From: Alexandre Belloni <alexandre.belloni@bootlin.com>
To: "David S . Miller" <davem@davemloft.net>
Cc: Allan Nielsen <Allan.Nielsen@microsemi.com>,
razvan.stefanescu@nxp.com, po.liu@nxp.com,
Thomas Petazzoni <thomas.petazzoni@bootlin.com>,
Andrew Lunn <andrew@lunn.ch>,
Florian Fainelli <f.fainelli@gmail.com>,
netdev@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-mips@linux-mips.org,
Alexandre Belloni <alexandre.belloni@bootlin.com>,
James Hogan <jhogan@kernel.org>
Subject: [PATCH net-next v3 5/7] MIPS: mscc: Add switch to ocelot
Date: Mon, 14 May 2018 22:04:58 +0200 [thread overview]
Message-ID: <20180514200500.2953-6-alexandre.belloni@bootlin.com> (raw)
In-Reply-To: <20180514200500.2953-1-alexandre.belloni@bootlin.com>
Ocelot has an integrated switch, add support for it.
Cc: James Hogan <jhogan@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
---
arch/mips/boot/dts/mscc/ocelot.dtsi | 88 +++++++++++++++++++++++++++++
1 file changed, 88 insertions(+)
diff --git a/arch/mips/boot/dts/mscc/ocelot.dtsi b/arch/mips/boot/dts/mscc/ocelot.dtsi
index dd239cab2f9d..4f33dbc67348 100644
--- a/arch/mips/boot/dts/mscc/ocelot.dtsi
+++ b/arch/mips/boot/dts/mscc/ocelot.dtsi
@@ -91,6 +91,72 @@
status = "disabled";
};
+ switch@1010000 {
+ compatible = "mscc,vsc7514-switch";
+ reg = <0x1010000 0x10000>,
+ <0x1030000 0x10000>,
+ <0x1080000 0x100>,
+ <0x10d0000 0x10000>,
+ <0x11e0000 0x100>,
+ <0x11f0000 0x100>,
+ <0x1200000 0x100>,
+ <0x1210000 0x100>,
+ <0x1220000 0x100>,
+ <0x1230000 0x100>,
+ <0x1240000 0x100>,
+ <0x1250000 0x100>,
+ <0x1260000 0x100>,
+ <0x1270000 0x100>,
+ <0x1280000 0x100>,
+ <0x1800000 0x80000>,
+ <0x1880000 0x10000>;
+ reg-names = "sys", "rew", "qs", "hsio", "port0",
+ "port1", "port2", "port3", "port4", "port5",
+ "port6", "port7", "port8", "port9", "port10",
+ "qsys", "ana";
+ interrupts = <21 22>;
+ interrupt-names = "xtr", "inj";
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port0: port@0 {
+ reg = <0>;
+ };
+ port1: port@1 {
+ reg = <1>;
+ };
+ port2: port@2 {
+ reg = <2>;
+ };
+ port3: port@3 {
+ reg = <3>;
+ };
+ port4: port@4 {
+ reg = <4>;
+ };
+ port5: port@5 {
+ reg = <5>;
+ };
+ port6: port@6 {
+ reg = <6>;
+ };
+ port7: port@7 {
+ reg = <7>;
+ };
+ port8: port@8 {
+ reg = <8>;
+ };
+ port9: port@9 {
+ reg = <9>;
+ };
+ port10: port@10 {
+ reg = <10>;
+ };
+ };
+ };
+
reset@1070008 {
compatible = "mscc,ocelot-chip-reset";
reg = <0x1070008 0x4>;
@@ -113,5 +179,27 @@
function = "uart2";
};
};
+
+ mdio0: mdio@107009c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "mscc,ocelot-miim";
+ reg = <0x107009c 0x36>, <0x10700f0 0x8>;
+ interrupts = <14>;
+ status = "disabled";
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+ phy2: ethernet-phy@2 {
+ reg = <2>;
+ };
+ phy3: ethernet-phy@3 {
+ reg = <3>;
+ };
+ };
};
};
--
2.17.0
next prev parent reply other threads:[~2018-05-14 20:07 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-05-14 20:04 [PATCH net-next v3 0/7] Microsemi Ocelot Ethernet switch support Alexandre Belloni
2018-05-14 20:04 ` [PATCH net-next v3 1/7] dt-bindings: net: add DT bindings for Microsemi MIIM Alexandre Belloni
2018-05-14 20:47 ` Andrew Lunn
2018-05-14 20:04 ` [PATCH net-next v3 2/7] net: phy: mscc-miim: Add MDIO driver Alexandre Belloni
2018-05-14 20:52 ` Florian Fainelli
2018-05-14 20:04 ` [PATCH net-next v3 3/7] dt-bindings: net: add DT bindings for Microsemi Ocelot Switch Alexandre Belloni
2018-05-14 20:49 ` Andrew Lunn
2018-05-14 20:53 ` Florian Fainelli
2018-05-14 20:04 ` [PATCH net-next v3 4/7] net: mscc: Add initial Ocelot switch support Alexandre Belloni
2018-05-14 20:56 ` Andrew Lunn
2018-05-14 20:04 ` Alexandre Belloni [this message]
2018-05-14 20:49 ` [PATCH net-next v3 5/7] MIPS: mscc: Add switch to ocelot Andrew Lunn
2018-05-14 20:54 ` Florian Fainelli
2018-05-14 20:04 ` [PATCH net-next v3 6/7] MIPS: mscc: connect phys to ports on ocelot_pcb123 Alexandre Belloni
2018-05-14 20:50 ` Andrew Lunn
2018-05-14 20:54 ` Florian Fainelli
2018-05-14 20:05 ` [PATCH net-next v3 7/7] MAINTAINERS: Add entry for Microsemi Ethernet switches Alexandre Belloni
2018-05-14 20:51 ` Andrew Lunn
2018-05-14 20:58 ` [PATCH net-next v3 0/7] Microsemi Ocelot Ethernet switch support Andrew Lunn
2018-05-14 21:47 ` James Hogan
2018-05-16 11:26 ` Alexandre Belloni
2018-05-15 20:45 ` David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180514200500.2953-6-alexandre.belloni@bootlin.com \
--to=alexandre.belloni@bootlin.com \
--cc=Allan.Nielsen@microsemi.com \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=f.fainelli@gmail.com \
--cc=jhogan@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mips@linux-mips.org \
--cc=netdev@vger.kernel.org \
--cc=po.liu@nxp.com \
--cc=razvan.stefanescu@nxp.com \
--cc=thomas.petazzoni@bootlin.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).