* RE: Promise TX4 100: neither IDE port enabled
@ 2003-04-04 15:07 Jonathan Vardy
2003-04-04 23:58 ` Thomas Backlund
2003-04-05 13:31 ` Adam Johansson
0 siblings, 2 replies; 7+ messages in thread
From: Jonathan Vardy @ 2003-04-04 15:07 UTC (permalink / raw)
To: Adam Johansson; +Cc: linux-kernel
> Without knowing the cause or fix for it I instead run ac-patches.
> The card(s) are than configured correctly.
> I now run 2.4.21pre5ac3 and I remember 2.4.21pre4ac4 also worked fine.
I tried 2.4.21-pre5-ac3 but still I get the same problems, with what
settings did you compile the kernel?
I used these:
On: PROMISE PDC202{46|62|65|67} support
On: Special UDMA Feature
On: PROMISE PDC202{68|69|70|71|75|76|77} support
Off: Special FastTrak Feature
Off: Support for IDE Raid controllers (EXPERIMENTAL)
Yours sincerey, Jonathan Vardy
^ permalink raw reply [flat|nested] 7+ messages in thread
* RE: Promise TX4 100: neither IDE port enabled
2003-04-04 15:07 Promise TX4 100: neither IDE port enabled Jonathan Vardy
@ 2003-04-04 23:58 ` Thomas Backlund
2003-04-05 13:31 ` Adam Johansson
1 sibling, 0 replies; 7+ messages in thread
From: Thomas Backlund @ 2003-04-04 23:58 UTC (permalink / raw)
To: linux-kernel
Jonathan Vardy wrote:
>> Without knowing the cause or fix for it I instead run ac-patches.
>> The card(s) are than configured correctly.
>> I now run 2.4.21pre5ac3 and I remember 2.4.21pre4ac4 also worked fine.
>
> I tried 2.4.21-pre5-ac3 but still I get the same problems, with what
> settings did you compile the kernel?
>
> I used these:
>
> On: PROMISE PDC202{46|62|65|67} support
> On: Special UDMA Feature
> On: PROMISE PDC202{68|69|70|71|75|76|77} support
>
> Off: Special FastTrak Feature
Switch this on and it should work ...
Thomas
^ permalink raw reply [flat|nested] 7+ messages in thread
* RE: Promise TX4 100: neither IDE port enabled
2003-04-04 15:07 Promise TX4 100: neither IDE port enabled Jonathan Vardy
2003-04-04 23:58 ` Thomas Backlund
@ 2003-04-05 13:31 ` Adam Johansson
1 sibling, 0 replies; 7+ messages in thread
From: Adam Johansson @ 2003-04-05 13:31 UTC (permalink / raw)
To: Jonathan Vardy; +Cc: linux-kernel
On Fri, 2003-04-04 at 17:07, Jonathan Vardy wrote:
> > Without knowing the cause or fix for it I instead run ac-patches.
> > The card(s) are than configured correctly.
> > I now run 2.4.21pre5ac3 and I remember 2.4.21pre4ac4 also worked fine.
>
> I tried 2.4.21-pre5-ac3 but still I get the same problems, with what
> settings did you compile the kernel?
>
> I used these:
>
> On: PROMISE PDC202{46|62|65|67} support
> On: Special UDMA Feature
> On: PROMISE PDC202{68|69|70|71|75|76|77} support
>
> Off: Special FastTrak Feature
> Off: Support for IDE Raid controllers (EXPERIMENTAL)
I do have Special FastTrak feature turned on as well.
I have also compiled support for IDE Raid + Promise RAID.
dmesg shows the drives at hde and hdg detected as UDMA(100).
ataraid/d0: ataraid/d0p1
Drive 0 is 43979 Mb (33 / 0)
Drive 1 is 43979 Mb (34 / 0)
Still I simply treat it as a Ultra-card and use /dev/hde and /dev/hdg in
a RAID1 config with 2 IBM 45Gb drives.
