[PATCH v2 0/7] Add MDIO bus multiplexer support for iProc SoCs

[PATCH v2 0/7] Add MDIO bus multiplexer support for iProc SoCs

[Pramod Kumar]

Broadcom iProc based SoCs use a MDIO bus multiplexer where child buses
could be internal as well external to SoCs. These buses could supports
MDIO transaction compatible to C-22/C-45.

Broadcom MDIO bus mulitplexer is an integrated multiplexer where child bus
selection and mdio transaction logic lies inside multiplexer itself.
To accommodate this multiplexer in existing mux framework below changes
were required-

1. Passed MDIO parent bus via mdio_mux_init to MDIO mux framework.

2. Defined one new boolean property named "mdio-integrated-mux". Integrated
   bus Multiplexer node defines this so when parent bus is registered
   by calling "of_mdiobus_register", this api will not scan for child
   nodes. Child node of integrated multiplexer will be muxed nodes not
   PHYs one hence should not be scanned.

This patch set includes MDIO bus multiplexer driver along with above
framework changes. It includes one external bus node having Ethernet PHY
attached and two internal bus node holding PCIe PHYs.

This patch series is based on v4.6.0-rc1 and is available from github-
repo: https://github.com/Broadcom/arm64-linux.git
branch:mdio-mux-v2

Changes from v1:
- stop using "brcm,is_c45" from bus node as suggested by Andrew. MDIO
PHY driver will logically OR MII_ADDR_C45 into the address when issues
any C45 MDIO read/write transaction.

Pramod Kumar (7):
  mdio:mux: Enhanced MDIO mux framework for integrated multiplexers
  DT: phy.txt: Add mdio-integrated-mux property
  binding: mdio-mux: Add DT binding doc for Broadcom MDIO bus mutiplexer
  DT:mdio-mux: Add mdio multiplexer driver node
  net:mdio-mux: Add MDIO mux driver for iProc SoCs
  Binding:PHY: Binding doc for NS2 PCIe PHYs.
  phy: Add Northstar2 PCI Phy support

 .../bindings/net/brcm,mdio-mux-iproc.txt           |  60 +++++
 Documentation/devicetree/bindings/net/mdio-mux.txt |   9 +-
 .../bindings/phy/brcm,mdio-mux-bus-pci.txt         |  27 +++
 arch/arm64/boot/dts/broadcom/ns2-svk.dts           |  12 +
 arch/arm64/boot/dts/broadcom/ns2.dtsi              |  32 +++
 drivers/net/phy/Kconfig                            |  11 +
 drivers/net/phy/Makefile                           |   1 +
 drivers/net/phy/mdio-mux-bcm-iproc.c               | 243 +++++++++++++++++++++
 drivers/net/phy/mdio-mux-gpio.c                    |   2 +-
 drivers/net/phy/mdio-mux-mmioreg.c                 |   2 +-
 drivers/net/phy/mdio-mux.c                         |  28 ++-
 drivers/of/of_mdio.c                               |   3 +
 drivers/phy/Kconfig                                |   8 +
 drivers/phy/Makefile                               |   1 +
 drivers/phy/phy-bcm-ns2-pcie.c                     | 115 ++++++++++
 include/linux/mdio-mux.h                           |   4 +-
 16 files changed, 544 insertions(+), 14 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt
 create mode 100644 Documentation/devicetree/bindings/phy/brcm,mdio-mux-bus-pci.txt
 create mode 100644 drivers/net/phy/mdio-mux-bcm-iproc.c
 create mode 100644 drivers/phy/phy-bcm-ns2-pcie.c

-- 
1.9.1

[PATCH v2 1/7] mdio:mux: Enhanced MDIO mux framework for integrated multiplexers

[Pramod Kumar]

An integrated multiplexer uses same address space for
"muxed bus selection" and "generation of mdio transaction"
hence its good to register parent bus from mux driver.

Hence added a mechanism where mux driver could register a
parent bus and pass it down to framework via mdio_mux_init api.

Below changes are required to make this happen-

1. When mdio-mux parent bus is registered, mdio framework should not
parse for child as it will be muxed bus node not PHYs.

-created a new property "mdio-mux-bus-parent". if this property is present,
of_mdiobus_register will not scan for phys.

2. Passed down parent bus to mdio mux framework via mdio-mux-init api.

Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
---
 drivers/net/phy/mdio-mux-gpio.c    |  2 +-
 drivers/net/phy/mdio-mux-mmioreg.c |  2 +-
 drivers/net/phy/mdio-mux.c         | 28 ++++++++++++++++++----------
 drivers/of/of_mdio.c               |  3 +++
 include/linux/mdio-mux.h           |  4 +++-
 5 files changed, 26 insertions(+), 13 deletions(-)

diff --git a/drivers/net/phy/mdio-mux-gpio.c b/drivers/net/phy/mdio-mux-gpio.c
index 7ddb1ab..9199499 100644
--- a/drivers/net/phy/mdio-mux-gpio.c
+++ b/drivers/net/phy/mdio-mux-gpio.c
@@ -55,7 +55,7 @@ static int mdio_mux_gpio_probe(struct platform_device *pdev)
 		return PTR_ERR(s->gpios);
 
 	r = mdio_mux_init(&pdev->dev,
-			  mdio_mux_gpio_switch_fn, &s->mux_handle, s);
+			  mdio_mux_gpio_switch_fn, &s->mux_handle, s, NULL);
 
 	if (r != 0) {
 		gpiod_put_array(s->gpios);
diff --git a/drivers/net/phy/mdio-mux-mmioreg.c b/drivers/net/phy/mdio-mux-mmioreg.c
index 7fde454..d0bed52 100644
--- a/drivers/net/phy/mdio-mux-mmioreg.c
+++ b/drivers/net/phy/mdio-mux-mmioreg.c
@@ -126,7 +126,7 @@ static int mdio_mux_mmioreg_probe(struct platform_device *pdev)
 	}
 
 	ret = mdio_mux_init(&pdev->dev, mdio_mux_mmioreg_switch_fn,
-			    &s->mux_handle, s);
+			    &s->mux_handle, s, NULL);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to register mdio-mux bus %s\n",
 			np->full_name);
diff --git a/drivers/net/phy/mdio-mux.c b/drivers/net/phy/mdio-mux.c
index 308ade0..521ab90 100644
--- a/drivers/net/phy/mdio-mux.c
+++ b/drivers/net/phy/mdio-mux.c
@@ -95,7 +95,8 @@ static int parent_count;
 int mdio_mux_init(struct device *dev,
 		  int (*switch_fn)(int cur, int desired, void *data),
 		  void **mux_handle,
-		  void *data)
+		  void *data,
+		  struct mii_bus *mux_bus)
 {
 	struct device_node *parent_bus_node;
 	struct device_node *child_bus_node;
@@ -107,10 +108,21 @@ int mdio_mux_init(struct device *dev,
 	if (!dev->of_node)
 		return -ENODEV;
 
