From: <shh.xie@gmail.com>
To: <devicetree@vger.kernel.org>, <robh+dt@kernel.org>,
<mark.rutland@arm.com>, <linux-arm-kernel@lists.infradead.org>,
<catalin.marinas@arm.com>, <will.deacon@arm.com>,
<shawnguo@kernel.org>, <linux-kernel@vger.kernel.org>
Cc: <arnd@arndb.de>, Shaohui Xie <Shaohui.Xie@nxp.com>
Subject: [PATCH 7/7] [v2] arm64: dts: add LS1046A-QDS board support
Date: Mon, 5 Sep 2016 18:01:35 +0800 [thread overview]
Message-ID: <1473069695-33092-8-git-send-email-shh.xie@gmail.com> (raw)
In-Reply-To: <1473069695-33092-1-git-send-email-shh.xie@gmail.com>
From: Shaohui Xie <Shaohui.Xie@nxp.com>
The LS1046A QorIQ development system (QDS) board is a high-performance
computing, evaluation, development, and test platform supporting the
LS1046A SoC.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
---
changes in V2:
1. updated aliases of serial nodes.
arch/arm64/boot/dts/freescale/Makefile | 1 +
arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts | 212 ++++++++++++++++++++++
2 files changed, 213 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 9c81b9e..6602718 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -1,5 +1,6 @@
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-rdb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts
new file mode 100644
index 0000000..290e5b0
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts
@@ -0,0 +1,212 @@
+/*
+ * Device Tree Include file for Freescale Layerscape-1046A family SoC.
+ *
+ * Copyright 2016, Freescale Semiconductor, Inc.
+ *
+ * Shaohui Xie <Shaohui.Xie@nxp.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "fsl-ls1046a.dtsi"
+
+/ {
+ model = "LS1046A QDS Board";
+ compatible = "fsl,ls1046a-qds", "fsl,ls1046a";
+
+ aliases {
+ gpio0 = &gpio0;
+ gpio1 = &gpio1;
+ gpio2 = &gpio2;
+ gpio3 = &gpio3;
+ serial0 = &duart0;
+ serial1 = &duart1;
+ serial2 = &duart2;
+ serial3 = &duart3;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&dspi {
+ bus-num = <0>;
+ status = "okay";
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "n25q128a11", "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+ };
+
+ flash@1 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "sst25wf040b", "jedec,spi-nor";
+ spi-cpol;
+ spi-cpha;
+ reg = <1>;
+ spi-max-frequency = <10000000>;
+ };
+
+ flash@2 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "en25s64", "jedec,spi-nor";
+ spi-cpol;
+ spi-cpha;
+ reg = <2>;
+ spi-max-frequency = <10000000>;
+ };
+};
+
+&duart0 {
+ status = "okay";
+};
+
+&duart1 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ pca9547@77 {
+ compatible = "nxp,pca9547";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x2>;
+
+ ina220@40 {
+ compatible = "ti,ina220";
+ reg = <0x40>;
+ shunt-resistor = <1000>;
+ };
+
+ ina220@41 {
+ compatible = "ti,ina220";
+ reg = <0x41>;
+ shunt-resistor = <1000>;
+ };
+ };
+
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x3>;
+
+ rtc@51 {
+ compatible = "nxp,pcf2129";
+ reg = <0x51>;
+ /* IRQ10_B */
+ interrupts = <0 150 0x4>;
+ };
+
+ eeprom@56 {
+ compatible = "atmel,24c512";
+ reg = <0x56>;
+ };
+
+ eeprom@57 {
+ compatible = "atmel,24c512";
+ reg = <0x57>;
+ };
+
+ temp-sensor@4c {
+ compatible = "adi,adt7461a";
+ reg = <0x4c>;
+ };
+ };
+ };
+};
+
+&ifc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ /* NOR, NAND Flashes and FPGA on board */
+ ranges = <0x0 0x0 0x0 0x60000000 0x08000000
+ 0x1 0x0 0x0 0x7e800000 0x00010000
+ 0x2 0x0 0x0 0x7fb00000 0x00000100>;
+ status = "okay";
+
+ nor@0,0 {
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x8000000>;
+ bank-width = <2>;
+ device-width = <1>;
+ };
+
+ nand@1,0 {
+ compatible = "fsl,ifc-nand";
+ reg = <0x1 0x0 0x10000>;
+ };
+
+ fpga: board-control@2,0 {
+ compatible = "fsl,ls1046aqds-fpga", "fsl,fpga-qixis";
+ reg = <0x2 0x0 0x0000100>;
+ };
+};
+
+&lpuart0 {
+ status = "okay";
+};
+
+&qspi {
+ num-cs = <2>;
+ bus-num = <0>;
+ status = "okay";
+
+ qflash0: s25fl128s@0 {
+ compatible = "spansion,m25p80";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ };
+};
--
2.1.0.27.g96db324
prev parent reply other threads:[~2016-09-05 10:49 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-09-05 10:01 [PATCH 0/7] [v2] arm64: dts: add QorIQ LS1046A SoC and boards support shh.xie
2016-09-05 10:01 ` [PATCH 1/7] [v2] dt-bindings: fsl: updates bindings for some SoC-specific devices shh.xie
2016-09-08 2:30 ` Shawn Guo
2016-09-08 10:57 ` S.H. Xie
2016-09-05 10:01 ` [PATCH 2/7] [v2] dt-bindings: i2c: adds two more nxp devices shh.xie
2016-09-12 16:33 ` Rob Herring
2016-09-05 10:01 ` [PATCH 3/7] [v2] arm64: dts: add QorIQ LS1046A SoC support shh.xie
2016-09-08 13:05 ` Shawn Guo
2016-09-09 6:46 ` S.H. Xie
2016-09-08 13:13 ` Mark Rutland
2016-09-08 13:18 ` Mark Rutland
2016-09-09 6:55 ` S.H. Xie
2016-09-09 9:10 ` Mark Rutland
2016-09-09 9:17 ` S.H. Xie
2016-09-09 6:48 ` S.H. Xie
2016-09-08 13:23 ` Marc Zyngier
2016-09-09 9:00 ` S.H. Xie
2016-09-05 10:01 ` [PATCH 4/7] [v2] Documentation: DT: Add entry for QorIQ LS1046A-RDB board shh.xie
2016-09-05 10:01 ` [PATCH 5/7] [v2] arm64: dts: add LS1046A-RDB board support shh.xie
2016-09-08 13:12 ` Shawn Guo
2016-09-09 6:44 ` S.H. Xie
2016-09-05 10:01 ` [PATCH 6/7] [v2] Documentation: DT: Add entry for QorIQ LS1046A-QDS board shh.xie
2016-09-05 10:01 ` shh.xie [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1473069695-33092-8-git-send-email-shh.xie@gmail.com \
--to=shh.xie@gmail.com \
--cc=Shaohui.Xie@nxp.com \
--cc=arnd@arndb.de \
--cc=catalin.marinas@arm.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
--cc=will.deacon@arm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).