* [PATCH v2 00/16] DTS for hi6220 and HiKey
@ 2016-04-02 9:29 Guodong Xu
2016-04-02 9:29 ` [PATCH v2 01/16] arm64: dts: Reserve memory regions for hi6220 Guodong Xu
` (15 more replies)
0 siblings, 16 replies; 34+ messages in thread
From: Guodong Xu @ 2016-04-02 9:29 UTC (permalink / raw)
To: xuwei5, mark.rutland, robh, grant.likely, linus.walleij, arnd.bergmann
Cc: devicetree, linux-kernel, linux-arm-kernel, kong.kongxinwei, Guodong Xu
This patchset include dts changes for hi6220 SoC and HiKey board. These
patches apply well one by one on top of next-20160401.
To avoid merge conflicts with patches already ack'ed by maintainers,
I picked all hi6220/hikey dts related patches into this single patchset.
And they passed the tests on HiKey.
Patch 1~3 are from hi6220 cpuidle support. It has been reviewed and
ack'ed in maillist.
[PATCH v2 RESEND 0/4] arm64: Hi6220: enable CPU idle states:
http://archive.arm.linux.org.uk/lurker/message/20160121.105346.7d3b0470.en.html
Patch 4~6 are for hi6220 gpio, pinctl and spi configurations respectively.
Patch 7 adds hi6220 i2c nodes, and
patch 8 enables them for hikey board usage.
Patch 9 adds add hi6220 usb node. It has been sent to maillist.
[PATCH] arm64: dts: add hi6220 usb node
http://thread.gmane.org/gmane.linux.drivers.devicetree/146062
http://thread.gmane.org/gmane.linux.drivers.devicetree/144335/focus=134022
Patch 10 and 11 are from hi6220 mailbox support. It has been reviewed and
ack'ed in maillist.
[PATCH v7 RESEND 0/4] mailbox: hisilicon: add Hi6220 mailbox driver
http://thread.gmane.org/gmane.linux.kernel/2152759/focus=2152768
Patch 12 adds pinctrl to uart ports in SoC and enables them for HiKey board.
Patch 13 adds gpio LEDs device nodes.
Patch 14 adds hi655x pmic dts node and regulator support.
[PATCH v8 5/5] arm64: dts: hisilicon: Add hi655x pmic dts node
http://thread.gmane.org/gmane.linux.kernel/2151688
Patch 15 adds dwmmc nodes description for hi6220. It refers to two LDO's
which are defined above.
Patch 16 adds wifi device node (TI's wl1835) for HiKey board.
v2:
- picked hi655x pmic dts node.
- removed dw_mmc resets property, as it is still under review.
- add 'non-removable' into dw_mmc2 for wifi
Chen Feng (1):
arm64: dts: hikey: Add hi655x pmic dts node
Guodong Xu (4):
arm64: dts: hikey: enable i2c0 and i2c1 for working with mezzanine
boards
arm64: dts: hi6220: add pinctrl for uarts and enable them
arm64: dts: add LED nodes for hi6220-hikey
arm64: dts: add wifi nodes support for hi6220-hikey
Leo Yan (5):
arm64: dts: Reserve memory regions for hi6220
arm64: dts: add sp804 timer node for Hi6220
arm64: dts: enable idle states for Hi6220
arm64: dts: add mailbox node for Hi6220
arm64: dts: add Hi6220's stub clock node
Xinwei Kong (2):
arm64: dts: add all hi6220 i2c nodes
arm64: dts: add dwmmc nodes for hi6220
Zhangfei Gao (1):
arm64: dts: add hi6220 usb node
Zhong Kaihua (3):
arm64: dts: Add Hi6220 gpio configuration nodes
arm64: dts: add Hi6220 pinctrl configuration nodes
arm64: dts: add Hi6220 spi configuration nodes
arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts | 198 ++++++-
arch/arm64/boot/dts/hisilicon/hi6220.dtsi | 582 +++++++++++++++++++
arch/arm64/boot/dts/hisilicon/hikey-gpio.dtsi | 607 +++++++++++++++++++
arch/arm64/boot/dts/hisilicon/hikey-pinctrl.dtsi | 705 +++++++++++++++++++++++
include/dt-bindings/pinctrl/hisi.h | 59 ++
5 files changed, 2147 insertions(+), 4 deletions(-)
create mode 100644 arch/arm64/boot/dts/hisilicon/hikey-gpio.dtsi
create mode 100644 arch/arm64/boot/dts/hisilicon/hikey-pinctrl.dtsi
create mode 100644 include/dt-bindings/pinctrl/hisi.h
--
1.9.1
^ permalink raw reply [flat|nested] 34+ messages in thread
* [PATCH v2 01/16] arm64: dts: Reserve memory regions for hi6220
2016-04-02 9:29 [PATCH v2 00/16] DTS for hi6220 and HiKey Guodong Xu
@ 2016-04-02 9:29 ` Guodong Xu
2016-04-02 9:29 ` [PATCH v2 02/16] arm64: dts: add sp804 timer node for Hi6220 Guodong Xu
` (14 subsequent siblings)
15 siblings, 0 replies; 34+ messages in thread
From: Guodong Xu @ 2016-04-02 9:29 UTC (permalink / raw)
To: xuwei5, mark.rutland, robh, grant.likely, linus.walleij, arnd.bergmann
Cc: devicetree, linux-kernel, linux-arm-kernel, kong.kongxinwei, Leo Yan
From: Leo Yan <leo.yan@linaro.org>
On Hi6220, below memory regions in DDR have specific purpose:
0x05e0,0000 - 0x05ef,ffff: For MCU firmware using at runtime;
0x06df,f000 - 0x06df,ffff: For mailbox message data;
0x0740,f000 - 0x0740,ffff: For MCU firmware's section;
0x3e00,0000 - 0x3fff,ffff: For OP-TEE.
This patch reserves these memory regions in DT.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
---
arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts | 16 ++++++++++++----
1 file changed, 12 insertions(+), 4 deletions(-)
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
index 8185251..17bd793 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
@@ -7,9 +7,6 @@
/dts-v1/;
-/*Reserved 1MB memory for MCU*/
-/memreserve/ 0x05e00000 0x00100000;
-
#include "hi6220.dtsi"
/ {
@@ -27,9 +24,20 @@
stdout-path = "serial3:115200n8";
};
+ /*
+ * Reserve below regions from memory node:
+ *
+ * 0x05e0,0000 - 0x05ef,ffff: MCU firmware runtime using
+ * 0x06df,f000 - 0x06df,ffff: Mailbox message data
+ * 0x0740,f000 - 0x0740,ffff: MCU firmware section
+ * 0x3e00,0000 - 0x3fff,ffff: OP-TEE
+ */
memory@0 {
device_type = "memory";
- reg = <0x0 0x0 0x0 0x40000000>;
+ reg = <0x00000000 0x00000000 0x00000000 0x05e00000>,
+ <0x00000000 0x05f00000 0x00000000 0x00eff000>,
+ <0x00000000 0x06e00000 0x00000000 0x0060f000>,
+ <0x00000000 0x07410000 0x00000000 0x36bf0000>;
};
};
--
1.9.1
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v2 02/16] arm64: dts: add sp804 timer node for Hi6220
2016-04-02 9:29 [PATCH v2 00/16] DTS for hi6220 and HiKey Guodong Xu
2016-04-02 9:29 ` [PATCH v2 01/16] arm64: dts: Reserve memory regions for hi6220 Guodong Xu
@ 2016-04-02 9:29 ` Guodong Xu
2016-04-03 19:23 ` Linus Walleij
2016-04-02 9:29 ` [PATCH v2 03/16] arm64: dts: enable idle states " Guodong Xu
` (13 subsequent siblings)
15 siblings, 1 reply; 34+ messages in thread
From: Guodong Xu @ 2016-04-02 9:29 UTC (permalink / raw)
To: xuwei5, mark.rutland, robh, grant.likely, linus.walleij, arnd.bergmann
Cc: devicetree, linux-kernel, linux-arm-kernel, kong.kongxinwei, Leo Yan
From: Leo Yan <leo.yan@linaro.org>
Add sp804 timer for hi6220, so it can be used as broadcast timer.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
---
arch/arm64/boot/dts/hisilicon/hi6220.dtsi | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
index ad1f1eb..82c4756 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
@@ -209,5 +209,14 @@
clock-names = "uartclk", "apb_pclk";
status = "disabled";
};
+
+ dual_timer0: dual_timer@f8008000 {
+ compatible = "arm,sp804", "arm,primecell";
+ reg = <0x0 0xf8008000 0x0 0x1000>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ao_ctrl 27>;
+ clock-names = "apb_pclk";
+ };
};
};
--
1.9.1
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v2 03/16] arm64: dts: enable idle states for Hi6220
2016-04-02 9:29 [PATCH v2 00/16] DTS for hi6220 and HiKey Guodong Xu
2016-04-02 9:29 ` [PATCH v2 01/16] arm64: dts: Reserve memory regions for hi6220 Guodong Xu
2016-04-02 9:29 ` [PATCH v2 02/16] arm64: dts: add sp804 timer node for Hi6220 Guodong Xu
@ 2016-04-02 9:29 ` Guodong Xu
2016-04-02 9:29 ` [PATCH v2 04/16] arm64: dts: Add Hi6220 gpio configuration nodes Guodong Xu
` (12 subsequent siblings)
15 siblings, 0 replies; 34+ messages in thread
From: Guodong Xu @ 2016-04-02 9:29 UTC (permalink / raw)
To: xuwei5, mark.rutland, robh, grant.likely, linus.walleij, arnd.bergmann
Cc: devicetree, linux-kernel, linux-arm-kernel, kong.kongxinwei, Leo Yan
From: Leo Yan <leo.yan@linaro.org>
Add cpu and cluster level's low power state for Hi6220.
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
---
arch/arm64/boot/dts/hisilicon/hi6220.dtsi | 31 +++++++++++++++++++++++++++++++
1 file changed, 31 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
index 82c4756..2585236 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
@@ -53,11 +53,35 @@
};
};
+ idle-states {
+ entry-method = "psci";
+
+ CPU_SLEEP: cpu-sleep {
+ compatible = "arm,idle-state";
+ local-timer-stop;
+ arm,psci-suspend-param = <0x0010000>;
+ entry-latency-us = <700>;
+ exit-latency-us = <250>;
+ min-residency-us = <1000>;
+ };
+
+ CLUSTER_SLEEP: cluster-sleep {
+ compatible = "arm,idle-state";
+ local-timer-stop;
+ arm,psci-suspend-param = <0x1010000>;
+ entry-latency-us = <1000>;
+ exit-latency-us = <700>;
+ min-residency-us = <2700>;
+ wakeup-latency-us = <1500>;
+ };
+ };
+
cpu0: cpu@0 {
compatible = "arm,cortex-a53", "arm,armv8";
device_type = "cpu";
reg = <0x0 0x0>;
enable-method = "psci";
+ cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP>;
};
cpu1: cpu@1 {
@@ -65,6 +89,7 @@
device_type = "cpu";
reg = <0x0 0x1>;
enable-method = "psci";
+ cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP>;
};
cpu2: cpu@2 {
@@ -72,6 +97,7 @@
device_type = "cpu";
reg = <0x0 0x2>;
enable-method = "psci";
+ cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP>;
};
cpu3: cpu@3 {
@@ -79,6 +105,7 @@
device_type = "cpu";
reg = <0x0 0x3>;
enable-method = "psci";
+ cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP>;
};
cpu4: cpu@100 {
@@ -86,6 +113,7 @@
device_type = "cpu";
reg = <0x0 0x100>;
enable-method = "psci";
+ cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP>;
};
cpu5: cpu@101 {
@@ -93,6 +121,7 @@
device_type = "cpu";
reg = <0x0 0x101>;
enable-method = "psci";
+ cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP>;
};
cpu6: cpu@102 {
@@ -100,6 +129,7 @@
device_type = "cpu";
reg = <0x0 0x102>;
enable-method = "psci";
+ cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP>;
};
cpu7: cpu@103 {
@@ -107,6 +137,7 @@
device_type = "cpu";
reg = <0x0 0x103>;
enable-method = "psci";
+ cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP>;
};
};
--
1.9.1
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v2 04/16] arm64: dts: Add Hi6220 gpio configuration nodes
2016-04-02 9:29 [PATCH v2 00/16] DTS for hi6220 and HiKey Guodong Xu
` (2 preceding siblings ...)
2016-04-02 9:29 ` [PATCH v2 03/16] arm64: dts: enable idle states " Guodong Xu
@ 2016-04-02 9:29 ` Guodong Xu
2016-04-03 19:28 ` Linus Walleij
2016-04-02 9:29 ` [PATCH v2 05/16] arm64: dts: add Hi6220 pinctrl " Guodong Xu
` (11 subsequent siblings)
15 siblings, 1 reply; 34+ messages in thread
From: Guodong Xu @ 2016-04-02 9:29 UTC (permalink / raw)
To: xuwei5, mark.rutland, robh, grant.likely, linus.walleij, arnd.bergmann
Cc: devicetree, linux-kernel, linux-arm-kernel, kong.kongxinwei,
Zhong Kaihua
From: Zhong Kaihua <zhongkaihua@huawei.com>
Add Hi6220 gpio configuration nodes
Signed-off-by: Zhong Kaihua <zhongkaihua@huawei.com>
Signed-off-by: Kong Xinwei <kong.kongxinwei@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
---
arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts | 1 +
arch/arm64/boot/dts/hisilicon/hi6220.dtsi | 259 +++++++++++
arch/arm64/boot/dts/hisilicon/hikey-gpio.dtsi | 607 +++++++++++++++++++++++++
3 files changed, 867 insertions(+)
create mode 100644 arch/arm64/boot/dts/hisilicon/hikey-gpio.dtsi
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
index 17bd793..f9b2d1e 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
@@ -8,6 +8,7 @@
/dts-v1/;
#include "hi6220.dtsi"
+#include "hikey-gpio.dtsi"
/ {
model = "HiKey Development Board";
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
index 2585236..ad7074d 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
@@ -249,5 +249,264 @@
clocks = <&ao_ctrl 27>;
clock-names = "apb_pclk";
};
+
+ gpio0: gpio@f8011000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0x0 0xf8011000 0x0 0x1000>;
+ interrupts = <0 52 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&ao_ctrl 2>;
+ clock-names = "apb_pclk";
+ status = "ok";
+ };
+
+ gpio1: gpio@f8012000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0x0 0xf8012000 0x0 0x1000>;
+ interrupts = <0 53 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&ao_ctrl 2>;
+ clock-names = "apb_pclk";
+ status = "ok";
+ };
+
+ gpio2: gpio@f8013000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0x0 0xf8013000 0x0 0x1000>;
+ interrupts = <0 54 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&ao_ctrl 2>;
+ clock-names = "apb_pclk";
+ status = "ok";
+ };
+
+ gpio3: gpio@f8014000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0x0 0xf8014000 0x0 0x1000>;
+ interrupts = <0 55 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&ao_ctrl 2>;
+ clock-names = "apb_pclk";
+ status = "ok";
+ };
+
+ gpio4: gpio@f7020000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0x0 0xf7020000 0x0 0x1000>;
+ interrupts = <0 56 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&ao_ctrl 2>;
+ clock-names = "apb_pclk";
+ status = "ok";
+ };
+
+ gpio5: gpio@f7021000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0x0 0xf7021000 0x0 0x1000>;
+ interrupts = <0 57 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&ao_ctrl 2>;
+ clock-names = "apb_pclk";
+ status = "ok";
+ };
+
+ gpio6: gpio@f7022000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0x0 0xf7022000 0x0 0x1000>;
+ interrupts = <0 58 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&ao_ctrl 2>;
+ clock-names = "apb_pclk";
+ status = "ok";
+ };
+
+ gpio7: gpio@f7023000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0x0 0xf7023000 0x0 0x1000>;
+ interrupts = <0 59 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&ao_ctrl 2>;
+ clock-names = "apb_pclk";
+ status = "ok";
+ };
+
+ gpio8: gpio@f7024000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0x0 0xf7024000 0x0 0x1000>;
+ interrupts = <0 60 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&ao_ctrl 2>;
+ clock-names = "apb_pclk";
+ status = "ok";
+ };
+
+ gpio9: gpio@f7025000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0x0 0xf7025000 0x0 0x1000>;
+ interrupts = <0 61 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&ao_ctrl 2>;
+ clock-names = "apb_pclk";
+ status = "ok";
+ };
+
+ gpio10: gpio@f7026000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0x0 0xf7026000 0x0 0x1000>;
+ interrupts = <0 62 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&ao_ctrl 2>;
+ clock-names = "apb_pclk";
+ status = "ok";
+ };
+
+ gpio11: gpio@f7027000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0x0 0xf7027000 0x0 0x1000>;
+ interrupts = <0 63 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&ao_ctrl 2>;
+ clock-names = "apb_pclk";
+ status = "ok";
+ };
+
+ gpio12: gpio@f7028000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0x0 0xf7028000 0x0 0x1000>;
+ interrupts = <0 64 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&ao_ctrl 2>;
+ clock-names = "apb_pclk";
+ status = "ok";
+ };
+
+ gpio13: gpio@f7029000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0x0 0xf7029000 0x0 0x1000>;
