* 2.4.21-pre7, 2.5.66, IDE Errors during boot - just a nuisance ?
@ 2003-04-10 7:54 Michael Frank
2003-04-10 8:02 ` Andre Hedrick
2003-04-11 7:39 ` Jarmo Järvenpää
0 siblings, 2 replies; 5+ messages in thread
From: Michael Frank @ 2003-04-10 7:54 UTC (permalink / raw)
To: linux-kernel
Noticed this for some time in 2.5.64 and up, and now also in 2.4.21-pre6 and pre7. It was OK 2.4.20. No functional problems were encountered with 2.4.21, 2.5.6x so far.
Its a P1, lspci follows
00:00.0 Host bridge: Intel Corp. 430HX - 82439HX TXC [Triton II] (rev 03)
00:07.0 ISA bridge: Intel Corp. 82371SB PIIX3 ISA [Natoma/Triton II] (rev 01)
00:07.1 IDE interface: Intel Corp. 82371SB PIIX3 IDE [Natoma/Triton II]
00:09.0 VGA compatible controller: S3 Inc. ViRGE/DX or /GX (rev 01)
00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
00:0b.0 SCSI storage controller: Adaptec AHA-7850 (rev 01)
Apr 10 15:17:30 mhfl1 kernel: Linux version 2.4.21-pre7-mhf18-np (mhf@mhfl3) (gcc version 2.95.3 20010315 (release)) #2
Apr 10 15:12:42 mhfl1 kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
Apr 10 15:12:42 mhfl1 kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Apr 10 15:12:42 mhfl1 kernel: PIIX3: IDE controller at PCI slot 00:07.1
Apr 10 15:12:42 mhfl1 kernel: PIIX3: chipset revision 0
Apr 10 15:12:42 mhfl1 kernel: PIIX3: not 100%% native mode: will probe irqs later
Apr 10 15:12:42 mhfl1 kernel: ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
Apr 10 15:12:42 mhfl1 kernel: ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
Apr 10 15:12:42 mhfl1 kernel: hda: QUANTUM BIGFOOT2550A, ATA DISK drive
Apr 10 15:12:42 mhfl1 kernel: blk: queue c0347ae0, I/O limit 4095Mb (mask 0xffffffff)
Apr 10 15:12:42 mhfl1 kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Apr 10 15:12:43 mhfl1 kernel: hda: attached ide-disk driver.
------------------------------\/
Apr 10 15:12:43 mhfl1 kernel: hda: task_no_data_intr: status=0x53 { DriveReady SeekComplete Index Error }
Apr 10 15:12:43 mhfl1 kernel: hda: task_no_data_intr: error=0x04 { DriveStatusError }
Apr 10 15:12:43 mhfl1 kernel: hda: 5033952 sectors (2577 MB) w/87KiB Cache, CHS=624/128/63, DMA
Apr 10 15:12:43 mhfl1 kernel: Partition check:
Apr 10 15:12:43 mhfl1 kernel: hda: hda1 hda2 hda3
----------
Mar 30 15:46:51 mhfl1 kernel: Linux version 2.5.66-mhf2 (mhf@mhfl2) (gcc version 2.95.3 20010315 (release)) #12 Sat Mar 29
Mar 30 15:47:05 mhfl1 kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Mar 30 15:47:05 mhfl1 kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Mar 30 15:47:05 mhfl1 kernel: PIIX3: IDE controller at PCI slot 00:07.1
Mar 30 15:47:05 mhfl1 kernel: PIIX3: chipset revision 0
Mar 30 15:47:05 mhfl1 kernel: PIIX3: not 100%% native mode: will probe irqs later
Mar 30 15:47:05 mhfl1 kernel: ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
Mar 30 15:47:05 mhfl1 kernel: ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
Mar 30 15:47:05 mhfl1 kernel: hda: QUANTUM BIGFOOT2550A, ATA DISK drive
Mar 30 15:47:05 mhfl1 kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
------------------------------\/
Mar 30 15:47:05 mhfl1 kernel: hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
Mar 30 15:47:05 mhfl1 kernel: hda: task_no_data_intr: error=0x04 { DriveStatusError }
Mar 30 15:47:05 mhfl1 kernel: hda: 5033952 sectors (2577 MB) w/87KiB Cache, CHS=4994/16/63, DMA
Mar 30 15:47:05 mhfl1 kernel: hda: hda1 hda2 hda3
Regards
Michael
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: 2.4.21-pre7, 2.5.66, IDE Errors during boot - just a nuisance ?
