* [PATCH v2 0/1] pwm: mediatek: add longer period support
@ 2020-03-03 10:19 Sam Shih
2020-03-03 10:19 ` [PATCH v2 1/1] " Sam Shih
0 siblings, 1 reply; 6+ messages in thread
From: Sam Shih @ 2020-03-03 10:19 UTC (permalink / raw)
To: Thierry Reding, Uwe Kleine-König, Matthias Brugger
Cc: John Crispin, linux-pwm, linux-kernel, linux-arm-kernel,
linux-mediatek, Sam Shih
This patch add support for longer pwm period configuration,
which allowing blinking LEDs via pwm interface.
Sam Shih (1):
pwm: mediatek: add longer period support
drivers/pwm/pwm-mediatek.c | 34 ++++++++++++++++++++++++++++++----
1 file changed, 30 insertions(+), 4 deletions(-)
--
2.17.1
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v2 1/1] pwm: mediatek: add longer period support
2020-03-03 10:19 [PATCH v2 0/1] pwm: mediatek: add longer period support Sam Shih
@ 2020-03-03 10:19 ` Sam Shih
2020-03-06 7:41 ` Uwe Kleine-König
2020-03-07 21:28 ` Matthias Brugger
0 siblings, 2 replies; 6+ messages in thread
From: Sam Shih @ 2020-03-03 10:19 UTC (permalink / raw)
To: Thierry Reding, Uwe Kleine-König, Matthias Brugger
Cc: John Crispin, linux-pwm, linux-kernel, linux-arm-kernel,
linux-mediatek, Sam Shih
The pwm clock source could be divided by 1625 with PWM_CON
BIT(3) setting in mediatek hardware.
This patch add support for longer pwm period configuration,
which allowing blinking LEDs via pwm interface.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
---
drivers/pwm/pwm-mediatek.c | 34 ++++++++++++++++++++++++++++++----
1 file changed, 30 insertions(+), 4 deletions(-)
diff --git a/drivers/pwm/pwm-mediatek.c b/drivers/pwm/pwm-mediatek.c
index b94e0d09c300..c64ecff6c550 100644
--- a/drivers/pwm/pwm-mediatek.c
+++ b/drivers/pwm/pwm-mediatek.c
@@ -121,8 +121,11 @@ static int pwm_mediatek_config(struct pwm_chip *chip, struct pwm_device *pwm,
int duty_ns, int period_ns)
{
struct pwm_mediatek_chip *pc = to_pwm_mediatek_chip(chip);
- u32 clkdiv = 0, cnt_period, cnt_duty, reg_width = PWMDWIDTH,
- reg_thres = PWMTHRES;
+ /* The source clock is divided by 2^clkdiv or iff the clksel bit
+ * is set by (2^clkdiv*1625)
+ */
+ u32 clkdiv = 0, clksel = 0, cnt_period, cnt_duty,
+ reg_width = PWMDWIDTH, reg_thres = PWMTHRES;
u64 resolution;
int ret;
@@ -133,12 +136,30 @@ static int pwm_mediatek_config(struct pwm_chip *chip, struct pwm_device *pwm,
/* Using resolution in picosecond gets accuracy higher */
resolution = (u64)NSEC_PER_SEC * 1000;
+ /* Calculate resolution based on current clock frequency */
do_div(resolution, clk_get_rate(pc->clk_pwms[pwm->hwpwm]));
-
+ /* Using resolution to calculate cnt_period which represents
+ * the effective range of the PWM period counter
+ */
cnt_period = DIV_ROUND_CLOSEST_ULL((u64)period_ns * 1000, resolution);
while (cnt_period > 8191) {
+ /* Using clkdiv to reduce clock frequency and calculate
+ * new resolution based on new clock speed
+ */
resolution *= 2;
clkdiv++;
+ if (clkdiv > PWM_CLK_DIV_MAX && !clksel) {
+ /* Using clksel to divide the pwm source clock by
+ * an additional 1625, and recalculate new clkdiv
+ * and resolution
+ */
+ clksel = 1;
+ clkdiv = 0;
+ resolution = (u64)NSEC_PER_SEC * 1000 * 1625;
+ do_div(resolution,
+ clk_get_rate(pc->clk_pwms[pwm->hwpwm]));
+ }
+ /* Calculate cnt_period based on resolution */
cnt_period = DIV_ROUND_CLOSEST_ULL((u64)period_ns * 1000,
resolution);
}
@@ -158,8 +179,13 @@ static int pwm_mediatek_config(struct pwm_chip *chip, struct pwm_device *pwm,
reg_thres = PWM45THRES_FIXUP;
}
+ /* Calculate cnt_duty based on resolution */
cnt_duty = DIV_ROUND_CLOSEST_ULL((u64)duty_ns * 1000, resolution);
- pwm_mediatek_writel(pc, pwm->hwpwm, PWMCON, BIT(15) | clkdiv);
+ if (clksel)
+ pwm_mediatek_writel(pc, pwm->hwpwm, PWMCON, BIT(15) | BIT(3) |