(though /dev/ataraid/d0p1 exists, something I wasn't aware I had choosen
to compile into the kernel )
"cat /proc/ide/pdc202xx" says both masters are running UDMA4 and that
the card is an Ultra100.
hdparm -tT /dev/md5 gives;
Timing buffer-cache reads: 128 Mb in 0.29 seconds =441.38 MB/sec
Timing buffered disk reads: 64 Mb in 1.77 seconds = 36.16 MB/sec
Good luck!
/Adam Johansson
> Yours sincerey, Jonathan Vardy
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: Promise TX4 100: neither IDE port enabled
2003-04-04 10:56 Jonathan Vardy
2003-04-04 12:39 ` Adam Johansson
@ 2003-04-05 0:03 ` Jonathan Vardy
1 sibling, 0 replies; 7+ messages in thread
From: Jonathan Vardy @ 2003-04-05 0:03 UTC (permalink / raw)
To: linux-kernel
After many different kernels, here are my experiences so far:
The original red hat 9.0 2.4.20 kernel correctly identifies the drives on
the promise as UDMA(100).
The 2.4.21-pre7, 2.4.21-pre6, 2.4.21-pre5-ac3 do not detect the promise
correctly giving the following error:
ide: Assuming 33MHz system bus speed for PIO modes; override
with idebus=xx
PIIX4: IDE controller at PCI slot 00:04.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:pio
PDC20270: IDE controller at PCI slot 02:01.0
PDC20270: chipset revision 2
PDC20270: not 100% native mode: will probe irqs later
PDC20270: neither IDE port enabled (BIOS)
PDC20270: neither IDE port enabled (BIOS)
We compiled a version of 2.4.20 without modules but then it would detect all
the drives on the promise as UDMA(33)
Does anybody have know if the problem is in the kernel version or settings?
Yours sincerely, Jonathan Vardy
>I've rebooted using the orignal Red Hat kernel (2.4.20) and it
>recongnizes the Promise card. Here are the details:
>
>ide: Assuming 33MHz system bus speed for PIO modes; override with
>idebus=xx
>PIIX4: IDE controller at PCI slot 00:04.1
>PIIX4: chipset revision 1
>PIIX4: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
> ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:pio
>PDC20270: IDE controller at PCI slot 02:01.0
>PDC20270: chipset revision 2
>PDC20270: not 100% native mode: will probe irqs later
> ide2: BM-DMA at 0x9040-0x9047, BIOS settings: hde:pio, hdf:pio
> ide3: BM-DMA at 0x9048-0x904f, BIOS settings: hdg:pio, hdh:pio
> ide4: BM-DMA at 0x90c0-0x90c7, BIOS settings: hdi:pio, hdj:pio
> ide5: BM-DMA at 0x90c8-0x90cf, BIOS settings: hdk:pio, hdl:pio
>hda: Maxtor 2B020H1, ATA DISK drive
>blk: queue c0453420, I/O limit 4095Mb (mask 0xffffffff)
>hdc: WDC WD1200BB-00CAA1, ATA DISK drive
>blk: queue c04538a0, I/O limit 4095Mb (mask 0xffffffff)
>hde: WDC WD1200BB-60CJA1, ATA DISK drive
>blk: queue c0453d20, I/O limit 4095Mb (mask 0xffffffff)
>hdg: WDC WD1200BB-60CJA1, ATA DISK drive
>blk: queue c04541a0, I/O limit 4095Mb (mask 0xffffffff)
>hdi: WDC WD1200BB-60CJA1, ATA DISK drive
>blk: queue c0454620, I/O limit 4095Mb (mask 0xffffffff)
>hdk: WDC WD1200BB-60CJA1, ATA DISK drive
>blk: queue c0454aa0, I/O limit 4095Mb (mask 0xffffffff)
>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
>ide1 at 0x170-0x177,0x376 on irq 15
>ide2 at 0x9000-0x9007,0x9012 on irq 19
>ide3 at 0x9020-0x9027,0x9032 on irq 19
>ide4 at 0x9080-0x9087,0x9092 on irq 19
i>de5 at 0x90a0-0x90a7,0x90b2 on irq 19
>hda: host protected area => 1
>hda: 39062500 sectors (20000 MB) w/2048KiB Cache, CHS=2431/255/63,
>UDMA(33)
>hdc: host protected area => 1
>hdc: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
>UDMA(33)
>hde: host protected area => 1