2003-04-10 7:54 2.4.21-pre7, 2.5.66, IDE Errors during boot - just a nuisance ? Michael Frank
@ 2003-04-10 8:02 ` Andre Hedrick
2003-04-10 11:00 ` Rob van Nieuwkerk
2003-04-11 7:39 ` Jarmo Järvenpää
1 sibling, 1 reply; 5+ messages in thread
From: Andre Hedrick @ 2003-04-10 8:02 UTC (permalink / raw)
To: Michael Frank; +Cc: linux-kernel
All it is an aborted command.
just a nuisanse and noise maker!
On Thu, 10 Apr 2003, Michael Frank wrote:
> Noticed this for some time in 2.5.64 and up, and now also in 2.4.21-pre6 and pre7. It was OK 2.4.20. No functional problems were encountered with 2.4.21, 2.5.6x so far.
>
> Its a P1, lspci follows
>
> 00:00.0 Host bridge: Intel Corp. 430HX - 82439HX TXC [Triton II] (rev 03)
> 00:07.0 ISA bridge: Intel Corp. 82371SB PIIX3 ISA [Natoma/Triton II] (rev 01)
> 00:07.1 IDE interface: Intel Corp. 82371SB PIIX3 IDE [Natoma/Triton II]
> 00:09.0 VGA compatible controller: S3 Inc. ViRGE/DX or /GX (rev 01)
> 00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
> 00:0b.0 SCSI storage controller: Adaptec AHA-7850 (rev 01)
>
>
> Apr 10 15:17:30 mhfl1 kernel: Linux version 2.4.21-pre7-mhf18-np (mhf@mhfl3) (gcc version 2.95.3 20010315 (release)) #2
>
> Apr 10 15:12:42 mhfl1 kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
> Apr 10 15:12:42 mhfl1 kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> Apr 10 15:12:42 mhfl1 kernel: PIIX3: IDE controller at PCI slot 00:07.1
> Apr 10 15:12:42 mhfl1 kernel: PIIX3: chipset revision 0
> Apr 10 15:12:42 mhfl1 kernel: PIIX3: not 100%% native mode: will probe irqs later
> Apr 10 15:12:42 mhfl1 kernel: ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
> Apr 10 15:12:42 mhfl1 kernel: ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
> Apr 10 15:12:42 mhfl1 kernel: hda: QUANTUM BIGFOOT2550A, ATA DISK drive
> Apr 10 15:12:42 mhfl1 kernel: blk: queue c0347ae0, I/O limit 4095Mb (mask 0xffffffff)
> Apr 10 15:12:42 mhfl1 kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> Apr 10 15:12:43 mhfl1 kernel: hda: attached ide-disk driver.
>
> ------------------------------\/
> Apr 10 15:12:43 mhfl1 kernel: hda: task_no_data_intr: status=0x53 { DriveReady SeekComplete Index Error }
> Apr 10 15:12:43 mhfl1 kernel: hda: task_no_data_intr: error=0x04 { DriveStatusError }
>
> Apr 10 15:12:43 mhfl1 kernel: hda: 5033952 sectors (2577 MB) w/87KiB Cache, CHS=624/128/63, DMA
> Apr 10 15:12:43 mhfl1 kernel: Partition check:
> Apr 10 15:12:43 mhfl1 kernel: hda: hda1 hda2 hda3
>
> ----------
> Mar 30 15:46:51 mhfl1 kernel: Linux version 2.5.66-mhf2 (mhf@mhfl2) (gcc version 2.95.3 20010315 (release)) #12 Sat Mar 29
>
> Mar 30 15:47:05 mhfl1 kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> Mar 30 15:47:05 mhfl1 kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> Mar 30 15:47:05 mhfl1 kernel: PIIX3: IDE controller at PCI slot 00:07.1
> Mar 30 15:47:05 mhfl1 kernel: PIIX3: chipset revision 0
> Mar 30 15:47:05 mhfl1 kernel: PIIX3: not 100%% native mode: will probe irqs later
> Mar 30 15:47:05 mhfl1 kernel: ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
> Mar 30 15:47:05 mhfl1 kernel: ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
> Mar 30 15:47:05 mhfl1 kernel: hda: QUANTUM BIGFOOT2550A, ATA DISK drive
> Mar 30 15:47:05 mhfl1 kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
>
> ------------------------------\/
> Mar 30 15:47:05 mhfl1 kernel: hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
> Mar 30 15:47:05 mhfl1 kernel: hda: task_no_data_intr: error=0x04 { DriveStatusError }
>
> Mar 30 15:47:05 mhfl1 kernel: hda: 5033952 sectors (2577 MB) w/87KiB Cache, CHS=4994/16/63, DMA
> Mar 30 15:47:05 mhfl1 kernel: hda: hda1 hda2 hda3
>
> Regards
> Michael
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
Andre Hedrick
LAD Storage Consulting Group
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: 2.4.21-pre7, 2.5.66, IDE Errors during boot - just a nuisance ?
