[PATCH AUTOSEL 4.4 01/68] scsi: lpfc: Fix dif and first burst use in write commands

[PATCH AUTOSEL 4.4 01/68] scsi: lpfc: Fix dif and first burst use in write commands

[Sasha Levin]

From: James Smart <jsmart2021@gmail.com>

[ Upstream commit 7c4042a4d0b7532cfbc90478fd3084b2dab5849e ]

When dif and first burst is used in a write command wqe, the driver was not
properly setting fields in the io command request. This resulted in no dif
bytes being sent and invalid xfer_rdy's, resulting in the io being aborted
by the hardware.

Correct the wqe initializaton when both dif and first burst are used.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/lpfc/lpfc_scsi.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/drivers/scsi/lpfc/lpfc_scsi.c b/drivers/scsi/lpfc/lpfc_scsi.c
index bae36cc3740b6..ab6bff60478f9 100644
--- a/drivers/scsi/lpfc/lpfc_scsi.c
+++ b/drivers/scsi/lpfc/lpfc_scsi.c
@@ -2707,6 +2707,7 @@ lpfc_bg_scsi_prep_dma_buf_s3(struct lpfc_hba *phba,
 	int datasegcnt, protsegcnt, datadir = scsi_cmnd->sc_data_direction;
 	int prot_group_type = 0;
 	int fcpdl;
+	struct lpfc_vport *vport = phba->pport;
 
 	/*
 	 * Start the lpfc command prep by bumping the bpl beyond fcp_cmnd
@@ -2812,6 +2813,14 @@ lpfc_bg_scsi_prep_dma_buf_s3(struct lpfc_hba *phba,
 	 */
 	iocb_cmd->un.fcpi.fcpi_parm = fcpdl;
 
+	/*
+	 * For First burst, we may need to adjust the initial transfer
+	 * length for DIF
+	 */
+	if (iocb_cmd->un.fcpi.fcpi_XRdy &&
+	    (fcpdl < vport->cfg_first_burst_size))
+		iocb_cmd->un.fcpi.fcpi_XRdy = fcpdl;
+
 	return 0;
 err:
 	if (lpfc_cmd->seg_cnt)
@@ -3361,6 +3370,7 @@ lpfc_bg_scsi_prep_dma_buf_s4(struct lpfc_hba *phba,
 	int datasegcnt, protsegcnt, datadir = scsi_cmnd->sc_data_direction;
 	int prot_group_type = 0;
 	int fcpdl;
+	struct lpfc_vport *vport = phba->pport;
 
 	/*
 	 * Start the lpfc command prep by bumping the sgl beyond fcp_cmnd
@@ -3476,6 +3486,14 @@ lpfc_bg_scsi_prep_dma_buf_s4(struct lpfc_hba *phba,
 	 */
 	iocb_cmd->un.fcpi.fcpi_parm = fcpdl;
 
+	/*
+	 * For First burst, we may need to adjust the initial transfer
+	 * length for DIF
+	 */
+	if (iocb_cmd->un.fcpi.fcpi_XRdy &&
+	    (fcpdl < vport->cfg_first_burst_size))
+		iocb_cmd->un.fcpi.fcpi_XRdy = fcpdl;
+
 	/*
 	 * If the OAS driver feature is enabled and the lun is enabled for
 	 * OAS, set the oas iocb related flags.
-- 
2.20.1

[PATCH AUTOSEL 4.4 03/68] ARM: dts: imx53-voipac-dmm-668: Fix memory node duplication

[Sasha Levin]

From: Fabio Estevam <festevam@gmail.com>

[ Upstream commit 998a84c27a7f3f9133d32af64e19c05cec161a1a ]

imx53-voipac-dmm-668 has two memory nodes, but the correct representation
would be to use a single one with two reg entries - one for each RAM chip
select, so fix it accordingly.

Reported-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx53-voipac-dmm-668.dtsi | 8 ++------
 1 file changed, 2 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/imx53-voipac-dmm-668.dtsi b/arch/arm/boot/dts/imx53-voipac-dmm-668.dtsi
index ba689fbd0e413..301cf8d45947f 100644
--- a/arch/arm/boot/dts/imx53-voipac-dmm-668.dtsi
+++ b/arch/arm/boot/dts/imx53-voipac-dmm-668.dtsi
@@ -17,12 +17,8 @@
 
 	memory@70000000 {
 		device_type = "memory";
-		reg = <0x70000000 0x20000000>;
-	};
-
-	memory@b0000000 {
-		device_type = "memory";
-		reg = <0xb0000000 0x20000000>;
+		reg = <0x70000000 0x20000000>,
+		      <0xb0000000 0x20000000>;
 	};
 
 	regulators {
-- 
2.20.1

[PATCH AUTOSEL 4.4 04/68] parisc: Fix serio address output

[Sasha Levin]

From: Helge Deller <deller@gmx.de>

[ Upstream commit 785145171d17af2554128becd6a7c8f89e101141 ]

We want the hpa addresses printed in the serio modules, not some
virtual ioremap()ed address, e.g.:

 serio: gsc-ps2-keyboard port at 0xf0108000 irq 22 @ 2:0:11
 serio: gsc-ps2-mouse port at 0xf0108100 irq 22 @ 2:0:12

Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/input/serio/gscps2.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/input/serio/gscps2.c b/drivers/input/serio/gscps2.c
index ecba666afadb7..cca26e6f38b36 100644
--- a/drivers/input/serio/gscps2.c
+++ b/drivers/input/serio/gscps2.c
@@ -382,9 +382,9 @@ static int gscps2_probe(struct parisc_device *dev)
 		goto fail;
 #endif
 
-	printk(KERN_INFO "serio: %s port at 0x%p irq %d @ %s\n",
+	pr_info("serio: %s port at 0x%08lx irq %d @ %s\n",
 		ps2port->port->name,
-		ps2port->addr,
+		hpa,
 		ps2port->padev->irq,
 		ps2port->port->phys);
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 05/68] parisc: Fix HP SDC hpa address output

[Sasha Levin]

From: Helge Deller <deller@gmx.de>

[ Upstream commit c4bff35ca1bfba886da6223c9fed76a2b1382b8e ]

Show the hpa address of the HP SDC instead of a hashed value, e.g.:
HP SDC: HP SDC at 0xf0201000, IRQ 23 (NMI IRQ 24)

Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/input/serio/hp_sdc.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/input/serio/hp_sdc.c b/drivers/input/serio/hp_sdc.c
index 852858e5d8d08..92f541db98a09 100644
--- a/drivers/input/serio/hp_sdc.c
+++ b/drivers/input/serio/hp_sdc.c
@@ -887,8 +887,8 @@ static int __init hp_sdc_init(void)
 			"HP SDC NMI", &hp_sdc))
 		goto err2;
 
-	printk(KERN_INFO PREFIX "HP SDC at 0x%p, IRQ %d (NMI IRQ %d)\n",
-	       (void *)hp_sdc.base_io, hp_sdc.irq, hp_sdc.nmi);
+	pr_info(PREFIX "HP SDC at 0x%08lx, IRQ %d (NMI IRQ %d)\n",
+	       hp_sdc.base_io, hp_sdc.irq, hp_sdc.nmi);
 
 	hp_sdc_status_in8();
 	hp_sdc_data_in8();
-- 
2.20.1

[PATCH AUTOSEL 4.4 06/68] arm64: smp: Handle errors reported by the firmware

[Sasha Levin]

From: Suzuki K Poulose <Suzuki.Poulose@arm.com>

[ Upstream commit f357b3a7e17af7736d67d8267edc1ed3d1dd9391 ]

The __cpu_up() routine ignores the errors reported by the firmware
for a CPU bringup operation and looks for the error status set by the
booting CPU. If the CPU never entered the kernel, we could end up
in assuming stale error status, which otherwise would have been
set/cleared appropriately by the booting CPU.

Reported-by: Steve Capper <steve.capper@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/kernel/smp.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/kernel/smp.c b/arch/arm64/kernel/smp.c
index 03c0946b79d20..7e90f429f7e5c 100644
--- a/arch/arm64/kernel/smp.c
+++ b/arch/arm64/kernel/smp.c
@@ -115,6 +115,7 @@ int __cpu_up(unsigned int cpu, struct task_struct *idle)
 		}
 	} else {
 		pr_err("CPU%u: failed to boot: %d\n", cpu, ret);
+		return ret;
 	}
 
 	secondary_data.stack = NULL;
-- 
2.20.1

[PATCH AUTOSEL 4.4 07/68] PM / AVS: SmartReflex: NULL check before some freeing functions is not needed

[Sasha Levin]

From: Thomas Meyer <thomas@m3y3r.de>

[ Upstream commit 14d338a857f05f894ba3badd9e6d3039c68b8180 ]

NULL check before some freeing functions is not needed.

Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/power/avs/smartreflex.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/drivers/power/avs/smartreflex.c b/drivers/power/avs/smartreflex.c
index db9973bb53f19..ecc59798fd0aa 100644
--- a/drivers/power/avs/smartreflex.c
+++ b/drivers/power/avs/smartreflex.c
@@ -1001,8 +1001,7 @@ static int omap_sr_remove(struct platform_device *pdev)
 
 	if (sr_info->autocomp_active)
 		sr_stop_vddautocomp(sr_info);
-	if (sr_info->dbg_dir)
-		debugfs_remove_recursive(sr_info->dbg_dir);
+	debugfs_remove_recursive(sr_info->dbg_dir);
 
 	pm_runtime_disable(&pdev->dev);
 	list_del(&sr_info->node);
-- 
2.20.1

[PATCH AUTOSEL 4.4 08/68] ARM: ks8695: fix section mismatch warning

[Sasha Levin]

From: Arnd Bergmann <arnd@arndb.de>

[ Upstream commit 4aa64677330beeeed721b4b122884dabad845d66 ]

WARNING: vmlinux.o(.text+0x13250): Section mismatch in reference from the function acs5k_i2c_init() to the (unknown reference) .init.data:(unknown)
The function acs5k_i2c_init() references
the (unknown reference) __initdata (unknown).
This is often because acs5k_i2c_init lacks a __initdata
annotation or the annotation of (unknown) is wrong.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/mach-ks8695/board-acs5k.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/mach-ks8695/board-acs5k.c b/arch/arm/mach-ks8695/board-acs5k.c
index 9f9c0441a9175..e372609c48dd0 100644
--- a/arch/arm/mach-ks8695/board-acs5k.c
+++ b/arch/arm/mach-ks8695/board-acs5k.c
@@ -92,7 +92,7 @@ static struct i2c_board_info acs5k_i2c_devs[] __initdata = {
 	},
 };
 
-static void acs5k_i2c_init(void)
+static void __init acs5k_i2c_init(void)
 {
 	/* The gpio interface */
 	platform_device_register(&acs5k_i2c_device);
-- 
2.20.1

[PATCH AUTOSEL 4.4 09/68] ACPI / LPSS: Ignore acpi_device_fix_up_power() return value

[Sasha Levin]

From: Hans de Goede <hdegoede@redhat.com>

[ Upstream commit 1a2fa02f7489dc4d746f2a15fb77b3ce1affade8 ]

Ignore acpi_device_fix_up_power() return value. If we return an error
we end up with acpi_default_enumeration() still creating a platform-
device for the device and we end up with the device still being used
but without the special LPSS related handling which is not useful.

Specicifically ignoring the error fixes the touchscreen no longer
working after a suspend/resume on a Prowise PT301 tablet.

This tablet has a broken _PS0 method on the touchscreen's I2C controller,
causing acpi_device_fix_up_power() to fail, causing fallback to standard
platform-dev handling and specifically causing acpi_lpss_save/restore_ctx
to not run.

The I2C controllers _PS0 method does actually turn on the device, but then
does some more nonsense which fails when run during early boot trying to
use I2C opregion handling on another not-yet registered I2C controller.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/acpi/acpi_lpss.c | 7 +------
 1 file changed, 1 insertion(+), 6 deletions(-)

diff --git a/drivers/acpi/acpi_lpss.c b/drivers/acpi/acpi_lpss.c
index 572755e557d6a..e54e6170981b4 100644
--- a/drivers/acpi/acpi_lpss.c
+++ b/drivers/acpi/acpi_lpss.c
@@ -405,12 +405,7 @@ static int acpi_lpss_create_device(struct acpi_device *adev,
 	 * have _PS0 and _PS3 without _PSC (and no power resources), so
 	 * acpi_bus_init_power() will assume that the BIOS has put them into D0.
 	 */
-	ret = acpi_device_fix_up_power(adev);
-	if (ret) {
-		/* Skip the device, but continue the namespace scan. */
-		ret = 0;
-		goto err_out;
-	}
+	acpi_device_fix_up_power(adev);
 
 	adev->driver_data = pdata;
 	pdev = acpi_create_platform_device(adev);
-- 
2.20.1

[PATCH AUTOSEL 4.4 10/68] crypto: user - support incremental algorithm dumps

[Sasha Levin]

From: Eric Biggers <ebiggers@google.com>

[ Upstream commit 0ac6b8fb23c724b015d9ca70a89126e8d1563166 ]

CRYPTO_MSG_GETALG in NLM_F_DUMP mode sometimes doesn't return all
registered crypto algorithms, because it doesn't support incremental
dumps.  crypto_dump_report() only permits itself to be called once, yet
the netlink subsystem allocates at most ~64 KiB for the skb being dumped
to.  Thus only the first recvmsg() returns data, and it may only include
a subset of the crypto algorithms even if the user buffer passed to
recvmsg() is large enough to hold all of them.

Fix this by using one of the arguments in the netlink_callback structure
to keep track of the current position in the algorithm list.  Then
userspace can do multiple recvmsg() on the socket after sending the dump
request.  This is the way netlink dumps work elsewhere in the kernel;
it's unclear why this was different (probably just an oversight).

Also fix an integer overflow when calculating the dump buffer size hint.

Fixes: a38f7907b926 ("crypto: Add userspace configuration API")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 crypto/crypto_user.c | 37 ++++++++++++++++++++-----------------
 1 file changed, 20 insertions(+), 17 deletions(-)

diff --git a/crypto/crypto_user.c b/crypto/crypto_user.c
index b93c6db18ed3a..f18dc2d045c2a 100644
--- a/crypto/crypto_user.c
+++ b/crypto/crypto_user.c
@@ -257,30 +257,33 @@ static int crypto_report(struct sk_buff *in_skb, struct nlmsghdr *in_nlh,
 
 static int crypto_dump_report(struct sk_buff *skb, struct netlink_callback *cb)
 {
-	struct crypto_alg *alg;
+	const size_t start_pos = cb->args[0];
+	size_t pos = 0;
 	struct crypto_dump_info info;
-	int err;
-
-	if (cb->args[0])
-		goto out;
-
-	cb->args[0] = 1;
+	struct crypto_alg *alg;
+	int res;
 
 	info.in_skb = cb->skb;
 	info.out_skb = skb;
 	info.nlmsg_seq = cb->nlh->nlmsg_seq;
 	info.nlmsg_flags = NLM_F_MULTI;
 
+	down_read(&crypto_alg_sem);
 	list_for_each_entry(alg, &crypto_alg_list, cra_list) {
-		err = crypto_report_alg(alg, &info);
-		if (err)
-			goto out_err;
+		if (pos >= start_pos) {
+			res = crypto_report_alg(alg, &info);
+			if (res == -EMSGSIZE)
+				break;
+			if (res)
+				goto out;
+		}
+		pos++;
 	}
-
+	cb->args[0] = pos;
+	res = skb->len;
 out:
-	return skb->len;
-out_err:
-	return err;
+	up_read(&crypto_alg_sem);
+	return res;
 }
 
 static int crypto_dump_report_done(struct netlink_callback *cb)
@@ -498,7 +501,7 @@ static int crypto_user_rcv_msg(struct sk_buff *skb, struct nlmsghdr *nlh)
 	if ((type == (CRYPTO_MSG_GETALG - CRYPTO_MSG_BASE) &&
 	    (nlh->nlmsg_flags & NLM_F_DUMP))) {
 		struct crypto_alg *alg;
-		u16 dump_alloc = 0;
+		unsigned long dump_alloc = 0;
 
 		if (link->dump == NULL)
 			return -EINVAL;
@@ -506,16 +509,16 @@ static int crypto_user_rcv_msg(struct sk_buff *skb, struct nlmsghdr *nlh)
 		down_read(&crypto_alg_sem);
 		list_for_each_entry(alg, &crypto_alg_list, cra_list)
 			dump_alloc += CRYPTO_REPORT_MAXSIZE;
+		up_read(&crypto_alg_sem);
 
 		{
 			struct netlink_dump_control c = {
 				.dump = link->dump,
 				.done = link->done,
-				.min_dump_alloc = dump_alloc,
+				.min_dump_alloc = min(dump_alloc, 65535UL),
 			};
 			err = netlink_dump_start(crypto_nlsk, skb, nlh, &c);
 		}
-		up_read(&crypto_alg_sem);
 
 		return err;
 	}
-- 
2.20.1

[PATCH AUTOSEL 4.4 11/68] mwifiex: fix potential NULL dereference and use after free

[Sasha Levin]

From: Pan Bian <bianpan2016@163.com>

[ Upstream commit 1dcd9429212b98bea87fc6ec92fb50bf5953eb47 ]

There are two defects: (1) passing a NULL bss to
mwifiex_save_hidden_ssid_channels will result in NULL dereference,
(2) using bss after dropping the reference to it via cfg80211_put_bss.
To fix them, the patch moves the buggy code to the branch that bss is
not NULL and puts it before cfg80211_put_bss.

Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/mwifiex/scan.c | 18 ++++++++++--------
 1 file changed, 10 insertions(+), 8 deletions(-)

diff --git a/drivers/net/wireless/mwifiex/scan.c b/drivers/net/wireless/mwifiex/scan.c
index b3fa3e4bed052..39b78dc1bd92b 100644
--- a/drivers/net/wireless/mwifiex/scan.c
+++ b/drivers/net/wireless/mwifiex/scan.c
@@ -1873,15 +1873,17 @@ mwifiex_parse_single_response_buf(struct mwifiex_private *priv, u8 **bss_info,
 					    ETH_ALEN))
 					mwifiex_update_curr_bss_params(priv,
 								       bss);
-				cfg80211_put_bss(priv->wdev.wiphy, bss);
-			}
 
-			if ((chan->flags & IEEE80211_CHAN_RADAR) ||
-			    (chan->flags & IEEE80211_CHAN_NO_IR)) {
-				mwifiex_dbg(adapter, INFO,
-					    "radar or passive channel %d\n",
-					    channel);
-				mwifiex_save_hidden_ssid_channels(priv, bss);
+				if ((chan->flags & IEEE80211_CHAN_RADAR) ||
+				    (chan->flags & IEEE80211_CHAN_NO_IR)) {
+					mwifiex_dbg(adapter, INFO,
+						    "radar or passive channel %d\n",
+						    channel);
+					mwifiex_save_hidden_ssid_channels(priv,
+									  bss);
+				}
+
+				cfg80211_put_bss(priv->wdev.wiphy, bss);
 			}
 		}
 	} else {
-- 
2.20.1

[PATCH AUTOSEL 4.4 12/68] mwifiex: debugfs: correct histogram spacing, formatting

[Sasha Levin]

From: Brian Norris <briannorris@chromium.org>

[ Upstream commit 4cb777c64e030778c569f605398d7604d8aabc0f ]

Currently, snippets of this file look like:

rx rates (in Mbps): 0=1M   1=2M2=5.5M  3=11M   4=6M   5=9M  6=12M
7=18M  8=24M  9=36M  10=48M  11=54M12-27=MCS0-15(BW20) 28-43=MCS0-15(BW40)
44-53=MCS0-9(VHT:BW20)54-63=MCS0-9(VHT:BW40)64-73=MCS0-9(VHT:BW80)
...
noise_flr[--96dBm] = 22
noise_flr[--95dBm] = 149
noise_flr[--94dBm] = 9
noise_flr[--93dBm] = 2

We're missing some spaces, and we're adding a minus sign ('-') on values
that are already negative signed integers.

Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/mwifiex/debugfs.c | 14 ++++++--------
 1 file changed, 6 insertions(+), 8 deletions(-)

diff --git a/drivers/net/wireless/mwifiex/debugfs.c b/drivers/net/wireless/mwifiex/debugfs.c
index 45d97b64ef84b..f72c4f8853111 100644
--- a/drivers/net/wireless/mwifiex/debugfs.c
+++ b/drivers/net/wireless/mwifiex/debugfs.c
@@ -295,15 +295,13 @@ mwifiex_histogram_read(struct file *file, char __user *ubuf,
 		     "total samples = %d\n",
 		     atomic_read(&phist_data->num_samples));
 
-	p += sprintf(p, "rx rates (in Mbps): 0=1M   1=2M");
-	p += sprintf(p, "2=5.5M  3=11M   4=6M   5=9M  6=12M\n");
-	p += sprintf(p, "7=18M  8=24M  9=36M  10=48M  11=54M");
-	p += sprintf(p, "12-27=MCS0-15(BW20) 28-43=MCS0-15(BW40)\n");
+	p += sprintf(p,
+		     "rx rates (in Mbps): 0=1M   1=2M 2=5.5M  3=11M   4=6M   5=9M  6=12M\n"
+		     "7=18M  8=24M  9=36M  10=48M  11=54M 12-27=MCS0-15(BW20) 28-43=MCS0-15(BW40)\n");
 
 	if (ISSUPP_11ACENABLED(priv->adapter->fw_cap_info)) {
-		p += sprintf(p, "44-53=MCS0-9(VHT:BW20)");
-		p += sprintf(p, "54-63=MCS0-9(VHT:BW40)");
-		p += sprintf(p, "64-73=MCS0-9(VHT:BW80)\n\n");
+		p += sprintf(p,
+			     "44-53=MCS0-9(VHT:BW20) 54-63=MCS0-9(VHT:BW40) 64-73=MCS0-9(VHT:BW80)\n\n");
 	} else {
 		p += sprintf(p, "\n");
 	}
@@ -332,7 +330,7 @@ mwifiex_histogram_read(struct file *file, char __user *ubuf,
 	for (i = 0; i < MWIFIEX_MAX_NOISE_FLR; i++) {
 		value = atomic_read(&phist_data->noise_flr[i]);
 		if (value)
-			p += sprintf(p, "noise_flr[-%02ddBm] = %d\n",
+			p += sprintf(p, "noise_flr[%02ddBm] = %d\n",
 				(int)(i-128), value);
 	}
 	for (i = 0; i < MWIFIEX_MAX_SIG_STRENGTH; i++) {
-- 
2.20.1

[PATCH AUTOSEL 4.4 13/68] rtl818x: fix potential use after free

[Sasha Levin]

From: Pan Bian <bianpan2016@163.com>

[ Upstream commit afbb1947db94eacc5a13302eee88a9772fb78935 ]

entry is released via usb_put_urb just after calling usb_submit_urb.
However, entry is used if the submission fails, resulting in a use after
free bug. The patch fixes this.

Signed-off-by: Pan Bian <bianpan2016@163.com>
ACKed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/realtek/rtl818x/rtl8187/dev.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/realtek/rtl818x/rtl8187/dev.c b/drivers/net/wireless/realtek/rtl818x/rtl8187/dev.c
index b3691712df610..60e77eaa4ce94 100644
--- a/drivers/net/wireless/realtek/rtl818x/rtl8187/dev.c
+++ b/drivers/net/wireless/realtek/rtl818x/rtl8187/dev.c
@@ -446,12 +446,13 @@ static int rtl8187_init_urbs(struct ieee80211_hw *dev)
 		skb_queue_tail(&priv->rx_queue, skb);
 		usb_anchor_urb(entry, &priv->anchored);
 		ret = usb_submit_urb(entry, GFP_KERNEL);
-		usb_put_urb(entry);
 		if (ret) {
 			skb_unlink(skb, &priv->rx_queue);
 			usb_unanchor_urb(entry);
+			usb_put_urb(entry);
 			goto err;
 		}
+		usb_put_urb(entry);
 	}
 	return ret;
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 14/68] xfs: require both realtime inodes to mount

[Sasha Levin]

From: "Darrick J. Wong" <darrick.wong@oracle.com>

[ Upstream commit 64bafd2f1e484e27071e7584642005d56516cb77 ]

Since mkfs always formats the filesystem with the realtime bitmap and
summary inodes immediately after the root directory, we should expect
that both of them are present and loadable, even if there isn't a
realtime volume attached.  There's no reason to skip this if rbmino ==
NULLFSINO; in fact, this causes an immediate crash if the there /is/ a
realtime volume and someone writes to it.

Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Bill O'Donnell <billodo@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 fs/xfs/xfs_rtalloc.c | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/fs/xfs/xfs_rtalloc.c b/fs/xfs/xfs_rtalloc.c
index ab1bac6a3a1c0..919b6544b61a3 100644
--- a/fs/xfs/xfs_rtalloc.c
+++ b/fs/xfs/xfs_rtalloc.c
@@ -1225,13 +1225,11 @@ xfs_rtmount_inodes(
 	xfs_sb_t	*sbp;
 
 	sbp = &mp->m_sb;
-	if (sbp->sb_rbmino == NULLFSINO)
-		return 0;
 	error = xfs_iget(mp, NULL, sbp->sb_rbmino, 0, 0, &mp->m_rbmip);
 	if (error)
 		return error;
 	ASSERT(mp->m_rbmip != NULL);
-	ASSERT(sbp->sb_rsumino != NULLFSINO);
+
 	error = xfs_iget(mp, NULL, sbp->sb_rsumino, 0, 0, &mp->m_rsumip);
 	if (error) {
 		IRELE(mp->m_rbmip);
-- 
2.20.1

[PATCH AUTOSEL 4.4 15/68] ubi: Put MTD device after it is not used

[Sasha Levin]

From: Pan Bian <bianpan2016@163.com>

[ Upstream commit b95f83ab762dd6211351b9140f99f43644076ca8 ]

The MTD device reference is dropped via put_mtd_device, however its
field ->index is read and passed to ubi_msg. To fix this, the patch
moves the reference dropping after calling ubi_msg.

Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/mtd/ubi/build.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/mtd/ubi/build.c b/drivers/mtd/ubi/build.c
index c9f5ae424af75..ae8e55b4f6f93 100644
--- a/drivers/mtd/ubi/build.c
+++ b/drivers/mtd/ubi/build.c
@@ -1141,10 +1141,10 @@ int ubi_detach_mtd_dev(int ubi_num, int anyway)
 	ubi_wl_close(ubi);
 	ubi_free_internal_volumes(ubi);
 	vfree(ubi->vtbl);
-	put_mtd_device(ubi->mtd);
 	vfree(ubi->peb_buf);
 	vfree(ubi->fm_buf);
 	ubi_msg(ubi, "mtd%d is detached", ubi->mtd->index);
+	put_mtd_device(ubi->mtd);
 	put_device(&ubi->dev);
 	return 0;
 }
-- 
2.20.1

[PATCH AUTOSEL 4.4 16/68] ubi: Do not drop UBI device reference before using

[Sasha Levin]

From: Pan Bian <bianpan2016@163.com>

[ Upstream commit e542087701f09418702673631a908429feb3eae0 ]

The UBI device reference is dropped but then the device is used as a
parameter of ubi_err. The bug is introduced in changing ubi_err's
behavior. The old ubi_err does not require a UBI device as its first
parameter, but the new one does.

Fixes: 32608703310 ("UBI: Extend UBI layer debug/messaging capabilities")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/mtd/ubi/kapi.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/mtd/ubi/kapi.c b/drivers/mtd/ubi/kapi.c
index e844887732fbd..1db375caef71b 100644
--- a/drivers/mtd/ubi/kapi.c
+++ b/drivers/mtd/ubi/kapi.c
@@ -227,9 +227,9 @@ struct ubi_volume_desc *ubi_open_volume(int ubi_num, int vol_id, int mode)
 out_free:
 	kfree(desc);
 out_put_ubi:
-	ubi_put_device(ubi);
 	ubi_err(ubi, "cannot open device %d, volume %d, error %d",
 		ubi_num, vol_id, err);
+	ubi_put_device(ubi);
 	return ERR_PTR(err);
 }
 EXPORT_SYMBOL_GPL(ubi_open_volume);
-- 
2.20.1

[PATCH AUTOSEL 4.4 17/68] microblaze: adjust the help to the real behavior

[Sasha Levin]

From: Masahiro Yamada <yamada.masahiro@socionext.com>

[ Upstream commit bafcc61d998c1ca18f556d92a0e95335ac68c7da ]

"make ARCH=microblaze help" mentions simpleImage.<dt>.unstrip,
but it is not a real Make target. It does not work because Makefile
assumes "system.unstrip" is the name of DT.

$ make ARCH=microblaze CROSS_COMPILE=microblaze-linux- simpleImage.system.unstrip
  [ snip ]
make[1]: *** No rule to make target 'arch/microblaze/boot/dts/system.unstrip.dtb', needed by 'arch/microblaze/boot/dts/system.dtb'.  Stop.
make: *** [Makefile;1060: arch/microblaze/boot/dts] Error 2
make: *** Waiting for unfinished jobs....

simpleImage.<dt> works like a phony target that generates multiple
images. Reflect the real behavior. I removed the DT directory path
information because it is already explained a few lines below.

While I am here, I deleted the redundant *_defconfig explanation.

The top-level Makefile caters to list available defconfig files:

  mmu_defconfig            - Build for mmu
  nommu_defconfig          - Build for nommu

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/microblaze/Makefile | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/microblaze/Makefile b/arch/microblaze/Makefile
index 740f2b82a182a..5e1e18540a571 100644
--- a/arch/microblaze/Makefile
+++ b/arch/microblaze/Makefile
@@ -83,11 +83,11 @@ define archhelp
   echo '* linux.bin    - Create raw binary'
   echo '  linux.bin.gz - Create compressed raw binary'
   echo '  linux.bin.ub - Create U-Boot wrapped raw binary'
-  echo '  simpleImage.<dt> - ELF image with $(arch)/boot/dts/<dt>.dts linked in'
-  echo '                   - stripped elf with fdt blob'
-  echo '  simpleImage.<dt>.unstrip - full ELF image with fdt blob'
-  echo '  *_defconfig      - Select default config from arch/microblaze/configs'
-  echo ''
+  echo '  simpleImage.<dt> - Create the following images with <dt>.dtb linked in'
+  echo '                    simpleImage.<dt>        : raw image'
+  echo '                    simpleImage.<dt>.ub     : raw image with U-Boot header'
+  echo '                    simpleImage.<dt>.unstrip: ELF (identical to vmlinux)'
+  echo '                    simpleImage.<dt>.strip  : stripped ELF'
   echo '  Targets with <dt> embed a device tree blob inside the image'
   echo '  These targets support board with firmware that does not'
   echo '  support passing a device tree directly. Replace <dt> with the'
-- 
2.20.1

[PATCH AUTOSEL 4.4 18/68] microblaze: move "... is ready" messages to arch/microblaze/Makefile

[Sasha Levin]

From: Masahiro Yamada <yamada.masahiro@socionext.com>

[ Upstream commit 2e14f94cf4bc2f15ca5362e81ca3a987c79e3062 ]

To prepare for more fixes, move this to arch/microblaze/Makefile.
Otherwise, the same "... is ready" would be printed multiple times.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/microblaze/Makefile      | 2 ++
 arch/microblaze/boot/Makefile | 4 ----
 2 files changed, 2 insertions(+), 4 deletions(-)

diff --git a/arch/microblaze/Makefile b/arch/microblaze/Makefile
index 5e1e18540a571..491676a6cde57 100644
--- a/arch/microblaze/Makefile
+++ b/arch/microblaze/Makefile
@@ -75,9 +75,11 @@ archclean:
 
 linux.bin linux.bin.gz linux.bin.ub: vmlinux
 	$(Q)$(MAKE) $(build)=$(boot) $(boot)/$@
+	@echo 'Kernel: $(boot)/$@ is ready' ' (#'`cat .version`')'
 
 simpleImage.%: vmlinux
 	$(Q)$(MAKE) $(build)=$(boot) $(boot)/$@
+	@echo 'Kernel: $(boot)/$@ is ready' ' (#'`cat .version`')'
 
 define archhelp
   echo '* linux.bin    - Create raw binary'
diff --git a/arch/microblaze/boot/Makefile b/arch/microblaze/boot/Makefile
index 0f3fe6a151dce..22bed08ec7f28 100644
--- a/arch/microblaze/boot/Makefile
+++ b/arch/microblaze/boot/Makefile
@@ -8,15 +8,12 @@ OBJCOPYFLAGS := -R .note -R .comment -R .note.gnu.build-id -O binary
 
 $(obj)/linux.bin: vmlinux FORCE
 	$(call if_changed,objcopy)
-	@echo 'Kernel: $@ is ready' ' (#'`cat .version`')'
 
 $(obj)/linux.bin.ub: $(obj)/linux.bin FORCE
 	$(call if_changed,uimage)
-	@echo 'Kernel: $@ is ready' ' (#'`cat .version`')'
 
 $(obj)/linux.bin.gz: $(obj)/linux.bin FORCE
 	$(call if_changed,gzip)
-	@echo 'Kernel: $@ is ready' ' (#'`cat .version`')'
 
 quiet_cmd_cp = CP      $< $@$2
 	cmd_cp = cat $< >$@$2 || (rm -f $@ && echo false)
@@ -34,6 +31,5 @@ $(obj)/simpleImage.%: vmlinux FORCE
 	$(call if_changed,objcopy)
 	$(call if_changed,uimage)
 	$(call if_changed,strip,.strip)
-	@echo 'Kernel: $(UIMAGE_OUT) is ready' ' (#'`cat .version`')'
 
 clean-files += simpleImage.*.unstrip linux.bin.ub dts/*.dtb
-- 
2.20.1

[PATCH AUTOSEL 4.4 19/68] gpiolib: Fix return value of gpio_to_desc() stub if !GPIOLIB

[Sasha Levin]

From: Krzysztof Kozlowski <krzk@kernel.org>

[ Upstream commit c5510b8dafce5f3f5a039c9b262ebcae0092c462 ]

If CONFIG_GPOILIB is not set, the stub of gpio_to_desc() should return
the same type of error as regular version: NULL.  All the callers
compare the return value of gpio_to_desc() against NULL, so returned
ERR_PTR would be treated as non-error case leading to dereferencing of
error value.