+ interrupts = <0 65 0x4>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&ao_ctrl 2>;
+ clock-names = "apb_pclk";
+ status = "ok";
+ };
+
+ gpio14: gpio@f702a000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0x0 0xf702a000 0x0 0x1000>;
+ interrupts = <0 66 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&ao_ctrl 2>;
+ clock-names = "apb_pclk";
+ status = "ok";
+ };
+
+ gpio15: gpio@f702b000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0x0 0xf702b000 0x0 0x1000>;
+ interrupts = <0 67 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&ao_ctrl 2>;
+ clock-names = "apb_pclk";
+ status = "ok";
+ };
+
+ gpio16: gpio@f702c000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0x0 0xf702c000 0x0 0x1000>;
+ interrupts = <0 68 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&ao_ctrl 2>;
+ clock-names = "apb_pclk";
+ status = "ok";
+ };
+
+ gpio17: gpio@f702d000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0x0 0xf702d000 0x0 0x1000>;
+ interrupts = <0 69 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&ao_ctrl 2>;
+ clock-names = "apb_pclk";
+ status = "ok";
+ };
+
+ gpio18: gpio@f702e000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0x0 0xf702e000 0x0 0x1000>;
+ interrupts = <0 70 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&ao_ctrl 2>;
+ clock-names = "apb_pclk";
+ status = "ok";
+ };
+
+ gpio19: gpio@f702f000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0x0 0xf702f000 0x0 0x1000>;
+ interrupts = <0 71 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&ao_ctrl 2>;
+ clock-names = "apb_pclk";
+ status = "ok";
+ };
};
};
diff --git a/arch/arm64/boot/dts/hisilicon/hikey-gpio.dtsi b/arch/arm64/boot/dts/hisilicon/hikey-gpio.dtsi
new file mode 100644
index 0000000..09242f0
--- /dev/null
+++ b/arch/arm64/boot/dts/hisilicon/hikey-gpio.dtsi
@@ -0,0 +1,607 @@
+/ {
+ gpio_rstout_n:gpio_rstout_n {
+ gpios;
+ };
+ gpio_pmu_peri_en:gpio_pmu_peri_en {
+ gpios;
+ };
+ gpio_sysclk0_en:gpio_sysclk0_en {
+ gpios;
+ };
+ gpio_jtag_tdo:gpio_jtag_tdo {
+ gpios;
+ };
+ /* LCB: PWR_HOLD_GPIO0_0 */
+ gpio_pwr_hold:gpio_pwr_hold {
+ gpios = <&gpio0 0 0>;
+ };
+ /* LCB: DSI_SEL_GPIO0_1 */
+ gpio_dsi_sel:gpio_dsi_sel {
+ gpios = <&gpio0 1 0>;
+ };
+ /* LCB: USB_HUB_RESET_N_GPIO0_2 */
+ gpio_usb_hub_reset_n:gpio_usb_hub_reset_n {
+ gpios = <&gpio0 2 0>;
+ };
+ /* LCB: USB_SEL_GPIO0_3 */
+ gpio_usb_sel:gpio_usb_sel {
+ gpios = <&gpio0 3 0>;
+ };
+ /* LCB: HDMI_PD_GPIO0_4 */
+ gpio_hdmi_pd:gpio_hdmi_pd {
+ gpios = <&gpio0 4 0>;
+ };
+ /* LCB: WL_REG_ON_GPIO0_5 */
+ gpio_wl_en:gpio_wl_en {
+ gpios = <&gpio0 5 0>;
+ };
+ /* LCB: PWRON_DET_GPIO0_6 */
+ gpio_pwron_det:gpio_pwron_det {
+ gpios = <&gpio0 6 0>;
+ };
+ /* LCB: 5V_HUB_EN_GPIO0_7 */
+ gpio_usb_dev_det:gpio_usb_dev_det {
+ gpios = <&gpio0 7 0>;
+ };
+ /* LCB: SD_DET_GPIO1_0 */
+ gpio_sd_det:gpio_sd_det {
+ gpios = <&gpio1 0 0>;
+ };
+ /* LCB: HDMI_INT_GPIO1_1 */
+ gpio_hdmi_int:gpio_hdmi_int {
+ gpios = <&gpio1 1 0>;
+ };
+ /* LCB: PMU_IRQ_N_GPIO1_2 */
+ gpio_pmu_irq_n:gpio_pmu_irq_n {
+ gpios = <&gpio1 2 0>;
+ };
+ /* LCB: WL_HOST_WAKE_GPIO1_3 */
+ gpio_wl_host_wake:gpio_wl_host_wake {
+ gpios = <&gpio1 3 0>;
+ };
+ gpio_nfc_int:gpio_nfc_int {
+ gpios = <&gpio1 4 0>;
+ };
+ gpio_unused_001:gpio_unused_001 {
+ gpios = <&gpio1 5 0>;
+ };
+ /* LCB: BT_REG_ON_GPIO1_7 */
+ gpio_bt_reg_on:gpio_bt_reg_on {
+ gpios = <&gpio1 7 0>;
+ };
+ /* LCB: GPIO2_0, J2 */
+ gpio_j2_2_0:gpio_j2_2_0 {
+ gpios = <&gpio2 0 0>;
+ };
+ /* LCB: GPIO2_1, J2 */
+ gpio_j2_2_1:gpio_j2_2_1 {
+ gpios = <&gpio2 1 0>;
+ };
+ /* LCB: GPIO2_2, J2 */
+ gpio_j2_2_2:gpio_j2_2_2 {
+ gpios = <&gpio2 2 0>;
+ };
+ /* LCB: GPIO2_3, J2 */
+ gpio_j2_2_3:gpio_j2_2_3 {
+ gpios = <&gpio2 3 0>;
+ };
+ /* LCB: GPIO2_4, J2 */
+ gpio_j2_2_4:gpio_j2_2_4 {
+ gpios = <&gpio2 4 0>;
+ };
+ /* LCB: USB_ID_DET_GPIO2_5 */
+ gpio_usb_id_det:gpio_usb_id_det {
+ gpios = <&gpio2 5 0>;
+ };
+ /* LCB: USB_VBUS_DET_GPIO2_6 */
+ gpio_vbus_det:gpio_vbus_det {
+ gpios = <&gpio2 6 0>;
+ };
+ /* LCB: GPIO2_7, J2 */
+ gpio_j2_2_7:gpio_j2_2_7 {
+ gpios = <&gpio2 7 0>;
+ };
+ gpio_rf_reset0:gpio_rf_reset0 {
+ gpios;
+ };
+ gpio_rf_reset1:gpio_rf_reset1 {
+ gpios;
+ };
+ gpio_boot_sel:gpio_boot_sel {
+ gpios = <&gpio10 0 0>;
+ };
+ gpio_pmu_ssi:gpio_pmu_ssi {
+ gpios;
+ };
+ gpio_gps_ref_clk:gpio_gps_ref_clk {
+ gpios = <&gpio8 2 0>;
+ };
+ gpio_sd_clk:gpio_sd_clk {
+ gpios = <&gpio8 3 0>;
+ };
+ gpio_sd_cmd:gpio_sd_cmd {
+ gpios = <&gpio8 4 0>;
+ };
+ gpio_sd_data0:gpio_sd_data0 {
+ gpios = <&gpio8 5 0>;
+ };
+ gpio_sd_data1:gpio_sd_data1 {
+ gpios = <&gpio8 6 0>;
+ };
+ gpio_sd_data2:gpio_sd_data2 {
+ gpios = <&gpio8 7 0>;
+ };
+ gpio_sd_data3:gpio_sd_data3 {
+ gpios = <&gpio9 0 0>;
+ };
+ gpio_unused_002:gpio_unused_002 {
+ gpios;
+ };
+ gpio_mcam_pwdn:gpio_mcam_pwdn {
+ gpios = <&gpio9 1 0>;
+ };
+ gpio_vcm_pwdn:gpio_vcm_pwdn {
+ gpios = <&gpio9 2 0>;
+ };
+ gpio_scam_pwdn:gpio_scam_pwdn {
+ gpios = <&gpio9 3 0>;
+ };
+ gpio_cam_id0:gpio_cam_id0 {
+ gpios = <&gpio9 4 0>;
+ };
+ gpio_cam_id1:gpio_cam_id1 {
+ gpios = <&gpio9 5 0>;
+ };
+ gpio_flash_strobe:gpio_flash_strobe {
+ gpios = <&gpio9 6 0>;
+ };
+ gpio_mcam_mclk:gpio_mcam_mclk {
+ gpios = <&gpio9 7 0>;
+ };
+ gpio_scam_mclk:gpio_scam_mclk {
+ gpios = <&gpio10 1 0>;
+ };
+ gpio_cam_reset0:gpio_cam_reset0 {
+ gpios = <&gpio10 2 0>;
+ };
+ gpio_cam_reset1:gpio_cam_reset1 {
+ gpios = <&gpio10 3 0>;
+ };
+ gpio_tp_rst_n:gpio_tp_rst_n {
+ gpios = <&gpio10 4 0>;
+ };
+ gpio_unused_003:gpio_unused_003 {
+ gpios = <&gpio10 5 0>;
+ };
+ gpio_isp_sda0:gpio_isp_sda0 {
+ gpios = <&gpio10 6 0>;
+ };
+ gpio_isp_scl0:gpio_isp_scl0 {
+ gpios = <&gpio10 7 0>;
+ };
+ gpio_isp_sda1:gpio_isp_sda1 {
+ gpios = <&gpio11 0 0>;
+ };
+ gpio_isp_scl1:gpio_isp_scl1 {
+ gpios = <&gpio11 1 0>;
+ };
+ gpio_mdm_rst:gpio_mdm_rst {
+ gpios = <&gpio11 2 0>;
+ };
+ gpio_hkadc_ssi:gpio_hkadc_ssi {
+ gpios;
+ };
+ gpio_codec_clk:gpio_codec_clk {
+ gpios;
+ };
+ gpio_ap_wakeup_mdm:gpio_ap_wakeup_mdm {
+ gpios = <&gpio11 3 0>;
+ };
+ gpio_codec_sync:gpio_codec_sync {
+ gpios = <&gpio11 4 0>;
+ };
+ gpio_codec_datain:gpio_codec_datain {
+ gpios = <&gpio11 5 0>;
+ };
+ gpio_codec_dataout:gpio_codec_dataout {
+ gpios = <&gpio11 6 0>;
+ };
+ gpio_fm_xclk:gpio_fm_xclk {
+ gpios = <&gpio11 7 0>;
+ };
+ gpio_fm_xfs:gpio_fm_xfs {
+ gpios = <&gpio12 0 0>;
+ };
+ gpio_fm_di:gpio_fm_di {
+ gpios = <&gpio12 1 0>;
+ };
+ gpio_fm_do:gpio_fm_do {
+ gpios = <&gpio12 2 0>;
+ };
+ gpio_bt_xclk:gpio_bt_xclk {
+ gpios;
+ };
+ gpio_bt_xfs:gpio_bt_xfs {
+ gpios;
+ };
+ gpio_bt_di:gpio_bt_di {
+ gpios;
+ };
+ gpio_bt_do:gpio_bt_do {
+ gpios;
+ };
+ gpio_usim0_clk:gpio_usim0_clk {
+ gpios;
+ };
+ gpio_usim0_data:gpio_usim0_data {
+ gpios;
+ };
+ gpio_usim0_rst:gpio_usim0_rst {
+ gpios;
+ };
+ gpio_usim1_clk:gpio_usim1_clk {
+ gpios = <&gpio12 3 0>;
+ };
+ gpio_usim1_data:gpio_usim1_data {
+ gpios = <&gpio12 4 0>;
+ };
+ gpio_usim1_rst:gpio_usim1_rst {
+ gpios = <&gpio12 5 0>;
+ };
+ gpio_unused_004:gpio_unused_004 {
+ gpios = <&gpio12 6 0>;
+ };
+ gpio_unused_005:gpio_unused_005 {
+ gpios = <&gpio12 7 0>;
+ };
+ gpio_uart0_rxd:gpio_uart0_rxd {
+ gpios = <&gpio13 0 0>;
+ };
+ gpio_uart0_txd:gpio_uart0_txd {
+ gpios = <&gpio13 1 0>;
+ };
+ gpio_bt_uart_cts_n:gpio_bt_uart_cts_n {
+ gpios = <&gpio13 2 0>;
+ };
+ gpio_bt_uart_rts_n:gpio_bt_uart_rts_n {
+ gpios = <&gpio13 3 0>;
+ };
+ gpio_bt_uart_rxd:gpio_bt_uart_rxd {
+ gpios = <&gpio13 4 0>;
+ };
+ gpio_bt_uart_txd:gpio_bt_uart_txd {
+ gpios = <&gpio13 5 0>;
+ };
+ gpio_gps_uart_cts_n:gpio_gps_uart_cts_n {
+ gpios = <&gpio13 6 0>;
+ };
+ gpio_gps_uart_rts_n:gpio_gps_uart_rts_n {
+ gpios = <&gpio13 7 0>;
+ };
+ gpio_gps_uart_rxd:gpio_gps_uart_rxd {
+ gpios = <&gpio14 0 0>;
+ };
+ gpio_gps_uart_txd:gpio_gps_uart_txd {
+ gpios = <&gpio14 1 0>;
+ };
+ gpio_i2c0_scl:gpio_i2c0_scl {
+ gpios = <&gpio14 2 0>;
+ };
+ gpio_i2c0_sda:gpio_i2c0_sda {
+ gpios = <&gpio14 3 0>;
+ };
+ gpio_i2c1_scl:gpio_i2c1_scl {
+ gpios = <&gpio14 4 0>;
+ };
+ gpio_i2c1_sda:gpio_i2c1_sda {
+ gpios = <&gpio14 5 0>;
+ };
+ gpio_i2c2_scl:gpio_i2c2_scl {
+ gpios = <&gpio14 6 0>;
+ };
+ gpio_i2c2_sda:gpio_i2c2_sda {
+ gpios = <&gpio14 7 0>;
+ };
+ gpio_emmc_clk:gpio_emmc_clk {
+ gpios;
+ };
+ gpio_emmc_cmd:gpio_emmc_cmd {
+ gpios;
+ };
+ gpio_emmc_data0:gpio_emmc_data0 {
+ gpios;
+ };
+ gpio_emmc_data1:gpio_emmc_data1 {
+ gpios;
+ };
+ gpio_emmc_data2:gpio_emmc_data2 {
+ gpios;
+ };
+ gpio_emmc_data3:gpio_emmc_data3 {
+ gpios;
+ };
+ gpio_emmc_data4:gpio_emmc_data4 {
+ gpios;
+ };
+ gpio_emmc_data5:gpio_emmc_data5 {
+ gpios;
+ };
+ gpio_emmc_data6:gpio_emmc_data6 {
+ gpios;
+ };
+ gpio_emmc_data7:gpio_emmc_data7 {
+ gpios;
+ };
+ gpio_emmc_rst_n:gpio_emmc_rst_n {
+ gpios;
+ };
+ gpio_unused_006:gpio_unused_006 {
+ gpios;
+ };
+ gpio_sdio_clk:gpio_sdio_clk {
+ gpios = <&gpio15 0 0>;
+ };
+ gpio_sdio_cmd:gpio_sdio_cmd {
+ gpios = <&gpio15 1 0>;
+ };
+ gpio_sdio_data0:gpio_sdio_data0 {
+ gpios = <&gpio15 2 0>;
+ };
+ gpio_sdio_data1:gpio_sdio_data1 {
+ gpios = <&gpio15 3 0>;
+ };
+ gpio_sdio_data2:gpio_sdio_data2 {
+ gpios = <&gpio15 4 0>;
+ };
+ gpio_sdio_data3:gpio_sdio_data3 {
+ gpios = <&gpio15 5 0>;
+ };
+ gpio_unused_007:gpio_unused_007 {
+ gpios;
+ };
+ /* LCB: GPIO3_0, on J15, as general purpose input */
+ gpio_j15_3_0:gpio_j15_3_0 {
+ gpios = <&gpio3 0 0>;
+ };
+ gpio_jtag_sel0:gpio_jtag_sel0 {
+ gpios = <&gpio3 1 0>;
+ };
+ gpio_jtag_sel1:gpio_jtag_sel1 {
+ gpios = <&gpio3 2 0>;
+ };
+ gpio_lcd_rst_n:gpio_lcd_rst_n {
+ gpios = <&gpio3 3 0>;
+ };
+ gpio_aux_ssi0:gpio_aux_ssi0 {
+ gpios = <&gpio3 4 0>;
+ };
+ /* LCB: WLAN_ACTIVE_GPIO3_5, connects to led, as general purpose */
+ gpio_wlan_active_led:gpio_wlan_active_led {
+ gpios = <&gpio3 5 0>;
+ };
+ gpio_unused_008:gpio_unused_008 {
+ gpios = <&gpio3 6 0>;
+ };
+ gpio_ap_wakeup_bt:gpio_ap_wakeup_bt {
+ gpios = <&gpio3 7 0>;
+ };
+ /* LCB: USER_LED1_GPIO4_0 */
+ gpio_user_led_1:gpio_user_led_1 {
+ gpios = <&gpio4 0 0>;
+ };
+ /* LCB: USER_LED1_GPIO4_1 */
+ gpio_user_led_2:gpio_user_led_2 {
+ gpios = <&gpio4 1 0>;
+ };
+ /* LCB: USER_LED1_GPIO4_2 */
+ gpio_user_led_3:gpio_user_led_3 {
+ gpios = <&gpio4 2 0>;
+ };
+ /* LCB: USER_LED1_GPIO4_3 */
+ gpio_user_led_4:gpio_user_led_4 {
+ gpios = <&gpio4 3 0>;
+ };
+ gpio_i2c3_scl:gpio_i2c3_scl {
+ gpios = <&gpio4 4 0>;
+ };
+ gpio_i2c3_sda:gpio_i2c3_sda {
+ gpios = <&gpio4 5 0>;
+ };
+ gpio_wlan_bt_priority:gpio_wlan_bt_priority {
+ gpios = <&gpio4 6 0>;
+ };
+ /* LCB: BT_ACTIVE_GPIO4_7, connects to led, as general purpose */
+ gpio_bt_active_led:gpio_bt_active_led {
+ gpios = <&gpio4 7 0>;
+ };
+ gpio_uart3_cts_n:gpio_uart3_cts_n {
+ gpios = <&gpio5 0 0>;
+ };
+ gpio_uart3_rts_n:gpio_uart3_rts_n {
+ gpios = <&gpio5 1 0>;
+ };
+ gpio_uart3_rxd:gpio_uart3_rxd {
+ gpios = <&gpio5 2 0>;
+ };
+ gpio_uart3_txd:gpio_uart3_txd {
+ gpios = <&gpio5 3 0>;
+ };
+ gpio_aux_ssi1:gpio_aux_ssi1 {
+ gpios = <&gpio5 4 0>;
+ };
+ gpio_unused_009:gpio_unused_009 {
+ gpios = <&gpio5 5 0>;
+ };
+ gpio_modem_pcm_xclk:gpio_modem_pcm_xclk {
+ gpios = <&gpio5 6 0>;
+ };
+ gpio_modem_pcm_xfs:gpio_modem_pcm_xfs {
+ gpios = <&gpio5 7 0>;
+ };
+ gpio_spi0_di:gpio_spi0_di {
+ gpios = <&gpio6 0 0>;
+ };
+ gpio_spi0_do:gpio_spi0_do {
+ gpios = <&gpio6 1 0>;
+ };
+ gpio_spi0_cs_n:gpio_spi0_cs_n {
+ gpios = <&gpio6 2 0>;
+ };
+ gpio_spi0_clk:gpio_spi0_clk {
+ gpios = <&gpio6 3 0>;
+ };
+ gpio_lte_tx_active:gpio_lte_tx_active {
+ gpios = <&gpio6 4 0>;
+ };
+ gpio_lte_rx_active:gpio_lte_rx_active {
+ gpios = <&gpio6 5 0>;
+ };
+ gpio_lcd_id0:gpio_lcd_id0 {
+ gpios = <&gpio6 6 0>;
+ };
+ /* LCB: GPIO6_7_DSI_TE0 */
+ gpio_dsi_te0:gpio_dsi_te0 {
+ gpios = <&gpio6 7 0>;
+ };
+ gpio_lcd_id1:gpio_lcd_id1 {
+ gpios = <&gpio7 0 0>;
+ };
+ gpio_volume1_n:gpio_volume1_n {
+ gpios = <&gpio7 1 0>;
+ };
+ gpio_uart5_rxd:gpio_uart5_rxd {
+ gpios = <&gpio7 2 0>;
+ };
+ gpio_uart5_txd:gpio_uart5_txd {
+ gpios = <&gpio7 3 0>;
+ };
+ gpio_modem_pcm_di:gpio_modem_pcm_di {
+ gpios = <&gpio7 4 0>;
+ };
+ gpio_modem_pcm_do:gpio_modem_pcm_do {
+ gpios = <&gpio7 5 0>;
+ };
+ gpio_uart4_rxd:gpio_uart4_rxd {
+ gpios = <&gpio7 6 0>;
+ };
+ gpio_uart4_txd:gpio_uart4_txd {
+ gpios = <&gpio7 7 0>;
+ };
+ gpio_ap_wakeup_wl:gpio_ap_wakeup_wl {
+ gpios = <&gpio8 0 0>;
+ };
+ gpio_mdm_pwr_en:gpio_mdm_pwr_en {
+ gpios = <&gpio8 1 0>;
+ };
+ gpio_tcxo0_afc:gpio_tcxo0_afc {
+ gpios = <&gpio15 6 0>;
+ };
+ gpio_rf_ssi0:gpio_rf_ssi0 {
+ gpios;
+ };
+ gpio_rf_tcvr_on0:gpio_rf_tcvr_on0 {
+ gpios;
+ };
+ gpio_rf_mipi_clk0:gpio_rf_mipi_clk0 {
+ gpios;
+ };
+ gpio_rf_mipi_data0:gpio_rf_mipi_data0 {
+ gpios = <&gpio15 7 0>;
+ };
+ gpio_flash_mask:gpio_flash_mask {
+ gpios = <&gpio16 0 0>;
+ };
+ gpio_gps_blanking:gpio_gps_blanking {
+ gpios = <&gpio16 1 0>;
+ };
+ gpio_rf_gpio_2:gpio_rf_gpio_2 {
+ gpios = <&gpio16 2 0>;
+ };
+ gpio_rf_gpio_3:gpio_rf_gpio_3 {
+ gpios = <&gpio16 3 0>;
+ };
+ gpio_rf_gpio_4:gpio_rf_gpio_4 {
+ gpios = <&gpio16 4 0>;
+ };
+ gpio_rf_gpio_5:gpio_rf_gpio_5 {
+ gpios = <&gpio16 5 0>;
+ };
+ gpio_rf_gpio_6:gpio_rf_gpio_6 {
+ gpios = <&gpio16 6 0>;
+ };
+ gpio_rf_gpio_7:gpio_rf_gpio_7 {
+ gpios = <&gpio16 7 0>;
+ };
+ gpio_rf_gpio_8:gpio_rf_gpio_8 {
+ gpios = <&gpio17 0 0>;
+ };
+ gpio_rf_gpio_9:gpio_rf_gpio_9 {
+ gpios = <&gpio17 1 0>;
+ };
+ gpio_rf_gpio_10:gpio_rf_gpio_10 {
+ gpios = <&gpio17 2 0>;
+ };
+ gpio_rf_gpio_11:gpio_rf_gpio_11 {
+ gpios = <&gpio17 3 0>;
+ };
+ gpio_rf_gpio_12:gpio_rf_gpio_12 {
+ gpios = <&gpio17 4 0>;
+ };
+ gpio_rf_gpio_13:gpio_rf_gpio_13 {
+ gpios = <&gpio17 5 0>;
+ };
+ gpio_rf_gpio_14:gpio_rf_gpio_14 {
+ gpios = <&gpio17 6 0>;
+ };
+ gpio_rf_gpio_15:gpio_rf_gpio_15 {
+ gpios = <&gpio17 7 0>;
+ };
+ gpio_rf_gpio_16:gpio_rf_gpio_16 {
+ gpios = <&gpio18 0 0>;
+ };
+ gpio_rf_gpio_17:gpio_rf_gpio_17 {
+ gpios = <&gpio18 1 0>;
+ };
+ gpio_rf_gpio_18:gpio_rf_gpio_18 {
+ gpios = <&gpio18 2 0>;
+ };
+ gpio_rf_gpio_19:gpio_rf_gpio_19 {
+ gpios = <&gpio18 3 0>;
+ };
+ gpio_rf_gpio_20:gpio_rf_gpio_20 {
+ gpios = <&gpio18 4 0>;
+ };
+ gpio_rf_gpio_21:gpio_rf_gpio_21 {
+ gpios = <&gpio18 5 0>;
+ };
+ gpio_rf_gpio_22:gpio_rf_gpio_22 {
+ gpios = <&gpio18 6 0>;
+ };
+ gpio_rf_gpio_23:gpio_rf_gpio_23 {
+ gpios = <&gpio18 7 0>;
+ };
+ gpio_rf_gpio_24:gpio_rf_gpio_24 {
+ gpios = <&gpio19 0 0>;
+ };
+ gpio_rf_gpio_25:gpio_rf_gpio_25 {
+ gpios = <&gpio19 1 0>;
+ };
+ gpio_rf_gpio_26:gpio_rf_gpio_26 {
+ gpios = <&gpio19 2 0>;
+ };
+ gpio_rf_ssi1:gpio_rf_ssi1 {
+ gpios = <&gpio19 3 0>;
+ };
+ gpio_rf_tcvr_on1:gpio_rf_tcvr_on1 {
+ gpios = <&gpio19 4 0>;
+ };
+ gpio_rf_gpio_29:gpio_rf_gpio_29 {
+ gpios = <&gpio19 5 0>;
+ };
+ gpio_rf_gpio_30:gpio_rf_gpio_30 {
+ gpios = <&gpio19 6 0>;
+ };
+ gpio_apt_pdm0:gpio_apt_pdm0 {
+ gpios = <&gpio19 7 0>;
+ };
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v2 05/16] arm64: dts: add Hi6220 pinctrl configuration nodes
2016-04-02 9:29 [PATCH v2 00/16] DTS for hi6220 and HiKey Guodong Xu
` (3 preceding siblings ...)
