* [PATCH 0/5] Support new Exynos4415 SoC based on Cortex-A9 quad cores
@ 2014-10-20 3:29 Chanwoo Choi
2014-10-20 3:32 ` [PATCH 1/5] ARM: EXYNOS: Add EXYNOS4415 SoC ID Chanwoo Choi
` (4 more replies)
0 siblings, 5 replies; 21+ messages in thread
From: Chanwoo Choi @ 2014-10-20 3:29 UTC (permalink / raw)
To: linux-samsung-soc, linux-kernel, linux-arm-kernel
Cc: kgene.kim, ben-linux, linux, mark.rutland, arnd, olof,
tomasz.figa, mturquette, thomas.abraham, linus.walleij,
sw0312.kim, kyungmin.park, inki.dae, geunsik.lim, jh80.chung,
cw00.choi, jaewon02.kim, ideal.song, yj44.cho
This patchset support new Exynos4415 Samsung SoC based on Cortex-A9 quad cores.
Exynos4415 is a System-On-Chip (SoC) that is based on 32-bit RISC processor
for Smartphone. It is desigend with the 28nm low-power high-K metal gate process
and provides the best performance features.
This patchset include some patches such as:
- Support booting of Exynos4415
- Supoort uart/mct/adc/gic/i2c/spi/power-domain/pmu/mshc/ehci/ohci/pwm/amba
- Support the clock controller for Exynos4415 using common clk framework
- Support the gpio control for Exynos4415 using pinctrl subsystem
Chanwoo Choi (4):
ARM: EXYNOS: Add EXYNOS4415 SoC ID
clk: samsung: exynos4415: Add clocks using common clock framework
clk: samsung: Document binding for Exynos4415 clock controller
ARM: dts: Add dts files for Exynos4415 SoC
Tomasz Figa (1):
pinctrl: exynos: Add support for Exynos4415
.../devicetree/bindings/clock/exynos4415-clock.txt | 49 +
arch/arm/boot/dts/exynos4415-pinctrl.dtsi | 613 +++++++++++
arch/arm/boot/dts/exynos4415.dtsi | 627 +++++++++++
arch/arm/mach-exynos/Kconfig | 5 +
arch/arm/mach-exynos/common.h | 8 +
arch/arm/mach-exynos/exynos.c | 2 +
drivers/clk/samsung/Makefile | 1 +
drivers/clk/samsung/clk-exynos4415.c | 1133 ++++++++++++++++++++
drivers/pinctrl/samsung/pinctrl-exynos.c | 78 ++
drivers/pinctrl/samsung/pinctrl-samsung.c | 2 +
drivers/pinctrl/samsung/pinctrl-samsung.h | 1 +
include/dt-bindings/clock/exynos4415.h | 360 +++++++
12 files changed, 2879 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/exynos4415-clock.txt
create mode 100644 arch/arm/boot/dts/exynos4415-pinctrl.dtsi
create mode 100644 arch/arm/boot/dts/exynos4415.dtsi
create mode 100644 drivers/clk/samsung/clk-exynos4415.c
create mode 100644 include/dt-bindings/clock/exynos4415.h
--
1.8.0
^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH 1/5] ARM: EXYNOS: Add EXYNOS4415 SoC ID
2014-10-20 3:29 [PATCH 0/5] Support new Exynos4415 SoC based on Cortex-A9 quad cores Chanwoo Choi
@ 2014-10-20 3:32 ` Chanwoo Choi
2014-10-24 11:43 ` Tomasz Figa
2014-10-20 3:32 ` [PATCH 2/5] clk: samsung: exynos4415: Add clocks using common clock framework Chanwoo Choi
` (3 subsequent siblings)
4 siblings, 1 reply; 21+ messages in thread
From: Chanwoo Choi @ 2014-10-20 3:32 UTC (permalink / raw)
To: linux-samsung-soc, linux-kernel, linux-arm-kernel
Cc: kgene.kim, ben-linux, linux, mark.rutland, arnd, olof,
tomasz.figa, mturquette, thomas.abraham, linus.walleij,
sw0312.kim, kyungmin.park, inki.dae, geunsik.lim, jh80.chung,
cw00.choi, jaewon02.kim, ideal.song, yj44.cho
This patch add Exynos4415's SoC ID. Exynos4415 is based on the 32-bit RISC
processor for Smartphone. Exynos4415 uses Cortex A9 quad-cores and has a target
speed of 1.6GHz and provides 8.5GB/s memory bandwidth.
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
---
arch/arm/mach-exynos/Kconfig | 5 +++++
arch/arm/mach-exynos/common.h | 8 ++++++++
arch/arm/mach-exynos/exynos.c | 2 ++
3 files changed, 15 insertions(+)
diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig
index 46f3c0d..349c867 100644
--- a/arch/arm/mach-exynos/Kconfig
+++ b/arch/arm/mach-exynos/Kconfig
@@ -75,6 +75,11 @@ config SOC_EXYNOS4412
default y
depends on ARCH_EXYNOS4
+config SOC_EXYNOS4415
+ bool "SAMSUNG EXYNOS4415"
+ default y
+ depends on ARCH_EXYNOS4
+
config SOC_EXYNOS5250
bool "SAMSUNG EXYNOS5250"
default y
diff --git a/arch/arm/mach-exynos/common.h b/arch/arm/mach-exynos/common.h
index d4d09bc..ffc0c22 100644
--- a/arch/arm/mach-exynos/common.h
+++ b/arch/arm/mach-exynos/common.h
@@ -21,6 +21,7 @@
#define EXYNOS4210_CPU_ID 0x43210000
#define EXYNOS4212_CPU_ID 0x43220000
#define EXYNOS4412_CPU_ID 0xE4412200
+#define EXYNOS4415_CPU_ID 0xE4415000
#define EXYNOS4_CPU_MASK 0xFFFE0000
#define EXYNOS5250_SOC_ID 0x43520000
@@ -42,6 +43,7 @@ IS_SAMSUNG_CPU(exynos3250, EXYNOS3250_SOC_ID, EXYNOS3_SOC_MASK)
IS_SAMSUNG_CPU(exynos4210, EXYNOS4210_CPU_ID, EXYNOS4_CPU_MASK)
IS_SAMSUNG_CPU(exynos4212, EXYNOS4212_CPU_ID, EXYNOS4_CPU_MASK)
IS_SAMSUNG_CPU(exynos4412, EXYNOS4412_CPU_ID, EXYNOS4_CPU_MASK)
+IS_SAMSUNG_CPU(exynos4415, EXYNOS4415_CPU_ID, EXYNOS4_CPU_MASK)
IS_SAMSUNG_CPU(exynos5250, EXYNOS5250_SOC_ID, EXYNOS5_SOC_MASK)
IS_SAMSUNG_CPU(exynos5410, EXYNOS5410_SOC_ID, EXYNOS5_SOC_MASK)
IS_SAMSUNG_CPU(exynos5420, EXYNOS5420_SOC_ID, EXYNOS5_SOC_MASK)
@@ -72,6 +74,12 @@ IS_SAMSUNG_CPU(exynos5800, EXYNOS5800_SOC_ID, EXYNOS5_SOC_MASK)
# define soc_is_exynos4412() 0
#endif
+#if defined(CONFIG_SOC_EXYNOS4415)
+# define soc_is_exynos4415() is_samsung_exynos4415()
+#else
+# define soc_is_exynos4415() 0
+#endif
+
#define EXYNOS4210_REV_0 (0x0)
#define EXYNOS4210_REV_1_0 (0x10)
#define EXYNOS4210_REV_1_1 (0x11)
diff --git a/arch/arm/mach-exynos/exynos.c b/arch/arm/mach-exynos/exynos.c
index 2f2f7b2..52bca8e 100644
--- a/arch/arm/mach-exynos/exynos.c
+++ b/arch/arm/mach-exynos/exynos.c
@@ -253,6 +253,7 @@ static const struct of_device_id exynos_dt_pmu_match[] = {
{ .compatible = "samsung,exynos4210-pmu" },
{ .compatible = "samsung,exynos4212-pmu" },
{ .compatible = "samsung,exynos4412-pmu" },
+ { .compatible = "samsung,exynos4415-pmu" },
{ .compatible = "samsung,exynos5250-pmu" },
{ .compatible = "samsung,exynos5260-pmu" },
{ .compatible = "samsung,exynos5410-pmu" },
@@ -337,6 +338,7 @@ static char const *exynos_dt_compat[] __initconst = {
"samsung,exynos4210",
"samsung,exynos4212",
"samsung,exynos4412",
+ "samsung,exynos4415",
"samsung,exynos5",
"samsung,exynos5250",
"samsung,exynos5260",
--
1.8.0
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH 2/5] clk: samsung: exynos4415: Add clocks using common clock framework
2014-10-20 3:29 [PATCH 0/5] Support new Exynos4415 SoC based on Cortex-A9 quad cores Chanwoo Choi
2014-10-20 3:32 ` [PATCH 1/5] ARM: EXYNOS: Add EXYNOS4415 SoC ID Chanwoo Choi
@ 2014-10-20 3:32 ` Chanwoo Choi
2014-10-24 10:54 ` Sylwester Nawrocki
2014-10-24 13:18 ` Daniel Drake
2014-10-20 3:32 ` [PATCH 3/5] clk: samsung: Document binding for Exynos4415 clock controller Chanwoo Choi
` (2 subsequent siblings)
4 siblings, 2 replies; 21+ messages in thread
From: Chanwoo Choi @ 2014-10-20 3:32 UTC (permalink / raw)
To: linux-samsung-soc, linux-kernel, linux-arm-kernel
Cc: kgene.kim, ben-linux, linux, mark.rutland, arnd, olof,
tomasz.figa, mturquette, thomas.abraham, linus.walleij,
sw0312.kim, kyungmin.park, inki.dae, geunsik.lim, jh80.chung,
cw00.choi, jaewon02.kim, ideal.song, yj44.cho,
Sylwester Nawrocki
This patch adds the new clock driver of Exynos4415 SoC based on Cortex-A9
using common clock framework. The CMU (Clock Management Unit) of Exynos4415
controls PLLs(Phase Locked Loops) and generates system clocks for CPU, buses
and function clocks for individual IPs.
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
---
drivers/clk/samsung/Makefile | 1 +
drivers/clk/samsung/clk-exynos4415.c | 1133 ++++++++++++++++++++++++++++++++
include/dt-bindings/clock/exynos4415.h | 360 ++++++++++
3 files changed, 1494 insertions(+)
create mode 100644 drivers/clk/samsung/clk-exynos4415.c
create mode 100644 include/dt-bindings/clock/exynos4415.h
diff --git a/drivers/clk/samsung/Makefile b/drivers/clk/samsung/Makefile
index 6fb4bc6..d8535e6 100644
--- a/drivers/clk/samsung/Makefile
+++ b/drivers/clk/samsung/Makefile
@@ -5,6 +5,7 @@
obj-$(CONFIG_COMMON_CLK) += clk.o clk-pll.o
obj-$(CONFIG_SOC_EXYNOS3250) += clk-exynos3250.o
obj-$(CONFIG_ARCH_EXYNOS4) += clk-exynos4.o
+obj-$(CONFIG_SOC_EXYNOS4415) += clk-exynos4415.o
obj-$(CONFIG_SOC_EXYNOS5250) += clk-exynos5250.o
obj-$(CONFIG_SOC_EXYNOS5260) += clk-exynos5260.o
obj-$(CONFIG_SOC_EXYNOS5410) += clk-exynos5410.o
diff --git a/drivers/clk/samsung/clk-exynos4415.c b/drivers/clk/samsung/clk-exynos4415.c
new file mode 100644
index 0000000..a4b6211
--- /dev/null
+++ b/drivers/clk/samsung/clk-exynos4415.c
@@ -0,0 +1,1133 @@
+/*
+ * Copyright (c) 2014 Samsung Electronics Co., Ltd.
+ * Author: Chanwoo Choi <cw00.choi@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Common Clock Framework support for Exynos4415 SoC.
+ */
+
+#include <linux/clk.h>
+#include <linux/clkdev.h>
+#include <linux/clk-provider.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/syscore_ops.h>
+
+#include <dt-bindings/clock/exynos4415.h>
+
+#include "clk.h"
+#include "clk-pll.h"
+
+#define SRC_LEFTBUS 0x4200
+#define DIV_LEFTBUS 0x4500
+#define GATE_IP_LEFTBUS 0x4800
+#define GATE_IP_IMAGE 0x4930
+#define SRC_RIGHTBUS 0x8200
+#define DIV_RIGHTBUS 0x8500
+#define GATE_IP_RIGHTBUS 0x8800
+#define GATE_IP_PERIR 0x8960
+#define EPLL_LOCK 0xc010
+#define G3D_PLL_LOCK 0xc020
+#define DISP_PLL_LOCK 0xc030
+#define ISP_PLL_LOCK 0xc040
+#define EPLL_CON0 0xc110
+#define EPLL_CON1 0xc114
+#define EPLL_CON2 0xc118
+#define G3D_PLL_CON0 0xc120
+#define G3D_PLL_CON1 0xc124
+#define G3D_PLL_CON2 0xc128
+#define ISP_PLL_CON0 0xc130
+#define ISP_PLL_CON1 0xc134
+#define ISP_PLL_CON2 0xc138
+#define DISP_PLL_CON0 0xc140
+#define DISP_PLL_CON1 0xc144
+#define DISP_PLL_CON2 0xc148
+#define SRC_TOP0 0xc210
+#define SRC_TOP1 0xc214
+#define SRC_CAM 0xc220
+#define SRC_TV 0xc224
+#define SRC_MFC 0xc228
+#define SRC_G3D 0xc22c
+#define SRC_LCD 0xc234
+#define SRC_ISP 0xc238
+#define SRC_MAUDIO 0xc23c
+#define SRC_FSYS 0xc240
+#define SRC_PERIL0 0xc250
+#define SRC_PERIL1 0xc254
+#define SRC_CAM1 0xc258
+#define SRC_TOP_ISP0 0xc25c
+#define SRC_TOP_ISP1 0xc260
+#define SRC_MASK_TOP 0xc310
+#define SRC_MASK_CAM 0xc320
+#define SRC_MASK_TV 0xc324
+#define SRC_MASK_LCD 0xc334
+#define SRC_MASK_ISP 0xc338
+#define SRC_MASK_MAUDIO 0xc33c
+#define SRC_MASK_FSYS 0xc340
+#define SRC_MASK_PERIL0 0xc350
+#define SRC_MASK_PERIL1 0xc354
+#define DIV_TOP 0xc510
+#define DIV_CAM 0xc520
+#define DIV_TV 0xc524
+#define DIV_MFC 0xc528
+#define DIV_G3D 0xc52c
+#define DIV_LCD 0xc534
+#define DIV_ISP 0xc538
+#define DIV_MAUDIO 0xc53c
+#define DIV_FSYS0 0xc540
+#define DIV_FSYS1 0xc544
+#define DIV_FSYS2 0xc548
+#define DIV_PERIL0 0xc550
+#define DIV_PERIL1 0xc554
+#define DIV_PERIL2 0xc558
+#define DIV_PERIL3 0xc55c
+#define DIV_PERIL4 0xc560
+#define DIV_PERIL5 0xc564
+#define DIV_CAM1 0xc568
+#define DIV_TOP_ISP1 0xc56c
+#define DIV_TOP_ISP0 0xc570
+#define CLKDIV2_RATIO 0xc580
+#define GATE_SCLK_CAM 0xc820
+#define GATE_SCLK_TV 0xc824
+#define GATE_SCLK_MFC 0xc828
+#define GATE_SCLK_G3D 0xc82c
+#define GATE_SCLK_LCD 0xc834
+#define GATE_SCLK_MAUDIO 0xc83c
+#define GATE_SCLK_FSYS 0xc840
+#define GATE_SCLK_PERIL 0xc850
+#define GATE_IP_CAM 0xc920
+#define GATE_IP_TV 0xc924
+#define GATE_IP_MFC 0xc928
+#define GATE_IP_G3D 0xc92c
+#define GATE_IP_LCD 0xc934
+#define GATE_IP_FSYS 0xc940
+#define GATE_IP_PERIL 0xc950
+#define GATE_BLOCK 0xc970
+#define APLL_LOCK 0x14000
+#define APLL_CON0 0x14100
+#define SRC_CPU 0x14200
+#define DIV_CPU0 0x14500
+#define DIV_CPU1 0x14504
+
+enum exynos4415_plls {
+ apll, epll, g3d_pll, isp_pll, disp_pll,
+ nr_plls,
+};
+
+/*
+ * Support for CMU save/restore across system suspends
+ */
+#ifdef CONFIG_PM_SLEEP
+static struct samsung_clk_reg_dump *clk_regs;
+static struct samsung_clk_provider *ctx;
+
+static unsigned long cmu_clk_regs[] __initdata = {
+ SRC_LEFTBUS,
+ DIV_LEFTBUS,
+ GATE_IP_LEFTBUS,
+ GATE_IP_IMAGE,
+ SRC_RIGHTBUS,
+ DIV_RIGHTBUS,
+ GATE_IP_RIGHTBUS,
+ GATE_IP_PERIR,
+ EPLL_LOCK,
+ G3D_PLL_LOCK,
+ DISP_PLL_LOCK,
+ ISP_PLL_LOCK,
+ EPLL_CON0,
+ EPLL_CON1,
+ EPLL_CON2,
+ G3D_PLL_CON0,
+ G3D_PLL_CON1,
+ G3D_PLL_CON2,
+ ISP_PLL_CON0,
+ ISP_PLL_CON1,
+ ISP_PLL_CON2,
+ DISP_PLL_CON0,
+ DISP_PLL_CON1,
+ DISP_PLL_CON2,
+ SRC_TOP0,
+ SRC_TOP1,
+ SRC_CAM,
+ SRC_TV,
+ SRC_MFC,
+ SRC_G3D,
+ SRC_LCD,
+ SRC_ISP,
+ SRC_MAUDIO,
+ SRC_FSYS,
+ SRC_PERIL0,
+ SRC_PERIL1,
+ SRC_CAM1,
+ SRC_TOP_ISP0,
+ SRC_TOP_ISP1,
+ SRC_MASK_TOP,
+ SRC_MASK_CAM,
+ SRC_MASK_TV,
+ SRC_MASK_LCD,
+ SRC_MASK_ISP,
+ SRC_MASK_MAUDIO,
+ SRC_MASK_FSYS,
+ SRC_MASK_PERIL0,
+ SRC_MASK_PERIL1,
+ DIV_TOP,
+ DIV_CAM,
+ DIV_TV,
+ DIV_MFC,
+ DIV_G3D,
+ DIV_LCD,
+ DIV_ISP,
+ DIV_MAUDIO,
+ DIV_FSYS0,
+ DIV_FSYS1,
+ DIV_FSYS2,
+ DIV_PERIL0,
+ DIV_PERIL1,
+ DIV_PERIL2,
+ DIV_PERIL3,
+ DIV_PERIL4,
+ DIV_PERIL5,
+ DIV_CAM1,
+ DIV_TOP_ISP1,
+ DIV_TOP_ISP0,
+ CLKDIV2_RATIO,
+ GATE_SCLK_CAM,
+ GATE_SCLK_TV,
+ GATE_SCLK_MFC,
+ GATE_SCLK_G3D,
+ GATE_SCLK_LCD,
+ GATE_SCLK_MAUDIO,
+ GATE_SCLK_FSYS,
+ GATE_SCLK_PERIL,
+ GATE_IP_CAM,
+ GATE_IP_TV,
+ GATE_IP_MFC,
+ GATE_IP_G3D,
+ GATE_IP_LCD,
+ GATE_IP_FSYS,
+ GATE_IP_PERIL,
+ GATE_BLOCK,
+ APLL_LOCK,
+ APLL_CON0,
+ SRC_CPU,
+ DIV_CPU0,
+ DIV_CPU1,
+};
+
+static int exynos_clk_suspend(void)
+{
+ samsung_clk_save(ctx->reg_base, clk_regs, ARRAY_SIZE(cmu_clk_regs));
+
+ return 0;
+}
+
+static void exynos_clk_resume(void)
+{
+ samsung_clk_restore(ctx->reg_base, clk_regs, ARRAY_SIZE(cmu_clk_regs));
+}
+
+static struct syscore_ops exynos_clk_syscore_ops = {
+ .suspend = exynos_clk_suspend,
+ .resume = exynos_clk_resume,
+};
+
+static void exynos_clk_sleep_init(void)
+{
+ clk_regs = samsung_clk_alloc_reg_dump(cmu_clk_regs,
+ ARRAY_SIZE(cmu_clk_regs));
+ if (!clk_regs) {
+ pr_warn("%s: Failed to allocate sleep save data\n", __func__);
+ goto err;
+ }
+
+ register_syscore_ops(&exynos_clk_syscore_ops);
+
+ return;
+err:
+ if (clk_regs)
+ kfree(clk_regs);
+}
+#else
+static inline void exynos_clk_sleep_init(void) { }
+#endif
+
+/* list of all parent clock list */
+PNAME(mout_g3d_pllsrc_p) = { "fin_pll", };
+
+PNAME(mout_apll_p) = { "fin_pll", "fout_apll", };
+PNAME(mout_g3d_pll_p) = { "fin_pll", "fout_g3d_pll", };
+PNAME(mout_isp_pll_p) = { "fin_pll", "fout_isp_pll", };
+PNAME(mout_disp_pll_p) = { "fin_pll", "fout_disp_pll", };
+
+PNAME(mout_mpll_user_p) = { "fin_pll", "div_mpll_pre", };
+PNAME(mout_epll_p) = { "fin_pll", "fout_epll", };
+PNAME(mout_core_p) = { "mout_apll", "mout_mpll_user_c", };
+PNAME(mout_hpm_p) = { "mout_apll", "mout_mpll_user_c", };
+
+PNAME(mout_ebi_p) = { "div_aclk_200", "div_aclk_160", };
+PNAME(mout_ebi_1_p) = { "mout_ebi", "mout_g3d_pll", };
+
+PNAME(mout_gdl_p) = { "mout_mpll_user_l", };
+PNAME(mout_gdr_p) = { "mout_mpll_user_r", };
+
+PNAME(mout_aclk_266_p) = { "mout_mpll_user_t", "mout_g3d_pll", };
+
+PNAME(group_epll_g3dpll_p) = { "mout_epll", "mout_g3d_pll" };
+PNAME(group_sclk_p) = { "xxti", "xusbxti",
+ "none", "mout_isp_pll",
+ "none", "none", "div_mpll_pre",
+ "mout_epll", "mout_g3d_pll", };
+PNAME(group_spdif_p) = { "mout_audio0", "mout_audio1",
+ "mout_audio2", "spdif_extclk", };
+PNAME(group_sclk_audio2_p) = { "audiocdclk2", "none",
+ "none", "mout_isp_pll",
+ "mout_disp_pll", "xusbxti",
+ "div_mpll_pre", "mout_epll",
+ "mout_g3d_pll", };
+PNAME(group_sclk_audio1_p) = { "audiocdclk1", "none",
+ "none", "mout_isp_pll",
+ "mout_disp_pll", "xusbxti",
+ "div_mpll_pre", "mout_epll",
+ "mout_g3d_pll", };
+PNAME(group_sclk_audio0_p) = { "audiocdclk0", "none",
+ "none", "mout_isp_pll",
+ "mout_disp_pll", "xusbxti",
+ "div_mpll_pre", "mout_epll",
+ "mout_g3d_pll", };
+PNAME(group_fimc_lclk_p) = { "xxti", "xusbxti",
+ "none", "mout_isp_pll",
+ "none", "mout_disp_pll",
+ "mout_mpll_user_t", "mout_epll",
+ "mout_g3d_pll", };
+PNAME(group_sclk_fimd0_p) = { "xxti", "xusbxti",
+ "m_bitclkhsdiv4_4l", "mout_isp_pll",
+ "mout_disp_pll", "sclk_hdmiphy",
+ "div_mpll_pre", "mout_epll",
+ "mout_g3d_pll", };
+PNAME(mout_hdmi_p) = { "sclk_pixel", "sclk_hdmiphy" };
+PNAME(mout_mfc_p) = { "mout_mfc_0", "mout_mfc_1" };
+PNAME(mout_g3d_p) = { "mout_g3d_0", "mout_g3d_1" };
+PNAME(mout_jpeg_p) = { "mout_jpeg_0", "mout_jpeg_1" };
+PNAME(mout_jpeg1_p) = { "mout_epll", "mout_g3d_pll" };
+PNAME(group_aclk_isp0_300_p) = { "mout_isp_pll", "div_mpll_pre" };
+PNAME(group_aclk_isp0_400_user_p) = { "fin_pll", "div_aclk_400_mcuisp" };
+PNAME(group_aclk_isp0_300_user_p) = { "fin_pll", "mout_aclk_isp0_300" };
+PNAME(group_aclk_isp1_300_user_p) = { "fin_pll", "mout_aclk_isp1_300" };
+PNAME(group_mout_mpll_user_t_p) = { "mout_mpll_user_t" };
+
+static struct samsung_fixed_factor_clock fixed_factor_clks[] __initdata = {
+ /* HACK: fin_pll hardcoded to xusbxti until detection is implemented. */
+ FFACTOR(CLK_FIN_PLL, "fin_pll", "xusbxti", 1, 1, 0),
+};
+
+static struct samsung_fixed_rate_clock fixed_rate_clks[] __initdata = {
+ FRATE(CLK_SCLK_HDMIPHY, "sclk_hdmiphy", NULL, CLK_IS_ROOT, 27000000),
+};
+
+static struct samsung_mux_clock mux_clks[] __initdata = {
+ /*
+ * NOTE: Following table is sorted by register address in ascending
+ * order and then bitfield shift in descending order, as it is done
+ * in the User's Manual. When adding new entries, please make sure
+ * that the order is preserved, to avoid merge conflicts and make
+ * further work with defined data easier.
