[PATCH/RESEND 00/12] Convert MSM to common clock framework

[PATCH/RESEND 00/12] Convert MSM to common clock framework

[Stephen Boyd]

Resending to collect higher level maintainer acks per Olof's request. 
The plan is to push this patchset through MSM to the arm-soc tree.

This patchset moves the existing MSM clock code and affected drivers to the
common clock framework. A prerequisite of moving to the common clock
framework is to use clk_prepare() and clk_enable() so the first
few patches migrate drivers to that call (clk_prepare() is a no-op on MSM
right now). It also removes some custom clock APIs that MSM provides
and finally moves the proc_comm clock code to the common struct clk.

This patch series will be used as the foundation of the MSM 8660/8960
clock code that I plan to send out after this series.

Stephen Boyd (12):
  msm_serial: Convert to clk_prepare/unprepare
  msm_serial: Use devm_clk_get() and properly return errors
  usb: otg: msm: Convert to clk_prepare/unprepare
  msm_sdcc: Convert to clk_prepare/unprepare
  msm: iommu: Convert to clk_prepare/unprepare
  msm: iommu: Use clk_set_rate() instead of clk_set_min_rate()
  ARM: msm: Remove custom clk_set_flags() API
  ARM: msm: Remove custom clk_set_{max,min}_rate() API
  ARM: msm: Remove clock-7x30.h include file
  ARM: msm: Prepare clk_get() users in mach-msm for clock-pcom driver
  ARM: msm: Make proc_comm clock control into a platform driver
  ARM: msm: Migrate to common clock framework

 arch/arm/Kconfig                       |   2 +-
 arch/arm/mach-msm/Makefile             |  10 +-
 arch/arm/mach-msm/board-halibut.c      |   2 +-
 arch/arm/mach-msm/board-msm7x30.c      |   2 +-
 arch/arm/mach-msm/board-qsd8x50.c      |   2 +-
 arch/arm/mach-msm/board-trout-panel.c  |  19 ++--
 arch/arm/mach-msm/board-trout.c        |   3 +-
 arch/arm/mach-msm/clock-7x30.h         | 155 ------------------------------
 arch/arm/mach-msm/clock-debug.c        | 130 --------------------------
 arch/arm/mach-msm/clock-pcom.c         | 149 ++++++++++++++++++-----------
 arch/arm/mach-msm/clock-pcom.h         |  31 +++---
 arch/arm/mach-msm/clock.c              | 166 +--------------------------------
 arch/arm/mach-msm/clock.h              |  51 +++-------
 arch/arm/mach-msm/devices-msm7x00.c    |  12 ++-
 arch/arm/mach-msm/devices-msm7x30.c    |  14 ++-
 arch/arm/mach-msm/devices-qsd8x50.c    |  11 ++-
 arch/arm/mach-msm/devices.h            |  15 +--
 arch/arm/mach-msm/dma.c                |   5 +-
 arch/arm/mach-msm/include/mach/board.h |   5 -
 arch/arm/mach-msm/include/mach/clk.h   |   9 --
 drivers/iommu/msm_iommu_dev.c          |  20 ++--
 drivers/mmc/host/msm_sdcc.c            |  14 ++-
 drivers/tty/serial/msm_serial.c        |  35 +++----
 drivers/usb/phy/phy-msm-usb.c          |  38 ++++----
 24 files changed, 241 insertions(+), 659 deletions(-)
 delete mode 100644 arch/arm/mach-msm/clock-7x30.h
 delete mode 100644 arch/arm/mach-msm/clock-debug.c

-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation

[PATCH/RESEND 01/12] msm_serial: Convert to clk_prepare/unprepare

[Stephen Boyd]

Add calls to clk_prepare and unprepare so that MSM can migrate to
the common clock framework.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
 drivers/tty/serial/msm_serial.c | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)

diff --git a/drivers/tty/serial/msm_serial.c b/drivers/tty/serial/msm_serial.c
index b11e997..0149603 100644
--- a/drivers/tty/serial/msm_serial.c
+++ b/drivers/tty/serial/msm_serial.c
@@ -408,9 +408,9 @@ static void msm_init_clock(struct uart_port *port)
 {
 	struct msm_port *msm_port = UART_TO_MSM(port);
 
-	clk_enable(msm_port->clk);
+	clk_prepare_enable(msm_port->clk);
 	if (!IS_ERR(msm_port->pclk))
-		clk_enable(msm_port->pclk);
+		clk_prepare_enable(msm_port->pclk);
 	msm_serial_set_mnd_regs(port);
 }
 
@@ -486,7 +486,7 @@ static void msm_shutdown(struct uart_port *port)
 	msm_port->imr = 0;
 	msm_write(port, 0, UART_IMR); /* disable interrupts */
 
-	clk_disable(msm_port->clk);
+	clk_disable_unprepare(msm_port->clk);
 
 	free_irq(port->irq, port);
 }
@@ -688,14 +688,14 @@ static void msm_power(struct uart_port *port, unsigned int state,
 
 	switch (state) {
 	case 0:
-		clk_enable(msm_port->clk);
+		clk_prepare_enable(msm_port->clk);
 		if (!IS_ERR(msm_port->pclk))
-			clk_enable(msm_port->pclk);
+			clk_prepare_enable(msm_port->pclk);
 		break;
 	case 3:
-		clk_disable(msm_port->clk);
+		clk_disable_unprepare(msm_port->clk);
 		if (!IS_ERR(msm_port->pclk))
-			clk_disable(msm_port->pclk);
+			clk_disable_unprepare(msm_port->pclk);
 		break;
 	default:
 		printk(KERN_ERR "msm_serial: Unknown PM state %d\n", state);
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation

Re: [PATCH/RESEND 01/12] msm_serial: Convert to clk_prepare/unprepare

[Greg Kroah-Hartman]

On Mon, Jun 17, 2013 at 10:43:08AM -0700, Stephen Boyd wrote:
> Add calls to clk_prepare and unprepare so that MSM can migrate to
> the common clock framework.
> 
> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Or do you want me to take the serial ones through my tree?  It's your
choice, either is fine for me.

thanks,

greg k-h

Re: [PATCH/RESEND 01/12] msm_serial: Convert to clk_prepare/unprepare

[David Brown]

On Mon, Jun 17, 2013 at 10:55:10AM -0700, Greg Kroah-Hartman wrote:
>On Mon, Jun 17, 2013 at 10:43:08AM -0700, Stephen Boyd wrote:
>> Add calls to clk_prepare and unprepare so that MSM can migrate to
>> the common clock framework.
>>
>> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
>> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
>
>Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
>
>Or do you want me to take the serial ones through my tree?  It's your
>choice, either is fine for me.

I can go ahead and pull them through the MSM tree.

Thanks,
David

-- 
sent by an employee of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation

Re: [PATCH/RESEND 01/12] msm_serial: Convert to clk_prepare/unprepare

[Greg Kroah-Hartman]

On Mon, Jun 17, 2013 at 11:07:28AM -0700, David Brown wrote:
> On Mon, Jun 17, 2013 at 10:55:10AM -0700, Greg Kroah-Hartman wrote:
> >On Mon, Jun 17, 2013 at 10:43:08AM -0700, Stephen Boyd wrote:
> >>Add calls to clk_prepare and unprepare so that MSM can migrate to
> >>the common clock framework.
> >>
> >>Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> >>Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
> >
> >Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> >
> >Or do you want me to take the serial ones through my tree?  It's your
> >choice, either is fine for me.
> 
> I can go ahead and pull them through the MSM tree.

Please do, thanks.

greg k-h

[PATCH/RESEND 02/12] msm_serial: Use devm_clk_get() and properly return errors

[Stephen Boyd]

Clocks are not clk_put() in this driver's error paths during
probe. The code that checks for clock errors also fails to
properly return the error code from the pclk member if it turns
out to be the failing clock, leading to potentially confusing
error values if the clk member is not an error pointer. Fix these
problems with devm_clk_get() and proper error checking.

Removing the clk_put() in msm_serial_remove() also points out
that msm_port is unused. Furthermore, msm_port is the wrong type
and so the clk_put() would be using the wrong pointer. Replace it
with the proper type and call uart_remove_one_port() to do the
proper cleanup.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
 drivers/tty/serial/msm_serial.c | 21 ++++++++++++---------
 1 file changed, 12 insertions(+), 9 deletions(-)

diff --git a/drivers/tty/serial/msm_serial.c b/drivers/tty/serial/msm_serial.c
index 0149603..2c6cfb3 100644
--- a/drivers/tty/serial/msm_serial.c
+++ b/drivers/tty/serial/msm_serial.c
@@ -884,19 +884,22 @@ static int __init msm_serial_probe(struct platform_device *pdev)
 		msm_port->is_uartdm = 0;
 
 	if (msm_port->is_uartdm) {
-		msm_port->clk = clk_get(&pdev->dev, "gsbi_uart_clk");
-		msm_port->pclk = clk_get(&pdev->dev, "gsbi_pclk");
+		msm_port->clk = devm_clk_get(&pdev->dev, "gsbi_uart_clk");
+		msm_port->pclk = devm_clk_get(&pdev->dev, "gsbi_pclk");
 	} else {
-		msm_port->clk = clk_get(&pdev->dev, "uart_clk");
+		msm_port->clk = devm_clk_get(&pdev->dev, "uart_clk");
 		msm_port->pclk = ERR_PTR(-ENOENT);
 	}
 
-	if (unlikely(IS_ERR(msm_port->clk) || (IS_ERR(msm_port->pclk) &&
-					       msm_port->is_uartdm)))
-			return PTR_ERR(msm_port->clk);
+	if (IS_ERR(msm_port->clk))
+		return PTR_ERR(msm_port->clk);
+
+	if (msm_port->is_uartdm) {
+		if (IS_ERR(msm_port->pclk))
+			return PTR_ERR(msm_port->pclk);
 
-	if (msm_port->is_uartdm)
 		clk_set_rate(msm_port->clk, 1843200);
+	}
 
 	port->uartclk = clk_get_rate(msm_port->clk);
 	printk(KERN_INFO "uartclk = %d\n", port->uartclk);
@@ -919,9 +922,9 @@ static int __init msm_serial_probe(struct platform_device *pdev)
 
 static int msm_serial_remove(struct platform_device *pdev)
 {
-	struct msm_port *msm_port = platform_get_drvdata(pdev);
+	struct uart_port *port = platform_get_drvdata(pdev);
 
-	clk_put(msm_port->clk);
+	uart_remove_one_port(&msm_uart_driver, port);
 
 	return 0;
 }
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation

Re: [PATCH/RESEND 02/12] msm_serial: Use devm_clk_get() and properly return errors

[Greg Kroah-Hartman]

On Mon, Jun 17, 2013 at 10:43:09AM -0700, Stephen Boyd wrote:
> Clocks are not clk_put() in this driver's error paths during
> probe. The code that checks for clock errors also fails to
> properly return the error code from the pclk member if it turns
> out to be the failing clock, leading to potentially confusing
> error values if the clk member is not an error pointer. Fix these
> problems with devm_clk_get() and proper error checking.
> 
> Removing the clk_put() in msm_serial_remove() also points out
> that msm_port is unused. Furthermore, msm_port is the wrong type
> and so the clk_put() would be using the wrong pointer. Replace it
> with the proper type and call uart_remove_one_port() to do the
> proper cleanup.
> 
> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[PATCH/RESEND 03/12] usb: otg: msm: Convert to clk_prepare/unprepare

[Stephen Boyd]

Add calls to clk_prepare and unprepare so that MSM can migrate to
the common clock framework.

Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
 drivers/usb/phy/phy-msm-usb.c | 38 +++++++++++++++++++-------------------
 1 file changed, 19 insertions(+), 19 deletions(-)

diff --git a/drivers/usb/phy/phy-msm-usb.c b/drivers/usb/phy/phy-msm-usb.c
index 749fbf4..d08f334 100644
--- a/drivers/usb/phy/phy-msm-usb.c
+++ b/drivers/usb/phy/phy-msm-usb.c
@@ -514,13 +514,13 @@ static int msm_otg_suspend(struct msm_otg *motg)
 			motg->pdata->otg_control == OTG_PMIC_CONTROL)
 		writel(readl(USB_PHY_CTRL) | PHY_RETEN, USB_PHY_CTRL);
 
-	clk_disable(motg->pclk);
-	clk_disable(motg->clk);
+	clk_disable_unprepare(motg->pclk);
+	clk_disable_unprepare(motg->clk);
 	if (motg->core_clk)
-		clk_disable(motg->core_clk);
+		clk_disable_unprepare(motg->core_clk);
 
 	if (!IS_ERR(motg->pclk_src))
-		clk_disable(motg->pclk_src);
+		clk_disable_unprepare(motg->pclk_src);
 
 	if (motg->pdata->phy_type == SNPS_28NM_INTEGRATED_PHY &&
 			motg->pdata->otg_control == OTG_PMIC_CONTROL) {
@@ -552,12 +552,12 @@ static int msm_otg_resume(struct msm_otg *motg)
 		return 0;
 
 	if (!IS_ERR(motg->pclk_src))
-		clk_enable(motg->pclk_src);
+		clk_prepare_enable(motg->pclk_src);
 
-	clk_enable(motg->pclk);
-	clk_enable(motg->clk);
+	clk_prepare_enable(motg->pclk);
+	clk_prepare_enable(motg->clk);
 	if (motg->core_clk)
-		clk_enable(motg->core_clk);
+		clk_prepare_enable(motg->core_clk);
 
 	if (motg->pdata->phy_type == SNPS_28NM_INTEGRATED_PHY &&
 			motg->pdata->otg_control == OTG_PMIC_CONTROL) {
@@ -1468,7 +1468,7 @@ static int __init msm_otg_probe(struct platform_device *pdev)
 		if (IS_ERR(motg->pclk_src))
 			goto put_clk;
 		clk_set_rate(motg->pclk_src, INT_MAX);
-		clk_enable(motg->pclk_src);
+		clk_prepare_enable(motg->pclk_src);
 	} else
 		motg->pclk_src = ERR_PTR(-ENOENT);
 
@@ -1511,8 +1511,8 @@ static int __init msm_otg_probe(struct platform_device *pdev)
 		goto free_regs;
 	}
 
-	clk_enable(motg->clk);
-	clk_enable(motg->pclk);
+	clk_prepare_enable(motg->clk);
+	clk_prepare_enable(motg->pclk);
 
 	ret = msm_hsusb_init_vddcx(motg, 1);
 	if (ret) {
@@ -1532,7 +1532,7 @@ static int __init msm_otg_probe(struct platform_device *pdev)
 	}
 
 	if (motg->core_clk)
-		clk_enable(motg->core_clk);
+		clk_prepare_enable(motg->core_clk);
 
 	writel(0, USB_USBINTR);
 	writel(0, USB_OTGSC);
@@ -1579,8 +1579,8 @@ static int __init msm_otg_probe(struct platform_device *pdev)
 free_irq:
 	free_irq(motg->irq, motg);
 disable_clks:
-	clk_disable(motg->pclk);
-	clk_disable(motg->clk);
+	clk_disable_unprepare(motg->pclk);
+	clk_disable_unprepare(motg->clk);
 ldo_exit:
 	msm_hsusb_ldo_init(motg, 0);
 vddcx_exit:
@@ -1593,7 +1593,7 @@ put_core_clk:
 	clk_put(motg->pclk);
 put_pclk_src:
 	if (!IS_ERR(motg->pclk_src)) {
-		clk_disable(motg->pclk_src);
+		clk_disable_unprepare(motg->pclk_src);
 		clk_put(motg->pclk_src);
 	}
 put_clk:
@@ -1643,12 +1643,12 @@ static int msm_otg_remove(struct platform_device *pdev)
 	if (cnt >= PHY_SUSPEND_TIMEOUT_USEC)
 		dev_err(phy->dev, "Unable to suspend PHY\n");
 
-	clk_disable(motg->pclk);
-	clk_disable(motg->clk);
+	clk_disable_unprepare(motg->pclk);
+	clk_disable_unprepare(motg->clk);
 	if (motg->core_clk)
-		clk_disable(motg->core_clk);
+		clk_disable_unprepare(motg->core_clk);
 	if (!IS_ERR(motg->pclk_src)) {
-		clk_disable(motg->pclk_src);
+		clk_disable_unprepare(motg->pclk_src);
 		clk_put(motg->pclk_src);
 	}
 	msm_hsusb_ldo_init(motg, 0);
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation

[PATCH/RESEND 04/12] msm_sdcc: Convert to clk_prepare/unprepare

[Stephen Boyd]

Add calls to clk_prepare and unprepare so that MSM can migrate to
the common clock framework.

Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
 drivers/mmc/host/msm_sdcc.c | 14 +++++++++++++-
 1 file changed, 13 insertions(+), 1 deletion(-)

diff --git a/drivers/mmc/host/msm_sdcc.c b/drivers/mmc/host/msm_sdcc.c
index 0ee4a57..b900de4 100644
--- a/drivers/mmc/host/msm_sdcc.c
+++ b/drivers/mmc/host/msm_sdcc.c
@@ -1268,10 +1268,18 @@ msmsdcc_probe(struct platform_device *pdev)
 		goto clk_put;
 	}
 
+	ret = clk_prepare(host->pclk);
+	if (ret)
+		goto clk_put;
+
+	ret = clk_prepare(host->clk);
+	if (ret)
+		goto clk_unprepare_p;
+
 	/* Enable clocks */
 	ret = msmsdcc_enable_clocks(host);
 	if (ret)
-		goto clk_put;
+		goto clk_unprepare;
 
 	host->pclk_rate = clk_get_rate(host->pclk);
 	host->clk_rate = clk_get_rate(host->clk);
@@ -1386,6 +1394,10 @@ msmsdcc_probe(struct platform_device *pdev)
 		free_irq(host->stat_irq, host);
  clk_disable:
 	msmsdcc_disable_clocks(host, 0);
+ clk_unprepare:
+	clk_unprepare(host->clk);
+ clk_unprepare_p:
+	clk_unprepare(host->pclk);
  clk_put:
 	clk_put(host->clk);
  pclk_put:
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation

[PATCH/RESEND 05/12] msm: iommu: Convert to clk_prepare/unprepare

[Stephen Boyd]

Add calls to clk_prepare and unprepare so that MSM can migrate to
the common clock framework. We never unprepare the clocks until
driver remove because the clocks are enabled and disabled in irq
context. Finer grained power management is possible in the future
via runtime power management techniques.

Cc: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
 drivers/iommu/msm_iommu_dev.c | 17 ++++++++++-------
 1 file changed, 10 insertions(+), 7 deletions(-)

diff --git a/drivers/iommu/msm_iommu_dev.c b/drivers/iommu/msm_iommu_dev.c
index 8e8fb07..d344f6a 100644
--- a/drivers/iommu/msm_iommu_dev.c
+++ b/drivers/iommu/msm_iommu_dev.c
@@ -160,7 +160,7 @@ static int msm_iommu_probe(struct platform_device *pdev)
 		goto fail;
 	}
 
-	ret = clk_enable(iommu_pclk);
+	ret = clk_prepare_enable(iommu_pclk);
 	if (ret)
 		goto fail_enable;
 
@@ -170,7 +170,7 @@ static int msm_iommu_probe(struct platform_device *pdev)
 		if (clk_get_rate(iommu_clk) == 0)
 			clk_set_min_rate(iommu_clk, 1);
 
-		ret = clk_enable(iommu_clk);
+		ret = clk_prepare_enable(iommu_clk);
 		if (ret) {
 			clk_put(iommu_clk);
 			goto fail_pclk;
@@ -261,7 +261,7 @@ fail_clk:
 		clk_put(iommu_clk);
 	}
 fail_pclk:
-	clk_disable(iommu_pclk);
+	clk_disable_unprepare(iommu_pclk);
 fail_enable:
 	clk_put(iommu_pclk);
 fail:
@@ -275,8 +275,11 @@ static int msm_iommu_remove(struct platform_device *pdev)
 
 	drv = platform_get_drvdata(pdev);
 	if (drv) {
-		if (drv->clk)
+		if (drv->clk) {
+			clk_unprepare(drv->clk);
 			clk_put(drv->clk);
+		}
+		clk_unprepare(drv->pclk);
 		clk_put(drv->pclk);
 		memset(drv, 0, sizeof(*drv));
 		kfree(drv);
@@ -314,14 +317,14 @@ static int msm_iommu_ctx_probe(struct platform_device *pdev)
 	INIT_LIST_HEAD(&ctx_drvdata->attached_elm);
 	platform_set_drvdata(pdev, ctx_drvdata);
 
-	ret = clk_enable(drvdata->pclk);
+	ret = clk_prepare_enable(drvdata->pclk);
 	if (ret)
 		goto fail;
 
 	if (drvdata->clk) {
-		ret = clk_enable(drvdata->clk);
+		ret = clk_prepare_enable(drvdata->clk);
 		if (ret) {
-			clk_disable(drvdata->pclk);
+			clk_disable_unprepare(drvdata->pclk);
 			goto fail;
 		}
 	}
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation

Re: [PATCH/RESEND 05/12] msm: iommu: Convert to clk_prepare/unprepare

[Stephen Boyd]

Sending to correct Joerg address.

On 06/17, Stephen Boyd wrote:
> Add calls to clk_prepare and unprepare so that MSM can migrate to
> the common clock framework. We never unprepare the clocks until
> driver remove because the clocks are enabled and disabled in irq
> context. Finer grained power management is possible in the future
> via runtime power management techniques.
> 
> Cc: Joerg Roedel <joerg.roedel@amd.com>
> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
> ---
>  drivers/iommu/msm_iommu_dev.c | 17 ++++++++++-------
>  1 file changed, 10 insertions(+), 7 deletions(-)
> 
> diff --git a/drivers/iommu/msm_iommu_dev.c b/drivers/iommu/msm_iommu_dev.c
> index 8e8fb07..d344f6a 100644
> --- a/drivers/iommu/msm_iommu_dev.c
> +++ b/drivers/iommu/msm_iommu_dev.c
> @@ -160,7 +160,7 @@ static int msm_iommu_probe(struct platform_device *pdev)
>  		goto fail;
>  	}
>  
> -	ret = clk_enable(iommu_pclk);
> +	ret = clk_prepare_enable(iommu_pclk);
>  	if (ret)
>  		goto fail_enable;
>  
> @@ -170,7 +170,7 @@ static int msm_iommu_probe(struct platform_device *pdev)
>  		if (clk_get_rate(iommu_clk) == 0)
>  			clk_set_min_rate(iommu_clk, 1);
>  
> -		ret = clk_enable(iommu_clk);
> +		ret = clk_prepare_enable(iommu_clk);
>  		if (ret) {
>  			clk_put(iommu_clk);
>  			goto fail_pclk;
> @@ -261,7 +261,7 @@ fail_clk:
>  		clk_put(iommu_clk);
>  	}
>  fail_pclk:
> -	clk_disable(iommu_pclk);
> +	clk_disable_unprepare(iommu_pclk);
>  fail_enable:
>  	clk_put(iommu_pclk);
>  fail:
> @@ -275,8 +275,11 @@ static int msm_iommu_remove(struct platform_device *pdev)
>  
>  	drv = platform_get_drvdata(pdev);
>  	if (drv) {
> -		if (drv->clk)
> +		if (drv->clk) {
> +			clk_unprepare(drv->clk);
>  			clk_put(drv->clk);
> +		}
> +		clk_unprepare(drv->pclk);
>  		clk_put(drv->pclk);
>  		memset(drv, 0, sizeof(*drv));
>  		kfree(drv);
> @@ -314,14 +317,14 @@ static int msm_iommu_ctx_probe(struct platform_device *pdev)
>  	INIT_LIST_HEAD(&ctx_drvdata->attached_elm);
>  	platform_set_drvdata(pdev, ctx_drvdata);
>  
> -	ret = clk_enable(drvdata->pclk);
> +	ret = clk_prepare_enable(drvdata->pclk);
>  	if (ret)
>  		goto fail;
>  
>  	if (drvdata->clk) {
> -		ret = clk_enable(drvdata->clk);
> +		ret = clk_prepare_enable(drvdata->clk);
>  		if (ret) {
> -			clk_disable(drvdata->pclk);
> +			clk_disable_unprepare(drvdata->pclk);
>  			goto fail;
>  		}
>  	}
> -- 
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> hosted by The Linux Foundation
> 
> --
> To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html

-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation

Re: [PATCH/RESEND 05/12] msm: iommu: Convert to clk_prepare/unprepare

[Joerg Roedel]

On Thu, Jun 20, 2013 at 09:40:51AM -0700, Stephen Boyd wrote:
> Sending to correct Joerg address.
> 
> On 06/17, Stephen Boyd wrote:
> > Add calls to clk_prepare and unprepare so that MSM can migrate to
> > the common clock framework. We never unprepare the clocks until
> > driver remove because the clocks are enabled and disabled in irq
> > context. Finer grained power management is possible in the future
> > via runtime power management techniques.
> > 
> > Cc: Joerg Roedel <joerg.roedel@amd.com>
> > Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Acked-by: Joerg Roedel <joro@8bytes.org>

[PATCH/RESEND 06/12] msm: iommu: Use clk_set_rate() instead of clk_set_min_rate()

[Stephen Boyd]

Calling clk_set_min_rate() is no better than just calling
clk_set_rate() because MSM clock code already takes care of
calling the min_rate ops if the clock really needs
clk_set_min_rate() called on it.

