linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* [PATCH v5 0/6] arm64: dts: NXP: add basic dts file for LX2160A SoC
@ 2018-10-14 17:07 Vabhav Sharma
  2018-10-14 17:07 ` [PATCH v5 1/6] dt-bindings: arm64: add compatible for LX2160A Vabhav Sharma
                   ` (5 more replies)
  0 siblings, 6 replies; 10+ messages in thread
From: Vabhav Sharma @ 2018-10-14 17:07 UTC (permalink / raw)
  To: sudeep.holla, oss, linux-kernel, devicetree, robh+dt,
	mark.rutland, linuxppc-dev, linux-arm-kernel, mturquette, sboyd,
	rjw, viresh.kumar, linux-clk, linux-pm, linux-kernel-owner,
	catalin.marinas, will.deacon, gregkh, arnd, kstewart,
	yamada.masahiro, leoyang.li, shawnguo
  Cc: linux, adrian.hunter, ulf.hansson, V.Sethi, udit.kumar,
	pankaj.bansal, Vabhav Sharma

Changes for v5:
- Updated temperature sensor regulator name in board device tree
- Sorted nodes alphabatically and unit-address in SoC/board device tree
- Identation, new line update in SoC/board device tree
- Updated nodes name as per DT spec generic name recommendation in SoC DT
- Updated macro define for interrupt/gpio property
- Updated i2c node property name scl-gpio
- Removed device_type property except cpu/memory node
- Added esdhc controller nodes in SoC/RDB board device tree
- Added aliases for uart/crypto nodes
- Add SoC die attribute definition for LX2160A

Changes for v4:
- Updated bindings for lx2160a clockgen and dcfg
- Modified commit message for lx2160a clockgen changes
- Updated interrupt property with macro definition
- Added required enable-method property to each core node with psci value
- Removed unused node syscon in device tree
- Removed blank lines in device tree fsl-lx2160a.dtsi
- Updated uart node compatible sbsa-uart first
- Added and defined vcc-supply property to temperature sensor node in
  device tree fsl-lx2160a-rdb.dts

Changes for v3:
-Split clockgen support patch into below two patches:
- a)Updated array size of cmux_to_group[] with NUM_CMUX+1 to include -1
 terminator and p4080 cmux_to_group[] array with -1 terminator
- b)Add clockgen support for lx2160a

Changes for v2:
- Modified cmux_to_group array to include -1 terminator
- Revert NUM_CMUX to original value 8 from 16
- Remove “As LX2160A is 16 core, so modified value for NUM_CMUX”
  in patch "[PATCH 3/5] drivers: clk-qoriq: Add clockgen support for
  lx2160a" description
- Populated cache properties for L1 and L2 cache in lx2160a device-tree.
- Removed reboot node from lx2160a device-tree as PSCI is implemented.
- Removed incorrect comment for timer node interrupt property in
  lx2160a device-tree.
- Modified pmu node compatible property from "arm,armv8-pmuv3" to
  "arm,cortex-a72-pmu" in lx2160a device-tree
- Non-standard aliases removed in lx2160a rdb board device-tree
- Updated i2c child nodes to generic name in lx2160a rdb device-tree.

Changes for v1:
- Add compatible string for LX2160A clockgen support
- Add compatible string to initialize LX2160A guts driver
- Add compatible string for LX2160A support in dt-bindings
- Add dts file to enable support for LX2160A SoC and LX2160A RDB
  (Reference design board)

Vabhav Sharma (4):
  dt-bindings: arm64: add compatible for LX2160A
  soc/fsl/guts: Add definition for LX2160A
  arm64: dts: add QorIQ LX2160A SoC support
  arm64: dts: add LX2160ARDB board support

Yogesh Gaur (2):
  clk: qoriq: increase array size of cmux_to_group
  clk: qoriq: Add clockgen support for lx2160a

 Documentation/devicetree/bindings/arm/fsl.txt      |  14 +-
 .../devicetree/bindings/clock/qoriq-clock.txt      |   1 +
 arch/arm64/boot/dts/freescale/Makefile             |   1 +
 arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts  | 119 ++++
 arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi     | 765 +++++++++++++++++++++
 drivers/clk/clk-qoriq.c                            |  16 +-
 drivers/cpufreq/qoriq-cpufreq.c                    |   1 +
 drivers/soc/fsl/guts.c                             |   6 +
 8 files changed, 920 insertions(+), 3 deletions(-)
 create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts
 create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi

-- 
2.7.4


^ permalink raw reply	[flat|nested] 10+ messages in thread

* [PATCH v5 1/6] dt-bindings: arm64: add compatible for LX2160A
  2018-10-14 17:07 [PATCH v5 0/6] arm64: dts: NXP: add basic dts file for LX2160A SoC Vabhav Sharma
@ 2018-10-14 17:07 ` Vabhav Sharma
  2018-10-14 17:07 ` [PATCH v5 2/6] soc/fsl/guts: Add definition " Vabhav Sharma
                   ` (4 subsequent siblings)
  5 siblings, 0 replies; 10+ messages in thread
From: Vabhav Sharma @ 2018-10-14 17:07 UTC (permalink / raw)
  To: sudeep.holla, oss, linux-kernel, devicetree, robh+dt,
	mark.rutland, linuxppc-dev, linux-arm-kernel, mturquette, sboyd,
	rjw, viresh.kumar, linux-clk, linux-pm, linux-kernel-owner,
	catalin.marinas, will.deacon, gregkh, arnd, kstewart,
	yamada.masahiro, leoyang.li, shawnguo
  Cc: linux, adrian.hunter, ulf.hansson, V.Sethi, udit.kumar,
	pankaj.bansal, Vabhav Sharma

Add compatible for LX2160A SoC,QDS and RDB board
Add lx2160a compatible for clockgen and dcfg

Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/arm/fsl.txt           | 14 +++++++++++++-
 Documentation/devicetree/bindings/clock/qoriq-clock.txt |  1 +
 2 files changed, 14 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt
index 8a1baa2..71adce2 100644
--- a/Documentation/devicetree/bindings/arm/fsl.txt
+++ b/Documentation/devicetree/bindings/arm/fsl.txt
@@ -130,7 +130,7 @@ core start address and release the secondary core from holdoff and startup.
   - compatible: Should contain a chip-specific compatible string,
 	Chip-specific strings are of the form "fsl,<chip>-dcfg",
 	The following <chip>s are known to be supported:
-	ls1012a, ls1021a, ls1043a, ls1046a, ls2080a.
+	ls1012a, ls1021a, ls1043a, ls1046a, ls2080a, lx2160a.
 