Fixes: 79a9becda894 ("gpiolib: export descriptor-based GPIO interface")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 include/linux/gpio/consumer.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/include/linux/gpio/consumer.h b/include/linux/gpio/consumer.h
index fb0fde686cb1f..4a9838feb0866 100644
--- a/include/linux/gpio/consumer.h
+++ b/include/linux/gpio/consumer.h
@@ -398,7 +398,7 @@ static inline int gpiod_to_irq(const struct gpio_desc *desc)
 
 static inline struct gpio_desc *gpio_to_desc(unsigned gpio)
 {
-	return ERR_PTR(-EINVAL);
+	return NULL;
 }
 
 static inline int desc_to_gpio(const struct gpio_desc *desc)
-- 
2.20.1

[PATCH AUTOSEL 4.4 20/68] VSOCK: bind to random port for VMADDR_PORT_ANY

[Sasha Levin]

From: Lepton Wu <ytht.net@gmail.com>

[ Upstream commit 8236b08cf50f85bbfaf48910a0b3ee68318b7c4b ]

The old code always starts from fixed port for VMADDR_PORT_ANY. Sometimes
when VMM crashed, there is still orphaned vsock which is waiting for
close timer, then it could cause connection time out for new started VM
if they are trying to connect to same port with same guest cid since the
new packets could hit that orphaned vsock. We could also fix this by doing
more in vhost_vsock_reset_orphans, but any way, it should be better to start
from a random local port instead of a fixed one.

Signed-off-by: Lepton Wu <ytht.net@gmail.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/vmw_vsock/af_vsock.c | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

diff --git a/net/vmw_vsock/af_vsock.c b/net/vmw_vsock/af_vsock.c
index 7f1d166ce6128..412d56614fd5e 100644
--- a/net/vmw_vsock/af_vsock.c
+++ b/net/vmw_vsock/af_vsock.c
@@ -89,6 +89,7 @@
 #include <linux/mutex.h>
 #include <linux/net.h>
 #include <linux/poll.h>
+#include <linux/random.h>
 #include <linux/skbuff.h>
 #include <linux/smp.h>
 #include <linux/socket.h>
@@ -483,9 +484,13 @@ static void vsock_pending_work(struct work_struct *work)
 static int __vsock_bind_stream(struct vsock_sock *vsk,
 			       struct sockaddr_vm *addr)
 {
-	static u32 port = LAST_RESERVED_PORT + 1;
+	static u32 port = 0;
 	struct sockaddr_vm new_addr;
 
+	if (!port)
+		port = LAST_RESERVED_PORT + 1 +
+			prandom_u32_max(U32_MAX - LAST_RESERVED_PORT);
+
 	vsock_addr_init(&new_addr, addr->svm_cid, addr->svm_port);
 
 	if (addr->svm_port == VMADDR_PORT_ANY) {
-- 
2.20.1

[PATCH AUTOSEL 4.4 21/68] btrfs: only track ref_heads in delayed_ref_updates

[Sasha Levin]

From: Josef Bacik <jbacik@fb.com>

[ Upstream commit 158ffa364bf723fa1ef128060646d23dc3942994 ]

We use this number to figure out how many delayed refs to run, but
__btrfs_run_delayed_refs really only checks every time we need a new
delayed ref head, so we always run at least one ref head completely no
matter what the number of items on it.  Fix the accounting to only be
adjusted when we add/remove a ref head.

In addition to using this number to limit the number of delayed refs
run, a future patch is also going to use it to calculate the amount of
space required for delayed refs space reservation.

Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 fs/btrfs/delayed-ref.c | 3 ---
 1 file changed, 3 deletions(-)

diff --git a/fs/btrfs/delayed-ref.c b/fs/btrfs/delayed-ref.c
index e06dd75ad13f9..a2f165029ee62 100644
--- a/fs/btrfs/delayed-ref.c
+++ b/fs/btrfs/delayed-ref.c
@@ -193,8 +193,6 @@ static inline void drop_delayed_ref(struct btrfs_trans_handle *trans,
 	ref->in_tree = 0;
 	btrfs_put_delayed_ref(ref);
 	atomic_dec(&delayed_refs->num_entries);
-	if (trans->delayed_ref_updates)
-		trans->delayed_ref_updates--;
 }
 
 static bool merge_ref(struct btrfs_trans_handle *trans,
@@ -444,7 +442,6 @@ add_delayed_ref_tail_merge(struct btrfs_trans_handle *trans,
 add_tail:
 	list_add_tail(&ref->list, &href->ref_list);
 	atomic_inc(&root->num_entries);
-	trans->delayed_ref_updates++;
 	spin_unlock(&href->lock);
 	return ret;
 }
-- 
2.20.1

[PATCH AUTOSEL 4.4 22/68] xen/pciback: Check dev_data before using it

[Sasha Levin]

From: Ross Lagerwall <ross.lagerwall@citrix.com>

[ Upstream commit 1669907e3d1abfa3f7586e2d55dbbc117b5adba2 ]

If pcistub_init_device fails, the release function will be called with
dev_data set to NULL.  Check it before using it to avoid a NULL pointer
dereference.

Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/xen/xen-pciback/pci_stub.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/xen/xen-pciback/pci_stub.c b/drivers/xen/xen-pciback/pci_stub.c
index 258b7c3256499..47c6df53cabfb 100644
--- a/drivers/xen/xen-pciback/pci_stub.c
+++ b/drivers/xen/xen-pciback/pci_stub.c
@@ -104,7 +104,8 @@ static void pcistub_device_release(struct kref *kref)
 	 * is called from "unbind" which takes a device_lock mutex.
 	 */
 	__pci_reset_function_locked(dev);
-	if (pci_load_and_free_saved_state(dev, &dev_data->pci_saved_state))
+	if (dev_data &&
+	    pci_load_and_free_saved_state(dev, &dev_data->pci_saved_state))
 		dev_info(&dev->dev, "Could not reload PCI state\n");
 	else
 		pci_restore_state(dev);
-- 
2.20.1

[PATCH AUTOSEL 4.4 23/68] KVM: s390: unregister debug feature on failing arch init

[Sasha Levin]

From: Michael Mueller <mimu@linux.ibm.com>

[ Upstream commit 308c3e6673b012beecb96ef04cc65f4a0e7cdd99 ]

Make sure the debug feature and its allocated resources get
released upon unsuccessful architecture initialization.

A related indication of the issue will be reported as kernel
message.

Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20181130143215.69496-2-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/s390/kvm/kvm-s390.c | 17 ++++++++++++++---
 1 file changed, 14 insertions(+), 3 deletions(-)

diff --git a/arch/s390/kvm/kvm-s390.c b/arch/s390/kvm/kvm-s390.c
index 3e46f62d32adf..b4032d625d225 100644
--- a/arch/s390/kvm/kvm-s390.c
+++ b/arch/s390/kvm/kvm-s390.c
@@ -185,17 +185,28 @@ void kvm_arch_hardware_unsetup(void)
 
 int kvm_arch_init(void *opaque)
 {
+	int rc;
+
 	kvm_s390_dbf = debug_register("kvm-trace", 32, 1, 7 * sizeof(long));
 	if (!kvm_s390_dbf)
 		return -ENOMEM;
 
 	if (debug_register_view(kvm_s390_dbf, &debug_sprintf_view)) {
-		debug_unregister(kvm_s390_dbf);
-		return -ENOMEM;
+		rc = -ENOMEM;
+		goto out_debug_unreg;
 	}
 
 	/* Register floating interrupt controller interface. */
-	return kvm_register_device_ops(&kvm_flic_ops, KVM_DEV_TYPE_FLIC);
+	rc = kvm_register_device_ops(&kvm_flic_ops, KVM_DEV_TYPE_FLIC);
+	if (rc) {
+		pr_err("Failed to register FLIC rc=%d\n", rc);
+		goto out_debug_unreg;
+	}
+	return 0;
+
+out_debug_unreg:
+	debug_unregister(kvm_s390_dbf);
+	return rc;
 }
 
 void kvm_arch_exit(void)
-- 
2.20.1

[PATCH AUTOSEL 4.4 24/68] pinctrl: sh-pfc: sh7264: Fix PFCR3 and PFCR0 register configuration

[Sasha Levin]

From: Geert Uytterhoeven <geert+renesas@glider.be>

[ Upstream commit 1b99d0c80bbe1810572c2cb77b90f67886adfa8d ]

The Port F Control Register 3 (PFCR3) contains only a single field.
However, counting from left to right, it is the fourth field, not the
first field.
Insert the missing dummy configuration values (3 fields of 16 values) to
fix this.

The descriptor for the Port F Control Register 0 (PFCR0) lacks the
description for the 4th field (PF0 Mode, PF0MD[2:0]).
Add the missing configuration values to fix this.

Fixes: a8d42fc4217b1ea1 ("sh-pfc: Add sh7264 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pinctrl/sh-pfc/pfc-sh7264.c | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)

diff --git a/drivers/pinctrl/sh-pfc/pfc-sh7264.c b/drivers/pinctrl/sh-pfc/pfc-sh7264.c
index 8070765311dbf..e1c34e19222ee 100644
--- a/drivers/pinctrl/sh-pfc/pfc-sh7264.c
+++ b/drivers/pinctrl/sh-pfc/pfc-sh7264.c
@@ -1716,6 +1716,9 @@ static const struct pinmux_cfg_reg pinmux_config_regs[] = {
 	},
 
 	{ PINMUX_CFG_REG("PFCR3", 0xfffe38a8, 16, 4) {
+		0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+		0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+		0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
 		PF12MD_000, PF12MD_001, 0, PF12MD_011,
 		PF12MD_100, PF12MD_101, 0, 0,
 		0, 0, 0, 0, 0, 0, 0, 0 }
@@ -1759,8 +1762,10 @@ static const struct pinmux_cfg_reg pinmux_config_regs[] = {
 		0, 0, 0, 0, 0, 0, 0, 0,
 		PF1MD_000, PF1MD_001, PF1MD_010, PF1MD_011,
 		PF1MD_100, PF1MD_101, 0, 0,
-		0, 0, 0, 0, 0, 0, 0, 0
-	 }
+		0, 0, 0, 0, 0, 0, 0, 0,
+		PF0MD_000, PF0MD_001, PF0MD_010, PF0MD_011,
+		PF0MD_100, PF0MD_101, 0, 0,
+		0, 0, 0, 0, 0, 0, 0, 0 }
 	},
 
 	{ PINMUX_CFG_REG("PFIOR0", 0xfffe38b2, 16, 1) {
-- 
2.20.1

[PATCH AUTOSEL 4.4 25/68] pinctrl: sh-pfc: sh7734: Fix shifted values in IPSR10

[Sasha Levin]

From: Geert Uytterhoeven <geert+renesas@glider.be>

[ Upstream commit 054f2400f706327f96770219c3065b5131f8f154 ]

Some values in the Peripheral Function Select Register 10 descriptor are
shifted by one position, which may cause a peripheral function to be
programmed incorrectly.

Fixing this makes all HSCIF0 pins use Function 4 (value 3), like was
already the case for the HSCK0 pin in field IP10[5:3].

Fixes: ac1ebc2190f575fc ("sh-pfc: Add sh7734 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pinctrl/sh-pfc/pfc-sh7734.c | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)

diff --git a/drivers/pinctrl/sh-pfc/pfc-sh7734.c b/drivers/pinctrl/sh-pfc/pfc-sh7734.c
index 9842bb1067969..c691b2e343746 100644
--- a/drivers/pinctrl/sh-pfc/pfc-sh7734.c
+++ b/drivers/pinctrl/sh-pfc/pfc-sh7734.c
@@ -2218,22 +2218,22 @@ static const struct pinmux_cfg_reg pinmux_config_regs[] = {
 	    /* IP10_22 [1] */
 		FN_CAN_CLK_A, FN_RX4_D,
 	    /* IP10_21_19 [3] */
-		FN_AUDIO_CLKOUT, FN_TX1_E, FN_HRTS0_C, FN_FSE_B,
-		FN_LCD_M_DISP_B, 0, 0, 0,
+		FN_AUDIO_CLKOUT, FN_TX1_E, 0, FN_HRTS0_C, FN_FSE_B,
+		FN_LCD_M_DISP_B, 0, 0,
 	    /* IP10_18_16 [3] */
-		FN_AUDIO_CLKC, FN_SCK1_E, FN_HCTS0_C, FN_FRB_B,
-		FN_LCD_VEPWC_B, 0, 0, 0,
+		FN_AUDIO_CLKC, FN_SCK1_E, 0, FN_HCTS0_C, FN_FRB_B,
+		FN_LCD_VEPWC_B, 0, 0,
 	    /* IP10_15 [1] */
 		FN_AUDIO_CLKB_A, FN_LCD_CLK_B,
 	    /* IP10_14_12 [3] */
 		FN_AUDIO_CLKA_A, FN_VI1_CLK_B, FN_SCK1_D, FN_IECLK_B,
 		FN_LCD_FLM_B, 0, 0, 0,
 	    /* IP10_11_9 [3] */
-		FN_SSI_SDATA3, FN_VI1_7_B, FN_HTX0_C, FN_FWE_B,
-		FN_LCD_CL2_B, 0, 0, 0,
+		FN_SSI_SDATA3, FN_VI1_7_B, 0, FN_HTX0_C, FN_FWE_B,
+		FN_LCD_CL2_B, 0, 0,
 	    /* IP10_8_6 [3] */
-		FN_SSI_SDATA2, FN_VI1_6_B, FN_HRX0_C, FN_FRE_B,
-		FN_LCD_CL1_B, 0, 0, 0,
+		FN_SSI_SDATA2, FN_VI1_6_B, 0, FN_HRX0_C, FN_FRE_B,
+		FN_LCD_CL1_B, 0, 0,
 	    /* IP10_5_3 [3] */
 		FN_SSI_WS23, FN_VI1_5_B, FN_TX1_D, FN_HSCK0_C, FN_FALE_B,
 		FN_LCD_DON_B, 0, 0, 0,
-- 
2.20.1

[PATCH AUTOSEL 4.4 26/68] HID: doc: fix wrong data structure reference for UHID_OUTPUT

[Sasha Levin]

From: Peter Hutterer <peter.hutterer@who-t.net>

[ Upstream commit 46b14eef59a8157138dc02f916a7f97c73b3ec53 ]

Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 Documentation/hid/uhid.txt | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/Documentation/hid/uhid.txt b/Documentation/hid/uhid.txt
index c8656dd029a91..958fff9453044 100644
--- a/Documentation/hid/uhid.txt
+++ b/Documentation/hid/uhid.txt
@@ -160,7 +160,7 @@ them but you should handle them according to your needs.
   UHID_OUTPUT:
   This is sent if the HID device driver wants to send raw data to the I/O
   device on the interrupt channel. You should read the payload and forward it to
-  the device. The payload is of type "struct uhid_data_req".
+  the device. The payload is of type "struct uhid_output_req".
   This may be received even though you haven't received UHID_OPEN, yet.
 
