* [PATCH 0/2] Increase CPU frequency in Exynos5422/5800 SoCs [not found] <CGME20191210114035eucas1p213dc81b3934969baf2bb9235d5ab8d28@eucas1p2.samsung.com> @ 2019-12-10 11:40 ` Marek Szyprowski [not found] ` <CGME20191210114036eucas1p2b0205a5dcdf1f26485235a232a5cbf20@eucas1p2.samsung.com> ` (2 more replies) 0 siblings, 3 replies; 4+ messages in thread From: Marek Szyprowski @ 2019-12-10 11:40 UTC (permalink / raw) To: linux-samsung-soc, linux-kernel, linux-pm Cc: Marek Szyprowski, Krzysztof Kozlowski, Bartlomiej Zolnierkiewicz, Kamil Konieczny, Chanwoo Choi, Doug Anderson, Andreas Faerber, Arjun K V Dear All, This patchset is a resurrection of the patch posted about 3 years ago: https://patchwork.kernel.org/patch/9475909/ That time it was not possible to merge it, because a few minor pieces were still missing in mainline kernel. This has been finally resolved and there should be no blockers for adding the higher CPU frequencies in Exynos5422/5800 SoCs: 1. support for coupled regulators (and all its dependencies) landed in the regulator framework and patch #1 adds needed coupling for the Exynos5422/5800 based boards; 2. support for the Exynos ASV has been merged to v5.4 Patches has been rebased onto the v5.5-rc1 kernel release. They were tested on the following boards: Odroid XU3, XU3-lite, XU4, HC1 and Chromebook Pi. Best regards Marek Szyprowski Samsung R&D Institute Poland Patch summary: Bartlomiej Zolnierkiewicz (1): ARM: dts: exynos: Add missing CPU frequencies for Exynos5422/5800 Marek Szyprowski (1): ARM: dts: exynos: Add initial data for coupled regulators for Exynos5422/5800 arch/arm/boot/dts/exynos5420.dtsi | 34 ++++---- arch/arm/boot/dts/exynos5422-odroid-core.dtsi | 4 + arch/arm/boot/dts/exynos5422-odroidhc1.dts | 64 +++++++-------- .../boot/dts/exynos5422-odroidxu3-common.dtsi | 78 +++++++++---------- .../boot/dts/exynos5422-odroidxu3-lite.dts | 58 ++++++++++++++ arch/arm/boot/dts/exynos5800-peach-pi.dts | 13 ++++ arch/arm/boot/dts/exynos5800.dtsi | 52 +++++++++---- 7 files changed, 199 insertions(+), 104 deletions(-) -- 2.17.1 ^ permalink raw reply [flat|nested] 4+ messages in thread
[parent not found: <CGME20191210114036eucas1p2b0205a5dcdf1f26485235a232a5cbf20@eucas1p2.samsung.com>]
* [PATCH 1/2] ARM: dts: exynos: Add initial data for coupled regulators for Exynos5422/5800 [not found] ` <CGME20191210114036eucas1p2b0205a5dcdf1f26485235a232a5cbf20@eucas1p2.samsung.com> @ 2019-12-10 11:40 ` Marek Szyprowski 0 siblings, 0 replies; 4+ messages in thread From: Marek Szyprowski @ 2019-12-10 11:40 UTC (permalink / raw) To: linux-samsung-soc, linux-kernel, linux-pm Cc: Marek Szyprowski, Krzysztof Kozlowski, Bartlomiej Zolnierkiewicz, Kamil Konieczny, Chanwoo Choi, Doug Anderson, Andreas Faerber, Arjun K V Declare Exynos5422/5800 voltage ranges for opp points for big cpu core and bus wcore and couple their voltage supllies as vdd_arm and vdd_int should be in 300mV range. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> [k.konieczny: add missing patch description] Signed-off-by: Kamil Konieczny <k.konieczny@samsung.com> Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com> --- This patch is the same as https://patchwork.kernel.org/patch/11172427/ which has been dropped due to the other issues in the regulator framework. Those issues has been resolved now, so it is safe to apply it. --- arch/arm/boot/dts/exynos5420.dtsi | 34 +++++++++---------- arch/arm/boot/dts/exynos5422-odroid-core.dtsi | 4 +++ arch/arm/boot/dts/exynos5800-peach-pi.dts | 4 +++ arch/arm/boot/dts/exynos5800.dtsi | 32 ++++++++--------- 4 files changed, 41 insertions(+), 33 deletions(-) diff --git a/arch/arm/boot/dts/exynos5420.dtsi b/arch/arm/boot/dts/exynos5420.dtsi index d39907a41f78..1ae5211f7d79 100644 --- a/arch/arm/boot/dts/exynos5420.dtsi +++ b/arch/arm/boot/dts/exynos5420.dtsi @@ -48,62 +48,62 @@ opp-1800000000 { opp-hz = /bits/ 64 <1800000000>; - opp-microvolt = <1250000>; + opp-microvolt = <1250000 1250000 1500000>; clock-latency-ns = <140000>; }; opp-1700000000 { opp-hz = /bits/ 64 <1700000000>; - opp-microvolt = <1212500>; + opp-microvolt = <1212500 1212500 1500000>; clock-latency-ns = <140000>; }; opp-1600000000 { opp-hz = /bits/ 64 <1600000000>; - opp-microvolt = <1175000>; + opp-microvolt = <1175000 1175000 1500000>; clock-latency-ns = <140000>; }; opp-1500000000 { opp-hz = /bits/ 64 <1500000000>; - opp-microvolt = <1137500>; + opp-microvolt = <1137500 1137500 1500000>; clock-latency-ns = <140000>; }; opp-1400000000 { opp-hz = /bits/ 64 <1400000000>; - opp-microvolt = <1112500>; + opp-microvolt = <1112500 1112500 1500000>; clock-latency-ns = <140000>; }; opp-1300000000 { opp-hz = /bits/ 64 <1300000000>; - opp-microvolt = <1062500>; + opp-microvolt = <1062500 1062500 1500000>; clock-latency-ns = <140000>; }; opp-1200000000 { opp-hz = /bits/ 64 <1200000000>; - opp-microvolt = <1037500>; + opp-microvolt = <1037500 1037500 1500000>; clock-latency-ns = <140000>; }; opp-1100000000 { opp-hz = /bits/ 64 <1100000000>; - opp-microvolt = <1012500>; + opp-microvolt = <1012500 1012500 1500000>; clock-latency-ns = <140000>; }; opp-1000000000 { opp-hz = /bits/ 64 <1000000000>; - opp-microvolt = < 987500>; + opp-microvolt = < 987500 987500 1500000>; clock-latency-ns = <140000>; }; opp-900000000 { opp-hz = /bits/ 64 <900000000>; - opp-microvolt = < 962500>; + opp-microvolt = < 962500 962500 1500000>; clock-latency-ns = <140000>; }; opp-800000000 { opp-hz = /bits/ 64 <800000000>; - opp-microvolt = < 937500>; + opp-microvolt = < 937500 937500 1500000>; clock-latency-ns = <140000>; }; opp-700000000 { opp-hz = /bits/ 64 <700000000>; - opp-microvolt = < 912500>; + opp-microvolt = < 912500 912500 1500000>; clock-latency-ns = <140000>; }; }; @@ -1171,23 +1171,23 @@ opp00 { opp-hz = /bits/ 64 <84000000>; - opp-microvolt = <925000>; + opp-microvolt = <925000 925000 1400000>; }; opp01 { opp-hz = /bits/ 64 <111000000>; - opp-microvolt = <950000>; + opp-microvolt = <950000 950000 