   - reg : should contain base address and length of DCFG memory-mapped registers
 
@@ -222,3 +222,15 @@ Required root node properties:
 LS2088A ARMv8 based RDB Board
 Required root node properties:
     - compatible = "fsl,ls2088a-rdb", "fsl,ls2088a";
+
+LX2160A SoC
+Required root node properties:
+    - compatible = "fsl,lx2160a";
+
+LX2160A ARMv8 based QDS Board
+Required root node properties:
+    - compatible = "fsl,lx2160a-qds", "fsl,lx2160a";
+
+LX2160A ARMv8 based RDB Board
+Required root node properties:
+    - compatible = "fsl,lx2160a-rdb", "fsl,lx2160a";
diff --git a/Documentation/devicetree/bindings/clock/qoriq-clock.txt b/Documentation/devicetree/bindings/clock/qoriq-clock.txt
index 97f46ad..3fb9995 100644
--- a/Documentation/devicetree/bindings/clock/qoriq-clock.txt
+++ b/Documentation/devicetree/bindings/clock/qoriq-clock.txt
@@ -37,6 +37,7 @@ Required properties:
 	* "fsl,ls1046a-clockgen"
 	* "fsl,ls1088a-clockgen"
 	* "fsl,ls2080a-clockgen"
+	* "fsl,lx2160a-clockgen"
 	Chassis-version clock strings include:
 	* "fsl,qoriq-clockgen-1.0": for chassis 1.0 clocks
 	* "fsl,qoriq-clockgen-2.0": for chassis 2.0 clocks
-- 
2.7.4


^ permalink raw reply	[flat|nested] 10+ messages in thread

* [PATCH v5 2/6] soc/fsl/guts: Add definition for LX2160A
  2018-10-14 17:07 [PATCH v5 0/6] arm64: dts: NXP: add basic dts file for LX2160A SoC Vabhav Sharma
  2018-10-14 17:07 ` [PATCH v5 1/6] dt-bindings: arm64: add compatible for LX2160A Vabhav Sharma
@ 2018-10-14 17:07 ` Vabhav Sharma
  2018-10-24 21:39   ` Li Yang
  2018-10-14 17:08 ` [PATCH v5 3/6] clk: qoriq: increase array size of cmux_to_group Vabhav Sharma
                   ` (3 subsequent siblings)
  5 siblings, 1 reply; 10+ messages in thread
From: Vabhav Sharma @ 2018-10-14 17:07 UTC (permalink / raw)
  To: sudeep.holla, oss, linux-kernel, devicetree, robh+dt,
	mark.rutland, linuxppc-dev, linux-arm-kernel, mturquette, sboyd,
	rjw, viresh.kumar, linux-clk, linux-pm, linux-kernel-owner,
	catalin.marinas, will.deacon, gregkh, arnd, kstewart,
	yamada.masahiro, leoyang.li, shawnguo
  Cc: linux, adrian.hunter, ulf.hansson, V.Sethi, udit.kumar,
	pankaj.bansal, Vabhav Sharma, Yinbo Zhu

Adding compatible string "lx2160a-dcfg" to
initialize guts driver for lx2160 and SoC die
attribute definition for LX2160A

Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
---
 drivers/soc/fsl/guts.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/soc/fsl/guts.c b/drivers/soc/fsl/guts.c
index 302e0c8..bcab1ee 100644
--- a/drivers/soc/fsl/guts.c
+++ b/drivers/soc/fsl/guts.c
@@ -100,6 +100,11 @@ static const struct fsl_soc_die_attr fsl_soc_die[] = {
 	  .svr		= 0x87000000,
 	  .mask		= 0xfff70000,
 	},
+	/* Die: LX2160A, SoC: LX2160A/LX2120A/LX2080A */
+	{ .die          = "LX2160A",
+	  .svr          = 0x87360000,
+	  .mask         = 0xff3f0000,
+	},
 	{ },
 };
 
@@ -222,6 +227,7 @@ static const struct of_device_id fsl_guts_of_match[] = {
 	{ .compatible = "fsl,ls1088a-dcfg", },
 	{ .compatible = "fsl,ls1012a-dcfg", },
 	{ .compatible = "fsl,ls1046a-dcfg", },
+	{ .compatible = "fsl,lx2160a-dcfg", },
 	{}
 };
 MODULE_DEVICE_TABLE(of, fsl_guts_of_match);
-- 
2.7.4


^ permalink raw reply	[flat|nested] 10+ messages in thread

* [PATCH v5 3/6] clk: qoriq: increase array size of cmux_to_group
  2018-10-14 17:07 [PATCH v5 0/6] arm64: dts: NXP: add basic dts file for LX2160A SoC Vabhav Sharma
  2018-10-14 17:07 ` [PATCH v5 1/6] dt-bindings: arm64: add compatible for LX2160A Vabhav Sharma
  2018-10-14 17:07 ` [PATCH v5 2/6] soc/fsl/guts: Add definition " Vabhav Sharma
@ 2018-10-14 17:08 ` Vabhav Sharma
  2018-10-16 22:44   ` Stephen Boyd
  2018-10-14 17:08 ` [PATCH v5 4/6] clk: qoriq: Add clockgen support for lx2160a Vabhav Sharma
                   ` (2 subsequent siblings)
  5 siblings, 1 reply; 10+ messages in thread
From: Vabhav Sharma @ 2018-10-14 17:08 UTC (permalink / raw)
  To: sudeep.holla, oss, linux-kernel, devicetree, robh+dt,
	mark.rutland, linuxppc-dev, linux-arm-kernel, mturquette, sboyd,
	rjw, viresh.kumar, linux-clk, linux-pm, linux-kernel-owner,
	catalin.marinas, will.deacon, gregkh, arnd, kstewart,
	yamada.masahiro, leoyang.li, shawnguo
  Cc: linux, adrian.hunter, ulf.hansson, V.Sethi, udit.kumar,
	pankaj.bansal, Yogesh Gaur, Vabhav Sharma

From: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>

Increase size of cmux_to_group array, to accomdate entry of
-1 termination.

