* [PATCH] arm64: dts: qcom: Add Dragonboard 845c
@ 2019-02-27 7:40 Bjorn Andersson
2019-02-27 14:25 ` Jeffrey Hugo
` (2 more replies)
0 siblings, 3 replies; 4+ messages in thread
From: Bjorn Andersson @ 2019-02-27 7:40 UTC (permalink / raw)
To: Andy Gross, David Brown, Rob Herring, Mark Rutland
Cc: linux-arm-msm, devicetree, linux-kernel
This adds an initial dts for the Dragonboard 845. Supported
functionality includes Debug UART, UFS, USB-C (peripheral), USB-A
(host), Ethernet, microSD-card and Bluetooth.
Initializing the SMMU is clearing the mapping used for the splash screen
framebuffer, which causes the baord to reboot. This can be worked around
using:
fastboot oem select-display-panel none
Ethernet and the second USB-A port depends on a functional firmware
loader for the uPD720201.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
This depends on the addition of the PCIe controller and PHY nodes, from
https://lore.kernel.org/lkml/20190227070022.31975-1-bjorn.andersson@linaro.org/
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/sdm845-db845c.dts | 570 +++++++++++++++++++++
2 files changed, 571 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sdm845-db845c.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 21d548f02d39..b3fe72ff2955 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8992-bullhead-rev-101.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8994-angler-rev-101.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8996-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8998-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
new file mode 100644
index 000000000000..0a5cfab6f6e2
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
@@ -0,0 +1,570 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sdm845.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
+
+/ {
+ model = "Thundercomm Dragonboard 845c";
+ compatible = "thundercomm,db845c", "qcom,sdm845";
+
+ aliases {
+ serial0 = &uart9;
+ hsuart0 = &uart6;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ dc12v: dc12v-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "DC12V";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ };
+
+ lt9611_1v8: lt9611-vdd18-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "LT9611_1V8";
+
+ vin-supply = <&vdc_5v>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ lt9611_3v3: lt9611-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "LT9611_3V3";
+
+ vin-supply = <&vdc_3v3>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ // TODO: make it possible to drive same GPIO from two clients
+ // gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>;
+ // enable-active-high;
+ };
+
+ pcie0_1p05v: pcie-0-1p05v-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "PCIE0_1.05V";
+
+ vin-supply = <&vbat>;
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+
+ // TODO: make it possible to drive same GPIO from two clients
+ // gpio = <&tlmm 90 GPIO_ACTIVE_HIGH>;
+ // enable-active-high;
+ };
+
+ pcie0_3p3v_dual: vldo-3v3-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "VLDO_3V3";
+
+ vin-supply = <&vbat>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 90 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&vol_up_pin_a>;
+
+ vol-up {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ user4 {
+ label = "db845c:green:user4";
+ gpios = <&pm8998_gpio 13 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+
+ wlan {
+ label = "db845c:yellow:wlan";