Cc: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
 drivers/iommu/msm_iommu_dev.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/drivers/iommu/msm_iommu_dev.c b/drivers/iommu/msm_iommu_dev.c
index d344f6a..9144a6b 100644
--- a/drivers/iommu/msm_iommu_dev.c
+++ b/drivers/iommu/msm_iommu_dev.c
@@ -29,7 +29,6 @@
 
 #include <mach/iommu_hw-8xxx.h>
 #include <mach/iommu.h>
-#include <mach/clk.h>
 
 struct iommu_ctx_iter_data {
 	/* input */
@@ -168,7 +167,7 @@ static int msm_iommu_probe(struct platform_device *pdev)
 
 	if (!IS_ERR(iommu_clk))	{
 		if (clk_get_rate(iommu_clk) == 0)
-			clk_set_min_rate(iommu_clk, 1);
+			clk_set_rate(iommu_clk, 1);
 
 		ret = clk_prepare_enable(iommu_clk);
 		if (ret) {
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation

Re: [PATCH/RESEND 06/12] msm: iommu: Use clk_set_rate() instead of clk_set_min_rate()

[Stephen Boyd]

Sending to correct Joerg address.

On 06/17, Stephen Boyd wrote:
> Calling clk_set_min_rate() is no better than just calling
> clk_set_rate() because MSM clock code already takes care of
> calling the min_rate ops if the clock really needs
> clk_set_min_rate() called on it.
> 
> Cc: Joerg Roedel <joerg.roedel@amd.com>
> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
> ---
>  drivers/iommu/msm_iommu_dev.c | 3 +--
>  1 file changed, 1 insertion(+), 2 deletions(-)
> 
> diff --git a/drivers/iommu/msm_iommu_dev.c b/drivers/iommu/msm_iommu_dev.c
> index d344f6a..9144a6b 100644
> --- a/drivers/iommu/msm_iommu_dev.c
> +++ b/drivers/iommu/msm_iommu_dev.c
> @@ -29,7 +29,6 @@
>  
>  #include <mach/iommu_hw-8xxx.h>
>  #include <mach/iommu.h>
> -#include <mach/clk.h>
>  
>  struct iommu_ctx_iter_data {
>  	/* input */
> @@ -168,7 +167,7 @@ static int msm_iommu_probe(struct platform_device *pdev)
>  
>  	if (!IS_ERR(iommu_clk))	{
>  		if (clk_get_rate(iommu_clk) == 0)
> -			clk_set_min_rate(iommu_clk, 1);
> +			clk_set_rate(iommu_clk, 1);
>  
>  		ret = clk_prepare_enable(iommu_clk);
>  		if (ret) {
> -- 
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> hosted by The Linux Foundation
> 
> --
> To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html

-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation

Re: [PATCH/RESEND 06/12] msm: iommu: Use clk_set_rate() instead of clk_set_min_rate()

[Joerg Roedel]

On Thu, Jun 20, 2013 at 09:41:42AM -0700, Stephen Boyd wrote:
> Sending to correct Joerg address.
> 
> On 06/17, Stephen Boyd wrote:
> > Calling clk_set_min_rate() is no better than just calling
> > clk_set_rate() because MSM clock code already takes care of
> > calling the min_rate ops if the clock really needs
> > clk_set_min_rate() called on it.
> > 
> > Cc: Joerg Roedel <joerg.roedel@amd.com>
> > Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Acked-by: Joerg Roedel <joro@8bytes.org>

[PATCH/RESEND 07/12] ARM: msm: Remove custom clk_set_flags() API

[Stephen Boyd]

Nobody is using this API upstream and it's just contributing
cruft. Remove it so the MSM clock API is closer to the generic
struct clock API.

Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
 arch/arm/mach-msm/clock-pcom.c       | 10 ----------
 arch/arm/mach-msm/clock.c            |  8 --------
 arch/arm/mach-msm/clock.h            |  6 ------
 arch/arm/mach-msm/include/mach/clk.h |  3 ---
 4 files changed, 27 deletions(-)

diff --git a/arch/arm/mach-msm/clock-pcom.c b/arch/arm/mach-msm/clock-pcom.c
index a52c970..bb75f8e 100644
--- a/arch/arm/mach-msm/clock-pcom.c
+++ b/arch/arm/mach-msm/clock-pcom.c
@@ -85,15 +85,6 @@ static int pc_clk_set_max_rate(unsigned id, unsigned rate)
 		return (int)id < 0 ? -EINVAL : 0;
 }
 
-static int pc_clk_set_flags(unsigned id, unsigned flags)
-{
-	int rc = msm_proc_comm(PCOM_CLKCTL_RPC_SET_FLAGS, &id, &flags);
-	if (rc < 0)
-		return rc;
-	else
-		return (int)id < 0 ? -EINVAL : 0;
-}
-
 static unsigned pc_clk_get_rate(unsigned id)
 {
 	if (msm_proc_comm(PCOM_CLKCTL_RPC_RATE, &id, NULL))
@@ -130,7 +121,6 @@ struct clk_ops clk_ops_pcom = {
 	.set_rate = pc_clk_set_rate,
 	.set_min_rate = pc_clk_set_min_rate,
 	.set_max_rate = pc_clk_set_max_rate,
-	.set_flags = pc_clk_set_flags,
 	.get_rate = pc_clk_get_rate,
 	.is_enabled = pc_clk_is_enabled,
 	.round_rate = pc_clk_round_rate,
diff --git a/arch/arm/mach-msm/clock.c b/arch/arm/mach-msm/clock.c
index d9145df..5fac2df 100644
--- a/arch/arm/mach-msm/clock.c
+++ b/arch/arm/mach-msm/clock.c
@@ -121,14 +121,6 @@ struct clk *clk_get_parent(struct clk *clk)
 }
 EXPORT_SYMBOL(clk_get_parent);
 
-int clk_set_flags(struct clk *clk, unsigned long flags)
-{
-	if (clk == NULL || IS_ERR(clk))
-		return -EINVAL;
-	return clk->ops->set_flags(clk->id, flags);
-}
-EXPORT_SYMBOL(clk_set_flags);
-
 /* EBI1 is the only shared clock that several clients want to vote on as of
  * this commit. If this changes in the future, then it might be better to
  * make clk_min_rate handle the voting or make ebi1_clk_set_min_rate more
diff --git a/arch/arm/mach-msm/clock.h b/arch/arm/mach-msm/clock.h
index 2c007f6..a25ff58 100644
--- a/arch/arm/mach-msm/clock.h
+++ b/arch/arm/mach-msm/clock.h
@@ -21,11 +21,6 @@
 #include <linux/list.h>
 #include <mach/clk.h>
 
-#define CLKFLAG_INVERT			0x00000001
-#define CLKFLAG_NOINVERT		0x00000002
-#define CLKFLAG_NONEST			0x00000004
-#define CLKFLAG_NORESET			0x00000008
-
 #define CLK_FIRST_AVAILABLE_FLAG	0x00000100
 #define CLKFLAG_AUTO_OFF		0x00000200
 #define CLKFLAG_MIN			0x00000400
@@ -39,7 +34,6 @@ struct clk_ops {
 	int (*set_rate)(unsigned id, unsigned rate);
 	int (*set_min_rate)(unsigned id, unsigned rate);
 	int (*set_max_rate)(unsigned id, unsigned rate);
-	int (*set_flags)(unsigned id, unsigned flags);
 	unsigned (*get_rate)(unsigned id);
 	unsigned (*is_enabled)(unsigned id);
 	long (*round_rate)(unsigned id, unsigned rate);
diff --git a/arch/arm/mach-msm/include/mach/clk.h b/arch/arm/mach-msm/include/mach/clk.h
index e8d3842..5f1c37d 100644
--- a/arch/arm/mach-msm/include/mach/clk.h
+++ b/arch/arm/mach-msm/include/mach/clk.h
@@ -34,7 +34,4 @@ int clk_set_max_rate(struct clk *clk, unsigned long rate);
 /* Assert/Deassert reset to a hardware block associated with a clock */
 int clk_reset(struct clk *clk, enum clk_reset_action action);
 
-/* Set clock-specific configuration parameters */
-int clk_set_flags(struct clk *clk, unsigned long flags);
-
 #endif
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation

[PATCH/RESEND 08/12] ARM: msm: Remove custom clk_set_{max,min}_rate() API

[Stephen Boyd]

There are no users of this API anymore so let's just remove it.
If a need arises in the future we can extend the common clock API
to handle it.

Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
 arch/arm/mach-msm/clock-debug.c      |  9 +--------
 arch/arm/mach-msm/clock.c            | 12 ------------
 arch/arm/mach-msm/include/mach/clk.h |  6 ------
 3 files changed, 1 insertion(+), 26 deletions(-)

diff --git a/arch/arm/mach-msm/clock-debug.c b/arch/arm/mach-msm/clock-debug.c
index 4886404..c4b34d7 100644
--- a/arch/arm/mach-msm/clock-debug.c
+++ b/arch/arm/mach-msm/clock-debug.c
@@ -25,14 +25,7 @@ static int clock_debug_rate_set(void *data, u64 val)
 	struct clk *clock = data;
 	int ret;
 
-	/* Only increases to max rate will succeed, but that's actually good
-	 * for debugging purposes so we don't check for error. */
-	if (clock->flags & CLK_MAX)
-		clk_set_max_rate(clock, val);
-	if (clock->flags & CLK_MIN)
-		ret = clk_set_min_rate(clock, val);
-	else
-		ret = clk_set_rate(clock, val);
+	ret = clk_set_rate(clock, val);
 	if (ret != 0)
 		printk(KERN_ERR "clk_set%s_rate failed (%d)\n",
 			(clock->flags & CLK_MIN) ? "_min" : "", ret);
diff --git a/arch/arm/mach-msm/clock.c b/arch/arm/mach-msm/clock.c
index 5fac2df..8d07b25 100644
--- a/arch/arm/mach-msm/clock.c
+++ b/arch/arm/mach-msm/clock.c
@@ -97,18 +97,6 @@ long clk_round_rate(struct clk *clk, unsigned long rate)
 }
 EXPORT_SYMBOL(clk_round_rate);
 
-int clk_set_min_rate(struct clk *clk, unsigned long rate)
-{
-	return clk->ops->set_min_rate(clk->id, rate);
-}
-EXPORT_SYMBOL(clk_set_min_rate);
-
-int clk_set_max_rate(struct clk *clk, unsigned long rate)
-{
-	return clk->ops->set_max_rate(clk->id, rate);
-}
-EXPORT_SYMBOL(clk_set_max_rate);
-
 int clk_set_parent(struct clk *clk, struct clk *parent)
 {
 	return -ENOSYS;
diff --git a/arch/arm/mach-msm/include/mach/clk.h b/arch/arm/mach-msm/include/mach/clk.h
index 5f1c37d..fd4f4a7 100644
--- a/arch/arm/mach-msm/include/mach/clk.h
+++ b/arch/arm/mach-msm/include/mach/clk.h
@@ -25,12 +25,6 @@ enum clk_reset_action {
 
 struct clk;
 
-/* Rate is minimum clock rate in Hz */
-int clk_set_min_rate(struct clk *clk, unsigned long rate);
-
-/* Rate is maximum clock rate in Hz */
-int clk_set_max_rate(struct clk *clk, unsigned long rate);
-
 /* Assert/Deassert reset to a hardware block associated with a clock */
 int clk_reset(struct clk *clk, enum clk_reset_action action);
 
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation

[PATCH/RESEND 09/12] ARM: msm: Remove clock-7x30.h include file

[Stephen Boyd]

This file is not used outside of the two users in the clock-7x30
array. Those two clocks are virtual "source" clocks that don't
really need to exist outside of the clock driver. Let's remove
them from the array, since they're not doing anything anyway, and
then remove the clock-7x30.h include file along with it.