Added -1, terminated, entry for 4080_cmux_grpX.

Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
---
 drivers/clk/clk-qoriq.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/clk/clk-qoriq.c b/drivers/clk/clk-qoriq.c
index 3a1812f..e152bfb 100644
--- a/drivers/clk/clk-qoriq.c
+++ b/drivers/clk/clk-qoriq.c
@@ -79,7 +79,7 @@ struct clockgen_chipinfo {
 	const struct clockgen_muxinfo *cmux_groups[2];
 	const struct clockgen_muxinfo *hwaccel[NUM_HWACCEL];
 	void (*init_periph)(struct clockgen *cg);
-	int cmux_to_group[NUM_CMUX]; /* -1 terminates if fewer than NUM_CMUX */
+	int cmux_to_group[NUM_CMUX+1]; /* array should be -1 terminated */
 	u32 pll_mask;	/* 1 << n bit set if PLL n is valid */
 	u32 flags;	/* CG_xxx */
 };
@@ -601,7 +601,7 @@ static const struct clockgen_chipinfo chipinfo[] = {
 			&p4080_cmux_grp1, &p4080_cmux_grp2
 		},
 		.cmux_to_group = {
-			0, 0, 0, 0, 1, 1, 1, 1
+			0, 0, 0, 0, 1, 1, 1, 1, -1
 		},
 		.pll_mask = 0x1f,
 	},
-- 
2.7.4


^ permalink raw reply	[flat|nested] 10+ messages in thread

* [PATCH v5 4/6] clk: qoriq: Add clockgen support for lx2160a
  2018-10-14 17:07 [PATCH v5 0/6] arm64: dts: NXP: add basic dts file for LX2160A SoC Vabhav Sharma
                   ` (2 preceding siblings ...)
  2018-10-14 17:08 ` [PATCH v5 3/6] clk: qoriq: increase array size of cmux_to_group Vabhav Sharma
@ 2018-10-14 17:08 ` Vabhav Sharma
  2018-10-14 17:08 ` [PATCH v5 5/6] arm64: dts: add QorIQ LX2160A SoC support Vabhav Sharma
  2018-10-14 17:08 ` [PATCH v5 6/6] arm64: dts: add LX2160ARDB board support Vabhav Sharma
  5 siblings, 0 replies; 10+ messages in thread
From: Vabhav Sharma @ 2018-10-14 17:08 UTC (permalink / raw)
  To: sudeep.holla, oss, linux-kernel, devicetree, robh+dt,
	mark.rutland, linuxppc-dev, linux-arm-kernel, mturquette, sboyd,
	rjw, viresh.kumar, linux-clk, linux-pm, linux-kernel-owner,
	catalin.marinas, will.deacon, gregkh, arnd, kstewart,
	yamada.masahiro, leoyang.li, shawnguo
  Cc: linux, adrian.hunter, ulf.hansson, V.Sethi, udit.kumar,
	pankaj.bansal, Yogesh Gaur, Tang Yuantian, Vabhav Sharma

From: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>

Add clockgen support for lx2160a.
Added entry for compat 'fsl,lx2160a-clockgen'.

Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
---
 drivers/clk/clk-qoriq.c         | 12 ++++++++++++
 drivers/cpufreq/qoriq-cpufreq.c |  1 +
 2 files changed, 13 insertions(+)

diff --git a/drivers/clk/clk-qoriq.c b/drivers/clk/clk-qoriq.c
index e152bfb..99675de 100644
--- a/drivers/clk/clk-qoriq.c
+++ b/drivers/clk/clk-qoriq.c
@@ -570,6 +570,17 @@ static const struct clockgen_chipinfo chipinfo[] = {
 		.flags = CG_VER3 | CG_LITTLE_ENDIAN,
 	},
 	{
+		.compat = "fsl,lx2160a-clockgen",
+		.cmux_groups = {
+			&clockgen2_cmux_cga12, &clockgen2_cmux_cgb
+		},
+		.cmux_to_group = {
+			0, 0, 0, 0, 1, 1, 1, 1, -1
+		},
+		.pll_mask = 0x37,
+		.flags = CG_VER3 | CG_LITTLE_ENDIAN,
+	},
+	{
 		.compat = "fsl,p2041-clockgen",
 		.guts_compat = "fsl,qoriq-device-config-1.0",
 		.init_periph = p2041_init_periph,
@@ -1424,6 +1435,7 @@ CLK_OF_DECLARE(qoriq_clockgen_ls1043a, "fsl,ls1043a-clockgen", clockgen_init);
 CLK_OF_DECLARE(qoriq_clockgen_ls1046a, "fsl,ls1046a-clockgen", clockgen_init);
 CLK_OF_DECLARE(qoriq_clockgen_ls1088a, "fsl,ls1088a-clockgen", clockgen_init);
 CLK_OF_DECLARE(qoriq_clockgen_ls2080a, "fsl,ls2080a-clockgen", clockgen_init);
+CLK_OF_DECLARE(qoriq_clockgen_lx2160a, "fsl,lx2160a-clockgen", clockgen_init);
 
 /* Legacy nodes */
 CLK_OF_DECLARE(qoriq_sysclk_1, "fsl,qoriq-sysclk-1.0", sysclk_init);
diff --git a/drivers/cpufreq/qoriq-cpufreq.c b/drivers/cpufreq/qoriq-cpufreq.c
index 3d773f6..83921b7 100644
--- a/drivers/cpufreq/qoriq-cpufreq.c
+++ b/drivers/cpufreq/qoriq-cpufreq.c
@@ -295,6 +295,7 @@ static const struct of_device_id node_matches[] __initconst = {
 	{ .compatible = "fsl,ls1046a-clockgen", },
 	{ .compatible = "fsl,ls1088a-clockgen", },
 	{ .compatible = "fsl,ls2080a-clockgen", },
+	{ .compatible = "fsl,lx2160a-clockgen", },
 	{ .compatible = "fsl,p4080-clockgen", },
 	{ .compatible = "fsl,qoriq-clockgen-1.0", },
 	{ .compatible = "fsl,qoriq-clockgen-2.0", },
-- 
2.7.4