2016-04-02 9:29 ` [PATCH v2 04/16] arm64: dts: Add Hi6220 gpio configuration nodes Guodong Xu
@ 2016-04-02 9:29 ` Guodong Xu
2016-04-03 19:31 ` Linus Walleij
2016-04-02 9:29 ` [PATCH v2 06/16] arm64: dts: add Hi6220 spi " Guodong Xu
` (10 subsequent siblings)
15 siblings, 1 reply; 34+ messages in thread
From: Guodong Xu @ 2016-04-02 9:29 UTC (permalink / raw)
To: xuwei5, mark.rutland, robh, grant.likely, linus.walleij, arnd.bergmann
Cc: devicetree, linux-kernel, linux-arm-kernel, kong.kongxinwei,
Zhong Kaihua
From: Zhong Kaihua <zhongkaihua@huawei.com>
Add Hi6220 pinctrl configuration nodes
Signed-off-by: Zhong Kaihua <zhongkaihua@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts | 1 +
arch/arm64/boot/dts/hisilicon/hi6220.dtsi | 77 +++
arch/arm64/boot/dts/hisilicon/hikey-pinctrl.dtsi | 684 +++++++++++++++++++++++
include/dt-bindings/pinctrl/hisi.h | 59 ++
4 files changed, 821 insertions(+)
create mode 100644 arch/arm64/boot/dts/hisilicon/hikey-pinctrl.dtsi
create mode 100644 include/dt-bindings/pinctrl/hisi.h
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
index f9b2d1e..985a2ad 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
@@ -9,6 +9,7 @@
#include "hi6220.dtsi"
#include "hikey-gpio.dtsi"
+#include "hikey-pinctrl.dtsi"
/ {
model = "HiKey Development Board";
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
index ad7074d..e96cc3c 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
@@ -6,6 +6,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/hi6220-clock.h>
+#include <dt-bindings/pinctrl/hisi.h>
/ {
compatible = "hisilicon,hi6220";
@@ -250,6 +251,60 @@
clock-names = "apb_pclk";
};
+ pmx0: pinmux@f7010000 {
+ compatible = "pinctrl-single";
+ reg = <0x0 0xf7010000 0x0 0x27c>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ #gpio-range-cells = <3>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <7>;
+ pinctrl-single,gpio-range = <
+ &range 80 8 MUX_M0 /* gpio 3: [0..7] */
+ &range 88 8 MUX_M0 /* gpio 4: [0..7] */
+ &range 96 8 MUX_M0 /* gpio 5: [0..7] */
+ &range 104 8 MUX_M0 /* gpio 6: [0..7] */
+ &range 112 8 MUX_M0 /* gpio 7: [0..7] */
+ &range 120 2 MUX_M0 /* gpio 8: [0..1] */
+ &range 2 6 MUX_M1 /* gpio 8: [2..7] */
+ &range 8 8 MUX_M1 /* gpio 9: [0..7] */
+ &range 0 1 MUX_M1 /* gpio 10: [0] */
+ &range 16 7 MUX_M1 /* gpio 10: [1..7] */
+ &range 23 3 MUX_M1 /* gpio 11: [0..2] */
+ &range 28 5 MUX_M1 /* gpio 11: [3..7] */
+ &range 33 3 MUX_M1 /* gpio 12: [0..2] */
+ &range 43 5 MUX_M1 /* gpio 12: [3..7] */
+ &range 48 8 MUX_M1 /* gpio 13: [0..7] */
+ &range 56 8 MUX_M1 /* gpio 14: [0..7] */
+ &range 74 6 MUX_M1 /* gpio 15: [0..5] */
+ &range 122 1 MUX_M1 /* gpio 15: [6] */
+ &range 126 1 MUX_M1 /* gpio 15: [7] */
+ &range 127 8 MUX_M1 /* gpio 16: [0..7] */
+ &range 135 8 MUX_M1 /* gpio 17: [0..7] */
+ &range 143 8 MUX_M1 /* gpio 18: [0..7] */
+ &range 151 8 MUX_M1 /* gpio 19: [0..7] */
+ >;
+ range: gpio-range {
+ #pinctrl-single,gpio-range-cells = <3>;
+ };
+ };
+
+ pmx1: pinmux@f7010800 {
+ compatible = "pinconf-single";
+ reg = <0x0 0xf7010800 0x0 0x28c>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ pinctrl-single,register-width = <32>;
+ };
+
+ pmx2: pinmux@f8001800 {
+ compatible = "pinconf-single";
+ reg = <0x0 0xf8001800 0x0 0x78>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ pinctrl-single,register-width = <32>;
+ };
+
gpio0: gpio@f8011000 {
compatible = "arm,pl061", "arm,primecell";
reg = <0x0 0xf8011000 0x0 0x1000>;
@@ -295,6 +350,7 @@
interrupts = <0 55 0x4>;
gpio-controller;
#gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 80 8>;
interrupt-controller;
#interrupt-cells = <2>;
clocks = <&ao_ctrl 2>;
@@ -308,6 +364,7 @@
interrupts = <0 56 0x4>;
gpio-controller;
#gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 88 8>;
interrupt-controller;
#interrupt-cells = <2>;
clocks = <&ao_ctrl 2>;
@@ -321,6 +378,7 @@
interrupts = <0 57 0x4>;
gpio-controller;
#gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 96 8>;
interrupt-controller;
#interrupt-cells = <2>;
clocks = <&ao_ctrl 2>;
@@ -334,6 +392,7 @@
interrupts = <0 58 0x4>;
gpio-controller;
#gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 104 8>;
interrupt-controller;
#interrupt-cells = <2>;
clocks = <&ao_ctrl 2>;
@@ -347,6 +406,7 @@
interrupts = <0 59 0x4>;
gpio-controller;
#gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 112 8>;
interrupt-controller;
#interrupt-cells = <2>;
clocks = <&ao_ctrl 2>;
@@ -360,6 +420,7 @@
interrupts = <0 60 0x4>;
gpio-controller;
#gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 120 2 &pmx0 2 2 6>;
interrupt-controller;
#interrupt-cells = <2>;
clocks = <&ao_ctrl 2>;
@@ -373,6 +434,7 @@
interrupts = <0 61 0x4>;
gpio-controller;
#gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 8 8>;
interrupt-controller;
#interrupt-cells = <2>;
clocks = <&ao_ctrl 2>;
@@ -386,6 +448,7 @@
interrupts = <0 62 0x4>;
gpio-controller;
#gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 0 1 &pmx0 1 16 7>;
interrupt-controller;
#interrupt-cells = <2>;
clocks = <&ao_ctrl 2>;
@@ -399,6 +462,7 @@
interrupts = <0 63 0x4>;
gpio-controller;
#gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 23 3 &pmx0 3 28 5>;
interrupt-controller;
#interrupt-cells = <2>;
clocks = <&ao_ctrl 2>;
@@ -412,6 +476,7 @@
interrupts = <0 64 0x4>;
gpio-controller;
#gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 33 3 &pmx0 3 43 5>;
interrupt-controller;
#interrupt-cells = <2>;
clocks = <&ao_ctrl 2>;
@@ -424,6 +489,8 @@
reg = <0x0 0xf7029000 0x0 0x1000>;
interrupts = <0 65 0x4>;
gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 48 8>;
interrupt-controller;
#interrupt-cells = <2>;
clocks = <&ao_ctrl 2>;
@@ -437,6 +504,7 @@
interrupts = <0 66 0x4>;
gpio-controller;
#gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 56 8>;
interrupt-controller;
#interrupt-cells = <2>;
clocks = <&ao_ctrl 2>;
@@ -450,6 +518,11 @@
interrupts = <0 67 0x4>;
gpio-controller;
#gpio-cells = <2>;
+ gpio-ranges = <
+ &pmx0 0 74 6
+ &pmx0 6 122 1
+ &pmx0 7 126 1
+ >;
interrupt-controller;
#interrupt-cells = <2>;
clocks = <&ao_ctrl 2>;
@@ -463,6 +536,7 @@
interrupts = <0 68 0x4>;
gpio-controller;
#gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 127 8>;
interrupt-controller;
#interrupt-cells = <2>;
clocks = <&ao_ctrl 2>;
@@ -476,6 +550,7 @@
interrupts = <0 69 0x4>;
gpio-controller;
#gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 135 8>;
interrupt-controller;
#interrupt-cells = <2>;
clocks = <&ao_ctrl 2>;
@@ -489,6 +564,7 @@
interrupts = <0 70 0x4>;
gpio-controller;
#gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 143 8>;
interrupt-controller;
#interrupt-cells = <2>;
clocks = <&ao_ctrl 2>;
@@ -502,6 +578,7 @@
interrupts = <0 71 0x4>;
gpio-controller;
#gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 151 8>;
interrupt-controller;
#interrupt-cells = <2>;
clocks = <&ao_ctrl 2>;
diff --git a/arch/arm64/boot/dts/hisilicon/hikey-pinctrl.dtsi b/arch/arm64/boot/dts/hisilicon/hikey-pinctrl.dtsi
new file mode 100644
index 0000000..28806df
--- /dev/null
+++ b/arch/arm64/boot/dts/hisilicon/hikey-pinctrl.dtsi
@@ -0,0 +1,684 @@
+/*
+ * pinctrl dts fils for Hislicon HiKey development board
+ *
+ */
+#include <dt-bindings/pinctrl/hisi.h>
+
+/ {
+ soc {
+ pmx0: pinmux@f7010000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &boot_sel_pmx_func
+ &hkadc_ssi_pmx_func
+ &codec_clk_pmx_func
+ &pwm_in_pmx_func
+ &bl_pwm_pmx_func
+ >;
+
+ boot_sel_pmx_func: boot_sel_pmx_func {
+ pinctrl-single,pins = <
+ 0x0 MUX_M0 /* BOOT_SEL (IOMG000) */
+ >;
+ };
+
+ emmc_pmx_func: emmc_pmx_func {
+ pinctrl-single,pins = <
+ 0x100 MUX_M0 /* EMMC_CLK (IOMG064) */
+ 0x104 MUX_M0 /* EMMC_CMD (IOMG065) */
+ 0x108 MUX_M0 /* EMMC_DATA0 (IOMG066) */
+ 0x10c MUX_M0 /* EMMC_DATA1 (IOMG067) */
+ 0x110 MUX_M0 /* EMMC_DATA2 (IOMG068) */
+ 0x114 MUX_M0 /* EMMC_DATA3 (IOMG069) */
+ 0x118 MUX_M0 /* EMMC_DATA4 (IOMG070) */
+ 0x11c MUX_M0 /* EMMC_DATA5 (IOMG071) */
+ 0x120 MUX_M0 /* EMMC_DATA6 (IOMG072) */
+ 0x124 MUX_M0 /* EMMC_DATA7 (IOMG073) */
+ >;
+ };
+
+ sd_pmx_func: sd_pmx_func {
+ pinctrl-single,pins = <
+ 0xc MUX_M0 /* SD_CLK (IOMG003) */
+ 0x10 MUX_M0 /* SD_CMD (IOMG004) */
+ 0x14 MUX_M0 /* SD_DATA0 (IOMG005) */
+ 0x18 MUX_M0 /* SD_DATA1 (IOMG006) */
+ 0x1c MUX_M0 /* SD_DATA2 (IOMG007) */
+ 0x20 MUX_M0 /* SD_DATA3 (IOMG008) */
+ >;
+ };
+ sd_pmx_idle: sd_pmx_idle {
+ pinctrl-single,pins = <
+ 0xc MUX_M1 /* SD_CLK (IOMG003) */
+ 0x10 MUX_M1 /* SD_CMD (IOMG004) */
+ 0x14 MUX_M1 /* SD_DATA0 (IOMG005) */
+ 0x18 MUX_M1 /* SD_DATA1 (IOMG006) */
+ 0x1c MUX_M1 /* SD_DATA2 (IOMG007) */
+ 0x20 MUX_M1 /* SD_DATA3 (IOMG008) */
+ >;
+ };
+
+ sdio_pmx_func: sdio_pmx_func {
+ pinctrl-single,pins = <
+ 0x128 MUX_M0 /* SDIO_CLK (IOMG074) */
+ 0x12c MUX_M0 /* SDIO_CMD (IOMG075) */
+ 0x130 MUX_M0 /* SDIO_DATA0 (IOMG076) */
+ 0x134 MUX_M0 /* SDIO_DATA1 (IOMG077) */
+ 0x138 MUX_M0 /* SDIO_DATA2 (IOMG078) */
+ 0x13c MUX_M0 /* SDIO_DATA3 (IOMG079) */
+ >;
+ };
+ sdio_pmx_idle: sdio_pmx_idle {
+ pinctrl-single,pins = <
+ 0x128 MUX_M1 /* SDIO_CLK (IOMG074) */
+ 0x12c MUX_M1 /* SDIO_CMD (IOMG075) */
+ 0x130 MUX_M1 /* SDIO_DATA0 (IOMG076) */
+ 0x134 MUX_M1 /* SDIO_DATA1 (IOMG077) */
+ 0x138 MUX_M1 /* SDIO_DATA2 (IOMG078) */
+ 0x13c MUX_M1 /* SDIO_DATA3 (IOMG079) */
+ >;
+ };
+
+ isp_pmx_func: isp_pmx_func {
+ pinctrl-single,pins = <
+ 0x24 MUX_M0 /* ISP_PWDN0 (IOMG009) */
+ 0x28 MUX_M0 /* ISP_PWDN1 (IOMG010) */
+ 0x2c MUX_M0 /* ISP_PWDN2 (IOMG011) */
+ 0x30 MUX_M1 /* ISP_SHUTTER0 (IOMG012) */
+ 0x34 MUX_M1 /* ISP_SHUTTER1 (IOMG013) */
+ 0x38 MUX_M1 /* ISP_PWM (IOMG014) */
+ 0x3c MUX_M0 /* ISP_CCLK0 (IOMG015) */
+ 0x40 MUX_M0 /* ISP_CCLK1 (IOMG016) */
+ 0x44 MUX_M0 /* ISP_RESETB0 (IOMG017) */
+ 0x48 MUX_M0 /* ISP_RESETB1 (IOMG018) */
+ 0x4c MUX_M1 /* ISP_STROBE0 (IOMG019) */
+ 0x50 MUX_M1 /* ISP_STROBE1 (IOMG020) */
+ 0x54 MUX_M0 /* ISP_SDA0 (IOMG021) */
+ 0x58 MUX_M0 /* ISP_SCL0 (IOMG022) */
+ 0x5c MUX_M0 /* ISP_SDA1 (IOMG023) */
+ 0x60 MUX_M0 /* ISP_SCL1 (IOMG024) */
+ >;
+ };
+
+ hkadc_ssi_pmx_func: hkadc_ssi_pmx_func {
+ pinctrl-single,pins = <
+ 0x68 MUX_M0 /* HKADC_SSI (IOMG026) */
+ >;
+ };
+
+ codec_clk_pmx_func: codec_clk_pmx_func {
+ pinctrl-single,pins = <
+ 0x6c MUX_M0 /* CODEC_CLK (IOMG027) */
+ >;
+ };
+
+ codec_pmx_func: codec_pmx_func {
+ pinctrl-single,pins = <
+ 0x70 MUX_M1 /* DMIC_CLK (IOMG028) */
+ 0x74 MUX_M0 /* CODEC_SYNC (IOMG029) */
+ 0x78 MUX_M0 /* CODEC_DI (IOMG030) */
+ 0x7c MUX_M0 /* CODEC_DO (IOMG031) */
+ >;
+ };
+
+ fm_pmx_func: fm_pmx_func {
+ pinctrl-single,pins = <
+ 0x80 MUX_M1 /* FM_XCLK (IOMG032) */
+ 0x84 MUX_M1 /* FM_XFS (IOMG033) */
+ 0x88 MUX_M1 /* FM_DI (IOMG034) */
+ 0x8c MUX_M1 /* FM_DO (IOMG035) */
+ >;
+ };
+
+ bt_pmx_func: bt_pmx_func {
+ pinctrl-single,pins = <
+ 0x90 MUX_M0 /* BT_XCLK (IOMG036) */
+ 0x94 MUX_M0 /* BT_XFS (IOMG037) */
+ 0x98 MUX_M0 /* BT_DI (IOMG038) */
+ 0x9c MUX_M0 /* BT_DO (IOMG039) */
+ >;
+ };
+
+ pwm_in_pmx_func: pwm_in_pmx_func {
+ pinctrl-single,pins = <
+ 0xb8 MUX_M1 /* PWM_IN (IOMG046) */
+ >;
+ };
+
+ bl_pwm_pmx_func: bl_pwm_pmx_func {
+ pinctrl-single,pins = <
+ 0xbc MUX_M1 /* BL_PWM (IOMG047) */
+ >;
+ };
+
+ uart0_pmx_func: uart0_pmx_func {
+ pinctrl-single,pins = <
+ 0xc0 MUX_M0 /* UART0_RXD (IOMG048) */
+ 0xc4 MUX_M0 /* UART0_TXD (IOMG049) */
+ >;
+ };
+
+ uart1_pmx_func: uart1_pmx_func {
+ pinctrl-single,pins = <
+ 0xc8 MUX_M0 /* UART1_CTS_N (IOMG050) */
+ 0xcc MUX_M0 /* UART1_RTS_N (IOMG051) */
+ 0xd0 MUX_M0 /* UART1_RXD (IOMG052) */
+ 0xd4 MUX_M0 /* UART1_TXD (IOMG053) */
+ >;
+ };
+
+ uart2_pmx_func: uart2_pmx_func {
+ pinctrl-single,pins = <
+ 0xd8 MUX_M0 /* UART2_CTS_N (IOMG054) */
+ 0xdc MUX_M0 /* UART2_RTS_N (IOMG055) */
+ 0xe0 MUX_M0 /* UART2_RXD (IOMG056) */
+ 0xe4 MUX_M0 /* UART2_TXD (IOMG057) */
+ >;
+ };
+
+ uart3_pmx_func: uart3_pmx_func {
+ pinctrl-single,pins = <
+ 0x180 MUX_M1 /* UART3_CTS_N (IOMG096) */