+ */
+
+ /* SRC_LEFTBUS */
+ MUX(CLK_MOUT_MPLL_USER_L, "mout_mpll_user_l", mout_mpll_user_p,
+ SRC_LEFTBUS, 4, 1),
+ MUX(CLK_MOUT_GDL, "mout_gdl", mout_gdl_p, SRC_LEFTBUS, 0, 1),
+
+ /* SRC_RIGHTBUS */
+ MUX(CLK_MOUT_MPLL_USER_R, "mout_mpll_user_r", mout_mpll_user_p,
+ SRC_RIGHTBUS, 4, 1),
+ MUX(CLK_MOUT_GDR, "mout_gdr", mout_gdr_p, SRC_RIGHTBUS, 0, 1),
+
+ /* SRC_TOP0 */
+ MUX(CLK_MOUT_EBI, "mout_ebi", mout_ebi_p, SRC_TOP0, 28, 1),
+ MUX(CLK_MOUT_ACLK_200, "mout_aclk_200", group_mout_mpll_user_t_p,
+ SRC_TOP0, 24, 1),
+ MUX(CLK_MOUT_ACLK_160, "mout_aclk_160", group_mout_mpll_user_t_p,
+ SRC_TOP0, 20, 1),
+ MUX(CLK_MOUT_ACLK_100, "mout_aclk_100", group_mout_mpll_user_t_p,
+ SRC_TOP0, 16, 1),
+ MUX(CLK_MOUT_ACLK_266, "mout_aclk_266", mout_aclk_266_p,
+ SRC_TOP0, 12, 1),
+ MUX(CLK_MOUT_G3D_PLL, "mout_g3d_pll", mout_g3d_pll_p,
+ SRC_TOP0, 8, 1),
+ MUX(CLK_MOUT_EPLL, "mout_epll", mout_epll_p, SRC_TOP0, 4, 1),
+ MUX(CLK_MOUT_EBI_1, "mout_ebi_1", mout_ebi_1_p, SRC_TOP0, 0, 1),
+
+ /* SRC_TOP1 */
+ MUX(CLK_MOUT_ISP_PLL, "mout_isp_pll", mout_isp_pll_p,
+ SRC_TOP1, 28, 1),
+ MUX(CLK_MOUT_DISP_PLL, "mout_disp_pll", mout_disp_pll_p,
+ SRC_TOP1, 16, 1),
+ MUX(CLK_MOUT_MPLL_USER_T, "mout_mpll_user_t", mout_mpll_user_p,
+ SRC_TOP1, 12, 1),
+ MUX(CLK_MOUT_ACLK_400_MCUISP, "mout_aclk_400_mcuisp",
+ group_mout_mpll_user_t_p, SRC_TOP1, 8, 1),
+ MUX(CLK_MOUT_G3D_PLLSRC, "mout_g3d_pllsrc", mout_g3d_pllsrc_p,
+ SRC_TOP1, 0, 1),
+
+ /* SRC_CAM */
+ MUX(CLK_MOUT_CSIS1, "mout_csis1", group_fimc_lclk_p, SRC_CAM, 28, 4),
+ MUX(CLK_MOUT_CSIS0, "mout_csis0", group_fimc_lclk_p, SRC_CAM, 24, 4),
+ MUX(CLK_MOUT_CAM1, "mout_cam1", group_fimc_lclk_p, SRC_CAM, 20, 4),
+ MUX(CLK_MOUT_FIMC3_LCLK, "mout_fimc3_lclk", group_fimc_lclk_p, SRC_CAM,
+ 12, 4),
+ MUX(CLK_MOUT_FIMC2_LCLK, "mout_fimc2_lclk", group_fimc_lclk_p, SRC_CAM,
+ 8, 4),
+ MUX(CLK_MOUT_FIMC1_LCLK, "mout_fimc1_lclk", group_fimc_lclk_p, SRC_CAM,
+ 4, 4),
+ MUX(CLK_MOUT_FIMC0_LCLK, "mout_fimc0_lclk", group_fimc_lclk_p, SRC_CAM,
+ 0, 4),
+
+ /* SRC_TV */
+ MUX(CLK_MOUT_HDMI, "mout_hdmi", mout_hdmi_p, SRC_TV, 0, 1),
+
+ /* SRC_MFC */
+ MUX(CLK_MOUT_MFC, "mout_mfc", mout_mfc_p, SRC_MFC, 8, 1),
+ MUX(CLK_MOUT_MFC_1, "mout_mfc_1", group_epll_g3dpll_p, SRC_MFC, 4, 1),
+ MUX(CLK_MOUT_MFC_0, "mout_mfc_0", group_mout_mpll_user_t_p, SRC_MFC, 0,
+ 1),
+
+ /* SRC_G3D */
+ MUX(CLK_MOUT_G3D, "mout_g3d", mout_g3d_p, SRC_G3D, 8, 1),
+ MUX(CLK_MOUT_G3D_1, "mout_g3d_1", group_epll_g3dpll_p, SRC_G3D, 4, 1),
+ MUX(CLK_MOUT_G3D_0, "mout_g3d_0", group_mout_mpll_user_t_p, SRC_G3D, 0,
+ 1),
+
+ /* SRC_LCD */
+ MUX(CLK_MOUT_MIPI0, "mout_mipi0", group_fimc_lclk_p, SRC_LCD, 12, 4),
+ MUX(CLK_MOUT_FIMD0, "mout_fimd0", group_sclk_fimd0_p, SRC_LCD, 0, 4),
+
+ /* SRC_ISP */
+ MUX(CLK_MOUT_TSADC_ISP, "mout_tsadc_isp", group_fimc_lclk_p, SRC_ISP,
+ 16, 4),
+ MUX(CLK_MOUT_UART_ISP, "mout_uart_isp", group_fimc_lclk_p, SRC_ISP,
+ 12, 4),
+ MUX(CLK_MOUT_SPI1_ISP, "mout_spi1_isp", group_fimc_lclk_p, SRC_ISP,
+ 8, 4),
+ MUX(CLK_MOUT_SPI0_ISP, "mout_spi0_isp", group_fimc_lclk_p, SRC_ISP,
+ 4, 4),
+ MUX(CLK_MOUT_PWM_ISP, "mout_pwm_isp", group_fimc_lclk_p, SRC_ISP,
+ 0, 4),
+
+ /* SRC_MAUDIO */
+ MUX(CLK_MOUT_AUDIO0, "mout_audio0", group_sclk_audio0_p, SRC_MAUDIO,
+ 0,4),
+
+ /* SRC_FSYS */
+ MUX(CLK_MOUT_TSADC, "mout_tsadc", group_sclk_p, SRC_FSYS, 28, 4),
+ MUX(CLK_MOUT_MMC2, "mout_mmc2", group_sclk_p, SRC_FSYS, 8, 4),
+ MUX(CLK_MOUT_MMC1, "mout_mmc1", group_sclk_p, SRC_FSYS, 4, 4),
+ MUX(CLK_MOUT_MMC0, "mout_mmc0", group_sclk_p, SRC_FSYS, 0, 4),
+
+ /* SRC_PERIL0 */
+ MUX(CLK_MOUT_UART3, "mout_uart3", group_sclk_p, SRC_PERIL0, 12, 4),
+ MUX(CLK_MOUT_UART2, "mout_uart2", group_sclk_p, SRC_PERIL0, 8, 4),
+ MUX(CLK_MOUT_UART1, "mout_uart1", group_sclk_p, SRC_PERIL0, 4, 4),
+ MUX(CLK_MOUT_UART0, "mout_uart0", group_sclk_p, SRC_PERIL0, 0, 4),
+
+ /* SRC_PERIL1 */
+ MUX(CLK_MOUT_SPI2, "mout_spi2", group_sclk_p, SRC_PERIL1, 24, 4),
+ MUX(CLK_MOUT_SPI1, "mout_spi1", group_sclk_p, SRC_PERIL1, 20, 4),
+ MUX(CLK_MOUT_SPI0, "mout_spi0", group_sclk_p, SRC_PERIL1, 16, 4),
+ MUX(CLK_MOUT_SPDIF, "mout_spdif", group_spdif_p, SRC_PERIL1, 8, 4),
+ MUX(CLK_MOUT_AUDIO2, "mout_audio2", group_sclk_audio2_p, SRC_PERIL1,
+ 4, 4),
+ MUX(CLK_MOUT_AUDIO1, "mout_audio1", group_sclk_audio1_p, SRC_PERIL1,
+ 0, 4),
+
+ /* SRC_CPU */
+ MUX(CLK_MOUT_MPLL_USER_C, "mout_mpll_user_c", mout_mpll_user_p,
+ SRC_CPU, 24, 1),
+ MUX(CLK_MOUT_HPM, "mout_hpm", mout_hpm_p, SRC_CPU, 20, 1),
+ MUX_F(CLK_MOUT_CORE, "mout_core", mout_core_p, SRC_CPU, 16, 1, 0,
+ CLK_MUX_READ_ONLY),
+ MUX_F(CLK_MOUT_APLL, "mout_apll", mout_apll_p, SRC_CPU, 0, 1,
+ CLK_SET_RATE_PARENT, 0),
+
+ /* SRC_CAM1 */
+ MUX(CLK_MOUT_PXLASYNC_CSIS1_FIMC, "mout_pxlasync_csis1",
+ group_fimc_lclk_p, SRC_CAM1, 20, 1),
+ MUX(CLK_MOUT_PXLASYNC_CSIS0_FIMC, "mout_pxlasync_csis0",
+ group_fimc_lclk_p, SRC_CAM1, 16, 1),
+ MUX(CLK_MOUT_JPEG, "mout_jpeg", mout_jpeg_p, SRC_CAM1, 8, 1),
+ MUX(CLK_MOUT_JPEG1, "mout_jpeg_1", mout_jpeg1_p, SRC_CAM1, 4, 1),
+ MUX(CLK_MOUT_JPEG0, "mout_jpeg_0", group_mout_mpll_user_t_p, SRC_CAM1,
+ 0, 1),
+
+ /* SRC_TOP_ISP0 */
+ MUX(CLK_MOUT_ACLK_ISP0_300, "mout_aclk_isp0_300",
+ group_aclk_isp0_300_p, SRC_TOP_ISP0, 8, 1),
+ MUX(CLK_MOUT_ACLK_ISP0_400, "mout_aclk_isp0_400_user",
+ group_aclk_isp0_400_user_p, SRC_TOP_ISP0, 4, 1),
+ MUX(CLK_MOUT_ACLK_ISP0_300_USER, "mout_aclk_isp0_300_user",
+ group_aclk_isp0_300_user_p, SRC_TOP_ISP0, 0, 1),
+
+ /* SRC_TOP_ISP1 */
+ MUX(CLK_MOUT_ACLK_ISP1_300, "mout_aclk_isp1_300",
+ group_aclk_isp0_300_p, SRC_TOP_ISP1, 4, 1),
+ MUX(CLK_MOUT_ACLK_ISP1_300_USER, "mout_aclk_isp1_300_user",
+ group_aclk_isp1_300_user_p, SRC_TOP_ISP1, 0, 1),
+};
+
+static struct samsung_div_clock div_clks[] __initdata = {
+ /*
+ * NOTE: Following table is sorted by register address in ascending
+ * order and then bitfield shift in descending order, as it is done
+ * in the User's Manual. When adding new entries, please make sure
+ * that the order is preserved, to avoid merge conflicts and make
+ * further work with defined data easier.
+ */
+
+ /* DIV_LEFTBUS */
+ DIV(CLK_DIV_GPL, "div_gpl", "div_gdl", DIV_LEFTBUS, 4, 3),
+ DIV(CLK_DIV_GDL, "div_gdl", "mout_gdl", DIV_LEFTBUS, 0, 4),
+
+ /* DIV_RIGHTBUS */
+ DIV(CLK_DIV_GPR, "div_gpr", "div_gdr", DIV_RIGHTBUS, 4, 3),
+ DIV(CLK_DIV_GDR, "div_gdr", "mout_gdr", DIV_RIGHTBUS, 0, 4),
+
+ /* DIV_TOP */
+ DIV(CLK_DIV_ACLK_400_MCUISP, "div_aclk_400_mcuisp",
+ "mout_aclk_400_mcuisp", DIV_TOP, 24, 3),
+ DIV(CLK_DIV_EBI, "div_ebi", "mout_ebi_1", DIV_TOP, 16, 3),
+ DIV(CLK_DIV_ACLK_200, "div_aclk_200", "mout_aclk_200", DIV_TOP, 12, 3),
+ DIV(CLK_DIV_ACLK_160, "div_aclk_160", "mout_aclk_160", DIV_TOP, 8, 3),
+ DIV(CLK_DIV_ACLK_100, "div_aclk_100", "mout_aclk_100", DIV_TOP, 4, 4),
+ DIV(CLK_DIV_ACLK_266, "div_aclk_266", "mout_aclk_266", DIV_TOP, 0, 3),
+
+ /* DIV_CAM */
+ DIV(CLK_DIV_CSIS1, "div_csis1", "mout_csis1", DIV_CAM, 28, 4),
+ DIV(CLK_DIV_CSIS0, "div_csis0", "mout_csis0", DIV_CAM, 24, 4),
+ DIV(CLK_DIV_CAM1, "div_cam1", "mout_cam1", DIV_CAM, 20, 4),
+ DIV(CLK_DIV_FIMC3_LCLK, "div_fimc3_lclk", "mout_fimc3_lclk", DIV_CAM,
+ 12, 4),
+ DIV(CLK_DIV_FIMC2_LCLK, "div_fimc2_lclk", "mout_fimc2_lclk", DIV_CAM,
+ 8, 4),
+ DIV(CLK_DIV_FIMC1_LCLK, "div_fimc1_lclk", "mout_fimc1_lclk", DIV_CAM,
+ 4, 4),
+ DIV(CLK_DIV_FIMC0_LCLK, "div_fimc0_lclk", "mout_fimc0_lclk", DIV_CAM,
+ 0, 4),
+
+ /* DIV_TV */
+ DIV(CLK_DIV_TV_BLK, "div_tv_blk", "mout_g3d_pll", DIV_TV, 0, 4),
+
+ /* DIV_MFC */
+ DIV(CLK_DIV_MFC, "div_mfc", "mout_mfc", DIV_MFC, 0, 4),
+
+ /* DIV_G3D */
+ DIV(CLK_DIV_G3D, "div_g3d", "mout_g3d", DIV_G3D, 0, 4),
+
+ /* DIV_LCD */
+ DIV_F(CLK_DIV_MIPI0_PRE, "div_mipi0_pre", "div_mipi0", DIV_LCD, 20, 4,
+ CLK_SET_RATE_PARENT, 0),
+ DIV(CLK_DIV_MIPI0, "div_mipi0", "mout_mipi0", DIV_LCD, 16, 4),
+ DIV(CLK_DIV_FIMD0, "div_fimd0", "mout_fimd0", DIV_LCD, 0, 4),
+
+ /* DIV_ISP */
+ DIV(CLK_DIV_UART_ISP, "div_uart_isp", "mout_uart_isp", DIV_ISP, 28, 4),
+ DIV_F(CLK_DIV_SPI1_ISP_PRE, "div_spi1_isp_pre", "div_spi1_isp",
+ DIV_ISP, 20, 8, CLK_SET_RATE_PARENT, 0),
+ DIV(CLK_DIV_SPI1_ISP, "div_spi1_isp", "mout_spi1_isp", DIV_ISP, 16, 4),
+ DIV_F(CLK_DIV_SPI0_ISP_PRE, "div_spi0_isp_pre", "div_spi0_isp",
+ DIV_ISP, 8, 8, CLK_SET_RATE_PARENT, 0),
+ DIV(CLK_DIV_SPI0_ISP, "div_spi0_isp", "mout_spi0_isp", DIV_ISP, 4, 4),
+ DIV(CLK_DIV_PWM_ISP, "div_pwm_isp", "mout_pwm_isp", DIV_ISP, 0, 4),
+
+ /* DIV_MAUDIO */
+ DIV(CLK_DIV_PCM0, "div_pcm0", "div_audio0", DIV_MAUDIO, 4, 8),
+ DIV(CLK_DIV_AUDIO0, "div_audio0", "mout_audio0", DIV_MAUDIO, 0, 4),
+
+ /* DIV_FSYS0 */
+ DIV_F(CLK_DIV_TSADC_PRE, "div_tsadc_pre", "div_tsadc", DIV_FSYS0, 8, 8,
+ CLK_SET_RATE_PARENT, 0),
+ DIV(CLK_DIV_TSADC, "div_tsadc", "mout_tsadc", DIV_FSYS0, 0, 4),
+
+ /* DIV_FSYS1 */
+ DIV_F(CLK_DIV_MMC1_PRE, "div_mmc1_pre", "div_mmc1", DIV_FSYS1, 24, 8,
+ CLK_SET_RATE_PARENT, 0),
+ DIV(CLK_DIV_MMC1, "div_mmc1", "mout_mmc1", DIV_FSYS1, 16, 4),
+ DIV_F(CLK_DIV_MMC0_PRE, "div_mmc0_pre", "div_mmc0", DIV_FSYS1, 8, 8,
+ CLK_SET_RATE_PARENT, 0),
+ DIV(CLK_DIV_MMC0, "div_mmc0", "mout_mmc0", DIV_FSYS1, 0, 4),
+
+ /* DIV_FSYS2 */
+ DIV_F(CLK_DIV_MMC2_PRE, "div_mmc2_pre", "div_mmc2", DIV_FSYS2, 8, 8,
+ CLK_SET_RATE_PARENT, 0),
+ DIV_F(CLK_DIV_MMC2_PRE, "div_mmc2", "mout_mmc2", DIV_FSYS2, 0, 4,
+ CLK_SET_RATE_PARENT, 0),
+
+ /* DIV_PERIL0 */
+ DIV(CLK_DIV_UART3, "div_uart3", "mout_uart3", DIV_PERIL0, 12, 4),
+ DIV(CLK_DIV_UART2, "div_uart2", "mout_uart2", DIV_PERIL0, 8, 4),
+ DIV(CLK_DIV_UART1, "div_uart1", "mout_uart1", DIV_PERIL0, 4, 4),
+ DIV(CLK_DIV_UART0, "div_uart0", "mout_uart0", DIV_PERIL0, 0, 4),
+
+ /* DIV_PERIL1 */
+ DIV_F(CLK_DIV_SPI1_PRE, "div_spi1_pre", "div_spi1", DIV_PERIL1, 24, 8,
+ CLK_SET_RATE_PARENT, 0),
+ DIV(CLK_DIV_SPI1, "div_spi1", "mout_spi1", DIV_PERIL1, 16, 4),
+ DIV_F(CLK_DIV_SPI0_PRE, "div_spi0_pre", "div_spi0", DIV_PERIL1, 8, 8,
+ CLK_SET_RATE_PARENT, 0),
+ DIV(CLK_DIV_SPI0, "div_spi0", "mout_spi0", DIV_PERIL1, 0, 4),
+
+ /* DIV_PERIL2 */
+ DIV_F(CLK_DIV_SPI2_PRE, "div_spi2_pre", "div_spi2", DIV_PERIL2, 8, 8,
+ CLK_SET_RATE_PARENT, 0),
+ DIV(CLK_DIV_SPI2, "div_spi2", "mout_spi2", DIV_PERIL2, 0, 4),
+
+ /* DIV_PERIL4 */
+ DIV(CLK_DIV_PCM2, "div_pcm2", "div_audio2", DIV_PERIL4, 20, 8),
+ DIV(CLK_DIV_AUDIO2, "div_audio2", "mout_audio2", DIV_PERIL4, 16, 4),
+ DIV(CLK_DIV_PCM1, "div_pcm1", "div_audio1", DIV_PERIL4, 20, 8),
+ DIV(CLK_DIV_AUDIO1, "div_audio1", "mout_audio1", DIV_PERIL4, 0, 4),
+
+ /* DIV_PERIL5 */
+ DIV(CLK_DIV_I2S1, "div_i2s1", "div_audio1", DIV_PERIL5, 0, 6),
+
+ /* DIV_CAM1 */
+ DIV(CLK_DIV_PXLASYNC_CSIS1_FIMC, "div_pxlasync_csis1_fimc",
+ "mout_pxlasync_csis1", DIV_CAM1, 24, 4),
+ DIV(CLK_DIV_PXLASYNC_CSIS0_FIMC, "div_pxlasync_csis0_fimc",
+ "mout_pxlasync_csis0", DIV_CAM1, 20, 4),
+ DIV(CLK_DIV_JPEG, "div_jpeg", "mout_jpeg", DIV_CAM1, 0, 4),
+
+ /* DIV_CPU0 */
+ DIV(CLK_DIV_CORE2, "div_core2", "div_core", DIV_CPU0, 28, 3),
+ DIV_F(CLK_DIV_APLL, "div_apll", "mout_apll", DIV_CPU0, 24, 3,
+ CLK_GET_RATE_NOCACHE, CLK_DIVIDER_READ_ONLY),
+ DIV(CLK_DIV_PCLK_DBG, "div_pclk_dbg", "div_core2", DIV_CPU0, 20, 3),
+ DIV(CLK_DIV_ATB, "div_atb", "div_core2", DIV_CPU0, 16, 3),
+ DIV(CLK_DIV_PERIPH, "div_periph", "div_core2", DIV_CPU0, 12, 3),
+ DIV(CLK_DIV_COREM1, "div_corem1", "div_core2", DIV_CPU0, 8, 3),
+ DIV(CLK_DIV_COREM0, "div_corem0", "div_core2", DIV_CPU0, 4, 3),
+ DIV_F(CLK_DIV_CORE, "div_core", "mout_core", DIV_CPU0, 0, 3,
+ CLK_GET_RATE_NOCACHE, CLK_DIVIDER_READ_ONLY),
+
+ /* DIV_CPU1 */
+ DIV(CLK_DIV_HPM, "div_hpm", "div_copy", DIV_CPU1, 4, 3),
+ DIV(CLK_DIV_COPY, "div_copy", "mout_hpm", DIV_CPU1, 0, 3),
+};
+
+static struct samsung_gate_clock gate_clks[] __initdata = {
+ /*
+ * NOTE: Following table is sorted by register address in ascending
+ * order and then bitfield shift in descending order, as it is done
+ * in the User's Manual. When adding new entries, please make sure
+ * that the order is preserved, to avoid merge conflicts and make
+ * further work with defined data easier.