+ gpios = <&pm8998_gpio 9 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tx";
+ default-state = "off";
+ };
+
+ bt {
+ label = "db845c:blue:bt";
+ gpios = <&pm8998_gpio 5 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "bluetooth-power";
+ default-state = "off";
+ };
+ };
+
+ v5p0_hdmiout: v5p0-hdmiout-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "V5P0_HDMIOUT";
+
+ vin-supply = <&vdc_5v>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <500000>;
+
+ // TODO: make it possible to drive same GPIO from two clients
+ // gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>;
+ // enable-active-high;
+ };
+
+ vbat: vbat-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "VBAT";
+
+ vin-supply = <&dc12v>;
+ regulator-min-microvolt = <4200000>;
+ regulator-max-microvolt = <4200000>;
+ regulator-always-on;
+ };
+
+ vbat_som: vbat-som-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "VBAT_SOM";
+
+ vin-supply = <&dc12v>;
+ regulator-min-microvolt = <4200000>;
+ regulator-max-microvolt = <4200000>;
+ regulator-always-on;
+ };
+
+ vdc_3v3: vdc-3v3-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "VDC_3V3";
+ vin-supply = <&dc12v>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vdc_5v: vdc-5v-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "VDC_5V";
+
+ vin-supply = <&dc12v>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <500000>;
+ regulator-always-on;
+ };
+
+ vreg_s4a_1p8: vreg-s4a-1p8 {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_s4a_1p8";
+
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+
+ vin-supply = <&vbat_som>;
+ };
+};
+
+&apps_rsc {
+ pm8998-rpmh-regulators {
+ compatible = "qcom,pm8998-rpmh-regulators";
+ qcom,pmic-id = "a";
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-s6-supply = <&vph_pwr>;
+ vdd-s7-supply = <&vph_pwr>;
+ vdd-s8-supply = <&vph_pwr>;
+ vdd-s9-supply = <&vph_pwr>;
+ vdd-s10-supply = <&vph_pwr>;
+ vdd-s11-supply = <&vph_pwr>;
+ vdd-s12-supply = <&vph_pwr>;
+ vdd-s13-supply = <&vph_pwr>;
+ vdd-l1-l27-supply = <&vreg_s7a_1p025>;
+ vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
+ vdd-l3-l11-supply = <&vreg_s7a_1p025>;
+ vdd-l4-l5-supply = <&vreg_s7a_1p025>;
+ vdd-l6-supply = <&vph_pwr>;
+ vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
+ vdd-l9-supply = <&vreg_bob>;
+ vdd-l10-l23-l25-supply = <&vreg_bob>;
+ vdd-l13-l19-l21-supply = <&vreg_bob>;
+ vdd-l16-l28-supply = <&vreg_bob>;
+ vdd-l18-l22-supply = <&vreg_bob>;
+ vdd-l20-l24-supply = <&vreg_bob>;
+ vdd-l26-supply = <&vreg_s3a_1p35>;
+ vin-lvs-1-2-supply = <&vreg_s4a_1p8>;
+
+ vreg_s3a_1p35: smps3 {
+ regulator-min-microvolt = <1352000>;
+ regulator-max-microvolt = <1352000>;
+ };
+
+ vreg_s5a_2p04: smps5 {
+ regulator-min-microvolt = <1904000>;
+ regulator-max-microvolt = <2040000>;
+ };
+
+ vreg_s7a_1p025: smps7 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1028000>;
+ };
+
+ vreg_l1a_0p875: ldo1 {
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12a_1p8: ldo12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7a_1p8: ldo7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l13a_2p95: ldo13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l17a_1p3: ldo17 {
+ regulator-min-microvolt = <1304000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l20a_2p95: ldo20 {
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2968000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l21a_2p95: ldo21 {