   UHID_GET_REPORT:
-- 
2.20.1

[PATCH AUTOSEL 4.4 27/68] gfs2: take jdata unstuff into account in do_grow

[Sasha Levin]

From: Bob Peterson <rpeterso@redhat.com>

[ Upstream commit bc0205612bbd4dd4026d4ba6287f5643c37366ec ]

Before this patch, function do_grow would not reserve enough journal
blocks in the transaction to unstuff jdata files while growing them.
This patch adds the logic to add one more block if the file to grow
is jdata.

Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Reviewed-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 fs/gfs2/bmap.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/fs/gfs2/bmap.c b/fs/gfs2/bmap.c
index 09476bb8f6cd0..f0302e09eff99 100644
--- a/fs/gfs2/bmap.c
+++ b/fs/gfs2/bmap.c
@@ -1235,6 +1235,8 @@ static int do_grow(struct inode *inode, u64 size)
 	}
 
 	error = gfs2_trans_begin(sdp, RES_DINODE + RES_STATFS + RES_RG_BIT +
+				 (unstuff &&
+				  gfs2_is_jdata(ip) ? RES_JDATA : 0) +
 				 (sdp->sd_args.ar_quota == GFS2_QUOTA_OFF ?
 				  0 : RES_QUOTA), 0);
 	if (error)
-- 
2.20.1

[PATCH AUTOSEL 4.4 28/68] xfs: Align compat attrlist_by_handle with native implementation.

[Sasha Levin]

From: Nick Bowler <nbowler@draconx.ca>

[ Upstream commit c456d64449efe37da50832b63d91652a85ea1d20 ]

While inspecting the ioctl implementations, I noticed that the compat
implementation of XFS_IOC_ATTRLIST_BY_HANDLE does not do exactly the
same thing as the native implementation.  Specifically, the "cursor"
does not appear to be written out to userspace on the compat path,
like it is on the native path.

This adjusts the compat implementation to copy out the cursor just
like the native implementation does.  The attrlist cursor does not
require any special compat handling.  This fixes xfstests xfs/269
on both IA-32 and x32 userspace, when running on an amd64 kernel.

Signed-off-by: Nick Bowler <nbowler@draconx.ca>
Fixes: 0facef7fb053b ("xfs: in _attrlist_by_handle, copy the cursor back to userspace")
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 fs/xfs/xfs_ioctl32.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/fs/xfs/xfs_ioctl32.c b/fs/xfs/xfs_ioctl32.c
index 1a05d8ae327db..e7372cef5ac33 100644
--- a/fs/xfs/xfs_ioctl32.c
+++ b/fs/xfs/xfs_ioctl32.c
@@ -346,6 +346,7 @@ xfs_compat_attrlist_by_handle(
 {
 	int			error;
 	attrlist_cursor_kern_t	*cursor;
+	compat_xfs_fsop_attrlist_handlereq_t __user *p = arg;
 	compat_xfs_fsop_attrlist_handlereq_t al_hreq;
 	struct dentry		*dentry;
 	char			*kbuf;
@@ -380,6 +381,11 @@ xfs_compat_attrlist_by_handle(
 	if (error)
 		goto out_kfree;
 
+	if (copy_to_user(&p->pos, cursor, sizeof(attrlist_cursor_kern_t))) {
+		error = -EFAULT;
+		goto out_kfree;
+	}
+
 	if (copy_to_user(compat_ptr(al_hreq.buffer), kbuf, al_hreq.buflen))
 		error = -EFAULT;
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 29/68] IB/qib: Fix an error code in qib_sdma_verbs_send()

[Sasha Levin]

From: Dan Carpenter <dan.carpenter@oracle.com>

[ Upstream commit 5050ae5fa3d54c8e83e1e447cc7e3591110a7f57 ]

We accidentally return success on this error path.

Fixes: f931551bafe1 ("IB/qib: Add new qib driver for QLogic PCIe InfiniBand adapters")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/infiniband/hw/qib/qib_sdma.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/infiniband/hw/qib/qib_sdma.c b/drivers/infiniband/hw/qib/qib_sdma.c
index c6d6a54d2e19d..1c9a3e8752012 100644
--- a/drivers/infiniband/hw/qib/qib_sdma.c
+++ b/drivers/infiniband/hw/qib/qib_sdma.c
@@ -597,8 +597,10 @@ int qib_sdma_verbs_send(struct qib_pportdata *ppd,
 		dw = (len + 3) >> 2;
 		addr = dma_map_single(&ppd->dd->pcidev->dev, sge->vaddr,
 				      dw << 2, DMA_TO_DEVICE);
-		if (dma_mapping_error(&ppd->dd->pcidev->dev, addr))
+		if (dma_mapping_error(&ppd->dd->pcidev->dev, addr)) {
+			ret = -ENOMEM;
 			goto unmap;
+		}
 		sdmadesc[0] = 0;
 		make_sdma_desc(ppd, sdmadesc, (u64) addr, dw, dwoffset);
 		/* SDmaUseLargeBuf has to be set in every descriptor */
-- 
2.20.1

[PATCH AUTOSEL 4.4 30/68] powerpc/book3s/32: fix number of bats in p/v_block_mapped()

[Sasha Levin]

From: Christophe Leroy <christophe.leroy@c-s.fr>

[ Upstream commit e93ba1b7eb5b188c749052df7af1c90821c5f320 ]

This patch fixes the loop in p_block_mapped() and v_block_mapped()
to scan the entire bat_addrs[] array.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/powerpc/mm/ppc_mmu_32.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/powerpc/mm/ppc_mmu_32.c b/arch/powerpc/mm/ppc_mmu_32.c
index 6b2f3e457171a..ae0f157d201c6 100644
--- a/arch/powerpc/mm/ppc_mmu_32.c
+++ b/arch/powerpc/mm/ppc_mmu_32.c
@@ -52,7 +52,7 @@ struct batrange {		/* stores address ranges mapped by BATs */
 phys_addr_t v_mapped_by_bats(unsigned long va)
 {
 	int b;
-	for (b = 0; b < 4; ++b)
+	for (b = 0; b < ARRAY_SIZE(bat_addrs); ++b)
 		if (va >= bat_addrs[b].start && va < bat_addrs[b].limit)
 			return bat_addrs[b].phys + (va - bat_addrs[b].start);
 	return 0;
@@ -64,7 +64,7 @@ phys_addr_t v_mapped_by_bats(unsigned long va)
 unsigned long p_mapped_by_bats(phys_addr_t pa)
 {
 	int b;
-	for (b = 0; b < 4; ++b)
+	for (b = 0; b < ARRAY_SIZE(bat_addrs); ++b)
 		if (pa >= bat_addrs[b].phys
 	    	    && pa < (bat_addrs[b].limit-bat_addrs[b].start)
 		              +bat_addrs[b].phys)
-- 
2.20.1

[PATCH AUTOSEL 4.4 31/68] powerpc/xmon: fix dump_segments()

[Sasha Levin]

From: Christophe Leroy <christophe.leroy@c-s.fr>

[ Upstream commit 32c8c4c621897199e690760c2d57054f8b84b6e6 ]

mfsrin() takes segment num from bits 31-28 (IBM bits 0-3).

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Clarify bit numbering]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/powerpc/xmon/xmon.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/powerpc/xmon/xmon.c b/arch/powerpc/xmon/xmon.c
index 83619ebede93d..dc2ebc20a96f8 100644
--- a/arch/powerpc/xmon/xmon.c
+++ b/arch/powerpc/xmon/xmon.c
@@ -2840,7 +2840,7 @@ void dump_segments(void)
 
 	printf("sr0-15 =");
 	for (i = 0; i < 16; ++i)
-		printf(" %x", mfsrin(i));
+		printf(" %x", mfsrin(i << 28));
 	printf("\n");
 }
 #endif
-- 
2.20.1

[PATCH AUTOSEL 4.4 32/68] drivers/regulator: fix a missing check of return value

[Sasha Levin]

From: Kangjie Lu <kjlu@umn.edu>

[ Upstream commit 966e927bf8cc6a44f8b72582a1d6d3ffc73b12ad ]

If palmas_smps_read() fails, we should not use the read data in "reg"
which may contain random value. The fix inserts a check for the return
value of palmas_smps_read(): If it fails, we return the error code
upstream and stop using "reg".

Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/regulator/palmas-regulator.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/regulator/palmas-regulator.c b/drivers/regulator/palmas-regulator.c
index 8217613807d37..4a4766c43e616 100644
--- a/drivers/regulator/palmas-regulator.c
+++ b/drivers/regulator/palmas-regulator.c
@@ -435,13 +435,16 @@ static int palmas_ldo_write(struct palmas *palmas, unsigned int reg,
 static int palmas_set_mode_smps(struct regulator_dev *dev, unsigned int mode)
 {
 	int id = rdev_get_id(dev);
+	int ret;
 	struct palmas_pmic *pmic = rdev_get_drvdata(dev);
 	struct palmas_pmic_driver_data *ddata = pmic->palmas->pmic_ddata;
 	struct palmas_regs_info *rinfo = &ddata->palmas_regs_info[id];
 	unsigned int reg;
 	bool rail_enable = true;
 
-	palmas_smps_read(pmic->palmas, rinfo->ctrl_addr, &reg);
+	ret = palmas_smps_read(pmic->palmas, rinfo->ctrl_addr, &reg);
+	if (ret)
+		return ret;
 
 	reg &= ~PALMAS_SMPS12_CTRL_MODE_ACTIVE_MASK;
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 33/68] serial: max310x: Fix tx_empty() callback

[Sasha Levin]

From: Alexander Shiyan <shc_work@mail.ru>

[ Upstream commit a8da3c7873ea57acb8f9cea58c0af477522965aa ]

Function max310x_tx_empty() accesses the IRQSTS register, which is
cleared by IC when reading, so if there is an interrupt status, we
will lose it. This patch implement the transmitter check only by
the current FIFO level.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/tty/serial/max310x.c | 7 ++-----
 1 file changed, 2 insertions(+), 5 deletions(-)

diff --git a/drivers/tty/serial/max310x.c b/drivers/tty/serial/max310x.c
index a66fb7afecc71..e13e95733fa3c 100644
--- a/drivers/tty/serial/max310x.c
+++ b/drivers/tty/serial/max310x.c
@@ -763,12 +763,9 @@ static void max310x_start_tx(struct uart_port *port)
 
 static unsigned int max310x_tx_empty(struct uart_port *port)
 {
-	unsigned int lvl, sts;
+	u8 lvl = max310x_port_read(port, MAX310X_TXFIFOLVL_REG);
 
-	lvl = max310x_port_read(port, MAX310X_TXFIFOLVL_REG);
-	sts = max310x_port_read(port, MAX310X_IRQSTS_REG);
-
-	return ((sts & MAX310X_IRQ_TXEMPTY_BIT) && !lvl) ? TIOCSER_TEMT : 0;
+	return lvl ? 0 : TIOCSER_TEMT;
 }
 
 static unsigned int max310x_get_mctrl(struct uart_port *port)
-- 
2.20.1

[PATCH AUTOSEL 4.4 34/68] openrisc: Fix broken paths to arch/or32

[Sasha Levin]

From: Geert Uytterhoeven <geert@linux-m68k.org>

[ Upstream commit 57ce8ba0fd3a95bf29ed741df1c52bd591bf43ff ]

OpenRISC was mainlined as "openrisc", not "or32".
vmlinux.lds is generated from vmlinux.lds.S.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/openrisc/kernel/entry.S | 2 +-
 arch/openrisc/kernel/head.S  | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/openrisc/kernel/entry.S b/arch/openrisc/kernel/entry.S
index fec8bf97d8064..c17e8451d9978 100644
--- a/arch/openrisc/kernel/entry.S
+++ b/arch/openrisc/kernel/entry.S
@@ -179,7 +179,7 @@ handler:							;\
  *	 occured. in fact they never do. if you need them use
  *	 values saved on stack (for SPR_EPC, SPR_ESR) or content
  *       of r4 (for SPR_EEAR). for details look at EXCEPTION_HANDLE()
- *       in 'arch/or32/kernel/head.S'
+ *       in 'arch/openrisc/kernel/head.S'
  */
 
 /* =====================================================[ exceptions] === */
diff --git a/arch/openrisc/kernel/head.S b/arch/openrisc/kernel/head.S
index f14793306b03f..98dd6860bc0b9 100644
--- a/arch/openrisc/kernel/head.S
+++ b/arch/openrisc/kernel/head.S
@@ -1596,7 +1596,7 @@ _string_esr_irq_bug:
 
 /*
  * .data section should be page aligned
- *	(look into arch/or32/kernel/vmlinux.lds)
+ *	(look into arch/openrisc/kernel/vmlinux.lds.S)
  */
 	.section .data,"aw"
 	.align	8192
-- 
2.20.1

[PATCH AUTOSEL 4.4 35/68] RDMA/srp: Propagate ib_post_send() failures to the SCSI mid-layer

[Sasha Levin]

From: Bart Van Assche <bvanassche@acm.org>

[ Upstream commit 2ee00f6a98c36f7e4ba07cc33f24cc5a69060cc9 ]

This patch avoids that the SCSI mid-layer keeps retrying forever if
ib_post_send() fails. This was discovered while testing immediate
data support and passing a too large num_sge value to ib_post_send().

Cc: Sergey Gorenko <sergeygo@mellanox.com>
Cc: Max Gurtovoy <maxg@mellanox.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/infiniband/ulp/srp/ib_srp.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/infiniband/ulp/srp/ib_srp.c b/drivers/infiniband/ulp/srp/ib_srp.c
index 3dbc3ed263c21..3b4188efc2835 100644
--- a/drivers/infiniband/ulp/srp/ib_srp.c
+++ b/drivers/infiniband/ulp/srp/ib_srp.c
@@ -2135,6 +2135,7 @@ static int srp_queuecommand(struct Scsi_Host *shost, struct scsi_cmnd *scmnd)
 
 	if (srp_post_send(ch, iu, len)) {
 		shost_printk(KERN_ERR, target->scsi_host, PFX "Send failed\n");
+		scmnd->result = DID_ERROR << 16;
 		goto err_unmap;
 	}
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 36/68] scsi: qla2xxx: deadlock by configfs_depend_item

[Sasha Levin]

From: Anatoliy Glagolev <glagolig@gmail.com>

[ Upstream commit 17b18eaa6f59044a5172db7d07149e31ede0f920 ]

The intent of invoking configfs_depend_item in commit 7474f52a82d51
("tcm_qla2xxx: Perform configfs depend/undepend for base_tpg")
was to prevent a physical Fibre Channel port removal when
virtual (NPIV) ports announced through that physical port are active.
The change does not work as expected: it makes enabled physical port
dependent on target configfs subsystem (the port's parent), something
the configfs guarantees anyway.

Besides, scheduling work in a worker thread and waiting for the work's
completion is not really a valid workaround for the requirement not to call
configfs_depend_item from a configfs callback: the call occasionally
deadlocks.

Thus, removing configfs_depend_item calls does not break anything and fixes
the deadlock problem.