2003-04-10 8:02 ` Andre Hedrick
@ 2003-04-10 11:00 ` Rob van Nieuwkerk
0 siblings, 0 replies; 5+ messages in thread
From: Rob van Nieuwkerk @ 2003-04-10 11:00 UTC (permalink / raw)
To: Andre Hedrick; +Cc: mflt1, linux-kernel
Hi Andre,
> All it is an aborted command.
> just a nuisanse and noise maker!
OK. But can you please explain a bit more what is happening ?
Why is the command aborted ?
I get a similar error when inserting a PCMCIA CompactFlash adapter
in my RH 9 laptop (RH kernel 2.4.20-9):
hdc: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: task_no_data_intr: error=0x00 { }
Besides the kernel error the machine completely freezes for 20 seconds.
(See https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=88411 )
greetings,
Rob van Nieuwkerk
> On Thu, 10 Apr 2003, Michael Frank wrote:
>
> > Noticed this for some time in 2.5.64 and up, and now also in 2.4.21-pre6 and pre7. It was OK 2.4.20. No functional problems were encountered with 2.4.21, 2.5.6x so far.
> >
> > Its a P1, lspci follows
> >
> > 00:00.0 Host bridge: Intel Corp. 430HX - 82439HX TXC [Triton II] (rev 03)
> > 00:07.0 ISA bridge: Intel Corp. 82371SB PIIX3 ISA [Natoma/Triton II] (rev 01)
> > 00:07.1 IDE interface: Intel Corp. 82371SB PIIX3 IDE [Natoma/Triton II]
> > 00:09.0 VGA compatible controller: S3 Inc. ViRGE/DX or /GX (rev 01)
> > 00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
> > 00:0b.0 SCSI storage controller: Adaptec AHA-7850 (rev 01)
> >
> >
> > Apr 10 15:17:30 mhfl1 kernel: Linux version 2.4.21-pre7-mhf18-np (mhf@mhfl3) (gcc version 2.95.3 20010315 (release)) #2
> >
> > Apr 10 15:12:42 mhfl1 kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
> > Apr 10 15:12:42 mhfl1 kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> > Apr 10 15:12:42 mhfl1 kernel: PIIX3: IDE controller at PCI slot 00:07.1
> > Apr 10 15:12:42 mhfl1 kernel: PIIX3: chipset revision 0
> > Apr 10 15:12:42 mhfl1 kernel: PIIX3: not 100%% native mode: will probe irqs later
> > Apr 10 15:12:42 mhfl1 kernel: ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
> > Apr 10 15:12:42 mhfl1 kernel: ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
> > Apr 10 15:12:42 mhfl1 kernel: hda: QUANTUM BIGFOOT2550A, ATA DISK drive
> > Apr 10 15:12:42 mhfl1 kernel: blk: queue c0347ae0, I/O limit 4095Mb (mask 0xffffffff)
> > Apr 10 15:12:42 mhfl1 kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> > Apr 10 15:12:43 mhfl1 kernel: hda: attached ide-disk driver.