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2968000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l24a_3p075: ldo24 {
+ regulator-min-microvolt = <3088000>;
+ regulator-max-microvolt = <3088000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l25a_3p3: ldo25 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l26a_1p2: ldo26 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ pmi8998-rpmh-regulators {
+ compatible = "qcom,pmi8998-rpmh-regulators";
+ qcom,pmic-id = "b";
+
+ vdd-bob-supply = <&vph_pwr>;
+
+ vreg_bob: bob {
+ regulator-min-microvolt = <3312000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+ regulator-allow-bypass;
+ };
+ };
+};
+
+&gcc {
+ protected-clocks = <GCC_QSPI_CORE_CLK>,
+ <GCC_QSPI_CORE_CLK_SRC>,
+ <GCC_QSPI_CNOC_PERIPH_AHB_CLK>;
+};
+
+&pcie0 {
+ status = "okay";
+ perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
+ enable-gpio = <&tlmm 134 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie0_perst_state>, <&pcie0_clkreq_state>, <&pcie0_wake_state>;
+
+ vddpe-3v3-supply = <&pcie0_3p3v_dual>;
+};
+
+&pcie0_phy {
+ status = "okay";
+
+ vdda-phy-supply = <&vreg_l1a_0p875>;
+ vdda-pll-supply = <&vreg_l26a_1p2>;
+};
+
+&pm8998_gpio {
+ vol_up_pin_a: vol-up-active {
+ pins = "gpio6";
+ function = "normal";
+ input-enable;
+ bias-pull-up;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ };
+};
+
+&pm8998_pon {
+ resin {
+ compatible = "qcom,pm8941-resin";
+ interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&sdhc_2 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdc2_clk &sdc2_cmd &sdc2_data &sd_card_det_n>;
+
+ vmmc-supply = <&vreg_l21a_2p95>;
+ vqmmc-supply = <&vreg_l13a_2p95>;
+
+ bus-width = <4>;
+ cd-gpios = <&tlmm 126 GPIO_ACTIVE_LOW>;
+};
+
+&tlmm {
+ pcie0_pwren_state: pcie0-pwren {
+ pins = "gpio90";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ pcie0_perst_state: pcie0-reset {
+ pins = "gpio35";
+ function = "gpio";
+
+ drive-strength = <2>;
+ output-low;
+ bias-pull-down;
+ };
+
+ pcie0_clkreq_state: pcie0-clkreq {
+ pins = "gpio36";
+ function = "pci_e0";
+ bias-pull-up;
+ };
+
+ pcie0_wake_state: pcie0-wake {
+ pins = "gpio37";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ sdc2_clk: sdc2-clk {
+ pins = "sdc2_clk";
+ bias-disable;
+
+ /*
+ * It seems that mmc_test reports errors if drive
+ * strength is not 16 on clk, cmd, and data pins.
+ */
+ drive-strength = <16>;
+ };
+
+ sdc2_cmd: sdc2-cmd {
+ pins = "sdc2_cmd";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ sdc2_data: sdc2-data {
+ pins = "sdc2_data";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ sd_card_det_n: sd-card-det-n {
+ pins = "gpio126";
+ function = "gpio";
+ bias-pull-up;
+ };
+};
+
+&uart6 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn3990-bt";
+
+ vddio-supply = <&vreg_s4a_1p8>;
+ vddxo-supply = <&vreg_l7a_1p8>;
+ vddrf-supply = <&vreg_l17a_1p3>;
+ vddch0-supply = <&vreg_l25a_3p3>;
+ max-speed = <3200000>;
+ };
+};
+
+&uart9 {
+ status = "okay";
+};
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3 {
+ dr_mode = "peripheral";
+};
+
+&usb_1_hsphy {
+ status = "okay";
+
+ vdd-supply = <&vreg_l1a_0p875>;
+ vdda-pll-supply = <&vreg_l12a_1p8>;
+ vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+
+ qcom,imp-res-offset-value = <8>;
+ qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
+ qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
+ qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
+};
+
+&usb_1_qmpphy {
+ status = "okay";
+