Signed-off-by: Anatoliy Glagolev <glagolig@gmail.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/qla2xxx/tcm_qla2xxx.c | 48 +++++-------------------------
 drivers/scsi/qla2xxx/tcm_qla2xxx.h |  3 --
 2 files changed, 8 insertions(+), 43 deletions(-)

diff --git a/drivers/scsi/qla2xxx/tcm_qla2xxx.c b/drivers/scsi/qla2xxx/tcm_qla2xxx.c
index 81af294f15a7d..b1233ce6cb475 100644
--- a/drivers/scsi/qla2xxx/tcm_qla2xxx.c
+++ b/drivers/scsi/qla2xxx/tcm_qla2xxx.c
@@ -793,38 +793,14 @@ static ssize_t tcm_qla2xxx_tpg_enable_show(struct config_item *item,
 			atomic_read(&tpg->lport_tpg_enabled));
 }
 
-static void tcm_qla2xxx_depend_tpg(struct work_struct *work)
-{
-	struct tcm_qla2xxx_tpg *base_tpg = container_of(work,
-				struct tcm_qla2xxx_tpg, tpg_base_work);
-	struct se_portal_group *se_tpg = &base_tpg->se_tpg;
-	struct scsi_qla_host *base_vha = base_tpg->lport->qla_vha;
-
-	if (!target_depend_item(&se_tpg->tpg_group.cg_item)) {
-		atomic_set(&base_tpg->lport_tpg_enabled, 1);
-		qlt_enable_vha(base_vha);
-	}
-	complete(&base_tpg->tpg_base_comp);
-}
-
-static void tcm_qla2xxx_undepend_tpg(struct work_struct *work)
-{
-	struct tcm_qla2xxx_tpg *base_tpg = container_of(work,
-				struct tcm_qla2xxx_tpg, tpg_base_work);
-	struct se_portal_group *se_tpg = &base_tpg->se_tpg;
-	struct scsi_qla_host *base_vha = base_tpg->lport->qla_vha;
-
-	if (!qlt_stop_phase1(base_vha->vha_tgt.qla_tgt)) {
-		atomic_set(&base_tpg->lport_tpg_enabled, 0);
-		target_undepend_item(&se_tpg->tpg_group.cg_item);
-	}
-	complete(&base_tpg->tpg_base_comp);
-}
-
 static ssize_t tcm_qla2xxx_tpg_enable_store(struct config_item *item,
 		const char *page, size_t count)
 {
 	struct se_portal_group *se_tpg = to_tpg(item);
+	struct se_wwn *se_wwn = se_tpg->se_tpg_wwn;
+	struct tcm_qla2xxx_lport *lport = container_of(se_wwn,
+			struct tcm_qla2xxx_lport, lport_wwn);
+	struct scsi_qla_host *vha = lport->qla_vha;
 	struct tcm_qla2xxx_tpg *tpg = container_of(se_tpg,
 			struct tcm_qla2xxx_tpg, se_tpg);
 	unsigned long op;
@@ -843,24 +819,16 @@ static ssize_t tcm_qla2xxx_tpg_enable_store(struct config_item *item,
 		if (atomic_read(&tpg->lport_tpg_enabled))
 			return -EEXIST;
 
-		INIT_WORK(&tpg->tpg_base_work, tcm_qla2xxx_depend_tpg);
+		atomic_set(&tpg->lport_tpg_enabled, 1);
+		qlt_enable_vha(vha);
 	} else {
 		if (!atomic_read(&tpg->lport_tpg_enabled))
 			return count;
 
-		INIT_WORK(&tpg->tpg_base_work, tcm_qla2xxx_undepend_tpg);
+		atomic_set(&tpg->lport_tpg_enabled, 0);
+		qlt_stop_phase1(vha->vha_tgt.qla_tgt);
 	}
-	init_completion(&tpg->tpg_base_comp);
-	schedule_work(&tpg->tpg_base_work);
-	wait_for_completion(&tpg->tpg_base_comp);
 
-	if (op) {
-		if (!atomic_read(&tpg->lport_tpg_enabled))
-			return -ENODEV;
-	} else {
-		if (atomic_read(&tpg->lport_tpg_enabled))
-			return -EPERM;
-	}
 	return count;
 }
 
diff --git a/drivers/scsi/qla2xxx/tcm_qla2xxx.h b/drivers/scsi/qla2xxx/tcm_qla2xxx.h
index 3bbf4cb6fd97e..344f4eab5403c 100644
--- a/drivers/scsi/qla2xxx/tcm_qla2xxx.h
+++ b/drivers/scsi/qla2xxx/tcm_qla2xxx.h
@@ -47,9 +47,6 @@ struct tcm_qla2xxx_tpg {
 	struct tcm_qla2xxx_tpg_attrib tpg_attrib;
 	/* Returned by tcm_qla2xxx_make_tpg() */
 	struct se_portal_group se_tpg;
-	/* Items for dealing with configfs_depend_item */
-	struct completion tpg_base_comp;
-	struct work_struct tpg_base_work;
 };
 
 struct tcm_qla2xxx_fc_loopid {
-- 
2.20.1

[PATCH AUTOSEL 4.4 37/68] scsi: csiostor: fix incorrect dma device in case of vport

[Sasha Levin]

From: Varun Prakash <varun@chelsio.com>

[ Upstream commit 9934613edcb40b92a216122876cd3b7e76d08390 ]

In case of ->vport_create() call scsi_add_host_with_dma() instead of
scsi_add_host() to pass correct dma device.

Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/csiostor/csio_init.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/scsi/csiostor/csio_init.c b/drivers/scsi/csiostor/csio_init.c
index dbe416ff46c27..776b992786881 100644
--- a/drivers/scsi/csiostor/csio_init.c
+++ b/drivers/scsi/csiostor/csio_init.c
@@ -648,7 +648,7 @@ csio_shost_init(struct csio_hw *hw, struct device *dev,
 	if (csio_lnode_init(ln, hw, pln))
 		goto err_shost_put;
 
-	if (scsi_add_host(shost, dev))
+	if (scsi_add_host_with_dma(shost, dev, &hw->pdev->dev))
 		goto err_lnode_exit;
 
 	return ln;
-- 
2.20.1

[PATCH AUTOSEL 4.4 38/68] ath6kl: Only use match sets when firmware supports it

[Sasha Levin]

From: Kyle Roeschley <kyle.roeschley@ni.com>

[ Upstream commit fb376a495fbdb886f38cfaf5a3805401b9e46f13 ]

Commit dd45b7598f1c ("ath6kl: Include match ssid list in scheduled scan")
merged the probed and matched SSID lists before sending them to the
firmware. In the process, it assumed match set support is always available
in ath6kl_set_probed_ssids, which breaks scans for hidden SSIDs. Now, check
that the firmware supports matching SSIDs in scheduled scans before setting
MATCH_SSID_FLAG.

Fixes: dd45b7598f1c ("ath6kl: Include match ssid list in scheduled scan")
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath6kl/cfg80211.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/wireless/ath/ath6kl/cfg80211.c b/drivers/net/wireless/ath/ath6kl/cfg80211.c
index 81ac8c59f0ecd..2b79815f59093 100644
--- a/drivers/net/wireless/ath/ath6kl/cfg80211.c
+++ b/drivers/net/wireless/ath/ath6kl/cfg80211.c
@@ -932,7 +932,7 @@ static int ath6kl_set_probed_ssids(struct ath6kl *ar,
 		else
 			ssid_list[i].flag = ANY_SSID_FLAG;
 
-		if (n_match_ssid == 0)
+		if (ar->wiphy->max_match_sets != 0 && n_match_ssid == 0)
 			ssid_list[i].flag |= MATCH_SSID_FLAG;
 	}
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 39/68] ath6kl: Fix off by one error in scan completion

[Sasha Levin]

From: Kyle Roeschley <kyle.roeschley@ni.com>

[ Upstream commit 5803c12816c43bd09e5f4247dd9313c2d9a2c41b ]

When ath6kl was reworked to share code between regular and scheduled scans
in commit 3b8ffc6a22ba ("ath6kl: Configure probed SSID list consistently"),
probed SSID entry changed from 1-index to 0-indexed. However,
ath6kl_cfg80211_scan_complete_event() was missed in that change. Fix its
indexing so that we correctly clear out the probed SSID list.

Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath6kl/cfg80211.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/wireless/ath/ath6kl/cfg80211.c b/drivers/net/wireless/ath/ath6kl/cfg80211.c
index 2b79815f59093..7653fa47508bb 100644
--- a/drivers/net/wireless/ath/ath6kl/cfg80211.c
+++ b/drivers/net/wireless/ath/ath6kl/cfg80211.c
@@ -1083,7 +1083,7 @@ void ath6kl_cfg80211_scan_complete_event(struct ath6kl_vif *vif, bool aborted)
 	if (vif->scan_req->n_ssids && vif->scan_req->ssids[0].ssid_len) {
 		for (i = 0; i < vif->scan_req->n_ssids; i++) {
 			ath6kl_wmi_probedssid_cmd(ar->wmi, vif->fw_vif_idx,
-						  i + 1, DISABLE_SSID_FLAG,
+						  i, DISABLE_SSID_FLAG,
 						  0, NULL);
 		}
 	}
-- 
2.20.1

[PATCH AUTOSEL 4.4 40/68] powerpc/prom: fix early DEBUG messages

[Sasha Levin]

From: Christophe Leroy <christophe.leroy@c-s.fr>

[ Upstream commit b18f0ae92b0a1db565c3e505fa87b6971ad3b641 ]

This patch fixes early DEBUG messages in prom.c:
- Use %px instead of %p to see the addresses
- Cast memblock_phys_mem_size() with (unsigned long long) to
avoid build failure when phys_addr_t is not 64 bits.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/powerpc/kernel/prom.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/powerpc/kernel/prom.c b/arch/powerpc/kernel/prom.c
index a15fe1d4e84ae..04a27307a2c4d 100644
--- a/arch/powerpc/kernel/prom.c
+++ b/arch/powerpc/kernel/prom.c
@@ -125,7 +125,7 @@ static void __init move_device_tree(void)
 		p = __va(memblock_alloc(size, PAGE_SIZE));
 		memcpy(p, initial_boot_params, size);
 		initial_boot_params = p;
-		DBG("Moved device tree to 0x%p\n", p);
+		DBG("Moved device tree to 0x%px\n", p);
 	}
 
 	DBG("<- move_device_tree\n");
@@ -647,7 +647,7 @@ void __init early_init_devtree(void *params)
 {
 	phys_addr_t limit;
 
-	DBG(" -> early_init_devtree(%p)\n", params);
+	DBG(" -> early_init_devtree(%px)\n", params);
 
 	/* Too early to BUG_ON(), do it by hand */
 	if (!early_init_dt_verify(params))
@@ -707,7 +707,7 @@ void __init early_init_devtree(void *params)
 	memblock_allow_resize();
 	memblock_dump_all();
 
-	DBG("Phys. mem: %llx\n", memblock_phys_mem_size());
+	DBG("Phys. mem: %llx\n", (unsigned long long)memblock_phys_mem_size());
 
 	/* We may need to relocate the flat tree, do it now.
 	 * FIXME .. and the initrd too? */
-- 
2.20.1

[PATCH AUTOSEL 4.4 41/68] powerpc/mm: Make NULL pointer deferences explicit on bad page faults.

[Sasha Levin]

From: Christophe Leroy <christophe.leroy@c-s.fr>

[ Upstream commit 49a502ea23bf9dec47f8f3c3960909ff409cd1bb ]

As several other arches including x86, this patch makes it explicit
that a bad page fault is a NULL pointer dereference when the fault
address is lower than PAGE_SIZE

In the mean time, this page makes all bad_page_fault() messages
shorter so that they remain on one single line. And it prefixes them
by "BUG: " so that they get easily grepped.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Avoid pr_cont()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/powerpc/mm/fault.c | 17 +++++++++--------
 1 file changed, 9 insertions(+), 8 deletions(-)

diff --git a/arch/powerpc/mm/fault.c b/arch/powerpc/mm/fault.c
index d154e333f76b7..d1f860ca03ade 100644
--- a/arch/powerpc/mm/fault.c
+++ b/arch/powerpc/mm/fault.c
@@ -521,21 +521,22 @@ void bad_page_fault(struct pt_regs *regs, unsigned long address, int sig)
 	switch (regs->trap) {
 	case 0x300:
 	case 0x380:
-		printk(KERN_ALERT "Unable to handle kernel paging request for "
-			"data at address 0x%08lx\n", regs->dar);
+		pr_alert("BUG: %s at 0x%08lx\n",
+			 regs->dar < PAGE_SIZE ? "Kernel NULL pointer dereference" :
+			 "Unable to handle kernel data access", regs->dar);
 		break;
 	case 0x400:
 	case 0x480:
-		printk(KERN_ALERT "Unable to handle kernel paging request for "
-			"instruction fetch\n");
+		pr_alert("BUG: Unable to handle kernel instruction fetch%s",
+			 regs->nip < PAGE_SIZE ? " (NULL pointer?)\n" : "\n");
 		break;
 	case 0x600:
-		printk(KERN_ALERT "Unable to handle kernel paging request for "
-			"unaligned access at address 0x%08lx\n", regs->dar);
+		pr_alert("BUG: Unable to handle kernel unaligned access at 0x%08lx\n",
+			 regs->dar);
 		break;
 	default:
-		printk(KERN_ALERT "Unable to handle kernel paging request for "
-			"unknown fault\n");
+		pr_alert("BUG: Unable to handle unknown paging fault at 0x%08lx\n",
+			 regs->dar);
 		break;
 	}
 	printk(KERN_ALERT "Faulting instruction address: 0x%08lx\n",
-- 
2.20.1

[PATCH AUTOSEL 4.4 42/68] powerpc/44x/bamboo: Fix PCI range

[Sasha Levin]

From: Benjamin Herrenschmidt <benh@kernel.crashing.org>

[ Upstream commit 3cfb9ebe906b51f2942b1e251009bb251efd2ba6 ]

The bamboo dts has a bug: it uses a non-naturally aligned range
for PCI memory space. This isnt' supported by the code, thus
causing PCI to break on this system.

This is due to the fact that while the chip memory map has 1G
reserved for PCI memory, it's only 512M aligned. The code doesn't
know how to split that into 2 different PMMs and fails, so limit
the region to 512M.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/powerpc/boot/dts/bamboo.dts | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/arch/powerpc/boot/dts/bamboo.dts b/arch/powerpc/boot/dts/bamboo.dts
index aa68911f6560a..084b82ba74933 100644
--- a/arch/powerpc/boot/dts/bamboo.dts
+++ b/arch/powerpc/boot/dts/bamboo.dts
@@ -268,8 +268,10 @@
 			/* Outbound ranges, one memory and one IO,
 			 * later cannot be changed. Chip supports a second
 			 * IO range but we don't use it for now
+			 * The chip also supports a larger memory range but
+			 * it's not naturally aligned, so our code will break
 			 */
-			ranges = <0x02000000 0x00000000 0xa0000000 0x00000000 0xa0000000 0x00000000 0x40000000
+			ranges = <0x02000000 0x00000000 0xa0000000 0x00000000 0xa0000000 0x00000000 0x20000000
 				  0x02000000 0x00000000 0x00000000 0x00000000 0xe0000000 0x00000000 0x00100000
 				  0x01000000 0x00000000 0x00000000 0x00000000 0xe8000000 0x00000000 0x00010000>;
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 43/68] drbd: reject attach of unsuitable uuids even if connected

[Sasha Levin]

From: Lars Ellenberg <lars.ellenberg@linbit.com>

[ Upstream commit fe43ed97bba3b11521abd934b83ed93143470e4f ]

Multiple failure scenario:
a) all good
   Connected Primary/Secondary UpToDate/UpToDate
b) lose disk on Primary,
   Connected Primary/Secondary Diskless/UpToDate
c) continue to write to the device,
   changes only make it to the Secondary storage.
d) lose disk on Secondary,
   Connected Primary/Secondary Diskless/Diskless
e) now try to re-attach on Primary

This would have succeeded before, even though that is clearly the
wrong data set to attach to (missing the modifications from c).
Because we only compared our "effective" and the "to-be-attached"
data generation uuid tags if (device->state.conn < C_CONNECTED).

Fix: change that constraint to (device->state.pdsk != D_UP_TO_DATE)
compare the uuids, and reject the attach.

This patch also tries to improve the reverse scenario:
first lose Secondary, then Primary disk,
then try to attach the disk on Secondary.

Before this patch, the attach on the Secondary succeeds, but since commit
drbd: disconnect, if the wrong UUIDs are attached on a connected peer
the Primary will notice unsuitable data, and drop the connection hard.

Though unfortunately at a point in time during the handshake where
we cannot easily abort the attach on the peer without more
refactoring of the handshake.

We now reject any attach to "unsuitable" uuids,
as long as we can see a Primary role,
unless we already have access to "good" data.

Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/block/drbd/drbd_nl.c       |  6 +++---
 drivers/block/drbd/drbd_receiver.c | 19 +++++++++++++++++++
 2 files changed, 22 insertions(+), 3 deletions(-)

diff --git a/drivers/block/drbd/drbd_nl.c b/drivers/block/drbd/drbd_nl.c
index 27e1abcf57100..4adbf4c8d532c 100644
--- a/drivers/block/drbd/drbd_nl.c
+++ b/drivers/block/drbd/drbd_nl.c
@@ -1685,9 +1685,9 @@ int drbd_adm_attach(struct sk_buff *skb, struct genl_info *info)
 		}
 	}
 
-	if (device->state.conn < C_CONNECTED &&
-	    device->state.role == R_PRIMARY && device->ed_uuid &&
-	    (device->ed_uuid & ~((u64)1)) != (nbc->md.uuid[UI_CURRENT] & ~((u64)1))) {
+	if (device->state.pdsk != D_UP_TO_DATE && device->ed_uuid &&
+	    (device->state.role == R_PRIMARY || device->state.peer == R_PRIMARY) &&
+            (device->ed_uuid & ~((u64)1)) != (nbc->md.uuid[UI_CURRENT] & ~((u64)1))) {
 		drbd_err(device, "Can only attach to data with current UUID=%016llX\n",
 		    (unsigned long long)device->ed_uuid);
 		retcode = ERR_DATA_NOT_CURRENT;
diff --git a/drivers/block/drbd/drbd_receiver.c b/drivers/block/drbd/drbd_receiver.c
index b1ee358edd3b4..afd8f315d29b1 100644
--- a/drivers/block/drbd/drbd_receiver.c
+++ b/drivers/block/drbd/drbd_receiver.c
@@ -4116,6 +4116,25 @@ static int receive_state(struct drbd_connection *connection, struct packet_info
 	if (peer_state.conn == C_AHEAD)
 		ns.conn = C_BEHIND;
 
+	/* TODO:
+	 * if (primary and diskless and peer uuid != effective uuid)
+	 *     abort attach on peer;
+	 *
+	 * If this node does not have good data, was already connected, but
+	 * the peer did a late attach only now, trying to "negotiate" with me,
+	 * AND I am currently Primary, possibly frozen, with some specific
+	 * "effective" uuid, this should never be reached, really, because
+	 * we first send the uuids, then the current state.
+	 *
+	 * In this scenario, we already dropped the connection hard
+	 * when we received the unsuitable uuids (receive_uuids().
+	 *
+	 * Should we want to change this, that is: not drop the connection in
+	 * receive_uuids() already, then we would need to add a branch here
+	 * that aborts the attach of "unsuitable uuids" on the peer in case
+	 * this node is currently Diskless Primary.
+	 */
+
 	if (device->p_uuid && peer_state.disk >= D_NEGOTIATING &&
 	    get_ldev_if_state(device, D_NEGOTIATING)) {
 		int cr; /* consider resync */
-- 
2.20.1

[PATCH AUTOSEL 4.4 44/68] drbd: fix print_st_err()'s prototype to match the definition

[Sasha Levin]

From: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>

[ Upstream commit 2c38f035117331eb78d0504843c79ea7c7fabf37 ]

print_st_err() is defined with its 4th argument taking an
'enum drbd_state_rv' but its prototype use an int for it.

Fix this by using 'enum drbd_state_rv' in the prototype too.

Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Roland Kammerer <roland.kammerer@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/block/drbd/drbd_state.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/block/drbd/drbd_state.h b/drivers/block/drbd/drbd_state.h
index 7f53c40823cd5..75219cd2534aa 100644
--- a/drivers/block/drbd/drbd_state.h
+++ b/drivers/block/drbd/drbd_state.h
@@ -126,7 +126,7 @@ extern enum drbd_state_rv __drbd_set_state(struct drbd_device *, union drbd_stat
 					   enum chg_state_flags,
 					   struct completion *done);
 extern void print_st_err(struct drbd_device *, union drbd_state,
-			union drbd_state, int);
+			union drbd_state, enum drbd_state_rv);
 
 enum drbd_state_rv
 _conn_request_state(struct drbd_connection *connection, union drbd_state mask, union drbd_state val,
-- 
2.20.1

[PATCH AUTOSEL 4.4 45/68] regulator: tps65910: fix a missing check of return value

[Sasha Levin]

From: Kangjie Lu <kjlu@umn.edu>

[ Upstream commit cd07e3701fa6a4c68f8493ee1d12caa18d46ec6a ]

tps65910_reg_set_bits() may fail. The fix checks if it fails, and if so,
returns with its error code.

Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/regulator/tps65910-regulator.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/regulator/tps65910-regulator.c b/drivers/regulator/tps65910-regulator.c
index 696116ebdf50a..9cde7b0757011 100644
--- a/drivers/regulator/tps65910-regulator.c
+++ b/drivers/regulator/tps65910-regulator.c
@@ -1102,8 +1102,10 @@ static int tps65910_probe(struct platform_device *pdev)
 	platform_set_drvdata(pdev, pmic);
 
 	/* Give control of all register to control port */
-	tps65910_reg_set_bits(pmic->mfd, TPS65910_DEVCTRL,
+	err = tps65910_reg_set_bits(pmic->mfd, TPS65910_DEVCTRL,
 				DEVCTRL_SR_CTL_I2C_SEL_MASK);
+	if (err < 0)
+		return err;
 
 	switch (tps65910_chip_id(tps65910)) {
 	case TPS65910:
-- 
2.20.1

[PATCH AUTOSEL 4.4 46/68] net/net_namespace: Check the return value of register_pernet_subsys()

[Sasha Levin]

From: Aditya Pakki <pakki001@umn.edu>

[ Upstream commit 0eb987c874dc93f9c9d85a6465dbde20fdd3884c ]

In net_ns_init(), register_pernet_subsys() could fail while registering
network namespace subsystems. The fix checks the return value and
sends a panic() on failure.

Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/core/net_namespace.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/net/core/net_namespace.c b/net/core/net_namespace.c
index 087ce1598b746..01bfe28b20a19 100644
--- a/net/core/net_namespace.c
+++ b/net/core/net_namespace.c
@@ -778,7 +778,8 @@ static int __init net_ns_init(void)
 
 	mutex_unlock(&net_mutex);
 
-	register_pernet_subsys(&net_ns_ops);
+	if (register_pernet_subsys(&net_ns_ops))
+		panic("Could not register network namespace subsystems");
 
 	rtnl_register(PF_UNSPEC, RTM_NEWNSID, rtnl_net_newid, NULL, NULL);
 	rtnl_register(PF_UNSPEC, RTM_GETNSID, rtnl_net_getid, rtnl_net_dumpid,
-- 
2.20.1

[PATCH AUTOSEL 4.4 47/68] um: Make GCOV depend on !KCOV

[Sasha Levin]

From: Richard Weinberger <richard@nod.at>

[ Upstream commit 550ed0e2036663b35cec12374b835444f9c60454 ]

Both do more or less the same thing and are mutually exclusive.
If both are enabled the build will fail.
Sooner or later we can kill UML's GCOV.

Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/um/Kconfig.debug | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/um/Kconfig.debug b/arch/um/Kconfig.debug
index 68205fd3b08c8..6ae7f0f434a9c 100644
--- a/arch/um/Kconfig.debug
+++ b/arch/um/Kconfig.debug
@@ -18,6 +18,7 @@ config GPROF
 config GCOV
 	bool "Enable gcov support"
 	depends on DEBUG_INFO
+	depends on !KCOV
 	help
 	  This option allows developers to retrieve coverage data from a UML
 	  session.
-- 
2.20.1

[PATCH AUTOSEL 4.4 48/68] net: stmicro: fix a missing check of clk_prepare

[Sasha Levin]

From: Kangjie Lu <kjlu@umn.edu>

[ Upstream commit f86a3b83833e7cfe558ca4d70b64ebc48903efec ]

clk_prepare() could fail, so let's check its status, and if it fails,
return its error code upstream.

Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-sunxi.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-sunxi.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-sunxi.c
index adff46375a322..6e56c4e5ecec5 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-sunxi.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sunxi.c
@@ -59,7 +59,9 @@ static int sun7i_gmac_init(struct platform_device *pdev, void *priv)
 		gmac->clk_enabled = 1;
 	} else {
 		clk_set_rate(gmac->tx_clk, SUN7I_GMAC_MII_RATE);
-		clk_prepare(gmac->tx_clk);
+		ret = clk_prepare(gmac->tx_clk);
+		if (ret)
+			return ret;
 	}
 
 	return 0;
-- 
2.20.1

[PATCH AUTOSEL 4.4 49/68] atl1e: checking the status of atl1e_write_phy_reg

[Sasha Levin]

From: Kangjie Lu <kjlu@umn.edu>

[ Upstream commit ff07d48d7bc0974d4f96a85a4df14564fb09f1ef ]

atl1e_write_phy_reg() could fail. The fix issues an error message when
it fails.

Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/atheros/atl1e/atl1e_main.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/atheros/atl1e/atl1e_main.c b/drivers/net/ethernet/atheros/atl1e/atl1e_main.c
index 59a03a193e835..4384b2b4d2382 100644
--- a/drivers/net/ethernet/atheros/atl1e/atl1e_main.c
+++ b/drivers/net/ethernet/atheros/atl1e/atl1e_main.c
@@ -478,7 +478,9 @@ static void atl1e_mdio_write(struct net_device *netdev, int phy_id,
 {
 	struct atl1e_adapter *adapter = netdev_priv(netdev);
 
-	atl1e_write_phy_reg(&adapter->hw, reg_num & MDIO_REG_ADDR_MASK, val);
+	if (atl1e_write_phy_reg(&adapter->hw,
+				reg_num & MDIO_REG_ADDR_MASK, val))
+		netdev_err(netdev, "write phy register failed\n");
 }
 
 static int atl1e_mii_ioctl(struct net_device *netdev,
-- 
2.20.1

[PATCH AUTOSEL 4.4 50/68] tipc: fix a missing check of genlmsg_put

[Sasha Levin]

From: Kangjie Lu <kjlu@umn.edu>

[ Upstream commit 46273cf7e009231d2b6bc10a926e82b8928a9fb2 ]

genlmsg_put could fail. The fix inserts a check of its return value, and
if it fails, returns -EMSGSIZE.

Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/tipc/netlink_compat.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/net/tipc/netlink_compat.c b/net/tipc/netlink_compat.c
index d2bf92e711505..4f6fbd2f29add 100644
--- a/net/tipc/netlink_compat.c
+++ b/net/tipc/netlink_compat.c
@@ -926,6 +926,8 @@ static int tipc_nl_compat_publ_dump(struct tipc_nl_compat_msg *msg, u32 sock)
 
 	hdr = genlmsg_put(args, 0, 0, &tipc_genl_family, NLM_F_MULTI,
 			  TIPC_NL_PUBL_GET);
+	if (!hdr)
+		return -EMSGSIZE;
 
 	nest = nla_nest_start(args, TIPC_NLA_SOCK);
 	if (!nest) {
-- 
2.20.1

[PATCH AUTOSEL 4.4 51/68] ocfs2: clear journal dirty flag after shutdown journal

[Sasha Levin]

From: Junxiao Bi <junxiao.bi@oracle.com>

[ Upstream commit d85400af790dba2aa294f0a77e712f166681f977 ]

Dirty flag of the journal should be cleared at the last stage of umount,
if do it before jbd2_journal_destroy(), then some metadata in uncommitted
transaction could be lost due to io error, but as dirty flag of journal
was already cleared, we can't find that until run a full fsck.  This may
cause system panic or other corruption.

Link: http://lkml.kernel.org/r/20181121020023.3034-3-junxiao.bi@oracle.com
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Yiwen Jiang <jiangyiwen@huawei.com>
Reviewed-by: Joseph Qi <jiangqi903@gmail.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: Changwei Ge <ge.changwei@h3c.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@versity.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 fs/ocfs2/journal.c | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/fs/ocfs2/journal.c b/fs/ocfs2/journal.c
index 722eb5bc9b8f0..2301011428a1d 100644
--- a/fs/ocfs2/journal.c
+++ b/fs/ocfs2/journal.c
@@ -1017,7 +1017,8 @@ void ocfs2_journal_shutdown(struct ocfs2_super *osb)
 			mlog_errno(status);
 	}
 
-	if (status == 0) {
+	/* Shutdown the kernel journal system */
+	if (!jbd2_journal_destroy(journal->j_journal) && !status) {
 		/*
 		 * Do not toggle if flush was unsuccessful otherwise
 		 * will leave dirty metadata in a "clean" journal
@@ -1026,9 +1027,6 @@ void ocfs2_journal_shutdown(struct ocfs2_super *osb)
 		if (status < 0)
 			mlog_errno(status);
 	}
-
-	/* Shutdown the kernel journal system */
-	jbd2_journal_destroy(journal->j_journal);
 	journal->j_journal = NULL;
 
 	OCFS2_I(inode)->ip_open_count--;
-- 
2.20.1

[PATCH AUTOSEL 4.4 52/68] lib/genalloc.c: use vzalloc_node() to allocate the bitmap

[Sasha Levin]

From: Huang Shijie <sjhuang@iluvatar.ai>

[ Upstream commit 6862d2fc81859f88c1f3f660886427893f2b4f3f ]

Some devices may have big memory on chip, such as over 1G.  In some
cases, the nbytes maybe bigger then 4M which is the bounday of the
memory buddy system (4K default).

So use vzalloc_node() to allocate the bitmap.  Also use vfree to free
it.

Link: http://lkml.kernel.org/r/20181225015701.6289-1-sjhuang@iluvatar.ai
Signed-off-by: Huang Shijie <sjhuang@iluvatar.ai>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexey Skidanov <alexey.skidanov@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 lib/genalloc.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/lib/genalloc.c b/lib/genalloc.c
index e4303fb2a7b28..38764572ddde8 100644
--- a/lib/genalloc.c
+++ b/lib/genalloc.c
@@ -187,7 +187,7 @@ int gen_pool_add_virt(struct gen_pool *pool, unsigned long virt, phys_addr_t phy
 	int nbytes = sizeof(struct gen_pool_chunk) +
 				BITS_TO_LONGS(nbits) * sizeof(long);
 
-	chunk = kzalloc_node(nbytes, GFP_KERNEL, nid);
+	chunk = vzalloc_node(nbytes, nid);
 	if (unlikely(chunk == NULL))
 		return -ENOMEM;
 
@@ -251,7 +251,7 @@ void gen_pool_destroy(struct gen_pool *pool)
 		bit = find_next_bit(chunk->bits, end_bit, 0);
 		BUG_ON(bit < end_bit);
 
-		kfree(chunk);
+		vfree(chunk);
 	}
 	kfree_const(pool->name);
 	kfree(pool);
-- 
2.20.1

[PATCH AUTOSEL 4.4 53/68] lib/genalloc.c: include vmalloc.h

[Sasha Levin]

From: Olof Johansson <olof@lixom.net>

[ Upstream commit 35004f2e55807a1a1491db24ab512dd2f770a130 ]

Fixes build break on most ARM/ARM64 defconfigs:

  lib/genalloc.c: In function 'gen_pool_add_virt':
  lib/genalloc.c:190:10: error: implicit declaration of function 'vzalloc_node'; did you mean 'kzalloc_node'?
  lib/genalloc.c:190:8: warning: assignment to 'struct gen_pool_chunk *' from 'int' makes pointer from integer without a cast [-Wint-conversion]
  lib/genalloc.c: In function 'gen_pool_destroy':
  lib/genalloc.c:254:3: error: implicit declaration of function 'vfree'; did you mean 'kfree'?

Fixes: 6862d2fc8185 ('lib/genalloc.c: use vzalloc_node() to allocate the bitmap')
Cc: Huang Shijie <sjhuang@iluvatar.ai>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexey Skidanov <alexey.skidanov@intel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 lib/genalloc.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/lib/genalloc.c b/lib/genalloc.c
index 38764572ddde8..e3a475b14e260 100644
--- a/lib/genalloc.c
+++ b/lib/genalloc.c
@@ -35,6 +35,7 @@
 #include <linux/interrupt.h>
 #include <linux/genalloc.h>
 #include <linux/of_device.h>
+#include <linux/vmalloc.h>
 
 static inline size_t chunk_size(const struct gen_pool_chunk *chunk)
 {
-- 
2.20.1

[PATCH AUTOSEL 4.4 54/68] mtd: Check add_mtd_device() ret code

[Sasha Levin]

From: Boris Brezillon <bbrezillon@kernel.org>

[ Upstream commit 2b6f0090a3335b7bdd03ca520c35591159463041 ]

add_mtd_device() can fail. We should always check its return value
and gracefully handle the failure case. Fix the call sites where this
not done (in mtdpart.c) and add a __must_check attribute to the
prototype to avoid this kind of mistakes.

Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/mtd/mtdcore.h |  2 +-
 drivers/mtd/mtdpart.c | 36 +++++++++++++++++++++++++++++++-----
 2 files changed, 32 insertions(+), 6 deletions(-)

diff --git a/drivers/mtd/mtdcore.h b/drivers/mtd/mtdcore.h
index 7b0353399a106..b837f44716820 100644
--- a/drivers/mtd/mtdcore.h
+++ b/drivers/mtd/mtdcore.h
@@ -6,7 +6,7 @@
 extern struct mutex mtd_table_mutex;
 
 struct mtd_info *__mtd_next_device(int i);
-int add_mtd_device(struct mtd_info *mtd);
+int __must_check add_mtd_device(struct mtd_info *mtd);
 int del_mtd_device(struct mtd_info *mtd);
 int add_mtd_partitions(struct mtd_info *, const struct mtd_partition *, int);
 int del_mtd_partitions(struct mtd_info *);
diff --git a/drivers/mtd/mtdpart.c b/drivers/mtd/mtdpart.c
index f8ba153f63bfe..9b48be05cd1af 100644
--- a/drivers/mtd/mtdpart.c
+++ b/drivers/mtd/mtdpart.c
@@ -610,10 +610,22 @@ int mtd_add_partition(struct mtd_info *master, const char *name,
 	list_add(&new->list, &mtd_partitions);
 	mutex_unlock(&mtd_partitions_mutex);
 
-	add_mtd_device(&new->mtd);
+	ret = add_mtd_device(&new->mtd);
+	if (ret)
+		goto err_remove_part;
 
 	mtd_add_partition_attrs(new);
 
+	return 0;
+
+err_remove_part:
+	mutex_lock(&mtd_partitions_mutex);
+	list_del(&new->list);
+	mutex_unlock(&mtd_partitions_mutex);
+
+	free_partition(new);
+	pr_info("%s:%i\n", __func__, __LINE__);
+
 	return ret;
 }
 EXPORT_SYMBOL_GPL(mtd_add_partition);
@@ -658,28 +670,42 @@ int add_mtd_partitions(struct mtd_info *master,
 {
 	struct mtd_part *slave;
 	uint64_t cur_offset = 0;
-	int i;
+	int i, ret;
 
 	printk(KERN_NOTICE "Creating %d MTD partitions on \"%s\":\n", nbparts, master->name);
 
 	for (i = 0; i < nbparts; i++) {
 		slave = allocate_partition(master, parts + i, i, cur_offset);
 		if (IS_ERR(slave)) {
-			del_mtd_partitions(master);
-			return PTR_ERR(slave);
+			ret = PTR_ERR(slave);
+			goto err_del_partitions;
 		}
 
 		mutex_lock(&mtd_partitions_mutex);
 		list_add(&slave->list, &mtd_partitions);
 		mutex_unlock(&mtd_partitions_mutex);
 
-		add_mtd_device(&slave->mtd);
+		ret = add_mtd_device(&slave->mtd);
+		if (ret) {
+			mutex_lock(&mtd_partitions_mutex);
+			list_del(&slave->list);
+			mutex_unlock(&mtd_partitions_mutex);
+
+			free_partition(slave);
+			goto err_del_partitions;
+		}
+
 		mtd_add_partition_attrs(slave);
 
 		cur_offset = slave->offset + slave->mtd.size;
 	}
 
 	return 0;
+
+err_del_partitions:
+	del_mtd_partitions(master);
+
+	return ret;
 }
 
 static DEFINE_SPINLOCK(part_parser_lock);
-- 
2.20.1

[PATCH AUTOSEL 4.4 55/68] tipc: fix memory leak in tipc_nl_compat_publ_dump

[Sasha Levin]

From: "Gustavo A. R. Silva" <gustavo@embeddedor.com>

[ Upstream commit f87d8ad9233f115db92c6c087d58403b0009ed36 ]

There is a memory leak in case genlmsg_put fails.

Fix this by freeing *args* before return.

Addresses-Coverity-ID: 1476406 ("Resource leak")
Fixes: 46273cf7e009 ("tipc: fix a missing check of genlmsg_put")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/tipc/netlink_compat.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/net/tipc/netlink_compat.c b/net/tipc/netlink_compat.c
index 4f6fbd2f29add..392d72d65e602 100644
--- a/net/tipc/netlink_compat.c
+++ b/net/tipc/netlink_compat.c
@@ -926,8 +926,10 @@ static int tipc_nl_compat_publ_dump(struct tipc_nl_compat_msg *msg, u32 sock)
 
 	hdr = genlmsg_put(args, 0, 0, &tipc_genl_family, NLM_F_MULTI,
 			  TIPC_NL_PUBL_GET);
-	if (!hdr)
+	if (!hdr) {
+		kfree_skb(args);
 		return -EMSGSIZE;
+	}
 
 	nest = nla_nest_start(args, TIPC_NLA_SOCK);
 	if (!nest) {
-- 
2.20.1

[PATCH AUTOSEL 4.4 56/68] net/core/neighbour: tell kmemleak about hash tables

[Sasha Levin]

From: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>

[ Upstream commit 85704cb8dcfd88d351bfc87faaeba1c8214f3177 ]

This fixes false-positive kmemleak reports about leaked neighbour entries:

unreferenced object 0xffff8885c6e4d0a8 (size 1024):
  comm "softirq", pid 0, jiffies 4294922664 (age 167640.804s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 20 2c f3 83 ff ff ff ff  ........ ,......
    08 c0 ef 5f 84 88 ff ff 01 8c 7d 02 01 00 00 00  ..._......}.....
  backtrace:
    [<00000000748509fe>] ip6_finish_output2+0x887/0x1e40
    [<0000000036d7a0d8>] ip6_output+0x1ba/0x600
    [<0000000027ea7dba>] ip6_send_skb+0x92/0x2f0
    [<00000000d6e2111d>] udp_v6_send_skb.isra.24+0x680/0x15e0
    [<000000000668a8be>] udpv6_sendmsg+0x18c9/0x27a0
    [<000000004bd5fa90>] sock_sendmsg+0xb3/0xf0
    [<000000008227b29f>] ___sys_sendmsg+0x745/0x8f0
    [<000000008698009d>] __sys_sendmsg+0xde/0x170
    [<00000000889dacf1>] do_syscall_64+0x9b/0x400
    [<0000000081cdb353>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
    [<000000005767ed39>] 0xffffffffffffffff

Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/core/neighbour.c | 13 +++++++++----
 1 file changed, 9 insertions(+), 4 deletions(-)

diff --git a/net/core/neighbour.c b/net/core/neighbour.c
index b3b242f7ecfd2..bba672482a0ef 100644
--- a/net/core/neighbour.c
+++ b/net/core/neighbour.c
@@ -18,6 +18,7 @@
 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
 
 #include <linux/slab.h>
+#include <linux/kmemleak.h>
 #include <linux/types.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
@@ -325,12 +326,14 @@ static struct neigh_hash_table *neigh_hash_alloc(unsigned int shift)
 	ret = kmalloc(sizeof(*ret), GFP_ATOMIC);
 	if (!ret)
 		return NULL;
-	if (size <= PAGE_SIZE)
+	if (size <= PAGE_SIZE) {
 		buckets = kzalloc(size, GFP_ATOMIC);
-	else
+	} else {
 		buckets = (struct neighbour __rcu **)
 			  __get_free_pages(GFP_ATOMIC | __GFP_ZERO,
 					   get_order(size));
+		kmemleak_alloc(buckets, size, 0, GFP_ATOMIC);
+	}
 	if (!buckets) {
 		kfree(ret);
 		return NULL;
@@ -350,10 +353,12 @@ static void neigh_hash_free_rcu(struct rcu_head *head)
 	size_t size = (1 << nht->hash_shift) * sizeof(struct neighbour *);
 	struct neighbour __rcu **buckets = nht->hash_buckets;
 
-	if (size <= PAGE_SIZE)
+	if (size <= PAGE_SIZE) {
 		kfree(buckets);
-	else
+	} else {
+		kmemleak_free(buckets);
 		free_pages((unsigned long)buckets, get_order(size));
+	}
 	kfree(nht);
 }
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 57/68] net/core/neighbour: fix kmemleak minimal reference count for hash tables

[Sasha Levin]

From: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>

[ Upstream commit 01b833ab44c9e484060aad72267fc7e71beb559b ]

This should be 1 for normal allocations, 0 disables leak reporting.

Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Fixes: 85704cb8dcfd ("net/core/neighbour: tell kmemleak about hash tables")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/core/neighbour.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/net/core/neighbour.c b/net/core/neighbour.c
index bba672482a0ef..8aef689b8f32d 100644
--- a/net/core/neighbour.c
+++ b/net/core/neighbour.c
@@ -332,7 +332,7 @@ static struct neigh_hash_table *neigh_hash_alloc(unsigned int shift)
 		buckets = (struct neighbour __rcu **)
 			  __get_free_pages(GFP_ATOMIC | __GFP_ZERO,
 					   get_order(size));
-		kmemleak_alloc(buckets, size, 0, GFP_ATOMIC);
+		kmemleak_alloc(buckets, size, 1, GFP_ATOMIC);
 	}
 	if (!buckets) {
 		kfree(ret);
-- 
2.20.1

[PATCH AUTOSEL 4.4 58/68] sfc: suppress duplicate nvmem partition types in efx_ef10_mtd_probe

[Sasha Levin]

From: Edward Cree <ecree@solarflare.com>

[ Upstream commit 3366463513f544c12c6b88c13da4462ee9e7a1a1 ]

Use a bitmap to keep track of which partition types we've already seen;
 for duplicates, return -EEXIST from efx_ef10_mtd_probe_partition() and
 thus skip adding that partition.
Duplicate partitions occur because of the A/B backup scheme used by newer
 sfc NICs.  Prior to this patch they cause sysfs_warn_dup errors because
 they have the same name, causing us not to expose any MTDs at all.

Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/sfc/ef10.c | 29 +++++++++++++++++++++--------
 1 file changed, 21 insertions(+), 8 deletions(-)

diff --git a/drivers/net/ethernet/sfc/ef10.c b/drivers/net/ethernet/sfc/ef10.c
index 063aca17e698b..79a1031c3ef77 100644
--- a/drivers/net/ethernet/sfc/ef10.c
+++ b/drivers/net/ethernet/sfc/ef10.c
@@ -4433,22 +4433,25 @@ static const struct efx_ef10_nvram_type_info efx_ef10_nvram_types[] = {
 	{ NVRAM_PARTITION_TYPE_LICENSE,		   0,    0, "sfc_license" },
 	{ NVRAM_PARTITION_TYPE_PHY_MIN,		   0xff, 0, "sfc_phy_fw" },
 };
+#define EF10_NVRAM_PARTITION_COUNT	ARRAY_SIZE(efx_ef10_nvram_types)
 
 static int efx_ef10_mtd_probe_partition(struct efx_nic *efx,
 					struct efx_mcdi_mtd_partition *part,
-					unsigned int type)
+					unsigned int type,
+					unsigned long *found)
 {
 	MCDI_DECLARE_BUF(inbuf, MC_CMD_NVRAM_METADATA_IN_LEN);
 	MCDI_DECLARE_BUF(outbuf, MC_CMD_NVRAM_METADATA_OUT_LENMAX);
 	const struct efx_ef10_nvram_type_info *info;
 	size_t size, erase_size, outlen;
+	int type_idx = 0;
 	bool protected;
 	int rc;
 
-	for (info = efx_ef10_nvram_types; ; info++) {
-		if (info ==
-		    efx_ef10_nvram_types + ARRAY_SIZE(efx_ef10_nvram_types))
+	for (type_idx = 0; ; type_idx++) {
+		if (type_idx == EF10_NVRAM_PARTITION_COUNT)
 			return -ENODEV;
+		info = efx_ef10_nvram_types + type_idx;
 		if ((type & ~info->type_mask) == info->type)
 			break;
 	}
@@ -4461,6 +4464,13 @@ static int efx_ef10_mtd_probe_partition(struct efx_nic *efx,
 	if (protected)
 		return -ENODEV; /* hide it */
 
+	/* If we've already exposed a partition of this type, hide this
+	 * duplicate.  All operations on MTDs are keyed by the type anyway,
+	 * so we can't act on the duplicate.
+	 */
+	if (__test_and_set_bit(type_idx, found))
+		return -EEXIST;
+
 	part->nvram_type = type;
 
 	MCDI_SET_DWORD(inbuf, NVRAM_METADATA_IN_TYPE, type);
@@ -4489,6 +4499,7 @@ static int efx_ef10_mtd_probe_partition(struct efx_nic *efx,
 static int efx_ef10_mtd_probe(struct efx_nic *efx)
 {
 	MCDI_DECLARE_BUF(outbuf, MC_CMD_NVRAM_PARTITIONS_OUT_LENMAX);
+	DECLARE_BITMAP(found, EF10_NVRAM_PARTITION_COUNT);
 	struct efx_mcdi_mtd_partition *parts;
 	size_t outlen, n_parts_total, i, n_parts;
 	unsigned int type;
@@ -4517,11 +4528,13 @@ static int efx_ef10_mtd_probe(struct efx_nic *efx)
 	for (i = 0; i < n_parts_total; i++) {
 		type = MCDI_ARRAY_DWORD(outbuf, NVRAM_PARTITIONS_OUT_TYPE_ID,
 					i);
-		rc = efx_ef10_mtd_probe_partition(efx, &parts[n_parts], type);
-		if (rc == 0)
-			n_parts++;
-		else if (rc != -ENODEV)
+		rc = efx_ef10_mtd_probe_partition(efx, &parts[n_parts], type,
+						  found);
+		if (rc == -EEXIST || rc == -ENODEV)
+			continue;
+		if (rc)
 			goto fail;
+		n_parts++;
 	}
 
 	rc = efx_mtd_add(efx, &parts[0].common, n_parts, sizeof(*parts));
-- 
2.20.1

[PATCH AUTOSEL 4.4 59/68] decnet: fix DN_IFREQ_SIZE

[Sasha Levin]

From: Johannes Berg <johannes.berg@intel.com>

[ Upstream commit 50c2936634bcb1db78a8ca63249236810c11a80f ]

Digging through the ioctls with Al because of the previous
patches, we found that on 64-bit decnet's dn_dev_ioctl()
is wrong, because struct ifreq::ifr_ifru is actually 24
bytes (not 16 as expected from struct sockaddr) due to the
ifru_map and ifru_settings members.

Clearly, decnet expects the ioctl to be called with a struct
like
  struct ifreq_dn {
    char ifr_name[IFNAMSIZ];
    struct sockaddr_dn ifr_addr;
  };

since it does
  struct ifreq *ifr = ...;
  struct sockaddr_dn *sdn = (struct sockaddr_dn *)&ifr->ifr_addr;

This means that DN_IFREQ_SIZE is too big for what it wants on
64-bit, as it is
  sizeof(struct ifreq) - sizeof(struct sockaddr) +
  sizeof(struct sockaddr_dn)

This assumes that sizeof(struct sockaddr) is the size of ifr_ifru
but that isn't true.

Fix this to use offsetof(struct ifreq, ifr_ifru).

This indeed doesn't really matter much - the result is that we
copy in/out 8 bytes more than we should on 64-bit platforms. In
case the "struct ifreq_dn" lands just on the end of a page though
it might lead to faults.

As far as I can tell, it has been like this forever, so it seems
very likely that nobody cares.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/decnet/dn_dev.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/net/decnet/dn_dev.c b/net/decnet/dn_dev.c
index b2c26b081134a..80554e7e9a0f6 100644
--- a/net/decnet/dn_dev.c
+++ b/net/decnet/dn_dev.c
@@ -55,7 +55,7 @@
 #include <net/dn_neigh.h>
 #include <net/dn_fib.h>
 
-#define DN_IFREQ_SIZE (sizeof(struct ifreq) - sizeof(struct sockaddr) + sizeof(struct sockaddr_dn))
+#define DN_IFREQ_SIZE (offsetof(struct ifreq, ifr_ifru) + sizeof(struct sockaddr_dn))
 
 static char dn_rt_all_end_mcast[ETH_ALEN] = {0xAB,0x00,0x00,0x04,0x00,0x00};
 static char dn_rt_all_rt_mcast[ETH_ALEN]  = {0xAB,0x00,0x00,0x03,0x00,0x00};
-- 
2.20.1

[PATCH AUTOSEL 4.4 60/68] tipc: fix skb may be leaky in tipc_link_input

[Sasha Levin]

From: Hoang Le <hoang.h.le@dektech.com.au>

[ Upstream commit 7384b538d3aed2ed49d3575483d17aeee790fb06 ]

When we free skb at tipc_data_input, we return a 'false' boolean.
Then, skb passed to subcalling tipc_link_input in tipc_link_rcv,

<snip>
1303 int tipc_link_rcv:
...
1354    if (!tipc_data_input(l, skb, l->inputq))
1355        rc |= tipc_link_input(l, skb, l->inputq);
</snip>

Fix it by simple changing to a 'true' boolean when skb is being free-ed.
Then, tipc_link_rcv will bypassed to subcalling tipc_link_input as above
condition.

Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <maloy@donjonn.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/tipc/link.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/net/tipc/link.c b/net/tipc/link.c
index 736fffb28ab6f..0080699b7cd1b 100644
--- a/net/tipc/link.c
+++ b/net/tipc/link.c
@@ -883,7 +883,7 @@ static bool tipc_data_input(struct tipc_link *l, struct sk_buff *skb,
 	default:
 		pr_warn("Dropping received illegal msg type\n");
 		kfree_skb(skb);
-		return false;
+		return true;
 	};
 }
 
-- 
2.20.1

[PATCH AUTOSEL 4.4 61/68] sfc: initialise found bitmap in efx_ef10_mtd_probe

[Sasha Levin]

From: Bert Kenward <bkenward@solarflare.com>

[ Upstream commit c65285428b6e7797f1bb063f33b0ae7e93397b7b ]

The bitmap of found partitions in efx_ef10_mtd_probe was not
initialised, causing partitions to be suppressed based off whatever
value was in the bitmap at the start.

Fixes: 3366463513f5 ("sfc: suppress duplicate nvmem partition types in efx_ef10_mtd_probe")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/sfc/ef10.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/sfc/ef10.c b/drivers/net/ethernet/sfc/ef10.c
index 79a1031c3ef77..6dcd436e6e323 100644
--- a/drivers/net/ethernet/sfc/ef10.c
+++ b/drivers/net/ethernet/sfc/ef10.c
@@ -4499,7 +4499,7 @@ static int efx_ef10_mtd_probe_partition(struct efx_nic *efx,
 static int efx_ef10_mtd_probe(struct efx_nic *efx)
 {
 	MCDI_DECLARE_BUF(outbuf, MC_CMD_NVRAM_PARTITIONS_OUT_LENMAX);
-	DECLARE_BITMAP(found, EF10_NVRAM_PARTITION_COUNT);
+	DECLARE_BITMAP(found, EF10_NVRAM_PARTITION_COUNT) = { 0 };
 	struct efx_mcdi_mtd_partition *parts;
 	size_t outlen, n_parts_total, i, n_parts;
 	unsigned int type;
-- 
2.20.1

[PATCH AUTOSEL 4.4 62/68] net: fix possible overflow in __sk_mem_raise_allocated()

[Sasha Levin]

From: Eric Dumazet <edumazet@google.com>

[ Upstream commit 5bf325a53202b8728cf7013b72688c46071e212e ]

With many active TCP sockets, fat TCP sockets could fool
__sk_mem_raise_allocated() thanks to an overflow.

They would increase their share of the memory, instead
of decreasing it.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 include/net/sock.h | 2 +-
 net/core/sock.c    | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/include/net/sock.h b/include/net/sock.h
index 5ed4786a2058b..de4434284a34b 100644
--- a/include/net/sock.h
+++ b/include/net/sock.h
@@ -1282,7 +1282,7 @@ static inline void sk_sockets_allocated_inc(struct sock *sk)
 	percpu_counter_inc(prot->sockets_allocated);
 }
 
-static inline int
+static inline u64
 sk_sockets_allocated_read_positive(struct sock *sk)
 {
 	struct proto *prot = sk->sk_prot;
diff --git a/net/core/sock.c b/net/core/sock.c
index 8aa4a5f895723..0f4c15fcd87d3 100644
--- a/net/core/sock.c
+++ b/net/core/sock.c
@@ -2122,7 +2122,7 @@ int __sk_mem_schedule(struct sock *sk, int size, int kind)
 	}
 
 	if (sk_has_memory_pressure(sk)) {
-		int alloc;
+		u64 alloc;
 
 		if (!sk_under_memory_pressure(sk))
 			return 1;
-- 
2.20.1

[PATCH AUTOSEL 4.4 63/68] net: dev: Use unsigned integer as an argument to left-shift

[Sasha Levin]

From: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

[ Upstream commit f4d7b3e23d259c44f1f1c39645450680fcd935d6 ]

1 << 31 is Undefined Behaviour according to the C standard.
Use U type modifier to avoid theoretical overflow.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 include/linux/netdevice.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/include/linux/netdevice.h b/include/linux/netdevice.h
index 0b211d482c961..861b71377e5e1 100644
--- a/include/linux/netdevice.h
+++ b/include/linux/netdevice.h
@@ -3298,7 +3298,7 @@ static inline u32 netif_msg_init(int debug_value, int default_msg_enable_bits)
 	if (debug_value == 0)	/* no output */
 		return 0;
 	/* set low N bits */
-	return (1 << debug_value) - 1;
+	return (1U << debug_value) - 1;
 }
 
 static inline void __netif_tx_lock(struct netdev_queue *txq, int cpu)
-- 
2.20.1

[PATCH AUTOSEL 4.4 64/68] scsi: libsas: Support SATA PHY connection rate unmatch fixing during discovery

[Sasha Levin]

From: John Garry <john.garry@huawei.com>

[ Upstream commit cec9771d2e954650095aa37a6a97722c8194e7d2 ]

   +----------+             +----------+
   |          |             |          |
   |          |--- 3.0 G ---|          |--- 6.0 G --- SAS  disk
   |          |             |          |
   |          |--- 3.0 G ---|          |--- 6.0 G --- SAS  disk
   |initiator |             |          |
   | device   |--- 3.0 G ---| Expander |--- 6.0 G --- SAS  disk
   |          |             |          |
   |          |--- 3.0 G ---|          |--- 6.0 G --- SATA disk  -->failed to connect
   |          |             |          |
   |          |             |          |--- 6.0 G --- SATA disk  -->failed to connect
   |          |             |          |
   +----------+             +----------+

According to Serial Attached SCSI - 1.1 (SAS-1.1):
If an expander PHY attached to a SATA PHY is using a physical link rate
greater than the maximum connection rate supported by the pathway from an
STP initiator port, a management application client should use the SMP PHY
CONTROL function (see 10.4.3.10) to set the PROGRAMMED MAXIMUM PHYSICAL
LINK RATE field of the expander PHY to the maximum connection rate
supported by the pathway from that STP initiator port.

Currently libsas does not support checking if this condition occurs, nor
rectifying when it does.

Such a condition is not at all common, however it has been seen on some
pre-silicon environments where the initiator PHY only supports a 1.5 Gbit
maximum linkrate, mated with 12G expander PHYs and 3/6G SATA phy.

This patch adds support for checking and rectifying this condition during
initial device discovery only.

We do support checking min pathway connection rate during revalidation phase,
when new devices can be detected in the topology. However we do not
support in the case of the the user reprogramming PHY linkrates, such that
min pathway condition is not met/maintained.

A note on root port PHY rates:
The libsas root port PHY rates calculation is broken. Libsas sets the
rates (min, max, and current linkrate) of a root port to the same linkrate
of the first PHY member of that same port. In doing so, it assumes that
all other PHYs which subsequently join the port to have the same
negotiated linkrate, when they could actually be different.

In practice this doesn't happen, as initiator and expander PHYs are
normally initialised with consistent min/max linkrates.

This has not caused an issue so far, so leave alone for now.

Tested-by: Jian Luo <luojian5@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/libsas/sas_expander.c | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/drivers/scsi/libsas/sas_expander.c b/drivers/scsi/libsas/sas_expander.c
index 400eee9d77832..ba16231665a5e 100644
--- a/drivers/scsi/libsas/sas_expander.c
+++ b/drivers/scsi/libsas/sas_expander.c
@@ -806,6 +806,26 @@ static struct domain_device *sas_ex_discover_end_dev(
 
 #ifdef CONFIG_SCSI_SAS_ATA
 	if ((phy->attached_tproto & SAS_PROTOCOL_STP) || phy->attached_sata_dev) {
+		if (child->linkrate > parent->min_linkrate) {
+			struct sas_phy_linkrates rates = {
+				.maximum_linkrate = parent->min_linkrate,
+				.minimum_linkrate = parent->min_linkrate,
+			};
+			int ret;
+
+			pr_notice("ex %016llx phy%02d SATA device linkrate > min pathway connection rate, attempting to lower device linkrate\n",
+				   SAS_ADDR(child->sas_addr), phy_id);
+			ret = sas_smp_phy_control(parent, phy_id,
+						  PHY_FUNC_LINK_RESET, &rates);
+			if (ret) {
+				pr_err("ex %016llx phy%02d SATA device could not set linkrate (%d)\n",
+				       SAS_ADDR(child->sas_addr), phy_id, ret);
+				goto out_free;
+			}
+			pr_notice("ex %016llx phy%02d SATA device set linkrate successfully\n",
+				  SAS_ADDR(child->sas_addr), phy_id);
+			child->linkrate = child->min_linkrate;
+		}
 		res = sas_get_ata_info(child, phy);
 		if (res)
 			goto out_free;
-- 
2.20.1

[PATCH AUTOSEL 4.4 65/68] ACPI / APEI: Switch estatus pool to use vmalloc memory

[Sasha Levin]

From: James Morse <james.morse@arm.com>

[ Upstream commit 0ac234be1a9497498e57d958f4251f5257b116b4 ]

The ghes code is careful to parse and round firmware's advertised
memory requirements for CPER records, up to a maximum of 64K.
However when ghes_estatus_pool_expand() does its work, it splits
the requested size into PAGE_SIZE granules.

This means if firmware generates 5K of CPER records, and correctly
describes this in the table, __process_error() will silently fail as it
is unable to allocate more than PAGE_SIZE.

Switch the estatus pool to vmalloc() memory. On x86 vmalloc() memory
may fault and be fixed up by vmalloc_fault(). To prevent this call
vmalloc_sync_all() before an NMI handler could discover the memory.

Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/acpi/apei/ghes.c | 30 +++++++++++++++---------------
 1 file changed, 15 insertions(+), 15 deletions(-)

diff --git a/drivers/acpi/apei/ghes.c b/drivers/acpi/apei/ghes.c
index bb81cd05f0bc8..d532aa87eef10 100644
--- a/drivers/acpi/apei/ghes.c
+++ b/drivers/acpi/apei/ghes.c
@@ -198,40 +198,40 @@ static int ghes_estatus_pool_init(void)
 	return 0;
 }
 
-static void ghes_estatus_pool_free_chunk_page(struct gen_pool *pool,
+static void ghes_estatus_pool_free_chunk(struct gen_pool *pool,
 					      struct gen_pool_chunk *chunk,
 					      void *data)
 {
-	free_page(chunk->start_addr);
+	vfree((void *)chunk->start_addr);
 }
 
 static void ghes_estatus_pool_exit(void)
 {
 	gen_pool_for_each_chunk(ghes_estatus_pool,
-				ghes_estatus_pool_free_chunk_page, NULL);
+				ghes_estatus_pool_free_chunk, NULL);
 	gen_pool_destroy(ghes_estatus_pool);
 }
 
 static int ghes_estatus_pool_expand(unsigned long len)
 {
-	unsigned long i, pages, size, addr;
-	int ret;
+	unsigned long size, addr;
 
 	ghes_estatus_pool_size_request += PAGE_ALIGN(len);
 	size = gen_pool_size(ghes_estatus_pool);
 	if (size >= ghes_estatus_pool_size_request)
 		return 0;
-	pages = (ghes_estatus_pool_size_request - size) / PAGE_SIZE;
-	for (i = 0; i < pages; i++) {
-		addr = __get_free_page(GFP_KERNEL);
-		if (!addr)
-			return -ENOMEM;
-		ret = gen_pool_add(ghes_estatus_pool, addr, PAGE_SIZE, -1);
-		if (ret)
-			return ret;
-	}
 
-	return 0;
+	addr = (unsigned long)vmalloc(PAGE_ALIGN(len));
+	if (!addr)
+		return -ENOMEM;
+
+	/*
+	 * New allocation must be visible in all pgd before it can be found by
+	 * an NMI allocating from the pool.
+	 */
+	vmalloc_sync_all();
+
+	return gen_pool_add(ghes_estatus_pool, addr, PAGE_ALIGN(len), -1);
 }
 
 static struct ghes *ghes_new(struct acpi_hest_generic *generic)
-- 
2.20.1

[PATCH AUTOSEL 4.4 66/68] scsi: libsas: Check SMP PHY control function result

[Sasha Levin]

From: John Garry <john.garry@huawei.com>

[ Upstream commit 01929a65dfa13e18d89264ab1378854a91857e59 ]

Currently the SMP PHY control execution result is checked, however the
function result for the command is not.

As such, we may be missing all potential errors, like SMP FUNCTION FAILED,
INVALID REQUEST FRAME LENGTH, etc., meaning the PHY control request has
failed.

In some scenarios we need to ensure the function result is accepted, so add
a check for this.

Tested-by: Jian Luo <luojian5@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/libsas/sas_expander.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/drivers/scsi/libsas/sas_expander.c b/drivers/scsi/libsas/sas_expander.c
index ba16231665a5e..091af5c1cf50f 100644
--- a/drivers/scsi/libsas/sas_expander.c
+++ b/drivers/scsi/libsas/sas_expander.c
@@ -603,7 +603,14 @@ int sas_smp_phy_control(struct domain_device *dev, int phy_id,
 	}
 
 	res = smp_execute_task(dev, pc_req, PC_REQ_SIZE, pc_resp,PC_RESP_SIZE);
-
+	if (res) {
+		pr_err("ex %016llx phy%02d PHY control failed: %d\n",
+		       SAS_ADDR(dev->sas_addr), phy_id, res);
+	} else if (pc_resp[2] != SMP_RESP_FUNC_ACC) {
+		pr_err("ex %016llx phy%02d PHY control failed: function result 0x%x\n",
+		       SAS_ADDR(dev->sas_addr), phy_id, pc_resp[2]);
+		res = pc_resp[2];
+	}
 	kfree(pc_resp);
 	kfree(pc_req);
 	return res;
-- 
2.20.1

[PATCH AUTOSEL 4.4 67/68] powerpc/pseries/dlpar: Fix a missing check in dlpar_parse_cc_property()

[Sasha Levin]

From: Gen Zhang <blackgod016574@gmail.com>

[ Upstream commit efa9ace68e487ddd29c2b4d6dd23242158f1f607 ]

In dlpar_parse_cc_property(), 'prop->name' is allocated by kstrdup().
kstrdup() may return NULL, so it should be checked and handle error.
And prop should be freed if 'prop->name' is NULL.

Signed-off-by: Gen Zhang <blackgod016574@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/powerpc/platforms/pseries/dlpar.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/powerpc/platforms/pseries/dlpar.c b/arch/powerpc/platforms/pseries/dlpar.c
index a8efed3b46916..551ba5b35df9d 100644
--- a/arch/powerpc/platforms/pseries/dlpar.c
+++ b/arch/powerpc/platforms/pseries/dlpar.c
@@ -55,6 +55,10 @@ static struct property *dlpar_parse_cc_property(struct cc_workarea *ccwa)
 
 	name = (char *)ccwa + be32_to_cpu(ccwa->name_offset);
 	prop->name = kstrdup(name, GFP_KERNEL);
+	if (!prop->name) {
+		dlpar_free_cc_property(prop);
+		return NULL;
+	}
 
 	prop->length = be32_to_cpu(ccwa->prop_length);
 	value = (char *)ccwa + be32_to_cpu(ccwa->prop_offset);
-- 
2.20.1

[PATCH AUTOSEL 4.4 68/68] mtd: Remove a debug trace in mtdpart.c

[Sasha Levin]

From: Boris Brezillon <bbrezillon@kernel.org>

[ Upstream commit bda2ab56356b9acdfab150f31c4bac9846253092 ]

Commit 2b6f0090a333 ("mtd: Check add_mtd_device() ret code") contained
a leftover of the debug session that led to this bug fix. Remove this
pr_info().

Fixes: 2b6f0090a333 ("mtd: Check add_mtd_device() ret code")
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/mtd/mtdpart.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/drivers/mtd/mtdpart.c b/drivers/mtd/mtdpart.c
index 9b48be05cd1af..59772510452a5 100644
--- a/drivers/mtd/mtdpart.c
+++ b/drivers/mtd/mtdpart.c
@@ -624,7 +624,6 @@ int mtd_add_partition(struct mtd_info *master, const char *name,
 	mutex_unlock(&mtd_partitions_mutex);
 
 	free_partition(new);
-	pr_info("%s:%i\n", __func__, __LINE__);
 
 	return ret;
 }
-- 
2.20.1