Cc: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
 arch/arm/mach-msm/clock-7x30.h      | 155 ------------------------------------
 arch/arm/mach-msm/devices-msm7x30.c |   3 -
 2 files changed, 158 deletions(-)
 delete mode 100644 arch/arm/mach-msm/clock-7x30.h

diff --git a/arch/arm/mach-msm/clock-7x30.h b/arch/arm/mach-msm/clock-7x30.h
deleted file mode 100644
index 1410445..0000000
--- a/arch/arm/mach-msm/clock-7x30.h
+++ /dev/null
@@ -1,155 +0,0 @@
-/* Copyright (c) 2009, Code Aurora Forum. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef __ARCH_ARM_MACH_MSM_CLOCK_7X30_H
-#define __ARCH_ARM_MACH_MSM_CLOCK_7X30_H
-
-enum {
-	L_7X30_NONE_CLK = -1,
-	L_7X30_ADM_CLK,
-	L_7X30_I2C_CLK,
-	L_7X30_I2C_2_CLK,
-	L_7X30_QUP_I2C_CLK,
-	L_7X30_UART1DM_CLK,
-	L_7X30_UART1DM_P_CLK,
-	L_7X30_UART2DM_CLK,
-	L_7X30_UART2DM_P_CLK,
-	L_7X30_EMDH_CLK,
-	L_7X30_EMDH_P_CLK,
-	L_7X30_PMDH_CLK,
-	L_7X30_PMDH_P_CLK,
-	L_7X30_GRP_2D_CLK,
-	L_7X30_GRP_2D_P_CLK,
-	L_7X30_GRP_3D_SRC_CLK,
-	L_7X30_GRP_3D_CLK,
-	L_7X30_GRP_3D_P_CLK,
-	L_7X30_IMEM_CLK,
-	L_7X30_SDC1_CLK,
-	L_7X30_SDC1_P_CLK,
-	L_7X30_SDC2_CLK,
-	L_7X30_SDC2_P_CLK,
-	L_7X30_SDC3_CLK,
-	L_7X30_SDC3_P_CLK,
-	L_7X30_SDC4_CLK,
-	L_7X30_SDC4_P_CLK,
-	L_7X30_MDP_CLK,
-	L_7X30_MDP_P_CLK,
-	L_7X30_MDP_LCDC_PCLK_CLK,
-	L_7X30_MDP_LCDC_PAD_PCLK_CLK,
-	L_7X30_MDP_VSYNC_CLK,
-	L_7X30_MI2S_CODEC_RX_M_CLK,
-	L_7X30_MI2S_CODEC_RX_S_CLK,
-	L_7X30_MI2S_CODEC_TX_M_CLK,
-	L_7X30_MI2S_CODEC_TX_S_CLK,
-	L_7X30_MI2S_M_CLK,
-	L_7X30_MI2S_S_CLK,
-	L_7X30_LPA_CODEC_CLK,
-	L_7X30_LPA_CORE_CLK,
-	L_7X30_LPA_P_CLK,
-	L_7X30_MIDI_CLK,
-	L_7X30_MDC_CLK,
-	L_7X30_ROTATOR_IMEM_CLK,
-	L_7X30_ROTATOR_P_CLK,
-	L_7X30_SDAC_M_CLK,
-	L_7X30_SDAC_CLK,
-	L_7X30_UART1_CLK,
-	L_7X30_UART2_CLK,
-	L_7X30_UART3_CLK,
-	L_7X30_TV_CLK,
-	L_7X30_TV_DAC_CLK,
-	L_7X30_TV_ENC_CLK,
-	L_7X30_HDMI_CLK,
-	L_7X30_TSIF_REF_CLK,
-	L_7X30_TSIF_P_CLK,
-	L_7X30_USB_HS_SRC_CLK,
-	L_7X30_USB_HS_CLK,
-	L_7X30_USB_HS_CORE_CLK,
-	L_7X30_USB_HS_P_CLK,
-	L_7X30_USB_HS2_CLK,
-	L_7X30_USB_HS2_CORE_CLK,
-	L_7X30_USB_HS2_P_CLK,
-	L_7X30_USB_HS3_CLK,
-	L_7X30_USB_HS3_CORE_CLK,
-	L_7X30_USB_HS3_P_CLK,
-	L_7X30_VFE_CLK,
-	L_7X30_VFE_P_CLK,
-	L_7X30_VFE_MDC_CLK,
-	L_7X30_VFE_CAMIF_CLK,
-	L_7X30_CAMIF_PAD_P_CLK,
-	L_7X30_CAM_M_CLK,
-	L_7X30_JPEG_CLK,
-	L_7X30_JPEG_P_CLK,
-	L_7X30_VPE_CLK,
-	L_7X30_MFC_CLK,
-	L_7X30_MFC_DIV2_CLK,
-	L_7X30_MFC_P_CLK,
-	L_7X30_SPI_CLK,
-	L_7X30_SPI_P_CLK,
-	L_7X30_CSI0_CLK,
-	L_7X30_CSI0_VFE_CLK,
-	L_7X30_CSI0_P_CLK,
-	L_7X30_CSI1_CLK,
-	L_7X30_CSI1_VFE_CLK,
-	L_7X30_CSI1_P_CLK,
-	L_7X30_GLBL_ROOT_CLK,
-
-	L_7X30_AXI_LI_VG_CLK,
-	L_7X30_AXI_LI_GRP_CLK,
-	L_7X30_AXI_LI_JPEG_CLK,
-	L_7X30_AXI_GRP_2D_CLK,
-	L_7X30_AXI_MFC_CLK,
-	L_7X30_AXI_VPE_CLK,
-	L_7X30_AXI_LI_VFE_CLK,
-	L_7X30_AXI_LI_APPS_CLK,
-	L_7X30_AXI_MDP_CLK,
-	L_7X30_AXI_IMEM_CLK,
-	L_7X30_AXI_LI_ADSP_A_CLK,
-	L_7X30_AXI_ROTATOR_CLK,
-
-	L_7X30_NR_CLKS
-};
-
-struct clk_ops;
-extern struct clk_ops clk_ops_7x30;
-
-struct clk_ops *clk_7x30_is_local(uint32_t id);
-int clk_7x30_init(void);
-
-void pll_enable(uint32_t pll);
-void pll_disable(uint32_t pll);
-
-extern int internal_pwr_rail_ctl_auto(unsigned rail_id, bool enable);
-
-#define CLK_7X30(clk_name, clk_id, clk_dev, clk_flags) {	\
-	.con_id = clk_name, \
-	.dev_id = clk_dev, \
-	.clk = &(struct clk){ \
-		.id = L_7X30_##clk_id, \
-		.remote_id = P_##clk_id, \
-		.flags = clk_flags, \
-		.dbg_name = #clk_id, \
-	}, \
-	}
-
-#define CLK_7X30S(clk_name, l_id, r_id, clk_dev, clk_flags) {	\
-	.con_id = clk_name, \
-	.dev_id = clk_dev, \
-	.clk = &(struct clk){ \
-		.id = L_7X30_##l_id, \
-		.remote_id = P_##r_id, \
-		.flags = clk_flags, \
-		.dbg_name = #l_id, \
-		.ops = &clk_ops_pcom, \
-	}, \
-	}
-
-#endif
diff --git a/arch/arm/mach-msm/devices-msm7x30.c b/arch/arm/mach-msm/devices-msm7x30.c
index 12f482c..d233c51 100644
--- a/arch/arm/mach-msm/devices-msm7x30.c
+++ b/arch/arm/mach-msm/devices-msm7x30.c
@@ -29,7 +29,6 @@
 #include <asm/mach/flash.h>
 
 #include "clock-pcom.h"
-#include "clock-7x30.h"
 
 #include <linux/platform_data/mmc-msm_sdcc.h>
 
@@ -177,7 +176,6 @@ struct clk_lookup msm_clocks_7x30[] = {
 	CLK_PCOM("grp_2d_pclk",	GRP_2D_P_CLK,	NULL, 0),
 	CLK_PCOM("grp_clk",	GRP_3D_CLK,	NULL, 0),
 	CLK_PCOM("grp_pclk",	GRP_3D_P_CLK,	NULL, 0),
-	CLK_7X30S("grp_src_clk", GRP_3D_SRC_CLK, GRP_3D_CLK,	NULL, 0),
 	CLK_PCOM("hdmi_clk",	HDMI_CLK,	NULL, 0),
 	CLK_PCOM("imem_clk",	IMEM_CLK,	NULL, OFF),
 	CLK_PCOM("jpeg_clk",	JPEG_CLK,	NULL, OFF),
@@ -210,7 +208,6 @@ struct clk_lookup msm_clocks_7x30[] = {
 	CLK_PCOM("sdac_clk",	SDAC_CLK,	NULL, OFF),
 	CLK_PCOM("spi_clk",	SPI_CLK,	NULL, 0),
 	CLK_PCOM("spi_pclk",	SPI_P_CLK,	NULL, 0),
-	CLK_7X30S("tv_src_clk",	TV_CLK, 	TV_ENC_CLK,	NULL, 0),
 	CLK_PCOM("tv_dac_clk",	TV_DAC_CLK,	NULL, 0),
 	CLK_PCOM("tv_enc_clk",	TV_ENC_CLK,	NULL, 0),
 	CLK_PCOM("uart_clk",	UART2_CLK,	"msm_serial.1", 0),
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation

[PATCH/RESEND 10/12] ARM: msm: Prepare clk_get() users in mach-msm for clock-pcom driver

[Stephen Boyd]

In the near future we'll be moving clock-pcom to a platform
driver, in which case these two users of clk_get() in mach-msm
need to be updated. Have board-trout-panel.c make the proc_comm
call directly so that we don't have to port this board specific
code to the driver right now and reorder the initcall order of
dma.c so that it initializes after the clock driver probes but
before any drivers use dma APIs.

Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
 arch/arm/mach-msm/Makefile            |  9 ++++++---
 arch/arm/mach-msm/board-trout-panel.c | 19 +++++++------------
 arch/arm/mach-msm/dma.c               |  5 ++---
 3 files changed, 15 insertions(+), 18 deletions(-)

diff --git a/arch/arm/mach-msm/Makefile b/arch/arm/mach-msm/Makefile
index 17519fa..3dbae74 100644
--- a/arch/arm/mach-msm/Makefile
+++ b/arch/arm/mach-msm/Makefile
@@ -5,12 +5,15 @@ obj-$(CONFIG_DEBUG_FS) += clock-debug.o
 obj-$(CONFIG_MSM_VIC) += irq-vic.o
 obj-$(CONFIG_MSM_IOMMU) += devices-iommu.o
 
-obj-$(CONFIG_ARCH_MSM7X00A) += dma.o irq.o
-obj-$(CONFIG_ARCH_MSM7X30) += dma.o
-obj-$(CONFIG_ARCH_QSD8X50) += dma.o sirc.o
+obj-$(CONFIG_ARCH_MSM7X00A) += irq.o
+obj-$(CONFIG_ARCH_QSD8X50) += sirc.o
 
 obj-$(CONFIG_MSM_PROC_COMM) += proc_comm.o clock-pcom.o vreg.o
 
+obj-$(CONFIG_ARCH_MSM7X00A) += dma.o
+obj-$(CONFIG_ARCH_MSM7X30) += dma.o
+obj-$(CONFIG_ARCH_QSD8X50) += dma.o
+
 obj-$(CONFIG_MSM_SMD) += smd.o smd_debug.o
 obj-$(CONFIG_MSM_SMD) += last_radio_log.o
 obj-$(CONFIG_MSM_SCM) += scm.o scm-boot.o
diff --git a/arch/arm/mach-msm/board-trout-panel.c b/arch/arm/mach-msm/board-trout-panel.c
index f9a5db6..77b0a26 100644
--- a/arch/arm/mach-msm/board-trout-panel.c
+++ b/arch/arm/mach-msm/board-trout-panel.c
@@ -7,7 +7,6 @@
 #include <linux/platform_device.h>
 #include <linux/delay.h>
 #include <linux/leds.h>
-#include <linux/clk.h>
 #include <linux/err.h>
 