+ */
+
+ /* GATE_IP_LEFTBUS */
+ GATE(CLK_ASYNC_G3D, "async_g3d", "div_aclk_100", GATE_IP_LEFTBUS, 6,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_ASYNC_MFCL, "async_mfcl", "div_aclk_100", GATE_IP_LEFTBUS, 4,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_ASYNC_TVX, "async_tvx", "div_aclk_100", GATE_IP_LEFTBUS, 3,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_PPMULEFT, "ppmuleft", "div_aclk_100", GATE_IP_LEFTBUS, 1,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_GPIO_LEFT, "gpio_left", "div_aclk_100", GATE_IP_LEFTBUS, 0,
+ CLK_IGNORE_UNUSED, 0),
+
+ /* GATE_IP_IMAGE */
+ GATE(CLK_PPMUIMAGE, "ppmuimage", "div_aclk_100", GATE_IP_IMAGE,
+ 9, 0, 0),
+ GATE(CLK_QEMDMA2, "qe_mdma2", "div_aclk_100", GATE_IP_IMAGE,
+ 8, 0, 0),
+ GATE(CLK_QEROTATOR, "qe_rotator", "div_aclk_100", GATE_IP_IMAGE,
+ 7, 0, 0),
+ GATE(CLK_SMMUMDMA2, "smmu_mdam2", "div_aclk_100", GATE_IP_IMAGE,
+ 5, 0, 0),
+ GATE(CLK_SMMUROTATOR, "smmu_rotator", "div_aclk_100", GATE_IP_IMAGE,
+ 4, 0, 0),
+ GATE(CLK_MDMA2, "mdma2", "div_aclk_100", GATE_IP_IMAGE, 2, 0, 0),
+ GATE(CLK_ROTATOR, "rotator", "div_aclk_100", GATE_IP_IMAGE, 1, 0, 0),
+
+ /* GATE_IP_RIGHTBUS */
+ GATE(CLK_ASYNC_ISPMX, "async_ispmx", "div_aclk_100",
+ GATE_IP_RIGHTBUS, 9, CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_ASYNC_MAUDIOX, "async_maudiox", "div_aclk_100",
+ GATE_IP_RIGHTBUS, 7, CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_ASYNC_MFCR, "async_mfcr", "div_aclk_100",
+ GATE_IP_RIGHTBUS, 6, CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_ASYNC_FSYSD, "async_fsysd", "div_aclk_100",
+ GATE_IP_RIGHTBUS, 5, CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_ASYNC_LCD0X, "async_lcd0x", "div_aclk_100",
+ GATE_IP_RIGHTBUS, 3, CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_ASYNC_CAMX, "async_camx", "div_aclk_100",
+ GATE_IP_RIGHTBUS, 2, CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_PPMURIGHT, "ppmuright", "div_aclk_100",
+ GATE_IP_RIGHTBUS, 1, CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_GPIO_RIGHT, "gpio_right", "div_aclk_100",
+ GATE_IP_RIGHTBUS, 0, CLK_IGNORE_UNUSED, 0),
+
+ /* GATE_IP_PERIR */
+ GATE(CLK_ANTIRBK_APBIF, "antirbk_apbif", "div_aclk_100",
+ GATE_IP_PERIR, 24, CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_EFUSE_WRITER_APBIF, "efuse_writer_apbif", "div_aclk_100",
+ GATE_IP_PERIR, 23, CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_MONOCNT, "monocnt", "div_aclk_100", GATE_IP_PERIR, 22,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_TZPC6, "tzpc6", "div_aclk_100", GATE_IP_PERIR, 21,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_PROVISIONKEY1, "provisionkey1", "div_aclk_100",
+ GATE_IP_PERIR, 20, CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_PROVISIONKEY0, "provisionkey0", "div_aclk_100",
+ GATE_IP_PERIR, 19, CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_CMU_ISPPART, "cmu_isppart", "div_aclk_100", GATE_IP_PERIR, 18,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_TMU_APBIF, "tmu_apbif", "div_aclk_100",
+ GATE_IP_PERIR, 17, 0, 0),
+ GATE(CLK_KEYIF, "keyif", "div_aclk_100", GATE_IP_PERIR, 16, 0, 0),
+ GATE(CLK_RTC, "rtc", "div_aclk_100", GATE_IP_PERIR, 15, 0, 0),
+ GATE(CLK_WDT, "wdt", "div_aclk_100", GATE_IP_PERIR, 14, 0, 0),
+ GATE(CLK_MCT, "mct", "div_aclk_100", GATE_IP_PERIR, 13, 0, 0),
+ GATE(CLK_SECKEY, "seckey", "div_aclk_100", GATE_IP_PERIR, 12,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_HDMI_CEC, "hdmi_cec", "div_aclk_100", GATE_IP_PERIR, 11,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_TZPC5, "tzpc5", "div_aclk_100", GATE_IP_PERIR, 10,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_TZPC4, "tzpc4", "div_aclk_100", GATE_IP_PERIR, 9,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_TZPC3, "tzpc3", "div_aclk_100", GATE_IP_PERIR, 8,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_TZPC2, "tzpc2", "div_aclk_100", GATE_IP_PERIR, 7,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_TZPC1, "tzpc1", "div_aclk_100", GATE_IP_PERIR, 6,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_TZPC0, "tzpc0", "div_aclk_100", GATE_IP_PERIR, 5,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_CMU_COREPART, "cmu_corepart", "div_aclk_100", GATE_IP_PERIR, 4,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_CMU_TOPPART, "cmu_toppart", "div_aclk_100", GATE_IP_PERIR, 3,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_PMU_APBIF, "pmu_apbif", "div_aclk_100", GATE_IP_PERIR, 2,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_SYSREG, "sysreg", "div_aclk_100", GATE_IP_PERIR, 1,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_CHIP_ID, "chip_id", "div_aclk_100", GATE_IP_PERIR, 0,
+ CLK_IGNORE_UNUSED, 0),
+
+ /* GATE_SCLK_CAM - non-completed */
+ GATE(CLK_SCLK_PXLAYSNC_CSIS1_FIMC, "sclk_pxlasync_csis1_fimc",
+ "div_pxlasync_csis1_fimc", GATE_SCLK_CAM, 11,
+ CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_PXLAYSNC_CSIS0_FIMC, "sclk_pxlasync_csis0_fimc",
+ "div_pxlasync_csis0_fimc", GATE_SCLK_CAM, 10, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_JPEG, "sclk_jpeg", "div_jpeg",
+ GATE_SCLK_CAM, 8, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_CSIS1, "sclk_csis1", "div_csis1",
+ GATE_SCLK_CAM, 7, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_CSIS0, "sclk_csis0", "div_csis0",
+ GATE_SCLK_CAM, 6, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_CAM1, "sclk_cam1", "div_cam1",
+ GATE_SCLK_CAM, 5, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_FIMC3_LCLK, "sclk_fimc3_lclk", "div_fimc3_lclk",
+ GATE_SCLK_CAM, 3, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_FIMC2_LCLK, "sclk_fimc2_lclk", "div_fimc2_lclk",
+ GATE_SCLK_CAM, 2, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_FIMC1_LCLK, "sclk_fimc1_lclk", "div_fimc1_lclk",
+ GATE_SCLK_CAM, 1, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_FIMC0_LCLK, "sclk_fimc0_lclk", "div_fimc0_lclk",
+ GATE_SCLK_CAM, 0, CLK_SET_RATE_PARENT, 0),
+
+ /* GATE_SCLK_TV */
+ GATE(CLK_SCLK_PIXEL, "sclk_pixel", "div_tv_blk",
+ GATE_SCLK_TV, 3, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_HDMI, "sclk_hdmi", "mout_hdmi",
+ GATE_SCLK_TV, 2, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_MIXER, "sclk_mixer", "div_tv_blk",
+ GATE_SCLK_TV, 0, CLK_SET_RATE_PARENT, 0),
+
+ /* GATE_SCLK_MFC */
+ GATE(CLK_SCLK_MFC, "sclk_mfc", "div_mfc",
+ GATE_SCLK_MFC, 0, CLK_SET_RATE_PARENT, 0),
+
+ /* GATE_SCLK_G3D */
+ GATE(CLK_SCLK_G3D, "sclk_g3d", "div_g3d",
+ GATE_SCLK_G3D, 0, CLK_SET_RATE_PARENT, 0),
+
+ /* GATE_SCLK_LCD */
+ GATE(CLK_SCLK_MIPIDPHY4L, "sclk_mipidphy4l", "div_mipi0",
+ GATE_SCLK_LCD, 4, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_MIPI0, "sclk_mipi0", "div_mipi0_pre",
+ GATE_SCLK_LCD, 3, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_MDNIE0, "sclk_mdnie0", "div_fimd0",
+ GATE_SCLK_LCD, 1, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_FIMD0, "sclk_fimd0", "div_fimd0",
+ GATE_SCLK_LCD, 0, CLK_SET_RATE_PARENT, 0),
+
+ /* GATE_SCLK_MAUDIO */
+ GATE(CLK_SCLK_PCM0, "sclk_pcm0", "div_pcm0",
+ GATE_SCLK_MAUDIO, 1, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_AUDIO0, "sclk_audio0", "div_audio0",
+ GATE_SCLK_MAUDIO, 0, CLK_SET_RATE_PARENT, 0),
+
+ /* GATE_SCLK_FSYS */
+ GATE(CLK_SCLK_TSADC, "sclk_tsadc", "div_tsadc_pre",
+ GATE_SCLK_FSYS, 9, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_EBI, "sclk_ebi", "div_ebi",
+ GATE_SCLK_FSYS, 6, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_MMC2, "sclk_mmc2", "div_mmc2_pre",
+ GATE_SCLK_FSYS, 2, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_MMC1, "sclk_mmc1", "div_mmc1_pre",
+ GATE_SCLK_FSYS, 1, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_MMC0, "sclk_mmc0", "div_mmc0_pre",
+ GATE_SCLK_FSYS, 0, CLK_SET_RATE_PARENT, 0),
+
+ /* GATE_SCLK_PERIL */
+ GATE(CLK_SCLK_I2S, "sclk_i2s1", "div_i2s1",
+ GATE_SCLK_PERIL, 18, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_PCM2, "sclk_pcm2", "div_pcm2",
+ GATE_SCLK_PERIL, 16, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_PCM1, "sclk_pcm1", "div_pcm1",
+ GATE_SCLK_PERIL, 15, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_AUDIO2, "sclk_audio2", "div_audio2",
+ GATE_SCLK_PERIL, 14, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_AUDIO1, "sclk_audio1", "div_audio1",
+ GATE_SCLK_PERIL, 13, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_SPDIF, "sclk_spdif", "mout_spdif",
+ GATE_SCLK_PERIL, 10, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_SPI2, "sclk_spi2", "div_spi2_pre",
+ GATE_SCLK_PERIL, 8, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_SPI1, "sclk_spi1", "div_spi1_pre",
+ GATE_SCLK_PERIL, 7, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_SPI0, "sclk_spi0", "div_spi0_pre",
+ GATE_SCLK_PERIL, 6, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_UART3, "sclk_uart3", "div_uart3",
+ GATE_SCLK_PERIL, 3, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_UART2, "sclk_uart2", "div_uart2",
+ GATE_SCLK_PERIL, 2, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_UART1, "sclk_uart1", "div_uart1",
+ GATE_SCLK_PERIL, 1, CLK_SET_RATE_PARENT, 0),
+ GATE(CLK_SCLK_UART0, "sclk_uart0", "div_uart0",
+ GATE_SCLK_PERIL, 0, CLK_SET_RATE_PARENT, 0),
+
+ /* GATE_IP_CAM */
+ GATE(CLK_SMMUFIMC_LITE2, "smmufimc_lite2", "div_aclk_160", GATE_IP_CAM, 22,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_FIMC_LITE2, "fimc_lite2", "div_aclk_160", GATE_IP_CAM, 20,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_PIXELASYNCM1, "pixelasyncm1", "div_aclk_160", GATE_IP_CAM, 18,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_PIXELASYNCM0, "pixelasyncm0", "div_aclk_160", GATE_IP_CAM, 17,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_PPMUCAMIF, "ppmucamif", "div_aclk_160", GATE_IP_CAM, 16,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_SMMUJPEG, "smmujpeg", "div_aclk_160", GATE_IP_CAM, 11, 0, 0),
+ GATE(CLK_SMMUFIMC3, "smmufimc3", "div_aclk_160", GATE_IP_CAM, 10, 0, 0),
+ GATE(CLK_SMMUFIMC2, "smmufimc2", "div_aclk_160", GATE_IP_CAM, 9, 0, 0),
+ GATE(CLK_SMMUFIMC1, "smmufimc1", "div_aclk_160", GATE_IP_CAM, 8, 0, 0),
+ GATE(CLK_SMMUFIMC0, "smmufimc0", "div_aclk_160", GATE_IP_CAM, 7, 0, 0),
+ GATE(CLK_JPEG, "jpeg", "div_aclk_160", GATE_IP_CAM, 6, 0, 0),
+ GATE(CLK_CSIS1, "csis1", "div_aclk_160", GATE_IP_CAM, 5, 0, 0),
+ GATE(CLK_CSIS0, "csis0", "div_aclk_160", GATE_IP_CAM, 4, 0, 0),
+ GATE(CLK_FIMC3, "fimc3", "div_aclk_160", GATE_IP_CAM, 3, 0, 0),
+ GATE(CLK_FIMC2, "fimc2", "div_aclk_160", GATE_IP_CAM, 2, 0, 0),
+ GATE(CLK_FIMC1, "fimc1", "div_aclk_160", GATE_IP_CAM, 1, 0, 0),
+ GATE(CLK_FIMC0, "fimc0", "div_aclk_160", GATE_IP_CAM, 0, 0, 0),
+
+ /* GATE_IP_TV */
+ GATE(CLK_PPMUTV, "ppmutv", "div_aclk_100", GATE_IP_TV, 5, 0, 0),
+ GATE(CLK_SMMUTV, "smmutv", "div_aclk_100", GATE_IP_TV, 4, 0, 0),
+ GATE(CLK_HDMI, "hdmi", "div_aclk_100", GATE_IP_TV, 3, 0, 0),
+ GATE(CLK_MIXER, "mixer", "div_aclk_100", GATE_IP_TV, 1, 0, 0),
+ GATE(CLK_VP, "vp", "div_aclk_100", GATE_IP_TV, 0, 0, 0),
+
+ /* GATE_IP_MFC */
+ GATE(CLK_PPMUMFC_R, "ppmumfc_r", "div_aclk_200", GATE_IP_MFC, 4,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_PPMUMFC_L, "ppmumfc_l", "div_aclk_200", GATE_IP_MFC, 3,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_SMMUMFC_R, "smmumfc_r", "div_aclk_200", GATE_IP_MFC, 2, 0, 0),
+ GATE(CLK_SMMUMFC_L, "smmumfc_l", "div_aclk_200", GATE_IP_MFC, 1, 0, 0),
+ GATE(CLK_MFC, "mfc", "div_aclk_200", GATE_IP_MFC, 0, 0, 0),
+
+ /* GATE_IP_G3D */
+ GATE(CLK_PPMUG3D, "ppmug3d", "div_aclk_200", GATE_IP_G3D, 1,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_G3D, "g3d", "div_aclk_200", GATE_IP_G3D, 0, 0, 0),
+
+ /* GATE_IP_LCD */
+ GATE(CLK_PPMULCD0, "ppmulcd0", "div_aclk_160", GATE_IP_LCD, 5,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_SMMUFIMD0, "smmufimd0", "div_aclk_160", GATE_IP_LCD, 4, 0, 0),
+ GATE(CLK_DSIM0, "dsim0", "div_aclk_160", GATE_IP_LCD, 3, 0, 0),
+ GATE(CLK_SMIES, "smies", "div_aclk_160", GATE_IP_LCD, 2, 0, 0),
+ GATE(CLK_MIE0, "mie0", "div_aclk_160", GATE_IP_LCD, 1, 0, 0),
+ GATE(CLK_FIMD0, "fimd0", "div_aclk_160", GATE_IP_LCD, 0, 0, 0),
+
+ /* GATE_IP_FSYS */
+ GATE(CLK_TSADC, "tsadc", "div_aclk_200", GATE_IP_FSYS, 20, 0, 0),
+ GATE(CLK_PPMUFILE, "ppmufile", "div_aclk_200", GATE_IP_FSYS, 17,
+ CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_NFCON, "nfcon", "div_aclk_200", GATE_IP_FSYS, 16, 0, 0),
+ GATE(CLK_USBDEVICE, "usbdevice", "div_aclk_200", GATE_IP_FSYS, 13, 0, 0),
+ GATE(CLK_USBHOST, "usbhost", "div_aclk_200", GATE_IP_FSYS, 12, 0, 0),
+ GATE(CLK_SROMC, "sromc", "div_aclk_200", GATE_IP_FSYS, 11, 0, 0),
+ GATE(CLK_SDMMC2, "sdmmc2", "div_aclk_200", GATE_IP_FSYS, 7, 0, 0),
+ GATE(CLK_SDMMC1, "sdmmc1", "div_aclk_200", GATE_IP_FSYS, 6, 0, 0),
+ GATE(CLK_SDMMC0, "sdmmc0", "div_aclk_200", GATE_IP_FSYS, 5, 0, 0),
+ GATE(CLK_PDMA1, "pdma1", "div_aclk_200", GATE_IP_FSYS, 1, 0, 0),
+ GATE(CLK_PDMA0, "pdma0", "div_aclk_200", GATE_IP_FSYS, 0, 0, 0),
+
+ /* GATE_IP_PERIL */
+ GATE(CLK_SPDIF, "spdif", "div_aclk_100", GATE_IP_PERIL, 26, 0, 0),
+ GATE(CLK_PWM, "pwm", "div_aclk_100", GATE_IP_PERIL, 24, 0, 0),
+ GATE(CLK_PCM2, "pcm2", "div_aclk_100", GATE_IP_PERIL, 23, 0, 0),
+ GATE(CLK_PCM1, "pcm1", "div_aclk_100", GATE_IP_PERIL, 22, 0, 0),
+ GATE(CLK_I2S1, "i2s1", "div_aclk_100", GATE_IP_PERIL, 20, 0, 0),
+ GATE(CLK_SPI2, "spi2", "div_aclk_100", GATE_IP_PERIL, 18, 0, 0),
+ GATE(CLK_SPI1, "spi1", "div_aclk_100", GATE_IP_PERIL, 17, 0, 0),
+ GATE(CLK_SPI0, "spi0", "div_aclk_100", GATE_IP_PERIL, 16, 0, 0),
+ GATE(CLK_I2CHDMI, "i2chdmi", "div_aclk_100", GATE_IP_PERIL, 14, 0, 0),
+ GATE(CLK_I2C7, "i2c7", "div_aclk_100", GATE_IP_PERIL, 13, 0, 0),
+ GATE(CLK_I2C6, "i2c6", "div_aclk_100", GATE_IP_PERIL, 12, 0, 0),
+ GATE(CLK_I2C5, "i2c5", "div_aclk_100", GATE_IP_PERIL, 11, 0, 0),
+ GATE(CLK_I2C4, "i2c4", "div_aclk_100", GATE_IP_PERIL, 10, 0, 0),
+ GATE(CLK_I2C3, "i2c3", "div_aclk_100", GATE_IP_PERIL, 9, 0, 0),
+ GATE(CLK_I2C2, "i2c2", "div_aclk_100", GATE_IP_PERIL, 8, 0, 0),
+ GATE(CLK_I2C1, "i2c1", "div_aclk_100", GATE_IP_PERIL, 7, 0, 0),
+ GATE(CLK_I2C0, "i2c0", "div_aclk_100", GATE_IP_PERIL, 6, 0, 0),
+ GATE(CLK_UART3, "uart3", "div_aclk_100", GATE_IP_PERIL, 3, 0, 0),
+ GATE(CLK_UART2, "uart2", "div_aclk_100", GATE_IP_PERIL, 2, 0, 0),
+ GATE(CLK_UART1, "uart1", "div_aclk_100", GATE_IP_PERIL, 1, 0, 0),
+ GATE(CLK_UART0, "uart0", "div_aclk_100", GATE_IP_PERIL, 0, 0, 0),
+};
+
+/*
+ * APLL & MPLL & BPLL & ISP_PLL & DISP_PLL & G3D_PLL
+ */
+static struct samsung_pll_rate_table exynos4415_pll_rates[] = {
+ PLL_35XX_RATE(1600000000, 400, 3, 1),
+ PLL_35XX_RATE(1500000000, 250, 2, 1),
+ PLL_35XX_RATE(1400000000, 175, 3, 0),
+ PLL_35XX_RATE(1300000000, 325, 3, 1),
+ PLL_35XX_RATE(1200000000, 400, 4, 1),
+ PLL_35XX_RATE(1100000000, 275, 3, 1),
+ PLL_35XX_RATE(1066000000, 533, 6, 1),
+ PLL_35XX_RATE(1000000000, 250, 3, 1),
+ PLL_35XX_RATE( 960000000, 320, 4, 1),
+ PLL_35XX_RATE( 900000000, 300, 4, 1),
+ PLL_35XX_RATE( 850000000, 425, 6, 1),
+ PLL_35XX_RATE( 800000000, 200, 3, 1),
+ PLL_35XX_RATE( 700000000, 175, 3, 1),
+ PLL_35XX_RATE( 667000000, 667, 12, 1),
+ PLL_35XX_RATE( 600000000, 400, 4, 2),
+ PLL_35XX_RATE( 550000000, 275, 3, 2),
+ PLL_35XX_RATE( 533000000, 533, 6, 2),
+ PLL_35XX_RATE( 520000000, 260, 3, 2),
+ PLL_35XX_RATE( 500000000, 250, 3, 2),
+ PLL_35XX_RATE( 440000000, 220, 3, 2),
+ PLL_35XX_RATE( 400000000, 200, 3, 2),