> >
> > ------------------------------\/
> > Apr 10 15:12:43 mhfl1 kernel: hda: task_no_data_intr: status=0x53 { DriveReady SeekComplete Index Error }
> > Apr 10 15:12:43 mhfl1 kernel: hda: task_no_data_intr: error=0x04 { DriveStatusError }
> >
> > Apr 10 15:12:43 mhfl1 kernel: hda: 5033952 sectors (2577 MB) w/87KiB Cache, CHS=624/128/63, DMA
> > Apr 10 15:12:43 mhfl1 kernel: Partition check:
> > Apr 10 15:12:43 mhfl1 kernel: hda: hda1 hda2 hda3
> >
> > ----------
> > Mar 30 15:46:51 mhfl1 kernel: Linux version 2.5.66-mhf2 (mhf@mhfl2) (gcc version 2.95.3 20010315 (release)) #12 Sat Mar 29
> >
> > Mar 30 15:47:05 mhfl1 kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> > Mar 30 15:47:05 mhfl1 kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> > Mar 30 15:47:05 mhfl1 kernel: PIIX3: IDE controller at PCI slot 00:07.1
> > Mar 30 15:47:05 mhfl1 kernel: PIIX3: chipset revision 0
> > Mar 30 15:47:05 mhfl1 kernel: PIIX3: not 100%% native mode: will probe irqs later
> > Mar 30 15:47:05 mhfl1 kernel: ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
> > Mar 30 15:47:05 mhfl1 kernel: ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
> > Mar 30 15:47:05 mhfl1 kernel: hda: QUANTUM BIGFOOT2550A, ATA DISK drive
> > Mar 30 15:47:05 mhfl1 kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> >
> > ------------------------------\/
> > Mar 30 15:47:05 mhfl1 kernel: hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
> > Mar 30 15:47:05 mhfl1 kernel: hda: task_no_data_intr: error=0x04 { DriveStatusError }
> >
> > Mar 30 15:47:05 mhfl1 kernel: hda: 5033952 sectors (2577 MB) w/87KiB Cache, CHS=4994/16/63, DMA
> > Mar 30 15:47:05 mhfl1 kernel: hda: hda1 hda2 hda3
> >
> > Regards
> > Michael
> >
> > -
> > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> > the body of a message to majordomo@vger.kernel.org
> > More majordomo info at http://vger.kernel.org/majordomo-info.html
> > Please read the FAQ at http://www.tux.org/lkml/
> >
>
> Andre Hedrick
> LAD Storage Consulting Group
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: 2.4.21-pre7, 2.5.66, IDE Errors during boot - just a nuisance ?
2003-04-10 7:54 2.4.21-pre7, 2.5.66, IDE Errors during boot - just a nuisance ? Michael Frank
2003-04-10 8:02 ` Andre Hedrick
@ 2003-04-11 7:39 ` Jarmo Järvenpää
2003-04-11 7:55 ` Michael Frank
1 sibling, 1 reply; 5+ messages in thread
From: Jarmo Järvenpää @ 2003-04-11 7:39 UTC (permalink / raw)
To: Michael Frank; +Cc: linux-kernel
Indeed we have the same problem.
This gives a bit of headache, hda1 and hdc1 are software raid 1 array
and sometimes one disk is dropped from the array due "error" on the
disk.
Hotadd will succeed and no bad blocks on either disk. No problems with
2.4.18. Not tested with .19 nor .20.
BR,
Jarmo
Kernel 2.4.2.21-pre6
lspci:
00:00.0 Host bridge: Intel Corp. 440LX/EX - 82443LX/EX Host bridge (rev
03)
00:01.0 PCI bridge: Intel Corp. 440LX/EX - 82443LX/EX AGP bridge (rev
03)
00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 01)
00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 01)
00:0e.0 VGA compatible controller: Matrox Graphics, Inc. MGA 2164W
[Millennium II]
00:10.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone]
(rev 30)
dmesg:
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
PIIX4: IDE controller at PCI slot 00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
hda: QUANTUM FIREBALL_TM3200A, ATA DISK drive
hdb: E295X, ATAPI CD/DVD-ROM drive
blk: queue c02e1ee0, I/O limit 4095Mb (mask 0xffffffff)
hdc: QUANTUM FIREBALL_TM3200A, ATA DISK drive
blk: queue c02e2330, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hda: task_no_data_intr: error=0x04 { DriveStatusError }
hda: 6281856 sectors (3216 MB) w/76KiB Cache, CHS=779/128/63, DMA
hdc: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: task_no_data_intr: error=0x04 { DriveStatusError }
hdc: 6281856 sectors (3216 MB) w/76KiB Cache, CHS=6232/16/63, DMA
hdb: ATAPI 16X CD-ROM drive, 240kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
Partition check:
cat /proc/ide/piix
Controller: 0
Intel PIIX4 Ultra 33 Chipset.
