* [PATCH] arm64: dts: qcom: sc7280: Add WPSS remoteproc node
@ 2021-03-10 7:37 Rakesh Pillai
2021-03-10 16:49 ` Bjorn Andersson
2021-03-15 13:54 ` Sibi Sankar
0 siblings, 2 replies; 3+ messages in thread
From: Rakesh Pillai @ 2021-03-10 7:37 UTC (permalink / raw)
To: agross, bjorn.andersson, robh+dt
Cc: sibis, linux-arm-msm, devicetree, linux-kernel, Rakesh Pillai
Add the WPSS remoteproc node in dts for
PIL loading.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
---
- This change is dependent on the below patch series
1) https://lore.kernel.org/patchwork/project/lkml/list/?series=487403
2) https://lore.kernel.org/patchwork/project/lkml/list/?series=488365
---
arch/arm64/boot/dts/qcom/sc7280-idp.dts | 4 +++
arch/arm64/boot/dts/qcom/sc7280.dtsi | 47 +++++++++++++++++++++++++++++++++
2 files changed, 51 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
index 950ecb2..603f56b 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
@@ -26,6 +26,10 @@
status = "okay";
};
+&remoteproc_wpss {
+ status = "okay";
+};
+
&uart5 {
status = "okay";
};
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 8af6d77..26dd466 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -53,6 +53,16 @@
no-map;
reg = <0x0 0x80b00000 0x0 0x100000>;
};
+
+ wlan_fw_mem: memory@80c00000 {
+ no-map;
+ reg = <0x0 0x80c00000 0x0 0xc00000>;
+ };
+
+ wpss_mem: memory@9ae00000 {
+ no-map;
+ reg = <0x0 0x9ae00000 0x0 0x1900000>;
+ };
};
cpus {
@@ -305,6 +315,43 @@
};
};
+ remoteproc_wpss: remoteproc@8a00000 {
+ compatible = "qcom,sc7280-wpss-pil";
+ reg = <0 0x08a00000 0 0x10000>;
+
+ interrupts-extended = <&intc GIC_SPI 587 IRQ_TYPE_EDGE_RISING>,
+ <&wpss_smp2p_in 0 0>,
+ <&wpss_smp2p_in 1 0>,
+ <&wpss_smp2p_in 2 0>,
+ <&wpss_smp2p_in 3 0>,
+ <&wpss_smp2p_in 7 0>;
+ interrupt-names = "wdog", "fatal", "ready", "handover",
+ "stop-ack", "shutdown-ack";
+
+ memory-region = <&wpss_mem>;
+
+ qcom,smem-states = <&wpss_smp2p_out 0>;
+ qcom,smem-state-names = "stop";
+
+ resets = <&aoss_reset AOSS_CC_WCSS_RESTART>;
+ reset-names = "restart";
+
+ qcom,halt-regs = <&tcsr_mutex_regs 0x37000>;
+
+ status = "disabled";
+
+ glink-edge {
+ interrupts-extended = <&ipcc IPCC_CLIENT_WPSS
+ IPCC_MPROC_SIGNAL_GLINK_QMP
+ IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&ipcc IPCC_CLIENT_WPSS
+ IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+ label = "wpss";
+ qcom,remote-pid = <13>;
+ };
+ };
+
pdc: interrupt-controller@b220000 {
compatible = "qcom,sc7280-pdc", "qcom,pdc";
reg = <0 0x0b220000 0 0x30000>;
--
2.7.4
^ permalink raw reply related [flat|nested] 3+ messages in thread* Re: [PATCH] arm64: dts: qcom: sc7280: Add WPSS remoteproc node
2021-03-10 7:37 [PATCH] arm64: dts: qcom: sc7280: Add WPSS remoteproc node Rakesh Pillai
@ 2021-03-10 16:49 ` Bjorn Andersson
2021-03-15 13:54 ` Sibi Sankar
1 sibling, 0 replies; 3+ messages in thread
From: Bjorn Andersson @ 2021-03-10 16:49 UTC (permalink / raw)
To: Rakesh Pillai
Cc: agross, robh+dt, sibis, linux-arm-msm, devicetree, linux-kernel
On Wed 10 Mar 01:37 CST 2021, Rakesh Pillai wrote:
> Add the WPSS remoteproc node in dts for
> PIL loading.