^ permalink raw reply	[flat|nested] 10+ messages in thread

* [PATCH v5 5/6] arm64: dts: add QorIQ LX2160A SoC support
  2018-10-14 17:07 [PATCH v5 0/6] arm64: dts: NXP: add basic dts file for LX2160A SoC Vabhav Sharma
                   ` (3 preceding siblings ...)
  2018-10-14 17:08 ` [PATCH v5 4/6] clk: qoriq: Add clockgen support for lx2160a Vabhav Sharma
@ 2018-10-14 17:08 ` Vabhav Sharma
  2018-10-14 17:08 ` [PATCH v5 6/6] arm64: dts: add LX2160ARDB board support Vabhav Sharma
  5 siblings, 0 replies; 10+ messages in thread
From: Vabhav Sharma @ 2018-10-14 17:08 UTC (permalink / raw)
  To: sudeep.holla, oss, linux-kernel, devicetree, robh+dt,
	mark.rutland, linuxppc-dev, linux-arm-kernel, mturquette, sboyd,
	rjw, viresh.kumar, linux-clk, linux-pm, linux-kernel-owner,
	catalin.marinas, will.deacon, gregkh, arnd, kstewart,
	yamada.masahiro, leoyang.li, shawnguo
  Cc: linux, adrian.hunter, ulf.hansson, V.Sethi, udit.kumar,
	pankaj.bansal, Vabhav Sharma, Ramneek Mehresh, Zhang Ying-22455,
	Nipun Gupta, Priyanka Jain, Yogesh Gaur, Sriram Dash,
	Horia Geanta, Ran Wang, Yinbo Zhu

LX2160A SoC is based on Layerscape Chassis Generation 3.2 Architecture.

LX2160A features an advanced 16 64-bit ARM v8 CortexA72 processor cores
in 8 cluster, CCN508, GICv3,two 64-bit DDR4 memory controller, 8 I2C
controllers, 3 dspi, 2 esdhc,2 USB 3.0, mmu 500, 3 SATA, 4 PL011 SBSA
UARTs etc.

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@nxp.com>
Signed-off-by: Zhang Ying-22455 <ying.zhang22455@nxp.com>
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Horia Geanta <horia.geanta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
---
 arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi | 765 +++++++++++++++++++++++++
 1 file changed, 765 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi

diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
new file mode 100644
index 0000000..56f846c
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
@@ -0,0 +1,765 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Device Tree Include file for Layerscape-LX2160A family SoC.
+//
+// Copyright 2018 NXP
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/memreserve/ 0x80000000 0x00010000;
+
+/ {
+	compatible = "fsl,lx2160a";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		// 8 clusters having 2 Cortex-A72 cores each
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			enable-method = "psci";
+			reg = <0x0>;
+			clocks = <&clockgen 1 0>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <192>;
+			next-level-cache = <&cluster0_l2>;
+		};
+
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			enable-method = "psci";
+			reg = <0x1>;
+			clocks = <&clockgen 1 0>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <192>;
+			next-level-cache = <&cluster0_l2>;
+		};
+
+		cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			enable-method = "psci";
+			reg = <0x100>;
+			clocks = <&clockgen 1 1>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <192>;
+			next-level-cache = <&cluster1_l2>;
+		};
+
+		cpu@101 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			enable-method = "psci";
+			reg = <0x101>;
+			clocks = <&clockgen 1 1>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <192>;
+			next-level-cache = <&cluster1_l2>;
+		};
+
+		cpu@200 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			enable-method = "psci";
+			reg = <0x200>;
+			clocks = <&clockgen 1 2>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <192>;
+			next-level-cache = <&cluster2_l2>;
+		};
+
+		cpu@201 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			enable-method = "psci";
+			reg = <0x201>;
+			clocks = <&clockgen 1 2>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <192>;
+			next-level-cache = <&cluster2_l2>;
+		};
+
+		cpu@300 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			enable-method = "psci";
+			reg = <0x300>;
+			clocks = <&clockgen 1 3>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <192>;
+			next-level-cache = <&cluster3_l2>;
+		};
+
+		cpu@301 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			enable-method = "psci";
+			reg = <0x301>;
+			clocks = <&clockgen 1 3>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <192>;
+			next-level-cache = <&cluster3_l2>;
+		};
+
+		cpu@400 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			enable-method = "psci";
+			reg = <0x400>;
+			clocks = <&clockgen 1 4>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <192>;
+			next-level-cache = <&cluster4_l2>;
+		};
+
+		cpu@401 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			enable-method = "psci";
+			reg = <0x401>;
+			clocks = <&clockgen 1 4>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <192>;
+			next-level-cache = <&cluster4_l2>;
+		};
+
+		cpu@500 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			enable-method = "psci";
+			reg = <0x500>;
+			clocks = <&clockgen 1 5>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <192>;
+			next-level-cache = <&cluster5_l2>;
+		};
+
+		cpu@501 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			enable-method = "psci";
+			reg = <0x501>;
+			clocks = <&clockgen 1 5>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <192>;
+			next-level-cache = <&cluster5_l2>;
+		};
+
+		cpu@600 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			enable-method = "psci";
+			reg = <0x600>;
+			clocks = <&clockgen 1 6>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <192>;
+			next-level-cache = <&cluster6_l2>;
+		};
+
+		cpu@601 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			enable-method = "psci";
+			reg = <0x601>;
+			clocks = <&clockgen 1 6>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <192>;
+			next-level-cache = <&cluster6_l2>;
+		};
+
+		cpu@700 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			enable-method = "psci";
+			reg = <0x700>;
+			clocks = <&clockgen 1 7>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <192>;
+			next-level-cache = <&cluster7_l2>;
+		};
+
+		cpu@701 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			enable-method = "psci";
+			reg = <0x701>;
+			clocks = <&clockgen 1 7>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <192>;
+			next-level-cache = <&cluster7_l2>;
+		};
+
+		cluster0_l2: l2-cache0 {
+			compatible = "cache";
+			cache-size = <0x100000>;
+			cache-line-size = <64>;
+			cache-sets = <1024>;
+			cache-level = <2>;
+		};
+
+		cluster1_l2: l2-cache1 {
+			compatible = "cache";
+			cache-size = <0x100000>;
+			cache-line-size = <64>;
+			cache-sets = <1024>;
+			cache-level = <2>;
+		};
+
+		cluster2_l2: l2-cache2 {
+			compatible = "cache";
+			cache-size = <0x100000>;
+			cache-line-size = <64>;
+			cache-sets = <1024>;
+			cache-level = <2>;
+		};
+
+		cluster3_l2: l2-cache3 {
+			compatible = "cache";
+			cache-size = <0x100000>;
+			cache-line-size = <64>;
+			cache-sets = <1024>;
+			cache-level = <2>;
+		};
+
+		cluster4_l2: l2-cache4 {
+			compatible = "cache";
+			cache-size = <0x100000>;
+			cache-line-size = <64>;
+			cache-sets = <1024>;
+			cache-level = <2>;
+		};
+
+		cluster5_l2: l2-cache5 {
+			compatible = "cache";
+			cache-size = <0x100000>;
+			cache-line-size = <64>;
+			cache-sets = <1024>;
+			cache-level = <2>;
+		};
+
+		cluster6_l2: l2-cache6 {
+			compatible = "cache";
+			cache-size = <0x100000>;
+			cache-line-size = <64>;
+			cache-sets = <1024>;
+			cache-level = <2>;
+		};
+
+		cluster7_l2: l2-cache7 {
+			compatible = "cache";
+			cache-size = <0x100000>;
+			cache-line-size = <64>;
+			cache-sets = <1024>;
+			cache-level = <2>;
+		};
+	};
+
+	gic: interrupt-controller@6000000 {
+		compatible = "arm,gic-v3";
+		reg = <0x0 0x06000000 0 0x10000>, // GIC Dist
+			<0x0 0x06200000 0 0x200000>, // GICR (RD_base +
+						     // SGI_base)
+			<0x0 0x0c0c0000 0 0x2000>, // GICC
+			<0x0 0x0c0d0000 0 0x1000>, // GICH
+			<0x0 0x0c0e0000 0 0x20000>; // GICV
+		#interrupt-cells = <3>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		interrupt-controller;
+		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+
+		its: gic-its@6020000 {
+			compatible = "arm,gic-v3-its";
+			msi-controller;
+			reg = <0x0 0x6020000 0 0x20000>;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	pmu {
+		compatible = "arm,cortex-a72-pmu";
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	memory@80000000 {
+		// DRAM space - 1, size : 2 GB DRAM
+		device_type = "memory";
+		reg = <0x00000000 0x80000000 0 0x80000000>;
+	};
+
+	ddr1: memory-controller@1080000 {
+		compatible = "fsl,qoriq-memory-controller";
+		reg = <0x0 0x1080000 0x0 0x1000>;
+		interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+		little-endian;
+	};
+
+	ddr2: memory-controller@1090000 {
+		compatible = "fsl,qoriq-memory-controller";
+		reg = <0x0 0x1090000 0x0 0x1000>;
+		interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+		little-endian;
+	};
+
+	sysclk: sysclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+		clock-output-names = "sysclk";
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		crypto: crypto@8000000 {
+			compatible = "fsl,sec-v5.0", "fsl,sec-v4.0";
+			fsl,sec-era = <10>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x00 0x8000000 0x100000>;
+			reg = <0x00 0x8000000 0x0 0x100000>;
+			interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+			dma-coherent;
+			status = "disabled";
+
+			sec_jr0: jr@10000 {
+				compatible = "fsl,sec-v5.0-job-ring",
+					     "fsl,sec-v4.0-job-ring";
+				reg        = <0x10000 0x10000>;
+				interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			sec_jr1: jr@20000 {
+				compatible = "fsl,sec-v5.0-job-ring",
+					     "fsl,sec-v4.0-job-ring";
+				reg        = <0x20000 0x10000>;
+				interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			sec_jr2: jr@30000 {
+				compatible = "fsl,sec-v5.0-job-ring",
+					     "fsl,sec-v4.0-job-ring";
+				reg        = <0x30000 0x10000>;
+				interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			sec_jr3: jr@40000 {
+				compatible = "fsl,sec-v5.0-job-ring",
+					     "fsl,sec-v4.0-job-ring";
+				reg        = <0x40000 0x10000>;
+				interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
+		clockgen: clock-controller@1300000 {
+			compatible = "fsl,lx2160a-clockgen";
+			reg = <0 0x1300000 0 0xa0000>;
+			#clock-cells = <2>;
+			clocks = <&sysclk>;
+		};
+
+		dcfg: syscon@1e00000 {
+			compatible = "fsl,lx2160a-dcfg", "syscon";
+			reg = <0x0 0x1e00000 0x0 0x10000>;
+			little-endian;
+		};
+
+		i2c0: i2c@2000000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2000000 0x0 0x10000>;
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "i2c";
+			clocks = <&clockgen 4 7>;
+			scl-gpio = <&gpio2 15 GPIO_ACTIVE_HIGH>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@2010000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2010000 0x0 0x10000>;
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "i2c";
+			clocks = <&clockgen 4 7>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@2020000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2020000 0x0 0x10000>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "i2c";
+			clocks = <&clockgen 4 7>;
+			status = "disabled";
+		};
+
+		i2c3: i2c@2030000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2030000 0x0 0x10000>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "i2c";
+			clocks = <&clockgen 4 7>;
+			status = "disabled";
+		};
+
+		i2c4: i2c@2040000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2040000 0x0 0x10000>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "i2c";
+			clocks = <&clockgen 4 7>;
+			scl-gpio = <&gpio2 16 GPIO_ACTIVE_HIGH>;
+			status = "disabled";
+		};
+
+		i2c5: i2c@2050000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2050000 0x0 0x10000>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "i2c";
+			clocks = <&clockgen 4 7>;
+			status = "disabled";
+		};
+
+		i2c6: i2c@2060000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2060000 0x0 0x10000>;
+			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "i2c";
+			clocks = <&clockgen 4 7>;
+			status = "disabled";
+		};
+
+		i2c7: i2c@2070000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2070000 0x0 0x10000>;
+			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "i2c";
+			clocks = <&clockgen 4 7>;
+			status = "disabled";
+		};
+
+		esdhc0: esdhc@2140000 {
+			compatible = "fsl,esdhc";
+			reg = <0x0 0x2140000 0x0 0x10000>;
+			interrupts = <0 28 0x4>; /* Level high type */
+			clocks = <&clockgen 4 1>;
+			voltage-ranges = <1800 1800 3300 3300>;
+			sdhci,auto-cmd12;
+			little-endian;
+			bus-width = <4>;
+			status = "disabled";
+		};
+
+		esdhc1: esdhc@2150000 {
+			compatible = "fsl,esdhc";
+			reg = <0x0 0x2150000 0x0 0x10000>;
+			interrupts = <0 63 0x4>; /* Level high type */
+			clocks = <&clockgen 4 1>;
+			voltage-ranges = <1800 1800 3300 3300>;
+			sdhci,auto-cmd12;
+			broken-cd;
+			little-endian;
+			bus-width = <4>;
+			status = "disabled";
+		};
+
+		uart0: serial@21c0000 {
+			compatible = "arm,sbsa-uart","arm,pl011";
+			reg = <0x0 0x21c0000 0x0 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			current-speed = <115200>;
+			status = "disabled";
+		};
+
+		uart1: serial@21d0000 {
+			compatible = "arm,sbsa-uart","arm,pl011";
+			reg = <0x0 0x21d0000 0x0 0x1000>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			current-speed = <115200>;
+			status = "disabled";
+		};
+
+		uart2: serial@21e0000 {
+			compatible = "arm,sbsa-uart","arm,pl011";
+			reg = <0x0 0x21e0000 0x0 0x1000>;
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+			current-speed = <115200>;
+			status = "disabled";
+		};
+
+		uart3: serial@21f0000 {
+			compatible = "arm,sbsa-uart","arm,pl011";
+			reg = <0x0 0x21f0000 0x0 0x1000>;
+			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+			current-speed = <115200>;
+			status = "disabled";
+		};
+
+		gpio0: gpio@2300000 {
+			compatible = "fsl,qoriq-gpio";
+			reg = <0x0 0x2300000 0x0 0x10000>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			little-endian;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio1: gpio@2310000 {
+			compatible = "fsl,qoriq-gpio";
+			reg = <0x0 0x2310000 0x0 0x10000>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			little-endian;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio2: gpio@2320000 {
+			compatible = "fsl,qoriq-gpio";
+			reg = <0x0 0x2320000 0x0 0x10000>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			little-endian;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio3: gpio@2330000 {
+			compatible = "fsl,qoriq-gpio";
+			reg = <0x0 0x2330000 0x0 0x10000>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			little-endian;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		watchdog@23a0000 {
+			compatible = "arm,sbsa-gwdt";
+			reg = <0x0 0x23a0000 0 0x1000>,
+			      <0x0 0x2390000 0 0x1000>;
+			interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+			timeout-sec = <30>;
+		};
+
+		usb0: usb@3100000 {
+			compatible = "snps,dwc3";
+			reg = <0x0 0x3100000 0x0 0x10000>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+			dr_mode = "host";
+			snps,quirk-frame-length-adjustment = <0x20>;
+			snps,dis_rxdet_inp3_quirk;
+			status = "disabled";
+		};
+
+		usb1: usb@3110000 {
+			compatible = "snps,dwc3";
+			reg = <0x0 0x3110000 0x0 0x10000>;
+			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+			dr_mode = "host";
+			snps,quirk-frame-length-adjustment = <0x20>;
+			snps,dis_rxdet_inp3_quirk;
+			status = "disabled";
+		};
+
+		smmu: iommu@5000000 {
+			compatible = "arm,mmu-500";
+			reg = <0 0x5000000 0 0x800000>;
+			#iommu-cells = <1>;
+			#global-interrupts = <14>;
+				     // global secure fault
+			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+				     // combined secure
+				     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+				     // global non-secure fault
+				     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+				     // combined non-secure
+				     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+				     // performance counter interrupts 0-9
+				     <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>,
+				     // per context interrupt, 64 interrupts
+				     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
+			dma-coherent;
+		};
+	};
+};
-- 
2.7.4