--------------- Primary Channel ---------------- Secondary Channel
-------------
enabled enabled
--------------- drive0 --------- drive1 -------- drive0 ----------
drive1 ------
DMA enabled: yes yes yes no
UDMA enabled: no no no no
UDMA enabled: X X X X
UDMA
DMA
PIO
hdparm -I /dev/hda
/dev/hda:
ATA device, with non-removable media
Model Number: QUANTUM FIREBALL_TM3200A
Serial Number: 295702034106
Firmware Revision: A6B.2400
Standards:
Likely used: 2
Configuration:
Logical max current
cylinders 6232 6232
heads 16 16
sectors/track 63 63
--
bytes/track: 32256 bytes/sector: 512
CHS current addressable sectors: 6281856
LBA user addressable sectors: 6281856
device size with M = 1024*1024: 3067 MBytes
device size with M = 1000*1000: 3216 MBytes (3 GB)
Capabilities:
LBA, IORDY(can be disabled)
Buffer size: 76.5kB bytes avail on r/w long: 4
Standby timer values: spec'd by Vendor
R/W multiple sector transfer: Max = 16 Current = 16
DMA: sdma0 sdma1 sdma2 mdma0 mdma1 *mdma2
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=300ns IORDY flow control=120ns
hdparm -I /dev/hdc
/dev/hdc:
ATA device, with non-removable media
Model Number: QUANTUM FIREBALL_TM3200A
Serial Number: 295634511413
Firmware Revision: A6B.2400
Standards:
Likely used: 2
Configuration:
Logical max current
cylinders 6232 6232
heads 16 16
sectors/track 63 63
--
bytes/track: 32256 bytes/sector: 512
CHS current addressable sectors: 6281856
LBA user addressable sectors: 6281856
device size with M = 1024*1024: 3067 MBytes
device size with M = 1000*1000: 3216 MBytes (3 GB)
Capabilities:
LBA, IORDY(can be disabled)
Buffer size: 76.5kB bytes avail on r/w long: 4
Standby timer values: spec'd by Vendor
R/W multiple sector transfer: Max = 16 Current = 16
DMA: sdma0 sdma1 sdma2 mdma0 mdma1 *mdma2
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=300ns IORDY flow control=120ns
Michael Frank wrote:
>
> Noticed this for some time in 2.5.64 and up, and now also in 2.4.21-pre6 and pre7. It was OK 2.4.20. No functional problems were encountered with 2.4.21, 2.5.6x so far.
>
> Its a P1, lspci follows
>
> 00:00.0 Host bridge: Intel Corp. 430HX - 82439HX TXC [Triton II] (rev 03)
> 00:07.0 ISA bridge: Intel Corp. 82371SB PIIX3 ISA [Natoma/Triton II] (rev 01)
> 00:07.1 IDE interface: Intel Corp. 82371SB PIIX3 IDE [Natoma/Triton II]
> 00:09.0 VGA compatible controller: S3 Inc. ViRGE/DX or /GX (rev 01)
> 00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
> 00:0b.0 SCSI storage controller: Adaptec AHA-7850 (rev 01)
>
> Apr 10 15:17:30 mhfl1 kernel: Linux version 2.4.21-pre7-mhf18-np (mhf@mhfl3) (gcc version 2.95.3 20010315 (release)) #2
>
> Apr 10 15:12:42 mhfl1 kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
> Apr 10 15:12:42 mhfl1 kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> Apr 10 15:12:42 mhfl1 kernel: PIIX3: IDE controller at PCI slot 00:07.1
> Apr 10 15:12:42 mhfl1 kernel: PIIX3: chipset revision 0
> Apr 10 15:12:42 mhfl1 kernel: PIIX3: not 100%% native mode: will probe irqs later
> Apr 10 15:12:42 mhfl1 kernel: ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
> Apr 10 15:12:42 mhfl1 kernel: ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
> Apr 10 15:12:42 mhfl1 kernel: hda: QUANTUM BIGFOOT2550A, ATA DISK drive
> Apr 10 15:12:42 mhfl1 kernel: blk: queue c0347ae0, I/O limit 4095Mb (mask 0xffffffff)
> Apr 10 15:12:42 mhfl1 kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> Apr 10 15:12:43 mhfl1 kernel: hda: attached ide-disk driver.