 #include <asm/io.h>
@@ -19,6 +18,7 @@
 
 #include "board-trout.h"
 #include "proc_comm.h"
+#include "clock-pcom.h"
 #include "devices.h"
 
 #define TROUT_DEFAULT_BACKLIGHT_BRIGHTNESS 255
@@ -170,7 +170,6 @@ static struct mddi_table mddi_toshiba_init_table[] = {
 #define INTMASK_VWAKEOUT (1U << 0)
 
 
-static struct clk *gp_clk;
 static int trout_new_backlight = 1;
 static struct vreg *vreg_mddi_1v5;
 static struct vreg *vreg_lcm_2v85;
@@ -273,18 +272,14 @@ int __init trout_init_panel(void)
 	} else {
 		uint32_t config = PCOM_GPIO_CFG(27, 1, GPIO_OUTPUT,
 						GPIO_NO_PULL, GPIO_8MA);
+		uint32_t id = P_GP_CLK;
+		uint32_t rate = 19200000;
+
 		msm_proc_comm(PCOM_RPC_GPIO_TLMM_CONFIG_EX, &config, 0);
 
-		gp_clk = clk_get(NULL, "gp_clk");
-		if (IS_ERR(gp_clk)) {
-			printk(KERN_ERR "trout_init_panel: could not get gp"
-			       "clock\n");
-			gp_clk = NULL;
-		}
-		rc = clk_set_rate(gp_clk, 19200000);
-		if (rc)
-			printk(KERN_ERR "trout_init_panel: set clock rate "
-			       "failed\n");
+		msm_proc_comm(PCOM_CLKCTL_RPC_SET_RATE, &id, &rate);
+		if (id < 0)
+			pr_err("trout_init_panel: set clock rate failed\n");
 	}
 
 	rc = platform_device_register(&msm_device_mdp);
diff --git a/arch/arm/mach-msm/dma.c b/arch/arm/mach-msm/dma.c
index b279fd8..f8f6adf 100644
--- a/arch/arm/mach-msm/dma.c
+++ b/arch/arm/mach-msm/dma.c
@@ -284,6 +284,7 @@ static int __init msm_init_datamover(void)
 	clk = clk_get(NULL, "adm_clk");
 	if (IS_ERR(clk))
 		return PTR_ERR(clk);
+	clk_prepare(clk);
 	msm_dmov_clk = clk;
 	ret = request_irq(INT_ADM_AARM, msm_datamover_irq_handler, 0, "msmdatamover", NULL);
 	if (ret)
@@ -291,6 +292,4 @@ static int __init msm_init_datamover(void)
 	disable_irq(INT_ADM_AARM);
 	return 0;
 }
-
-arch_initcall(msm_init_datamover);
-
+module_init(msm_init_datamover);
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation

[PATCH/RESEND 11/12] ARM: msm: Make proc_comm clock control into a platform driver

[Stephen Boyd]

To move closer to the generic struct clock framework move the
proc_comm based clock code to a platform driver. The data
describing the struct clks still live in the devices-$ARCH file,
but the clock initialization is done at driver binding time.

Cc: Saravana Kannan <skannan@codeaurora.org>
Reviewed-by: Pankaj Jangra <jangra.pankaj9@gmail.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
 arch/arm/mach-msm/board-halibut.c      |  2 +-
 arch/arm/mach-msm/board-msm7x30.c      |  2 +-
 arch/arm/mach-msm/board-qsd8x50.c      |  2 +-
 arch/arm/mach-msm/board-trout.c        |  3 +--
 arch/arm/mach-msm/clock-pcom.c         | 23 +++++++++++++++++++++--
 arch/arm/mach-msm/clock-pcom.h         |  5 +++++
 arch/arm/mach-msm/clock.c              |  2 +-
 arch/arm/mach-msm/clock.h              |  3 +++
 arch/arm/mach-msm/devices-msm7x00.c    | 12 ++++++++++--
 arch/arm/mach-msm/devices-msm7x30.c    | 11 +++++++++--
 arch/arm/mach-msm/devices-qsd8x50.c    | 11 +++++++++--
 arch/arm/mach-msm/devices.h            | 15 +++------------
 arch/arm/mach-msm/include/mach/board.h |  5 -----
 13 files changed, 65 insertions(+), 31 deletions(-)

diff --git a/arch/arm/mach-msm/board-halibut.c b/arch/arm/mach-msm/board-halibut.c
index 82eaf88..803651a 100644
--- a/arch/arm/mach-msm/board-halibut.c
+++ b/arch/arm/mach-msm/board-halibut.c
@@ -59,6 +59,7 @@ static struct platform_device smc91x_device = {
 };
 
 static struct platform_device *devices[] __initdata = {
+	&msm_clock_7x01a,
 	&msm_device_gpio_7201,
 	&msm_device_uart3,
 	&msm_device_smd,
@@ -91,7 +92,6 @@ static void __init halibut_fixup(struct tag *tags, char **cmdline,
 static void __init halibut_map_io(void)
 {
 	msm_map_common_io();
-	msm_clock_init(msm_clocks_7x01a, msm_num_clocks_7x01a);
 }
 
 static void __init halibut_init_late(void)
diff --git a/arch/arm/mach-msm/board-msm7x30.c b/arch/arm/mach-msm/board-msm7x30.c
index 520c141..db3d8c0 100644
--- a/arch/arm/mach-msm/board-msm7x30.c
+++ b/arch/arm/mach-msm/board-msm7x30.c
@@ -89,6 +89,7 @@ struct msm_gpiomux_config msm_gpiomux_configs[GPIOMUX_NGPIOS] = {
 };
 
 static struct platform_device *devices[] __initdata = {
+	&msm_clock_7x30,
 	&msm_device_gpio_7x30,
 #if defined(CONFIG_SERIAL_MSM) || defined(CONFIG_MSM_SERIAL_DEBUGGER)
         &msm_device_uart2,
@@ -116,7 +117,6 @@ static void __init msm7x30_init(void)
 static void __init msm7x30_map_io(void)
 {
 	msm_map_msm7x30_io();
-	msm_clock_init(msm_clocks_7x30, msm_num_clocks_7x30);
 }
 
 static void __init msm7x30_init_late(void)
diff --git a/arch/arm/mach-msm/board-qsd8x50.c b/arch/arm/mach-msm/board-qsd8x50.c
index 38a532d..f14a73d 100644
--- a/arch/arm/mach-msm/board-qsd8x50.c
+++ b/arch/arm/mach-msm/board-qsd8x50.c
@@ -89,6 +89,7 @@ static struct msm_otg_platform_data msm_otg_pdata = {
 };
 
 static struct platform_device *devices[] __initdata = {
+	&msm_clock_8x50,
 	&msm_device_gpio_8x50,
 	&msm_device_uart3,
 	&msm_device_smd,
@@ -172,7 +173,6 @@ static void __init qsd8x50_init_mmc(void)
 static void __init qsd8x50_map_io(void)
 {
 	msm_map_qsd8x50_io();
-	msm_clock_init(msm_clocks_8x50, msm_num_clocks_8x50);
 }
 
 static void __init qsd8x50_init_irq(void)
diff --git a/arch/arm/mach-msm/board-trout.c b/arch/arm/mach-msm/board-trout.c
index 80fe1c5..64a46eb 100644
--- a/arch/arm/mach-msm/board-trout.c
+++ b/arch/arm/mach-msm/board-trout.c
@@ -36,6 +36,7 @@
 extern int trout_init_mmc(unsigned int);
 
 static struct platform_device *devices[] __initdata = {
+	&msm_clock_7x01a,
 	&msm_device_gpio_7201,
 	&msm_device_uart3,
 	&msm_device_smd,
@@ -94,8 +95,6 @@ static void __init trout_map_io(void)
 	/* route UART3 to the "H2W" extended usb connector */
 	writeb(0x80, TROUT_CPLD_BASE + 0x00);
 #endif
-
-	msm_clock_init(msm_clocks_7x01a, msm_num_clocks_7x01a);
 }
 
 static void __init trout_init_late(void)
diff --git a/arch/arm/mach-msm/clock-pcom.c b/arch/arm/mach-msm/clock-pcom.c
index bb75f8e..6321731 100644
--- a/arch/arm/mach-msm/clock-pcom.c
+++ b/arch/arm/mach-msm/clock-pcom.c
@@ -14,8 +14,9 @@
  */
 
 #include <linux/err.h>
-#include <linux/ctype.h>
-#include <linux/stddef.h>
+#include <linux/platform_device.h>
+#include <linux/module.h>
+
 #include <mach/clk.h>
 
 #include "proc_comm.h"
@@ -126,3 +127,21 @@ struct clk_ops clk_ops_pcom = {
 	.round_rate = pc_clk_round_rate,
 	.is_local = pc_clk_is_local,
 };
+
+static int msm_clock_pcom_probe(struct platform_device *pdev)
+{
+	const struct pcom_clk_pdata *pdata = pdev->dev.platform_data;
+	msm_clock_init(pdata->lookup, pdata->num_lookups);
+	return 0;
+}
+
+static struct platform_driver msm_clock_pcom_driver = {
+	.probe		= msm_clock_pcom_probe,
+	.driver		= {
+		.name	= "msm-clock-pcom",
+		.owner	= THIS_MODULE,
+	},
+};
+module_platform_driver(msm_clock_pcom_driver);
+
+MODULE_LICENSE("GPL v2");
diff --git a/arch/arm/mach-msm/clock-pcom.h b/arch/arm/mach-msm/clock-pcom.h
index 974d003..87406a3 100644
--- a/arch/arm/mach-msm/clock-pcom.h
+++ b/arch/arm/mach-msm/clock-pcom.h
@@ -123,6 +123,11 @@
 struct clk_ops;
 extern struct clk_ops clk_ops_pcom;
 
+struct pcom_clk_pdata {
+	struct clk_lookup *lookup;
+	u32 num_lookups;
+};
+
 int pc_clk_reset(unsigned id, enum clk_reset_action action);
 
 #define CLK_PCOM(clk_name, clk_id, clk_dev, clk_flags) {	\
diff --git a/arch/arm/mach-msm/clock.c b/arch/arm/mach-msm/clock.c
index 8d07b25..01af7a4 100644
--- a/arch/arm/mach-msm/clock.c
+++ b/arch/arm/mach-msm/clock.c
@@ -116,7 +116,7 @@ EXPORT_SYMBOL(clk_get_parent);
  */
 static struct clk *ebi1_clk;
 
-void __init msm_clock_init(struct clk_lookup *clock_tbl, unsigned num_clocks)
+void msm_clock_init(struct clk_lookup *clock_tbl, size_t num_clocks)
 {
 	unsigned n;
 
diff --git a/arch/arm/mach-msm/clock.h b/arch/arm/mach-msm/clock.h
index a25ff58..cc76bfe 100644
--- a/arch/arm/mach-msm/clock.h
+++ b/arch/arm/mach-msm/clock.h
@@ -63,4 +63,7 @@ static inline int __init clock_debug_init(void) { return 0; }
 static inline int __init clock_debug_add(struct clk *clock) { return 0; }
 #endif
 
+struct clk_lookup;
+void msm_clock_init(struct clk_lookup *clock_tbl, size_t num_clocks);
+
 #endif
diff --git a/arch/arm/mach-msm/devices-msm7x00.c b/arch/arm/mach-msm/devices-msm7x00.c
index 1a0a230..9edfe68 100644
--- a/arch/arm/mach-msm/devices-msm7x00.c
+++ b/arch/arm/mach-msm/devices-msm7x00.c
@@ -425,7 +425,7 @@ struct platform_device msm_device_mdp = {
 	.resource = resources_mdp,
 };
 
