob Herring
2023-06-12 12:36 ` Rasmus Villemoes
2023-06-12 13:54 ` Alexandre Belloni
2023-06-12 14:20 ` Rob Herring
2023-06-13 8:13 ` Rasmus Villemoes
2023-06-12 11:30 ` [PATCH 3/8] dt-bindings: rtc: isl12022: add bindings for battery alarm trip levels Rasmus Villemoes
2023-06-12 11:30 ` [PATCH 4/8] rtc: isl12022: add support for trip level DT bindings Rasmus Villemoes
2023-06-12 15:44 ` Andy Shevchenko
2023-06-12 18:10 ` kernel test robot
2023-06-12 18:58 ` kernel test robot
2023-06-12 11:30 ` [PATCH 5/8] rtc: isl12022: implement RTC_VL_READ and RTC_VL_CLR ioctls Rasmus Villemoes
2023-06-12 14:07 ` Alexandre Belloni
2023-06-13 7:27 ` Rasmus Villemoes
2023-06-12 15:48 ` Andy Shevchenko
2023-06-12 16:10 ` Alexandre Belloni
2023-06-13 7:53 ` Rasmus Villemoes
2023-06-13 9:00 ` Alexandre Belloni
2023-06-12 11:30 ` [PATCH 6/8] rtc: isl12022: trigger battery level detection during probe Rasmus Villemoes
2023-06-12 12:30 ` Rasmus Villemoes
2023-06-12 14:17 ` Alexandre Belloni
2023-06-13 7:51 ` Rasmus Villemoes
2023-06-12 14:15 ` Alexandre Belloni
2023-06-13 7:44 ` Rasmus Villemoes
2023-06-13 8:58 ` Alexandre Belloni
2023-06-12 11:30 ` [PATCH 7/8] dt-bindings: rtc: isl12022: add #clock-cells property Rasmus Villemoes
2023-06-13 7:41 ` Krzysztof Kozlowski
2023-06-12 11:30 ` [PATCH 8/8] rtc: isl12022: implement support for the #clock-cells DT property Rasmus Villemoes
2023-06-13 13:00 ` [PATCH v2 0/8] rtc: isl12022: battery backup voltage and clock support Rasmus Villemoes
2023-06-13 13:00 ` [PATCH v2 1/8] rtc: isl12022: remove wrong warning for low battery level Rasmus Villemoes
2023-06-13 13:00 ` [PATCH v2 2/8] dt-bindings: rtc: Move isil,isl12022 from trivial-rtc.yaml into own schema file Rasmus Villemoes
2023-06-13 19:06 ` Krzysztof Kozlowski
2023-06-13 13:00 ` [PATCH v2 3/8] dt-bindings: rtc: isl12022: add bindings for battery alarm trip levels Rasmus Villemoes
2023-06-13 19:09 ` Krzysztof Kozlowski [this message]
2023-06-13 19:51 ` Rasmus Villemoes
2023-06-13 21:37 ` Krzysztof Kozlowski
2023-06-13 13:00 ` [PATCH v2 4/8] rtc: isl12022: add support for trip level DT bindings Rasmus Villemoes
2023-06-13 13:00 ` [PATCH v2 5/8] rtc: isl12022: implement RTC_VL_READ ioctl Rasmus Villemoes
2023-06-13 15:20 ` Andy Shevchenko
2023-06-13 21:26 ` Alexandre Belloni
2023-06-14 12:16 ` Andy Shevchenko
2023-06-14 13:50 ` Alexandre Belloni
2023-06-14 15:13 ` Andy Shevchenko
2023-06-15 10:53 ` Rasmus Villemoes
2023-06-15 10:58 ` Andy Shevchenko
2023-06-13 13:00 ` [PATCH v2 6/8] rtc: isl12022: trigger battery level detection during probe Rasmus Villemoes
2023-06-13 13:00 ` [PATCH v2 7/8] dt-bindings: rtc: isl12022: add #clock-cells property Rasmus Villemoes
2023-06-13 19:10 ` Krzysztof Kozlowski
2023-06-13 20:25 ` Rasmus Villemoes
2023-06-13 21:38 ` Krzysztof Kozlowski
2023-06-13 13:00 ` [PATCH v2 8/8] rtc: isl12022: implement support for the #clock-cells DT property Rasmus Villemoes
2023-06-13 15:25 ` Andy Shevchenko
2023-06-14 10:51 ` Rasmus Villemoes
2023-06-14 12:13 ` Andy Shevchenko
2023-06-13 19:10 ` kernel test robot
2023-06-14 5:27 ` kernel test robot
2023-06-13 15:26 ` [PATCH v2 0/8] rtc: isl12022: battery backup voltage and clock support Andy Shevchenko
2023-06-13 19:06 ` Krzysztof Kozlowski
2023-06-15 11:03 ` Rasmus Villemoes
2023-06-15 10:58 ` [PATCH v3 " Rasmus Villemoes
2023-06-15 10:58 ` [PATCH v3 1/8] rtc: isl12022: remove wrong warning for low battery level Rasmus Villemoes
2023-06-15 10:58 ` [PATCH v3 2/8] dt-bindings: rtc: Move isil,isl12022 from trivial-rtc.yaml into own schema file Rasmus Villemoes
2023-06-15 10:58 ` [PATCH v3 3/8] dt-bindings: rtc: isl12022: add bindings for battery alarm trip levels Rasmus Villemoes
2023-06-17 8:12 ` Krzysztof Kozlowski
2023-06-15 10:58 ` [PATCH v3 4/8] rtc: isl12022: add support for trip level DT binding Rasmus Villemoes
2023-06-15 11:11 ` Andy Shevchenko
2023-06-19 7:27 ` Rasmus Villemoes
2023-06-15 10:58 ` [PATCH v3 5/8] rtc: isl12022: implement RTC_VL_READ ioctl Rasmus Villemoes
2023-06-15 10:58 ` [PATCH v3 6/8] rtc: isl12022: trigger battery level detection during probe Rasmus Villemoes
2023-06-15 10:58 ` [PATCH v3 7/8] dt-bindings: rtc: isl12022: add #clock-cells property Rasmus Villemoes
2023-06-17 8:13 ` Krzysztof Kozlowski
2023-06-15 10:58 ` [PATCH v3 8/8] rtc: isl12022: implement support for the #clock-cells DT property Rasmus Villemoes
2023-07-28 14:31 ` [PATCH v3 0/8] rtc: isl12022: battery backup voltage and clock support Rasmus Villemoes
2023-08-03 6:45 ` Rasmus Villemoes
2023-08-09 12:28 ` Rasmus Villemoes
2023-08-15 23:28 ` Alexandre Belloni
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=0600a505-d1bf-f4be-57ef-51d34c77501e@linaro.org \
--to=krzysztof.kozlowski@linaro.org \
--cc=a.zummo@towertech.it \
--cc=alexandre.belloni@bootlin.com \
--cc=andriy.shevchenko@linux.intel.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-rtc@vger.kernel.org \
--cc=linux@rasmusvillemoes.dk \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).