+ PLL_35XX_RATE( 350000000, 175, 3, 2),
+ PLL_35XX_RATE( 300000000, 300, 3, 3),
+ PLL_35XX_RATE( 266000000, 266, 3, 3),
+ PLL_35XX_RATE( 200000000, 200, 3, 3),
+ PLL_35XX_RATE( 160000000, 160, 3, 3),
+ PLL_35XX_RATE( 100000000, 200, 3, 4),
+ { /* sentinel */ }
+};
+
+/* EPLL */
+static struct samsung_pll_rate_table exynos4415_epll_rates[] = {
+ PLL_36XX_RATE(800000000, 200, 3, 1, 0),
+ PLL_36XX_RATE(288000000, 96, 2, 2, 0),
+ PLL_36XX_RATE(192000000, 128, 2, 3, 0),
+ PLL_36XX_RATE(144000000, 96, 2, 3, 0),
+ PLL_36XX_RATE( 96000000, 128, 2, 4, 0),
+ PLL_36XX_RATE( 84000000, 112, 2, 4, 0),
+ PLL_36XX_RATE( 80750011, 107, 2, 4, 43691),
+ PLL_36XX_RATE( 73728004, 98, 2, 4, 19923),
+ PLL_36XX_RATE( 67987602, 271, 3, 5, 62285),
+ PLL_36XX_RATE( 65911004, 175, 2, 5, 49982),
+ PLL_36XX_RATE( 50000000, 200, 3, 5, 0),
+ PLL_36XX_RATE( 49152003, 131, 2, 5, 4719),
+ PLL_36XX_RATE( 48000000, 128, 2, 5, 0),
+ PLL_36XX_RATE( 45250000, 181, 3, 5, 0),
+ { /* sentinel */ }
+};
+
+static struct samsung_pll_clock plls[nr_plls] __initdata = {
+ [apll] = PLL(pll_35xx, CLK_FOUT_APLL, "fout_apll", "fin_pll",
+ APLL_LOCK, APLL_CON0, NULL),
+ [epll] = PLL(pll_36xx, CLK_FOUT_EPLL, "fout_epll", "fin_pll",
+ EPLL_LOCK, EPLL_CON0, NULL),
+ [g3d_pll] = PLL(pll_35xx, CLK_FOUT_G3D_PLL, "fout_g3d_pll",
+ "mout_g3d_pllsrc", G3D_PLL_LOCK, G3D_PLL_CON0, NULL),
+ [isp_pll] = PLL(pll_35xx, CLK_FOUT_ISP_PLL, "fout_isp_pll", "fin_pll",
+ ISP_PLL_LOCK, ISP_PLL_CON0, NULL),
+ [disp_pll] = PLL(pll_35xx, CLK_FOUT_DISP_PLL, "fout_disp_pll",
+ "fin_pll", DISP_PLL_LOCK, DISP_PLL_CON0, NULL),
+};
+
+static void __init exynos4415_cmu_init(struct device_node *np)
+{
+ void __iomem *reg_base;
+
+ reg_base = of_iomap(np, 0);
+ if (!reg_base)
+ panic("%s: failed to map registers\n", __func__);
+
+ ctx = samsung_clk_init(np, reg_base, CLK_NR_CLKS);
+ if (!ctx)
+ panic("%s: unable to allocate context.\n", __func__);
+
+ plls[apll].rate_table = exynos4415_pll_rates;
+ plls[epll].rate_table = exynos4415_epll_rates;
+ plls[g3d_pll].rate_table = exynos4415_pll_rates;
+ plls[isp_pll].rate_table = exynos4415_pll_rates;
+ plls[disp_pll].rate_table = exynos4415_pll_rates;
+
+ samsung_clk_register_fixed_factor(ctx, fixed_factor_clks,
+ ARRAY_SIZE(fixed_factor_clks));
+ samsung_clk_register_fixed_rate(ctx, fixed_rate_clks,
+ ARRAY_SIZE(fixed_rate_clks));
+
+ samsung_clk_register_pll(ctx, plls, ARRAY_SIZE(plls), reg_base);
+ samsung_clk_register_mux(ctx, mux_clks, ARRAY_SIZE(mux_clks));
+ samsung_clk_register_div(ctx, div_clks, ARRAY_SIZE(div_clks));
+ samsung_clk_register_gate(ctx, gate_clks, ARRAY_SIZE(gate_clks));
+
+ exynos_clk_sleep_init();
+
+ samsung_clk_of_add_provider(np, ctx);
+}
+CLK_OF_DECLARE(exynos4415_cmu, "samsung,exynos4415-cmu", exynos4415_cmu_init);
+
+/*
+ * CMU DMC
+ */
+
+#define MPLL_LOCK 0x008
+#define MPLL_CON0 0x108
+#define MPLL_CON1 0x10c
+#define MPLL_CON2 0x110
+#define BPLL_LOCK 0x118
+#define BPLL_CON0 0x218
+#define BPLL_CON1 0x21c
+#define BPLL_CON2 0x220
+#define SRC_DMC 0x300
+#define DIV_DMC1 0x504
+
+enum exynos4415_dmc_plls {
+ mpll, bpll,
+ nr_dmc_plls,
+};
+
+#ifdef CONFIG_PM_SLEEP
+static struct samsung_clk_reg_dump *dmc_clk_regs;
+static struct samsung_clk_provider *dmc_ctx;
+
+static unsigned long dmc_save_list[] __initdata = {
+ MPLL_LOCK,
+ MPLL_CON0,
+ MPLL_CON1,
+ MPLL_CON2,
+ BPLL_LOCK,
+ BPLL_CON0,
+ BPLL_CON1,
+ BPLL_CON2,
+ SRC_DMC,
+ DIV_DMC1,
+};
+
+static int dmc_clk_suspend(void)
+{
+ samsung_clk_save(dmc_ctx->reg_base,
+ dmc_clk_regs, ARRAY_SIZE(dmc_save_list));
+ return 0;
+}
+
+static void dmc_clk_resume(void)
+{
+ samsung_clk_restore(dmc_ctx->reg_base,
+ dmc_clk_regs, ARRAY_SIZE(dmc_save_list));
+}
+
+static struct syscore_ops dmc_clk_syscore_ops = {
+ .suspend = dmc_clk_suspend,
+ .resume = dmc_clk_resume,
+};
+
+static void dmc_clk_sleep_init(void)
+{
+ dmc_clk_regs = samsung_clk_alloc_reg_dump(dmc_save_list,
+ ARRAY_SIZE(dmc_save_list));
+ if (!dmc_clk_regs) {
+ pr_warn("%s: Failed to allocate sleep save data\n", __func__);
+ return;
+ }
+
+ register_syscore_ops(&dmc_clk_syscore_ops);
+}
+#else
+static inline void dmc_clk_sleep_init(void) { }
+#endif /* CONFIG_PM_SLEEP */
+
+PNAME(mout_mpll_p) = { "fin_pll", "fout_mpll", };
+PNAME(mout_bpll_p) = { "fin_pll", "fout_bpll", };
+PNAME(mbpll_p) = { "mout_mpll", "mout_bpll", };
+
+static struct samsung_mux_clock dmc_mux_clks[] __initdata = {
+ MUX(CLK_DMC_MOUT_MPLL, "mout_mpll", mout_mpll_p, SRC_DMC, 12, 1),
+ MUX(CLK_DMC_MOUT_BPLL, "mout_bpll", mout_bpll_p, SRC_DMC, 10, 1),
+ MUX(CLK_DMC_MOUT_DPHY, "mout_dphy", mbpll_p, SRC_DMC, 8, 1),
+ MUX(CLK_DMC_MOUT_DMC_BUS, "mout_dmc_bus", mbpll_p, SRC_DMC, 4, 1),
+};
+
+static struct samsung_div_clock dmc_div_clks[] __initdata = {
+ DIV(CLK_DMC_DIV_DMC, "div_dmc", "div_dmc_pre", DIV_DMC1, 27, 3),
+ DIV(CLK_DMC_DIV_DPHY, "div_dphy", "mout_dphy", DIV_DMC1, 23, 3),
+ DIV(CLK_DMC_DIV_DMC_PRE, "div_dmc_pre", "mout_dmc_bus",
+ DIV_DMC1, 19, 2),
+ DIV(CLK_DMC_DIV_DMCP, "div_dmcp", "div_dmcd", DIV_DMC1, 15, 3),
+ DIV(CLK_DMC_DIV_DMCD, "div_dmcd", "div_dmc", DIV_DMC1, 11, 3),
+ DIV(CLK_DMC_DIV_MPLL_PRE, "div_mpll_pre", "mout_mpll", DIV_DMC1, 8, 2),
+};
+
+static struct samsung_pll_clock dmc_plls[nr_dmc_plls] __initdata = {
+ [mpll] = PLL(pll_35xx, CLK_DMC_FOUT_MPLL, "fout_mpll", "fin_pll",
+ MPLL_LOCK, MPLL_CON0, NULL),
+ [bpll] = PLL(pll_35xx, CLK_DMC_FOUT_BPLL, "fout_bpll", "fin_pll",
+ BPLL_LOCK, BPLL_CON0, NULL),
+};
+
+static void __init exynos4415_cmu_dmc_init(struct device_node *np)
+{
+ void __iomem *reg_base;
+
+ reg_base = of_iomap(np, 0);
+ if (!reg_base)
+ panic("%s: failed to map registers\n", __func__);
+
+ dmc_ctx = samsung_clk_init(np, reg_base, NR_CLKS_DMC);
+ if (!dmc_ctx)
+ panic("%s: unable to allocate context.\n", __func__);
+
+ dmc_plls[mpll].rate_table = exynos4415_pll_rates;
+ dmc_plls[bpll].rate_table = exynos4415_pll_rates;
+
+ samsung_clk_register_pll(dmc_ctx, dmc_plls,
+ ARRAY_SIZE(dmc_plls), reg_base);
+ samsung_clk_register_mux(dmc_ctx, dmc_mux_clks,
+ ARRAY_SIZE(dmc_mux_clks));
+ samsung_clk_register_div(dmc_ctx, dmc_div_clks,
+ ARRAY_SIZE(dmc_div_clks));
+
+ dmc_clk_sleep_init();
+
+ samsung_clk_of_add_provider(np, dmc_ctx);
+}
+CLK_OF_DECLARE(exynos4415_cmu_dmc, "samsung,exynos4415-cmu-dmc",
+ exynos4415_cmu_dmc_init);
diff --git a/include/dt-bindings/clock/exynos4415.h b/include/dt-bindings/clock/exynos4415.h
new file mode 100644
index 0000000..7eed551
--- /dev/null
+++ b/include/dt-bindings/clock/exynos4415.h
@@ -0,0 +1,360 @@
+/*
+ * Copyright (c) 2014 Samsung Electronics Co., Ltd.
+ * Author: Chanwoo Choi <cw00.choi@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Device Tree binding constants for Samsung Exynos4415 clock controllers.
+ */
+
+#ifndef _DT_BINDINGS_CLOCK_SAMSUNG_EXYNOS4415_CLOCK_H
+#define _DT_BINDINGS_CLOCK_SAMSUNG_EXYNOS4415_CLOCK_H
+
+/*
+ * Let each exported clock get a unique index, which is used on DT-enabled
+ * platforms to lookup the clock from a clock specifier. These indices are
+ * therefore considered an ABI and so must not be changed. This implies
+ * that new clocks should be added either in free spaces between clock groups
+ * or at the end.
+ */
+
+/*
+ * Main CMU
+ */
+
+#define CLK_OSCSEL 1
+#define CLK_FIN_PLL 2
+#define CLK_FOUT_APLL 3
+#define CLK_FOUT_MPLL 4
+#define CLK_FOUT_EPLL 5
+#define CLK_FOUT_G3D_PLL 6
+#define CLK_FOUT_ISP_PLL 7
+#define CLK_FOUT_DISP_PLL 8
+
+/* Muxes */
+#define CLK_MOUT_MPLL_USER_L 16
+#define CLK_MOUT_GDL 17
+#define CLK_MOUT_MPLL_USER_R 18
+#define CLK_MOUT_GDR 19
+#define CLK_MOUT_EBI 20
+#define CLK_MOUT_ACLK_200 21
+#define CLK_MOUT_ACLK_160 22
+#define CLK_MOUT_ACLK_100 23
+#define CLK_MOUT_ACLK_266 24
+#define CLK_MOUT_G3D_PLL 25
+#define CLK_MOUT_EPLL 26
+#define CLK_MOUT_EBI_1 27
+#define CLK_MOUT_ISP_PLL 28
+#define CLK_MOUT_DISP_PLL 29
+#define CLK_MOUT_MPLL_USER_T 30
+#define CLK_MOUT_ACLK_400_MCUISP 31
+#define CLK_MOUT_G3D_PLLSRC 32
+#define CLK_MOUT_CSIS1 33
+#define CLK_MOUT_CSIS0 34
+#define CLK_MOUT_CAM1 35
+#define CLK_MOUT_FIMC3_LCLK 36
+#define CLK_MOUT_FIMC2_LCLK 37
+#define CLK_MOUT_FIMC1_LCLK 38
+#define CLK_MOUT_FIMC0_LCLK 39
+#define CLK_MOUT_MFC 40
+#define CLK_MOUT_MFC_1 41
+#define CLK_MOUT_MFC_0 42
+#define CLK_MOUT_G3D 43
+#define CLK_MOUT_G3D_1 44
+#define CLK_MOUT_G3D_0 45
+#define CLK_MOUT_MIPI0 46
+#define CLK_MOUT_FIMD0 47
+#define CLK_MOUT_TSADC_ISP 48
+#define CLK_MOUT_UART_ISP 49
+#define CLK_MOUT_SPI1_ISP 50
+#define CLK_MOUT_SPI0_ISP 51
+#define CLK_MOUT_PWM_ISP 52
+#define CLK_MOUT_AUDIO0 53
+#define CLK_MOUT_TSADC 54
+#define CLK_MOUT_MMC2 55
+#define CLK_MOUT_MMC1 56
+#define CLK_MOUT_MMC0 57
+#define CLK_MOUT_UART3 58
+#define CLK_MOUT_UART2 59
+#define CLK_MOUT_UART1 60
+#define CLK_MOUT_UART0 61
+#define CLK_MOUT_SPI2 62
+#define CLK_MOUT_SPI1 63
+#define CLK_MOUT_SPI0 64
+#define CLK_MOUT_SPDIF 65
+#define CLK_MOUT_AUDIO2 66
+#define CLK_MOUT_AUDIO1 67
+#define CLK_MOUT_MPLL_USER_C 68
+#define CLK_MOUT_HPM 69
+#define CLK_MOUT_CORE 70
+#define CLK_MOUT_APLL 71
+#define CLK_MOUT_PXLASYNC_CSIS1_FIMC 72
+#define CLK_MOUT_PXLASYNC_CSIS0_FIMC 73
+#define CLK_MOUT_JPEG 74
+#define CLK_MOUT_JPEG1 75
+#define CLK_MOUT_JPEG0 76
+#define CLK_MOUT_ACLK_ISP0_300 77
+#define CLK_MOUT_ACLK_ISP0_400 78
+#define CLK_MOUT_ACLK_ISP0_300_USER 79
+#define CLK_MOUT_ACLK_ISP1_300 80
+#define CLK_MOUT_ACLK_ISP1_300_USER 81
+#define CLK_MOUT_HDMI 82
+
+/* Dividers */
+#define CLK_DIV_GPL 90
+#define CLK_DIV_GDL 91
+#define CLK_DIV_GPR 92
+#define CLK_DIV_GDR 93
+#define CLK_DIV_ACLK_400_MCUISP 94
+#define CLK_DIV_EBI 95
+#define CLK_DIV_ACLK_200 96
+#define CLK_DIV_ACLK_160 97
+#define CLK_DIV_ACLK_100 98
+#define CLK_DIV_ACLK_266 99
+#define CLK_DIV_CSIS1 100
+#define CLK_DIV_CSIS0 101
+#define CLK_DIV_CAM1 102
+#define CLK_DIV_FIMC3_LCLK 103
+#define CLK_DIV_FIMC2_LCLK 104
+#define CLK_DIV_FIMC1_LCLK 105
+#define CLK_DIV_FIMC0_LCLK 106
+#define CLK_DIV_TV_BLK 107
+#define CLK_DIV_MFC 108
+#define CLK_DIV_G3D 109
+#define CLK_DIV_MIPI0_PRE 110
+#define CLK_DIV_MIPI0 111
+#define CLK_DIV_FIMD0 112
+#define CLK_DIV_UART_ISP 113
+#define CLK_DIV_SPI1_ISP_PRE 114
+#define CLK_DIV_SPI1_ISP 115
+#define CLK_DIV_SPI0_ISP_PRE 116
+#define CLK_DIV_SPI0_ISP 117
+#define CLK_DIV_PWM_ISP 118
+#define CLK_DIV_PCM0 119
+#define CLK_DIV_AUDIO0 120
+#define CLK_DIV_TSADC_PRE 121
+#define CLK_DIV_TSADC 122
+#define CLK_DIV_MMC1_PRE 123
+#define CLK_DIV_MMC1 124
+#define CLK_DIV_MMC0_PRE 125
+#define CLK_DIV_MMC0 126
+#define CLK_DIV_MMC2_PRE 127
+#define CLK_DIV_MMC2 128
+#define CLK_DIV_UART3 129
+#define CLK_DIV_UART2 130
+#define CLK_DIV_UART1 131
+#define CLK_DIV_UART0 132
+#define CLK_DIV_SPI1_PRE 133
+#define CLK_DIV_SPI1 134
+#define CLK_DIV_SPI0_PRE 135
+#define CLK_DIV_SPI0 136
+#define CLK_DIV_SPI2_PRE 137
+#define CLK_DIV_SPI2 138
+#define CLK_DIV_PCM2 139
+#define CLK_DIV_AUDIO2 140
+#define CLK_DIV_PCM1 141
+#define CLK_DIV_AUDIO1 142
+#define CLK_DIV_I2S1 143
+#define CLK_DIV_PXLASYNC_CSIS1_FIMC 144
+#define CLK_DIV_PXLASYNC_CSIS0_FIMC 145
+#define CLK_DIV_JPEG 146
+#define CLK_DIV_CORE2 147
+#define CLK_DIV_APLL 148
+#define CLK_DIV_PCLK_DBG 149
+#define CLK_DIV_ATB 150
+#define CLK_DIV_PERIPH 151
+#define CLK_DIV_COREM1 152
+#define CLK_DIV_COREM0 153
+#define CLK_DIV_CORE 154
+#define CLK_DIV_HPM 155
+#define CLK_DIV_COPY 156
+
+/* Gates */
+#define CLK_ASYNC_G3D 180
+#define CLK_ASYNC_MFCL 181
+#define CLK_ASYNC_TVX 182
+#define CLK_PPMULEFT 183
+#define CLK_GPIO_LEFT 184
+#define CLK_PPMUIMAGE 185
+#define CLK_QEMDMA2 186
+#define CLK_QEROTATOR 187
+#define CLK_SMMUMDMA2 188
+#define CLK_SMMUROTATOR 189
+#define CLK_MDMA2 190
+#define CLK_ROTATOR 191
+#define CLK_ASYNC_ISPMX 192
+#define CLK_ASYNC_MAUDIOX 193
+#define CLK_ASYNC_MFCR 194
+#define CLK_ASYNC_FSYSD 195
+#define CLK_ASYNC_LCD0X 196
+#define CLK_ASYNC_CAMX 197
+#define CLK_PPMURIGHT 198
+#define CLK_GPIO_RIGHT 199
+#define CLK_ANTIRBK_APBIF 200
+#define CLK_EFUSE_WRITER_APBIF 201
+#define CLK_MONOCNT 202
+#define CLK_TZPC6 203
+#define CLK_PROVISIONKEY1 204
+#define CLK_PROVISIONKEY0 205
+#define CLK_CMU_ISPPART 206
+#define CLK_TMU_APBIF 207
+#define CLK_KEYIF 208
+#define CLK_RTC 209
+#define CLK_WDT 210
+#define CLK_MCT 211
+#define CLK_SECKEY 212
+#define CLK_HDMI_CEC 213
+#define CLK_TZPC5 214
+#define CLK_TZPC4 215
+#define CLK_TZPC3 216
+#define CLK_TZPC2 217
+#define CLK_TZPC1 218
+#define CLK_TZPC0 219
+#define CLK_CMU_COREPART 220
+#define CLK_CMU_TOPPART 221
+#define CLK_PMU_APBIF 222
+#define CLK_SYSREG 223
+#define CLK_CHIP_ID 224
+#define CLK_SMMUFIMC_LITE2 225
+#define CLK_FIMC_LITE2 226
+#define CLK_PIXELASYNCM1 227
+#define CLK_PIXELASYNCM0 228
+#define CLK_PPMUCAMIF 229
+#define CLK_SMMUJPEG 230
+#define CLK_SMMUFIMC3 231
+#define CLK_SMMUFIMC2 232
+#define CLK_SMMUFIMC1 233
+#define CLK_SMMUFIMC0 234
+#define CLK_JPEG 235
+#define CLK_CSIS1 236
+#define CLK_CSIS0 237
+#define CLK_FIMC3 238
+#define CLK_FIMC2 239
+#define CLK_FIMC1 240
+#define CLK_FIMC0 241
+#define CLK_PPMUTV 242
+#define CLK_SMMUTV 243
+#define CLK_HDMI 244
+#define CLK_MIXER 245
+#define CLK_VP 246
+#define CLK_PPMUMFC_R 247
+#define CLK_PPMUMFC_L 248
+#define CLK_SMMUMFC_R 249
+#define CLK_SMMUMFC_L 250
+#define CLK_MFC 251
+#define CLK_PPMUG3D 252
+#define CLK_G3D 253
+#define CLK_PPMULCD0 254
+#define CLK_SMMUFIMD0 255
+#define CLK_DSIM0 256
+#define CLK_SMIES 257
+#define CLK_MIE0 258
+#define CLK_FIMD0 259
+#define CLK_TSADC 260
+#define CLK_PPMUFILE 261
+#define CLK_NFCON 262
+#define CLK_USBDEVICE 263
+#define CLK_USBHOST 264
+#define CLK_SROMC 265
+#define CLK_SDMMC2 266
+#define CLK_SDMMC1 267
+#define CLK_SDMMC0 268
+#define CLK_PDMA1 269
+#define CLK_PDMA0 270
+#define CLK_SPDIF 271
+#define CLK_PWM 272
+#define CLK_PCM2 273
+#define CLK_PCM1 274
+#define CLK_I2S1 275
+#define CLK_SPI2 276
+#define CLK_SPI1 277
+#define CLK_SPI0 278
+#define CLK_I2CHDMI 279
+#define CLK_I2C7 280
+#define CLK_I2C6 281
+#define CLK_I2C5 282
+#define CLK_I2C4 283
+#define CLK_I2C3 284
+#define CLK_I2C2 285
+#define CLK_I2C1 286
+#define CLK_I2C0 287
+#define CLK_UART3 288
+#define CLK_UART2 289
+#define CLK_UART1 290
+#define CLK_UART0 291
+
+/* Special clocks */
+#define CLK_SCLK_PXLAYSNC_CSIS1_FIMC 330
+#define CLK_SCLK_PXLAYSNC_CSIS0_FIMC 331
+#define CLK_SCLK_JPEG 332
+#define CLK_SCLK_CSIS1 333
+#define CLK_SCLK_CSIS0 334
+#define CLK_SCLK_CAM1 335
+#define CLK_SCLK_FIMC3_LCLK 336
+#define CLK_SCLK_FIMC2_LCLK 337
+#define CLK_SCLK_FIMC1_LCLK 338
+#define CLK_SCLK_FIMC0_LCLK 339
+#define CLK_SCLK_PIXEL 340
+#define CLK_SCLK_HDMI 341
+#define CLK_SCLK_MIXER 342
+#define CLK_SCLK_MFC 343
+#define CLK_SCLK_G3D 344
+#define CLK_SCLK_MIPIDPHY4L 345
+#define CLK_SCLK_MIPI0 346
+#define CLK_SCLK_MDNIE0 347
+#define CLK_SCLK_FIMD0 348
+#define CLK_SCLK_PCM0 349
+#define CLK_SCLK_AUDIO0 350
+#define CLK_SCLK_TSADC 351
+#define CLK_SCLK_EBI 352
+#define CLK_SCLK_MMC2 353
+#define CLK_SCLK_MMC1 354
+#define CLK_SCLK_MMC0 355
+#define CLK_SCLK_I2S 356
+#define CLK_SCLK_PCM2 357
+#define CLK_SCLK_PCM1 358
+#define CLK_SCLK_AUDIO2 359
+#define CLK_SCLK_AUDIO1 360
+#define CLK_SCLK_SPDIF 361
+#define CLK_SCLK_SPI2 362
+#define CLK_SCLK_SPI1 363
+#define CLK_SCLK_SPI0 364
+#define CLK_SCLK_UART3 365
+#define CLK_SCLK_UART2 366
+#define CLK_SCLK_UART1 367
+#define CLK_SCLK_UART0 368
+#define CLK_SCLK_HDMIPHY 369
+
+/*
+ * Total number of clocks of main CMU.