-	parent_bus_node = of_parse_phandle(dev->of_node, "mdio-parent-bus", 0);
+	if (!mux_bus) {
+		parent_bus_node = of_parse_phandle(dev->of_node,
+						   "mdio-parent-bus", 0);
 
-	if (!parent_bus_node)
-		return -ENODEV;
+		if (!parent_bus_node)
+			return -ENODEV;
+
+		parent_bus = of_mdio_find_bus(parent_bus_node);
+		if (!parent_bus) {
+			ret_val = -EPROBE_DEFER;
+			goto err_parent_bus;
+		}
+	} else {
+		parent_bus = mux_bus;
+	}
 
 	pb = devm_kzalloc(dev, sizeof(*pb), GFP_KERNEL);
 	if (pb == NULL) {
@@ -118,11 +130,6 @@ int mdio_mux_init(struct device *dev,
 		goto err_parent_bus;
 	}
 
-	parent_bus = of_mdio_find_bus(parent_bus_node);
-	if (parent_bus == NULL) {
-		ret_val = -EPROBE_DEFER;
-		goto err_parent_bus;
-	}
 
 	pb->switch_data = data;
 	pb->switch_fn = switch_fn;
@@ -183,7 +190,8 @@ int mdio_mux_init(struct device *dev,
 	put_device(&pb->mii_bus->dev);
 
 err_parent_bus:
-	of_node_put(parent_bus_node);
+	if (!mux_bus)
+		of_node_put(parent_bus_node);
 	return ret_val;
 }
 EXPORT_SYMBOL_GPL(mdio_mux_init);
diff --git a/drivers/of/of_mdio.c b/drivers/of/of_mdio.c
index 8453f08..cf40e7a 100644
--- a/drivers/of/of_mdio.c
+++ b/drivers/of/of_mdio.c
@@ -225,6 +225,9 @@ int of_mdiobus_register(struct mii_bus *mdio, struct device_node *np)
 	if (rc)
 		return rc;
 
+	if (of_property_read_bool(np, "mdio-integrated-mux"))
+		return 0;
+
 	/* Loop over the child nodes and register a phy_device for each phy */
 	for_each_available_child_of_node(np, child) {
 		addr = of_mdio_parse_addr(&mdio->dev, child);
diff --git a/include/linux/mdio-mux.h b/include/linux/mdio-mux.h
index a243dbb..61f5b21 100644
--- a/include/linux/mdio-mux.h
+++ b/include/linux/mdio-mux.h
@@ -10,11 +10,13 @@
 #ifndef __LINUX_MDIO_MUX_H
 #define __LINUX_MDIO_MUX_H
 #include <linux/device.h>
+#include <linux/phy.h>
 
 int mdio_mux_init(struct device *dev,
 		  int (*switch_fn) (int cur, int desired, void *data),
 		  void **mux_handle,
-		  void *data);
+		  void *data,
+		  struct mii_bus *mux_bus);
 
 void mdio_mux_uninit(void *mux_handle);
 
-- 
1.9.1

Re: [PATCH v2 1/7] mdio:mux: Enhanced MDIO mux framework for integrated multiplexers

[Andrew Lunn]

> diff --git a/drivers/of/of_mdio.c b/drivers/of/of_mdio.c
> index 8453f08..cf40e7a 100644
> --- a/drivers/of/of_mdio.c
> +++ b/drivers/of/of_mdio.c
> @@ -225,6 +225,9 @@ int of_mdiobus_register(struct mii_bus *mdio, struct device_node *np)
>  	if (rc)
>  		return rc;
>  
> +	if (of_property_read_bool(np, "mdio-integrated-mux"))
> +		return 0;
> +

Hi

Rather than doing this, did you try setting bus->phy_mask = 0 and
calling mdiobus_register(), rather than of_mdiobus_regsiter() for the
parent bus?

	Andrew

RE: [PATCH v2 1/7] mdio:mux: Enhanced MDIO mux framework for integrated multiplexers

[Pramod Kumar]

Hi Andrew,

> -----Original Message-----
> From: Andrew Lunn [mailto:andrew@lunn.ch]
> Sent: 01 June 2016 18:32
> To: Pramod Kumar
> Cc: Rob Herring; Pawel Moll; Mark Rutland; Ian Campbell; Kumar Gala;
Catalin
> Marinas; Will Deacon; Kishon Vijay Abraham I; David S. Miller;
> devicetree@vger.kernel.org; netdev@vger.kernel.org; linux-
> kernel@vger.kernel.org; bcm-kernel-feedback-list@broadcom.com;
linux-arm-
> kernel@lists.infradead.org
> Subject: Re: [PATCH v2 1/7] mdio:mux: Enhanced MDIO mux framework for
> integrated multiplexers
>
> > diff --git a/drivers/of/of_mdio.c b/drivers/of/of_mdio.c index
> > 8453f08..cf40e7a 100644
> > --- a/drivers/of/of_mdio.c
> > +++ b/drivers/of/of_mdio.c
> > @@ -225,6 +225,9 @@ int of_mdiobus_register(struct mii_bus *mdio,
struct
> device_node *np)
> >  	if (rc)
> >  		return rc;
> >
> > +	if (of_property_read_bool(np, "mdio-integrated-mux"))
> > +		return 0;
> > +
>
> Hi
>
> Rather than doing this, did you try setting bus->phy_mask = 0 and
calling
> mdiobus_register(), rather than of_mdiobus_regsiter() for the parent
bus?
>

After setting bus->phy_mask = ~0 and using mdiobus_regsiter() I could get
rid of newly added
Property. It works for me as I find same has been done inside of
of_mdiobus_regsiter().

Thanks for pointing out this.

> 	Andrew

[PATCH v2 2/7] DT: phy.txt: Add mdio-integrated-mux property

[Pramod Kumar]

This property is used by integrated MDIO multiplexer
which has bus selection and mdio transaction generation logic,
integrated inside.

Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
---
 Documentation/devicetree/bindings/net/mdio-mux.txt | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/net/mdio-mux.txt b/Documentation/devicetree/bindings/net/mdio-mux.txt
index 491f5bd..b5ad83e 100644
--- a/Documentation/devicetree/bindings/net/mdio-mux.txt
+++ b/Documentation/devicetree/bindings/net/mdio-mux.txt
@@ -5,13 +5,20 @@ numbered uniquely in a device dependent manner.  The nodes for an MDIO
 bus multiplexer/switch will have one child node for each child bus.
 