-struct clk_lookup msm_clocks_7x01a[] = {
+static struct clk_lookup msm_clocks_7x01a[] = {
 	CLK_PCOM("adm_clk",	ADM_CLK,	NULL, 0),
 	CLK_PCOM("adsp_clk",	ADSP_CLK,	NULL, 0),
 	CLK_PCOM("ebi1_clk",	EBI1_CLK,	NULL, 0),
@@ -469,4 +469,12 @@ struct clk_lookup msm_clocks_7x01a[] = {
 	CLK_PCOM("vfe_mdc_clk",	VFE_MDC_CLK,	NULL, OFF),
 };
 
-unsigned msm_num_clocks_7x01a = ARRAY_SIZE(msm_clocks_7x01a);
+static struct pcom_clk_pdata msm_clock_7x01a_pdata = {
+	.lookup = msm_clocks_7x01a,
+	.num_lookups = ARRAY_SIZE(msm_clocks_7x01a),
+};
+
+struct platform_device msm_clock_7x01a = {
+	.name = "msm-clock-pcom",
+	.dev.platform_data = &msm_clock_7x01a_pdata,
+};
diff --git a/arch/arm/mach-msm/devices-msm7x30.c b/arch/arm/mach-msm/devices-msm7x30.c
index d233c51..e877fd6 100644
--- a/arch/arm/mach-msm/devices-msm7x30.c
+++ b/arch/arm/mach-msm/devices-msm7x30.c
@@ -160,7 +160,7 @@ struct platform_device msm_device_hsusb_host = {
 	},
 };
 
-struct clk_lookup msm_clocks_7x30[] = {
+static struct clk_lookup msm_clocks_7x30[] = {
 	CLK_PCOM("adm_clk",	ADM_CLK,	NULL, 0),
 	CLK_PCOM("adsp_clk",	ADSP_CLK,	NULL, 0),
 	CLK_PCOM("cam_m_clk",	CAM_M_CLK,	NULL, 0),
@@ -234,5 +234,12 @@ struct clk_lookup msm_clocks_7x30[] = {
 	CLK_PCOM("csi_vfe_clk",	CSI0_VFE_CLK,	NULL, 0),
 };
 
-unsigned msm_num_clocks_7x30 = ARRAY_SIZE(msm_clocks_7x30);
+static struct pcom_clk_pdata msm_clock_7x30_pdata = {
+	.lookup = msm_clocks_7x30,
+	.num_lookups = ARRAY_SIZE(msm_clocks_7x30),
+};
 
+struct platform_device msm_clock_7x30 = {
+	.name = "msm-clock-pcom",
+	.dev.platform_data = &msm_clock_7x30_pdata,
+};
diff --git a/arch/arm/mach-msm/devices-qsd8x50.c b/arch/arm/mach-msm/devices-qsd8x50.c
index 2e1b3ec..a62f647 100644
--- a/arch/arm/mach-msm/devices-qsd8x50.c
+++ b/arch/arm/mach-msm/devices-qsd8x50.c
@@ -322,7 +322,7 @@ int __init msm_add_sdcc(unsigned int controller,
 	return platform_device_register(pdev);
 }
 
-struct clk_lookup msm_clocks_8x50[] = {
+static struct clk_lookup msm_clocks_8x50[] = {
 	CLK_PCOM("adm_clk",	ADM_CLK,	NULL, 0),
 	CLK_PCOM("ce_clk",	CE_CLK,		NULL, 0),
 	CLK_PCOM("ebi1_clk",	EBI1_CLK,	NULL, CLK_MIN),
@@ -376,5 +376,12 @@ struct clk_lookup msm_clocks_8x50[] = {
 	CLK_PCOM("usb_phy_clk",	USB_PHY_CLK,	NULL, 0),
 };
 
-unsigned msm_num_clocks_8x50 = ARRAY_SIZE(msm_clocks_8x50);
+static struct pcom_clk_pdata msm_clock_8x50_pdata = {
+	.lookup = msm_clocks_8x50,
+	.num_lookups = ARRAY_SIZE(msm_clocks_8x50),
+};
 
+struct platform_device msm_clock_8x50 = {
+	.name = "msm-clock-pcom",
+	.dev.platform_data = &msm_clock_8x50_pdata,
+};
diff --git a/arch/arm/mach-msm/devices.h b/arch/arm/mach-msm/devices.h
index da902cf..dccefad 100644
--- a/arch/arm/mach-msm/devices.h
+++ b/arch/arm/mach-msm/devices.h
@@ -16,10 +16,6 @@
 #ifndef __ARCH_ARM_MACH_MSM_DEVICES_H
 #define __ARCH_ARM_MACH_MSM_DEVICES_H
 
-#include <linux/clkdev.h>
-
-#include "clock.h"
-
 extern struct platform_device msm_device_gpio_7201;
 extern struct platform_device msm_device_gpio_7x30;
 extern struct platform_device msm_device_gpio_8x50;
@@ -50,13 +46,8 @@ extern struct platform_device msm_device_mddi0;
 extern struct platform_device msm_device_mddi1;
 extern struct platform_device msm_device_mdp;
 
-extern struct clk_lookup msm_clocks_7x01a[];
-extern unsigned msm_num_clocks_7x01a;
-
-extern struct clk_lookup msm_clocks_7x30[];
-extern unsigned msm_num_clocks_7x30;
-
-extern struct clk_lookup msm_clocks_8x50[];
-extern unsigned msm_num_clocks_8x50;
+extern struct platform_device msm_clock_7x01a;
+extern struct platform_device msm_clock_7x30;
+extern struct platform_device msm_clock_8x50;
 
 #endif
diff --git a/arch/arm/mach-msm/include/mach/board.h b/arch/arm/mach-msm/include/mach/board.h
index 8cebedb..c34e246 100644
--- a/arch/arm/mach-msm/include/mach/board.h
+++ b/arch/arm/mach-msm/include/mach/board.h
@@ -20,16 +20,11 @@
 #include <linux/types.h>
 #include <linux/platform_data/mmc-msm_sdcc.h>
 
-/* platform device data structures */
-
-struct clk_lookup;
-
 /* common init routines for use by arch/arm/mach-msm/board-*.c */
 
 void __init msm_add_devices(void);
 void __init msm_init_irq(void);
 void __init msm_init_gpio(void);
-void __init msm_clock_init(struct clk_lookup *clock_tbl, unsigned num_clocks);
 int __init msm_add_sdcc(unsigned int controller,
 			struct msm_mmc_platform_data *plat,
 			unsigned int stat_irq, unsigned long stat_irq_flags);
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation

Re: [PATCH/RESEND 11/12] ARM: msm: Make proc_comm clock control into a platform driver

[Stephen Boyd]

On 06/17, Stephen Boyd wrote:
> diff --git a/arch/arm/mach-msm/devices.h b/arch/arm/mach-msm/devices.h
> index da902cf..dccefad 100644
> --- a/arch/arm/mach-msm/devices.h
> +++ b/arch/arm/mach-msm/devices.h
> @@ -16,10 +16,6 @@
>  #ifndef __ARCH_ARM_MACH_MSM_DEVICES_H
>  #define __ARCH_ARM_MACH_MSM_DEVICES_H
>  
> -#include <linux/clkdev.h>
> -
> -#include "clock.h"
> -

This removal causes a build failure on 7x30/8x50. Please squash in
this small fixup when applying.

---8<-----
diff --git a/arch/arm/mach-msm/devices-msm7x30.c b/arch/arm/mach-msm/devices-msm7x30.c
index be45136..d4db75a 100644
--- a/arch/arm/mach-msm/devices-msm7x30.c
+++ b/arch/arm/mach-msm/devices-msm7x30.c
@@ -28,6 +28,7 @@
 
 #include <asm/mach/flash.h>
 
+#include "clock.h"
 #include "clock-pcom.h"
 
 #include <linux/platform_data/mmc-msm_sdcc.h>
diff --git a/arch/arm/mach-msm/devices-qsd8x50.c b/arch/arm/mach-msm/devices-qsd8x50.c
index 3fd8f88..f551811 100644
--- a/arch/arm/mach-msm/devices-qsd8x50.c
+++ b/arch/arm/mach-msm/devices-qsd8x50.c
@@ -28,6 +28,7 @@
 #include <asm/mach/flash.h>
 
 #include <linux/platform_data/mmc-msm_sdcc.h>
+#include "clock.h"
 #include "clock-pcom.h"
 
 static struct resource msm_gpio_resources[] = {

-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation

[PATCH/RESEND 12/12] ARM: msm: Migrate to common clock framework

[Stephen Boyd]

Move the existing clock code in mach-msm to the common clock
framework. We lose our capability to set the rate of and enable a
clock through debugfs. This is ok though because the debugfs
features are mainly used for testing and development of new clock
code.

To maintain compatibility with the original MSM clock code we
make a wrapper for clk_reset() that calls the struct msm_clk
specific reset function. This is necessary for the usb and sdcc
devices on MSM until a better suited API is made available.

Cc: Saravana Kannan <skannan@codeaurora.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
 arch/arm/Kconfig                    |   2 +-
 arch/arm/mach-msm/Makefile          |   1 -
 arch/arm/mach-msm/clock-debug.c     | 123 ------------------------------
 arch/arm/mach-msm/clock-pcom.c      | 118 ++++++++++++++++++-----------
 arch/arm/mach-msm/clock-pcom.h      |  30 ++++----
 arch/arm/mach-msm/clock.c           | 146 ++----------------------------------
 arch/arm/mach-msm/clock.h           |  46 +++---------
 arch/arm/mach-msm/devices-msm7x00.c |   2 +-
 arch/arm/mach-msm/devices-msm7x30.c |   2 +-
 arch/arm/mach-msm/devices-qsd8x50.c |   2 +-
 10 files changed, 108 insertions(+), 364 deletions(-)
 delete mode 100644 arch/arm/mach-msm/clock-debug.c

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 49d993c..380091b 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -623,8 +623,8 @@ config ARCH_MSM
 	bool "Qualcomm MSM"
 	select ARCH_REQUIRE_GPIOLIB
 	select CLKDEV_LOOKUP
+	select COMMON_CLK
 	select GENERIC_CLOCKEVENTS
-	select HAVE_CLK
 	help
 	  Support for Qualcomm MSM/QSD based systems.  This runs on the
 	  apps processor of the MSM/QSD and depends on a shared memory
diff --git a/arch/arm/mach-msm/Makefile b/arch/arm/mach-msm/Makefile
index 3dbae74..700d77b 100644
--- a/arch/arm/mach-msm/Makefile
+++ b/arch/arm/mach-msm/Makefile
@@ -1,6 +1,5 @@
 obj-y += io.o timer.o
 obj-y += clock.o
-obj-$(CONFIG_DEBUG_FS) += clock-debug.o
 