+ * NOTE: Must be equal to last clock ID increased by one.
+ */
+#define CLK_NR_CLKS 370
+
+/*
+ * CMU DMC
+ */
+#define CLK_DMC_FOUT_MPLL 1
+#define CLK_DMC_FOUT_BPLL 2
+
+#define CLK_DMC_MOUT_MPLL 3
+#define CLK_DMC_MOUT_BPLL 4
+#define CLK_DMC_MOUT_DPHY 5
+#define CLK_DMC_MOUT_DMC_BUS 6
+
+#define CLK_DMC_DIV_DMC 7
+#define CLK_DMC_DIV_DPHY 8
+#define CLK_DMC_DIV_DMC_PRE 9
+#define CLK_DMC_DIV_DMCP 10
+#define CLK_DMC_DIV_DMCD 11
+#define CLK_DMC_DIV_MPLL_PRE 12
+
+/*
+ * Total number of clocks of CMU_DMC.
+ * NOTE: Must be equal to highest clock ID increased by one.
+ */
+#define NR_CLKS_DMC 13
+
+#endif /* _DT_BINDINGS_CLOCK_SAMSUNG_EXYNOS4415_CLOCK_H */
--
1.8.0
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH 3/5] clk: samsung: Document binding for Exynos4415 clock controller
2014-10-20 3:29 [PATCH 0/5] Support new Exynos4415 SoC based on Cortex-A9 quad cores Chanwoo Choi
2014-10-20 3:32 ` [PATCH 1/5] ARM: EXYNOS: Add EXYNOS4415 SoC ID Chanwoo Choi
2014-10-20 3:32 ` [PATCH 2/5] clk: samsung: exynos4415: Add clocks using common clock framework Chanwoo Choi
@ 2014-10-20 3:32 ` Chanwoo Choi
2014-10-24 10:32 ` Sylwester Nawrocki
2014-10-20 3:32 ` [PATCH 4/5] pinctrl: exynos: Add support for Exynos4415 Chanwoo Choi
2014-10-20 3:32 ` [PATCH 5/5] ARM: dts: Add dts files for Exynos4415 SoC Chanwoo Choi
4 siblings, 1 reply; 21+ messages in thread
From: Chanwoo Choi @ 2014-10-20 3:32 UTC (permalink / raw)
To: linux-samsung-soc, linux-kernel, linux-arm-kernel
Cc: kgene.kim, ben-linux, linux, mark.rutland, arnd, olof,
tomasz.figa, mturquette, thomas.abraham, linus.walleij,
sw0312.kim, kyungmin.park, inki.dae, geunsik.lim, jh80.chung,
cw00.choi, jaewon02.kim, ideal.song, yj44.cho,
Sylwester Nawrocki
The Exynos4415 clocks are statically listed and registered using the
Samsung specific common clock helper functions. Both device tree based
clock lookup and clkdev based clock lookups are supported.
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
---
.../devicetree/bindings/clock/exynos4415-clock.txt | 49 ++++++++++++++++++++++
1 file changed, 49 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/exynos4415-clock.txt
diff --git a/Documentation/devicetree/bindings/clock/exynos4415-clock.txt b/Documentation/devicetree/bindings/clock/exynos4415-clock.txt
new file mode 100644
index 0000000..8aa4f4f
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/exynos4415-clock.txt
@@ -0,0 +1,49 @@
+* Samsung Exynos4415 Clock Controller
+
+The Exynos4415 clock controller generates and supplies clock to various
+controllers within the Exynos4415 SoC.
+
+Required Properties:
+
+- compatible: should be one of the following.
+ - "samsung,exynos4415-cmu" - controller compatible with Exynos4415 SoC.
+ - "samsung,exynos4415-cmu-dmc" - controller compatible with
+ Exynos4415 SoC for Dynamic Memory Controller domain.
+
+- reg: physical base address of the controller and length of memory mapped
+ region.
+
+- #clock-cells: should be 1.
+
+Each clock is assigned an identifier and client nodes can use this identifier
+to specify the clock which they consume.
+
+All available clocks are defined as preprocessor macros in
+dt-bindings/clock/exynos4415.h header and can be used in device
+tree sources.
+
+Example 1: An example of a clock controller node is listed below.
+
+ cmu: clock-controller@10030000 {
+ compatible = "samsung,exynos4415-cmu";
+ reg = <0x10030000 0x18000>;
+ #clock-cells = <1>;
+ };
+
+ cmu-dmc: clock-controller@105C0000 {
+ compatible = "samsung,exynos4415-cmu-dmc";
+ reg = <0x105C0000 0x3000>;
+ #clock-cells = <1>;
+ };
+
+Example 2: UART controller node that consumes the clock generated by the clock
+ controller. Refer to the standard clock bindings for information
+ about 'clocks' and 'clock-names' property.
+
+ serial_0: serial@13800000 {
+ compatible = "samsung,exynos4210-uart";
+ reg = <0x13800000 0x100>;
+ interrupts = <0 109 0>;
+ clocks = <&cmu CLK_UART0>, <&cmu CLK_SCLK_UART0>;
+ clock-names = "uart", "clk_uart_baud0";
+ };
--
1.8.0
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH 4/5] pinctrl: exynos: Add support for Exynos4415
2014-10-20 3:29 [PATCH 0/5] Support new Exynos4415 SoC based on Cortex-A9 quad cores Chanwoo Choi
` (2 preceding siblings ...)
2014-10-20 3:32 ` [PATCH 3/5] clk: samsung: Document binding for Exynos4415 clock controller Chanwoo Choi
@ 2014-10-20 3:32 ` Chanwoo Choi
2014-10-20 3:32 ` [PATCH 5/5] ARM: dts: Add dts files for Exynos4415 SoC Chanwoo Choi
4 siblings, 0 replies; 21+ messages in thread
From: Chanwoo Choi @ 2014-10-20 3:32 UTC (permalink / raw)
To: linux-samsung-soc, linux-kernel, linux-arm-kernel
Cc: kgene.kim, ben-linux, linux, mark.rutland, arnd, olof,
tomasz.figa, mturquette, thomas.abraham, linus.walleij,
sw0312.kim, kyungmin.park, inki.dae, geunsik.lim, jh80.chung,
cw00.choi, jaewon02.kim, ideal.song, yj44.cho
From: Tomasz Figa <tomasz.figa@gmail.com>
The pin controllers of Exynos4415 are similar to Exynos4412, but certain
differences cause the need to create separate driver data for it. This
patch adds pin controller and bank descriptor arrays to the driver to
support the new SoC.
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
[cw00.choi: Rebase it on mainline kernel]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
---
drivers/pinctrl/samsung/pinctrl-exynos.c | 78 +++++++++++++++++++++++++++++++
drivers/pinctrl/samsung/pinctrl-samsung.c | 2 +
drivers/pinctrl/samsung/pinctrl-samsung.h | 1 +
3 files changed, 81 insertions(+)
diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c b/drivers/pinctrl/samsung/pinctrl-exynos.c
index d7154ed..065eee0 100644
--- a/drivers/pinctrl/samsung/pinctrl-exynos.c
+++ b/drivers/pinctrl/samsung/pinctrl-exynos.c
@@ -920,6 +920,84 @@ struct samsung_pin_ctrl exynos4x12_pin_ctrl[] = {
},
};
+/* pin banks of exynos4415 pin-controller 0 */
+static struct samsung_pin_bank exynos4415_pin_banks0[] = {
+ EXYNOS_PIN_BANK_EINTG(8, 0x000, "gpa0", 0x00),
+ EXYNOS_PIN_BANK_EINTG(6, 0x020, "gpa1", 0x04),
+ EXYNOS_PIN_BANK_EINTG(8, 0x040, "gpb", 0x08),
+ EXYNOS_PIN_BANK_EINTG(5, 0x060, "gpc0", 0x0c),
+ EXYNOS_PIN_BANK_EINTG(5, 0x080, "gpc1", 0x10),
+ EXYNOS_PIN_BANK_EINTG(4, 0x0A0, "gpd0", 0x14),
+ EXYNOS_PIN_BANK_EINTG(4, 0x0C0, "gpd1", 0x18),
+ EXYNOS_PIN_BANK_EINTG(8, 0x180, "gpf0", 0x30),
+ EXYNOS_PIN_BANK_EINTG(8, 0x1A0, "gpf1", 0x34),
+ EXYNOS_PIN_BANK_EINTG(1, 0x1C0, "gpf2", 0x38),
+};
+
+/* pin banks of exynos4415 pin-controller 1 */
+static struct samsung_pin_bank exynos4415_pin_banks1[] = {
+ EXYNOS_PIN_BANK_EINTG(8, 0x040, "gpk0", 0x08),
+ EXYNOS_PIN_BANK_EINTG(7, 0x060, "gpk1", 0x0c),
+ EXYNOS_PIN_BANK_EINTG(7, 0x080, "gpk2", 0x10),
+ EXYNOS_PIN_BANK_EINTG(7, 0x0A0, "gpk3", 0x14),
+ EXYNOS_PIN_BANK_EINTG(4, 0x0C0, "gpl0", 0x18),
+ EXYNOS_PIN_BANK_EINTN(6, 0x120, "mp00"),
+ EXYNOS_PIN_BANK_EINTN(4, 0x140, "mp01"),
+ EXYNOS_PIN_BANK_EINTN(6, 0x160, "mp02"),
+ EXYNOS_PIN_BANK_EINTN(8, 0x180, "mp03"),
+ EXYNOS_PIN_BANK_EINTN(8, 0x1A0, "mp04"),
+ EXYNOS_PIN_BANK_EINTN(8, 0x1C0, "mp05"),
+ EXYNOS_PIN_BANK_EINTN(8, 0x1E0, "mp06"),
+ EXYNOS_PIN_BANK_EINTG(8, 0x260, "gpm0", 0x24),
+ EXYNOS_PIN_BANK_EINTG(7, 0x280, "gpm1", 0x28),
+ EXYNOS_PIN_BANK_EINTG(5, 0x2A0, "gpm2", 0x2c),
+ EXYNOS_PIN_BANK_EINTG(8, 0x2C0, "gpm3", 0x30),
+ EXYNOS_PIN_BANK_EINTG(8, 0x2E0, "gpm4", 0x34),
+ EXYNOS_PIN_BANK_EINTW(8, 0xC00, "gpx0", 0x00),
+ EXYNOS_PIN_BANK_EINTW(8, 0xC20, "gpx1", 0x04),
+ EXYNOS_PIN_BANK_EINTW(8, 0xC40, "gpx2", 0x08),
+ EXYNOS_PIN_BANK_EINTW(8, 0xC60, "gpx3", 0x0c),
+};
+
+/* pin banks of exynos4415 pin-controller 2 */
+static struct samsung_pin_bank exynos4415_pin_banks2[] = {
+ EXYNOS_PIN_BANK_EINTG(7, 0x000, "gpz", 0x00),
+ EXYNOS_PIN_BANK_EINTN(2, 0x000, "etc1"),
+};
+
+/*
+ * Samsung pinctrl driver data for Exynos4415 SoC. Exynos4415 SoC includes
+ * three gpio/pin-mux/pinconfig controllers.
+ */
+struct samsung_pin_ctrl exynos4415_pin_ctrl[] = {
+ {
+ /* pin-controller instance 0 data */
+ .pin_banks = exynos4415_pin_banks0,
+ .nr_banks = ARRAY_SIZE(exynos4415_pin_banks0),
+ .eint_gpio_init = exynos_eint_gpio_init,
+ .suspend = exynos_pinctrl_suspend,
+ .resume = exynos_pinctrl_resume,
+ .label = "exynos4415-gpio-ctrl0",
+ }, {
+ /* pin-controller instance 1 data */
+ .pin_banks = exynos4415_pin_banks1,
+ .nr_banks = ARRAY_SIZE(exynos4415_pin_banks1),
+ .eint_gpio_init = exynos_eint_gpio_init,
+ .eint_wkup_init = exynos_eint_wkup_init,
+ .suspend = exynos_pinctrl_suspend,
+ .resume = exynos_pinctrl_resume,
+ .label = "exynos4415-gpio-ctrl1",
+ }, {
+ /* pin-controller instance 2 data */
+ .pin_banks = exynos4415_pin_banks2,
+ .nr_banks = ARRAY_SIZE(exynos4415_pin_banks2),
+ .eint_gpio_init = exynos_eint_gpio_init,
+ .suspend = exynos_pinctrl_suspend,
+ .resume = exynos_pinctrl_resume,
+ .label = "exynos4415-gpio-ctrl2",
+ },
+};
+
/* pin banks of exynos5250 pin-controller 0 */
static struct samsung_pin_bank exynos5250_pin_banks0[] = {
EXYNOS_PIN_BANK_EINTG(8, 0x000, "gpa0", 0x00),
diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c b/drivers/pinctrl/samsung/pinctrl-samsung.c
index b07406d..0397ce5 100644
--- a/drivers/pinctrl/samsung/pinctrl-samsung.c
+++ b/drivers/pinctrl/samsung/pinctrl-samsung.c
@@ -1224,6 +1224,8 @@ static const struct of_device_id samsung_pinctrl_dt_match[] = {
.data = (void *)exynos4210_pin_ctrl },
{ .compatible = "samsung,exynos4x12-pinctrl",
.data = (void *)exynos4x12_pin_ctrl },
+ { .compatible = "samsung,exynos4415-pinctrl",
+ .data = (void *)exynos4415_pin_ctrl },
{ .compatible = "samsung,exynos5250-pinctrl",
.data = (void *)exynos5250_pin_ctrl },
{ .compatible = "samsung,exynos5260-pinctrl",
diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.h b/drivers/pinctrl/samsung/pinctrl-samsung.h
index 5cedc9d..10b720d 100644
--- a/drivers/pinctrl/samsung/pinctrl-samsung.h
+++ b/drivers/pinctrl/samsung/pinctrl-samsung.h
@@ -239,6 +239,7 @@ struct samsung_pmx_func {
extern struct samsung_pin_ctrl exynos3250_pin_ctrl[];
extern struct samsung_pin_ctrl exynos4210_pin_ctrl[];
extern struct samsung_pin_ctrl exynos4x12_pin_ctrl[];
+extern struct samsung_pin_ctrl exynos4415_pin_ctrl[];
extern struct samsung_pin_ctrl exynos5250_pin_ctrl[];
extern struct samsung_pin_ctrl exynos5260_pin_ctrl[];
extern struct samsung_pin_ctrl exynos5420_pin_ctrl[];
--
1.8.0
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH 5/5] ARM: dts: Add dts files for Exynos4415 SoC
2014-10-20 3:29 [PATCH 0/5] Support new Exynos4415 SoC based on Cortex-A9 quad cores Chanwoo Choi
` (3 preceding siblings ...)