+ vdda-phy-supply = <&vreg_l26a_1p2>;
+ vdda-pll-supply = <&vreg_l1a_0p875>;
+};
+
+&usb_2 {
+ status = "okay";
+};
+
+&usb_2_dwc3 {
+ dr_mode = "host";
+};
+
+&usb_2_hsphy {
+ status = "okay";
+
+ vdd-supply = <&vreg_l1a_0p875>;
+ vdda-pll-supply = <&vreg_l12a_1p8>;
+ vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+
+ qcom,imp-res-offset-value = <8>;
+ qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_22_8_MA>;
+};
+
+&usb_2_qmpphy {
+ status = "okay";
+
+ vdda-phy-supply = <&vreg_l26a_1p2>;
+ vdda-pll-supply = <&vreg_l1a_0p875>;
+};
+
+&ufs_mem_hc {
+ status = "okay";
+
+ vcc-supply = <&vreg_l20a_2p95>;
+ vcc-max-microamp = <800000>;
+};
+
+&ufs_mem_phy {
+ status = "okay";
+
+ vdda-phy-supply = <&vreg_l1a_0p875>;
+ vdda-pll-supply = <&vreg_l26a_1p2>;
+};
+
+&wifi {
+ status = "okay";
+};
+
+/* PINCTRL - additions to nodes defined in sdm845.dtsi */
+
+&qup_uart6_default {
+ pinmux {
+ pins = "gpio45", "gpio46", "gpio47", "gpio48";
+ function = "qup6";
+ };
+
+ cts {
+ pins = "gpio45";
+ bias-disable;
+ };
+
+ rts-tx {
+ pins = "gpio46", "gpio47";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ rx {
+ pins = "gpio48";
+ bias-pull-up;
+ };
+};
+
+&qup_uart9_default {
+ pinconf-tx {
+ pins = "gpio4";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ pinconf-rx {
+ pins = "gpio5";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+};
--
2.18.0
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH] arm64: dts: qcom: Add Dragonboard 845c
2019-02-27 7:40 [PATCH] arm64: dts: qcom: Add Dragonboard 845c Bjorn Andersson
@ 2019-02-27 14:25 ` Jeffrey Hugo
2019-02-27 20:00 ` Nicolas Dechesne
2019-02-28 13:13 ` kbuild test robot
2 siblings, 0 replies; 4+ messages in thread
From: Jeffrey Hugo @ 2019-02-27 14:25 UTC (permalink / raw)
To: Bjorn Andersson, Andy Gross, David Brown, Rob Herring, Mark Rutland
Cc: linux-arm-msm, devicetree, linux-kernel
On 2/27/2019 12:40 AM, Bjorn Andersson wrote:
> This adds an initial dts for the Dragonboard 845. Supported
> functionality includes Debug UART, UFS, USB-C (peripheral), USB-A
> (host), Ethernet, microSD-card and Bluetooth.
>
> Initializing the SMMU is clearing the mapping used for the splash screen
> framebuffer, which causes the baord to reboot. This can be worked around
baord -> board?
> using:
>
> fastboot oem select-display-panel none
>
> Ethernet and the second USB-A port depends on a functional firmware
> loader for the uPD720201.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> ---
--
Jeffrey Hugo
Qualcomm Datacenter Technologies as an affiliate of Qualcomm
Technologies, Inc.
Qualcomm Technologies, Inc. is a member of the
Code Aurora Forum, a Linux Foundation Collaborative Project.
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH] arm64: dts: qcom: Add Dragonboard 845c
2019-02-27 7:40 [PATCH] arm64: dts: qcom: Add Dragonboard 845c Bjorn Andersson
2019-02-27 14:25 ` Jeffrey Hugo
@ 2019-02-27 20:00 ` Nicolas Dechesne
2019-02-28 13:13 ` kbuild test robot
2 siblings, 0 replies; 4+ messages in thread
From: Nicolas Dechesne @ 2019-02-27 20:00 UTC (permalink / raw)
To: Bjorn Andersson
Cc: Andy Gross, David Brown, Rob Herring, Mark Rutland,
linux-arm-msm, devicetree, lkml
On Wed, Feb 27, 2019 at 8:39 AM Bjorn Andersson
<bjorn.andersson@linaro.org> wrote:
>
> This adds an initial dts for the Dragonboard 845. Supported
> functionality includes Debug UART, UFS, USB-C (peripheral), USB-A
> (host), Ethernet, microSD-card and Bluetooth.