 obj-$(CONFIG_MSM_VIC) += irq-vic.o
 obj-$(CONFIG_MSM_IOMMU) += devices-iommu.o
diff --git a/arch/arm/mach-msm/clock-debug.c b/arch/arm/mach-msm/clock-debug.c
deleted file mode 100644
index c4b34d7..0000000
--- a/arch/arm/mach-msm/clock-debug.c
+++ /dev/null
@@ -1,123 +0,0 @@
-/*
- * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2007-2010, Code Aurora Forum. All rights reserved.
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/ctype.h>
-#include <linux/debugfs.h>
-#include <linux/clk.h>
-#include "clock.h"
-
-static int clock_debug_rate_set(void *data, u64 val)
-{
-	struct clk *clock = data;
-	int ret;
-
-	ret = clk_set_rate(clock, val);
-	if (ret != 0)
-		printk(KERN_ERR "clk_set%s_rate failed (%d)\n",
-			(clock->flags & CLK_MIN) ? "_min" : "", ret);
-	return ret;
-}
-
-static int clock_debug_rate_get(void *data, u64 *val)
-{
-	struct clk *clock = data;
-	*val = clk_get_rate(clock);
-	return 0;
-}
-
-DEFINE_SIMPLE_ATTRIBUTE(clock_rate_fops, clock_debug_rate_get,
-			clock_debug_rate_set, "%llu\n");
-
-static int clock_debug_enable_set(void *data, u64 val)
-{
-	struct clk *clock = data;
-	int rc = 0;
-
-	if (val)
-		rc = clock->ops->enable(clock->id);
-	else
-		clock->ops->disable(clock->id);
-
-	return rc;
-}
-
-static int clock_debug_enable_get(void *data, u64 *val)
-{
-	struct clk *clock = data;
-
-	*val = clock->ops->is_enabled(clock->id);
-
-	return 0;
-}
-
-DEFINE_SIMPLE_ATTRIBUTE(clock_enable_fops, clock_debug_enable_get,
-			clock_debug_enable_set, "%llu\n");
-
-static int clock_debug_local_get(void *data, u64 *val)
-{
-	struct clk *clock = data;
-
-	*val = clock->ops->is_local(clock->id);
-
-	return 0;
-}
-
-DEFINE_SIMPLE_ATTRIBUTE(clock_local_fops, clock_debug_local_get,
-			NULL, "%llu\n");
-
-static struct dentry *debugfs_base;
-
-int __init clock_debug_init(void)
-{
-	debugfs_base = debugfs_create_dir("clk", NULL);
-	if (!debugfs_base)
-		return -ENOMEM;
-	return 0;
-}
-
-int __init clock_debug_add(struct clk *clock)
-{
-	char temp[50], *ptr;
-	struct dentry *clk_dir;
-
-	if (!debugfs_base)
-		return -ENOMEM;
-
-	strncpy(temp, clock->dbg_name, ARRAY_SIZE(temp)-1);
-	for (ptr = temp; *ptr; ptr++)
-		*ptr = tolower(*ptr);
-
-	clk_dir = debugfs_create_dir(temp, debugfs_base);
-	if (!clk_dir)
-		return -ENOMEM;
-
-	if (!debugfs_create_file("rate", S_IRUGO | S_IWUSR, clk_dir,
-				clock, &clock_rate_fops))
-		goto error;
-
-	if (!debugfs_create_file("enable", S_IRUGO | S_IWUSR, clk_dir,
-				clock, &clock_enable_fops))
-		goto error;
-
-	if (!debugfs_create_file("is_local", S_IRUGO, clk_dir, clock,
-				&clock_local_fops))
-		goto error;
-	return 0;
-error:
-	debugfs_remove_recursive(clk_dir);
-	return -ENOMEM;
-}
diff --git a/arch/arm/mach-msm/clock-pcom.c b/arch/arm/mach-msm/clock-pcom.c
index 6321731..9a80449 100644
--- a/arch/arm/mach-msm/clock-pcom.c
+++ b/arch/arm/mach-msm/clock-pcom.c
@@ -1,6 +1,6 @@
 /*
  * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2007-2010, Code Aurora Forum. All rights reserved.
+ * Copyright (c) 2007-2012, The Linux Foundation. All rights reserved.
  *
  * This software is licensed under the terms of the GNU General Public
  * License version 2, as published by the Free Software Foundation, and
@@ -13,9 +13,12 @@
  *
  */
 
+#include <linux/kernel.h>
 #include <linux/err.h>
 #include <linux/platform_device.h>
 #include <linux/module.h>
+#include <linux/clk-provider.h>
+#include <linux/clkdev.h>
 
 #include <mach/clk.h>
 
@@ -23,11 +26,20 @@
 #include "clock.h"
 #include "clock-pcom.h"
 
-/*
- * glue for the proc_comm interface
- */
-static int pc_clk_enable(unsigned id)
+struct clk_pcom {
+	unsigned id;
+	unsigned long flags;
+	struct msm_clk msm_clk;
+};
+
+static inline struct clk_pcom *to_clk_pcom(struct clk_hw *hw)
 {
+	return container_of(to_msm_clk(hw), struct clk_pcom, msm_clk);
+}
+
+static int pc_clk_enable(struct clk_hw *hw)
+{
+	unsigned id = to_clk_pcom(hw)->id;
 	int rc = msm_proc_comm(PCOM_CLKCTL_RPC_ENABLE, &id, NULL);
 	if (rc < 0)
 		return rc;
@@ -35,14 +47,16 @@ static int pc_clk_enable(unsigned id)
 		return (int)id < 0 ? -EINVAL : 0;
 }
 
-static void pc_clk_disable(unsigned id)
+static void pc_clk_disable(struct clk_hw *hw)
 {
+	unsigned id = to_clk_pcom(hw)->id;
 	msm_proc_comm(PCOM_CLKCTL_RPC_DISABLE, &id, NULL);
 }
 
-int pc_clk_reset(unsigned id, enum clk_reset_action action)
+static int pc_clk_reset(struct clk_hw *hw, enum clk_reset_action action)
 {
 	int rc;
+	unsigned id = to_clk_pcom(hw)->id;
 
 	if (action == CLK_RESET_ASSERT)
 		rc = msm_proc_comm(PCOM_CLKCTL_RPC_RESET_ASSERT, &id, NULL);
@@ -55,83 +69,99 @@ int pc_clk_reset(unsigned id, enum clk_reset_action action)
 		return (int)id < 0 ? -EINVAL : 0;
 }
 
-static int pc_clk_set_rate(unsigned id, unsigned rate)
+static int pc_clk_set_rate(struct clk_hw *hw, unsigned long new_rate,
+			   unsigned long p_rate)
 {
-	/* The rate _might_ be rounded off to the nearest KHz value by the
+	struct clk_pcom *p = to_clk_pcom(hw);
+	unsigned id = p->id, rate = new_rate;
+	int rc;
+
+	/*
+	 * The rate _might_ be rounded off to the nearest KHz value by the
 	 * remote function. So a return value of 0 doesn't necessarily mean
 	 * that the exact rate was set successfully.
 	 */
-	int rc = msm_proc_comm(PCOM_CLKCTL_RPC_SET_RATE, &id, &rate);
-	if (rc < 0)
-		return rc;
-	else
-		return (int)id < 0 ? -EINVAL : 0;
-}
-
-static int pc_clk_set_min_rate(unsigned id, unsigned rate)
-{
-	int rc = msm_proc_comm(PCOM_CLKCTL_RPC_MIN_RATE, &id, &rate);
-	if (rc < 0)
-		return rc;
+	if (p->flags & CLKFLAG_MIN)
+		rc = msm_proc_comm(PCOM_CLKCTL_RPC_MIN_RATE, &id, &rate);
 	else
-		return (int)id < 0 ? -EINVAL : 0;
-}
-
-static int pc_clk_set_max_rate(unsigned id, unsigned rate)
-{
-	int rc = msm_proc_comm(PCOM_CLKCTL_RPC_MAX_RATE, &id, &rate);
+		rc = msm_proc_comm(PCOM_CLKCTL_RPC_SET_RATE, &id, &rate);
 	if (rc < 0)
 		return rc;
 	else
 		return (int)id < 0 ? -EINVAL : 0;
 }
 
-static unsigned pc_clk_get_rate(unsigned id)
+static unsigned long pc_clk_recalc_rate(struct clk_hw *hw, unsigned long p_rate)
 {
+	unsigned id = to_clk_pcom(hw)->id;
 	if (msm_proc_comm(PCOM_CLKCTL_RPC_RATE, &id, NULL))
 		return 0;
 	else
 		return id;
 }
 
-static unsigned pc_clk_is_enabled(unsigned id)
+static int pc_clk_is_enabled(struct clk_hw *hw)
 {
+	unsigned id = to_clk_pcom(hw)->id;
 	if (msm_proc_comm(PCOM_CLKCTL_RPC_ENABLED, &id, NULL))
 		return 0;
 	else
 		return id;
 }
 
-static long pc_clk_round_rate(unsigned id, unsigned rate)
+static long pc_clk_round_rate(struct clk_hw *hw, unsigned long rate,
+			      unsigned long *p_rate)
 {
-
 	/* Not really supported; pc_clk_set_rate() does rounding on it's own. */
 	return rate;
 }
 
-static bool pc_clk_is_local(unsigned id)
-{
-	return false;
-}
-
-struct clk_ops clk_ops_pcom = {
+static struct clk_ops clk_ops_pcom = {
 	.enable = pc_clk_enable,
 	.disable = pc_clk_disable,
-	.auto_off = pc_clk_disable,
-	.reset = pc_clk_reset,
 	.set_rate = pc_clk_set_rate,
-	.set_min_rate = pc_clk_set_min_rate,
-	.set_max_rate = pc_clk_set_max_rate,
-	.get_rate = pc_clk_get_rate,
+	.recalc_rate = pc_clk_recalc_rate,
 	.is_enabled = pc_clk_is_enabled,
 	.round_rate = pc_clk_round_rate,
-	.is_local = pc_clk_is_local,
 };
 
 static int msm_clock_pcom_probe(struct platform_device *pdev)
 {
 	const struct pcom_clk_pdata *pdata = pdev->dev.platform_data;
-	msm_clock_init(pdata->lookup, pdata->num_lookups);
+	int i, ret;
+
+	for (i = 0; i < pdata->num_lookups; i++) {
+		const struct clk_pcom_desc *desc = &pdata->lookup[i];
+		struct clk *c;
+		struct clk_pcom *p;
+		struct clk_hw *hw;
+		struct clk_init_data init;
+
+		p = devm_kzalloc(&pdev->dev, sizeof(*p), GFP_KERNEL);
+		if (!p)
+			return -ENOMEM;
+
+		p->id = desc->id;
+		p->flags = desc->flags;
+		p->msm_clk.reset = pc_clk_reset;
+
+		hw = &p->msm_clk.hw;
+		hw->init = &init;
+
+		init.name = desc->name;
+		init.ops = &clk_ops_pcom;
+		init.num_parents = 0;
+		init.flags = CLK_IS_ROOT;
+
+		if (!(p->flags & CLKFLAG_AUTO_OFF))
+			init.flags |= CLK_IGNORE_UNUSED;
+
+		c = devm_clk_register(&pdev->dev, hw);
+		ret = clk_register_clkdev(c, desc->con, desc->dev);
+		if (ret)
+			return ret;
+	}
+
 	return 0;
 }
 
diff --git a/arch/arm/mach-msm/clock-pcom.h b/arch/arm/mach-msm/clock-pcom.h
index 87406a3..5bb164f 100644
--- a/arch/arm/mach-msm/clock-pcom.h
+++ b/arch/arm/mach-msm/clock-pcom.h
@@ -1,4 +1,5 @@
-/* Copyright (c) 2009, Code Aurora Forum. All rights reserved.
+/*
+ * Copyright (c) 2009-2012, The Linux Foundation. All rights reserved.
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 and
@@ -120,26 +121,25 @@
 
 #define P_NR_CLKS		102
 
-struct clk_ops;
-extern struct clk_ops clk_ops_pcom;
+struct clk_pcom_desc {
+	unsigned id;
+	const char *name;
+	const char *con;
+	const char *dev;
+	unsigned long flags;
+};
 
 struct pcom_clk_pdata {
-	struct clk_lookup *lookup;
+	struct clk_pcom_desc *lookup;
 	u32 num_lookups;
 };
 
-int pc_clk_reset(unsigned id, enum clk_reset_action action);
-
 #define CLK_PCOM(clk_name, clk_id, clk_dev, clk_flags) {	\
-	.con_id = clk_name, \
-	.dev_id = clk_dev, \
-	.clk = &(struct clk){ \
-		.id = P_##clk_id, \
-		.remote_id = P_##clk_id, \
-		.ops = &clk_ops_pcom, \
-		.flags = clk_flags, \
-		.dbg_name = #clk_id, \
-	}, \
+	.id = P_##clk_id,					\
+	.name = #clk_id,					\
+	.con = clk_name,					\
+	.dev = clk_dev,						\
+	.flags = clk_flags,					\
 	}
 
 #endif
diff --git a/arch/arm/mach-msm/clock.c b/arch/arm/mach-msm/clock.c
index 01af7a4..35ea02b 100644
--- a/arch/arm/mach-msm/clock.c
+++ b/arch/arm/mach-msm/clock.c
@@ -1,7 +1,7 @@
 /* arch/arm/mach-msm/clock.c
  *
  * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2007-2010, Code Aurora Forum. All rights reserved.
+ * Copyright (c) 2007-2012, The Linux Foundation. All rights reserved.
  *
  * This software is licensed under the terms of the GNU General Public
  * License version 2, as published by the Free Software Foundation, and
@@ -14,151 +14,15 @@
  *
  */
 
-#include <linux/kernel.h>
-#include <linux/list.h>
-#include <linux/err.h>
-#include <linux/spinlock.h>
-#include <linux/pm_qos.h>
-#include <linux/mutex.h>
-#include <linux/clk.h>
-#include <linux/string.h>
+#include <linux/clk-provider.h>
 #include <linux/module.h>
-#include <linux/clkdev.h>
 