2014-10-20 3:32 ` [PATCH 4/5] pinctrl: exynos: Add support for Exynos4415 Chanwoo Choi
@ 2014-10-20 3:32 ` Chanwoo Choi
2014-10-24 13:23 ` Daniel Drake
4 siblings, 1 reply; 21+ messages in thread
From: Chanwoo Choi @ 2014-10-20 3:32 UTC (permalink / raw)
To: linux-samsung-soc, linux-kernel, linux-arm-kernel
Cc: kgene.kim, ben-linux, linux, mark.rutland, arnd, olof,
tomasz.figa, mturquette, thomas.abraham, linus.walleij,
sw0312.kim, kyungmin.park, inki.dae, geunsik.lim, jh80.chung,
cw00.choi, jaewon02.kim, ideal.song, yj44.cho, Marek Szyprowski
This patch adds new exynos4415.dtsi to support Exynos4415 SoC
based on Cortex-A9 quad cores and includes following dt nodes:
- GIC interrupt controller (GIC-400)
- Pinctrl to control three GPIO parts
- CMU (Clock Management Unit) for CMU/CMU_DMC/AUDSS
- CPU information (Cortex-A9 quad cores)
- UART to support serial port
- MCT (Multi Core Timer)
- ADC (Analog Digital Converter)
- RTC (Real Time Clock)
- I2C/SPI busses
- Power domains (CAM, TV, MFC, G3D, LCD0, ISP0/1)
- PMU (Performance Monitoring Unit)
- MSHC (Mobile Storage Host Controller)
- EHCI (Enhanced Host Controller Interface)
- OHIC (Open Host Controller Interface)
- USB 2.0 device with hsotg
- PWM (Pluse Width Modulation) Timer
- AMBA bus for PDMA0/1
- SYSRAM node for memory mapping
- SYSREG node for memory mapping
- PMU (Power Management Unit) node for memory mapping
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
[m.szyprowski: Add OHCI node and correct EHCI node]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
[yj44.cho: Add mipi-phy node]
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
[jaewon02: Add EHCI and SPI_2 node]
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
[ideal.song: Add I2S0 node for audio interface]
Signed-off-by: Inha Song <ideal.song@samsung.com>
[tomasz.figa: Add L2 cache node]
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Kyungmin Park <Kyungmin Park@samsung.com>
---
arch/arm/boot/dts/exynos4415-pinctrl.dtsi | 613 +++++++++++++++++++++++++++++
arch/arm/boot/dts/exynos4415.dtsi | 627 ++++++++++++++++++++++++++++++
2 files changed, 1240 insertions(+)
create mode 100644 arch/arm/boot/dts/exynos4415-pinctrl.dtsi
create mode 100644 arch/arm/boot/dts/exynos4415.dtsi
diff --git a/arch/arm/boot/dts/exynos4415-pinctrl.dtsi b/arch/arm/boot/dts/exynos4415-pinctrl.dtsi
new file mode 100644
index 0000000..5ce4314
--- /dev/null
+++ b/arch/arm/boot/dts/exynos4415-pinctrl.dtsi
@@ -0,0 +1,613 @@
+/*
+ * Samsung's Exynos4415 SoCs pin-mux and pin-config device tree source
+ *
+ * Copyright (c) 2014 Samsung Electronics Co., Ltd.
+ *
+ * Samsung's Exynos4415 SoCs pin-mux and pin-config optiosn are listed as device
+ * tree nodes are listed in this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+&pinctrl_0 {
+ gpa0: gpa0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpa1: gpa1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpb: gpb {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpc0: gpc0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpc1: gpc1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpd0: gpd0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpd1: gpd1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpf0: gpf0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpf1: gpf1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpf2: gpf2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ uart0_data: uart0-data {
+ samsung,pins = "gpa0-0", "gpa0-1";
+ samsung,pin-function = <0x2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ uart0_fctl: uart0-fctl {
+ samsung,pins = "gpa0-2", "gpa0-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ uart1_data: uart1-data {
+ samsung,pins = "gpa0-4", "gpa0-5";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ uart1_fctl: uart1-fctl {
+ samsung,pins = "gpa0-6", "gpa0-7";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ uart2_data: uart2-data {
+ samsung,pins = "gpa1-0", "gpa1-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ uart2_fctl: uart2-fctl {
+ samsung,pins = "gpa1-2", "gpa1-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ uart3_data: uart3-data {
+ samsung,pins = "gpa1-4", "gpa1-5";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c2_bus: i2c2-bus {
+ samsung,pins = "gpa0-6", "gpa0-7";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c3_bus: i2c3-bus {
+ samsung,pins = "gpa1-2", "gpa1-3";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ spi0_bus: spi0-bus {
+ samsung,pins = "gpb-0", "gpb-2", "gpb-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c4_bus: i2c4-bus {
+ samsung,pins = "gpb-0", "gpb-1";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ spi1_bus: spi1-bus {
+ samsung,pins = "gpb-4", "gpb-6", "gpb-7";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c5_bus: i2c5-bus {
+ samsung,pins = "gpb-2", "gpb-3";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2s1_bus: i2s1-bus {
+ samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
+ "gpc0-4";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2s2_bus: i2s2-bus {
+ samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
+ "gpc1-4";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ pcm2_bus: pcm2-bus {
+ samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
+ "gpc1-4";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c6_bus: i2c6-bus {
+ samsung,pins = "gpc1-3", "gpc1-4";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ spi2_bus: spi2-bus {
+ samsung,pins = "gpc1-1", "gpc1-3", "gpc1-4";
+ samsung,pin-function = <5>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ pwm0_out: pwm0-out {
+ samsung,pins = "gpd0-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ pwm1_out: pwm1-out {
+ samsung,pins = "gpd0-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ pwm2_out: pwm2-out {
+ samsung,pins = "gpd0-2";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ pwm3_out: pwm3-out {
+ samsung,pins = "gpd0-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c7_bus: i2c7-bus {
+ samsung,pins = "gpd0-2", "gpd0-3";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c0_bus: i2c0-bus {
+ samsung,pins = "gpd1-0", "gpd1-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c1_bus: i2c1-bus {
+ samsung,pins = "gpd1-2", "gpd1-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&pinctrl_1 {
+ gpk0: gpk0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpk1: gpk1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpk2: gpk2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpk3: gpk3 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpl0: gpl0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ mp00: mp00 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ mp01: mp01 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ mp02: mp02 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ mp03: mp03 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ mp04: mp04 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ mp05: mp05 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ mp06: mp06 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ gpm0: gpm0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpm1: gpm1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpm2: gpm2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpm3: gpm3 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpm4: gpm4 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpx0: gpx0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ interrupt-parent = <&gic>;
+ interrupts = <0 32 0>, <0 33 0>, <0 34 0>, <0 35 0>,
+ <0 36 0>, <0 37 0>, <0 38 0>, <0 39 0>;
+ #interrupt-cells = <2>;
+ };
+
+ gpx1: gpx1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ interrupt-parent = <&gic>;
+ interrupts = <0 40 0>, <0 41 0>, <0 42 0>, <0 43 0>,
+ <0 44 0>, <0 45 0>, <0 46 0>, <0 47 0>;
+ #interrupt-cells = <2>;
+ };
+
+ gpx2: gpx2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpx3: gpx3 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ sd0_clk: sd0-clk {
+ samsung,pins = "gpk0-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_cmd: sd0-cmd {
+ samsung,pins = "gpk0-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_cd: sd0-cd {
+ samsung,pins = "gpk0-2";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_rdqs: sd0-rdqs {
+ samsung,pins = "gpk0-7";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_bus1: sd0-bus-width1 {
+ samsung,pins = "gpk0-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_bus4: sd0-bus-width4 {
+ samsung,pins = "gpk0-4", "gpk0-5", "gpk0-6";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_bus8: sd0-bus-width8 {
+ samsung,pins = "gpl0-0", "gpl0-1", "gpl0-2", "gpl0-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd1_clk: sd1-clk {
+ samsung,pins = "gpk1-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd1_cmd: sd1-cmd {
+ samsung,pins = "gpk1-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd1_cd: sd1-cd {
+ samsung,pins = "gpk1-2";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd1_bus1: sd1-bus-width1 {
+ samsung,pins = "gpk1-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd1_bus4: sd1-bus-width4 {
+ samsung,pins = "gpk1-4", "gpk1-5", "gpk1-6";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd2_clk: sd2-clk {
+ samsung,pins = "gpk2-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <4>;
+ };
+
+ sd2_cmd: sd2-cmd {
+ samsung,pins = "gpk2-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <4>;
+ };
+
+ sd2_cd: sd2-cd {
+ samsung,pins = "gpk2-2";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd2_bus1: sd2-bus-width1 {
+ samsung,pins = "gpk2-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <4>;
+ };
+
+ sd2_bus4: sd2-bus-width4 {
+ samsung,pins = "gpk2-4", "gpk2-5", "gpk2-6";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <4>;
+ };
+
+ cam_port_b_io: cam-port-b-io {
+ samsung,pins = "gpm0-0", "gpm0-1", "gpm0-2", "gpm0-3",
+ "gpm0-4", "gpm0-5", "gpm0-6", "gpm0-7",
+ "gpm1-0", "gpm1-1", "gpm2-0", "gpm2-1";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ cam_port_b_clk_active: cam-port-b-clk-active {
+ samsung,pins = "gpm2-2";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <3>;
+ };
+
+ cam_port_b_clk_idle: cam-port-b-clk-idle {
+ samsung,pins = "gpm2-2";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ fimc_is_i2c0: fimc-is-i2c0 {
+ samsung,pins = "gpm4-0", "gpm4-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ fimc_is_i2c1: fimc-is-i2c1 {
+ samsung,pins = "gpm4-2", "gpm4-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ fimc_is_uart: fimc-is-uart {
+ samsung,pins = "gpm3-5", "gpm3-7";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&pinctrl_2 {
+ gpz: gpz {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ i2s0_bus: i2s0-bus {
+ samsung,pins = "gpz-0", "gpz-1", "gpz-2", "gpz-3",
+ "gpz-4", "gpz-5", "gpz-6";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ etc: etc {
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
diff --git a/arch/arm/boot/dts/exynos4415.dtsi b/arch/arm/boot/dts/exynos4415.dtsi
new file mode 100644
index 0000000..e3c81c1
--- /dev/null
+++ b/arch/arm/boot/dts/exynos4415.dtsi
@@ -0,0 +1,627 @@
+/*
+ * Samsung's Exynos4415 SoC device tree source
+ *
+ * Copyright (c) 2014 Samsung Electronics Co., Ltd.
+ *
+ * Samsung's Exynos4415 SoC device nodes are listed in this file. Exynos4415
+ * based board files can include this file and provide values for board specfic
+ * bindings.
+ *
+ * Note: This file does not include device nodes for all the controllers in
+ * Exynos4415 SoC. As device tree coverage for Exynos4415 increases, additional
+ * nodes can be added to this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "skeleton.dtsi"
+#include <dt-bindings/clock/exynos4415.h>
+#include <dt-bindings/clock/exynos-audss-clk.h>
+
+/ {
+ compatible = "samsung,exynos4415";
+ interrupt-parent = <&gic>;
+
+ aliases {
+ pinctrl0 = &pinctrl_0;
+ pinctrl1 = &pinctrl_1;
+ pinctrl2 = &pinctrl_2;
+ mshc0 = &mshc_0;
+ mshc1 = &mshc_1;
+ mshc2 = &mshc_2;
+ spi0 = &spi_0;
+ spi1 = &spi_1;
+ spi2 = &spi_2;
+ i2c0 = &i2c_0;
+ i2c1 = &i2c_1;
+ i2c2 = &i2c_2;
+ i2c3 = &i2c_3;
+ i2c4 = &i2c_4;
+ i2c5 = &i2c_5;
+ i2c6 = &i2c_6;
+ i2c7 = &i2c_7;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a9";
+ reg = <0xa00>;
+ clock-frequency = <1600000000>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a9";
+ reg = <0xa01>;
+ clock-frequency = <1600000000>;
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a9";
+ reg = <0xa02>;
+ clock-frequency = <1600000000>;
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a9";
+ reg = <0xa03>;
+ clock-frequency = <1600000000>;
+ };
+ };
+
+ soc: soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ fixed-rate-clocks {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ xusbxti: clock@0 {
+ compatible = "fixed-clock";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ clock-frequency = <0>;
+ #clock-cells = <0>;
+ clock-output-names = "xusbxti";
+ };
+
+ xxti: clock@1 {
+ compatible = "fixed-clock";
+ reg = <1>;
+ clock-frequency = <0>;
+ #clock-cells = <0>;
+ clock-output-names = "xxti";
+ };
+ };
+
+ sysram@02020000 {
+ compatible = "mmio-sram";
+ reg = <0x02020000 0x50000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x02020000 0x50000>;
+
+ smp-sysram@0 {
+ compatible = "samsung,exynos4210-sysram";
+ reg = <0x0 0x1000>;
+ };
+
+ smp-sysram@4f000 {
+ compatible = "samsung,exynos4210-sysram-ns";
+ reg = <0x4f000 0x1000>;
+ };
+ };
+
+ pinctrl_2: pinctrl@03860000 {
+ compatible = "samsung,exynos4415-pinctrl";
+ reg = <0x03860000 0x1000>;
+ interrupts = <0 242 0>;
+ };
+
+ chipid@10000000 {
+ compatible = "samsung,exynos4210-chipid";
+ reg = <0x10000000 0x100>;
+ };
+
+ sysreg_system_controller: syscon@10010000 {
+ compatible = "samsung,exynos4-sysreg", "syscon";
+ reg = <0x10010000 0x400>;
+ };
+
+ pmu_system_controller: system-controller@10020000 {
+ compatible = "samsung,exynos4415-pmu", "syscon";
+ reg = <0x10020000 0x4000>;
+ };
+
+ mipi_phy: video-phy@10020710 {
+ compatible = "samsung,s5pv210-mipi-video-phy";
+ reg = <0x10020710 8>;
+ #phy-cells = <1>;
+ };
+
+ pd_cam: cam-power-domain@10024000 {
+ compatible = "samsung,exynos4210-pd";
+ reg = <0x10024000 0x20>;
+ };
+
+ pd_tv: tv-power-domain@10024020 {
+ compatible = "samsung,exynos4210-pd";
+ reg = <0x10024020 0x20>;
+ };
+
+ pd_mfc: mfc-power-domain@10024040 {
+ compatible = "samsung,exynos4210-pd";
+ reg = <0x10024040 0x20>;
+ };
+
+ pd_g3d: g3d-power-domain@10024060 {
+ compatible = "samsung,exynos4210-pd";
+ reg = <0x10024060 0x20>;
+ };
+
+ pd_lcd0: lcd0-power-domain@10024080 {
+ compatible = "samsung,exynos4210-pd";
+ reg = <0x10024080 0x20>;
+ };
+
+ pd_isp0: isp0-power-domain@100240A0 {
+ compatible = "samsung,exynos4210-pd";
+ reg = <0x100240A0 0x20>;
+ };
+
+ pd_isp1: isp1-power-domain@100240E0 {
+ compatible = "samsung,exynos4210-pd";
+ reg = <0x100240E0 0x20>;
+ };
+
+ cmu: clock-controller@10030000 {
+ compatible = "samsung,exynos4415-cmu";
+ reg = <0x10030000 0x18000>;
+ #clock-cells = <1>;
+ };
+
+ rtc: rtc@10070000 {
+ compatible = "samsung,exynos3250-rtc";
+ reg = <0x10070000 0x100>;
+ interrupts = <0 73 0>, <0 74 0>;
+ status = "disabled";
+ };
+
+ mct@10050000 {
+ compatible = "samsung,exynos4210-mct";
+ reg = <0x10050000 0x800>;
+ interrupts = <0 218 0>, <0 219 0>, <0 220 0>, <0 221 0>,
+ <0 223 0>, <0 226 0>, <0 227 0>, <0 228 0>;
+ clocks = <&cmu CLK_FIN_PLL>, <&cmu CLK_MCT>;
+ clock-names = "fin_pll", "mct";
+ };
+
+ gic: interrupt-controller@10481000 {
+ compatible = "arm,cortex-a9-gic";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0x10481000 0x1000>,
+ <0x10482000 0x1000>,
+ <0x10484000 0x2000>,
+ <0x10486000 0x2000>;
+ interrupts = <1 9 0xf04>;
+ };
+
+ l2c: l2-cache-controller@10502000 {
+ compatible = "arm,pl310-cache";
+ reg = <0x10502000 0x1000>;
+ cache-unified;
+ cache-level = <2>;
+ arm,tag-latency = <2 2 1>;
+ arm,data-latency = <3 2 1>;
+ arm,double-linefill = <1>;
+ arm,double-linefill-incr = <0>;
+ arm,double-linefill-wrap = <1>;
+ arm,prefetch-drop = <1>;
+ arm,prefetch-offset = <7>;
+ };
+
+ cmu_dmc: clock-controller@105C0000 {
+ compatible = "samsung,exynos4415-cmu-dmc";
+ reg = <0x105C0000 0x3000>;
+ #clock-cells = <1>;
+ };
+
+ pinctrl_1: pinctrl@11000000 {
+ compatible = "samsung,exynos4415-pinctrl";
+ reg = <0x11000000 0x1000>;
+ interrupts = <0 225 0>;
+
+ wakeup-interrupt-controller {
+ compatible = "samsung,exynos4210-wakeup-eint";
+ interrupt-parent = <&gic>;
+ interrupts = <0 48 0>;
+ };
+ };
+
+ pinctrl_0: pinctrl@11400000 {
+ compatible = "samsung,exynos4415-pinctrl";
+ reg = <0x11400000 0x1000>;
+ interrupts = <0 240 0>;
+ };
+
+ hsotg: hsotg@12480000 {
+ compatible = "samsung,s3c6400-hsotg";
+ reg = <0x12480000 0x20000>;
+ interrupts = <0 141 0>;
+ clocks = <&cmu CLK_USBDEVICE>;
+ clock-names = "otg";
+ phys = <&exynos_usbphy 0>;
+ phy-names = "usb2-phy";
+ status = "disabled";
+ };
+
+ mshc_0: mshc@12510000 {
+ compatible = "samsung,exynos5250-dw-mshc";
+ reg = <0x12510000 0x1000>;
+ interrupts = <0 142 0>;
+ clocks = <&cmu CLK_SDMMC0>, <&cmu CLK_SCLK_MMC0>;
+ clock-names = "biu", "ciu";
+ fifo-depth = <0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ mshc_1: mshc@12520000 {
+ compatible = "samsung,exynos5250-dw-mshc";
+ reg = <0x12520000 0x1000>;
+ interrupts = <0 143 0>;
+ clocks = <&cmu CLK_SDMMC1>, <&cmu CLK_SCLK_MMC1>;
+ clock-names = "biu", "ciu";
+ fifo-depth = <0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ mshc_2: mshc@12530000 {
+ compatible = "samsung,exynos5250-dw-mshc";
+ reg = <0x12530000 0x1000>;
+ interrupts = <0 144 0>;
+ clocks = <&cmu CLK_SDMMC2>, <&cmu CLK_SCLK_MMC2>;
+ clock-names = "biu", "ciu";
+ fifo-depth = <0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ ehci: ehci@12580000 {
+ compatible = "samsung,exynos4210-ehci";
+ reg = <0x12580000 0x100>;
+ interrupts = <0 140 0>;
+ clocks = <&cmu CLK_USBHOST>;
+ clock-names = "usbhost";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ phys = <&exynos_usbphy 1>;
+ status = "disabled";
+ };
+ port@1 {
+ reg = <1>;
+ phys = <&exynos_usbphy 2>;
+ status = "disabled";
+ };
+ port@2 {
+ reg = <2>;
+ phys = <&exynos_usbphy 3>;
+ status = "disabled";
+ };
+ };
+
+ ohci: ohci@12590000 {
+ compatible = "samsung,exynos4210-ohci";
+ reg = <0x12590000 0x100>;
+ interrupts = <0 140 0>;
+ clocks = <&cmu CLK_USBHOST>;
+ clock-names = "usbhost";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ phys = <&exynos_usbphy 1>;
+ status = "disabled";
+ };
+ };
+
+ exynos_usbphy: exynos-usbphy@125B0000 {
+ compatible = "samsung,exynos4x12-usb2-phy";
+ reg = <0x125B0000 0x100>;
+ samsung,pmureg-phandle = <&pmu_system_controller>;
+ samsung,sysreg-phandle = <&sysreg_system_controller>;
+ clocks = <&cmu CLK_USBDEVICE>, <&xusbxti>;
+ clock-names = "phy", "ref";
+ #phy-cells = <1>;
+ status = "disabled";
+ };
+
+ amba {
+ compatible = "arm,amba-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-parent = <&gic>;
+ ranges;
+
+ pdma0: pdma@12680000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x12680000 0x1000>;
+ interrupts = <0 138 0>;
+ clocks = <&cmu CLK_PDMA0>;
+ clock-names = "apb_pclk";
+ #dma-cells = <1>;
+ #dma-channels = <8>;
+ #dma-requests = <32>;
+ };
+
+ pdma1: pdma@12690000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x12690000 0x1000>;
+ interrupts = <0 139 0>;
+ clocks = <&cmu CLK_PDMA1>;
+ clock-names = "apb_pclk";
+ #dma-cells = <1>;
+ #dma-channels = <8>;
+ #dma-requests = <32>;
+ };
+ };
+
+ adc: adc@126C0000 {
+ compatible = "samsung,exynos3250-adc",
+ "samsung,exynos-adc-v2";
+ reg = <0x126C0000 0x100>, <0x10020718 0x4>;
+ interrupts = <0 137 0>;
+ clock-names = "adc", "sclk";
+ clocks = <&cmu CLK_TSADC>, <&cmu CLK_SCLK_TSADC>;
+ #io-channel-cells = <1>;
+ io-channel-ranges;
+ status = "disabled";
+ };
+
+ serial_0: serial@13800000 {
+ compatible = "samsung,exynos4210-uart";
+ reg = <0x13800000 0x100>;
+ interrupts = <0 109 0>;
+ clocks = <&cmu CLK_UART0>, <&cmu CLK_SCLK_UART0>;
+ clock-names = "uart", "clk_uart_baud0";
+ status = "disabled";
+ };
+
+ serial_1: serial@13810000 {
+ compatible = "samsung,exynos4210-uart";
+ reg = <0x13810000 0x100>;
+ interrupts = <0 110 0>;
+ clocks = <&cmu CLK_UART1>, <&cmu CLK_SCLK_UART1>;
+ clock-names = "uart", "clk_uart_baud0";
+ status = "disabled";
+ };
+
+ serial_2: serial@13820000 {
+ compatible = "samsung,exynos4210-uart";
+ reg = <0x13820000 0x100>;
+ interrupts = <0 111 0>;
+ clocks = <&cmu CLK_UART2>, <&cmu CLK_SCLK_UART2>;
+ clock-names = "uart", "clk_uart_baud0";
+ status = "disabled";
+ };
+
+ serial_3: serial@13830000 {
+ compatible = "samsung,exynos4210-uart";
+ reg = <0x13830000 0x100>;
+ interrupts = <0 112 0>;
+ clocks = <&cmu CLK_UART3>, <&cmu CLK_SCLK_UART3>;
+ clock-names = "uart", "clk_uart_baud0";
+ status = "disabled";
+ };
+
+ i2c_0: i2c@13860000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x13860000 0x100>;
+ interrupts = <0 113 0>;
+ clocks = <&cmu CLK_I2C0>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_bus>;
+ status = "disabled";
+ };
+
+ i2c_1: i2c@13870000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x13870000 0x100>;
+ interrupts = <0 114 0>;
+ clocks = <&cmu CLK_I2C1>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_bus>;
+ status = "disabled";
+ };
+
+ i2c_2: i2c@13880000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x13880000 0x100>;
+ interrupts = <0 115 0>;
+ clocks = <&cmu CLK_I2C2>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_bus>;
+ status = "disabled";
+ };
+
+ i2c_3: i2c@13890000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x13890000 0x100>;
+ interrupts = <0 116 0>;
+ clocks = <&cmu CLK_I2C3>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_bus>;
+ status = "disabled";
+ };
+
+ i2c_4: i2c@138A0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x138A0000 0x100>;
+ interrupts = <0 117 0>;
+ clocks = <&cmu CLK_I2C4>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_bus>;
+ status = "disabled";
+ };
+
+ i2c_5: i2c@138B0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x138B0000 0x100>;
+ interrupts = <0 118 0>;
+ clocks = <&cmu CLK_I2C5>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c5_bus>;
+ status = "disabled";
+ };
+
+ i2c_6: i2c@138C0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x138C0000 0x100>;
+ interrupts = <0 119 0>;
+ clocks = <&cmu CLK_I2C6>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c6_bus>;
+ status = "disabled";
+ };
+
+ i2c_7: i2c@138D0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x138D0000 0x100>;
+ interrupts = <0 120 0>;
+ clocks = <&cmu CLK_I2C7>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c7_bus>;
+ status = "disabled";
+ };
+
+ spi_0: spi@13920000 {
+ compatible = "samsung,exynos4210-spi";
+ reg = <0x13920000 0x100>;
+ interrupts = <0 121 0>;
+ dmas = <&pdma0 7>, <&pdma0 6>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&cmu CLK_SPI0>, <&cmu CLK_SCLK_SPI0>;
+ clock-names = "spi", "spi_busclk0";
+ samsung,spi-src-clk = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_bus>;
+ status = "disabled";
+ };
+
+ spi_1: spi@13930000 {
+ compatible = "samsung,exynos4210-spi";
+ reg = <0x13930000 0x100>;
+ interrupts = <0 122 0>;
+ dmas = <&pdma1 7>, <&pdma1 6>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&cmu CLK_SPI1>, <&cmu CLK_SCLK_SPI1>;
+ clock-names = "spi", "spi_busclk0";
+ samsung,spi-src-clk = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_bus>;
+ status = "disabled";
+ };
+
+ spi_2: spi@13940000 {
+ compatible = "samsung,exynos4210-spi";
+ reg = <0x13940000 0x100>;
+ interrupts = <0 123 0>;
+ dmas = <&pdma0 9>, <&pdma0 8>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&cmu CLK_SPI2>, <&cmu CLK_SCLK_SPI2>;
+ clock-names = "spi", "spi_busclk0";
+ samsung,spi-src-clk = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_bus>;
+ status = "disabled";
+ };
+
+ clock_audss: clock-controller@03810000 {
+ compatible = "samsung,exynos4210-audss-clock";
+ reg = <0x03810000 0x0C>;
+ #clock-cells = <1>;
+ };
+
+ i2s0: i2s@3830000 {
+ compatible = "samsung,s5pv210-i2s";
+ reg = <0x03830000 0x100>;
+ interrupts = <0 124 0>;
+ clocks = <&clock_audss EXYNOS_I2S_BUS>,
+ <&clock_audss EXYNOS_SCLK_I2S>;
+ clock-names = "iis", "i2s_opclk0";
+ dmas = <&pdma1 10>, <&pdma1 9>, <&pdma1 8>;
+ dma-names = "tx", "rx", "tx-sec";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s0_bus>;
+ samsung,idma-addr = <0x03000000>;
+ status = "disabled";
+ };
+
+ pwm: pwm@139D0000 {
+ compatible = "samsung,exynos4210-pwm";
+ reg = <0x139D0000 0x1000>;
+ interrupts = <0 104 0>, <0 105 0>, <0 106 0>,
+ <0 107 0>, <0 108 0>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ pmu {
+ compatible = "arm,cortex-a9-pmu";
+ interrupts = <0 18 0>, <0 19 0>, <0 20 0>, <0 21 0>;
+ };
+ };
+};
+
+#include "exynos4415-pinctrl.dtsi"
--
1.8.0
^ permalink raw reply related [flat|nested] 21+ messages in thread
* Re: [PATCH 3/5] clk: samsung: Document binding for Exynos4415 clock controller
2014-10-20 3:32 ` [PATCH 3/5] clk: samsung: Document binding for Exynos4415 clock controller Chanwoo Choi
@ 2014-10-24 10:32 ` Sylwester Nawrocki
2014-10-24 10:34 ` Chanwoo Choi
0 siblings, 1 reply; 21+ messages in thread
From: Sylwester Nawrocki @ 2014-10-24 10:32 UTC (permalink / raw)
To: Chanwoo Choi
Cc: linux-samsung-soc, linux-kernel, linux-arm-kernel, kgene.kim,
ben-linux, linux, mark.rutland, arnd, olof, tomasz.figa,
mturquette, thomas.abraham, linus.walleij, sw0312.kim,
kyungmin.park, inki.dae, geunsik.lim, jh80.chung, jaewon02.kim,
ideal.song, yj44.cho
On 20/10/14 05:32, Chanwoo Choi wrote:
> The Exynos4415 clocks are statically listed and registered using the
> Samsung specific common clock helper functions. Both device tree based
> clock lookup and clkdev based clock lookups are supported.