>
> Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
> ---
> - This change is dependent on the below patch series
> 1) https://lore.kernel.org/patchwork/project/lkml/list/?series=487403
> 2) https://lore.kernel.org/patchwork/project/lkml/list/?series=488365
> ---
> arch/arm64/boot/dts/qcom/sc7280-idp.dts | 4 +++
> arch/arm64/boot/dts/qcom/sc7280.dtsi | 47 +++++++++++++++++++++++++++++++++
> 2 files changed, 51 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
> index 950ecb2..603f56b 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
> @@ -26,6 +26,10 @@
> status = "okay";
> };
>
> +&remoteproc_wpss {
> + status = "okay";
> +};
> +
> &uart5 {
> status = "okay";
> };
> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> index 8af6d77..26dd466 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> @@ -53,6 +53,16 @@
> no-map;
> reg = <0x0 0x80b00000 0x0 0x100000>;
> };
> +
> + wlan_fw_mem: memory@80c00000 {
> + no-map;
> + reg = <0x0 0x80c00000 0x0 0xc00000>;
> + };
> +
> + wpss_mem: memory@9ae00000 {
> + no-map;
> + reg = <0x0 0x9ae00000 0x0 0x1900000>;
> + };
> };
>
> cpus {
> @@ -305,6 +315,43 @@
> };
> };
>
> + remoteproc_wpss: remoteproc@8a00000 {
> + compatible = "qcom,sc7280-wpss-pil";
> + reg = <0 0x08a00000 0 0x10000>;
> +
> + interrupts-extended = <&intc GIC_SPI 587 IRQ_TYPE_EDGE_RISING>,
> + <&wpss_smp2p_in 0 0>,
IRQ_TYPE_NONE?
Apart from that this looks good.
Regards,
Bjorn
> + <&wpss_smp2p_in 1 0>,
> + <&wpss_smp2p_in 2 0>,
> + <&wpss_smp2p_in 3 0>,
> + <&wpss_smp2p_in 7 0>;
> + interrupt-names = "wdog", "fatal", "ready", "handover",
> + "stop-ack", "shutdown-ack";
> +
> + memory-region = <&wpss_mem>;
> +
> + qcom,smem-states = <&wpss_smp2p_out 0>;
> + qcom,smem-state-names = "stop";
> +
> + resets = <&aoss_reset AOSS_CC_WCSS_RESTART>;
> + reset-names = "restart";
> +
> + qcom,halt-regs = <&tcsr_mutex_regs 0x37000>;
> +
> + status = "disabled";
> +
> + glink-edge {
> + interrupts-extended = <&ipcc IPCC_CLIENT_WPSS
> + IPCC_MPROC_SIGNAL_GLINK_QMP
> + IRQ_TYPE_EDGE_RISING>;
> + mboxes = <&ipcc IPCC_CLIENT_WPSS
> + IPCC_MPROC_SIGNAL_GLINK_QMP>;
> +
> + label = "wpss";
> + qcom,remote-pid = <13>;
> + };
> + };
> +
> pdc: interrupt-controller@b220000 {
> compatible = "qcom,sc7280-pdc", "qcom,pdc";
> reg = <0 0x0b220000 0 0x30000>;
> --
> 2.7.4
>
^ permalink raw reply [flat|nested] 3+ messages in thread* Re: [PATCH] arm64: dts: qcom: sc7280: Add WPSS remoteproc node
2021-03-10 7:37 [PATCH] arm64: dts: qcom: sc7280: Add WPSS remoteproc node Rakesh Pillai
2021-03-10 16:49 ` Bjorn Andersson
@ 2021-03-15 13:54 ` Sibi Sankar
1 sibling, 0 replies; 3+ messages in thread
From: Sibi Sankar @ 2021-03-15 13:54 UTC (permalink / raw)
To: Rakesh Pillai
Cc: agross, bjorn.andersson, robh+dt, linux-arm-msm, devicetree,
linux-kernel
On 2021-03-10 13:07, Rakesh Pillai wrote:
> Add the WPSS remoteproc node in dts for
> PIL loading.