1400000>; }; opp02 { opp-hz = /bits/ 64 <222000000>; - opp-microvolt = <950000>; + opp-microvolt = <950000 950000 1400000>; }; opp03 { opp-hz = /bits/ 64 <333000000>; - opp-microvolt = <950000>; + opp-microvolt = <950000 950000 1400000>; }; opp04 { opp-hz = /bits/ 64 <400000000>; - opp-microvolt = <987500>; + opp-microvolt = <987500 987500 1400000>; }; }; diff --git a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi index 059fa32d1a8f..8a34a861c191 100644 --- a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi +++ b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi @@ -601,6 +601,8 @@ regulator-max-microvolt = <1500000>; regulator-always-on; regulator-boot-on; + regulator-coupled-with = <&buck3_reg>; + regulator-coupled-max-spread = <300000>; regulator-state-mem { regulator-off-in-suspend; @@ -613,6 +615,8 @@ regulator-max-microvolt = <1400000>; regulator-always-on; regulator-boot-on; + regulator-coupled-with = <&buck2_reg>; + regulator-coupled-max-spread = <300000>; regulator-state-mem { regulator-off-in-suspend; diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts index 60ca3d685247..c1e38139ce4f 100644 --- a/arch/arm/boot/dts/exynos5800-peach-pi.dts +++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts @@ -257,6 +257,8 @@ regulator-always-on; regulator-boot-on; regulator-ramp-delay = <12500>; + regulator-coupled-with = <&buck3_reg>; + regulator-coupled-max-spread = <300000>; regulator-state-mem { regulator-off-in-suspend; }; @@ -269,6 +271,8 @@ regulator-always-on; regulator-boot-on; regulator-ramp-delay = <12500>; + regulator-coupled-with = <&buck2_reg>; + regulator-coupled-max-spread = <300000>; regulator-state-mem { regulator-off-in-suspend; }; diff --git a/arch/arm/boot/dts/exynos5800.dtsi b/arch/arm/boot/dts/exynos5800.dtsi index 16177d815ee4..1be7eb60439a 100644 --- a/arch/arm/boot/dts/exynos5800.dtsi +++ b/arch/arm/boot/dts/exynos5800.dtsi @@ -22,61 +22,61 @@ &cluster_a15_opp_table { opp-1700000000 { - opp-microvolt = <1250000>; + opp-microvolt = <1250000 1250000 1500000>; }; opp-1600000000 { - opp-microvolt = <1250000>; + opp-microvolt = <1250000 1250000 1500000>; }; opp-1500000000 { - opp-microvolt = <1100000>; + opp-microvolt = <1100000 1100000 1500000>; }; opp-1400000000 { - opp-microvolt = <1100000>; + opp-microvolt = <1100000 1100000 1500000>; }; opp-1300000000 { - opp-microvolt = <1100000>; + opp-microvolt = <1100000 1100000 1500000>; }; opp-1200000000 { - opp-microvolt = <1000000>; + opp-microvolt = <1000000 1000000 1500000>; }; opp-1100000000 { - opp-microvolt = <1000000>; + opp-microvolt = <1000000 1000000 1500000>; }; opp-1000000000 { - opp-microvolt = <1000000>; + opp-microvolt = <1000000 1000000 1500000>; }; opp-900000000 { - opp-microvolt = <1000000>; + opp-microvolt = <1000000 1000000 1500000>; }; opp-800000000 { - opp-microvolt = <900000>; + opp-microvolt = <900000 900000 1500000>; }; opp-700000000 { - opp-microvolt = <900000>; + opp-microvolt = <900000 900000 1500000>; }; opp-600000000 { opp-hz = /bits/ 64 <600000000>; - opp-microvolt = <900000>; + opp-microvolt = <900000 900000 1500000>; clock-latency-ns = <140000>; }; opp-500000000 { opp-hz = /bits/ 64 <500000000>; - opp-microvolt = <900000>; + opp-microvolt = <900000 900000 1500000>; clock-latency-ns = <140000>; }; opp-400000000 { opp-hz = /bits/ 64 <400000000>; - opp-microvolt = <900000>; + opp-microvolt = <900000 900000 1500000>; clock-latency-ns = <140000>; }; opp-300000000 { opp-hz = /bits/ 64 <300000000>; - opp-microvolt = <900000>; + opp-microvolt = <900000 900000 1500000>; clock-latency-ns = <140000>; }; opp-200000000 { opp-hz = /bits/ 64 <200000000>; - opp-microvolt = <900000>; + opp-microvolt = <900000 900000 1500000>; clock-latency-ns = <140000>; }; }; -- 2.17.1 ^ permalink raw reply related [flat|nested] 4+ messages in thread
[parent not found: <CGME20191210114036eucas1p2fe31f68148688632d983e27bed12e7d8@eucas1p2.samsung.com>]
* [PATCH 2/2] ARM: dts: exynos: Add missing CPU frequencies for Exynos5422/5800 [not found] ` <CGME20191210114036eucas1p2fe31f68148688632d983e27bed12e7d8@eucas1p2.samsung.com> @ 2019-12-10 11:40 ` Marek Szyprowski 0 siblings, 0 replies; 4+ messages in thread From: Marek Szyprowski @ 2019-12-10 11:40 UTC (permalink / raw) To: linux-samsung-soc, linux-kernel, linux-pm Cc: Marek Szyprowski, Krzysztof Kozlowski, Bartlomiej Zolnierkiewicz, Kamil Konieczny, Chanwoo Choi, Doug Anderson, Andreas Faerber, Arjun K V From: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Add missing 2.0GHz, 1.9GHz & 1.8GHz OPPs (for A15 cores) and 1.4GHz OPP (for A7 cores). Also update common Odroid-XU3 Lite/XU3/XU4 thermal cooling maps to account for new OPPs. Since some new OPPs are not available on all Exynos5422/5800 boards modify dts files for Odroid XU3 Lite (limited to 1.8 GHz / 1.3 GHz) & Peach Pi (limited to 2.0 GHz / 1.3 GHz) accordingly. This patch uses maximum voltages for new OPPs. This is a temporary solution till proper Exynos ASV support is added. Also while at it fix the number of cooling down steps for big cores (should be 11 instead of 12 on Odroid XU3 Lite and 14 on XU3/XU4). Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> [mszyprow: rebased onto v5.5-rc1 and adapted to recent dts changes, fixed removal of the 1.4GHz OPP for A7s on Peach-Pi] Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> --- Based on the patch from 15th Dec 2016: https://patchwork.kernel.org/patch/9475909/ --- arch/arm/boot/dts/exynos5422-odroidhc1.dts | 64 +++++++-------- .../boot/dts/exynos5422-odroidxu3-common.dtsi | 78 +++++++++---------- .../boot/dts/exynos5422-odroidxu3-lite.dts | 58 ++++++++++++++ arch/arm/boot/dts/exynos5800-peach-pi.dts | 9 +++ arch/arm/boot/dts/exynos5800.dtsi | 20 +++++ 5 files changed, 158 insertions(+), 71 deletions(-) diff --git a/arch/arm/boot/dts/exynos5422-odroidhc1.dts b/arch/arm/boot/dts/exynos5422-odroidhc1.dts index d271e7548826..f163206265bb 100644 --- a/arch/arm/boot/dts/exynos5422-odroidhc1.dts +++ b/arch/arm/boot/dts/exynos5422-odroidhc1.dts @@ -72,14 +72,14 @@ */ map1 { trip = <&cpu0_alert1>; - cooling-device = <&cpu0 3 7>, - <&cpu1 3 7>, - <&cpu2 3 7>, - <&cpu3 3 7>, - <&cpu4 3 12>, - <&cpu5 3 12>, - <&cpu6 3 12>, - <&cpu7 3 12>; + cooling-device = <&cpu0 3 8>, + <&cpu1 3 8>, + <&cpu2 3 8>, + <&cpu3 3 8>, + <&cpu4 3 14>, + <&cpu5 3 14>, + <&cpu6 3 14>, + <&cpu7 3 14>; }; }; }; @@ -116,14 +116,14 @@ }; map1 { trip = <&cpu1_alert1>; - cooling-device = <&cpu0 3 7>, - <&cpu1 3 7>, - <&cpu2 3 7>, - <&cpu3 3 7>, - <&cpu4 3 12>, - <&cpu5 3 12>, - <&cpu6 3 12>, - <&cpu7 3 12>; + cooling-device = <&cpu0 3 8>, + <&cpu1 3 8>, + <&cpu2 3 8>, + <&cpu3 3 8>, + <&cpu4 3 14>, + <&cpu5 3 14>, + <&cpu6 3 14>, + <&cpu7 3 14>; }; }; }; @@ -160,14 +160,14 @@ }; map1 { trip = <&cpu2_alert1>; - cooling-device = <&cpu0 3 7>, - <&cpu1 3 7>, - <&cpu2 3 7>, - <&cpu3 3 7>, - <&cpu4 3 12>, - <&cpu5 3 12>, - <&cpu6 3 12>, - <&cpu7 3 12>; + cooling-device = <&cpu0 3 8>, + <&cpu1 3 8>, + <&cpu2 3 8>, + <&cpu3 3 8>, + <&cpu4 3 14>, + <&cpu5 3 14>, + <&cpu6 3 14>, + <&cpu7 3 14>; }; }; }; @@ -204,14 +204,14 @@ }; map1 { trip = <&cpu3_alert1>; - cooling-device = <&cpu0 3 7>, - <&cpu1 3 7>, - <&cpu2 3 7>, - <&cpu3 3 7>, - <&cpu4 3 12>, - <&cpu5 3 12>, - <&cpu6 3 12>, - <&cpu7 3 12>; + cooling-device = <&cpu0 3 8>, + <&cpu1 3 8>, + <&cpu2 3 8>, + <&cpu3 3 8>, + <&cpu4 3 14>, + <&cpu5 3 14>, + <&cpu6 3 14>, + <&cpu7 3 14>; }; }; }; diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi index 838872037493..1865a708b49f 100644 --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi @@ -107,7 +107,7 @@ /* * When reaching cpu0_alert3, reduce CPU * by 2 steps. On Exynos5422/5800 that would - * be: 1600 MHz and 1100 MHz. + * (usually) be: 1800 MHz and 1200 MHz. */ map3 { trip = <&cpu0_alert3>; @@ -122,19 +122,19 @@ }; /* * When reaching cpu0_alert4, reduce CPU - * further, down to 600 MHz (12 steps for big, - * 7 steps for LITTLE). + * further, down to 600 MHz (14 steps for big, + * 8 steps for LITTLE). */ - map4 { + cpu0_cooling_map4: map4 { trip = <&cpu0_alert4>; - cooling-device = <&cpu0 3 7>, - <&cpu1 3 7>, - <&cpu2 3 7>, - <&cpu3 3 7>, - <&cpu4 3 12>, - <&cpu5 3 12>, - <&cpu6 3 12>, - <&cpu7 3 12>; + cooling-device = <&cpu0 3 8>, + <&cpu1 3 8>, + <&cpu2 3 8>, + <&cpu3 3 8>, + <&cpu4 3 14>, + <&cpu5 3 14>, + <&cpu6 3 14>, + <&cpu7 3 14>; }; }; }; @@ -198,16 +198,16 @@ <&cpu6 0 2>, <&cpu7 0 2>; }; - map4 { + cpu1_cooling_map4: map4 { trip = <&cpu1_alert4>; - cooling-device = <&cpu0 3 7>, - <&cpu1 3 7>, - <&cpu2 3 7>, - <&cpu3 3 7>, - <&cpu4 3 12>, - <&cpu5 3 12>, - <&cpu6 3 12>, - <&cpu7 3 12>; + cooling-device = <&cpu0 3 8>, + <&cpu1 3 8>, + <&cpu2 3 8>, + <&cpu3 3 8>, + <&cpu4 3 14>, + <&cpu5 3 14>, + <&cpu6 3 14>, + <&cpu7 3 14>; }; }; }; @@ -271,16 +271,16 @@ <&cpu6 0 2>, <&cpu7 0 2>; }; - map4 { + cpu2_cooling_map4: map4 { trip = <&cpu2_alert4>; - cooling-device = <&cpu0 3 7>, - <&cpu1 3 7>, - <&cpu2 3 7>, - <&cpu3 3 7>, - <&cpu4 3 12>, - <&cpu5 3 