+ clkdiv);
+ else
+ pwm_mediatek_writel(pc, pwm->hwpwm, PWMCON, BIT(15) | clkdiv);
pwm_mediatek_writel(pc, pwm->hwpwm, reg_width, cnt_period);
pwm_mediatek_writel(pc, pwm->hwpwm, reg_thres, cnt_duty);
--
2.17.1
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH v2 1/1] pwm: mediatek: add longer period support
2020-03-03 10:19 ` [PATCH v2 1/1] " Sam Shih
@ 2020-03-06 7:41 ` Uwe Kleine-König
2020-03-07 21:28 ` Matthias Brugger
1 sibling, 0 replies; 6+ messages in thread
From: Uwe Kleine-König @ 2020-03-06 7:41 UTC (permalink / raw)
To: Sam Shih
Cc: Thierry Reding, Matthias Brugger, John Crispin, linux-pwm,
linux-kernel, linux-arm-kernel, linux-mediatek
On Tue, Mar 03, 2020 at 06:19:15PM +0800, Sam Shih wrote:
> The pwm clock source could be divided by 1625 with PWM_CON
> BIT(3) setting in mediatek hardware.
>
> This patch add support for longer pwm period configuration,
> which allowing blinking LEDs via pwm interface.
>
> Signed-off-by: Sam Shih <sam.shih@mediatek.com>
> ---
> drivers/pwm/pwm-mediatek.c | 34 ++++++++++++++++++++++++++++++----
> 1 file changed, 30 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/pwm/pwm-mediatek.c b/drivers/pwm/pwm-mediatek.c
> index b94e0d09c300..c64ecff6c550 100644
> --- a/drivers/pwm/pwm-mediatek.c
> +++ b/drivers/pwm/pwm-mediatek.c
> @@ -121,8 +121,11 @@ static int pwm_mediatek_config(struct pwm_chip *chip, struct pwm_device *pwm,
> int duty_ns, int period_ns)
> {
> struct pwm_mediatek_chip *pc = to_pwm_mediatek_chip(chip);
> - u32 clkdiv = 0, cnt_period, cnt_duty, reg_width = PWMDWIDTH,
> - reg_thres = PWMTHRES;
> + /* The source clock is divided by 2^clkdiv or iff the clksel bit
> + * is set by (2^clkdiv*1625)
> + */
Please put the /* on it's own line. See
https://www.kernel.org/doc/html/latest/process/coding-style.html#commenting
> + u32 clkdiv = 0, clksel = 0, cnt_period, cnt_duty,
> + reg_width = PWMDWIDTH, reg_thres = PWMTHRES;
> u64 resolution;
> int ret;
>
> @@ -133,12 +136,30 @@ static int pwm_mediatek_config(struct pwm_chip *chip, struct pwm_device *pwm,
>
> /* Using resolution in picosecond gets accuracy higher */
> resolution = (u64)NSEC_PER_SEC * 1000;
> + /* Calculate resolution based on current clock frequency */
> do_div(resolution, clk_get_rate(pc->clk_pwms[pwm->hwpwm]));
> -
> + /* Using resolution to calculate cnt_period which represents
> + * the effective range of the PWM period counter
> + */
> cnt_period = DIV_ROUND_CLOSEST_ULL((u64)period_ns * 1000, resolution);
The existing code is rather bad. A better approach to calulate
cnt_period (with a single division and higher accuracy):
cnt_period = DIV_ROUND_CLOSEST_ULL((u64)period_ns * clk_get_rate(..), NSEC_PER_SEC);
> while (cnt_period > 8191) {
> + /* Using clkdiv to reduce clock frequency and calculate
> + * new resolution based on new clock speed
> + */
> resolution *= 2;
> clkdiv++;
> + if (clkdiv > PWM_CLK_DIV_MAX && !clksel) {
> + /* Using clksel to divide the pwm source clock by
> + * an additional 1625, and recalculate new clkdiv
> + * and resolution
> + */
> + clksel = 1;
> + clkdiv = 0;
> + resolution = (u64)NSEC_PER_SEC * 1000 * 1625;
> + do_div(resolution,
> + clk_get_rate(pc->clk_pwms[pwm->hwpwm]));
> + }
> + /* Calculate cnt_period based on resolution */
> cnt_period = DIV_ROUND_CLOSEST_ULL((u64)period_ns * 1000,
> resolution);
> }
> @@ -158,8 +179,13 @@ static int pwm_mediatek_config(struct pwm_chip *chip, struct pwm_device *pwm,
> reg_thres = PWM45THRES_FIXUP;
> }
>
> + /* Calculate cnt_duty based on resolution */
> cnt_duty = DIV_ROUND_CLOSEST_ULL((u64)duty_ns * 1000, resolution);
Using resolution as divisor is bad here, too, so the way to calculate
cnt_duty should be changed accordingly.