>hde: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
>UDMA(100)
>hdg: host protected area => 1
>hdg: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
>UDMA(100)
>hdi: host protected area => 1
>hdi: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
>UDMA(100)
>hdk: host protected area => 1
>hdk: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
>UDMA(100)
^ permalink raw reply [flat|nested] 7+ messages in thread
* RE: Promise TX4 100: neither IDE port enabled
2003-04-04 10:56 Jonathan Vardy
@ 2003-04-04 12:39 ` Adam Johansson
2003-04-05 0:03 ` Jonathan Vardy
1 sibling, 0 replies; 7+ messages in thread
From: Adam Johansson @ 2003-04-04 12:39 UTC (permalink / raw)
To: Jonathan Vardy; +Cc: linux-kernel
Hi, I can confirm with my experiences with both Ultra and Fasttrak under
recent 2.4.20+ kernels fail detecting more than UDMA33 on these cards.
Without knowing the cause or fix for it I instead run ac-patches.
The card(s) are than configured correctly.
I now run 2.4.21pre5ac3 and I remember 2.4.21pre4ac4 also worked fine.
Cheers!
Adam Johansson
On Fri, 2003-04-04 at 12:56, Jonathan Vardy wrote:
> I've rebooted using the orignal Red Hat kernel (2.4.20) and it
> recongnizes the Promise card. Here are the details:
>
> ide: Assuming 33MHz system bus speed for PIO modes; override with
> idebus=xx
> PIIX4: IDE controller at PCI slot 00:04.1
> PIIX4: chipset revision 1
> PIIX4: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
> ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:pio
> PDC20270: IDE controller at PCI slot 02:01.0
> PDC20270: chipset revision 2
> PDC20270: not 100% native mode: will probe irqs later
> ide2: BM-DMA at 0x9040-0x9047, BIOS settings: hde:pio, hdf:pio
> ide3: BM-DMA at 0x9048-0x904f, BIOS settings: hdg:pio, hdh:pio
> ide4: BM-DMA at 0x90c0-0x90c7, BIOS settings: hdi:pio, hdj:pio
> ide5: BM-DMA at 0x90c8-0x90cf, BIOS settings: hdk:pio, hdl:pio
> hda: Maxtor 2B020H1, ATA DISK drive
> blk: queue c0453420, I/O limit 4095Mb (mask 0xffffffff)
> hdc: WDC WD1200BB-00CAA1, ATA DISK drive
> blk: queue c04538a0, I/O limit 4095Mb (mask 0xffffffff)
> hde: WDC WD1200BB-60CJA1, ATA DISK drive
> blk: queue c0453d20, I/O limit 4095Mb (mask 0xffffffff)
> hdg: WDC WD1200BB-60CJA1, ATA DISK drive
> blk: queue c04541a0, I/O limit 4095Mb (mask 0xffffffff)
> hdi: WDC WD1200BB-60CJA1, ATA DISK drive
> blk: queue c0454620, I/O limit 4095Mb (mask 0xffffffff)
> hdk: WDC WD1200BB-60CJA1, ATA DISK drive
> blk: queue c0454aa0, I/O limit 4095Mb (mask 0xffffffff)
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> ide1 at 0x170-0x177,0x376 on irq 15
> ide2 at 0x9000-0x9007,0x9012 on irq 19
> ide3 at 0x9020-0x9027,0x9032 on irq 19
> ide4 at 0x9080-0x9087,0x9092 on irq 19
> ide5 at 0x90a0-0x90a7,0x90b2 on irq 19
> hda: host protected area => 1
> hda: 39062500 sectors (20000 MB) w/2048KiB Cache, CHS=2431/255/63,
> UDMA(33)
> hdc: host protected area => 1
> hdc: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
> UDMA(33)
> hde: host protected area => 1
> hde: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
> UDMA(100)
> hdg: host protected area => 1
> hdg: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
> UDMA(100)
> hdi: host protected area => 1
> hdi: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
> UDMA(100)
> hdk: host protected area => 1
> hdk: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
> UDMA(100)
>
>
> Better results but doen anybody know why 2.4.21pre6 can't detect it
> right?