^ permalink raw reply	[flat|nested] 10+ messages in thread

* [PATCH v5 6/6] arm64: dts: add LX2160ARDB board support
  2018-10-14 17:07 [PATCH v5 0/6] arm64: dts: NXP: add basic dts file for LX2160A SoC Vabhav Sharma
                   ` (4 preceding siblings ...)
  2018-10-14 17:08 ` [PATCH v5 5/6] arm64: dts: add QorIQ LX2160A SoC support Vabhav Sharma
@ 2018-10-14 17:08 ` Vabhav Sharma
  2018-10-24 21:41   ` Li Yang
  5 siblings, 1 reply; 10+ messages in thread
From: Vabhav Sharma @ 2018-10-14 17:08 UTC (permalink / raw)
  To: sudeep.holla, oss, linux-kernel, devicetree, robh+dt,
	mark.rutland, linuxppc-dev, linux-arm-kernel, mturquette, sboyd,
	rjw, viresh.kumar, linux-clk, linux-pm, linux-kernel-owner,
	catalin.marinas, will.deacon, gregkh, arnd, kstewart,
	yamada.masahiro, leoyang.li, shawnguo
  Cc: linux, adrian.hunter, ulf.hansson, V.Sethi, udit.kumar,
	pankaj.bansal, Vabhav Sharma, Priyanka Jain, Sriram Dash,
	Horia Geanta, Ran Wang, Zhang Ying-22455, Yinbo Zhu