I think if the driver is simplified first, maybe even getting rid of the
while loop, your change will get considerably easier, too.
> - pwm_mediatek_writel(pc, pwm->hwpwm, PWMCON, BIT(15) | clkdiv);
> + if (clksel)
> + pwm_mediatek_writel(pc, pwm->hwpwm, PWMCON, BIT(15) | BIT(3) |
> + clkdiv);
> + else
> + pwm_mediatek_writel(pc, pwm->hwpwm, PWMCON, BIT(15) | clkdiv);
> pwm_mediatek_writel(pc, pwm->hwpwm, reg_width, cnt_period);
> pwm_mediatek_writel(pc, pwm->hwpwm, reg_thres, cnt_duty);
Best regards
Uwe
--
Pengutronix e.K. | Uwe Kleine-König |
Industrial Linux Solutions | https://www.pengutronix.de/ |
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v2 1/1] pwm: mediatek: add longer period support
2020-03-03 10:19 ` [PATCH v2 1/1] " Sam Shih
2020-03-06 7:41 ` Uwe Kleine-König
@ 2020-03-07 21:28 ` Matthias Brugger
2020-03-08 20:18 ` Uwe Kleine-König
1 sibling, 1 reply; 6+ messages in thread
From: Matthias Brugger @ 2020-03-07 21:28 UTC (permalink / raw)
To: Sam Shih, Thierry Reding, Uwe Kleine-König
Cc: John Crispin, linux-pwm, linux-kernel, linux-arm-kernel, linux-mediatek
On 03/03/2020 11:19, Sam Shih wrote:
> The pwm clock source could be divided by 1625 with PWM_CON
> BIT(3) setting in mediatek hardware.
>
> This patch add support for longer pwm period configuration,
> which allowing blinking LEDs via pwm interface.
Is this a fix? In this case please provide a Fixes tag with the commit ID which
introduced the bug.
Thanks
Matthias
>
> Signed-off-by: Sam Shih <sam.shih@mediatek.com>
> ---
> drivers/pwm/pwm-mediatek.c | 34 ++++++++++++++++++++++++++++++----
> 1 file changed, 30 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/pwm/pwm-mediatek.c b/drivers/pwm/pwm-mediatek.c
> index b94e0d09c300..c64ecff6c550 100644
> --- a/drivers/pwm/pwm-mediatek.c
> +++ b/drivers/pwm/pwm-mediatek.c
> @@ -121,8 +121,11 @@ static int pwm_mediatek_config(struct pwm_chip *chip, struct pwm_device *pwm,
> int duty_ns, int period_ns)
> {
> struct pwm_mediatek_chip *pc = to_pwm_mediatek_chip(chip);
> - u32 clkdiv = 0, cnt_period, cnt_duty, reg_width = PWMDWIDTH,
> - reg_thres = PWMTHRES;
> + /* The source clock is divided by 2^clkdiv or iff the clksel bit
> + * is set by (2^clkdiv*1625)
> + */
> + u32 clkdiv = 0, clksel = 0, cnt_period, cnt_duty,
> + reg_width = PWMDWIDTH, reg_thres = PWMTHRES;
> u64 resolution;
> int ret;
>
> @@ -133,12 +136,30 @@ static int pwm_mediatek_config(struct pwm_chip *chip, struct pwm_device *pwm,
>
> /* Using resolution in picosecond gets accuracy higher */
> resolution = (u64)NSEC_PER_SEC * 1000;
> + /* Calculate resolution based on current clock frequency */
> do_div(resolution, clk_get_rate(pc->clk_pwms[pwm->hwpwm]));
> -
> + /* Using resolution to calculate cnt_period which represents
> + * the effective range of the PWM period counter
> + */
> cnt_period = DIV_ROUND_CLOSEST_ULL((u64)period_ns * 1000, resolution);
> while (cnt_period > 8191) {
> + /* Using clkdiv to reduce clock frequency and calculate
> + * new resolution based on new clock speed
> + */
> resolution *= 2;
> clkdiv++;
> + if (clkdiv > PWM_CLK_DIV_MAX && !clksel) {
> + /* Using clksel to divide the pwm source clock by
> + * an additional 1625, and recalculate new clkdiv
> + * and resolution
> + */
> + clksel = 1;
> + clkdiv = 0;
> + resolution = (u64)NSEC_PER_SEC * 1000 * 1625;
> + do_div(resolution,
> + clk_get_rate(pc->clk_pwms[pwm->hwpwm]));
> + }
> + /* Calculate cnt_period based on resolution */
> cnt_period = DIV_ROUND_CLOSEST_ULL((u64)period_ns * 1000,