>
> >
> > ide: Assuming 33MHz system bus speed for PIO modes; override
> > with idebus=xx
> > PIIX4: IDE controller at PCI slot 00:04.1
> > PIIX4: chipset revision 1
> > PIIX4: not 100% native mode: will probe irqs later
> > ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
> > ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:pio
> > PDC20270: IDE controller at PCI slot 02:01.0
> > PDC20270: chipset revision 2
> > PDC20270: not 100% native mode: will probe irqs later
> > PDC20270: neither IDE port enabled (BIOS)
> > PDC20270: neither IDE port enabled (BIOS)
> > hda: Maxtor 2B020H1, ATA DISK drive
> > blk: queue c0395860, I/O limit 4095Mb (mask 0xffffffff)
> > hdc: WDC WD1200BB-00CAA1, ATA DISK drive
> > blk: queue c0395cd0, I/O limit 4095Mb (mask 0xffffffff)
> > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> > ide1 at 0x170-0x177,0x376 on irq 15
> > hda: host protected area => 1
> > hda: 39062500 sectors (20000 MB) w/2048KiB Cache,
> > CHS=2431/255/63, UDMA(33)
> > hdc: host protected area => 1
> > hdc: 234441648 sectors (120034 MB) w/2048KiB Cache,
> > CHS=232581/16/63, UDMA(33)
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
^ permalink raw reply [flat|nested] 7+ messages in thread
* RE: Promise TX4 100: neither IDE port enabled
@ 2003-04-04 10:56 Jonathan Vardy
2003-04-04 12:39 ` Adam Johansson
2003-04-05 0:03 ` Jonathan Vardy
0 siblings, 2 replies; 7+ messages in thread
From: Jonathan Vardy @ 2003-04-04 10:56 UTC (permalink / raw)
To: Jonathan Vardy, linux-kernel
I've rebooted using the orignal Red Hat kernel (2.4.20) and it
recongnizes the Promise card. Here are the details:
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
PIIX4: IDE controller at PCI slot 00:04.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:pio
PDC20270: IDE controller at PCI slot 02:01.0
PDC20270: chipset revision 2
PDC20270: not 100% native mode: will probe irqs later
ide2: BM-DMA at 0x9040-0x9047, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0x9048-0x904f, BIOS settings: hdg:pio, hdh:pio
ide4: BM-DMA at 0x90c0-0x90c7, BIOS settings: hdi:pio, hdj:pio
ide5: BM-DMA at 0x90c8-0x90cf, BIOS settings: hdk:pio, hdl:pio
hda: Maxtor 2B020H1, ATA DISK drive
blk: queue c0453420, I/O limit 4095Mb (mask 0xffffffff)
hdc: WDC WD1200BB-00CAA1, ATA DISK drive
blk: queue c04538a0, I/O limit 4095Mb (mask 0xffffffff)
hde: WDC WD1200BB-60CJA1, ATA DISK drive
blk: queue c0453d20, I/O limit 4095Mb (mask 0xffffffff)
hdg: WDC WD1200BB-60CJA1, ATA DISK drive
blk: queue c04541a0, I/O limit 4095Mb (mask 0xffffffff)
hdi: WDC WD1200BB-60CJA1, ATA DISK drive
blk: queue c0454620, I/O limit 4095Mb (mask 0xffffffff)
hdk: WDC WD1200BB-60CJA1, ATA DISK drive
blk: queue c0454aa0, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0x9000-0x9007,0x9012 on irq 19
ide3 at 0x9020-0x9027,0x9032 on irq 19
ide4 at 0x9080-0x9087,0x9092 on irq 19
ide5 at 0x90a0-0x90a7,0x90b2 on irq 19
hda: host protected area => 1
hda: 39062500 sectors (20000 MB) w/2048KiB Cache, CHS=2431/255/63,
UDMA(33)
hdc: host protected area => 1
hdc: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
UDMA(33)
hde: host protected area => 1
hde: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
UDMA(100)
hdg: host protected area => 1
hdg: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
UDMA(100)
hdi: host protected area => 1
hdi: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
UDMA(100)
hdk: host protected area => 1
hdk: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
UDMA(100)
Better results but doen anybody know why 2.4.21pre6 can't detect it
right?