>
> Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
> ---
> - This change is dependent on the below patch series
> 1) https://lore.kernel.org/patchwork/project/lkml/list/?series=487403
> 2) https://lore.kernel.org/patchwork/project/lkml/list/?series=488365
> ---
> arch/arm64/boot/dts/qcom/sc7280-idp.dts | 4 +++
> arch/arm64/boot/dts/qcom/sc7280.dtsi | 47
> +++++++++++++++++++++++++++++++++
> 2 files changed, 51 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
> b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
> index 950ecb2..603f56b 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
> @@ -26,6 +26,10 @@
> status = "okay";
> };
>
> +&remoteproc_wpss {
> + status = "okay";
> +};
> +
> &uart5 {
> status = "okay";
> };
> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi
> b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> index 8af6d77..26dd466 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> @@ -53,6 +53,16 @@
> no-map;
> reg = <0x0 0x80b00000 0x0 0x100000>;
> };
> +
> + wlan_fw_mem: memory@80c00000 {
> + no-map;
> + reg = <0x0 0x80c00000 0x0 0xc00000>;
> + };
> +
> + wpss_mem: memory@9ae00000 {
> + no-map;
> + reg = <0x0 0x9ae00000 0x0 0x1900000>;
> + };
The wpss mem shouldn't move into
board specific dt.
> };
>
> cpus {
> @@ -305,6 +315,43 @@
> };
> };
>
> + remoteproc_wpss: remoteproc@8a00000 {
> + compatible = "qcom,sc7280-wpss-pil";
please aim to add pas based
support to boot wpss as well.
> + reg = <0 0x08a00000 0 0x10000>;
> +
> + interrupts-extended = <&intc GIC_SPI 587 IRQ_TYPE_EDGE_RISING>,
> + <&wpss_smp2p_in 0 0>,
> + <&wpss_smp2p_in 1 0>,
> + <&wpss_smp2p_in 2 0>,
> + <&wpss_smp2p_in 3 0>,
> + <&wpss_smp2p_in 7 0>;
> + interrupt-names = "wdog", "fatal", "ready", "handover",
> + "stop-ack", "shutdown-ack";
> +
> + memory-region = <&wpss_mem>;
> +
looks like you missed adding clocks
and power-domains mentioned in the
bindings.
> + qcom,smem-states = <&wpss_smp2p_out 0>;
> + qcom,smem-state-names = "stop";
> +
> + resets = <&aoss_reset AOSS_CC_WCSS_RESTART>;
> + reset-names = "restart";
> +
> + qcom,halt-regs = <&tcsr_mutex_regs 0x37000>;
> +
> + status = "disabled";
> +
> + glink-edge {
> + interrupts-extended = <&ipcc IPCC_CLIENT_WPSS
> + IPCC_MPROC_SIGNAL_GLINK_QMP
> + IRQ_TYPE_EDGE_RISING>;
> + mboxes = <&ipcc IPCC_CLIENT_WPSS
> + IPCC_MPROC_SIGNAL_GLINK_QMP>;
> +
> + label = "wpss";
> + qcom,remote-pid = <13>;
> + };
> + };
> +
> pdc: interrupt-controller@b220000 {
> compatible = "qcom,sc7280-pdc", "qcom,pdc";
> reg = <0 0x0b220000 0 0x30000>;
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project.
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2021-03-15 14:00 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-03-10 7:37 [PATCH] arm64: dts: qcom: sc7280: Add WPSS remoteproc node Rakesh Pillai
2021-03-10 16:49 ` Bjorn Andersson
2021-03-15 13:54 ` Sibi Sankar
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).