>
> ------------------------------\/
> Apr 10 15:12:43 mhfl1 kernel: hda: task_no_data_intr: status=0x53 { DriveReady SeekComplete Index Error }
> Apr 10 15:12:43 mhfl1 kernel: hda: task_no_data_intr: error=0x04 { DriveStatusError }
>
> Apr 10 15:12:43 mhfl1 kernel: hda: 5033952 sectors (2577 MB) w/87KiB Cache, CHS=624/128/63, DMA
> Apr 10 15:12:43 mhfl1 kernel: Partition check:
> Apr 10 15:12:43 mhfl1 kernel: hda: hda1 hda2 hda3
>
> ----------
> Mar 30 15:46:51 mhfl1 kernel: Linux version 2.5.66-mhf2 (mhf@mhfl2) (gcc version 2.95.3 20010315 (release)) #12 Sat Mar 29
>
> Mar 30 15:47:05 mhfl1 kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> Mar 30 15:47:05 mhfl1 kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> Mar 30 15:47:05 mhfl1 kernel: PIIX3: IDE controller at PCI slot 00:07.1
> Mar 30 15:47:05 mhfl1 kernel: PIIX3: chipset revision 0
> Mar 30 15:47:05 mhfl1 kernel: PIIX3: not 100%% native mode: will probe irqs later
> Mar 30 15:47:05 mhfl1 kernel: ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
> Mar 30 15:47:05 mhfl1 kernel: ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
> Mar 30 15:47:05 mhfl1 kernel: hda: QUANTUM BIGFOOT2550A, ATA DISK drive
> Mar 30 15:47:05 mhfl1 kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
>
> ------------------------------\/
> Mar 30 15:47:05 mhfl1 kernel: hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
> Mar 30 15:47:05 mhfl1 kernel: hda: task_no_data_intr: error=0x04 { DriveStatusError }
>
> Mar 30 15:47:05 mhfl1 kernel: hda: 5033952 sectors (2577 MB) w/87KiB Cache, CHS=4994/16/63, DMA
> Mar 30 15:47:05 mhfl1 kernel: hda: hda1 hda2 hda3
>
> Regards
> Michael
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: 2.4.21-pre7, 2.5.66, IDE Errors during boot - just a nuisance ?
2003-04-11 7:39 ` Jarmo Järvenpää
@ 2003-04-11 7:55 ` Michael Frank
0 siblings, 0 replies; 5+ messages in thread
From: Michael Frank @ 2003-04-11 7:55 UTC (permalink / raw)
To: Jarmo Järvenpää; +Cc: linux-kernel
I just brought it up because 2.4.21 is on its way and i'am not used to error messages - even "small" ones -, which werent there before being ignored.
Best Regards
Michael
On Friday 11 April 2003 15:39, Jarmo Järvenpää wrote:
> Indeed we have the same problem.
>
> This gives a bit of headache, hda1 and hdc1 are software raid 1 array
> and sometimes one disk is dropped from the array due "error" on the
> disk.
> Hotadd will succeed and no bad blocks on either disk. No problems with
> 2.4.18. Not tested with .19 nor .20.
>
>
> BR,
> Jarmo
>
>
> Kernel 2.4.2.21-pre6
>
> lspci:
> 00:00.0 Host bridge: Intel Corp. 440LX/EX - 82443LX/EX Host bridge (rev
> 03)
> 00:01.0 PCI bridge: Intel Corp. 440LX/EX - 82443LX/EX AGP bridge (rev
> 03)
> 00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 01)
> 00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
> 00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
> 00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 01)
> 00:0e.0 VGA compatible controller: Matrox Graphics, Inc. MGA 2164W
> [Millennium II]
> 00:10.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone]
> (rev 30)
>
>
> dmesg:
> ide: Assuming 33MHz system bus speed for PIO modes; override with
> idebus=xx
> PIIX4: IDE controller at PCI slot 00:07.1
> PIIX4: chipset revision 1
> PIIX4: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
> ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
> hda: QUANTUM FIREBALL_TM3200A, ATA DISK drive
> hdb: E295X, ATAPI CD/DVD-ROM drive
> blk: queue c02e1ee0, I/O limit 4095Mb (mask 0xffffffff)
> hdc: QUANTUM FIREBALL_TM3200A, ATA DISK drive
> blk: queue c02e2330, I/O limit 4095Mb (mask 0xffffffff)
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> ide1 at 0x170-0x177,0x376 on irq 15
> hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
> hda: task_no_data_intr: error=0x04 { DriveStatusError }
> hda: 6281856 sectors (3216 MB) w/76KiB Cache, CHS=779/128/63, DMA
> hdc: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
> hdc: task_no_data_intr: error=0x04 { DriveStatusError }
> hdc: 6281856 sectors (3216 MB) w/76KiB Cache, CHS=6232/16/63, DMA
> hdb: ATAPI 16X CD-ROM drive, 240kB Cache, DMA
> Uniform CD-ROM driver Revision: 3.12
> Partition check:
>
>
> cat /proc/ide/piix
> Controller: 0
>
> Intel PIIX4 Ultra 33 Chipset.