+ 0x184 MUX_M1 /* UART3_RTS_N (IOMG097) */
+ 0x188 MUX_M1 /* UART3_RXD (IOMG098) */
+ 0x18c MUX_M1 /* UART3_TXD (IOMG099) */
+ >;
+ };
+
+ uart4_pmx_func: uart4_pmx_func {
+ pinctrl-single,pins = <
+ 0x1d0 MUX_M1 /* UART4_CTS_N (IOMG116) */
+ 0x1d4 MUX_M1 /* UART4_RTS_N (IOMG117) */
+ 0x1d8 MUX_M1 /* UART4_RXD (IOMG118) */
+ 0x1dc MUX_M1 /* UART4_TXD (IOMG119) */
+ >;
+ };
+
+ uart5_pmx_func: uart5_pmx_func {
+ pinctrl-single,pins = <
+ 0x1c8 MUX_M1 /* UART5_RXD (IOMG114) */
+ 0x1cc MUX_M1 /* UART5_TXD (IOMG115) */
+ >;
+ };
+
+ i2c0_pmx_func: i2c0_pmx_func {
+ pinctrl-single,pins = <
+ 0xe8 MUX_M0 /* I2C0_SCL (IOMG058) */
+ 0xec MUX_M0 /* I2C0_SDA (IOMG059) */
+ >;
+ };
+
+ i2c1_pmx_func: i2c1_pmx_func {
+ pinctrl-single,pins = <
+ 0xf0 MUX_M0 /* I2C1_SCL (IOMG060) */
+ 0xf4 MUX_M0 /* I2C1_SDA (IOMG061) */
+ >;
+ };
+
+ i2c2_pmx_func: i2c2_pmx_func {
+ pinctrl-single,pins = <
+ 0xf8 MUX_M0 /* I2C2_SCL (IOMG062) */
+ 0xfc MUX_M0 /* I2C2_SDA (IOMG063) */
+ >;
+ };
+ };
+
+ pmx1: pinmux@f7010800 {
+
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &boot_sel_cfg_func
+ &hkadc_ssi_cfg_func
+ &codec_clk_cfg_func
+ &pwm_in_cfg_func
+ &bl_pwm_cfg_func
+ >;
+
+ boot_sel_cfg_func: boot_sel_cfg_func {
+ pinctrl-single,pins = <
+ 0x0 0x0 /* BOOT_SEL (IOCFG000) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_UP PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ hkadc_ssi_cfg_func: hkadc_ssi_cfg_func {
+ pinctrl-single,pins = <
+ 0x6c 0x0 /* HKADC_SSI (IOCFG027) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ emmc_clk_cfg_func: emmc_clk_cfg_func {
+ pinctrl-single,pins = <
+ 0x104 0x0 /* EMMC_CLK (IOCFG065) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_08MA DRIVE_MASK>;
+ };
+
+ emmc_cfg_func: emmc_cfg_func {
+ pinctrl-single,pins = <
+ 0x108 0x0 /* EMMC_CMD (IOCFG066) */
+ 0x10c 0x0 /* EMMC_DATA0 (IOCFG067) */
+ 0x110 0x0 /* EMMC_DATA1 (IOCFG068) */
+ 0x114 0x0 /* EMMC_DATA2 (IOCFG069) */
+ 0x118 0x0 /* EMMC_DATA3 (IOCFG070) */
+ 0x11c 0x0 /* EMMC_DATA4 (IOCFG071) */
+ 0x120 0x0 /* EMMC_DATA5 (IOCFG072) */
+ 0x124 0x0 /* EMMC_DATA6 (IOCFG073) */
+ 0x128 0x0 /* EMMC_DATA7 (IOCFG074) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_UP PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_04MA DRIVE_MASK>;
+ };
+
+ emmc_rst_cfg_func: emmc_rst_cfg_func {
+ pinctrl-single,pins = <
+ 0x12c 0x0 /* EMMC_RST_N (IOCFG075) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_04MA DRIVE_MASK>;
+ };
+
+ sd_clk_cfg_func: sd_clk_cfg_func {
+ pinctrl-single,pins = <
+ 0xc 0x0 /* SD_CLK (IOCFG003) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_10MA DRIVE_MASK>;
+ };
+ sd_clk_cfg_idle: sd_clk_cfg_idle {
+ pinctrl-single,pins = <
+ 0xc 0x0 /* SD_CLK (IOCFG003) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DOWN PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ sd_cfg_func: sd_cfg_func {
+ pinctrl-single,pins = <
+ 0x10 0x0 /* SD_CMD (IOCFG004) */
+ 0x14 0x0 /* SD_DATA0 (IOCFG005) */
+ 0x18 0x0 /* SD_DATA1 (IOCFG006) */
+ 0x1c 0x0 /* SD_DATA2 (IOCFG007) */
+ 0x20 0x0 /* SD_DATA3 (IOCFG008) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_08MA DRIVE_MASK>;
+ };
+ sd_cfg_idle: sd_cfg_idle {
+ pinctrl-single,pins = <
+ 0x10 0x0 /* SD_CMD (IOCFG004) */
+ 0x14 0x0 /* SD_DATA0 (IOCFG005) */
+ 0x18 0x0 /* SD_DATA1 (IOCFG006) */
+ 0x1c 0x0 /* SD_DATA2 (IOCFG007) */
+ 0x20 0x0 /* SD_DATA3 (IOCFG008) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DOWN PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ sdio_clk_cfg_func: sdio_clk_cfg_func {
+ pinctrl-single,pins = <
+ 0x134 0x0 /* SDIO_CLK (IOCFG077) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_08MA DRIVE_MASK>;
+ };
+ sdio_clk_cfg_idle: sdio_clk_cfg_idle {
+ pinctrl-single,pins = <
+ 0x134 0x0 /* SDIO_CLK (IOCFG077) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DOWN PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ sdio_cfg_func: sdio_cfg_func {
+ pinctrl-single,pins = <
+ 0x138 0x0 /* SDIO_CMD (IOCFG078) */
+ 0x13c 0x0 /* SDIO_DATA0 (IOCFG079) */
+ 0x140 0x0 /* SDIO_DATA1 (IOCFG080) */
+ 0x144 0x0 /* SDIO_DATA2 (IOCFG081) */
+ 0x148 0x0 /* SDIO_DATA3 (IOCFG082) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_UP PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_04MA DRIVE_MASK>;
+ };
+ sdio_cfg_idle: sdio_cfg_idle {
+ pinctrl-single,pins = <
+ 0x138 0x0 /* SDIO_CMD (IOCFG078) */
+ 0x13c 0x0 /* SDIO_DATA0 (IOCFG079) */
+ 0x140 0x0 /* SDIO_DATA1 (IOCFG080) */
+ 0x144 0x0 /* SDIO_DATA2 (IOCFG081) */
+ 0x148 0x0 /* SDIO_DATA3 (IOCFG082) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_UP PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ isp_cfg_func1: isp_cfg_func1 {
+ pinctrl-single,pins = <
+ 0x28 0x0 /* ISP_PWDN0 (IOCFG010) */
+ 0x2c 0x0 /* ISP_PWDN1 (IOCFG011) */
+ 0x30 0x0 /* ISP_PWDN2 (IOCFG012) */
+ 0x34 0x0 /* ISP_SHUTTER0 (IOCFG013) */
+ 0x38 0x0 /* ISP_SHUTTER1 (IOCFG014) */
+ 0x3c 0x0 /* ISP_PWM (IOCFG015) */
+ 0x40 0x0 /* ISP_CCLK0 (IOCFG016) */
+ 0x44 0x0 /* ISP_CCLK1 (IOCFG017) */
+ 0x48 0x0 /* ISP_RESETB0 (IOCFG018) */
+ 0x4c 0x0 /* ISP_RESETB1 (IOCFG019) */
+ 0x50 0x0 /* ISP_STROBE0 (IOCFG020) */
+ 0x58 0x0 /* ISP_SDA0 (IOCFG022) */
+ 0x5c 0x0 /* ISP_SCL0 (IOCFG023) */
+ 0x60 0x0 /* ISP_SDA1 (IOCFG024) */
+ 0x64 0x0 /* ISP_SCL1 (IOCFG025) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+ isp_cfg_idle1: isp_cfg_idle1 {
+ pinctrl-single,pins = <
+ 0x34 0x0 /* ISP_SHUTTER0 (IOCFG013) */
+ 0x38 0x0 /* ISP_SHUTTER1 (IOCFG014) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DOWN PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ isp_cfg_func2: isp_cfg_func2 {
+ pinctrl-single,pins = <
+ 0x54 0x0 /* ISP_STROBE1 (IOCFG021) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DOWN PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ codec_clk_cfg_func: codec_clk_cfg_func {
+ pinctrl-single,pins = <
+ 0x70 0x0 /* CODEC_CLK (IOCFG028) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_04MA DRIVE_MASK>;
+ };
+ codec_clk_cfg_idle: codec_clk_cfg_idle {
+ pinctrl-single,pins = <
+ 0x70 0x0 /* CODEC_CLK (IOCFG028) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ codec_cfg_func1: codec_cfg_func1 {
+ pinctrl-single,pins = <
+ 0x74 0x0 /* DMIC_CLK (IOCFG029) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DOWN PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ codec_cfg_func2: codec_cfg_func2 {
+ pinctrl-single,pins = <
+ 0x78 0x0 /* CODEC_SYNC (IOCFG030) */
+ 0x7c 0x0 /* CODEC_DI (IOCFG031) */
+ 0x80 0x0 /* CODEC_DO (IOCFG032) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_04MA DRIVE_MASK>;
+ };
+ codec_cfg_idle2: codec_cfg_idle2 {
+ pinctrl-single,pins = <
+ 0x78 0x0 /* CODEC_SYNC (IOCFG030) */
+ 0x7c 0x0 /* CODEC_DI (IOCFG031) */
+ 0x80 0x0 /* CODEC_DO (IOCFG032) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ fm_cfg_func: fm_cfg_func {
+ pinctrl-single,pins = <
+ 0x84 0x0 /* FM_XCLK (IOCFG033) */
+ 0x88 0x0 /* FM_XFS (IOCFG034) */
+ 0x8c 0x0 /* FM_DI (IOCFG035) */
+ 0x90 0x0 /* FM_DO (IOCFG036) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DOWN PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ bt_cfg_func: bt_cfg_func {
+ pinctrl-single,pins = <
+ 0x94 0x0 /* BT_XCLK (IOCFG037) */
+ 0x98 0x0 /* BT_XFS (IOCFG038) */
+ 0x9c 0x0 /* BT_DI (IOCFG039) */
+ 0xa0 0x0 /* BT_DO (IOCFG040) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+ bt_cfg_idle: bt_cfg_idle {
+ pinctrl-single,pins = <
+ 0x94 0x0 /* BT_XCLK (IOCFG037) */
+ 0x98 0x0 /* BT_XFS (IOCFG038) */
+ 0x9c 0x0 /* BT_DI (IOCFG039) */
+ 0xa0 0x0 /* BT_DO (IOCFG040) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DOWN PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ pwm_in_cfg_func: pwm_in_cfg_func {
+ pinctrl-single,pins = <
+ 0xbc 0x0 /* PWM_IN (IOCFG047) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DOWN PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ bl_pwm_cfg_func: bl_pwm_cfg_func {
+ pinctrl-single,pins = <
+ 0xc0 0x0 /* BL_PWM (IOCFG048) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DOWN PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ uart0_cfg_func1: uart0_cfg_func1 {
+ pinctrl-single,pins = <
+ 0xc4 0x0 /* UART0_RXD (IOCFG049) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_UP PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ uart0_cfg_func2: uart0_cfg_func2 {
+ pinctrl-single,pins = <
+ 0xc8 0x0 /* UART0_TXD (IOCFG050) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_04MA DRIVE_MASK>;
+ };
+
+ uart1_cfg_func1: uart1_cfg_func1 {
+ pinctrl-single,pins = <
+ 0xcc 0x0 /* UART1_CTS_N (IOCFG051) */
+ 0xd4 0x0 /* UART1_RXD (IOCFG053) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_UP PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ uart1_cfg_func2: uart1_cfg_func2 {
+ pinctrl-single,pins = <
+ 0xd0 0x0 /* UART1_RTS_N (IOCFG052) */
+ 0xd8 0x0 /* UART1_TXD (IOCFG054) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ uart2_cfg_func: uart2_cfg_func {
+ pinctrl-single,pins = <
+ 0xdc 0x0 /* UART2_CTS_N (IOCFG055) */
+ 0xe0 0x0 /* UART2_RTS_N (IOCFG056) */
+ 0xe4 0x0 /* UART2_RXD (IOCFG057) */
+ 0xe8 0x0 /* UART2_TXD (IOCFG058) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ uart3_cfg_func: uart3_cfg_func {
+ pinctrl-single,pins = <
+ 0x190 0x0 /* UART3_CTS_N (IOCFG100) */
+ 0x194 0x0 /* UART3_RTS_N (IOCFG101) */
+ 0x198 0x0 /* UART3_RXD (IOCFG102) */
+ 0x19c 0x0 /* UART3_TXD (IOCFG103) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DOWN PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ uart4_cfg_func: uart4_cfg_func {
+ pinctrl-single,pins = <
+ 0x1e0 0x0 /* UART4_CTS_N (IOCFG120) */
+ 0x1e4 0x0 /* UART4_RTS_N (IOCFG121) */
+ 0x1e8 0x0 /* UART4_RXD (IOCFG122) */
+ 0x1ec 0x0 /* UART4_TXD (IOCFG123) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DOWN PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ uart5_cfg_func: uart5_cfg_func {
+ pinctrl-single,pins = <
+ 0x1d8 0x0 /* UART4_RXD (IOCFG118) */
+ 0x1dc 0x0 /* UART4_TXD (IOCFG119) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DOWN PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ i2c0_cfg_func: i2c0_cfg_func {
+ pinctrl-single,pins = <
+ 0xec 0x0 /* I2C0_SCL (IOCFG059) */
+ 0xf0 0x0 /* I2C0_SDA (IOCFG060) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ i2c1_cfg_func: i2c1_cfg_func {
+ pinctrl-single,pins = <
+ 0xf4 0x0 /* I2C1_SCL (IOCFG061) */
+ 0xf8 0x0 /* I2C1_SDA (IOCFG062) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ i2c2_cfg_func: i2c2_cfg_func {
+ pinctrl-single,pins = <
+ 0xfc 0x0 /* I2C2_SCL (IOCFG063) */
+ 0x100 0x0 /* I2C2_SDA (IOCFG064) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+ };
+
+ pmx2: pinmux@f8001800 {
+
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &rstout_n_cfg_func
+ >;
+
+ rstout_n_cfg_func: rstout_n_cfg_func {
+ pinctrl-single,pins = <
+ 0x0 0x0 /* RSTOUT_N (IOCFG000) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ pmu_peri_en_cfg_func: pmu_peri_en_cfg_func {
+ pinctrl-single,pins = <
+ 0x4 0x0 /* PMU_PERI_EN (IOCFG001) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ sysclk0_en_cfg_func: sysclk0_en_cfg_func {
+ pinctrl-single,pins = <
+ 0x8 0x0 /* SYSCLK0_EN (IOCFG002) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+
+ jtag_tdo_cfg_func: jtag_tdo_cfg_func {
+ pinctrl-single,pins = <
+ 0xc 0x0 /* JTAG_TDO (IOCFG003) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_08MA DRIVE_MASK>;
+ };
+
+ rf_reset_cfg_func: rf_reset_cfg_func {
+ pinctrl-single,pins = <
+ 0x70 0x0 /* RF_RESET0 (IOCFG028) */
+ 0x74 0x0 /* RF_RESET1 (IOCFG029) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
+ };
+ };
+};
diff --git a/include/dt-bindings/pinctrl/hisi.h b/include/dt-bindings/pinctrl/hisi.h
new file mode 100644
index 0000000..38f1ea8
--- /dev/null
+++ b/include/dt-bindings/pinctrl/hisi.h
@@ -0,0 +1,59 @@
+/*
+ * This header provides constants for hisilicon pinctrl bindings.