>
> Initializing the SMMU is clearing the mapping used for the splash screen
> framebuffer, which causes the baord to reboot. This can be worked around
> using:
>
> fastboot oem select-display-panel none
>
> Ethernet and the second USB-A port depends on a functional firmware
> loader for the uPD720201.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> ---
>
> This depends on the addition of the PCIe controller and PHY nodes, from
> https://lore.kernel.org/lkml/20190227070022.31975-1-bjorn.andersson@linaro.org/
>
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> arch/arm64/boot/dts/qcom/sdm845-db845c.dts | 570 +++++++++++++++++++++
> 2 files changed, 571 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/sdm845-db845c.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 21d548f02d39..b3fe72ff2955 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8992-bullhead-rev-101.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8994-angler-rev-101.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8996-mtp.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8998-mtp.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
> new file mode 100644
> index 000000000000..0a5cfab6f6e2
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
> @@ -0,0 +1,570 @@
> +// SPDX-License-Identifier: GPL-2.0
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> +#include "sdm845.dtsi"
> +#include "pm8998.dtsi"
> +#include "pmi8998.dtsi"
> +
> +/ {
> + model = "Thundercomm Dragonboard 845c";
> + compatible = "thundercomm,db845c", "qcom,sdm845";
> +
> + aliases {
> + serial0 = &uart9;
> + hsuart0 = &uart6;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + dc12v: dc12v-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "DC12V";
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + regulator-always-on;
> + };
> +
> + lt9611_1v8: lt9611-vdd18-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "LT9611_1V8";
> +
> + vin-supply = <&vdc_5v>;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> +
> + gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + lt9611_3v3: lt9611-3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "LT9611_3V3";
> +
> + vin-supply = <&vdc_3v3>;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +
> + // TODO: make it possible to drive same GPIO from two clients
> + // gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>;
> + // enable-active-high;
> + };
> +
> + pcie0_1p05v: pcie-0-1p05v-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "PCIE0_1.05V";
> +
> + vin-supply = <&vbat>;
> + regulator-min-microvolt = <1050000>;
> + regulator-max-microvolt = <1050000>;
> +
> + // TODO: make it possible to drive same GPIO from two clients
> + // gpio = <&tlmm 90 GPIO_ACTIVE_HIGH>;
> + // enable-active-high;
> + };
> +
> + pcie0_3p3v_dual: vldo-3v3-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "VLDO_3V3";
> +
> + vin-supply = <&vbat>;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +
> + gpio = <&tlmm 90 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + gpio_keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + autorepeat;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&vol_up_pin_a>;
> +
> + vol-up {
> + label = "Volume Up";
> + linux,code = <KEY_VOLUMEUP>;
> + gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + user4 {
> + label = "db845c:green:user4";
I think we've agreed to standardize on label names for 96boards
compatible boards.
https://lore.kernel.org/lkml/20190205192412.GG31919@minitux/
> + gpios = <&pm8998_gpio 13 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + default-state = "off";
> + };
> +
> + wlan {
> + label = "db845c:yellow:wlan";
> + gpios = <&pm8998_gpio 9 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "phy0tx";
> + default-state = "off";
> + };
> +
> + bt {
> + label = "db845c:blue:bt";