> --------------- Primary Channel ---------------- Secondary Channel
> -------------
> enabled enabled
> --------------- drive0 --------- drive1 -------- drive0 ----------
> drive1 ------
> DMA enabled: yes yes yes no
> UDMA enabled: no no no no
> UDMA enabled: X X X X
> UDMA
> DMA
> PIO
>
>
> hdparm -I /dev/hda
> /dev/hda:
>
> ATA device, with non-removable media
> Model Number: QUANTUM FIREBALL_TM3200A
> Serial Number: 295702034106
> Firmware Revision: A6B.2400
> Standards:
> Likely used: 2
> Configuration:
> Logical max current
> cylinders 6232 6232
> heads 16 16
> sectors/track 63 63
> --
> bytes/track: 32256 bytes/sector: 512
> CHS current addressable sectors: 6281856
> LBA user addressable sectors: 6281856
> device size with M = 1024*1024: 3067 MBytes
> device size with M = 1000*1000: 3216 MBytes (3 GB)
> Capabilities:
> LBA, IORDY(can be disabled)
> Buffer size: 76.5kB bytes avail on r/w long: 4
> Standby timer values: spec'd by Vendor
> R/W multiple sector transfer: Max = 16 Current = 16
> DMA: sdma0 sdma1 sdma2 mdma0 mdma1 *mdma2
> Cycle time: min=120ns recommended=120ns
> PIO: pio0 pio1 pio2 pio3 pio4
> Cycle time: no flow control=300ns IORDY flow control=120ns
>
> hdparm -I /dev/hdc
> /dev/hdc:
>
> ATA device, with non-removable media
> Model Number: QUANTUM FIREBALL_TM3200A
> Serial Number: 295634511413
> Firmware Revision: A6B.2400
> Standards:
> Likely used: 2
> Configuration:
> Logical max current
> cylinders 6232 6232
> heads 16 16
> sectors/track 63 63
> --
> bytes/track: 32256 bytes/sector: 512
> CHS current addressable sectors: 6281856
> LBA user addressable sectors: 6281856
> device size with M = 1024*1024: 3067 MBytes
> device size with M = 1000*1000: 3216 MBytes (3 GB)
> Capabilities:
> LBA, IORDY(can be disabled)
> Buffer size: 76.5kB bytes avail on r/w long: 4
> Standby timer values: spec'd by Vendor
> R/W multiple sector transfer: Max = 16 Current = 16
> DMA: sdma0 sdma1 sdma2 mdma0 mdma1 *mdma2
> Cycle time: min=120ns recommended=120ns
> PIO: pio0 pio1 pio2 pio3 pio4
> Cycle time: no flow control=300ns IORDY flow control=120ns
>
> Michael Frank wrote:
> > Noticed this for some time in 2.5.64 and up, and now also in 2.4.21-pre6
> > and pre7. It was OK 2.4.20. No functional problems were encountered with
> > 2.4.21, 2.5.6x so far.