12>, - <&cpu6 3 12>, - <&cpu7 3 12>; + cooling-device = <&cpu0 3 8>, + <&cpu1 3 8>, + <&cpu2 3 8>, + <&cpu3 3 8>, + <&cpu4 3 14>, + <&cpu5 3 14>, + <&cpu6 3 14>, + <&cpu7 3 14>; }; }; }; @@ -344,16 +344,16 @@ <&cpu6 0 2>, <&cpu7 0 2>; }; - map4 { + cpu3_cooling_map4: map4 { trip = <&cpu3_alert4>; - cooling-device = <&cpu0 3 7>, - <&cpu1 3 7>, - <&cpu2 3 7>, - <&cpu3 3 7>, - <&cpu4 3 12>, - <&cpu5 3 12>, - <&cpu6 3 12>, - <&cpu7 3 12>; + cooling-device = <&cpu0 3 8>, + <&cpu1 3 8>, + <&cpu2 3 8>, + <&cpu3 3 8>, + <&cpu4 3 14>, + <&cpu5 3 14>, + <&cpu6 3 14>, + <&cpu7 3 14>; }; }; }; diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts b/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts index a31ca2ef750f..98feecad5489 100644 --- a/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts @@ -30,6 +30,64 @@ samsung,asv-bin = <2>; }; +/* + * Odroid XU3-Lite board uses SoC revision with lower maximum frequencies + * than Odroid XU3/XU4 boards: 1.8 GHz for A15 cores & 1.3 GHz for A7 cores. + * Therefore we need to update OPPs tables and thermal maps accordingly. + */ +&cluster_a15_opp_table { + /delete-node/opp-2000000000; + /delete-node/opp-1900000000; +}; + +&cluster_a7_opp_table { + /delete-node/opp-1400000000; +}; + +&cpu0_cooling_map4 { + cooling-device = <&cpu0 3 7>, + <&cpu1 3 7>, + <&cpu2 3 7>, + <&cpu3 3 7>, + <&cpu4 3 12>, + <&cpu5 3 12>, + <&cpu6 3 12>, + <&cpu7 3 12>; +}; + +&cpu1_cooling_map4 { + cooling-device = <&cpu0 3 7>, + <&cpu1 3 7>, + <&cpu2 3 7>, + <&cpu3 3 7>, + <&cpu4 3 12>, + <&cpu5 3 12>, + <&cpu6 3 12>, + <&cpu7 3 12>; +}; + +&cpu2_cooling_map4 { + cooling-device = <&cpu0 3 7>, + <&cpu1 3 7>, + <&cpu2 3 7>, + <&cpu3 3 7>, + <&cpu4 3 12>, + <&cpu5 3 12>, + <&cpu6 3 12>, + <&cpu7 3 12>; +}; + +&cpu3_cooling_map4 { + cooling-device = <&cpu0 3 7>, + <&cpu1 3 7>, + <&cpu2 3 7>, + <&cpu3 3 7>, + <&cpu4 3 12>, + <&cpu5 3 12>, + <&cpu6 3 12>, + <&cpu7 3 12>; +}; + &pwm { /* * PWM 0 -- fan diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts index c1e38139ce4f..60ab0effe474 100644 --- a/arch/arm/boot/dts/exynos5800-peach-pi.dts +++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts @@ -156,6 +156,15 @@ assigned-clock-parents = <&clock CLK_MAU_EPLL>; }; +/* + * Peach Pi board uses SoC revision with lower maximum frequency for A7 cores + * (1.3 GHz instead of 1.4 GHz) than Odroid XU3/XU4 boards. Thus we need to + * update A7 OPPs table accordingly. + */ +&cluster_a7_opp_table { + /delete-node/opp-1400000000; +}; + &cpu0 { cpu-supply = <&buck2_reg>; }; diff --git a/arch/arm/boot/dts/exynos5800.dtsi b/arch/arm/boot/dts/exynos5800.dtsi index 1be7eb60439a..b4fd53496450 100644 --- a/arch/arm/boot/dts/exynos5800.dtsi +++ b/arch/arm/boot/dts/exynos5800.dtsi @@ -21,6 +21,21 @@ }; &cluster_a15_opp_table { + opp-2000000000 { + opp-hz = /bits/ 64 <2000000000>; + opp-microvolt = <1312500>; + clock-latency-ns = <140000>; + }; + opp-1900000000 { + opp-hz = /bits/ 64 <1900000000>; + opp-microvolt = <1262500>; + clock-latency-ns = <140000>; + }; + opp-1800000000 { + opp-hz = /bits/ 64 <1800000000>; + opp-microvolt = <1237500>; + clock-latency-ns = <140000>; + }; opp-1700000000 { opp-microvolt = <1250000 1250000 1500000>; }; @@ -82,6 +97,11 @@ }; &cluster_a7_opp_table { + opp-1400000000 { + opp-hz = /bits/ 64 <1400000000>; + opp-microvolt = <1275000>; + clock-latency-ns = <140000>; + }; opp-1300000000 { opp-microvolt = <1250000>; }; -- 2.17.1 ^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH 0/2] Increase CPU frequency in Exynos5422/5800 SoCs 2019-12-10 11:40 ` [PATCH 0/2] Increase CPU frequency in Exynos5422/5800 SoCs Marek Szyprowski [not found] ` <CGME20191210114036eucas1p2b0205a5dcdf1f26485235a232a5cbf20@eucas1p2.samsung.com> [not found] ` <CGME20191210114036eucas1p2fe31f68148688632d983e27bed12e7d8@eucas1p2.samsung.com> @ 2019-12-11 18:20 ` Krzysztof Kozlowski 2 siblings, 0 replies; 4+ messages in thread From: Krzysztof Kozlowski @ 2019-12-11 18:20 UTC (permalink / raw) To: Marek Szyprowski Cc: linux-samsung-soc, linux-kernel, linux-pm, Bartlomiej Zolnierkiewicz, Kamil Konieczny, Chanwoo Choi, Doug Anderson, Andreas Faerber, Arjun K V On Tue, Dec 10, 2019 at 12:40:25PM +0100, Marek Szyprowski wrote: > Dear All, > > This patchset is a resurrection of the patch posted about 3 years ago: > https://patchwork.kernel.org/patch/9475909/ > > That time it was not possible to merge it, because a few minor pieces > were still missing in mainline kernel. This has been finally resolved > and there should be no blockers for adding the higher CPU frequencies > in Exynos5422/5800 SoCs: > > 1. support for coupled regulators (and all its dependencies) landed > in the regulator framework and patch #1 adds needed coupling for > the Exynos5422/5800 based boards; > > 2. support for the Exynos ASV has been merged to v5.4 > > Patches has been rebased onto the v5.5-rc1 kernel release. They were > tested on the following boards: Odroid XU3, XU3-lite, XU4, HC1 and > Chromebook Pi. > > Best regards > Marek Szyprowski > Samsung R&D Institute Poland > Thanks, applied both. Best regards, Krzysztof ^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2019-12-11 18:20 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
[not found] <CGME20191210114035eucas1p213dc81b3934969baf2bb9235d5ab8d28@eucas1p2.samsung.com>
2019-12-10 11:40 ` [PATCH 0/2] Increase CPU frequency in Exynos5422/5800 SoCs Marek Szyprowski
[not found] ` <CGME20191210114036eucas1p2b0205a5dcdf1f26485235a232a5cbf20@eucas1p2.samsung.com>
2019-12-10 11:40 ` [PATCH 1/2] ARM: dts: exynos: Add initial data for coupled regulators for Exynos5422/5800 Marek Szyprowski
[not found] ` <CGME20191210114036eucas1p2fe31f68148688632d983e27bed12e7d8@eucas1p2.samsung.com>
2019-12-10 11:40 ` [PATCH 2/2] ARM: dts: exynos: Add missing CPU frequencies " Marek Szyprowski
2019-12-11 18:20 ` [PATCH 0/2] Increase CPU frequency in Exynos5422/5800 SoCs Krzysztof Kozlowski
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).