> + gpios = <&pm8998_gpio 5 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "bluetooth-power";
> + default-state = "off";
> + };
> + };
> +
> + v5p0_hdmiout: v5p0-hdmiout-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "V5P0_HDMIOUT";
> +
> + vin-supply = <&vdc_5v>;
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <500000>;
> +
> + // TODO: make it possible to drive same GPIO from two clients
> + // gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>;
> + // enable-active-high;
> + };
> +
> + vbat: vbat-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "VBAT";
> +
> + vin-supply = <&dc12v>;
> + regulator-min-microvolt = <4200000>;
> + regulator-max-microvolt = <4200000>;
> + regulator-always-on;
> + };
> +
> + vbat_som: vbat-som-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "VBAT_SOM";
> +
> + vin-supply = <&dc12v>;
> + regulator-min-microvolt = <4200000>;
> + regulator-max-microvolt = <4200000>;
> + regulator-always-on;
> + };
> +
> + vdc_3v3: vdc-3v3-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "VDC_3V3";
> + vin-supply = <&dc12v>;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vdc_5v: vdc-5v-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "VDC_5V";
> +
> + vin-supply = <&dc12v>;
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <500000>;
> + regulator-always-on;
> + };
> +
> + vreg_s4a_1p8: vreg-s4a-1p8 {
> + compatible = "regulator-fixed";
> + regulator-name = "vreg_s4a_1p8";
> +
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + vph_pwr: vph-pwr-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vph_pwr";
> +
> + vin-supply = <&vbat_som>;
> + };
> +};
> +
> +&apps_rsc {
> + pm8998-rpmh-regulators {
> + compatible = "qcom,pm8998-rpmh-regulators";
> + qcom,pmic-id = "a";
> + vdd-s1-supply = <&vph_pwr>;
> + vdd-s2-supply = <&vph_pwr>;
> + vdd-s3-supply = <&vph_pwr>;
> + vdd-s4-supply = <&vph_pwr>;
> + vdd-s5-supply = <&vph_pwr>;
> + vdd-s6-supply = <&vph_pwr>;
> + vdd-s7-supply = <&vph_pwr>;
> + vdd-s8-supply = <&vph_pwr>;
> + vdd-s9-supply = <&vph_pwr>;
> + vdd-s10-supply = <&vph_pwr>;
> + vdd-s11-supply = <&vph_pwr>;
> + vdd-s12-supply = <&vph_pwr>;
> + vdd-s13-supply = <&vph_pwr>;
> + vdd-l1-l27-supply = <&vreg_s7a_1p025>;
> + vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
> + vdd-l3-l11-supply = <&vreg_s7a_1p025>;
> + vdd-l4-l5-supply = <&vreg_s7a_1p025>;
> + vdd-l6-supply = <&vph_pwr>;
> + vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
> + vdd-l9-supply = <&vreg_bob>;
> + vdd-l10-l23-l25-supply = <&vreg_bob>;
> + vdd-l13-l19-l21-supply = <&vreg_bob>;
> + vdd-l16-l28-supply = <&vreg_bob>;
> + vdd-l18-l22-supply = <&vreg_bob>;
> + vdd-l20-l24-supply = <&vreg_bob>;
> + vdd-l26-supply = <&vreg_s3a_1p35>;
> + vin-lvs-1-2-supply = <&vreg_s4a_1p8>;
> +
> + vreg_s3a_1p35: smps3 {
> + regulator-min-microvolt = <1352000>;
> + regulator-max-microvolt = <1352000>;
> + };
> +
> + vreg_s5a_2p04: smps5 {
> + regulator-min-microvolt = <1904000>;
> + regulator-max-microvolt = <2040000>;
> + };
> +
> + vreg_s7a_1p025: smps7 {
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <1028000>;
> + };
> +
> + vreg_l1a_0p875: ldo1 {
> + regulator-min-microvolt = <880000>;
> + regulator-max-microvolt = <880000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l12a_1p8: ldo12 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l7a_1p8: ldo7 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l13a_2p95: ldo13 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <2960000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l17a_1p3: ldo17 {
> + regulator-min-microvolt = <1304000>;
> + regulator-max-microvolt = <1304000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l20a_2p95: ldo20 {
> + regulator-min-microvolt = <2960000>;
> + regulator-max-microvolt = <2968000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l21a_2p95: ldo21 {