> >
> > Its a P1, lspci follows
> >
> > 00:00.0 Host bridge: Intel Corp. 430HX - 82439HX TXC [Triton II] (rev 03)
> > 00:07.0 ISA bridge: Intel Corp. 82371SB PIIX3 ISA [Natoma/Triton II] (rev
> > 01) 00:07.1 IDE interface: Intel Corp. 82371SB PIIX3 IDE [Natoma/Triton
> > II] 00:09.0 VGA compatible controller: S3 Inc. ViRGE/DX or /GX (rev 01)
> > 00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
> > RTL-8139/8139C/8139C+ (rev 10) 00:0b.0 SCSI storage controller: Adaptec
> > AHA-7850 (rev 01)
> >
> > Apr 10 15:17:30 mhfl1 kernel: Linux version 2.4.21-pre7-mhf18-np
> > (mhf@mhfl3) (gcc version 2.95.3 20010315 (release)) #2
> >
> > Apr 10 15:12:42 mhfl1 kernel: Uniform Multi-Platform E-IDE driver
> > Revision: 7.00beta-2.4 Apr 10 15:12:42 mhfl1 kernel: ide: Assuming 33MHz
> > system bus speed for PIO modes; override with idebus=xx Apr 10 15:12:42
> > mhfl1 kernel: PIIX3: IDE controller at PCI slot 00:07.1 Apr 10 15:12:42
> > mhfl1 kernel: PIIX3: chipset revision 0
> > Apr 10 15:12:42 mhfl1 kernel: PIIX3: not 100%% native mode: will probe
> > irqs later Apr 10 15:12:42 mhfl1 kernel: ide0: BM-DMA at
> > 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio Apr 10 15:12:42 mhfl1
> > kernel: ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio,
> > hdd:pio Apr 10 15:12:42 mhfl1 kernel: hda: QUANTUM BIGFOOT2550A, ATA DISK
> > drive Apr 10 15:12:42 mhfl1 kernel: blk: queue c0347ae0, I/O limit 4095Mb
> > (mask 0xffffffff) Apr 10 15:12:42 mhfl1 kernel: ide0 at 0x1f0-0x1f7,0x3f6
> > on irq 14 Apr 10 15:12:43 mhfl1 kernel: hda: attached ide-disk driver.
> >
> > ------------------------------\/
> > Apr 10 15:12:43 mhfl1 kernel: hda: task_no_data_intr: status=0x53 {
> > DriveReady SeekComplete Index Error } Apr 10 15:12:43 mhfl1 kernel: hda:
> > task_no_data_intr: error=0x04 { DriveStatusError }
> >
> > Apr 10 15:12:43 mhfl1 kernel: hda: 5033952 sectors (2577 MB) w/87KiB
> > Cache, CHS=624/128/63, DMA Apr 10 15:12:43 mhfl1 kernel: Partition check:
> > Apr 10 15:12:43 mhfl1 kernel: hda: hda1 hda2 hda3
> >
> > ----------
> > Mar 30 15:46:51 mhfl1 kernel: Linux version 2.5.66-mhf2 (mhf@mhfl2) (gcc
> > version 2.95.3 20010315 (release)) #12 Sat Mar 29
> >
> > Mar 30 15:47:05 mhfl1 kernel: Uniform Multi-Platform E-IDE driver
> > Revision: 7.00alpha2 Mar 30 15:47:05 mhfl1 kernel: ide: Assuming 33MHz
> > system bus speed for PIO modes; override with idebus=xx Mar 30 15:47:05
> > mhfl1 kernel: PIIX3: IDE controller at PCI slot 00:07.1 Mar 30 15:47:05
> > mhfl1 kernel: PIIX3: chipset revision 0
> > Mar 30 15:47:05 mhfl1 kernel: PIIX3: not 100%% native mode: will probe
> > irqs later Mar 30 15:47:05 mhfl1 kernel: ide0: BM-DMA at
> > 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio Mar 30 15:47:05 mhfl1
> > kernel: ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio,
> > hdd:pio Mar 30 15:47:05 mhfl1 kernel: hda: QUANTUM BIGFOOT2550A, ATA DISK
> > drive Mar 30 15:47:05 mhfl1 kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> >
> > ------------------------------\/
> > Mar 30 15:47:05 mhfl1 kernel: hda: task_no_data_intr: status=0x51 {
> > DriveReady SeekComplete Error } Mar 30 15:47:05 mhfl1 kernel: hda:
> > task_no_data_intr: error=0x04 { DriveStatusError }
> >
> > Mar 30 15:47:05 mhfl1 kernel: hda: 5033952 sectors (2577 MB) w/87KiB
> > Cache, CHS=4994/16/63, DMA Mar 30 15:47:05 mhfl1 kernel: hda: hda1 hda2
> > hda3
> >
> > Regards
> > Michael
> >
> > -
> > To unsubscribe from this list: send the line "unsubscribe linux-kernel"
> > in the body of a message to majordomo@vger.kernel.org
> > More majordomo info at http://vger.kernel.org/majordomo-info.html
> > Please read the FAQ at http://www.tux.org/lkml/
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2003-04-11 7:44 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2003-04-10 7:54 2.4.21-pre7, 2.5.66, IDE Errors during boot - just a nuisance ? Michael Frank
2003-04-10 8:02 ` Andre Hedrick
2003-04-10 11:00 ` Rob van Nieuwkerk
2003-04-11 7:39 ` Jarmo Järvenpää
2003-04-11 7:55 ` Michael Frank
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).