I think the above text is not relevant, DT binding is not supposed
to depend on any OS. Instead I would just put here something like:
"This patch adds DT binding documentation for Exynos4415 SoC system
clock controllers."
> Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
> Cc: Tomasz Figa <tomasz.figa@gmail.com>
> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
> Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
> ---
> .../devicetree/bindings/clock/exynos4415-clock.txt | 49 ++++++++++++++++++++++
> 1 file changed, 49 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/clock/exynos4415-clock.txt
>
> diff --git a/Documentation/devicetree/bindings/clock/exynos4415-clock.txt b/Documentation/devicetree/bindings/clock/exynos4415-clock.txt
> new file mode 100644
> index 0000000..8aa4f4f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/clock/exynos4415-clock.txt
> @@ -0,0 +1,49 @@
> +* Samsung Exynos4415 Clock Controller
> +
> +The Exynos4415 clock controller generates and supplies clock to various
> +controllers within the Exynos4415 SoC.
s/controllers/consumer devices/ ?
> +
> +Required Properties:
s/P/p/ ?
> +
> +- compatible: should be one of the following.
s/./:/ ?
> + - "samsung,exynos4415-cmu" - controller compatible with Exynos4415 SoC.
>From current description it seems "samsung,exynos4415-cmu-dmc" is compatible
with "samsung,exynos4415-cmu", which is not the case AFAIK.
Perhaps we should change description here to something along the lines of:
- "samsung,exynos4415-cmu" - for the main system clocks controller
(CMU_LEFTBUS, CMU_RIGHTBUS, CMU_TOP, CMU_CPU clock domains),
> + - "samsung,exynos4415-cmu-dmc" - controller compatible with
> + Exynos4415 SoC for Dynamic Memory Controller domain.
This seems unclear, how about
- "samsung,exynos4415-cmu-dmc" - for the Exynos4415 SoC DRAM Memory
Controller (DMC) domain clock controller.
?
> +- reg: physical base address of the controller and length of memory mapped
> + region.
> +
> +- #clock-cells: should be 1.
> +
> +Each clock is assigned an identifier and client nodes can use this identifier
> +to specify the clock which they consume.
> +
> +All available clocks are defined as preprocessor macros in
> +dt-bindings/clock/exynos4415.h header and can be used in device
> +tree sources.
> +Example 1: An example of a clock controller node is listed below.
> +
> + cmu: clock-controller@10030000 {
> + compatible = "samsung,exynos4415-cmu";
> + reg = <0x10030000 0x18000>;
> + #clock-cells = <1>;
> + };
> +
> + cmu-dmc: clock-controller@105C0000 {
> + compatible = "samsung,exynos4415-cmu-dmc";
> + reg = <0x105C0000 0x3000>;
> + #clock-cells = <1>;
> + };
> +
> +Example 2: UART controller node that consumes the clock generated by the clock
> + controller. Refer to the standard clock bindings for information
> + about 'clocks' and 'clock-names' property.
> +
> + serial_0: serial@13800000 {
> + compatible = "samsung,exynos4210-uart";
> + reg = <0x13800000 0x100>;
> + interrupts = <0 109 0>;
> + clocks = <&cmu CLK_UART0>, <&cmu CLK_SCLK_UART0>;
> + clock-names = "uart", "clk_uart_baud0";
> + };
I think we could omit those example snippets, it's all generic stuff and
there is already plenty examples in descriptions of the DT binding for
other SoCs.
--
Regards,
Sylwester
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 3/5] clk: samsung: Document binding for Exynos4415 clock controller
2014-10-24 10:32 ` Sylwester Nawrocki
@ 2014-10-24 10:34 ` Chanwoo Choi
0 siblings, 0 replies; 21+ messages in thread
From: Chanwoo Choi @ 2014-10-24 10:34 UTC (permalink / raw)
To: Sylwester Nawrocki
Cc: linux-samsung-soc, linux-kernel, linux-arm-kernel, kgene.kim,
ben-linux, linux, mark.rutland, arnd, olof, tomasz.figa,
mturquette, thomas.abraham, linus.walleij, sw0312.kim,
kyungmin.park, inki.dae, geunsik.lim, jh80.chung, jaewon02.kim,
ideal.song, yj44.cho
Hi Sylwester,
On 10/24/2014 07:32 PM, Sylwester Nawrocki wrote:
> On 20/10/14 05:32, Chanwoo Choi wrote:
>> The Exynos4415 clocks are statically listed and registered using the
>> Samsung specific common clock helper functions. Both device tree based
>> clock lookup and clkdev based clock lookups are supported.
>
> I think the above text is not relevant, DT binding is not supposed
> to depend on any OS. Instead I would just put here something like:
>
> "This patch adds DT binding documentation for Exynos4415 SoC system
> clock controllers."
OK, I will modify it as your comment.
>
>> Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
>> Cc: Tomasz Figa <tomasz.figa@gmail.com>
>> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
>> Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
>> ---
>> .../devicetree/bindings/clock/exynos4415-clock.txt | 49 ++++++++++++++++++++++
>> 1 file changed, 49 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/clock/exynos4415-clock.txt
>>
>> diff --git a/Documentation/devicetree/bindings/clock/exynos4415-clock.txt b/Documentation/devicetree/bindings/clock/exynos4415-clock.txt
>> new file mode 100644
>> index 0000000..8aa4f4f
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/clock/exynos4415-clock.txt
>> @@ -0,0 +1,49 @@
>> +* Samsung Exynos4415 Clock Controller
>> +
>> +The Exynos4415 clock controller generates and supplies clock to various
>> +controllers within the Exynos4415 SoC.
>
> s/controllers/consumer devices/ ?
>
>> +
>> +Required Properties:
>
> s/P/p/ ?
I'll fix it.
>
>> +
>> +- compatible: should be one of the following.
>
> s/./:/ ?
I will change it (. -> :)
>
>> + - "samsung,exynos4415-cmu" - controller compatible with Exynos4415 SoC.
>
>>From current description it seems "samsung,exynos4415-cmu-dmc" is compatible
> with "samsung,exynos4415-cmu", which is not the case AFAIK.
> Perhaps we should change description here to something along the lines of:
>
> - "samsung,exynos4415-cmu" - for the main system clocks controller
> (CMU_LEFTBUS, CMU_RIGHTBUS, CMU_TOP, CMU_CPU clock domains),
>
>> + - "samsung,exynos4415-cmu-dmc" - controller compatible with
>> + Exynos4415 SoC for Dynamic Memory Controller domain.
>
> This seems unclear, how about
>
> - "samsung,exynos4415-cmu-dmc" - for the Exynos4415 SoC DRAM Memory
> Controller (DMC) domain clock controller.
>
> ?
OK, I'll modify it
>> +- reg: physical base address of the controller and length of memory mapped
>> + region.
>> +
>> +- #clock-cells: should be 1.
>> +
>> +Each clock is assigned an identifier and client nodes can use this identifier
>> +to specify the clock which they consume.
>> +
>> +All available clocks are defined as preprocessor macros in
>> +dt-bindings/clock/exynos4415.h header and can be used in device
>> +tree sources.
>
>> +Example 1: An example of a clock controller node is listed below.
>> +
>> + cmu: clock-controller@10030000 {
>> + compatible = "samsung,exynos4415-cmu";
>> + reg = <0x10030000 0x18000>;
>> + #clock-cells = <1>;
>> + };
>> +
>> + cmu-dmc: clock-controller@105C0000 {
>> + compatible = "samsung,exynos4415-cmu-dmc";
>> + reg = <0x105C0000 0x3000>;
>> + #clock-cells = <1>;
>> + };
>> +
>> +Example 2: UART controller node that consumes the clock generated by the clock
>> + controller. Refer to the standard clock bindings for information
>> + about 'clocks' and 'clock-names' property.
>> +
>> + serial_0: serial@13800000 {
>> + compatible = "samsung,exynos4210-uart";
>> + reg = <0x13800000 0x100>;
>> + interrupts = <0 109 0>;
>> + clocks = <&cmu CLK_UART0>, <&cmu CLK_SCLK_UART0>;
>> + clock-names = "uart", "clk_uart_baud0";
>> + };
>
> I think we could omit those example snippets, it's all generic stuff and
> there is already plenty examples in descriptions of the DT binding for
> other SoCs.
OK, I'll drop this example.
Thanks for your review.
Best Regards,
Chanwoo Choi
>
> --
> Regards,
> Sylwester
>
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 2/5] clk: samsung: exynos4415: Add clocks using common clock framework
2014-10-20 3:32 ` [PATCH 2/5] clk: samsung: exynos4415: Add clocks using common clock framework Chanwoo Choi
@ 2014-10-24 10:54 ` Sylwester Nawrocki
2014-10-24 10:59 ` Chanwoo Choi
2014-10-24 13:18 ` Daniel Drake
1 sibling, 1 reply; 21+ messages in thread
From: Sylwester Nawrocki @ 2014-10-24 10:54 UTC (permalink / raw)
To: Chanwoo Choi
Cc: linux-samsung-soc, linux-kernel, linux-arm-kernel, kgene.kim,
ben-linux, linux, mark.rutland, arnd, olof, tomasz.figa,
mturquette, thomas.abraham, linus.walleij, sw0312.kim,
kyungmin.park, inki.dae, geunsik.lim, jh80.chung, jaewon02.kim,
ideal.song, yj44.cho
On 20/10/14 05:32, Chanwoo Choi wrote:
> This patch adds the new clock driver of Exynos4415 SoC based on Cortex-A9
> using common clock framework. The CMU (Clock Management Unit) of Exynos4415
> controls PLLs(Phase Locked Loops) and generates system clocks for CPU, buses
> and function clocks for individual IPs.
>
> Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
> Cc: Tomasz Figa <tomasz.figa@gmail.com>
> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
> Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
> Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
> Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
The patch looks good to me, I've applied it to my tree and will
be sending in a pull request to Mike next week, if there is no
objections.
--
Thanks,
Sylwester
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 2/5] clk: samsung: exynos4415: Add clocks using common clock framework
2014-10-24 10:54 ` Sylwester Nawrocki
@ 2014-10-24 10:59 ` Chanwoo Choi
0 siblings, 0 replies; 21+ messages in thread
From: Chanwoo Choi @ 2014-10-24 10:59 UTC (permalink / raw)
To: Sylwester Nawrocki
Cc: linux-samsung-soc, linux-kernel, linux-arm-kernel, kgene.kim,
ben-linux, linux, mark.rutland, arnd, olof, tomasz.figa,
mturquette, thomas.abraham, linus.walleij, sw0312.kim,
kyungmin.park, inki.dae, geunsik.lim, jh80.chung, jaewon02.kim,
ideal.song, yj44.cho
On 10/24/2014 07:54 PM, Sylwester Nawrocki wrote:
> On 20/10/14 05:32, Chanwoo Choi wrote:
>> This patch adds the new clock driver of Exynos4415 SoC based on Cortex-A9
>> using common clock framework. The CMU (Clock Management Unit) of Exynos4415
>> controls PLLs(Phase Locked Loops) and generates system clocks for CPU, buses
>> and function clocks for individual IPs.
>>
>> Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
>> Cc: Tomasz Figa <tomasz.figa@gmail.com>
>> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
>> Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
>> Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
>> Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
>
> The patch looks good to me, I've applied it to my tree and will
> be sending in a pull request to Mike next week, if there is no
> objections.
Thanks,
I'll send new patchset(v2) for following Exynos4412 patches right now.
clk: samsung: exynos4415: Add clocks using common clock framework
clk: samsung: Document binding for Exynos4415 clock controller
Best Regards,
Chanwoo Choi
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 1/5] ARM: EXYNOS: Add EXYNOS4415 SoC ID
2014-10-20 3:32 ` [PATCH 1/5] ARM: EXYNOS: Add EXYNOS4415 SoC ID Chanwoo Choi
@ 2014-10-24 11:43 ` Tomasz Figa
2014-10-24 11:46 ` Chanwoo Choi
0 siblings, 1 reply; 21+ messages in thread
From: Tomasz Figa @ 2014-10-24 11:43 UTC (permalink / raw)
To: Chanwoo Choi, linux-samsung-soc, linux-kernel, linux-arm-kernel
Cc: kgene.kim, ben-linux, linux, mark.rutland, arnd, olof,
mturquette, thomas.abraham, linus.walleij, sw0312.kim,
kyungmin.park, inki.dae, geunsik.lim, jh80.chung, jaewon02.kim,
ideal.song, yj44.cho
Hi Chanwoo,
On 20.10.2014 05:32, Chanwoo Choi wrote:
> This patch add Exynos4415's SoC ID. Exynos4415 is based on the 32-bit RISC
> processor for Smartphone. Exynos4415 uses Cortex A9 quad-cores and has a target
> speed of 1.6GHz and provides 8.5GB/s memory bandwidth.
>
> Cc: Kukjin Kim <kgene.kim@samsung.com>
> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
> Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
> ---
> arch/arm/mach-exynos/Kconfig | 5 +++++
> arch/arm/mach-exynos/common.h | 8 ++++++++
> arch/arm/mach-exynos/exynos.c | 2 ++
> 3 files changed, 15 insertions(+)
>
> diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig
> index 46f3c0d..349c867 100644
> --- a/arch/arm/mach-exynos/Kconfig
> +++ b/arch/arm/mach-exynos/Kconfig
> @@ -75,6 +75,11 @@ config SOC_EXYNOS4412
> default y
> depends on ARCH_EXYNOS4
>
> +config SOC_EXYNOS4415
> + bool "SAMSUNG EXYNOS4415"
> + default y
> + depends on ARCH_EXYNOS4
> +
> config SOC_EXYNOS5250
> bool "SAMSUNG EXYNOS5250"
> default y
> diff --git a/arch/arm/mach-exynos/common.h b/arch/arm/mach-exynos/common.h
> index d4d09bc..ffc0c22 100644
> --- a/arch/arm/mach-exynos/common.h
> +++ b/arch/arm/mach-exynos/common.h
> @@ -21,6 +21,7 @@
> #define EXYNOS4210_CPU_ID 0x43210000
> #define EXYNOS4212_CPU_ID 0x43220000
> #define EXYNOS4412_CPU_ID 0xE4412200
> +#define EXYNOS4415_CPU_ID 0xE4415000
> #define EXYNOS4_CPU_MASK 0xFFFE0000
>
> #define EXYNOS5250_SOC_ID 0x43520000
> @@ -42,6 +43,7 @@ IS_SAMSUNG_CPU(exynos3250, EXYNOS3250_SOC_ID, EXYNOS3_SOC_MASK)
> IS_SAMSUNG_CPU(exynos4210, EXYNOS4210_CPU_ID, EXYNOS4_CPU_MASK)
> IS_SAMSUNG_CPU(exynos4212, EXYNOS4212_CPU_ID, EXYNOS4_CPU_MASK)
> IS_SAMSUNG_CPU(exynos4412, EXYNOS4412_CPU_ID, EXYNOS4_CPU_MASK)
> +IS_SAMSUNG_CPU(exynos4415, EXYNOS4415_CPU_ID, EXYNOS4_CPU_MASK)
Is there a need for this legacy helper for this SoC?
> IS_SAMSUNG_CPU(exynos5250, EXYNOS5250_SOC_ID, EXYNOS5_SOC_MASK)
> IS_SAMSUNG_CPU(exynos5410, EXYNOS5410_SOC_ID, EXYNOS5_SOC_MASK)
> IS_SAMSUNG_CPU(exynos5420, EXYNOS5420_SOC_ID, EXYNOS5_SOC_MASK)
> @@ -72,6 +74,12 @@ IS_SAMSUNG_CPU(exynos5800, EXYNOS5800_SOC_ID, EXYNOS5_SOC_MASK)
> # define soc_is_exynos4412() 0
> #endif
>
> +#if defined(CONFIG_SOC_EXYNOS4415)
> +# define soc_is_exynos4415() is_samsung_exynos4415()
> +#else
> +# define soc_is_exynos4415() 0
> +#endif
Ditto.
Best regards,
Tomasz
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 1/5] ARM: EXYNOS: Add EXYNOS4415 SoC ID
2014-10-24 11:43 ` Tomasz Figa
@ 2014-10-24 11:46 ` Chanwoo Choi
0 siblings, 0 replies; 21+ messages in thread
From: Chanwoo Choi @ 2014-10-24 11:46 UTC (permalink / raw)
To: Tomasz Figa
Cc: linux-samsung-soc, linux-kernel, linux-arm-kernel, kgene.kim,
ben-linux, linux, mark.rutland, arnd, olof, mturquette,
thomas.abraham, linus.walleij, sw0312.kim, kyungmin.park,
inki.dae, geunsik.lim, jh80.chung, jaewon02.kim, ideal.song,
yj44.cho
Hi Tomasz,
On 10/24/2014 08:43 PM, Tomasz Figa wrote:
> Hi Chanwoo,
>
> On 20.10.2014 05:32, Chanwoo Choi wrote:
>> This patch add Exynos4415's SoC ID. Exynos4415 is based on the 32-bit RISC
>> processor for Smartphone. Exynos4415 uses Cortex A9 quad-cores and has a target
>> speed of 1.6GHz and provides 8.5GB/s memory bandwidth.