> + regulator-min-microvolt = <2960000>;
> + regulator-max-microvolt = <2968000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l24a_3p075: ldo24 {
> + regulator-min-microvolt = <3088000>;
> + regulator-max-microvolt = <3088000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l25a_3p3: ldo25 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3312000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l26a_1p2: ldo26 {
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +
> + pmi8998-rpmh-regulators {
> + compatible = "qcom,pmi8998-rpmh-regulators";
> + qcom,pmic-id = "b";
> +
> + vdd-bob-supply = <&vph_pwr>;
> +
> + vreg_bob: bob {
> + regulator-min-microvolt = <3312000>;
> + regulator-max-microvolt = <3600000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
> + regulator-allow-bypass;
> + };
> + };
> +};
> +
> +&gcc {
> + protected-clocks = <GCC_QSPI_CORE_CLK>,
> + <GCC_QSPI_CORE_CLK_SRC>,
> + <GCC_QSPI_CNOC_PERIPH_AHB_CLK>;
> +};
> +
> +&pcie0 {
> + status = "okay";
> + perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
> + enable-gpio = <&tlmm 134 GPIO_ACTIVE_HIGH>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie0_perst_state>, <&pcie0_clkreq_state>, <&pcie0_wake_state>;
> +
> + vddpe-3v3-supply = <&pcie0_3p3v_dual>;
> +};
> +
> +&pcie0_phy {
> + status = "okay";
> +
> + vdda-phy-supply = <&vreg_l1a_0p875>;
> + vdda-pll-supply = <&vreg_l26a_1p2>;
> +};
> +
> +&pm8998_gpio {
> + vol_up_pin_a: vol-up-active {
> + pins = "gpio6";
> + function = "normal";
> + input-enable;
> + bias-pull-up;
> + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
> + };
> +};
> +
> +&pm8998_pon {
> + resin {
> + compatible = "qcom,pm8941-resin";
> + interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
> + debounce = <15625>;
> + bias-pull-up;
> + linux,code = <KEY_VOLUMEDOWN>;
> + };
> +};
> +
> +&qupv3_id_0 {
> + status = "okay";
> +};
> +
> +&qupv3_id_1 {
> + status = "okay";
> +};
> +
> +&sdhc_2 {
> + status = "okay";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdc2_clk &sdc2_cmd &sdc2_data &sd_card_det_n>;
> +
> + vmmc-supply = <&vreg_l21a_2p95>;
> + vqmmc-supply = <&vreg_l13a_2p95>;
> +
> + bus-width = <4>;
> + cd-gpios = <&tlmm 126 GPIO_ACTIVE_LOW>;
> +};
> +
> +&tlmm {
> + pcie0_pwren_state: pcie0-pwren {
> + pins = "gpio90";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + pcie0_perst_state: pcie0-reset {
> + pins = "gpio35";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + output-low;
> + bias-pull-down;
> + };
> +
> + pcie0_clkreq_state: pcie0-clkreq {
> + pins = "gpio36";
> + function = "pci_e0";
> + bias-pull-up;
> + };
> +
> + pcie0_wake_state: pcie0-wake {
> + pins = "gpio37";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + sdc2_clk: sdc2-clk {
> + pins = "sdc2_clk";
> + bias-disable;
> +
> + /*
> + * It seems that mmc_test reports errors if drive
> + * strength is not 16 on clk, cmd, and data pins.
> + */
> + drive-strength = <16>;
> + };
> +
> + sdc2_cmd: sdc2-cmd {
> + pins = "sdc2_cmd";
> + bias-pull-up;
> + drive-strength = <10>;
> + };
> +
> + sdc2_data: sdc2-data {
> + pins = "sdc2_data";
> + bias-pull-up;
> + drive-strength = <10>;
> + };
> +
> + sd_card_det_n: sd-card-det-n {
> + pins = "gpio126";
> + function = "gpio";
> + bias-pull-up;
> + };
> +};
> +
> +&uart6 {
> + status = "okay";
> +
> + bluetooth {
> + compatible = "qcom,wcn3990-bt";
> +
> + vddio-supply = <&vreg_s4a_1p8>;
> + vddxo-supply = <&vreg_l7a_1p8>;
> + vddrf-supply = <&vreg_l17a_1p3>;
> + vddch0-supply = <&vreg_l25a_3p3>;
> + max-speed = <3200000>;
> + };
> +};
> +
> +&uart9 {
> + status = "okay";
> +};
> +
> +&usb_1 {
> + status = "okay";
> +};
> +
> +&usb_1_dwc3 {
> + dr_mode = "peripheral";
> +};
> +
> +&usb_1_hsphy {
> + status = "okay";
> +
> + vdd-supply = <&vreg_l1a_0p875>;
> + vdda-pll-supply = <&vreg_l12a_1p8>;
> + vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