LX2160A reference design board (RDB) is a high-performance
computing, evaluation, and development platform with LX2160A
SoC.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Horia Geanta <horia.geanta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Zhang Ying-22455 <ying.zhang22455@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
---
 arch/arm64/boot/dts/freescale/Makefile            |   1 +
 arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts | 119 ++++++++++++++++++++++
 2 files changed, 120 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 86e18ad..445b72b 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -13,3 +13,4 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts
new file mode 100644
index 0000000..6481e5f
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts
@@ -0,0 +1,119 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Device Tree file for LX2160ARDB
+//
+// Copyright 2018 NXP
+
+/dts-v1/;
+
+#include "fsl-lx2160a.dtsi"
+
+/ {
+	model = "NXP Layerscape LX2160ARDB";
+	compatible = "fsl,lx2160a-rdb", "fsl,lx2160a";
+
+	aliases {
+		crypto = &crypto;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	sb_3v3: regulator-sb3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "MC34717-3.3VSB";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+};
+
+&crypto {
+	status = "okay";
+};
+
+&esdhc0 {
+	sd-uhs-sdr104;
+	sd-uhs-sdr50;
+	sd-uhs-sdr25;
+	sd-uhs-sdr12;
+	status = "okay";
+};
+
+&esdhc1 {
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	bus-width = <8>;
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	i2c-mux@77 {
+		compatible = "nxp,pca9547";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+
+			power-monitor@40 {
+				compatible = "ti,ina220";
+				reg = <0x40>;
+				shunt-resistor = <1000>;
+			};
+		};
+
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+
+			temperature-sensor@4c {
+				compatible = "nxp,sa56004";
+				reg = <0x4c>;
+				vcc-supply = <&sb_3v3>;
+			};
+
+			temperature-sensor@4d {
+				compatible = "nxp,sa56004";
+				reg = <0x4d>;
+				vcc-supply = <&sb_3v3>;
+			};
+		};
+	};
+};
+
+&i2c4 {
+	status = "okay";
+
+	rtc@51 {
+		compatible = "nxp,pcf2129";
+		reg = <0x51>;
+		// IRQ10_B
+		interrupts = <0 150 0x4>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
-- 
2.7.4


^ permalink raw reply	[flat|nested] 10+ messages in thread

* Re: [PATCH v5 3/6] clk: qoriq: increase array size of cmux_to_group
  2018-10-14 17:08 ` [PATCH v5 3/6] clk: qoriq: increase array size of cmux_to_group Vabhav Sharma
@ 2018-10-16 22:44   ` Stephen Boyd
  0 siblings, 0 replies; 10+ messages in thread
From: Stephen Boyd @ 2018-10-16 22:44 UTC (permalink / raw)
  To: Vabhav Sharma, arnd, catalin.marinas, devicetree, gregkh,
	kstewart, leoyang.li, linux-arm-kernel, linux-clk,
	linux-kernel-owner, linux-kernel, linux-pm, linuxppc-dev,
	mark.rutland, mturquette, oss, rjw, robh+dt, shawnguo,
	sudeep.holla, viresh.kumar, will.deacon, yamada.masahiro
  Cc: linux, adrian.hunter, ulf.hansson, V.Sethi, udit.kumar,
	pankaj.bansal, Yogesh Gaur, Vabhav Sharma

Quoting Vabhav Sharma (2018-10-14 10:08:00)
> From: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
> 
> Increase size of cmux_to_group array, to accomdate entry of
> -1 termination.
> 
> Added -1, terminated, entry for 4080_cmux_grpX.
> 
> Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
> Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
> ---

Acked-by: Stephen Boyd <sboyd@kernel.org>


^ permalink raw reply	[flat|nested] 10+ messages in thread

* Re: [PATCH v5 2/6] soc/fsl/guts: Add definition for LX2160A
  2018-10-14 17:07 ` [PATCH v5 2/6] soc/fsl/guts: Add definition " Vabhav Sharma
@ 2018-10-24 21:39   ` Li Yang
  0 siblings, 0 replies; 10+ messages in thread
From: Li Yang @ 2018-10-24 21:39 UTC (permalink / raw)
  To: Vabhav Sharma
  Cc: Sudeep Holla, Scott Wood, lkml,
	open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
	Rob Herring, Mark Rutland, linuxppc-dev,
	moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE,
	Michael Turquette, sboyd, Rafael J. Wysocki, Viresh Kumar,
	linux-clk, linux-pm, linux-kernel-owner, Catalin Marinas,
	Will Deacon, Greg Kroah-Hartman, Arnd Bergmann, Kate Stewart,
	yamada.masahiro, Shawn Guo, Russell King, Adrian Hunter,
	Ulf Hansson, V.Sethi, udit.kumar, pankaj.bansal, Yinbo Zhu

On Mon, Oct 15, 2018 at 12:14 AM Vabhav Sharma <vabhav.sharma@nxp.com> wrote:
>
> Adding compatible string "lx2160a-dcfg" to
> initialize guts driver for lx2160 and SoC die
> attribute definition for LX2160A
>
> Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
> Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>

Acked-by: Li Yang <leoyang.li@nxp.com>

> ---
>  drivers/soc/fsl/guts.c | 6 ++++++
>  1 file changed, 6 insertions(+)
>
> diff --git a/drivers/soc/fsl/guts.c b/drivers/soc/fsl/guts.c
> index 302e0c8..bcab1ee 100644
> --- a/drivers/soc/fsl/guts.c
> +++ b/drivers/soc/fsl/guts.c
> @@ -100,6 +100,11 @@ static const struct fsl_soc_die_attr fsl_soc_die[] = {
>           .svr          = 0x87000000,
>           .mask         = 0xfff70000,
>         },
> +       /* Die: LX2160A, SoC: LX2160A/LX2120A/LX2080A */
> +       { .die          = "LX2160A",
> +         .svr          = 0x87360000,
> +         .mask         = 0xff3f0000,
> +       },
>         { },
>  };
>
> @@ -222,6 +227,7 @@ static const struct of_device_id fsl_guts_of_match[] = {
>         { .compatible = "fsl,ls1088a-dcfg", },
>         { .compatible = "fsl,ls1012a-dcfg", },
>         { .compatible = "fsl,ls1046a-dcfg", },
> +       { .compatible = "fsl,lx2160a-dcfg", },
>         {}
>  };
>  MODULE_DEVICE_TABLE(of, fsl_guts_of_match);
> --
> 2.7.4
>