>
> ide: Assuming 33MHz system bus speed for PIO modes; override
> with idebus=xx
> PIIX4: IDE controller at PCI slot 00:04.1
> PIIX4: chipset revision 1
> PIIX4: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
> ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:pio
> PDC20270: IDE controller at PCI slot 02:01.0
> PDC20270: chipset revision 2
> PDC20270: not 100% native mode: will probe irqs later
> PDC20270: neither IDE port enabled (BIOS)
> PDC20270: neither IDE port enabled (BIOS)
> hda: Maxtor 2B020H1, ATA DISK drive
> blk: queue c0395860, I/O limit 4095Mb (mask 0xffffffff)
> hdc: WDC WD1200BB-00CAA1, ATA DISK drive
> blk: queue c0395cd0, I/O limit 4095Mb (mask 0xffffffff)
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> ide1 at 0x170-0x177,0x376 on irq 15
> hda: host protected area => 1
> hda: 39062500 sectors (20000 MB) w/2048KiB Cache,
> CHS=2431/255/63, UDMA(33)
> hdc: host protected area => 1
> hdc: 234441648 sectors (120034 MB) w/2048KiB Cache,
> CHS=232581/16/63, UDMA(33)
^ permalink raw reply [flat|nested] 7+ messages in thread
* Promise TX4 100: neither IDE port enabled
@ 2003-04-04 9:10 Jonathan Vardy
0 siblings, 0 replies; 7+ messages in thread
From: Jonathan Vardy @ 2003-04-04 9:10 UTC (permalink / raw)
To: linux-kernel
Hi,
I am having trouble getting my promise fasttrak TX4 running with Red
Hat. I am using kerner 2.4.21-pre6 compiled with
PROMISE PDC202{46|62|65|67} support
Special UDMA Feature
PROMISE PDC202{68|69|70|71|75|76|77} support
But without Special FastTrak Feature and Support for IDE Raid
controllers (EXPERIMENTAL)
While booting I get the following results:
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
PIIX4: IDE controller at PCI slot 00:04.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:pio
PDC20270: IDE controller at PCI slot 02:01.0
PDC20270: chipset revision 2
PDC20270: not 100% native mode: will probe irqs later
PDC20270: neither IDE port enabled (BIOS)
PDC20270: neither IDE port enabled (BIOS)
hda: Maxtor 2B020H1, ATA DISK drive
blk: queue c0395860, I/O limit 4095Mb (mask 0xffffffff)
hdc: WDC WD1200BB-00CAA1, ATA DISK drive
blk: queue c0395cd0, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: host protected area => 1
hda: 39062500 sectors (20000 MB) w/2048KiB Cache, CHS=2431/255/63,
UDMA(33)
hdc: host protected area => 1
hdc: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
UDMA(33)
As you can see the Promise card is not functioning at all. Doen anyone
have any ideas why it is not functioning?
Thanks, Jonathan Vardy
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2003-04-05 13:20 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2003-04-04 15:07 Promise TX4 100: neither IDE port enabled Jonathan Vardy
2003-04-04 23:58 ` Thomas Backlund
2003-04-05 13:31 ` Adam Johansson
-- strict thread matches above, loose matches on Subject: below --
2003-04-04 10:56 Jonathan Vardy
2003-04-04 12:39 ` Adam Johansson
2003-04-05 0:03 ` Jonathan Vardy
2003-04-04 9:10 Jonathan Vardy
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).