> +
> + qcom,imp-res-offset-value = <8>;
> + qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
> + qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
> + qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
> +};
> +
> +&usb_1_qmpphy {
> + status = "okay";
> +
> + vdda-phy-supply = <&vreg_l26a_1p2>;
> + vdda-pll-supply = <&vreg_l1a_0p875>;
> +};
> +
> +&usb_2 {
> + status = "okay";
> +};
> +
> +&usb_2_dwc3 {
> + dr_mode = "host";
> +};
> +
> +&usb_2_hsphy {
> + status = "okay";
> +
> + vdd-supply = <&vreg_l1a_0p875>;
> + vdda-pll-supply = <&vreg_l12a_1p8>;
> + vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
> +
> + qcom,imp-res-offset-value = <8>;
> + qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_22_8_MA>;
> +};
> +
> +&usb_2_qmpphy {
> + status = "okay";
> +
> + vdda-phy-supply = <&vreg_l26a_1p2>;
> + vdda-pll-supply = <&vreg_l1a_0p875>;
> +};
> +
> +&ufs_mem_hc {
> + status = "okay";
> +
> + vcc-supply = <&vreg_l20a_2p95>;
> + vcc-max-microamp = <800000>;
> +};
> +
> +&ufs_mem_phy {
> + status = "okay";
> +
> + vdda-phy-supply = <&vreg_l1a_0p875>;
> + vdda-pll-supply = <&vreg_l26a_1p2>;
> +};
> +
> +&wifi {
> + status = "okay";
> +};
> +
> +/* PINCTRL - additions to nodes defined in sdm845.dtsi */
> +
> +&qup_uart6_default {
> + pinmux {
> + pins = "gpio45", "gpio46", "gpio47", "gpio48";
> + function = "qup6";
> + };
> +
> + cts {
> + pins = "gpio45";
> + bias-disable;
> + };
> +
> + rts-tx {
> + pins = "gpio46", "gpio47";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + rx {
> + pins = "gpio48";
> + bias-pull-up;
> + };
> +};
> +
> +&qup_uart9_default {
> + pinconf-tx {
> + pins = "gpio4";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + pinconf-rx {
> + pins = "gpio5";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +};
> --
> 2.18.0
>
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH] arm64: dts: qcom: Add Dragonboard 845c
2019-02-27 7:40 [PATCH] arm64: dts: qcom: Add Dragonboard 845c Bjorn Andersson
2019-02-27 14:25 ` Jeffrey Hugo
2019-02-27 20:00 ` Nicolas Dechesne
@ 2019-02-28 13:13 ` kbuild test robot
2 siblings, 0 replies; 4+ messages in thread
From: kbuild test robot @ 2019-02-28 13:13 UTC (permalink / raw)
To: Bjorn Andersson
Cc: kbuild-all, Andy Gross, David Brown, Rob Herring, Mark Rutland,
linux-arm-msm, devicetree, linux-kernel
[-- Attachment #1: Type: text/plain, Size: 1246 bytes --]
Hi Bjorn,
I love your patch! Yet something to improve:
[auto build test ERROR on agross/for-next]
[also build test ERROR on v5.0-rc8 next-20190228]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]
url: https://github.com/0day-ci/linux/commits/Bjorn-Andersson/arm64-dts-qcom-Add-Dragonboard-845c/20190228-041139
base: https://git.kernel.org/pub/scm/linux/kernel/git/agross/linux.git for-next
config: arm64-allyesconfig (attached as .config)
compiler: aarch64-linux-gnu-gcc (Debian 8.2.0-11) 8.2.0
reproduce:
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# save the attached .config to linux build tree
GCC_VERSION=8.2.0 make.cross ARCH=arm64
All errors (new ones prefixed by >>):
>> Error: arch/arm64/boot/dts/qcom/sdm845-db845c.dts:322.1-7 Label or path pcie0 not found
>> Error: arch/arm64/boot/dts/qcom/sdm845-db845c.dts:333.1-11 Label or path pcie0_phy not found
>> FATAL ERROR: Syntax error parsing input tree
---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation
[-- Attachment #2: .config.gz --]
[-- Type: application/gzip, Size: 63040 bytes --]
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2019-02-28 13:14 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-02-27 7:40 [PATCH] arm64: dts: qcom: Add Dragonboard 845c Bjorn Andersson
2019-02-27 14:25 ` Jeffrey Hugo
2019-02-27 20:00 ` Nicolas Dechesne
2019-02-28 13:13 ` kbuild test robot
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).