+ *
+ * Copyright (c) 2015 Hisilicon Limited.
+ * Copyright (c) 2015 Linaro Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _DT_BINDINGS_PINCTRL_HISI_H
+#define _DT_BINDINGS_PINCTRL_HISI_H
+
+/* iomg bit definition */
+#define MUX_M0 0
+#define MUX_M1 1
+#define MUX_M2 2
+#define MUX_M3 3
+#define MUX_M4 4
+#define MUX_M5 5
+#define MUX_M6 6
+#define MUX_M7 7
+
+/* iocg bit definition */
+#define PULL_MASK (3)
+#define PULL_DIS (0)
+#define PULL_UP (1 << 0)
+#define PULL_DOWN (1 << 1)
+
+/* drive strength definition */
+#define DRIVE_MASK (7 << 4)
+#define DRIVE1_02MA (0 << 4)
+#define DRIVE1_04MA (1 << 4)
+#define DRIVE1_08MA (2 << 4)
+#define DRIVE1_10MA (3 << 4)
+#define DRIVE2_02MA (0 << 4)
+#define DRIVE2_04MA (1 << 4)
+#define DRIVE2_08MA (2 << 4)
+#define DRIVE2_10MA (3 << 4)
+#define DRIVE3_04MA (0 << 4)
+#define DRIVE3_08MA (1 << 4)
+#define DRIVE3_12MA (2 << 4)
+#define DRIVE3_16MA (3 << 4)
+#define DRIVE3_20MA (4 << 4)
+#define DRIVE3_24MA (5 << 4)
+#define DRIVE3_32MA (6 << 4)
+#define DRIVE3_40MA (7 << 4)
+#define DRIVE4_02MA (0 << 4)
+#define DRIVE4_04MA (2 << 4)
+#define DRIVE4_08MA (4 << 4)
+#define DRIVE4_10MA (6 << 4)
+
+#endif
--
1.9.1
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v2 06/16] arm64: dts: add Hi6220 spi configuration nodes
2016-04-02 9:29 [PATCH v2 00/16] DTS for hi6220 and HiKey Guodong Xu
` (4 preceding siblings ...)
2016-04-02 9:29 ` [PATCH v2 05/16] arm64: dts: add Hi6220 pinctrl " Guodong Xu
@ 2016-04-02 9:29 ` Guodong Xu
2016-04-04 5:16 ` Rob Herring
2016-04-02 9:29 ` [PATCH v2 07/16] arm64: dts: add all hi6220 i2c nodes Guodong Xu
` (9 subsequent siblings)
15 siblings, 1 reply; 34+ messages in thread
From: Guodong Xu @ 2016-04-02 9:29 UTC (permalink / raw)
To: xuwei5, mark.rutland, robh, grant.likely, linus.walleij, arnd.bergmann
Cc: devicetree, linux-kernel, linux-arm-kernel, kong.kongxinwei,
Zhong Kaihua
From: Zhong Kaihua <zhongkaihua@huawei.com>
Add Hi6220 spi configuration nodes
Signed-off-by: Zhong Kaihua <zhongkaihua@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
---
arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts | 1 +
arch/arm64/boot/dts/hisilicon/hi6220.dtsi | 15 +++++++++++++++
arch/arm64/boot/dts/hisilicon/hikey-pinctrl.dtsi | 21 +++++++++++++++++++++
3 files changed, 37 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
index 985a2ad..5c9ee31 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
@@ -20,6 +20,7 @@
serial1 = &uart1; /* BT UART */
serial2 = &uart2; /* LS Expansion UART0 */
serial3 = &uart3; /* LS Expansion UART1 */
+ spi0 = &spi_0;
};
chosen {
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
index e96cc3c..dcca83b 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
@@ -585,5 +585,20 @@
clock-names = "apb_pclk";
status = "ok";
};
+
+ spi_0: spi@f7106000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0x0 0xf7106000 0x0 0x1000>;
+ interrupts = <0 50 4>;
+ bus-id = <0>;
+ enable-dma = <0>;
+ clocks = <&sys_ctrl HI6220_SPI_CLK>;
+ clock-names = "apb_pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pmx_func &spi0_cfg_func>;
+ num-cs = <1>;
+ cs-gpios = <&gpio6 2 0>;
+ status = "ok";
+ };
};
};
diff --git a/arch/arm64/boot/dts/hisilicon/hikey-pinctrl.dtsi b/arch/arm64/boot/dts/hisilicon/hikey-pinctrl.dtsi
index 28806df..0916e84 100644
--- a/arch/arm64/boot/dts/hisilicon/hikey-pinctrl.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hikey-pinctrl.dtsi
@@ -221,6 +221,15 @@
0xfc MUX_M0 /* I2C2_SDA (IOMG063) */
>;
};
+
+ spi0_pmx_func: spi0_pmx_func {
+ pinctrl-single,pins = <
+ 0x1a0 MUX_M1 /* SPI0_DI (IOMG104) */
+ 0x1a4 MUX_M1 /* SPI0_DO (IOMG105) */
+ 0x1a8 MUX_M1 /* SPI0_CS_N (IOMG106) */
+ 0x1ac MUX_M1 /* SPI0_CLK (IOMG107) */
+ >;
+ };
};
pmx1: pinmux@f7010800 {
@@ -625,6 +634,18 @@
pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
};
+
+ spi0_cfg_func: spi0_cfg_func {
+ pinctrl-single,pins = <
+ 0x1b0 0x0 /* SPI0_DI (IOCFG108) */
+ 0x1b4 0x0 /* SPI0_DO (IOCFG109) */
+ 0x1b8 0x0 /* SPI0_CS_N (IOCFG110) */
+ 0x1bc 0x0 /* SPI0_CLK (IOCFG111) */
+ >;
+ pinctrl-single,bias-pulldown = <PULL_DIS PULL_DOWN PULL_DIS PULL_DOWN>;
+ pinctrl-single,bias-pullup = <PULL_DIS PULL_UP PULL_DIS PULL_UP>;
+ pinctrl-single,drive-strength = <DRIVE1_02MA DRIVE_MASK>;
+ };
};
pmx2: pinmux@f8001800 {
--
1.9.1
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v2 07/16] arm64: dts: add all hi6220 i2c nodes
2016-04-02 9:29 [PATCH v2 00/16] DTS for hi6220 and HiKey Guodong Xu
` (5 preceding siblings ...)
2016-04-02 9:29 ` [PATCH v2 06/16] arm64: dts: add Hi6220 spi " Guodong Xu
@ 2016-04-02 9:29 ` Guodong Xu
2016-04-02 9:29 ` [PATCH v2 08/16] arm64: dts: hikey: enable i2c0 and i2c1 for working with mezzanine boards Guodong Xu
` (8 subsequent siblings)
15 siblings, 0 replies; 34+ messages in thread
From: Guodong Xu @ 2016-04-02 9:29 UTC (permalink / raw)
To: xuwei5, mark.rutland, robh, grant.likely, linus.walleij, arnd.bergmann
Cc: devicetree, linux-kernel, linux-arm-kernel, kong.kongxinwei, Chen Feng
From: Xinwei Kong <kong.kongxinwei@hisilicon.com>
This patch adds all I2C nodes for the Hi6220 SoC. This hi6220 Soc
use this I2C IP of Synopsys Designware for HiKey board.
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
---
arch/arm64/boot/dts/hisilicon/hi6220.dtsi | 33 +++++++++++++++++++++++++++++++
1 file changed, 33 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
index dcca83b..664cc7a 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
@@ -600,5 +600,38 @@
cs-gpios = <&gpio6 2 0>;
status = "ok";
};
+
+ i2c0: i2c@f7100000 {
+ compatible = "snps,designware-i2c";
+ reg = <0x0 0xf7100000 0x0 0x1000>;
+ interrupts = <0 44 4>;
+ clocks = <&sys_ctrl HI6220_I2C0_CLK>;
+ i2c-sda-hold-time-ns = <300>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pmx_func &i2c0_cfg_func>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@f7101000 {
+ compatible = "snps,designware-i2c";
+ reg = <0x0 0xf7101000 0x0 0x1000>;
+ clocks = <&sys_ctrl HI6220_I2C1_CLK>;
+ interrupts = <0 45 4>;
+ i2c-sda-hold-time-ns = <300>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pmx_func &i2c1_cfg_func>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@f7102000 {
+ compatible = "snps,designware-i2c";
+ reg = <0x0 0xf7102000 0x0 0x1000>;
+ clocks = <&sys_ctrl HI6220_I2C2_CLK>;
+ interrupts = <0 46 4>;
+ i2c-sda-hold-time-ns = <300>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pmx_func &i2c2_cfg_func>;
+ status = "disabled";
+ };
};
};
--
1.9.1
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v2 08/16] arm64: dts: hikey: enable i2c0 and i2c1 for working with mezzanine boards
2016-04-02 9:29 [PATCH v2 00/16] DTS for hi6220 and HiKey Guodong Xu
` (6 preceding siblings ...)
2016-04-02 9:29 ` [PATCH v2 07/16] arm64: dts: add all hi6220 i2c nodes Guodong Xu
@ 2016-04-02 9:29 ` Guodong Xu
2016-04-04 5:16 ` Rob Herring
2016-04-02 9:29 ` [PATCH v2 09/16] arm64: dts: add hi6220 usb node Guodong Xu
` (7 subsequent siblings)
15 siblings, 1 reply; 34+ messages in thread
From: Guodong Xu @ 2016-04-02 9:29 UTC (permalink / raw)
To: xuwei5, mark.rutland, robh, grant.likely, linus.walleij, arnd.bergmann
Cc: devicetree, linux-kernel, linux-arm-kernel, kong.kongxinwei, Guodong Xu
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
---
arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
index 5c9ee31..e00e9ec 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
@@ -42,6 +42,15 @@
<0x00000000 0x06e00000 0x00000000 0x0060f000>,
<0x00000000 0x07410000 0x00000000 0x36bf0000>;
};
+
+ soc {
+ i2c0: i2c@f7100000 {
+ status = "ok";
+ };
+ i2c1: i2c@f7101000 {
+ status = "ok";
+ };
+ };
};
&uart2 {
--
1.9.1
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v2 09/16] arm64: dts: add hi6220 usb node
2016-04-02 9:29 [PATCH v2 00/16] DTS for hi6220 and HiKey Guodong Xu
` (7 preceding siblings ...)
2016-04-02 9:29 ` [PATCH v2 08/16] arm64: dts: hikey: enable i2c0 and i2c1 for working with mezzanine boards Guodong Xu
@ 2016-04-02 9:29 ` Guodong Xu
2016-04-02 9:29 ` [PATCH v2 10/16] arm64: dts: add mailbox node for Hi6220 Guodong Xu
` (6 subsequent siblings)
15 siblings, 0 replies; 34+ messages in thread
From: Guodong Xu @ 2016-04-02 9:29 UTC (permalink / raw)
To: xuwei5, mark.rutland, robh, grant.likely, linus.walleij, arnd.bergmann
Cc: devicetree, linux-kernel, linux-arm-kernel, kong.kongxinwei,
Zhangfei Gao
From: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
---
arch/arm64/boot/dts/hisilicon/hi6220.dtsi | 32 +++++++++++++++++++++++++++++++
1 file changed, 32 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
index 664cc7a..2608b68 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
@@ -633,5 +633,37 @@
pinctrl-0 = <&i2c2_pmx_func &i2c2_cfg_func>;
status = "disabled";
};
+
+ fixed_5v_hub: regulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed_5v_hub";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ gpio = <&gpio0 7 0>;
+ regulator-always-on;
+ };
+
+ usb_phy: usbphy {
+ compatible = "hisilicon,hi6220-usb-phy";
+ #phy-cells = <0>;
+ phy-supply = <&fixed_5v_hub>;
+ hisilicon,peripheral-syscon = <&sys_ctrl>;
+ };
+
+ usb: usb@f72c0000 {
+ compatible = "hisilicon,hi6220-usb";
+ reg = <0x0 0xf72c0000 0x0 0x40000>;
+ phys = <&usb_phy>;
+ phy-names = "usb2-phy";
+ clocks = <&sys_ctrl HI6220_USBOTG_HCLK>;
+ clock-names = "otg";
+ dr_mode = "otg";
+ g-use-dma;
+ g-rx-fifo-size = <512>;
+ g-np-tx-fifo-size = <128>;
+ g-tx-fifo-size = <128 128 128 128 128 128>;
+ interrupts = <0 77 0x4>;
+ };
};
};
--
1.9.1
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v2 10/16] arm64: dts: add mailbox node for Hi6220
2016-04-02 9:29 [PATCH v2 00/16] DTS for hi6220 and HiKey Guodong Xu
` (8 preceding siblings ...)
2016-04-02 9:29 ` [PATCH v2 09/16] arm64: dts: add hi6220 usb node Guodong Xu
@ 2016-04-02 9:29 ` Guodong Xu
2016-04-02 9:29 ` [PATCH v2 11/16] arm64: dts: add Hi6220's stub clock node Guodong Xu
` (5 subsequent siblings)
15 siblings, 0 replies; 34+ messages in thread
From: Guodong Xu @ 2016-04-02 9:29 UTC (permalink / raw)
To: xuwei5, mark.rutland, robh, grant.likely, linus.walleij, arnd.bergmann
Cc: devicetree, linux-kernel, linux-arm-kernel, kong.kongxinwei, Leo Yan
From: Leo Yan <leo.yan@linaro.org>
This patch add device mailbox node for Hi6220 in DT.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
---
arch/arm64/boot/dts/hisilicon/hi6220.dtsi | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
index 2608b68..07b211b 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
@@ -665,5 +665,13 @@
g-tx-fifo-size = <128 128 128 128 128 128>;
interrupts = <0 77 0x4>;
};
+
+ mailbox: mailbox@f7510000 {
+ compatible = "hisilicon,hi6220-mbox";
+ reg = <0x0 0xf7510000 0x0 0x1000>, /* IPC_S */
+ <0x0 0x06dff800 0x0 0x0800>; /* Mailbox buffer */
+ interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <3>;
+ };
};
};
--
1.9.1
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v2 11/16] arm64: dts: add Hi6220's stub clock node
2016-04-02 9:29 [PATCH v2 00/16] DTS for hi6220 and HiKey Guodong Xu
` (9 preceding siblings ...)
2016-04-02 9:29 ` [PATCH v2 10/16] arm64: dts: add mailbox node for Hi6220 Guodong Xu
@ 2016-04-02 9:29 ` Guodong Xu
2016-04-02 9:29 ` [PATCH v2 12/16] arm64: dts: hi6220: add pinctrl for uarts and enable them Guodong Xu
` (4 subsequent siblings)
15 siblings, 0 replies; 34+ messages in thread
From: Guodong Xu @ 2016-04-02 9:29 UTC (permalink / raw)
To: xuwei5, mark.rutland, robh, grant.likely, linus.walleij, arnd.bergmann
Cc: devicetree, linux-kernel, linux-arm-kernel, kong.kongxinwei, Leo Yan
From: Leo Yan <leo.yan@linaro.org>
Enable SRAM node and stub clock node for Hi6220, which uses mailbox
channel 1 for CPU's frequency change.
Furthermore, add the CPU clock phandle in CPU's node and using
operating-points-v2 to register operating points. So can be used by
cpufreq-dt driver.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
---
arch/arm64/boot/dts/hisilicon/hi6220.dtsi | 56 +++++++++++++++++++++++++++++++
1 file changed, 56 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
index 07b211b..a7ca40b 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
@@ -82,6 +82,11 @@
device_type = "cpu";
reg = <0x0 0x0>;
enable-method = "psci";
+ clocks = <&stub_clock 0>;
+ operating-points-v2 = <&cpu_opp_table>;
+ cooling-min-level = <4>;
+ cooling-max-level = <0>;
+ #cooling-cells = <2>; /* min followed by max */
cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP>;
};
@@ -90,6 +95,7 @@
device_type = "cpu";
reg = <0x0 0x1>;
enable-method = "psci";
+ operating-points-v2 = <&cpu_opp_table>;
cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP>;
};
@@ -98,6 +104,7 @@
device_type = "cpu";
reg = <0x0 0x2>;
enable-method = "psci";
+ operating-points-v2 = <&cpu_opp_table>;
cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP>;
};
@@ -106,6 +113,7 @@
device_type = "cpu";
reg = <0x0 0x3>;
enable-method = "psci";
+ operating-points-v2 = <&cpu_opp_table>;
cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP>;
};
@@ -114,6 +122,7 @@
device_type = "cpu";
reg = <0x0 0x100>;
enable-method = "psci";
+ operating-points-v2 = <&cpu_opp_table>;
cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP>;
};
@@ -122,6 +131,7 @@
device_type = "cpu";
reg = <0x0 0x101>;
enable-method = "psci";
+ operating-points-v2 = <&cpu_opp_table>;
cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP>;
};
@@ -130,6 +140,7 @@
device_type = "cpu";
reg = <0x0 0x102>;
enable-method = "psci";
+ operating-points-v2 = <&cpu_opp_table>;
cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP>;
};
@@ -138,10 +149,42 @@
device_type = "cpu";
reg = <0x0 0x103>;
enable-method = "psci";
+ operating-points-v2 = <&cpu_opp_table>;
cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP>;
};
};
+ cpu_opp_table: cpu_opp_table {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp00 {
+ opp-hz = /bits/ 64 <208000000>;
+ opp-microvolt = <1040000>;
+ clock-latency-ns = <500000>;
+ };
+ opp01 {
+ opp-hz = /bits/ 64 <432000000>;
+ opp-microvolt = <1040000>;
+ clock-latency-ns = <500000>;
+ };
+ opp02 {
+ opp-hz = /bits/ 64 <729000000>;
+ opp-microvolt = <1090000>;
+ clock-latency-ns = <500000>;
+ };
+ opp03 {
+ opp-hz = /bits/ 64 <960000000>;
+ opp-microvolt = <1180000>;
+ clock-latency-ns = <500000>;
+ };
+ opp04 {
+ opp-hz = /bits/ 64 <1200000000>;
+ opp-microvolt = <1330000>;
+ clock-latency-ns = <500000>;
+ };
+ };
+
gic: interrupt-controller@f6801000 {
compatible = "arm,gic-400";
reg = <0x0 0xf6801000 0 0x1000>, /* GICD */
@@ -169,6 +212,11 @@
#size-cells = <2>;
ranges;
+ sram: sram@fff80000 {
+ compatible = "hisilicon,hi6220-sramctrl", "syscon";
+ reg = <0x0 0xfff80000 0x0 0x12000>;
+ };
+
ao_ctrl: ao_ctrl@f7800000 {
compatible = "hisilicon,hi6220-aoctrl", "syscon";
reg = <0x0 0xf7800000 0x0 0x2000>;
@@ -194,6 +242,14 @@
#clock-cells = <1>;
};
+ stub_clock: stub_clock {
+ compatible = "hisilicon,hi6220-stub-clk";
+ hisilicon,hi6220-clk-sram = <&sram>;
+ #clock-cells = <1>;
+ mbox-names = "mbox-tx";
+ mboxes = <&mailbox 1 0 11>;
+ };
+
uart0: uart@f8015000 { /* console */
compatible = "arm,pl011", "arm,primecell";
reg = <0x0 0xf8015000 0x0 0x1000>;
--
1.9.1
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v2 12/16] arm64: dts: hi6220: add pinctrl for uarts and enable them
2016-04-02 9:29 [PATCH v2 00/16] DTS for hi6220 and HiKey Guodong Xu
` (10 preceding siblings ...)
