From: Huang Ying <ying.huang@intel.com>
To: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>,
linux-pm@vger.kernel.org, linux-pci@vger.kernel.org,
kexec@lists.infradead.org, linux-kernel@vger.kernel.org,
"Rafael J. Wysocki" <rjw@sisk.pl>
Subject: Re: [RFC 1/3] PCI/PM: Fix kexec for D3cold and bridge suspending
Date: Thu, 20 Sep 2012 16:19:33 +0800 [thread overview]
Message-ID: <1348129173.8212.218.camel@yhuang-dev> (raw)
In-Reply-To: <877grpywhy.fsf@xmission.com>
On Thu, 2012-09-20 at 00:38 -0700, Eric W. Biederman wrote:
> Bjorn Helgaas <bhelgaas@google.com> writes:
>
> > +cc Eric and kexec list
> >
> > On Mon, Sep 17, 2012 at 2:54 AM, Huang Ying <ying.huang@intel.com> wrote:
> >> If PCI devices are put into D3cold before kexec, because the
> >> configuration registers of PCI devices in D3cold are not accessible.
> >>
> >> And if PCI bridges are put into low power state before kexec,
> >> configuration registers of PCI devices underneath the PCI bridges are
> >> not accessible too.
> >>
> >> These will make some PCI devices can not be scanned after kexec, so
> >> resume the PCI devices in D3cold or PCI bridges in low power state
> >> before kexec.
> >
> > Don't we need to resume the device even without the kexec issue? And
> > even if it's in D1 or D2?
>
> The basic requirement is that the device needs to be visible so we can
> auto discover it. As I recall most sleep states don't make the device
> invisible and we can handle the rest in the device initializatoin code.
PCI devices in D3cold or under a bridge in D3hot will not be visible, so
we must fix that for kexec to run properly.
> > It looks to me like pci_msi_shutdown() (and probably drv->shutdown())
> > depend on the device being in D0.
>
> There is certainly a depenency on the config registers being visible.
> Although I don't know if much will go wrong if they aren't.
>
> Ceratinly pci_msi_shutdown doesn't have anything to do if the device has
> had so much power removed that the device is not even exectuing.
Don't know which power state device should be in for pci_msi_shutdown
etc. But it appears that normal shutdown/reboot and kexec works at most
times so far. D3cold and bridge in D3hot works for normal
shutdown/reboot, but not for kexec. So I write some fix.
Best Regards,
Huang Ying
> >> Signed-off-by: Huang Ying <ying.huang@intel.com>
> >> ---
> >> drivers/pci/pci-driver.c | 4 ++++
> >> 1 file changed, 4 insertions(+)
> >>
> >> --- a/drivers/pci/pci-driver.c
> >> +++ b/drivers/pci/pci-driver.c
> >> @@ -421,6 +421,10 @@ static void pci_device_shutdown(struct d
> >> struct pci_dev *pci_dev = to_pci_dev(dev);
> >> struct pci_driver *drv = pci_dev->driver;
> >>
> >> + /* Resume bridges and devices in D3cold for kexec to work properly */
> >> + if (pci_dev->current_state == PCI_D3cold || pci_dev->subordinate)
> >> + pm_runtime_resume(dev);
> >> +
> >> if (drv && drv->shutdown)
> >> drv->shutdown(pci_dev);
> >> pci_msi_shutdown(pci_dev);
> >
> > _______________________________________________
> > kexec mailing list
> > kexec@lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/kexec
next prev parent reply other threads:[~2012-09-20 8:19 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-09-17 8:54 [RFC 0/3] PCI/PM: RTD3 fixes/changes for 3.7 Huang Ying
2012-09-17 8:54 ` [RFC 1/3] PCI/PM: Fix kexec for D3cold and bridge suspending Huang Ying
2012-09-17 20:54 ` Bjorn Helgaas
2012-09-20 7:38 ` Eric W. Biederman
2012-09-20 8:19 ` Huang Ying [this message]
2012-09-20 8:27 ` Eric W. Biederman
2012-09-20 19:20 ` Rafael J. Wysocki
2012-09-21 0:28 ` Huang Ying
2012-09-21 19:30 ` Rafael J. Wysocki
2012-09-17 8:54 ` [RFC 2/3] PCI/PM: Make PCI devices notified when its power resource turned on Huang Ying
2012-09-20 19:33 ` Rafael J. Wysocki
2012-09-17 8:54 ` [RFC 3/3] PCI/PM: Disable PME poll for PCIe devices Huang Ying
2012-09-20 19:31 ` Rafael J. Wysocki
2012-09-20 19:39 ` Matthew Garrett
2012-09-21 1:50 ` Huang Ying
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1348129173.8212.218.camel@yhuang-dev \
--to=ying.huang@intel.com \
--cc=bhelgaas@google.com \
--cc=ebiederm@xmission.com \
--cc=kexec@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=rjw@sisk.pl \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).