 Required properties:
-- mdio-parent-bus : phandle to the parent MDIO bus.
 - #address-cells = <1>;
 - #size-cells = <0>;
 
 Optional properties:
+- mdio-parent-bus : phandle to the parent MDIO bus. Should be used
+		if parent mdio bus is not part of multiplexer.
+- mdio-integrated-mux: boolean property indicateing that the hardware
+		is an integrated multiplex supporting muxed bus selection
+		and MDIO transaction logic generation.
 - Other properties specific to the multiplexer/switch hardware.
 
+Note: one of mdio-parent-bus and mdio-integrated-mux is mandatory to
+get parent bus regsitered.
+
 Required properties for child nodes:
 - #address-cells = <1>;
 - #size-cells = <0>;
-- 
1.9.1

Re: [PATCH v2 2/7] DT: phy.txt: Add mdio-integrated-mux property

[Rob Herring]

On Tue, May 31, 2016 at 07:06:36PM +0530, Pramod Kumar wrote:
> This property is used by integrated MDIO multiplexer
> which has bus selection and mdio transaction generation logic,
> integrated inside.
> 
> Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
> ---
>  Documentation/devicetree/bindings/net/mdio-mux.txt | 9 ++++++++-
>  1 file changed, 8 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/net/mdio-mux.txt b/Documentation/devicetree/bindings/net/mdio-mux.txt
> index 491f5bd..b5ad83e 100644
> --- a/Documentation/devicetree/bindings/net/mdio-mux.txt
> +++ b/Documentation/devicetree/bindings/net/mdio-mux.txt
> @@ -5,13 +5,20 @@ numbered uniquely in a device dependent manner.  The nodes for an MDIO
>  bus multiplexer/switch will have one child node for each child bus.
>  
>  Required properties:
> -- mdio-parent-bus : phandle to the parent MDIO bus.
>  - #address-cells = <1>;
>  - #size-cells = <0>;
>  
>  Optional properties:
> +- mdio-parent-bus : phandle to the parent MDIO bus. Should be used
> +		if parent mdio bus is not part of multiplexer.

You don't appear to be using this. When would you?

> +- mdio-integrated-mux: boolean property indicateing that the hardware
> +		is an integrated multiplex supporting muxed bus selection
> +		and MDIO transaction logic generation.
>  - Other properties specific to the multiplexer/switch hardware.
>  
> +Note: one of mdio-parent-bus and mdio-integrated-mux is mandatory to
> +get parent bus regsitered.
> +
>  Required properties for child nodes:
>  - #address-cells = <1>;
>  - #size-cells = <0>;
> -- 
> 1.9.1
> 

Re: [PATCH v2 2/7] DT: phy.txt: Add mdio-integrated-mux property

[Andrew Lunn]

On Thu, Jun 02, 2016 at 06:27:03PM -0500, Rob Herring wrote:
> On Tue, May 31, 2016 at 07:06:36PM +0530, Pramod Kumar wrote:
> > This property is used by integrated MDIO multiplexer
> > which has bus selection and mdio transaction generation logic,
> > integrated inside.
> > 
> > Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
> > ---
> >  Documentation/devicetree/bindings/net/mdio-mux.txt | 9 ++++++++-
> >  1 file changed, 8 insertions(+), 1 deletion(-)
> > 
> > diff --git a/Documentation/devicetree/bindings/net/mdio-mux.txt b/Documentation/devicetree/bindings/net/mdio-mux.txt
> > index 491f5bd..b5ad83e 100644
> > --- a/Documentation/devicetree/bindings/net/mdio-mux.txt
> > +++ b/Documentation/devicetree/bindings/net/mdio-mux.txt
> > @@ -5,13 +5,20 @@ numbered uniquely in a device dependent manner.  The nodes for an MDIO
> >  bus multiplexer/switch will have one child node for each child bus.
> >  
> >  Required properties:
> > -- mdio-parent-bus : phandle to the parent MDIO bus.
> >  - #address-cells = <1>;
> >  - #size-cells = <0>;
> >  
> >  Optional properties:
> > +- mdio-parent-bus : phandle to the parent MDIO bus. Should be used
> > +		if parent mdio bus is not part of multiplexer.
> 
> You don't appear to be using this. When would you?

He is moving it to optional. The mdio-mux-mmio and mdio-mux-gpio do
however use it, which follow this binding.

	Andrew

[PATCH v2 3/7] binding: mdio-mux: Add DT binding doc for Broadcom MDIO bus mutiplexer

[Pramod Kumar]

Add DT binding doc for Broadcom MDIO bus mutiplexer driver.

Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
---
 .../bindings/net/brcm,mdio-mux-iproc.txt           | 60 ++++++++++++++++++++++
 1 file changed, 60 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt

diff --git a/Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt b/Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt
new file mode 100644
index 0000000..f270b41
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt
@@ -0,0 +1,60 @@
+Properties for an MDIO bus mutiplexer found in Broadcom iProc based SoCs.
+
+This MDIO bus multiplexer defines buses that could be internal as well as
+external to SoCs and could accept MDIO transaction compatible to C-22 or
+C-45 Clause. When Child bus is selected, one need to select these two
+properties as well to generate desired MDIO trascation on appropriate bus.
+
+Required properties in addition to the generic multiplexer properties:
+
+MDIO multiplexer node:
+- complatible: brcm,mdio-mux-iproc.
+
+Every non-ethernet PHY requires a compatible so that it could be probed based
+on this compatible string.
+
+Additional information regarding generic multiplexer properties could be found
+at- Documentation/devicetree/bindings/net/mdio-mux.txt
+
+
+for example:
+		mdio_mux_iproc: mdio_mux_iproc@6602023c {
+			compatible = "brcm,mdio-mux-iproc";
+			reg = <0x6602023c 0x14>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			mdio-integrated-mux;
+
+			mdio@0 {
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				pci_phy0: pci-phy@0 {
+					compatible = "brcm,ns2-pcie-phy";
+					reg = <0x0>;
+					#phy-cells = <0>;
+				};
+			};
+
+			mdio@7 {
+				reg = <0x7>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				pci_phy1: pci-phy@0 {
+					compatible = "brcm,ns2-pcie-phy";
+					reg = <0x0>;
+					#phy-cells = <0>;
+				};
+			};
+			mdio@10 {
+				reg = <0x10>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gphy0: eth-phy@10 {
+					reg = <0x10>;
+				};
+			};
+		};
-- 
1.9.1

Re: [PATCH v2 3/7] binding: mdio-mux: Add DT binding doc for Broadcom MDIO bus mutiplexer

[Rob Herring]

On Tue, May 31, 2016 at 07:06:37PM +0530, Pramod Kumar wrote:
> Add DT binding doc for Broadcom MDIO bus mutiplexer driver.
> 
> Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
> ---
>  .../bindings/net/brcm,mdio-mux-iproc.txt           | 60 ++++++++++++++++++++++
>  1 file changed, 60 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt
> 
> diff --git a/Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt b/Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt
> new file mode 100644
> index 0000000..f270b41
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt
> @@ -0,0 +1,60 @@
> +Properties for an MDIO bus mutiplexer found in Broadcom iProc based SoCs.
> +
> +This MDIO bus multiplexer defines buses that could be internal as well as
> +external to SoCs and could accept MDIO transaction compatible to C-22 or
> +C-45 Clause. When Child bus is selected, one need to select these two

s/Child/child/

s/need/needs/

> +properties as well to generate desired MDIO trascation on appropriate bus.
> +
> +Required properties in addition to the generic multiplexer properties:
> +
> +MDIO multiplexer node:
> +- complatible: brcm,mdio-mux-iproc.

typo

> +
> +Every non-ethernet PHY requires a compatible so that it could be probed based
> +on this compatible string.
> +
> +Additional information regarding generic multiplexer properties could be found

s/could/can/

> +at- Documentation/devicetree/bindings/net/mdio-mux.txt
> +
> +
> +for example:
> +		mdio_mux_iproc: mdio_mux_iproc@6602023c {

No '_' in node names.

mdio-mux@...

> +			compatible = "brcm,mdio-mux-iproc";
> +			reg = <0x6602023c 0x14>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			mdio-integrated-mux;
> +
> +			mdio@0 {
> +				reg = <0x0>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				pci_phy0: pci-phy@0 {
> +					compatible = "brcm,ns2-pcie-phy";
> +					reg = <0x0>;
> +					#phy-cells = <0>;
> +				};
> +			};
> +
> +			mdio@7 {
> +				reg = <0x7>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				pci_phy1: pci-phy@0 {
> +					compatible = "brcm,ns2-pcie-phy";
> +					reg = <0x0>;
> +					#phy-cells = <0>;
> +				};
> +			};
> +			mdio@10 {
> +				reg = <0x10>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				gphy0: eth-phy@10 {
> +					reg = <0x10>;
> +				};
> +			};
> +		};
> -- 
> 1.9.1
> 

RE: [PATCH v2 3/7] binding: mdio-mux: Add DT binding doc for Broadcom MDIO bus mutiplexer

[Pramod Kumar]

Hi Rob,

> -----Original Message-----
> From: Rob Herring [mailto:robh@kernel.org]
> Sent: 03 June 2016 07:13
> To: Pramod Kumar
> Cc: Pawel Moll; Mark Rutland; Ian Campbell; Kumar Gala; Catalin Marinas;
Will
> Deacon; Kishon Vijay Abraham I; David S. Miller;
devicetree@vger.kernel.org;
> linux-arm-kernel@lists.infradead.org; bcm-kernel-feedback-
> list@broadcom.com; linux-kernel@vger.kernel.org; netdev@vger.kernel.org
> Subject: Re: [PATCH v2 3/7] binding: mdio-mux: Add DT binding doc for
> Broadcom MDIO bus mutiplexer
>
> On Tue, May 31, 2016 at 07:06:37PM +0530, Pramod Kumar wrote:
> > Add DT binding doc for Broadcom MDIO bus mutiplexer driver.
> >
> > Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
> > ---
> >  .../bindings/net/brcm,mdio-mux-iproc.txt           | 60
> ++++++++++++++++++++++
> >  1 file changed, 60 insertions(+)
> >  create mode 100644
> > Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt
> >
> > diff --git
> > a/Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt
> > b/Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt
> > new file mode 100644
> > index 0000000..f270b41
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt
> > @@ -0,0 +1,60 @@
> > +Properties for an MDIO bus mutiplexer found in Broadcom iProc based
SoCs.
> > +
> > +This MDIO bus multiplexer defines buses that could be internal as
> > +well as external to SoCs and could accept MDIO transaction compatible
> > +to C-22 or
> > +C-45 Clause. When Child bus is selected, one need to select these two
>
> s/Child/child/

Sure. Will ensure this.

> s/need/needs/

Sure. Will ensure this.

> > +properties as well to generate desired MDIO trascation on appropriate
bus.
> > +
> > +Required properties in addition to the generic multiplexer
properties:
> > +
> > +MDIO multiplexer node:
> > +- complatible: brcm,mdio-mux-iproc.
>
> typo
>
Fixed.
> > +
> > +Every non-ethernet PHY requires a compatible so that it could be
> > +probed based on this compatible string.
> > +
> > +Additional information regarding generic multiplexer properties could
> > +be found
>
> s/could/can/
>

Replaced.

> > +at- Documentation/devicetree/bindings/net/mdio-mux.txt
> > +
> > +
> > +for example:
> > +		mdio_mux_iproc: mdio_mux_iproc@6602023c {
>
> No '_' in node names.
>
> mdio-mux@...

Yes. Will take care of this.
>
> > +			compatible = "brcm,mdio-mux-iproc";
> > +			reg = <0x6602023c 0x14>;
> > +			#address-cells = <1>;
> > +			#size-cells = <0>;
> > +			mdio-integrated-mux;
> > +
> > +			mdio@0 {
> > +				reg = <0x0>;
> > +				#address-cells = <1>;
> > +				#size-cells = <0>;
> > +
> > +				pci_phy0: pci-phy@0 {
> > +					compatible = "brcm,ns2-pcie-phy";
> > +					reg = <0x0>;
> > +					#phy-cells = <0>;
> > +				};
> > +			};
> > +
> > +			mdio@7 {
> > +				reg = <0x7>;
> > +				#address-cells = <1>;
> > +				#size-cells = <0>;
> > +
> > +				pci_phy1: pci-phy@0 {
> > +					compatible = "brcm,ns2-pcie-phy";
> > +					reg = <0x0>;
> > +					#phy-cells = <0>;
> > +				};
> > +			};
> > +			mdio@10 {
> > +				reg = <0x10>;
> > +				#address-cells = <1>;
> > +				#size-cells = <0>;
> > +
> > +				gphy0: eth-phy@10 {
> > +					reg = <0x10>;
> > +				};
> > +			};
> > +		};
> > --
> > 1.9.1
> >

Regards,
Pramod

[PATCH v2 4/7] DT:mdio-mux: Add mdio multiplexer driver node

[Pramod Kumar]

Add integrated MDIO multiplexer driver node which contains
two mux PCIe bus and one ethernet bus along with phys
lying on these bus.

Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
---
 arch/arm64/boot/dts/broadcom/ns2-svk.dts | 12 ++++++++++++
 arch/arm64/boot/dts/broadcom/ns2.dtsi    | 32 ++++++++++++++++++++++++++++++++
 2 files changed, 44 insertions(+)

diff --git a/arch/arm64/boot/dts/broadcom/ns2-svk.dts b/arch/arm64/boot/dts/broadcom/ns2-svk.dts
index ce0ab84..8f6a6cc 100644
--- a/arch/arm64/boot/dts/broadcom/ns2-svk.dts
+++ b/arch/arm64/boot/dts/broadcom/ns2-svk.dts
@@ -87,3 +87,15 @@
 		#size-cells = <1>;
 	};
 };
+
+&mdio_mux_iproc {
+	mdio@10 {
+		reg = <0x10>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gphy0: eth-phy@10 {
+			reg = <0x10>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/broadcom/ns2.dtsi b/arch/arm64/boot/dts/broadcom/ns2.dtsi
index 6f81c9d..efc320a 100644
--- a/arch/arm64/boot/dts/broadcom/ns2.dtsi
+++ b/arch/arm64/boot/dts/broadcom/ns2.dtsi
@@ -330,6 +330,38 @@
 			      <0x65260000 0x1000>;
 		};
 
+		mdio_mux_iproc: mdio_mux_iproc@6602023c {
+			compatible = "brcm,mdio-mux-iproc";
+			reg = <0x6602023c 0x14>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			mdio-integrated-mux;
+
+			mdio@0 {
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				pci_phy0: pci-phy@0 {
+					compatible = "brcm,ns2-pcie-phy";
+					reg = <0x0>;
+					#phy-cells = <0>;
+				};
+			};
+
+			mdio@7 {
+				reg = <0x7>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				pci_phy1: pci-phy@0 {
+					compatible = "brcm,ns2-pcie-phy";
+					reg = <0x0>;
+					#phy-cells = <0>;
+				};
+			};
+		};
+
 		timer0: timer@66030000 {
 			compatible = "arm,sp804", "arm,primecell";
 			reg = <0x66030000 0x1000>;
-- 
1.9.1

[PATCH v2 5/7] net:mdio-mux: Add MDIO mux driver for iProc SoCs

[Pramod Kumar]

iProc based SoCs supports the integrated mdio multiplexer which
has the bus selection as well as mdio transaction generation logic
inside.

This mutiplexer has child buses for PCIe, SATA, USB and ETH. These
buses could be internal or external to SOC where PHYs are attached.
These buses could use C-45 or C-22 mdio transaction.

Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
---
 drivers/net/phy/Kconfig              |  11 ++
 drivers/net/phy/Makefile             |   1 +
 drivers/net/phy/mdio-mux-bcm-iproc.c | 243 +++++++++++++++++++++++++++++++++++
 3 files changed, 255 insertions(+)
 create mode 100644 drivers/net/phy/mdio-mux-bcm-iproc.c

diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 6dad9a9..38faecf 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -254,6 +254,17 @@ config MDIO_BUS_MUX_MMIOREG
 
 	  Currently, only 8-bit registers are supported.
 
+config MDIO_BUS_MUX_BCM_IPROC
+	tristate "Support for iProc based MDIO bus multiplexers"
+	depends on OF && OF_MDIO && (ARCH_BCM_IPROC || COMPILE_TEST)
+	select MDIO_BUS_MUX
+	default ARCH_BCM_IPROC
+	help
+	  This module provides a driver for MDIO bus multiplexers found in
+	  iProc based Broadcom SoCs. This mulitplexer connects one of several
+	  child MDIO bus to a parent bus. Buses could be interal as well as
+	  external and selection logic lies inside the same multiplexer.
+
 config MDIO_BCM_UNIMAC
 	tristate "Broadcom UniMAC MDIO bus controller"
 	depends on HAS_IOMEM
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index fcdbb92..f5951d5a 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -39,6 +39,7 @@ obj-$(CONFIG_AMD_PHY)		+= amd.o
 obj-$(CONFIG_MDIO_BUS_MUX)	+= mdio-mux.o
 obj-$(CONFIG_MDIO_BUS_MUX_GPIO)	+= mdio-mux-gpio.o
 obj-$(CONFIG_MDIO_BUS_MUX_MMIOREG) += mdio-mux-mmioreg.o
+obj-$(CONFIG_MDIO_BUS_MUX_BCM_IPROC)	+= mdio-mux-bcm-iproc.o
 obj-$(CONFIG_MDIO_SUN4I)	+= mdio-sun4i.o
 obj-$(CONFIG_MDIO_MOXART)	+= mdio-moxart.o
 obj-$(CONFIG_MDIO_BCM_UNIMAC)	+= mdio-bcm-unimac.o
diff --git a/drivers/net/phy/mdio-mux-bcm-iproc.c b/drivers/net/phy/mdio-mux-bcm-iproc.c
new file mode 100644
index 0000000..f047be6
--- /dev/null
+++ b/drivers/net/phy/mdio-mux-bcm-iproc.c
@@ -0,0 +1,243 @@
+/*
+ * Copyright 2016 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, version 2, as
+ * published by the Free Software Foundation (the "GPL").
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License version 2 (GPLv2) for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * version 2 (GPLv2) along with this source code.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/device.h>
+#include <linux/of_mdio.h>
+#include <linux/module.h>
+#include <linux/phy.h>
+#include <linux/mdio-mux.h>
+#include <linux/delay.h>
+
+#define MDIO_PARAM_OFFSET		0x00
+#define MDIO_PARAM_MIIM_CYCLE		29
+#define MDIO_PARAM_INTERNAL_SEL		25
+#define MDIO_PARAM_BUS_ID		22
+#define MDIO_PARAM_C45_SEL		21
+#define MDIO_PARAM_PHY_ID		16
+#define MDIO_PARAM_PHY_DATA		0
+
+#define MDIO_READ_OFFSET		0x04
+#define MDIO_READ_DATA_MASK		0xffff
+#define MDIO_ADDR_OFFSET		0x08
+
+#define MDIO_CTRL_OFFSET		0x0C
+#define MDIO_CTRL_WRITE_OP		0x1
+#define MDIO_CTRL_READ_OP		0x2
+
+#define MDIO_STAT_OFFSET		0x10
+#define MDIO_STAT_DONE			1
+
+#define BUS_MAX_ADDR			32
+#define EXT_BUS_START_ADDR		16
+
+struct iproc_mdiomux_desc {
+	void *mux_handle;
+	void __iomem *base;
+	struct device *dev;
+	struct mii_bus *mii_bus;
+};
+
+static int iproc_mdio_wait_for_idle(void __iomem *base, bool result)
+{
+	u32 val;
+	unsigned int timeout = 1000; /* loop for 1s */
+
+	do {
+		val = readl(base + MDIO_STAT_OFFSET);
+		if ((val & MDIO_STAT_DONE) == result)
+			return 0;
+
+		usleep_range(1000, 2000);
+	} while (timeout--);
+
+	return -ETIMEDOUT;
+}
+
+/* start_miim_ops- Program and start MDIO transaction over mdio bus.
+ * @base: Base address
+ * @phyid: phyid of the selected bus.
+ * @reg: register offset to be read/written.
+ * @val :0 if read op else value to be written in @reg;
+ * @op: Operation that need to be carried out.
+ *      MDIO_CTRL_READ_OP: Read transaction.
+ *      MDIO_CTRL_WRITE_OP: Write transaction.
+ *
+ * Return value: Successful Read operation returns read reg values and write
+ *      operation returns 0. Failure operation returns negative error code.
+ */
+static int start_miim_ops(void __iomem *base,
+			  u16 phyid, u32 reg, u16 val, u32 op)
+{
+	int ret;
+	u32 param;
+
+	writel(0, base + MDIO_CTRL_OFFSET);
+	ret = iproc_mdio_wait_for_idle(base, 0);
+	if (ret)
+		goto err;
+
+	param = readl(base + MDIO_PARAM_OFFSET);
+	param |= phyid << MDIO_PARAM_PHY_ID;
+	param |= val << MDIO_PARAM_PHY_DATA;
+	if (reg & MII_ADDR_C45)
+		param |= (1 << MDIO_PARAM_C45_SEL);
+
+	writel(param, base + MDIO_PARAM_OFFSET);
+
+	writel(reg, base + MDIO_ADDR_OFFSET);
+
+	writel(op, base + MDIO_CTRL_OFFSET);
+
+	ret = iproc_mdio_wait_for_idle(base, 1);
+	if (ret)
+		goto err;
+
+	if (op == MDIO_CTRL_READ_OP)
+		ret = readl(base + MDIO_READ_OFFSET) & MDIO_READ_DATA_MASK;
+err:
+	return ret;
+}
+
+static int iproc_mdiomux_read(struct mii_bus *bus, int phyid, int reg)
+{
+	int ret;
+	struct iproc_mdiomux_desc *md = bus->priv;
+
+	ret = start_miim_ops(md->base, phyid, reg, 0, MDIO_CTRL_READ_OP);
+	if (ret < 0)
+		dev_err(&bus->dev, "mdiomux read operation failed!!!");
+
+	return ret;
+}
+
+static int iproc_mdiomux_write(struct mii_bus *bus,
+			       int phyid, int reg, u16 val)
+{
+	int ret;
+	struct iproc_mdiomux_desc *md = bus->priv;
+
+	/* Write val at reg offset */
+	ret = start_miim_ops(md->base, phyid, reg, val, MDIO_CTRL_WRITE_OP);
+	if (ret < 0)
+		dev_err(&bus->dev, "mdiomux write operation failed!!!");
+
+	return ret;
+}
+
+static int mdio_mux_iproc_switch_fn(int current_child, int desired_child,
+				    void *data)
+{
+	struct iproc_mdiomux_desc *md = data;
+	u32 param, bus_id;
+	bool bus_dir;
+
+	/* select bus and its properties */
+	bus_dir = (desired_child < EXT_BUS_START_ADDR);
+	bus_id = bus_dir ? desired_child : (desired_child - EXT_BUS_START_ADDR);
+
+	param = (bus_dir ? 1 : 0) << MDIO_PARAM_INTERNAL_SEL;
+	param |= (bus_id << MDIO_PARAM_BUS_ID);
+
+	writel(param, md->base + MDIO_PARAM_OFFSET);
+	return 0;
+}
+
+static int mdio_mux_iproc_probe(struct platform_device *pdev)
+{
+	struct iproc_mdiomux_desc *md;
+	struct mii_bus *bus;
+	struct resource *res;
+	int rc;
+
+	md = devm_kzalloc(&pdev->dev, sizeof(*md), GFP_KERNEL);
+	if (!md)
+		return -ENOMEM;
+	md->dev = &pdev->dev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	md->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(md->base)) {
+		dev_err(&pdev->dev, "failed to ioremap register\n");
+		return PTR_ERR(md->base);
+	}
+
+	md->mii_bus = mdiobus_alloc();
+	if (!md->mii_bus) {
+		dev_err(&pdev->dev, "mdiomux bus alloc failed\n");
+		return -ENOMEM;
+	}
+
+	bus = md->mii_bus;
+	bus->priv = md;
+	bus->name = "iProc MDIO mux bus";
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s-%d", pdev->name, pdev->id);
+	bus->parent = &pdev->dev;
+	bus->read = iproc_mdiomux_read;
+	bus->write = iproc_mdiomux_write;
+
+	rc = of_mdiobus_register(bus, pdev->dev.of_node);
+	if (rc) {
+		dev_err(&pdev->dev, "mdiomux registration failed\n");
+		goto out;
+	}
+
+	platform_set_drvdata(pdev, md);
+
+	rc = mdio_mux_init(md->dev, mdio_mux_iproc_switch_fn,
+			   &md->mux_handle, md, md->mii_bus);
+	if (rc) {
+		dev_info(md->dev, "mdiomux initialization failed\n");
+		goto out;
+	}
+
+	dev_info(md->dev, "iProc mdiomux registered\n");
+	return 0;
+out:
+	mdiobus_free(bus);
+	return rc;
+}
+
+static int mdio_mux_iproc_remove(struct platform_device *pdev)
+{
+	struct iproc_mdiomux_desc *md = dev_get_platdata(&pdev->dev);
+
+	mdio_mux_uninit(md->mux_handle);
+	return 0;
+}
+
+static const struct of_device_id mdio_mux_iproc_match[] = {
+	{
+		.compatible = "brcm,mdio-mux-iproc",
+	},
+	{},
+};
+MODULE_DEVICE_TABLE(of, mdio_mux_iproc_match);
+
+static struct platform_driver mdiomux_iproc_driver = {
+	.driver = {
+		.name		= "mdio-mux-iproc",
+		.of_match_table = mdio_mux_iproc_match,
+	},
+	.probe		= mdio_mux_iproc_probe,
+	.remove		= mdio_mux_iproc_remove,
+};
+
+module_platform_driver(mdiomux_iproc_driver);
+
+MODULE_DESCRIPTION("iProc MDIO Mux Bus Driver");
+MODULE_AUTHOR("Pramod Kumar <pramod.kumar@broadcom.com>");
+MODULE_LICENSE("GPL v2");
-- 
1.9.1

Re: [PATCH v2 5/7] net:mdio-mux: Add MDIO mux driver for iProc SoCs

[David Miller]

From: Pramod Kumar <pramod.kumar@broadcom.com>
Date: Tue, 31 May 2016 19:06:39 +0530

> +static int iproc_mdio_wait_for_idle(void __iomem *base, bool result)
> +{
> +	u32 val;
> +	unsigned int timeout = 1000; /* loop for 1s */

Please order your local variable declarations from longest to shortest line.

> +static int start_miim_ops(void __iomem *base,
> +			  u16 phyid, u32 reg, u16 val, u32 op)
> +{
> +	int ret;
> +	u32 param;

Likewise.

> +static int iproc_mdiomux_read(struct mii_bus *bus, int phyid, int reg)
> +{
> +	int ret;
> +	struct iproc_mdiomux_desc *md = bus->priv;

Likewise.

RE: [PATCH v2 5/7] net:mdio-mux: Add MDIO mux driver for iProc SoCs

[Pramod Kumar]

Hi David,

> -----Original Message-----
> From: David Miller [mailto:davem@davemloft.net]
> Sent: 02 June 2016 04:48
> To: pramod.kumar@broadcom.com
> Cc: robh+dt@kernel.org; pawel.moll@arm.com; mark.rutland@arm.com;
> ijc+devicetree@hellion.org.uk; galak@codeaurora.org;
> catalin.marinas@arm.com; will.deacon@arm.com; kishon@ti.com;
> devicetree@vger.kernel.org; linux-arm-kernel@lists.infradead.org;
bcm-kernel-
> feedback-list@broadcom.com; linux-kernel@vger.kernel.org;
> netdev@vger.kernel.org
> Subject: Re: [PATCH v2 5/7] net:mdio-mux: Add MDIO mux driver for iProc
SoCs
>
> From: Pramod Kumar <pramod.kumar@broadcom.com>
> Date: Tue, 31 May 2016 19:06:39 +0530
>
> > +static int iproc_mdio_wait_for_idle(void __iomem *base, bool result)
> > +{
> > +	u32 val;
> > +	unsigned int timeout = 1000; /* loop for 1s */
>
> Please order your local variable declarations from longest to shortest
line.
>
> > +static int start_miim_ops(void __iomem *base,
> > +			  u16 phyid, u32 reg, u16 val, u32 op) {
> > +	int ret;
> > +	u32 param;
>
> Likewise.
>
Sure. I'll take care of this in next patch for all places.

> > +static int iproc_mdiomux_read(struct mii_bus *bus, int phyid, int
> > +reg) {
> > +	int ret;
> > +	struct iproc_mdiomux_desc *md = bus->priv;
>
> Likewise.
Sure. I'll take care of this in next patch for all places.

Regards,
Pramod

[PATCH v2 6/7] Binding:PHY: Binding doc for NS2 PCIe PHYs.

[Pramod Kumar]

Binding doc for NS2 PCIe PHYs.

Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
---
 .../bindings/phy/brcm,mdio-mux-bus-pci.txt         | 27 ++++++++++++++++++++++
 1 file changed, 27 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/brcm,mdio-mux-bus-pci.txt

diff --git a/Documentation/devicetree/bindings/phy/brcm,mdio-mux-bus-pci.txt b/Documentation/devicetree/bindings/phy/brcm,mdio-mux-bus-pci.txt
new file mode 100644
index 0000000..5b51007
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/brcm,mdio-mux-bus-pci.txt
@@ -0,0 +1,27 @@
+* Broadcom NS2 PCIe PHY binding document
+
+Required bus properties:
+- reg: MDIO Bus number for the MDIO interface
+- #address-cells: must be 1
+- #size-cells: must be 0
+
+Required PHY properties:
+- compatible: should be "brcm,ns2-pcie-phy"
+- reg: MDIO Phy ID for the MDIO interface
+- #phy-cells: must be 0
+
+This is a child bus node of "brcm,mdio-mux-iproc" node.
+
+Example:
+
+mdio@0 {
+	reg = <0x0>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	pci_phy0: pci-phy@0 {
+		compatible = "brcm,ns2-pcie-phy";
+		reg = <0x0>;
+		#phy-cells = <0>;
+	};
+};
-- 
1.9.1

Re: [PATCH v2 6/7] Binding:PHY: Binding doc for NS2 PCIe PHYs.

[Rob Herring]

On Tue, May 31, 2016 at 07:06:40PM +0530, Pramod Kumar wrote:
> Binding doc for NS2 PCIe PHYs.
> 
> Signed-off-by: Jon Mason <jonmason@broadcom.com>
> Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
> ---
>  .../bindings/phy/brcm,mdio-mux-bus-pci.txt         | 27 ++++++++++++++++++++++
>  1 file changed, 27 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/phy/brcm,mdio-mux-bus-pci.txt

Acked-by: Rob Herring <robh@kernel.org>

[PATCH v2 7/7] phy: Add Northstar2 PCI Phy support

[Pramod Kumar]

Add PCI Phy support for Broadcom Northstar2 SoCs.  This driver uses the
interface from the iproc mdio mux driver to enable the devices
respective phys.

Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
---
 drivers/phy/Kconfig            |   8 +++
 drivers/phy/Makefile           |   1 +
 drivers/phy/phy-bcm-ns2-pcie.c | 115 +++++++++++++++++++++++++++++++++++++++++
 3 files changed, 124 insertions(+)
 create mode 100644 drivers/phy/phy-bcm-ns2-pcie.c

diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index 26566db..5ff60b2 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -421,4 +421,12 @@ config PHY_CYGNUS_PCIE
 	  Enable this to support the Broadcom Cygnus PCIe PHY.
 	  If unsure, say N.
 
+config PHY_NS2_PCIE
+	tristate "Broadcom Northstar2 PCIe PHY driver"
+	depends on OF && MDIO_BUS_MUX_BCM_IPROC
+	select GENERIC_PHY
+	default ARCH_BCM_IPROC
+	help
+	  Enable this to support the Broadcom Northstar2 PCIe PHY.
+	  If unsure, say N.
 endmenu
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index 24596a9..77d51ff 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -52,3 +52,4 @@ obj-$(CONFIG_PHY_TUSB1210)		+= phy-tusb1210.o
 obj-$(CONFIG_PHY_BRCMSTB_SATA)		+= phy-brcmstb-sata.o
 obj-$(CONFIG_PHY_PISTACHIO_USB)		+= phy-pistachio-usb.o
 obj-$(CONFIG_PHY_CYGNUS_PCIE)		+= phy-bcm-cygnus-pcie.o
+obj-$(CONFIG_PHY_NS2_PCIE)		+= phy-bcm-ns2-pcie.o
diff --git a/drivers/phy/phy-bcm-ns2-pcie.c b/drivers/phy/phy-bcm-ns2-pcie.c
new file mode 100644
index 0000000..65c3870
--- /dev/null
+++ b/drivers/phy/phy-bcm-ns2-pcie.c
@@ -0,0 +1,115 @@
+/*
+ * Copyright (C) 2016 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/of_mdio.h>
+#include <linux/mdio.h>
+#include <linux/phy.h>
+#include <linux/phy/phy.h>
+
+struct ns2_pci_phy {
+	struct mdio_device *mdiodev;
+	struct phy *phy;
+};
+
+#define BLK_ADDR_REG_OFFSET	0x1f
+#define PLL_AFE1_100MHZ_BLK	0x2100
+#define PLL_CLK_AMP_OFFSET	0x03
+#define PLL_CLK_AMP_2P05V	0x2b18
+
+static int ns2_pci_phy_init(struct phy *p)
+{
+	struct ns2_pci_phy *phy = phy_get_drvdata(p);
+	int rc;
+
+	/* select the AFE 100MHz block page */
+	rc = mdiobus_write(phy->mdiodev->bus, phy->mdiodev->addr,
+			   BLK_ADDR_REG_OFFSET, PLL_AFE1_100MHZ_BLK);
+	if (rc)
+		goto err;
+
+	/* set the 100 MHz reference clock amplitude to 2.05 v */
+	rc = mdiobus_write(phy->mdiodev->bus, phy->mdiodev->addr,
+			   PLL_CLK_AMP_OFFSET, PLL_CLK_AMP_2P05V);
+	if (rc)
+		goto err;
+
+	return 0;
+
+err:
+	dev_err(&phy->mdiodev->dev, "Error %d writing to phy\n", rc);
+	return rc;
+}
+
+static struct phy_ops ns2_pci_phy_ops = {
+	.init = ns2_pci_phy_init,
+};
+
+static int ns2_pci_phy_probe(struct mdio_device *mdiodev)
+{
+	struct device *dev = &mdiodev->dev;
+	struct phy_provider *provider;
+	struct ns2_pci_phy *p;
+	struct phy *phy;
+
+	phy = devm_phy_create(dev, dev->of_node, &ns2_pci_phy_ops);
+	if (IS_ERR_OR_NULL(phy)) {
+		dev_err(dev, "failed to create Phy\n");
+		return PTR_ERR(phy);
+	}
+
+	p = devm_kmalloc(dev, sizeof(struct ns2_pci_phy),
+			 GFP_KERNEL);
+	if (!p)
+		return -ENOMEM;
+
+	p->mdiodev = mdiodev;
+	dev_set_drvdata(dev, p);
+
+	p->phy = phy;
+	phy_set_drvdata(phy, p);
+
+	provider = devm_of_phy_provider_register(&phy->dev,
+						 of_phy_simple_xlate);
+	if (IS_ERR(provider)) {
+		dev_err(dev, "failed to register Phy provider\n");
+		return PTR_ERR(provider);
+	}
+
+	dev_info(dev, "%s PHY registered\n", dev_name(dev));
+
+	return 0;
+}
+
+static const struct of_device_id ns2_pci_phy_of_match[] = {
+	{ .compatible = "brcm,ns2-pcie-phy", },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, ns2_pci_phy_of_match);
+
+static struct mdio_driver ns2_pci_phy_driver = {
+	.mdiodrv = {
+		.driver = {
+			.name = "phy-bcm-ns2-pci",
+			.of_match_table = ns2_pci_phy_of_match,
+		},
+	},
+	.probe = ns2_pci_phy_probe,
+};
+mdio_module_driver(ns2_pci_phy_driver);
+
+MODULE_AUTHOR("Broadcom");
+MODULE_DESCRIPTION("Broadcom Northstar2 PCI Phy driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:phy-bcm-ns2-pci");
-- 
1.9.1

Re: [PATCH v2 7/7] phy: Add Northstar2 PCI Phy support

[Andrew Lunn]

> +static int ns2_pci_phy_probe(struct mdio_device *mdiodev)
> +{
> +	struct device *dev = &mdiodev->dev;
> +	struct phy_provider *provider;
> +	struct ns2_pci_phy *p;
> +	struct phy *phy;
> +
> +	phy = devm_phy_create(dev, dev->of_node, &ns2_pci_phy_ops);
> +	if (IS_ERR_OR_NULL(phy)) {
> +		dev_err(dev, "failed to create Phy\n");
> +		return PTR_ERR(phy);
> +	}

https://www.mail-archive.com/linux-omap@vger.kernel.org/msg78030.html

	Andrew

RE: [PATCH v2 7/7] phy: Add Northstar2 PCI Phy support

[Pramod Kumar]

Hi Andrew,

> -----Original Message-----
> From: Andrew Lunn [mailto:andrew@lunn.ch]
> Sent: 01 June 2016 18:42
> To: Pramod Kumar
> Cc: Rob Herring; Pawel Moll; Mark Rutland; Ian Campbell; Kumar Gala;
Catalin
> Marinas; Will Deacon; Kishon Vijay Abraham I; David S. Miller;
> devicetree@vger.kernel.org; Jon Mason; netdev@vger.kernel.org; linux-
> kernel@vger.kernel.org; bcm-kernel-feedback-list@broadcom.com;
linux-arm-
> kernel@lists.infradead.org
> Subject: Re: [PATCH v2 7/7] phy: Add Northstar2 PCI Phy support
>
> > +static int ns2_pci_phy_probe(struct mdio_device *mdiodev) {
> > +	struct device *dev = &mdiodev->dev;
> > +	struct phy_provider *provider;
> > +	struct ns2_pci_phy *p;
> > +	struct phy *phy;
> > +
> > +	phy = devm_phy_create(dev, dev->of_node, &ns2_pci_phy_ops);
> > +	if (IS_ERR_OR_NULL(phy)) {
> > +		dev_err(dev, "failed to create Phy\n");
> > +		return PTR_ERR(phy);
> > +	}
>
> https://www.mail-archive.com/linux-omap@vger.kernel.org/msg78030.html
>

I've explored inside this API and see it never returning NULL. I'll
replace IS_ERR_OR_NULL to IS_ERR.
Thanks for pointing this out.

> 	Andrew

Regards,
Pramod