2016-04-02 9:29 ` [PATCH v2 11/16] arm64: dts: add Hi6220's stub clock node Guodong Xu
@ 2016-04-02 9:29 ` Guodong Xu
2016-04-02 9:29 ` [PATCH v2 13/16] arm64: dts: add LED nodes for hi6220-hikey Guodong Xu
` (3 subsequent siblings)
15 siblings, 0 replies; 34+ messages in thread
From: Guodong Xu @ 2016-04-02 9:29 UTC (permalink / raw)
To: xuwei5, mark.rutland, robh, grant.likely, linus.walleij, arnd.bergmann
Cc: devicetree, linux-kernel, linux-arm-kernel, kong.kongxinwei, Guodong Xu
Add pinctrl for uart2 uart3 and uart4. Enable uart1 uart2 and uart3.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
---
arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts | 12 ++++++++++++
arch/arm64/boot/dts/hisilicon/hi6220.dtsi | 9 +++++++++
2 files changed, 21 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
index e00e9ec..c4f560a 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
@@ -50,6 +50,18 @@
i2c1: i2c@f7101000 {
status = "ok";
};
+
+ uart1: uart@f7111000 {
+ status = "ok";
+ };
+
+ uart2: uart@f7112000 {
+ status = "ok";
+ };
+
+ uart3: uart@f7113000 {
+ status = "ok";
+ };
};
};
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
index a7ca40b..6afd327 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
@@ -266,6 +266,8 @@
clocks = <&sys_ctrl HI6220_UART1_PCLK>,
<&sys_ctrl HI6220_UART1_PCLK>;
clock-names = "uartclk", "apb_pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pmx_func &uart1_cfg_func1 &uart1_cfg_func2>;
status = "disabled";
};
@@ -276,6 +278,8 @@
clocks = <&sys_ctrl HI6220_UART2_PCLK>,
<&sys_ctrl HI6220_UART2_PCLK>;
clock-names = "uartclk", "apb_pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pmx_func &uart2_cfg_func>;
status = "disabled";
};
@@ -286,6 +290,9 @@
clocks = <&sys_ctrl HI6220_UART3_PCLK>,
<&sys_ctrl HI6220_UART3_PCLK>;
clock-names = "uartclk", "apb_pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pmx_func &uart3_cfg_func>;
+ status = "disabled";
};
uart4: uart@f7114000 {
@@ -295,6 +302,8 @@
clocks = <&sys_ctrl HI6220_UART4_PCLK>,
<&sys_ctrl HI6220_UART4_PCLK>;
clock-names = "uartclk", "apb_pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pmx_func &uart4_cfg_func>;
status = "disabled";
};
--
1.9.1
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v2 13/16] arm64: dts: add LED nodes for hi6220-hikey
2016-04-02 9:29 [PATCH v2 00/16] DTS for hi6220 and HiKey Guodong Xu
` (11 preceding siblings ...)
2016-04-02 9:29 ` [PATCH v2 12/16] arm64: dts: hi6220: add pinctrl for uarts and enable them Guodong Xu
@ 2016-04-02 9:29 ` Guodong Xu
2016-04-04 5:16 ` Rob Herring
2016-04-02 9:29 ` [PATCH v2 14/16] arm64: dts: hikey: Add hi655x pmic dts node Guodong Xu
` (2 subsequent siblings)
15 siblings, 1 reply; 34+ messages in thread
From: Guodong Xu @ 2016-04-02 9:29 UTC (permalink / raw)
To: xuwei5, mark.rutland, robh, grant.likely, linus.walleij, arnd.bergmann
Cc: devicetree, linux-kernel, linux-arm-kernel, kong.kongxinwei, Guodong Xu
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
---
arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts | 41 ++++++++++++++++++++++++++
1 file changed, 41 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
index c4f560a..28bc646 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
@@ -63,6 +63,47 @@
status = "ok";
};
};
+
+ leds {
+ compatible = "gpio-leds";
+ user_led4 {
+ label = "user_led4";
+ gpios = <&gpio4 0 0>; /* <&gpio_user_led_1>; */
+ linux,default-trigger = "heartbeat";
+ };
+
+ user_led3 {
+ label = "user_led3";
+ gpios = <&gpio4 1 0>; /* <&gpio_user_led_2>; */
+ linux,default-trigger = "mmc0";
+ };
+
+ user_led2 {
+ label = "user_led2";
+ gpios = <&gpio4 2 0>; /* <&gpio_user_led_3>; */
+ linux,default-trigger = "mmc1";
+ };
+
+ user_led1 {
+ label = "user_led1";
+ gpios = <&gpio4 3 0>; /* <&gpio_user_led_4>; */
+ linux,default-trigger = "cpu0";
+ };
+
+ wlan_active_led {
+ label = "wifi_active";
+ gpios = <&gpio3 5 0>; /* <&gpio_wlan_active_led>; */
+ linux,default-trigger = "phy0tx";
+ default-state = "off";
+ };
+
+ bt_active_led {
+ label = "bt_active";
+ gpios = <&gpio4 7 0>; /* <&gpio_bt_active_led>; */
+ linux,default-trigger = "hci0rx";
+ default-state = "off";
+ };
+ };
};
&uart2 {
--
1.9.1
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v2 14/16] arm64: dts: hikey: Add hi655x pmic dts node
2016-04-02 9:29 [PATCH v2 00/16] DTS for hi6220 and HiKey Guodong Xu
` (12 preceding siblings ...)
2016-04-02 9:29 ` [PATCH v2 13/16] arm64: dts: add LED nodes for hi6220-hikey Guodong Xu
@ 2016-04-02 9:29 ` Guodong Xu
2016-04-04 5:16 ` Rob Herring
2016-04-02 9:29 ` [PATCH v2 15/16] arm64: dts: add dwmmc nodes for hi6220 Guodong Xu
2016-04-02 9:29 ` [PATCH v2 16/16] arm64: dts: add wifi nodes support for hi6220-hikey Guodong Xu
15 siblings, 1 reply; 34+ messages in thread
From: Guodong Xu @ 2016-04-02 9:29 UTC (permalink / raw)
To: xuwei5, mark.rutland, robh, grant.likely, linus.walleij, arnd.bergmann
Cc: devicetree, linux-kernel, linux-arm-kernel, kong.kongxinwei,
Chen Feng, Fei Wang
From: Chen Feng <puck.chen@hisilicon.com>
Add the mfd hi655x dts node and regulator support on
hi6220 platform.
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Signed-off-by: Fei Wang <w.f@huawei.com>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Reviewed-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Guodong Xu <guodong.xu@linaro.org>
---
arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts | 87 ++++++++++++++++++++++++++
1 file changed, 87 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
index 28bc646..a6dffa8 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
@@ -6,6 +6,7 @@
*/
/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
#include "hi6220.dtsi"
#include "hikey-gpio.dtsi"
@@ -104,6 +105,92 @@
default-state = "off";
};
};
+
+ pmic: pmic@f8000000 {
+ compatible = "hisilicon,hi655x-pmic";
+ reg = <0x0 0xf8000000 0x0 0x1000>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ pmic-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ regulators {
+ ldo2: LDO2@a21 {
+ regulator-name = "LDO2_2V8";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3200000>;
+ regulator-enable-ramp-delay = <120>;
+ };
+
+ ldo7: LDO7@a26 {
+ regulator-name = "LDO7_SDIO";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-enable-ramp-delay = <120>;
+ };
+
+ ldo10: LDO10@a29 {
+ regulator-name = "LDO10_2V85";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-enable-ramp-delay = <360>;
+ };
+
+ ldo13: LDO13@a32 {
+ regulator-name = "LDO13_1V8";
+ regulator-min-microvolt = <1600000>;
+ regulator-max-microvolt = <1950000>;
+ regulator-enable-ramp-delay = <120>;
+ };
+
+ ldo14: LDO14@a33 {
+ regulator-name = "LDO14_2V8";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3200000>;
+ regulator-enable-ramp-delay = <120>;
+ };
+
+ ldo15: LDO15@a34 {
+ regulator-name = "LDO15_1V8";
+ regulator-min-microvolt = <1600000>;
+ regulator-max-microvolt = <1950000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-enable-ramp-delay = <120>;
+ };
+
+ ldo17: LDO17@a36 {
+ regulator-name = "LDO17_2V5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3200000>;
+ regulator-enable-ramp-delay = <120>;
+ };
+
+ ldo19: LDO19@a38 {
+ regulator-name = "LDO19_3V0";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-enable-ramp-delay = <360>;
+ };
+
+ ldo21: LDO21@a40 {
+ regulator-name = "LDO21_1V8";
+ regulator-min-microvolt = <1650000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-always-on;
+ regulator-enable-ramp-delay = <120>;
+ };
+
+ ldo22: LDO22@a41 {
+ regulator-name = "LDO22_1V2";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-enable-ramp-delay = <120>;
+ };
+ };
+ };
};
&uart2 {
--
1.9.1
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v2 15/16] arm64: dts: add dwmmc nodes for hi6220
2016-04-02 9:29 [PATCH v2 00/16] DTS for hi6220 and HiKey Guodong Xu
` (13 preceding siblings ...)
2016-04-02 9:29 ` [PATCH v2 14/16] arm64: dts: hikey: Add hi655x pmic dts node Guodong Xu
@ 2016-04-02 9:29 ` Guodong Xu
2016-04-02 9:29 ` [PATCH v2 16/16] arm64: dts: add wifi nodes support for hi6220-hikey Guodong Xu
15 siblings, 0 replies; 34+ messages in thread
From: Guodong Xu @ 2016-04-02 9:29 UTC (permalink / raw)
To: xuwei5, mark.rutland, robh, grant.likely, linus.walleij, arnd.bergmann
Cc: devicetree, linux-kernel, linux-arm-kernel, kong.kongxinwei, Guodong Xu
From: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Add all three dwmmc nodes description for hi6220
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
---
arch/arm64/boot/dts/hisilicon/hi6220.dtsi | 53 +++++++++++++++++++++++++++++++
1 file changed, 53 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
index 6afd327..28bd441 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
@@ -738,5 +738,58 @@
interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
#mbox-cells = <3>;
};
+
+ dwmmc_0: dwmmc0@f723d000 {
+ compatible = "hisilicon,hi6220-dw-mshc";
+ num-slots = <0x1>;
+ cap-mmc-highspeed;
+ non-removable;
+ reg = <0x0 0xf723d000 0x0 0x1000>;
+ interrupts = <0x0 0x48 0x4>;
+ clocks = <&sys_ctrl 2>, <&sys_ctrl 1>;
+ clock-names = "ciu", "biu";
+ bus-width = <0x8>;
+ vmmc-supply = <&ldo19>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_pmx_func &emmc_clk_cfg_func
+ &emmc_cfg_func &emmc_rst_cfg_func>;
+ };
+
+ dwmmc_1: dwmmc1@f723e000 {
+ compatible = "hisilicon,hi6220-dw-mshc";
+ num-slots = <0x1>;
+ card-detect-delay = <200>;
+ hisilicon,peripheral-syscon = <&ao_ctrl>;
+ cap-sd-highspeed;
+ reg = <0x0 0xf723e000 0x0 0x1000>;
+ interrupts = <0x0 0x49 0x4>;
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+ clocks = <&sys_ctrl 4>, <&sys_ctrl 3>;
+ clock-names = "ciu", "biu";
+ vqmmc-supply = <&ldo7>;
+ vmmc-supply = <&ldo10>;
+ bus-width = <0x4>;
+ disable-wp;
+ cd-gpios = <&gpio1 0 1>;
+ pinctrl-names = "default", "idle";
+ pinctrl-0 = <&sd_pmx_func &sd_clk_cfg_func &sd_cfg_func>;
+ pinctrl-1 = <&sd_pmx_idle &sd_clk_cfg_idle &sd_cfg_idle>;
+ };
+
+ dwmmc_2: dwmmc2@f723f000 {
+ compatible = "hisilicon,hi6220-dw-mshc";
+ status = "okay";
+ num-slots = <0x1>;
+ reg = <0x0 0xf723f000 0x0 0x1000>;
+ interrupts = <0x0 0x4a 0x4>;
+ clocks = <&sys_ctrl HI6220_MMC2_CIUCLK>, <&sys_ctrl HI6220_MMC2_CLK>;
+ clock-names = "ciu", "biu";
+ bus-width = <0x4>;
+ broken-cd;
+ pinctrl-names = "default", "idle";
+ pinctrl-0 = <&sdio_pmx_func &sdio_clk_cfg_func &sdio_cfg_func>;
+ pinctrl-1 = <&sdio_pmx_idle &sdio_clk_cfg_idle &sdio_cfg_idle>;
+ };
};
};
--
1.9.1
^ permalink raw reply related [flat|nested] 34+ messages in thread
* [PATCH v2 16/16] arm64: dts: add wifi nodes support for hi6220-hikey
2016-04-02 9:29 [PATCH v2 00/16] DTS for hi6220 and HiKey Guodong Xu
` (14 preceding siblings ...)
2016-04-02 9:29 ` [PATCH v2 15/16] arm64: dts: add dwmmc nodes for hi6220 Guodong Xu
@ 2016-04-02 9:29 ` Guodong Xu
15 siblings, 0 replies; 34+ messages in thread
From: Guodong Xu @ 2016-04-02 9:29 UTC (permalink / raw)
To: xuwei5, mark.rutland, robh, grant.likely, linus.walleij, arnd.bergmann
Cc: devicetree, linux-kernel, linux-arm-kernel, kong.kongxinwei, Guodong Xu
Add wifi nodes support for hi6220-hikey
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
---
arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts | 30 ++++++++++++++++++++++++++
1 file changed, 30 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
index a6dffa8..78ce994 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
@@ -48,6 +48,7 @@
i2c0: i2c@f7100000 {
status = "ok";
};
+
i2c1: i2c@f7101000 {
status = "ok";
};
@@ -63,6 +64,35 @@
uart3: uart@f7113000 {
status = "ok";
};
+
+ dwmmc_2: dwmmc2@f723f000 {
+ ti,non-removable;
+ non-removable;
+ /* WL_EN */
+ vmmc-supply = <&wlan_en_reg>;
+
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+ wlcore: wlcore@2 {
+ compatible = "ti,wl1835";
+ reg = <2>; /* sdio func num */
+ /* WL_IRQ, WL_HOST_WAKE_GPIO1_3 */
+ interrupt-parent = <&gpio1>;
+ interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+ };
+ };
+
+ wlan_en_reg: fixedregulator@1 {
+ compatible = "regulator-fixed";
+ regulator-name = "wlan-en-regulator";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ /* WLAN_EN GPIO */
+ gpio = <&gpio0 5 0>;
+ /* WLAN card specific delay */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
};
leds {
--
1.9.1
^ permalink raw reply related [flat|nested] 34+ messages in thread
* Re: [PATCH v2 02/16] arm64: dts: add sp804 timer node for Hi6220
2016-04-02 9:29 ` [PATCH v2 02/16] arm64: dts: add sp804 timer node for Hi6220 Guodong Xu
@ 2016-04-03 19:23 ` Linus Walleij
2016-04-04 1:43 ` Leo Yan
2016-04-04 5:16 ` Rob Herring
0 siblings, 2 replies; 34+ messages in thread
From: Linus Walleij @ 2016-04-03 19:23 UTC (permalink / raw)
To: Guodong Xu
Cc: Xu Wei, Mark Rutland, Rob Herring, Grant Likely, Arnd Bergmann,
devicetree, linux-kernel, linux-arm-kernel, XinWei Kong, Leo Yan
On Sat, Apr 2, 2016 at 11:29 AM, Guodong Xu <guodong.xu@linaro.org> wrote:
> From: Leo Yan <leo.yan@linaro.org>
>
> Add sp804 timer for hi6220, so it can be used as broadcast timer.
>
> Signed-off-by: Leo Yan <leo.yan@linaro.org>
> Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
> ---
> arch/arm64/boot/dts/hisilicon/hi6220.dtsi | 9 +++++++++
> 1 file changed, 9 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
> index ad1f1eb..82c4756 100644
> --- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
> +++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
> @@ -209,5 +209,14 @@
> clock-names = "uartclk", "apb_pclk";
> status = "disabled";
> };
> +
> + dual_timer0: dual_timer@f8008000 {
> + compatible = "arm,sp804", "arm,primecell";
> + reg = <0x0 0xf8008000 0x0 0x1000>;
> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ao_ctrl 27>;
> + clock-names = "apb_pclk";
How can this work? You only give the apb_pclk for clocking the
bus to the timer.
Most platforms using this driver has something like this:
timer01: timer@10104000 {
compatible = "arm,sp804", "arm,primecell";
reg = <0x10104000 0x1000>;
interrupt-parent = <&intc_dc1176>;
interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>, <0 9
IRQ_TYPE_LEVEL_HIGH>;
clocks = <&timclk>, <&timclk>, <&pclk>;
clock-names = "timer1", "timer2", "apb_pclk";
};
It then reads the two clocks in the beginning of clocks() to
determine the frequency of each timer.
By chance the code in the driver will allow just one clock and
will then assume that both the bus to the timer and the timer
itself is clocked from the same clock. But I highly doubt that this
is the case.
Please verify what clocks actually goes into this timer, it should
nominally be three of them.