> resolution);
> }
> @@ -158,8 +179,13 @@ static int pwm_mediatek_config(struct pwm_chip *chip, struct pwm_device *pwm,
> reg_thres = PWM45THRES_FIXUP;
> }
>
> + /* Calculate cnt_duty based on resolution */
> cnt_duty = DIV_ROUND_CLOSEST_ULL((u64)duty_ns * 1000, resolution);
> - pwm_mediatek_writel(pc, pwm->hwpwm, PWMCON, BIT(15) | clkdiv);
> + if (clksel)
> + pwm_mediatek_writel(pc, pwm->hwpwm, PWMCON, BIT(15) | BIT(3) |
> + clkdiv);
> + else
> + pwm_mediatek_writel(pc, pwm->hwpwm, PWMCON, BIT(15) | clkdiv);
> pwm_mediatek_writel(pc, pwm->hwpwm, reg_width, cnt_period);
> pwm_mediatek_writel(pc, pwm->hwpwm, reg_thres, cnt_duty);
>
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v2 1/1] pwm: mediatek: add longer period support
2020-03-07 21:28 ` Matthias Brugger
@ 2020-03-08 20:18 ` Uwe Kleine-König
2020-03-09 3:35 ` Sam Shih
0 siblings, 1 reply; 6+ messages in thread
From: Uwe Kleine-König @ 2020-03-08 20:18 UTC (permalink / raw)
To: Matthias Brugger
Cc: Sam Shih, Thierry Reding, John Crispin, linux-pwm, linux-kernel,
linux-arm-kernel, linux-mediatek
Hello,
On Sat, Mar 07, 2020 at 10:28:36PM +0100, Matthias Brugger wrote:
> On 03/03/2020 11:19, Sam Shih wrote:
> > The pwm clock source could be divided by 1625 with PWM_CON
> > BIT(3) setting in mediatek hardware.
> >
> > This patch add support for longer pwm period configuration,
> > which allowing blinking LEDs via pwm interface.
>
> Is this a fix? In this case please provide a Fixes tag with the commit ID which
> introduced the bug.
I'd say it qualifies as a fix if without it a request with a long period
returns success but isn't properly implemented. Otherwise it's only a
new feature.
Best regards
Uwe
--
Pengutronix e.K. | Uwe Kleine-König |
Industrial Linux Solutions | https://www.pengutronix.de/ |
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v2 1/1] pwm: mediatek: add longer period support
2020-03-08 20:18 ` Uwe Kleine-König
@ 2020-03-09 3:35 ` Sam Shih
0 siblings, 0 replies; 6+ messages in thread
From: Sam Shih @ 2020-03-09 3:35 UTC (permalink / raw)
To: Matthias Brugger, Uwe Kleine-König
Cc: linux-pwm, linux-kernel, Thierry Reding, linux-mediatek,
John Crispin, linux-arm-kernel
Hello,
On Sun, 2020-03-08 at 21:18 +0100, Uwe Kleine-König wrote:
> Hello,
>
> On Sat, Mar 07, 2020 at 10:28:36PM +0100, Matthias Brugger wrote:
> > On 03/03/2020 11:19, Sam Shih wrote:
> > > The pwm clock source could be divided by 1625 with PWM_CON
> > > BIT(3) setting in mediatek hardware.
> > >
> > > This patch add support for longer pwm period configuration,
> > > which allowing blinking LEDs via pwm interface.
> >
> > Is this a fix? In this case please provide a Fixes tag with the commit ID which
> > introduced the bug.
>
> I'd say it qualifies as a fix if without it a request with a long period
> returns success but isn't properly implemented. Otherwise it's only a
> new feature.
>
It's only a new feature.
Without this patch, pwm_mediatek_config return -EINVAL when receive a
long period request.
I will send v3 to reply Uwe's comment.
Best Regards,
Sam Shih
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2020-03-09 3:36 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-03-03 10:19 [PATCH v2 0/1] pwm: mediatek: add longer period support Sam Shih
2020-03-03 10:19 ` [PATCH v2 1/1] " Sam Shih
2020-03-06 7:41 ` Uwe Kleine-König
2020-03-07 21:28 ` Matthias Brugger
2020-03-08 20:18 ` Uwe Kleine-König
2020-03-09 3:35 ` Sam Shih
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).