>>
>> Cc: Kukjin Kim <kgene.kim@samsung.com>
>> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
>> Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
>> ---
>> arch/arm/mach-exynos/Kconfig | 5 +++++
>> arch/arm/mach-exynos/common.h | 8 ++++++++
>> arch/arm/mach-exynos/exynos.c | 2 ++
>> 3 files changed, 15 insertions(+)
>>
>> diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig
>> index 46f3c0d..349c867 100644
>> --- a/arch/arm/mach-exynos/Kconfig
>> +++ b/arch/arm/mach-exynos/Kconfig
>> @@ -75,6 +75,11 @@ config SOC_EXYNOS4412
>> default y
>> depends on ARCH_EXYNOS4
>>
>> +config SOC_EXYNOS4415
>> + bool "SAMSUNG EXYNOS4415"
>> + default y
>> + depends on ARCH_EXYNOS4
>> +
>> config SOC_EXYNOS5250
>> bool "SAMSUNG EXYNOS5250"
>> default y
>> diff --git a/arch/arm/mach-exynos/common.h b/arch/arm/mach-exynos/common.h
>> index d4d09bc..ffc0c22 100644
>> --- a/arch/arm/mach-exynos/common.h
>> +++ b/arch/arm/mach-exynos/common.h
>> @@ -21,6 +21,7 @@
>> #define EXYNOS4210_CPU_ID 0x43210000
>> #define EXYNOS4212_CPU_ID 0x43220000
>> #define EXYNOS4412_CPU_ID 0xE4412200
>> +#define EXYNOS4415_CPU_ID 0xE4415000
>> #define EXYNOS4_CPU_MASK 0xFFFE0000
>>
>> #define EXYNOS5250_SOC_ID 0x43520000
>> @@ -42,6 +43,7 @@ IS_SAMSUNG_CPU(exynos3250, EXYNOS3250_SOC_ID, EXYNOS3_SOC_MASK)
>> IS_SAMSUNG_CPU(exynos4210, EXYNOS4210_CPU_ID, EXYNOS4_CPU_MASK)
>> IS_SAMSUNG_CPU(exynos4212, EXYNOS4212_CPU_ID, EXYNOS4_CPU_MASK)
>> IS_SAMSUNG_CPU(exynos4412, EXYNOS4412_CPU_ID, EXYNOS4_CPU_MASK)
>> +IS_SAMSUNG_CPU(exynos4415, EXYNOS4415_CPU_ID, EXYNOS4_CPU_MASK)
>
> Is there a need for this legacy helper for this SoC?
No, I'll drop it on next patchset.
>
>> IS_SAMSUNG_CPU(exynos5250, EXYNOS5250_SOC_ID, EXYNOS5_SOC_MASK)
>> IS_SAMSUNG_CPU(exynos5410, EXYNOS5410_SOC_ID, EXYNOS5_SOC_MASK)
>> IS_SAMSUNG_CPU(exynos5420, EXYNOS5420_SOC_ID, EXYNOS5_SOC_MASK)
>> @@ -72,6 +74,12 @@ IS_SAMSUNG_CPU(exynos5800, EXYNOS5800_SOC_ID, EXYNOS5_SOC_MASK)
>> # define soc_is_exynos4412() 0
>> #endif
>>
>> +#if defined(CONFIG_SOC_EXYNOS4415)
>> +# define soc_is_exynos4415() is_samsung_exynos4415()
>> +#else
>> +# define soc_is_exynos4415() 0
>> +#endif
>
> Ditto.
I'll drop it on next patchset.
Best Regards,
Chanwoo Choi
>
> Best regards,
> Tomasz
> --
> To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 2/5] clk: samsung: exynos4415: Add clocks using common clock framework
2014-10-20 3:32 ` [PATCH 2/5] clk: samsung: exynos4415: Add clocks using common clock framework Chanwoo Choi
2014-10-24 10:54 ` Sylwester Nawrocki
@ 2014-10-24 13:18 ` Daniel Drake
2014-10-24 13:28 ` Tomasz Figa
` (2 more replies)
1 sibling, 3 replies; 21+ messages in thread
From: Daniel Drake @ 2014-10-24 13:18 UTC (permalink / raw)
To: Chanwoo Choi
Cc: linux-samsung-soc, Linux Kernel, linux-arm-kernel, Kukjin Kim,
ben-linux, Russell King, Mark Rutland, Arnd Bergmann,
Olof Johansson, Tomasz Figa, Mike Turquette, thomas.abraham,
Linus Walleij, Seung-Woo Kim, Kyungmin Park, InKi Dae,
geunsik.lim, jh80.chung, jaewon02.kim, ideal.song, yj44.cho,
Sylwester Nawrocki
On Sun, Oct 19, 2014 at 9:32 PM, Chanwoo Choi <cw00.choi@samsung.com> wrote:
> This patch adds the new clock driver of Exynos4415 SoC based on Cortex-A9
> using common clock framework. The CMU (Clock Management Unit) of Exynos4415
> controls PLLs(Phase Locked Loops) and generates system clocks for CPU, buses
> and function clocks for individual IPs.
There seems to be a lot in common here with other exynos4 variants in
clk-exynos4.c. Have you considered just adding support for the 4415 in
the existing driver?
Thanks
Daniel
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 5/5] ARM: dts: Add dts files for Exynos4415 SoC
2014-10-20 3:32 ` [PATCH 5/5] ARM: dts: Add dts files for Exynos4415 SoC Chanwoo Choi
@ 2014-10-24 13:23 ` Daniel Drake
2014-10-24 13:30 ` Tomasz Figa
` (2 more replies)
0 siblings, 3 replies; 21+ messages in thread
From: Daniel Drake @ 2014-10-24 13:23 UTC (permalink / raw)
To: Chanwoo Choi
Cc: linux-samsung-soc, Linux Kernel, linux-arm-kernel, Kukjin Kim,
ben-linux, Russell King, Mark Rutland, Arnd Bergmann,
Olof Johansson, Tomasz Figa, Mike Turquette, thomas.abraham,
Linus Walleij, Seung-Woo Kim, Kyungmin Park, InKi Dae,
geunsik.lim, jh80.chung, jaewon02.kim, ideal.song, yj44.cho,
Marek Szyprowski
On Sun, Oct 19, 2014 at 9:32 PM, Chanwoo Choi <cw00.choi@samsung.com> wrote:
> This patch adds new exynos4415.dtsi to support Exynos4415 SoC
> based on Cortex-A9 quad cores and includes following dt nodes:
There's a lot in common between your new exynos4415.dtsi and the
existing exynos4.dtsi.
Would it make more sense for the 4415 code to extend the existing
exynos4.dtsi like the other Exynos4 variants do?
Thanks
Daniel
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 2/5] clk: samsung: exynos4415: Add clocks using common clock framework
2014-10-24 13:18 ` Daniel Drake
@ 2014-10-24 13:28 ` Tomasz Figa
2014-10-24 13:36 ` Chanwoo Choi
2014-10-24 13:56 ` Sylwester Nawrocki
2 siblings, 0 replies; 21+ messages in thread
From: Tomasz Figa @ 2014-10-24 13:28 UTC (permalink / raw)
To: Daniel Drake, Chanwoo Choi
Cc: linux-samsung-soc, Linux Kernel, linux-arm-kernel, Kukjin Kim,
ben-linux, Russell King, Mark Rutland, Arnd Bergmann,
Olof Johansson, Mike Turquette, thomas.abraham, Linus Walleij,
Seung-Woo Kim, Kyungmin Park, InKi Dae, geunsik.lim, jh80.chung,
jaewon02.kim, ideal.song, yj44.cho, Sylwester Nawrocki
On 24.10.2014 15:18, Daniel Drake wrote:
> On Sun, Oct 19, 2014 at 9:32 PM, Chanwoo Choi <cw00.choi@samsung.com> wrote:
>> This patch adds the new clock driver of Exynos4415 SoC based on Cortex-A9
>> using common clock framework. The CMU (Clock Management Unit) of Exynos4415
>> controls PLLs(Phase Locked Loops) and generates system clocks for CPU, buses
>> and function clocks for individual IPs.
>
> There seems to be a lot in common here with other exynos4 variants in
> clk-exynos4.c. Have you considered just adding support for the 4415 in
> the existing driver?
I tried when I was still at Samsung and the outcome was far from being
nice. There are certain differences, such as separate address spaces of
few clock controllers and different bit fields in apparently similar
registers, which made resulting code quite ugly.
Also another advantage of separate driver is that it can be made without
duplicating initial fails of the driver for Exynos4, such as private
bindings for external clocks or clock controllers in different power
domains grouped together into one big logical clock controller, because
at development time they looked so (contiguous address space).
Best regards,
Tomasz
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 5/5] ARM: dts: Add dts files for Exynos4415 SoC
2014-10-24 13:23 ` Daniel Drake
@ 2014-10-24 13:30 ` Tomasz Figa
2014-10-24 13:34 ` Marek Szyprowski
2014-10-24 13:53 ` Chanwoo Choi
2 siblings, 0 replies; 21+ messages in thread
From: Tomasz Figa @ 2014-10-24 13:30 UTC (permalink / raw)
To: Daniel Drake, Chanwoo Choi
Cc: linux-samsung-soc, Linux Kernel, linux-arm-kernel, Kukjin Kim,
ben-linux, Russell King, Mark Rutland, Arnd Bergmann,
Olof Johansson, Mike Turquette, thomas.abraham, Linus Walleij,
Seung-Woo Kim, Kyungmin Park, InKi Dae, geunsik.lim, jh80.chung,
jaewon02.kim, ideal.song, yj44.cho, Marek Szyprowski
On 24.10.2014 15:23, Daniel Drake wrote:
> On Sun, Oct 19, 2014 at 9:32 PM, Chanwoo Choi <cw00.choi@samsung.com> wrote:
>> This patch adds new exynos4415.dtsi to support Exynos4415 SoC
>> based on Cortex-A9 quad cores and includes following dt nodes:
>
> There's a lot in common between your new exynos4415.dtsi and the
> existing exynos4.dtsi.
> Would it make more sense for the 4415 code to extend the existing
> exynos4.dtsi like the other Exynos4 variants do?
This would make sense, but then existing Exynos 4 device tree sources
would have to be refactored to use reference-based syntax for extending
nodes. (Which is desirable anyway, but adds quite a bit of effort and
could be prone to conflicts.) I'd say that they could be merged later
anyway.
Best regards,
Tomasz
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 5/5] ARM: dts: Add dts files for Exynos4415 SoC
2014-10-24 13:23 ` Daniel Drake
2014-10-24 13:30 ` Tomasz Figa
@ 2014-10-24 13:34 ` Marek Szyprowski
2014-10-24 13:44 ` Daniel Drake
2014-10-24 13:53 ` Chanwoo Choi
2 siblings, 1 reply; 21+ messages in thread
From: Marek Szyprowski @ 2014-10-24 13:34 UTC (permalink / raw)
To: Daniel Drake, Chanwoo Choi
Cc: linux-samsung-soc, Linux Kernel, linux-arm-kernel, Kukjin Kim,
ben-linux, Russell King, Mark Rutland, Arnd Bergmann,
Olof Johansson, Tomasz Figa, Mike Turquette, thomas.abraham,
Linus Walleij, Seung-Woo Kim, Kyungmin Park, InKi Dae,
geunsik.lim, jh80.chung, jaewon02.kim, ideal.song, yj44.cho
Hello,
On 2014-10-24 15:23, Daniel Drake wrote:
> On Sun, Oct 19, 2014 at 9:32 PM, Chanwoo Choi <cw00.choi@samsung.com> wrote:
>> This patch adds new exynos4415.dtsi to support Exynos4415 SoC
>> based on Cortex-A9 quad cores and includes following dt nodes:
> There's a lot in common between your new exynos4415.dtsi and the
> existing exynos4.dtsi.
> Would it make more sense for the 4415 code to extend the existing
> exynos4.dtsi like the other Exynos4 variants do?
Well, I also thought about such approach, but there are some fundamental
differences:
interrupt and clock controllers are completely different. Using a common
exynos4.dtsi
and overriding them in every node will result in a code, which is a bit
hard to follow.
IMHO with such differences justifies using separate base dtsi file.
Best regards
--
Marek Szyprowski, PhD
Samsung R&D Institute Poland
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 2/5] clk: samsung: exynos4415: Add clocks using common clock framework
2014-10-24 13:18 ` Daniel Drake
2014-10-24 13:28 ` Tomasz Figa
@ 2014-10-24 13:36 ` Chanwoo Choi
2014-10-24 13:56 ` Sylwester Nawrocki
2 siblings, 0 replies; 21+ messages in thread
From: Chanwoo Choi @ 2014-10-24 13:36 UTC (permalink / raw)
To: Daniel Drake
Cc: linux-samsung-soc, Linux Kernel, linux-arm-kernel, Kukjin Kim,
ben-linux, Russell King, Mark Rutland, Arnd Bergmann,
Olof Johansson, Tomasz Figa, Mike Turquette, thomas.abraham,
Linus Walleij, Seung-Woo Kim, Kyungmin Park, InKi Dae,
geunsik.lim, jh80.chung, jaewon02.kim, ideal.song, yj44.cho,
Sylwester Nawrocki
Hi Daniel,
On 10/24/2014 10:18 PM, Daniel Drake wrote:
> On Sun, Oct 19, 2014 at 9:32 PM, Chanwoo Choi <cw00.choi@samsung.com> wrote:
>> This patch adds the new clock driver of Exynos4415 SoC based on Cortex-A9
>> using common clock framework. The CMU (Clock Management Unit) of Exynos4415
>> controls PLLs(Phase Locked Loops) and generates system clocks for CPU, buses
>> and function clocks for individual IPs.
>
> There seems to be a lot in common here with other exynos4 variants in
> clk-exynos4.c. Have you considered just adding support for the 4415 in
> the existing driver?
Yes, It is difficult and to make existing clk-exynos4.c more complicated.
Exynos4415 has fewer difference from existing clk-exynos4.c and
different parent source of mux.
For exmaple about PLL,
There are different PLLs between Exynos4412 and Exynos4415.
- Exynos4412 has APLL, MPLL, EPLL, VPLL.
- Exynos4415 has APLL, EPLL, G3D_PLL, ISP_PLL, DISP_PLL and MPLL.
Also, MPLL of Exynos4415 was included in CMU_DMC scope.
Best Regards,
Chanwoo Choi
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 5/5] ARM: dts: Add dts files for Exynos4415 SoC
2014-10-24 13:34 ` Marek Szyprowski
@ 2014-10-24 13:44 ` Daniel Drake
0 siblings, 0 replies; 21+ messages in thread
From: Daniel Drake @ 2014-10-24 13:44 UTC (permalink / raw)
To: Marek Szyprowski
Cc: Chanwoo Choi, linux-samsung-soc, Linux Kernel, linux-arm-kernel,
Kukjin Kim, ben-linux, Russell King, Mark Rutland, Arnd Bergmann,
Olof Johansson, Tomasz Figa, Mike Turquette, thomas.abraham,
Linus Walleij, Seung-Woo Kim, Kyungmin Park, InKi Dae,
geunsik.lim, jh80.chung, jaewon02.kim, ideal.song, yj44.cho
On Fri, Oct 24, 2014 at 7:34 AM, Marek Szyprowski
<m.szyprowski@samsung.com> wrote:
> Well, I also thought about such approach, but there are some fundamental
> differences:
> interrupt and clock controllers are completely different. Using a common
> exynos4.dtsi
> and overriding them in every node will result in a code, which is a bit hard
> to follow.
> IMHO with such differences justifies using separate base dtsi file.
For the things that aren't in common, they are already split out into
soc-specific files for the existing Exynos4 variants. Taking your
example of the CMU, it already differs in different exynos4 versions
therefore is not listed in exynos4.dtsi at all.
So this argument only seems valid if the differences are really huge,
or if you are also saying the existing exynos4 dts files are bad?
Personally I have come to like the current layout, although would
definitely appreciate the reference-based syntax mentioned by Tomasz,
and this seems like a good opportunity to at least fix up exynos4.dtsi
for that.
Daniel
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 5/5] ARM: dts: Add dts files for Exynos4415 SoC
2014-10-24 13:23 ` Daniel Drake
2014-10-24 13:30 ` Tomasz Figa
2014-10-24 13:34 ` Marek Szyprowski
@ 2014-10-24 13:53 ` Chanwoo Choi
2 siblings, 0 replies; 21+ messages in thread
From: Chanwoo Choi @ 2014-10-24 13:53 UTC (permalink / raw)
To: Daniel Drake
Cc: linux-samsung-soc, Linux Kernel, linux-arm-kernel, Kukjin Kim,
ben-linux, Russell King, Mark Rutland, Arnd Bergmann,
Olof Johansson, Tomasz Figa, Mike Turquette, thomas.abraham,
Linus Walleij, Seung-Woo Kim, Kyungmin Park, InKi Dae,
geunsik.lim, jh80.chung, jaewon02.kim, ideal.song, yj44.cho,
Marek Szyprowski
Hi Daniel,
On 10/24/2014 10:23 PM, Daniel Drake wrote:
> On Sun, Oct 19, 2014 at 9:32 PM, Chanwoo Choi <cw00.choi@samsung.com> wrote:
>> This patch adds new exynos4415.dtsi to support Exynos4415 SoC
>> based on Cortex-A9 quad cores and includes following dt nodes:
>
> There's a lot in common between your new exynos4415.dtsi and the
> existing exynos4.dtsi.
> Would it make more sense for the 4415 code to extend the existing
> exynos4.dtsi like the other Exynos4 variants do?
I explained the difference between Exynos4415 and existing Exynos4 series
on mail-thread of exynos4415 clock controller.
Exynos4415 has difference clock id from existing Exynos4 clock controller.
because exynos4415 clock controller has fewer difference from Exynos4 series.
Best Regards,
Chanwoo Choi
^ permalink raw reply [flat|nested] 21+ messages in thread
* Re: [PATCH 2/5] clk: samsung: exynos4415: Add clocks using common clock framework
2014-10-24 13:18 ` Daniel Drake
2014-10-24 13:28 ` Tomasz Figa
2014-10-24 13:36 ` Chanwoo Choi
@ 2014-10-24 13:56 ` Sylwester Nawrocki
2 siblings, 0 replies; 21+ messages in thread
From: Sylwester Nawrocki @ 2014-10-24 13:56 UTC (permalink / raw)
To: Daniel Drake
Cc: Chanwoo Choi, linux-samsung-soc, Linux Kernel, linux-arm-kernel,
Kukjin Kim, ben-linux, Russell King, Mark Rutland, Arnd Bergmann,
Olof Johansson, Tomasz Figa, Mike Turquette, thomas.abraham,
Linus Walleij, Seung-Woo Kim, Kyungmin Park, InKi Dae,
geunsik.lim, jh80.chung, jaewon02.kim, ideal.song, yj44.cho
On 24/10/14 15:18, Daniel Drake wrote:
> On Sun, Oct 19, 2014 at 9:32 PM, Chanwoo Choi <cw00.choi@samsung.com> wrote:
>> > This patch adds the new clock driver of Exynos4415 SoC based on Cortex-A9
>> > using common clock framework. The CMU (Clock Management Unit) of Exynos4415
>> > controls PLLs(Phase Locked Loops) and generates system clocks for CPU, buses
>> > and function clocks for individual IPs.
>
> There seems to be a lot in common here with other exynos4 variants in
> clk-exynos4.c. Have you considered just adding support for the 4415 in
> the existing driver?
I would rather avoid mixing clock description tables for more SoCs in
clk-exynos4.c. There is quite a few differences between exynos4x12 and
exynos4415 clock controllers, I'm afraid merging exynos4415 support to
clk-exynos4.c would just create more branches and made the code harder
to follow, without much decrease in code size. The clock tree in single
SoC is already complex, without consolidating support for several SoCs
in one unit.
--
Regards,
Sylwester
^ permalink raw reply [flat|nested] 21+ messages in thread
end of thread, other threads:[~2014-10-24 13:56 UTC | newest]
Thread overview: 21+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-10-20 3:29 [PATCH 0/5] Support new Exynos4415 SoC based on Cortex-A9 quad cores Chanwoo Choi
2014-10-20 3:32 ` [PATCH 1/5] ARM: EXYNOS: Add EXYNOS4415 SoC ID Chanwoo Choi
2014-10-24 11:43 ` Tomasz Figa
2014-10-24 11:46 ` Chanwoo Choi
2014-10-20 3:32 ` [PATCH 2/5] clk: samsung: exynos4415: Add clocks using common clock framework Chanwoo Choi
2014-10-24 10:54 ` Sylwester Nawrocki
2014-10-24 10:59 ` Chanwoo Choi
2014-10-24 13:18 ` Daniel Drake
2014-10-24 13:28 ` Tomasz Figa
2014-10-24 13:36 ` Chanwoo Choi
2014-10-24 13:56 ` Sylwester Nawrocki
2014-10-20 3:32 ` [PATCH 3/5] clk: samsung: Document binding for Exynos4415 clock controller Chanwoo Choi
2014-10-24 10:32 ` Sylwester Nawrocki
2014-10-24 10:34 ` Chanwoo Choi
2014-10-20 3:32 ` [PATCH 4/5] pinctrl: exynos: Add support for Exynos4415 Chanwoo Choi
2014-10-20 3:32 ` [PATCH 5/5] ARM: dts: Add dts files for Exynos4415 SoC Chanwoo Choi
2014-10-24 13:23 ` Daniel Drake
2014-10-24 13:30 ` Tomasz Figa
2014-10-24 13:34 ` Marek Szyprowski
2014-10-24 13:44 ` Daniel Drake
2014-10-24 13:53 ` Chanwoo Choi
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).