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [PATCH v2 04/16] arm64: dts: Add Hi6220 gpio configuration nodes
2016-04-02 9:29 ` [PATCH v2 04/16] arm64: dts: Add Hi6220 gpio configuration nodes Guodong Xu
@ 2016-04-03 19:28 ` Linus Walleij
2016-04-12 9:18 ` Guodong Xu
0 siblings, 1 reply; 34+ messages in thread
From: Linus Walleij @ 2016-04-03 19:28 UTC (permalink / raw)
To: Guodong Xu
Cc: Xu Wei, Mark Rutland, Rob Herring, Grant Likely, Arnd Bergmann,
devicetree, linux-kernel, linux-arm-kernel, XinWei Kong,
Zhong Kaihua
On Sat, Apr 2, 2016 at 11:29 AM, Guodong Xu <guodong.xu@linaro.org> wrote:
> From: Zhong Kaihua <zhongkaihua@huawei.com>
>
> Add Hi6220 gpio configuration nodes
>
> Signed-off-by: Zhong Kaihua <zhongkaihua@huawei.com>
> Signed-off-by: Kong Xinwei <kong.kongxinwei@hisilicon.com>
>
Get rid of that blank line.
> Acked-by: Rob Herring <robh@kernel.org>
> Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
> +++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
> @@ -249,5 +249,264 @@
> clocks = <&ao_ctrl 27>;
> clock-names = "apb_pclk";
> };
> +
> + gpio0: gpio@f8011000 {
> + compatible = "arm,pl061", "arm,primecell";
> + reg = <0x0 0xf8011000 0x0 0x1000>;
> + interrupts = <0 52 0x4>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + clocks = <&ao_ctrl 2>;
> + clock-names = "apb_pclk";
> + status = "ok";
> + };
This part with all GPIO controllers looks nice.
> new file mode 100644
> index 0000000..09242f0
> --- /dev/null
> +++ b/arch/arm64/boot/dts/hisilicon/hikey-gpio.dtsi
> @@ -0,0 +1,607 @@
> +/ {
> + gpio_rstout_n:gpio_rstout_n {
> + gpios;
> + };
> + gpio_pmu_peri_en:gpio_pmu_peri_en {
> + gpios;
> + };
> + gpio_sysclk0_en:gpio_sysclk0_en {
> + gpios;
> + };
> + gpio_jtag_tdo:gpio_jtag_tdo {
> + gpios;
> + };
> + /* LCB: PWR_HOLD_GPIO0_0 */
> + gpio_pwr_hold:gpio_pwr_hold {
> + gpios = <&gpio0 0 0>;
> + };
(...)
I don't understand any stuff in this hikey-gpio.dtsi file.
What does all this mean?
If it has any practical use whatsoever then explain it in the
commit message, but right now it just looks like a big list
of placeholders with no use, but you can copy-paste them
into device nodes the day you need them?
If they are unused, just drop this file please.
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [PATCH v2 05/16] arm64: dts: add Hi6220 pinctrl configuration nodes
2016-04-02 9:29 ` [PATCH v2 05/16] arm64: dts: add Hi6220 pinctrl " Guodong Xu
@ 2016-04-03 19:31 ` Linus Walleij
2016-04-04 22:54 ` Tony Lindgren
0 siblings, 1 reply; 34+ messages in thread
From: Linus Walleij @ 2016-04-03 19:31 UTC (permalink / raw)
To: Guodong Xu, Haojian Zhuang, Tony Lindgren
Cc: Xu Wei, Mark Rutland, Rob Herring, Grant Likely, Arnd Bergmann,
devicetree, linux-kernel, linux-arm-kernel, XinWei Kong,
Zhong Kaihua
On Sat, Apr 2, 2016 at 11:29 AM, Guodong Xu <guodong.xu@linaro.org> wrote:
> From: Zhong Kaihua <zhongkaihua@huawei.com>
>
> Add Hi6220 pinctrl configuration nodes
>
> Signed-off-by: Zhong Kaihua <zhongkaihua@huawei.com>
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Nah. Acked-by is fine, but I didn't write handle or write this
code. :)
No ACK from Haojian? Tony? Looks allright?
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [PATCH v2 02/16] arm64: dts: add sp804 timer node for Hi6220
2016-04-03 19:23 ` Linus Walleij
@ 2016-04-04 1:43 ` Leo Yan
2016-04-04 11:21 ` Linus Walleij
2016-04-04 5:16 ` Rob Herring
1 sibling, 1 reply; 34+ messages in thread
From: Leo Yan @ 2016-04-04 1:43 UTC (permalink / raw)
To: Linus Walleij
Cc: Guodong Xu, Xu Wei, Mark Rutland, Rob Herring, Grant Likely,
Arnd Bergmann, devicetree, linux-kernel, linux-arm-kernel,
XinWei Kong
Hi Linus,
Thanks for review.
On Sun, Apr 03, 2016 at 09:23:42PM +0200, Linus Walleij wrote:
> On Sat, Apr 2, 2016 at 11:29 AM, Guodong Xu <guodong.xu@linaro.org> wrote:
>
> > From: Leo Yan <leo.yan@linaro.org>
> >
> > Add sp804 timer for hi6220, so it can be used as broadcast timer.
> >
> > Signed-off-by: Leo Yan <leo.yan@linaro.org>
> > Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
> > ---
> > arch/arm64/boot/dts/hisilicon/hi6220.dtsi | 9 +++++++++
> > 1 file changed, 9 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
> > index ad1f1eb..82c4756 100644
> > --- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
> > +++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
> > @@ -209,5 +209,14 @@
> > clock-names = "uartclk", "apb_pclk";
> > status = "disabled";
> > };
> > +
> > + dual_timer0: dual_timer@f8008000 {
> > + compatible = "arm,sp804", "arm,primecell";
> > + reg = <0x0 0xf8008000 0x0 0x1000>;
> > + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ao_ctrl 27>;
> > + clock-names = "apb_pclk";
>
> How can this work? You only give the apb_pclk for clocking the
> bus to the timer.
>
> Most platforms using this driver has something like this:
>
> timer01: timer@10104000 {
> compatible = "arm,sp804", "arm,primecell";
> reg = <0x10104000 0x1000>;
> interrupt-parent = <&intc_dc1176>;
> interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>, <0 9
> IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&timclk>, <&timclk>, <&pclk>;
> clock-names = "timer1", "timer2", "apb_pclk";
> };
>
> It then reads the two clocks in the beginning of clocks() to
> determine the frequency of each timer.
>
> By chance the code in the driver will allow just one clock and
> will then assume that both the bus to the timer and the timer
> itself is clocked from the same clock. But I highly doubt that this
> is the case.
This patch has been sent out for review previously [1]; So I refered
other platforms and changed to only enable apb bus clock due I have
not found timer enabling bits in Hi6220's spec.
> Please verify what clocks actually goes into this timer, it should
> nominally be three of them.
Yes, it can work well even I don't enable any timer clock. I will
check furthermore in spec to see if can bind with formal way as your
suggestion.
[1] http://archive.arm.linux.org.uk/lurker/message/20151009.131015.687ed525.en.html
Thanks,
Leo Yan
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [PATCH v2 02/16] arm64: dts: add sp804 timer node for Hi6220
2016-04-03 19:23 ` Linus Walleij
2016-04-04 1:43 ` Leo Yan
@ 2016-04-04 5:16 ` Rob Herring
1 sibling, 0 replies; 34+ messages in thread
From: Rob Herring @ 2016-04-04 5:16 UTC (permalink / raw)
To: Linus Walleij
Cc: Guodong Xu, Xu Wei, Mark Rutland, Grant Likely, Arnd Bergmann,
devicetree, linux-kernel, linux-arm-kernel, XinWei Kong, Leo Yan
On Sun, Apr 03, 2016 at 09:23:42PM +0200, Linus Walleij wrote:
> On Sat, Apr 2, 2016 at 11:29 AM, Guodong Xu <guodong.xu@linaro.org> wrote:
>
> > From: Leo Yan <leo.yan@linaro.org>
> >
> > Add sp804 timer for hi6220, so it can be used as broadcast timer.
> >
> > Signed-off-by: Leo Yan <leo.yan@linaro.org>
> > Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
> > ---
> > arch/arm64/boot/dts/hisilicon/hi6220.dtsi | 9 +++++++++
> > 1 file changed, 9 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
> > index ad1f1eb..82c4756 100644
> > --- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
> > +++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
> > @@ -209,5 +209,14 @@
> > clock-names = "uartclk", "apb_pclk";
> > status = "disabled";
> > };
> > +
> > + dual_timer0: dual_timer@f8008000 {
timer@...
> > + compatible = "arm,sp804", "arm,primecell";
> > + reg = <0x0 0xf8008000 0x0 0x1000>;
> > + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ao_ctrl 27>;
> > + clock-names = "apb_pclk";
>
> How can this work? You only give the apb_pclk for clocking the
> bus to the timer.
>
> Most platforms using this driver has something like this:
>
> timer01: timer@10104000 {
> compatible = "arm,sp804", "arm,primecell";
> reg = <0x10104000 0x1000>;
> interrupt-parent = <&intc_dc1176>;
> interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>, <0 9
> IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&timclk>, <&timclk>, <&pclk>;
> clock-names = "timer1", "timer2", "apb_pclk";
> };
>
> It then reads the two clocks in the beginning of clocks() to
> determine the frequency of each timer.
>
> By chance the code in the driver will allow just one clock and
> will then assume that both the bus to the timer and the timer
> itself is clocked from the same clock. But I highly doubt that this
> is the case.
I believe 1 clock was allowed for early bindings, but yes it should be
3.
Rob
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [PATCH v2 06/16] arm64: dts: add Hi6220 spi configuration nodes
2016-04-02 9:29 ` [PATCH v2 06/16] arm64: dts: add Hi6220 spi " Guodong Xu
@ 2016-04-04 5:16 ` Rob Herring
2016-04-12 9:40 ` Guodong Xu
0 siblings, 1 reply; 34+ messages in thread
From: Rob Herring @ 2016-04-04 5:16 UTC (permalink / raw)
To: Guodong Xu
Cc: xuwei5, mark.rutland, grant.likely, linus.walleij, arnd.bergmann,
devicetree, linux-kernel, linux-arm-kernel, kong.kongxinwei,
Zhong Kaihua
On Sat, Apr 02, 2016 at 05:29:33PM +0800, Guodong Xu wrote:
> From: Zhong Kaihua <zhongkaihua@huawei.com>
>
> Add Hi6220 spi configuration nodes
>
> Signed-off-by: Zhong Kaihua <zhongkaihua@huawei.com>
> Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
> ---
> arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts | 1 +
> arch/arm64/boot/dts/hisilicon/hi6220.dtsi | 15 +++++++++++++++
> arch/arm64/boot/dts/hisilicon/hikey-pinctrl.dtsi | 21 +++++++++++++++++++++
> 3 files changed, 37 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
> index 985a2ad..5c9ee31 100644
> --- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
> +++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
> @@ -20,6 +20,7 @@
> serial1 = &uart1; /* BT UART */
> serial2 = &uart2; /* LS Expansion UART0 */
> serial3 = &uart3; /* LS Expansion UART1 */
> + spi0 = &spi_0;
You shouldn't really need an alias for SPI.
> };
>
> chosen {
> diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
> index e96cc3c..dcca83b 100644
> --- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
> +++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
> @@ -585,5 +585,20 @@
> clock-names = "apb_pclk";
> status = "ok";
> };
> +
> + spi_0: spi@f7106000 {
> + compatible = "arm,pl022", "arm,primecell";
> + reg = <0x0 0xf7106000 0x0 0x1000>;
> + interrupts = <0 50 4>;
> + bus-id = <0>;
> + enable-dma = <0>;
> + clocks = <&sys_ctrl HI6220_SPI_CLK>;
> + clock-names = "apb_pclk";
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi0_pmx_func &spi0_cfg_func>;
> + num-cs = <1>;
> + cs-gpios = <&gpio6 2 0>;
> + status = "ok";
You only need an ok to override a disabled status, so I think you can
drop this. Or disable by default and let boards override it if that
makes sense.
Rob
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [PATCH v2 08/16] arm64: dts: hikey: enable i2c0 and i2c1 for working with mezzanine boards
2016-04-02 9:29 ` [PATCH v2 08/16] arm64: dts: hikey: enable i2c0 and i2c1 for working with mezzanine boards Guodong Xu
@ 2016-04-04 5:16 ` Rob Herring
0 siblings, 0 replies; 34+ messages in thread
From: Rob Herring @ 2016-04-04 5:16 UTC (permalink / raw)
To: Guodong Xu
Cc: xuwei5, mark.rutland, grant.likely, linus.walleij, arnd.bergmann,
devicetree, linux-kernel, linux-arm-kernel, kong.kongxinwei
On Sat, Apr 02, 2016 at 05:29:35PM +0800, Guodong Xu wrote:
> Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
> ---
> arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts | 9 +++++++++
> 1 file changed, 9 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
> index 5c9ee31..e00e9ec 100644
> --- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
> +++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
> @@ -42,6 +42,15 @@
> <0x00000000 0x06e00000 0x00000000 0x0060f000>,
> <0x00000000 0x07410000 0x00000000 0x36bf0000>;
> };
> +
> + soc {
> + i2c0: i2c@f7100000 {
> + status = "ok";
> + };
> + i2c1: i2c@f7101000 {
> + status = "ok";
> + };
Do these go to LS connector? If so, add 'label = "LS-I2C0";' or LS-I2C1
as appropriate (based on LS connector numbering).
Rob
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [PATCH v2 13/16] arm64: dts: add LED nodes for hi6220-hikey
2016-04-02 9:29 ` [PATCH v2 13/16] arm64: dts: add LED nodes for hi6220-hikey Guodong Xu
@ 2016-04-04 5:16 ` Rob Herring
0 siblings, 0 replies; 34+ messages in thread
From: Rob Herring @ 2016-04-04 5:16 UTC (permalink / raw)
To: Guodong Xu
Cc: xuwei5, mark.rutland, grant.likely, linus.walleij, arnd.bergmann,
devicetree, linux-kernel, linux-arm-kernel, kong.kongxinwei
On Sat, Apr 02, 2016 at 05:29:40PM +0800, Guodong Xu wrote:
> Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
> ---
> arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts | 41 ++++++++++++++++++++++++++
> 1 file changed, 41 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
> index c4f560a..28bc646 100644
> --- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
> +++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
> @@ -63,6 +63,47 @@
> status = "ok";
> };
> };
> +
> + leds {
> + compatible = "gpio-leds";
> + user_led4 {
Don't use underscores in node names: user-led4
> + label = "user_led4";
We need to make sure the node names and labels are aligned with other
boards. There's some discussion about this for the new db600 board.
This looks closer to what we should have than what we have for
db410c currently.
Rob
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [PATCH v2 14/16] arm64: dts: hikey: Add hi655x pmic dts node
2016-04-02 9:29 ` [PATCH v2 14/16] arm64: dts: hikey: Add hi655x pmic dts node Guodong Xu
@ 2016-04-04 5:16 ` Rob Herring
2016-04-12 13:14 ` Guodong Xu
0 siblings, 1 reply; 34+ messages in thread
From: Rob Herring @ 2016-04-04 5:16 UTC (permalink / raw)
To: Guodong Xu
Cc: xuwei5, mark.rutland, grant.likely, linus.walleij, arnd.bergmann,
devicetree, linux-kernel, linux-arm-kernel, kong.kongxinwei,
Chen Feng, Fei Wang
On Sat, Apr 02, 2016 at 05:29:41PM +0800, Guodong Xu wrote:
> From: Chen Feng <puck.chen@hisilicon.com>
>
> Add the mfd hi655x dts node and regulator support on
> hi6220 platform.
>
> Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
> Signed-off-by: Fei Wang <w.f@huawei.com>
> Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
> Reviewed-by: Haojian Zhuang <haojian.zhuang@linaro.org>
> Reviewed-by: Guodong Xu <guodong.xu@linaro.org>
> ---
> arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts | 87 ++++++++++++++++++++++++++
> 1 file changed, 87 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
> index 28bc646..a6dffa8 100644
> --- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
> +++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
> @@ -6,6 +6,7 @@
> */
>
> /dts-v1/;
> +#include <dt-bindings/gpio/gpio.h>
>
> #include "hi6220.dtsi"
> #include "hikey-gpio.dtsi"
> @@ -104,6 +105,92 @@
> default-state = "off";
> };
> };
> +
> + pmic: pmic@f8000000 {
> + compatible = "hisilicon,hi655x-pmic";
> + reg = <0x0 0xf8000000 0x0 0x1000>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + pmic-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
> + status = "okay";
> +
> + regulators {
> + ldo2: LDO2@a21 {
@a21 is not a unit address. Please drop these.
> + regulator-name = "LDO2_2V8";
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <3200000>;
> + regulator-enable-ramp-delay = <120>;
> + };
> +
> + ldo7: LDO7@a26 {
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [PATCH v2 02/16] arm64: dts: add sp804 timer node for Hi6220
2016-04-04 1:43 ` Leo Yan
@ 2016-04-04 11:21 ` Linus Walleij
2016-04-04 13:42 ` Leo Yan
0 siblings, 1 reply; 34+ messages in thread
From: Linus Walleij @ 2016-04-04 11:21 UTC (permalink / raw)
To: Leo Yan
Cc: Guodong Xu, Xu Wei, Mark Rutland, Rob Herring, Grant Likely,
Arnd Bergmann, devicetree, linux-kernel, linux-arm-kernel,
XinWei Kong
On Mon, Apr 4, 2016 at 3:43 AM, Leo Yan <leo.yan@linaro.org> wrote:
> On Sun, Apr 03, 2016 at 09:23:42PM +0200, Linus Walleij wrote:
>> On Sat, Apr 2, 2016 at 11:29 AM, Guodong Xu <guodong.xu@linaro.org> wrote:
>> By chance the code in the driver will allow just one clock and
>> will then assume that both the bus to the timer and the timer
>> itself is clocked from the same clock. But I highly doubt that this
>> is the case.
>
> This patch has been sent out for review previously [1]; So I refered
> other platforms and changed to only enable apb bus clock due I have
> not found timer enabling bits in Hi6220's spec.
This is not about enabling/disabling the clock(s) to the timer.
It doesn't matter if these clocks are always on.
It is about determining the *frequency* of the timers.
It is vital that the timer driver get the right frequency of the clock
to the block from the clock implementation, and I do not think
it is the same as the "apb_pclk".
The thing is that of course "any frequency" will
work but what you will notice is that the timer runs very
weirdly compared to wall-clock time unless the right clock
yielding the right frequency has been specified here.
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [PATCH v2 02/16] arm64: dts: add sp804 timer node for Hi6220
2016-04-04 11:21 ` Linus Walleij
@ 2016-04-04 13:42 ` Leo Yan
2016-04-04 13:53 ` Linus Walleij
0 siblings, 1 reply; 34+ messages in thread
From: Leo Yan @ 2016-04-04 13:42 UTC (permalink / raw)
To: Linus Walleij
Cc: Guodong Xu, Xu Wei, Mark Rutland, Rob Herring, Grant Likely,
Arnd Bergmann, devicetree, linux-kernel, linux-arm-kernel,
XinWei Kong
On Mon, Apr 04, 2016 at 01:21:00PM +0200, Linus Walleij wrote:
> On Mon, Apr 4, 2016 at 3:43 AM, Leo Yan <leo.yan@linaro.org> wrote:
> > On Sun, Apr 03, 2016 at 09:23:42PM +0200, Linus Walleij wrote:
> >> On Sat, Apr 2, 2016 at 11:29 AM, Guodong Xu <guodong.xu@linaro.org> wrote:
>
> >> By chance the code in the driver will allow just one clock and
> >> will then assume that both the bus to the timer and the timer
> >> itself is clocked from the same clock. But I highly doubt that this
> >> is the case.