 #include "clock.h"
 
-static DEFINE_MUTEX(clocks_mutex);
-static DEFINE_SPINLOCK(clocks_lock);
-static LIST_HEAD(clocks);
-
-/*
- * Standard clock functions defined in include/linux/clk.h
- */
-int clk_enable(struct clk *clk)
-{
-	unsigned long flags;
-	spin_lock_irqsave(&clocks_lock, flags);
-	clk->count++;
-	if (clk->count == 1)
-		clk->ops->enable(clk->id);
-	spin_unlock_irqrestore(&clocks_lock, flags);
-	return 0;
-}
-EXPORT_SYMBOL(clk_enable);
-
-void clk_disable(struct clk *clk)
-{
-	unsigned long flags;
-	spin_lock_irqsave(&clocks_lock, flags);
-	BUG_ON(clk->count == 0);
-	clk->count--;
-	if (clk->count == 0)
-		clk->ops->disable(clk->id);
-	spin_unlock_irqrestore(&clocks_lock, flags);
-}
-EXPORT_SYMBOL(clk_disable);
-
 int clk_reset(struct clk *clk, enum clk_reset_action action)
 {
-	return clk->ops->reset(clk->remote_id, action);
+	struct clk_hw *hw = __clk_get_hw(clk);
+	struct msm_clk *m = to_msm_clk(hw);
+	return m->reset(hw, action);
 }
 EXPORT_SYMBOL(clk_reset);
-
-unsigned long clk_get_rate(struct clk *clk)
-{
-	return clk->ops->get_rate(clk->id);
-}
-EXPORT_SYMBOL(clk_get_rate);
-
-int clk_set_rate(struct clk *clk, unsigned long rate)
-{
-	int ret;
-	if (clk->flags & CLKFLAG_MAX) {
-		ret = clk->ops->set_max_rate(clk->id, rate);
-		if (ret)
-			return ret;
-	}
-	if (clk->flags & CLKFLAG_MIN) {
-		ret = clk->ops->set_min_rate(clk->id, rate);
-		if (ret)
-			return ret;
-	}
-
-	if (clk->flags & CLKFLAG_MAX || clk->flags & CLKFLAG_MIN)
-		return ret;
-
-	return clk->ops->set_rate(clk->id, rate);
-}
-EXPORT_SYMBOL(clk_set_rate);
-
-long clk_round_rate(struct clk *clk, unsigned long rate)
-{
-	return clk->ops->round_rate(clk->id, rate);
-}
-EXPORT_SYMBOL(clk_round_rate);
-
-int clk_set_parent(struct clk *clk, struct clk *parent)
-{
-	return -ENOSYS;
-}
-EXPORT_SYMBOL(clk_set_parent);
-
-struct clk *clk_get_parent(struct clk *clk)
-{
-	return ERR_PTR(-ENOSYS);
-}
-EXPORT_SYMBOL(clk_get_parent);
-
-/* EBI1 is the only shared clock that several clients want to vote on as of
- * this commit. If this changes in the future, then it might be better to
- * make clk_min_rate handle the voting or make ebi1_clk_set_min_rate more
- * generic to support different clocks.
- */
-static struct clk *ebi1_clk;
-
-void msm_clock_init(struct clk_lookup *clock_tbl, size_t num_clocks)
-{
-	unsigned n;
-
-	mutex_lock(&clocks_mutex);
-	for (n = 0; n < num_clocks; n++) {
-		clkdev_add(&clock_tbl[n]);
-		list_add_tail(&clock_tbl[n].clk->list, &clocks);
-	}
-	mutex_unlock(&clocks_mutex);
-
-	ebi1_clk = clk_get(NULL, "ebi1_clk");
-	BUG_ON(ebi1_clk == NULL);
-
-}
-
-/* The bootloader and/or AMSS may have left various clocks enabled.
- * Disable any clocks that belong to us (CLKFLAG_AUTO_OFF) but have
- * not been explicitly enabled by a clk_enable() call.
- */
-static int __init clock_late_init(void)
-{
-	unsigned long flags;
-	struct clk *clk;
-	unsigned count = 0;
-
-	clock_debug_init();
-	mutex_lock(&clocks_mutex);
-	list_for_each_entry(clk, &clocks, list) {
-		clock_debug_add(clk);
-		if (clk->flags & CLKFLAG_AUTO_OFF) {
-			spin_lock_irqsave(&clocks_lock, flags);
-			if (!clk->count) {
-				count++;
-				clk->ops->auto_off(clk->id);
-			}
-			spin_unlock_irqrestore(&clocks_lock, flags);
-		}
-	}
-	mutex_unlock(&clocks_mutex);
-	pr_info("clock_late_init() disabled %d unused clocks\n", count);
-	return 0;
-}
-
-late_initcall(clock_late_init);
-
diff --git a/arch/arm/mach-msm/clock.h b/arch/arm/mach-msm/clock.h
index cc76bfe..42d29dd 100644
--- a/arch/arm/mach-msm/clock.h
+++ b/arch/arm/mach-msm/clock.h
@@ -1,7 +1,7 @@
 /* arch/arm/mach-msm/clock.h
  *
  * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2007-2010, Code Aurora Forum. All rights reserved.
+ * Copyright (c) 2007-2012, The Linux Foundation. All rights reserved.
  *
  * This software is licensed under the terms of the GNU General Public
  * License version 2, as published by the Free Software Foundation, and
@@ -17,8 +17,7 @@
 #ifndef __ARCH_ARM_MACH_MSM_CLOCK_H
 #define __ARCH_ARM_MACH_MSM_CLOCK_H
 
-#include <linux/init.h>
-#include <linux/list.h>
+#include <linux/clk-provider.h>
 #include <mach/clk.h>
 
 #define CLK_FIRST_AVAILABLE_FLAG	0x00000100
@@ -26,44 +25,19 @@
 #define CLKFLAG_MIN			0x00000400
 #define CLKFLAG_MAX			0x00000800
 
-struct clk_ops {
-	int (*enable)(unsigned id);
-	void (*disable)(unsigned id);
-	void (*auto_off)(unsigned id);
-	int (*reset)(unsigned id, enum clk_reset_action action);
-	int (*set_rate)(unsigned id, unsigned rate);
-	int (*set_min_rate)(unsigned id, unsigned rate);
-	int (*set_max_rate)(unsigned id, unsigned rate);
-	unsigned (*get_rate)(unsigned id);
-	unsigned (*is_enabled)(unsigned id);
-	long (*round_rate)(unsigned id, unsigned rate);
-	bool (*is_local)(unsigned id);
-};
-
-struct clk {
-	uint32_t id;
-	uint32_t remote_id;
-	uint32_t count;
-	uint32_t flags;
-	struct clk_ops *ops;
-	const char *dbg_name;
-	struct list_head list;
-};
-
 #define OFF CLKFLAG_AUTO_OFF
 #define CLK_MIN CLKFLAG_MIN
 #define CLK_MAX CLKFLAG_MAX
 #define CLK_MINMAX (CLK_MIN | CLK_MAX)
 
-#ifdef CONFIG_DEBUG_FS
-int __init clock_debug_init(void);
-int __init clock_debug_add(struct clk *clock);
-#else
-static inline int __init clock_debug_init(void) { return 0; }
-static inline int __init clock_debug_add(struct clk *clock) { return 0; }
-#endif
+struct msm_clk {
+	int (*reset)(struct clk_hw *hw, enum clk_reset_action action);
+	struct clk_hw hw;
+};
 
-struct clk_lookup;
-void msm_clock_init(struct clk_lookup *clock_tbl, size_t num_clocks);
+static inline struct msm_clk *to_msm_clk(struct clk_hw *hw)
+{
+	return container_of(hw, struct msm_clk, hw);
+}
 
 #endif
diff --git a/arch/arm/mach-msm/devices-msm7x00.c b/arch/arm/mach-msm/devices-msm7x00.c
index 9edfe68..6d50fb9 100644
--- a/arch/arm/mach-msm/devices-msm7x00.c
+++ b/arch/arm/mach-msm/devices-msm7x00.c
@@ -425,7 +425,7 @@ struct platform_device msm_device_mdp = {
 	.resource = resources_mdp,
 };
 
-static struct clk_lookup msm_clocks_7x01a[] = {
+static struct clk_pcom_desc msm_clocks_7x01a[] = {
 	CLK_PCOM("adm_clk",	ADM_CLK,	NULL, 0),
 	CLK_PCOM("adsp_clk",	ADSP_CLK,	NULL, 0),
 	CLK_PCOM("ebi1_clk",	EBI1_CLK,	NULL, 0),
diff --git a/arch/arm/mach-msm/devices-msm7x30.c b/arch/arm/mach-msm/devices-msm7x30.c
index e877fd6..be45136 100644
--- a/arch/arm/mach-msm/devices-msm7x30.c
+++ b/arch/arm/mach-msm/devices-msm7x30.c
@@ -160,7 +160,7 @@ struct platform_device msm_device_hsusb_host = {
 	},
 };
 
-static struct clk_lookup msm_clocks_7x30[] = {
+static struct clk_pcom_desc msm_clocks_7x30[] = {
 	CLK_PCOM("adm_clk",	ADM_CLK,	NULL, 0),
 	CLK_PCOM("adsp_clk",	ADSP_CLK,	NULL, 0),
 	CLK_PCOM("cam_m_clk",	CAM_M_CLK,	NULL, 0),
diff --git a/arch/arm/mach-msm/devices-qsd8x50.c b/arch/arm/mach-msm/devices-qsd8x50.c
index a62f647..3fd8f88 100644
--- a/arch/arm/mach-msm/devices-qsd8x50.c
+++ b/arch/arm/mach-msm/devices-qsd8x50.c
@@ -322,7 +322,7 @@ int __init msm_add_sdcc(unsigned int controller,
 	return platform_device_register(pdev);
 }
 
-static struct clk_lookup msm_clocks_8x50[] = {
+static struct clk_pcom_desc msm_clocks_8x50[] = {
 	CLK_PCOM("adm_clk",	ADM_CLK,	NULL, 0),
 	CLK_PCOM("ce_clk",	CE_CLK,		NULL, 0),
 	CLK_PCOM("ebi1_clk",	EBI1_CLK,	NULL, CLK_MIN),
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation

Re: [PATCH/RESEND 00/12] Convert MSM to common clock framework

[Stephen Boyd]

On 06/17, Stephen Boyd wrote:
> Resending to collect higher level maintainer acks per Olof's request. 
> The plan is to push this patchset through MSM to the arm-soc tree.
> 
> This patchset moves the existing MSM clock code and affected drivers to the
> common clock framework. A prerequisite of moving to the common clock
> framework is to use clk_prepare() and clk_enable() so the first
> few patches migrate drivers to that call (clk_prepare() is a no-op on MSM
> right now). It also removes some custom clock APIs that MSM provides
> and finally moves the proc_comm clock code to the common struct clk.
> 
> This patch series will be used as the foundation of the MSM 8660/8960
> clock code that I plan to send out after this series.
> 

David, can you pick this up and send it off to arm-soc now?

-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation

Re: [PATCH/RESEND 00/12] Convert MSM to common clock framework

[David Brown]

On Thu, Jun 20, 2013 at 06:29:52PM -0700, Stephen Boyd wrote:
>On 06/17, Stephen Boyd wrote:
>> Resending to collect higher level maintainer acks per Olof's request.
>> The plan is to push this patchset through MSM to the arm-soc tree.
>>
>> This patchset moves the existing MSM clock code and affected drivers to the
>> common clock framework. A prerequisite of moving to the common clock
>> framework is to use clk_prepare() and clk_enable() so the first
>> few patches migrate drivers to that call (clk_prepare() is a no-op on MSM
>> right now). It also removes some custom clock APIs that MSM provides
>> and finally moves the proc_comm clock code to the common struct clk.
>>
>> This patch series will be used as the foundation of the MSM 8660/8960
>> clock code that I plan to send out after this series.
>>
>
>David, can you pick this up and send it off to arm-soc now?

I'm still not seeing an Ack from

  msm_sdcc: Convert to clk_prepare/unprepare

Thanks,
David

-- 
sent by an employee of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation