* [PATCH 0/2] ARM: dts: imx53: add support for USB armory board @ 2016-06-21 14:50 andrej 2016-06-21 14:50 ` [PATCH 1/2] devicetree: Add vendor prefix for Inverse Path andrej 2016-06-21 14:50 ` [PATCH 2/2] ARM: dts: imx53: add support for USB armory board andrej 0 siblings, 2 replies; 6+ messages in thread From: andrej @ 2016-06-21 14:50 UTC (permalink / raw) To: devicetree Cc: Shawn Guo, Sascha Hauer, Fabio Estevam, linux-arm-kernel, linux-kernel, Vagrant Cascadian From: Andrej Rosano <andrej@inversepath.com> This two patches add support for the USB armory board. The USB armory from Inverse Path is an open source hardware design, implementing a flash drive sized computer: https://inversepath.com/usbarmory Andrej Rosano (2): devicetree: Add vendor prefix for Inverse Path ARM: dts: imx53: add support for USB armory board .../devicetree/bindings/vendor-prefixes.txt | 1 + arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx53-usbarmory.dts | 239 +++++++++++++++++++++ 3 files changed, 241 insertions(+) create mode 100644 arch/arm/boot/dts/imx53-usbarmory.dts -- 2.9.0 ^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH 1/2] devicetree: Add vendor prefix for Inverse Path 2016-06-21 14:50 [PATCH 0/2] ARM: dts: imx53: add support for USB armory board andrej @ 2016-06-21 14:50 ` andrej 2016-06-21 21:59 ` Rob Herring 2016-06-21 14:50 ` [PATCH 2/2] ARM: dts: imx53: add support for USB armory board andrej 1 sibling, 1 reply; 6+ messages in thread From: andrej @ 2016-06-21 14:50 UTC (permalink / raw) To: devicetree Cc: Shawn Guo, Sascha Hauer, Fabio Estevam, linux-arm-kernel, linux-kernel, Vagrant Cascadian From: Andrej Rosano <andrej@inversepath.com> Inverse Path is an information security consulting company: https://inversepath.com Signed-off-by: Andrej Rosano <andrej@inversepath.com> --- Documentation/devicetree/bindings/vendor-prefixes.txt | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 2c2500d..37bfd91 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -134,6 +134,7 @@ innolux Innolux Corporation intel Intel Corporation intercontrol Inter Control Group invensense InvenSense Inc. +inversepath Inverse Path isee ISEE 2007 S.L. isil Intersil issi Integrated Silicon Solutions Inc. -- 2.9.0 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH 1/2] devicetree: Add vendor prefix for Inverse Path 2016-06-21 14:50 ` [PATCH 1/2] devicetree: Add vendor prefix for Inverse Path andrej @ 2016-06-21 21:59 ` Rob Herring 0 siblings, 0 replies; 6+ messages in thread From: Rob Herring @ 2016-06-21 21:59 UTC (permalink / raw) To: andrej Cc: devicetree, Vagrant Cascadian, linux-kernel, Sascha Hauer, Fabio Estevam, Shawn Guo, linux-arm-kernel On Tue, Jun 21, 2016 at 04:50:52PM +0200, andrej@inversepath.com wrote: > From: Andrej Rosano <andrej@inversepath.com> > > Inverse Path is an information security consulting company: > https://inversepath.com > > Signed-off-by: Andrej Rosano <andrej@inversepath.com> > --- > Documentation/devicetree/bindings/vendor-prefixes.txt | 1 + > 1 file changed, 1 insertion(+) Acked-by: Rob Herring <robh@kernel.org> ^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH 2/2] ARM: dts: imx53: add support for USB armory board 2016-06-21 14:50 [PATCH 0/2] ARM: dts: imx53: add support for USB armory board andrej 2016-06-21 14:50 ` [PATCH 1/2] devicetree: Add vendor prefix for Inverse Path andrej @ 2016-06-21 14:50 ` andrej 2016-06-28 1:50 ` Shawn Guo 1 sibling, 1 reply; 6+ messages in thread From: andrej @ 2016-06-21 14:50 UTC (permalink / raw) To: devicetree Cc: Shawn Guo, Sascha Hauer, Fabio Estevam, linux-arm-kernel, linux-kernel, Vagrant Cascadian From: Andrej Rosano <andrej@inversepath.com> Add support for Inverse Path USB armory board, an open source flash-drive sized computer based on NXP i.MX53 SoC. https://inversepath.com/usbarmory Signed-off-by: Andrej Rosano <andrej@inversepath.com> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx53-usbarmory.dts | 239 ++++++++++++++++++++++++++++++++++ 2 files changed, 240 insertions(+) create mode 100644 arch/arm/boot/dts/imx53-usbarmory.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 414b427..f8f85ab 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -303,6 +303,7 @@ dtb-$(CONFIG_SOC_IMX53) += \ imx53-smd.dtb \ imx53-tx53-x03x.dtb \ imx53-tx53-x13x.dtb \ + imx53-usbarmory.dtb \ imx53-voipac-bsb.dtb dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-apf6dev.dtb \ diff --git a/arch/arm/boot/dts/imx53-usbarmory.dts b/arch/arm/boot/dts/imx53-usbarmory.dts new file mode 100644 index 0000000..9a172fd --- /dev/null +++ b/arch/arm/boot/dts/imx53-usbarmory.dts @@ -0,0 +1,239 @@ +/* + * USB armory MkI device tree include file + * https://inversepath.com/usbarmory + * + * Copyright (C) 2015, Inverse Path + * Andrej Rosano <andrej@inversepath.com> + * + * Licensed under GPLv2 + */ + +/dts-v1/; +#include "imx53.dtsi" + +/ { + model = "Inverse Path USB armory"; + compatible = "inversepath,imx53-usbarmory", "fsl,imx53"; +}; + +/ { + chosen { + stdout-path = &uart1; + }; + + memory { + reg = <0x70000000 0x20000000>; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pin_gpio4_27>; + + user { + label = "LED"; + gpios = <&gpio4 27 0>; + linux,default-trigger = "heartbeat"; + }; + }; +}; + +&cpu0 { + operating-points = < + /* kHz */ + 166666 850000 + 400000 900000 + 800000 1050000 + >; +}; + +&esdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_esdhc1>; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + + imx53-usbarmory { + led_pin_gpio4_27: led_gpio4_27@0 { + fsl,pins = < + MX53_PAD_DISP0_DAT6__GPIO4_27 0x0 + >; + }; + + pinctrl_esdhc1: esdhc1grp { + fsl,pins = < + MX53_PAD_SD1_DATA0__ESDHC1_DAT0 0x1d5 + MX53_PAD_SD1_DATA1__ESDHC1_DAT1 0x1d5 + MX53_PAD_SD1_DATA2__ESDHC1_DAT2 0x1d5 + MX53_PAD_SD1_DATA3__ESDHC1_DAT3 0x1d5 + MX53_PAD_SD1_CMD__ESDHC1_CMD 0x1d5 + MX53_PAD_SD1_CLK__ESDHC1_CLK 0x1d5 + >; + }; + + pinctrl_i2c1_pmic: i2c1grp_pmic { + fsl,pins = < + MX53_PAD_EIM_D21__I2C1_SCL 0x0 + MX53_PAD_EIM_D28__I2C1_SDA 0x0 + >; + }; + + /* + * UART mode pin header configration + * 3 - GPIO5[26], pull-down 100K + * 4 - GPIO5[27], pull-down 100K + * 5 - TX, pull-up 100K + * 6 - RX, pull-up 100K + * 7 - GPIO5[30], pull-down 100K + */ + pinctrl_uart1: uart1grp { + fsl,pins = < + MX53_PAD_CSI0_DAT8__GPIO5_26 0xc0 + MX53_PAD_CSI0_DAT9__GPIO5_27 0xc0 + MX53_PAD_CSI0_DAT10__UART1_TXD_MUX 0x1e4 + MX53_PAD_CSI0_DAT11__UART1_RXD_MUX 0x1e4 + MX53_PAD_CSI0_DAT12__GPIO5_30 0xc0 + >; + }; + + /* + * GPIO mode pin header configuration + * 3 - GPIO5[26], pull-down 100K + * 4 - GPIO5[27], pull-down 100K + * 5 - GPIO5[28], pull-down 100K + * 6 - GPIO5[29], pull-down 100K + * 7 - GPIO5[30], pull-down 100K + */ + pinctrl_gpio5: gpio5grp { + fsl,pins = < + MX53_PAD_CSI0_DAT8__GPIO5_26 0xc0 + MX53_PAD_CSI0_DAT9__GPIO5_27 0xc0 + MX53_PAD_CSI0_DAT10__GPIO5_28 0xc0 + MX53_PAD_CSI0_DAT11__GPIO5_29 0xc0 + MX53_PAD_CSI0_DAT12__GPIO5_30 0xc0 + >; + }; + + /* + * SPI mode pin header configuration + * 3 - SCLK + * 4 - MOSI + * 5 - MISO + * 6 - /SS0 + * 7 - /SS1 + */ + pinctrl_ecspi2: ecspi2grp { + fsl,pins = < + MX53_PAD_CSI0_DAT8__ECSPI2_SCLK 0x0 + MX53_PAD_CSI0_DAT9__ECSPI2_MOSI 0x0 + MX53_PAD_CSI0_DAT10__ECSPI2_MISO 0x0 + MX53_PAD_CSI0_DAT11__GPIO5_29 0x0 + MX53_PAD_CSI0_DAT12__GPIO5_30 0x0 + >; + }; + + /* + * I2C mode pin header configuration + * 3 - SDA + * 4 - SCL + * 5 - GPIO5[28], pull-down 100K + * 6 - GPIO5[29], pull-down 100K + * 7 - GPIO5[30], pull-down 100K + */ + pinctrl_i2c1_pinheader: i2c1grp_pinheader { + fsl,pins = < + MX53_PAD_CSI0_DAT8__I2C1_SDA 0x0 + MX53_PAD_CSI0_DAT9__I2C1_SCL 0x0 + MX53_PAD_CSI0_DAT10__GPIO5_28 0xc0 + MX53_PAD_CSI0_DAT11__GPIO5_29 0xc0 + MX53_PAD_CSI0_DAT12__GPIO5_30 0xc0 + >; + }; + }; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&usbotg { + dr_mode = "peripheral"; + status = "okay"; +}; + +&i2c1 { + pinctrl-0 = <&pinctrl_i2c1_pmic>; + status = "okay"; + ltc3589: pmic@34 { + compatible = "lltc,ltc3589-2"; + reg = <0x34>; + regulators { + sw1_reg: sw1 { + regulator-min-microvolt = <591930>; + regulator-max-microvolt = <1224671>; + lltc,fb-voltage-divider = <100000 158000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <704123>; + regulator-max-microvolt = <1456803>; + lltc,fb-voltage-divider = <180000 191000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3_reg: sw3 { + regulator-min-microvolt = <1341250>; + regulator-max-microvolt = <2775000>; + lltc,fb-voltage-divider = <270000 100000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + bb_out_reg: bb-out { + regulator-min-microvolt = <3387341>; + regulator-max-microvolt = <3387341>; + lltc,fb-voltage-divider = <511000 158000>; + regulator-boot-on; + regulator-always-on; + }; + ldo1_reg: ldo1 { + regulator-min-microvolt = <1306329>; + regulator-max-microvolt = <1306329>; + lltc,fb-voltage-divider = <100000 158000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: ldo2 { + regulator-min-microvolt = <704123>; + regulator-max-microvolt = <1456806>; + lltc,fb-voltage-divider = <180000 191000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: ldo3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-boot-on; + }; + + ldo4_reg: ldo4 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3200000>; + }; + }; + }; +}; -- 2.9.0 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH 2/2] ARM: dts: imx53: add support for USB armory board 2016-06-21 14:50 ` [PATCH 2/2] ARM: dts: imx53: add support for USB armory board andrej @ 2016-06-28 1:50 ` Shawn Guo 2016-06-28 13:24 ` Andrej Rosano 0 siblings, 1 reply; 6+ messages in thread From: Shawn Guo @ 2016-06-28 1:50 UTC (permalink / raw) To: andrej Cc: devicetree, Vagrant Cascadian, linux-kernel, Sascha Hauer, Fabio Estevam, linux-arm-kernel On Tue, Jun 21, 2016 at 04:50:53PM +0200, andrej@inversepath.com wrote: > From: Andrej Rosano <andrej@inversepath.com> > > Add support for Inverse Path USB armory board, an open source > flash-drive sized computer based on NXP i.MX53 SoC. > > https://inversepath.com/usbarmory > > Signed-off-by: Andrej Rosano <andrej@inversepath.com> > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/imx53-usbarmory.dts | 239 ++++++++++++++++++++++++++++++++++ > 2 files changed, 240 insertions(+) > create mode 100644 arch/arm/boot/dts/imx53-usbarmory.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 414b427..f8f85ab 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -303,6 +303,7 @@ dtb-$(CONFIG_SOC_IMX53) += \ > imx53-smd.dtb \ > imx53-tx53-x03x.dtb \ > imx53-tx53-x13x.dtb \ > + imx53-usbarmory.dtb \ > imx53-voipac-bsb.dtb > dtb-$(CONFIG_SOC_IMX6Q) += \ > imx6dl-apf6dev.dtb \ > diff --git a/arch/arm/boot/dts/imx53-usbarmory.dts b/arch/arm/boot/dts/imx53-usbarmory.dts > new file mode 100644 > index 0000000..9a172fd > --- /dev/null > +++ b/arch/arm/boot/dts/imx53-usbarmory.dts > @@ -0,0 +1,239 @@ > +/* > + * USB armory MkI device tree include file > + * https://inversepath.com/usbarmory > + * > + * Copyright (C) 2015, Inverse Path > + * Andrej Rosano <andrej@inversepath.com> > + * > + * Licensed under GPLv2 > + */ Maybe GPL/X11 dual licence to consider non-Linux users. There are plenty of dual licence examples under arch/arm/boot/dts. > + > +/dts-v1/; > +#include "imx53.dtsi" > + > +/ { > + model = "Inverse Path USB armory"; > + compatible = "inversepath,imx53-usbarmory", "fsl,imx53"; > +}; > + > +/ { > + chosen { > + stdout-path = &uart1; > + }; > + > + memory { > + reg = <0x70000000 0x20000000>; > + }; > + > + leds { > + compatible = "gpio-leds"; > + pinctrl-names = "default"; > + pinctrl-0 = <&led_pin_gpio4_27>; > + > + user { > + label = "LED"; > + gpios = <&gpio4 27 0>; Use the macro in include/dt-bindings/gpio/gpio.h for polarity. > + linux,default-trigger = "heartbeat"; > + }; > + }; > +}; > + > +&cpu0 { > + operating-points = < > + /* kHz */ > + 166666 850000 > + 400000 900000 > + 800000 1050000 > + >; Can you put some comments in there explaining why you need a custom opp table for the board? > +}; > + > +&esdhc1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_esdhc1>; > + status = "okay"; > +}; > + > +&iomuxc { > + pinctrl-names = "default"; The property makes no sense where there is no pinctrl-0 property. > + > + imx53-usbarmory { This container node can be dropped to save an indentation level. > + led_pin_gpio4_27: led_gpio4_27@0 { Can this node be named in a similar scheme as other pinctrl entries? > + fsl,pins = < > + MX53_PAD_DISP0_DAT6__GPIO4_27 0x0 > + >; > + }; > + > + pinctrl_esdhc1: esdhc1grp { > + fsl,pins = < > + MX53_PAD_SD1_DATA0__ESDHC1_DAT0 0x1d5 > + MX53_PAD_SD1_DATA1__ESDHC1_DAT1 0x1d5 > + MX53_PAD_SD1_DATA2__ESDHC1_DAT2 0x1d5 > + MX53_PAD_SD1_DATA3__ESDHC1_DAT3 0x1d5 > + MX53_PAD_SD1_CMD__ESDHC1_CMD 0x1d5 > + MX53_PAD_SD1_CLK__ESDHC1_CLK 0x1d5 > + >; > + }; > + > + pinctrl_i2c1_pmic: i2c1grp_pmic { Please try to sort these pinctrl entries alphabetically. > + fsl,pins = < > + MX53_PAD_EIM_D21__I2C1_SCL 0x0 > + MX53_PAD_EIM_D28__I2C1_SDA 0x0 > + >; > + }; > + > + /* > + * UART mode pin header configration > + * 3 - GPIO5[26], pull-down 100K > + * 4 - GPIO5[27], pull-down 100K > + * 5 - TX, pull-up 100K > + * 6 - RX, pull-up 100K > + * 7 - GPIO5[30], pull-down 100K > + */ > + pinctrl_uart1: uart1grp { > + fsl,pins = < > + MX53_PAD_CSI0_DAT8__GPIO5_26 0xc0 > + MX53_PAD_CSI0_DAT9__GPIO5_27 0xc0 > + MX53_PAD_CSI0_DAT10__UART1_TXD_MUX 0x1e4 > + MX53_PAD_CSI0_DAT11__UART1_RXD_MUX 0x1e4 > + MX53_PAD_CSI0_DAT12__GPIO5_30 0xc0 > + >; > + }; > + > + /* > + * GPIO mode pin header configuration > + * 3 - GPIO5[26], pull-down 100K > + * 4 - GPIO5[27], pull-down 100K > + * 5 - GPIO5[28], pull-down 100K > + * 6 - GPIO5[29], pull-down 100K > + * 7 - GPIO5[30], pull-down 100K > + */ > + pinctrl_gpio5: gpio5grp { The entry is referenced nowhere. > + fsl,pins = < > + MX53_PAD_CSI0_DAT8__GPIO5_26 0xc0 > + MX53_PAD_CSI0_DAT9__GPIO5_27 0xc0 > + MX53_PAD_CSI0_DAT10__GPIO5_28 0xc0 > + MX53_PAD_CSI0_DAT11__GPIO5_29 0xc0 > + MX53_PAD_CSI0_DAT12__GPIO5_30 0xc0 > + >; > + }; > + > + /* > + * SPI mode pin header configuration > + * 3 - SCLK > + * 4 - MOSI > + * 5 - MISO > + * 6 - /SS0 > + * 7 - /SS1 > + */ > + pinctrl_ecspi2: ecspi2grp { > + fsl,pins = < > + MX53_PAD_CSI0_DAT8__ECSPI2_SCLK 0x0 > + MX53_PAD_CSI0_DAT9__ECSPI2_MOSI 0x0 > + MX53_PAD_CSI0_DAT10__ECSPI2_MISO 0x0 > + MX53_PAD_CSI0_DAT11__GPIO5_29 0x0 > + MX53_PAD_CSI0_DAT12__GPIO5_30 0x0 > + >; > + }; > + > + /* > + * I2C mode pin header configuration > + * 3 - SDA > + * 4 - SCL > + * 5 - GPIO5[28], pull-down 100K > + * 6 - GPIO5[29], pull-down 100K > + * 7 - GPIO5[30], pull-down 100K > + */ > + pinctrl_i2c1_pinheader: i2c1grp_pinheader { The entry is referenced nowhere. > + fsl,pins = < > + MX53_PAD_CSI0_DAT8__I2C1_SDA 0x0 > + MX53_PAD_CSI0_DAT9__I2C1_SCL 0x0 > + MX53_PAD_CSI0_DAT10__GPIO5_28 0xc0 > + MX53_PAD_CSI0_DAT11__GPIO5_29 0xc0 > + MX53_PAD_CSI0_DAT12__GPIO5_30 0xc0 > + >; > + }; > + }; > +}; > + > +&uart1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart1>; > + status = "okay"; > +}; > + > +&usbotg { > + dr_mode = "peripheral"; > + status = "okay"; > +}; > + > +&i2c1 { Please sort these nodes alphabetically in label name. > + pinctrl-0 = <&pinctrl_i2c1_pmic>; > + status = "okay"; Have a newline between property list and sub-node. > + ltc3589: pmic@34 { > + compatible = "lltc,ltc3589-2"; > + reg = <0x34>; Ditto Shawn > + regulators { > + sw1_reg: sw1 { > + regulator-min-microvolt = <591930>; > + regulator-max-microvolt = <1224671>; > + lltc,fb-voltage-divider = <100000 158000>; > + regulator-ramp-delay = <7000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + sw2_reg: sw2 { > + regulator-min-microvolt = <704123>; > + regulator-max-microvolt = <1456803>; > + lltc,fb-voltage-divider = <180000 191000>; > + regulator-ramp-delay = <7000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + sw3_reg: sw3 { > + regulator-min-microvolt = <1341250>; > + regulator-max-microvolt = <2775000>; > + lltc,fb-voltage-divider = <270000 100000>; > + regulator-ramp-delay = <7000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + bb_out_reg: bb-out { > + regulator-min-microvolt = <3387341>; > + regulator-max-microvolt = <3387341>; > + lltc,fb-voltage-divider = <511000 158000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + ldo1_reg: ldo1 { > + regulator-min-microvolt = <1306329>; > + regulator-max-microvolt = <1306329>; > + lltc,fb-voltage-divider = <100000 158000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + ldo2_reg: ldo2 { > + regulator-min-microvolt = <704123>; > + regulator-max-microvolt = <1456806>; > + lltc,fb-voltage-divider = <180000 191000>; > + regulator-ramp-delay = <7000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + ldo3_reg: ldo3 { > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + regulator-boot-on; > + }; > + > + ldo4_reg: ldo4 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <3200000>; > + }; > + }; > + }; > +}; > -- > 2.9.0 > > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 2/2] ARM: dts: imx53: add support for USB armory board 2016-06-28 1:50 ` Shawn Guo @ 2016-06-28 13:24 ` Andrej Rosano 0 siblings, 0 replies; 6+ messages in thread From: Andrej Rosano @ 2016-06-28 13:24 UTC (permalink / raw) To: Shawn Guo Cc: devicetree, Vagrant Cascadian, linux-kernel, Sascha Hauer, Fabio Estevam, linux-arm-kernel On 2016-06-28, Shawn Guo wrote: > Maybe GPL/X11 dual licence to consider non-Linux users. There are > plenty of dual licence examples under arch/arm/boot/dts. Applied this change along with the others you suggested in the patchset v2. Thanks, Andrej -- Andrej Rosano Inverse Path Srl <andrej@inversepath.com> http://www.inversepath.com 0x01939B21 5BB8 574E 68E8 D841 E18F D5E9 CEAD E0CF 0193 9B21 ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2016-06-28 13:35 UTC | newest] Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2016-06-21 14:50 [PATCH 0/2] ARM: dts: imx53: add support for USB armory board andrej 2016-06-21 14:50 ` [PATCH 1/2] devicetree: Add vendor prefix for Inverse Path andrej 2016-06-21 21:59 ` Rob Herring 2016-06-21 14:50 ` [PATCH 2/2] ARM: dts: imx53: add support for USB armory board andrej 2016-06-28 1:50 ` Shawn Guo 2016-06-28 13:24 ` Andrej Rosano
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).