^ permalink raw reply	[flat|nested] 10+ messages in thread

* Re: [PATCH v5 6/6] arm64: dts: add LX2160ARDB board support
  2018-10-14 17:08 ` [PATCH v5 6/6] arm64: dts: add LX2160ARDB board support Vabhav Sharma
@ 2018-10-24 21:41   ` Li Yang
  0 siblings, 0 replies; 10+ messages in thread
From: Li Yang @ 2018-10-24 21:41 UTC (permalink / raw)
  To: Vabhav Sharma
  Cc: Sudeep Holla, Scott Wood, lkml,
	open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
	Rob Herring, Mark Rutland, linuxppc-dev,
	moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE,
	Michael Turquette, sboyd, Rafael J. Wysocki, Viresh Kumar,
	linux-clk, linux-pm, linux-kernel-owner, Catalin Marinas,
	Will Deacon, Greg Kroah-Hartman, Arnd Bergmann, Kate Stewart,
	yamada.masahiro, Shawn Guo, Russell King, Adrian Hunter,
	Ulf Hansson, V.Sethi, udit.kumar, pankaj.bansal, Priyanka Jain,
	Sriram Dash, Horia Geanta, Ran Wang, Ying Zhang, Yinbo Zhu

On Mon, Oct 15, 2018 at 12:14 AM Vabhav Sharma <vabhav.sharma@nxp.com> wrote:
>
> LX2160A reference design board (RDB) is a high-performance
> computing, evaluation, and development platform with LX2160A
> SoC.
>
> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
> Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
> Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
> Signed-off-by: Horia Geanta <horia.geanta@nxp.com>
> Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
> Signed-off-by: Zhang Ying-22455 <ying.zhang22455@nxp.com>
> Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>

Acked-by: Li Yang <leoyang.li@nxp.com>

> ---
>  arch/arm64/boot/dts/freescale/Makefile            |   1 +
>  arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts | 119 ++++++++++++++++++++++
>  2 files changed, 120 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index 86e18ad..445b72b 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -13,3 +13,4 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
>  dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
>  dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
>  dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
> +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
> diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts
> new file mode 100644
> index 0000000..6481e5f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts
> @@ -0,0 +1,119 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +//
> +// Device Tree file for LX2160ARDB
> +//
> +// Copyright 2018 NXP
> +
> +/dts-v1/;
> +
> +#include "fsl-lx2160a.dtsi"
> +
> +/ {
> +       model = "NXP Layerscape LX2160ARDB";
> +       compatible = "fsl,lx2160a-rdb", "fsl,lx2160a";
> +
> +       aliases {
> +               crypto = &crypto;
> +               serial0 = &uart0;
> +       };
> +
> +       chosen {
> +               stdout-path = "serial0:115200n8";
> +       };
> +
> +       sb_3v3: regulator-sb3v3 {
> +               compatible = "regulator-fixed";
> +               regulator-name = "MC34717-3.3VSB";
> +               regulator-min-microvolt = <3300000>;
> +               regulator-max-microvolt = <3300000>;
> +               regulator-boot-on;
> +               regulator-always-on;
> +       };
> +};
> +
> +&crypto {
> +       status = "okay";
> +};
> +
> +&esdhc0 {
> +       sd-uhs-sdr104;
> +       sd-uhs-sdr50;
> +       sd-uhs-sdr25;
> +       sd-uhs-sdr12;
> +       status = "okay";
> +};
> +
> +&esdhc1 {
> +       mmc-hs200-1_8v;
> +       mmc-hs400-1_8v;
> +       bus-width = <8>;
> +       status = "okay";
> +};
> +
> +&i2c0 {
> +       status = "okay";
> +
> +       i2c-mux@77 {
> +               compatible = "nxp,pca9547";
> +               reg = <0x77>;
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +
> +               i2c@2 {
> +                       #address-cells = <1>;
> +                       #size-cells = <0>;
> +                       reg = <0x2>;
> +
> +                       power-monitor@40 {
> +                               compatible = "ti,ina220";
> +                               reg = <0x40>;
> +                               shunt-resistor = <1000>;
> +                       };
> +               };
> +
> +               i2c@3 {
> +                       #address-cells = <1>;
> +                       #size-cells = <0>;
> +                       reg = <0x3>;
> +
> +                       temperature-sensor@4c {
> +                               compatible = "nxp,sa56004";
> +                               reg = <0x4c>;
> +                               vcc-supply = <&sb_3v3>;
> +                       };
> +
> +                       temperature-sensor@4d {
> +                               compatible = "nxp,sa56004";
> +                               reg = <0x4d>;
> +                               vcc-supply = <&sb_3v3>;
> +                       };
> +               };
> +       };
> +};
> +
> +&i2c4 {
> +       status = "okay";
> +
> +       rtc@51 {
> +               compatible = "nxp,pcf2129";
> +               reg = <0x51>;
> +               // IRQ10_B
> +               interrupts = <0 150 0x4>;
> +       };
> +};
> +
> +&uart0 {
> +       status = "okay";
> +};
> +
> +&uart1 {
> +       status = "okay";
> +};
> +
> +&usb0 {
> +       status = "okay";
> +};
> +
> +&usb1 {
> +       status = "okay";
> +};
> --
> 2.7.4
>

^ permalink raw reply	[flat|nested] 10+ messages in thread

end of thread, other threads:[~2018-10-24 21:41 UTC | newest]

Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-10-14 17:07 [PATCH v5 0/6] arm64: dts: NXP: add basic dts file for LX2160A SoC Vabhav Sharma
2018-10-14 17:07 ` [PATCH v5 1/6] dt-bindings: arm64: add compatible for LX2160A Vabhav Sharma
2018-10-14 17:07 ` [PATCH v5 2/6] soc/fsl/guts: Add definition " Vabhav Sharma
2018-10-24 21:39   ` Li Yang
2018-10-14 17:08 ` [PATCH v5 3/6] clk: qoriq: increase array size of cmux_to_group Vabhav Sharma
2018-10-16 22:44   ` Stephen Boyd
2018-10-14 17:08 ` [PATCH v5 4/6] clk: qoriq: Add clockgen support for lx2160a Vabhav Sharma
2018-10-14 17:08 ` [PATCH v5 5/6] arm64: dts: add QorIQ LX2160A SoC support Vabhav Sharma
2018-10-14 17:08 ` [PATCH v5 6/6] arm64: dts: add LX2160ARDB board support Vabhav Sharma
2018-10-24 21:41   ` Li Yang

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).