> >
> > This patch has been sent out for review previously [1]; So I refered
> > other platforms and changed to only enable apb bus clock due I have
> > not found timer enabling bits in Hi6220's spec.
>
> This is not about enabling/disabling the clock(s) to the timer.
> It doesn't matter if these clocks are always on.
>
> It is about determining the *frequency* of the timers.
>
> It is vital that the timer driver get the right frequency of the clock
> to the block from the clock implementation, and I do not think
> it is the same as the "apb_pclk".
Thanks for reminding. Fortunately, apb_pclk and timer's clock are
same, all of them's rate are 19.2MHz.
> The thing is that of course "any frequency" will
> work but what you will notice is that the timer runs very
> weirdly compared to wall-clock time unless the right clock
> yielding the right frequency has been specified here.
Compared sp804 timer counter with wall-clock (which is using ARM's
arch timer), and confirmed that sp804 timer's counter register is
decreasing with rate 19.2MHz.
Also have checked Hi6220's spec, there have no timer's dediated clock
enabling bits. This is the reason before I only registered one clock.
So according to you and Rob's comments, how about change as below?
dual_timer0: timer@f8008000 {
compatible = "arm,sp804", "arm,primecell";
reg = <0x0 0xf8008000 0x0 0x1000>;
interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ao_ctrl HI6220_TIMER0_PCLK>,
<&ao_ctrl HI6220_TIMER0_PCLK>,
<&ao_ctrl HI6220_TIMER0_PCLK>;
clock-names = "apb_pclk", "apb_pclk", "apb_pclk";
};
Thanks,
Leo Yan
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [PATCH v2 02/16] arm64: dts: add sp804 timer node for Hi6220
2016-04-04 13:42 ` Leo Yan
@ 2016-04-04 13:53 ` Linus Walleij
2016-04-04 14:03 ` Leo Yan
0 siblings, 1 reply; 34+ messages in thread
From: Linus Walleij @ 2016-04-04 13:53 UTC (permalink / raw)
To: Leo Yan
Cc: Guodong Xu, Xu Wei, Mark Rutland, Rob Herring, Grant Likely,
Arnd Bergmann, devicetree, linux-kernel, linux-arm-kernel,
XinWei Kong
On Mon, Apr 4, 2016 at 3:42 PM, Leo Yan <leo.yan@linaro.org> wrote:
> On Mon, Apr 04, 2016 at 01:21:00PM +0200, Linus Walleij wrote:
>> This is not about enabling/disabling the clock(s) to the timer.
>> It doesn't matter if these clocks are always on.
>>
>> It is about determining the *frequency* of the timers.
>>
>> It is vital that the timer driver get the right frequency of the clock
>> to the block from the clock implementation, and I do not think
>> it is the same as the "apb_pclk".
>
> Thanks for reminding. Fortunately, apb_pclk and timer's clock are
> same, all of them's rate are 19.2MHz.
OK I was wrong, worrying about nothing.
>> The thing is that of course "any frequency" will
>> work but what you will notice is that the timer runs very
>> weirdly compared to wall-clock time unless the right clock
>> yielding the right frequency has been specified here.
>
> Compared sp804 timer counter with wall-clock (which is using ARM's
> arch timer), and confirmed that sp804 timer's counter register is
> decreasing with rate 19.2MHz.
Thanks, awesome.
> Also have checked Hi6220's spec, there have no timer's dediated clock
> enabling bits. This is the reason before I only registered one clock.
> So according to you and Rob's comments, how about change as below?
>
> dual_timer0: timer@f8008000 {
> compatible = "arm,sp804", "arm,primecell";
> reg = <0x0 0xf8008000 0x0 0x1000>;
> interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
> <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&ao_ctrl HI6220_TIMER0_PCLK>,
> <&ao_ctrl HI6220_TIMER0_PCLK>,
> <&ao_ctrl HI6220_TIMER0_PCLK>;
> clock-names = "apb_pclk", "apb_pclk", "apb_pclk";
This works for me, though I think only the last name
matters so I would name the first two "timer1" and "timer2".
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [PATCH v2 02/16] arm64: dts: add sp804 timer node for Hi6220
2016-04-04 13:53 ` Linus Walleij
@ 2016-04-04 14:03 ` Leo Yan
0 siblings, 0 replies; 34+ messages in thread
From: Leo Yan @ 2016-04-04 14:03 UTC (permalink / raw)
To: Linus Walleij
Cc: Guodong Xu, Xu Wei, Mark Rutland, Rob Herring, Grant Likely,
Arnd Bergmann, devicetree, linux-kernel, linux-arm-kernel,
XinWei Kong
On Mon, Apr 04, 2016 at 03:53:47PM +0200, Linus Walleij wrote:
> On Mon, Apr 4, 2016 at 3:42 PM, Leo Yan <leo.yan@linaro.org> wrote:
> > On Mon, Apr 04, 2016 at 01:21:00PM +0200, Linus Walleij wrote:
[...]
> > Also have checked Hi6220's spec, there have no timer's dediated clock
> > enabling bits. This is the reason before I only registered one clock.
> > So according to you and Rob's comments, how about change as below?
> >
> > dual_timer0: timer@f8008000 {
> > compatible = "arm,sp804", "arm,primecell";
> > reg = <0x0 0xf8008000 0x0 0x1000>;
> > interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
> > <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
> > clocks = <&ao_ctrl HI6220_TIMER0_PCLK>,
> > <&ao_ctrl HI6220_TIMER0_PCLK>,
> > <&ao_ctrl HI6220_TIMER0_PCLK>;
> > clock-names = "apb_pclk", "apb_pclk", "apb_pclk";
>
> This works for me, though I think only the last name
> matters so I would name the first two "timer1" and "timer2".
Will fix to "timer1" and "timer2" and sent out new patch.
Thanks,
Leo Yan
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [PATCH v2 05/16] arm64: dts: add Hi6220 pinctrl configuration nodes
2016-04-03 19:31 ` Linus Walleij
@ 2016-04-04 22:54 ` Tony Lindgren
0 siblings, 0 replies; 34+ messages in thread
From: Tony Lindgren @ 2016-04-04 22:54 UTC (permalink / raw)
To: Linus Walleij
Cc: Guodong Xu, Haojian Zhuang, Xu Wei, Mark Rutland, Rob Herring,
Grant Likely, Arnd Bergmann, devicetree, linux-kernel,
linux-arm-kernel, XinWei Kong, Zhong Kaihua
* Linus Walleij <linus.walleij@linaro.org> [160403 12:32]:
> On Sat, Apr 2, 2016 at 11:29 AM, Guodong Xu <guodong.xu@linaro.org> wrote:
>
> > From: Zhong Kaihua <zhongkaihua@huawei.com>
> >
> > Add Hi6220 pinctrl configuration nodes
> >
> > Signed-off-by: Zhong Kaihua <zhongkaihua@huawei.com>
> > Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
>
> Nah. Acked-by is fine, but I didn't write handle or write this
> code. :)
>
> No ACK from Haojian? Tony? Looks allright?
Looks OK to me, I guess no driver changes needed (again :)?
Tony
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [PATCH v2 04/16] arm64: dts: Add Hi6220 gpio configuration nodes
2016-04-03 19:28 ` Linus Walleij
@ 2016-04-12 9:18 ` Guodong Xu
0 siblings, 0 replies; 34+ messages in thread
From: Guodong Xu @ 2016-04-12 9:18 UTC (permalink / raw)
To: Linus Walleij
Cc: Xu Wei, Mark Rutland, Rob Herring, Grant Likely, Arnd Bergmann,
devicetree, linux-kernel, linux-arm-kernel, XinWei Kong,
Zhong Kaihua
On 4 April 2016 at 03:28, Linus Walleij <linus.walleij@linaro.org> wrote:
> On Sat, Apr 2, 2016 at 11:29 AM, Guodong Xu <guodong.xu@linaro.org> wrote:
>
>> From: Zhong Kaihua <zhongkaihua@huawei.com>
>>
>> Add Hi6220 gpio configuration nodes
>>
>> Signed-off-by: Zhong Kaihua <zhongkaihua@huawei.com>
>> Signed-off-by: Kong Xinwei <kong.kongxinwei@hisilicon.com>
>>
>
> Get rid of that blank line.
Will fix.
Sorry missed that in v3.
>
>> Acked-by: Rob Herring <robh@kernel.org>
>> Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
>
>> +++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
>> @@ -249,5 +249,264 @@
>> clocks = <&ao_ctrl 27>;
>> clock-names = "apb_pclk";
>> };
>> +
>> + gpio0: gpio@f8011000 {
>> + compatible = "arm,pl061", "arm,primecell";
>> + reg = <0x0 0xf8011000 0x0 0x1000>;
>> + interrupts = <0 52 0x4>;
>> + gpio-controller;
>> + #gpio-cells = <2>;
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> + clocks = <&ao_ctrl 2>;
>> + clock-names = "apb_pclk";
>> + status = "ok";
>> + };
>
> This part with all GPIO controllers looks nice.
>
>> new file mode 100644
>> index 0000000..09242f0
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/hisilicon/hikey-gpio.dtsi
>> @@ -0,0 +1,607 @@
>> +/ {
>> + gpio_rstout_n:gpio_rstout_n {
>> + gpios;
>> + };
>> + gpio_pmu_peri_en:gpio_pmu_peri_en {
>> + gpios;
>> + };
>> + gpio_sysclk0_en:gpio_sysclk0_en {
>> + gpios;
>> + };
>> + gpio_jtag_tdo:gpio_jtag_tdo {
>> + gpios;
>> + };
>> + /* LCB: PWR_HOLD_GPIO0_0 */
>> + gpio_pwr_hold:gpio_pwr_hold {
>> + gpios = <&gpio0 0 0>;
>> + };
>
> (...)
>
> I don't understand any stuff in this hikey-gpio.dtsi file.
>
> What does all this mean?
>
> If it has any practical use whatsoever then explain it in the
> commit message, but right now it just looks like a big list
> of placeholders with no use, but you can copy-paste them
> into device nodes the day you need them?
>
> If they are unused, just drop this file please.
I will drop this.
Sorry missed this in v2. I will fix this in next version.
-Guodong
>
> Yours,
> Linus Walleij
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [PATCH v2 06/16] arm64: dts: add Hi6220 spi configuration nodes
2016-04-04 5:16 ` Rob Herring
@ 2016-04-12 9:40 ` Guodong Xu
0 siblings, 0 replies; 34+ messages in thread
From: Guodong Xu @ 2016-04-12 9:40 UTC (permalink / raw)
To: Rob Herring
Cc: Xu Wei, Mark Rutland, Grant Likely, Linus Walleij, Arnd Bergmann,
devicetree, linux-kernel, linux-arm-kernel, XinWei Kong,
Zhong Kaihua
On 4 April 2016 at 13:16, Rob Herring <robh@kernel.org> wrote:
> On Sat, Apr 02, 2016 at 05:29:33PM +0800, Guodong Xu wrote:
>> From: Zhong Kaihua <zhongkaihua@huawei.com>
>>
>> Add Hi6220 spi configuration nodes
>>
>> Signed-off-by: Zhong Kaihua <zhongkaihua@huawei.com>
>> Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
>> ---
>> arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts | 1 +
>> arch/arm64/boot/dts/hisilicon/hi6220.dtsi | 15 +++++++++++++++
>> arch/arm64/boot/dts/hisilicon/hikey-pinctrl.dtsi | 21 +++++++++++++++++++++
>> 3 files changed, 37 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
>> index 985a2ad..5c9ee31 100644
>> --- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
>> +++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
>> @@ -20,6 +20,7 @@
>> serial1 = &uart1; /* BT UART */
>> serial2 = &uart2; /* LS Expansion UART0 */
>> serial3 = &uart3; /* LS Expansion UART1 */
>> + spi0 = &spi_0;
>
> You shouldn't really need an alias for SPI.
Will remove it.
>
>> };
>>
>> chosen {
>> diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
>> index e96cc3c..dcca83b 100644
>> --- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
>> +++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
>> @@ -585,5 +585,20 @@
>> clock-names = "apb_pclk";
>> status = "ok";
>> };
>> +
>> + spi_0: spi@f7106000 {
>> + compatible = "arm,pl022", "arm,primecell";
>> + reg = <0x0 0xf7106000 0x0 0x1000>;
>> + interrupts = <0 50 4>;
>> + bus-id = <0>;
>> + enable-dma = <0>;
>> + clocks = <&sys_ctrl HI6220_SPI_CLK>;
>> + clock-names = "apb_pclk";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&spi0_pmx_func &spi0_cfg_func>;
>> + num-cs = <1>;
>> + cs-gpios = <&gpio6 2 0>;
>> + status = "ok";
>
> You only need an ok to override a disabled status, so I think you can
> drop this. Or disable by default and let boards override it if that
> makes sense.
Thanks. I will modify this to "disabled", and enable it in board dts:
hi6220-hikey.dts
-Guodong
>
> Rob
^ permalink raw reply [flat|nested] 34+ messages in thread
* Re: [PATCH v2 14/16] arm64: dts: hikey: Add hi655x pmic dts node
2016-04-04 5:16 ` Rob Herring
@ 2016-04-12 13:14 ` Guodong Xu
0 siblings, 0 replies; 34+ messages in thread
From: Guodong Xu @ 2016-04-12 13:14 UTC (permalink / raw)
To: Rob Herring
Cc: Xu Wei, Mark Rutland, Grant Likely, Linus Walleij, Arnd Bergmann,
devicetree, linux-kernel, linux-arm-kernel, XinWei Kong,
Chen Feng, Fei Wang
On 4 April 2016 at 13:16, Rob Herring <robh@kernel.org> wrote:
> On Sat, Apr 02, 2016 at 05:29:41PM +0800, Guodong Xu wrote:
>> From: Chen Feng <puck.chen@hisilicon.com>
>>
>> Add the mfd hi655x dts node and regulator support on
>> hi6220 platform.
>>
>> Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
>> Signed-off-by: Fei Wang <w.f@huawei.com>
>> Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
>> Reviewed-by: Haojian Zhuang <haojian.zhuang@linaro.org>
>> Reviewed-by: Guodong Xu <guodong.xu@linaro.org>
>> ---
>> arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts | 87 ++++++++++++++++++++++++++
>> 1 file changed, 87 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
>> index 28bc646..a6dffa8 100644
>> --- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
>> +++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
>> @@ -6,6 +6,7 @@
>> */
>>
>> /dts-v1/;
>> +#include <dt-bindings/gpio/gpio.h>
>>
>> #include "hi6220.dtsi"
>> #include "hikey-gpio.dtsi"
>> @@ -104,6 +105,92 @@
>> default-state = "off";
>> };
>> };
>> +
>> + pmic: pmic@f8000000 {
>> + compatible = "hisilicon,hi655x-pmic";
>> + reg = <0x0 0xf8000000 0x0 0x1000>;
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> + pmic-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
>> + status = "okay";
>> +
>> + regulators {
>> + ldo2: LDO2@a21 {
>
> @a21 is not a unit address. Please drop these.
Will change these to
+ ldo2: LDO2 {
...
+ ldo7: LDO7 {
...
Thanks for review, Rob.
-Guodong
>
>> + regulator-name = "LDO2_2V8";
>> + regulator-min-microvolt = <2500000>;
>> + regulator-max-microvolt = <3200000>;
>> + regulator-enable-ramp-delay = <120>;
>> + };
>> +
>> + ldo7: LDO7@a26 {
^ permalink raw reply [flat|nested] 34+ messages in thread
end of thread, other threads:[~2016-04-12 13:14 UTC | newest]
Thread overview: 34+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-04-02 9:29 [PATCH v2 00/16] DTS for hi6220 and HiKey Guodong Xu
2016-04-02 9:29 ` [PATCH v2 01/16] arm64: dts: Reserve memory regions for hi6220 Guodong Xu
2016-04-02 9:29 ` [PATCH v2 02/16] arm64: dts: add sp804 timer node for Hi6220 Guodong Xu
2016-04-03 19:23 ` Linus Walleij
2016-04-04 1:43 ` Leo Yan
2016-04-04 11:21 ` Linus Walleij
2016-04-04 13:42 ` Leo Yan
2016-04-04 13:53 ` Linus Walleij
2016-04-04 14:03 ` Leo Yan
2016-04-04 5:16 ` Rob Herring
2016-04-02 9:29 ` [PATCH v2 03/16] arm64: dts: enable idle states " Guodong Xu
2016-04-02 9:29 ` [PATCH v2 04/16] arm64: dts: Add Hi6220 gpio configuration nodes Guodong Xu
2016-04-03 19:28 ` Linus Walleij
2016-04-12 9:18 ` Guodong Xu
2016-04-02 9:29 ` [PATCH v2 05/16] arm64: dts: add Hi6220 pinctrl " Guodong Xu
2016-04-03 19:31 ` Linus Walleij
2016-04-04 22:54 ` Tony Lindgren
2016-04-02 9:29 ` [PATCH v2 06/16] arm64: dts: add Hi6220 spi " Guodong Xu
2016-04-04 5:16 ` Rob Herring
2016-04-12 9:40 ` Guodong Xu
2016-04-02 9:29 ` [PATCH v2 07/16] arm64: dts: add all hi6220 i2c nodes Guodong Xu
2016-04-02 9:29 ` [PATCH v2 08/16] arm64: dts: hikey: enable i2c0 and i2c1 for working with mezzanine boards Guodong Xu
2016-04-04 5:16 ` Rob Herring
2016-04-02 9:29 ` [PATCH v2 09/16] arm64: dts: add hi6220 usb node Guodong Xu
2016-04-02 9:29 ` [PATCH v2 10/16] arm64: dts: add mailbox node for Hi6220 Guodong Xu
2016-04-02 9:29 ` [PATCH v2 11/16] arm64: dts: add Hi6220's stub clock node Guodong Xu
2016-04-02 9:29 ` [PATCH v2 12/16] arm64: dts: hi6220: add pinctrl for uarts and enable them Guodong Xu
2016-04-02 9:29 ` [PATCH v2 13/16] arm64: dts: add LED nodes for hi6220-hikey Guodong Xu
2016-04-04 5:16 ` Rob Herring
2016-04-02 9:29 ` [PATCH v2 14/16] arm64: dts: hikey: Add hi655x pmic dts node Guodong Xu
2016-04-04 5:16 ` Rob Herring
2016-04-12 13:14 ` Guodong Xu
2016-04-02 9:29 ` [PATCH v2 15/16] arm64: dts: add dwmmc nodes for hi6220 Guodong Xu
2016-04-02 9:29 ` [PATCH v2 16/16] arm64: dts: add wifi nodes support for hi6220-hikey Guodong Xu
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).