Re: [PATCH 3/4] media: ov5647: Add support for non-continuous clock mode

From: Sakari Ailus <sakari.ailus@linux.intel.com>
To: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
Cc: linux-kernel@vger.kernel.org, linux-media@vger.kernel.org,
	linux-renesas-soc@vger.kernel.org,
	"Luis Oliveira" <lolivei@synopsys.com>,
	"Niklas Söderlund" <niklas.soderlund@ragnatech.se>,
	"Jacopo Mondi" <jacopo@jmondi.org>,
	"Michael Rodin" <mrodin@de.adit-jv.com>,
	"Mauro Carvalho Chehab" <mchehab@kernel.org>,
	"Hugues Fruchet" <hugues.fruchet@st.com>,
	"Maxime Ripard" <mripard@kernel.org>,
	"Adam Ford" <aford173@gmail.com>,
	"Todor Tomov" <todor.tomov@linaro.org>,
	"Suresh Udipi" <sudipi@jp.adit-jv.com>,
	"Andrew Gabbasov" <andrew_gabbasov@mentor.com>,
	"Eugeniu Rosca" <erosca@de.adit-jv.com>,
	"Dave Stevenson" <dave.stevenson@raspberrypi.org>
Subject: Re: [PATCH 3/4] media: ov5647: Add support for non-continuous clock mode
Date: Thu, 23 Apr 2020 10:47:13 +0300	[thread overview]
Message-ID: <20200423074713.GK5381@paasikivi.fi.intel.com> (raw)
In-Reply-To: <c3189c80ac27d67e814509d44a864f8164971efb.1586759968.git.roman.kovalivskyi@globallogic.com>

Hi Roman,

On Mon, Apr 13, 2020 at 12:17:46PM +0300, Roman Kovalivskyi wrote:
> From: Dave Stevenson <dave.stevenson@raspberrypi.org>
> 
> The driver was only supporting continuous clock mode
> although this was not stated anywhere.
> Non-continuous clock saves a small amount of power and
> on some SoCs is easier to interface with.
> 
> Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
> Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
> ---
>  drivers/media/i2c/ov5647.c | 17 ++++++++++++++---
>  1 file changed, 14 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/media/i2c/ov5647.c b/drivers/media/i2c/ov5647.c
> index c39e3d20e3ef..8a1a515388e0 100644
> --- a/drivers/media/i2c/ov5647.c
> +++ b/drivers/media/i2c/ov5647.c
> @@ -44,6 +44,7 @@
>  #define PWDN_ACTIVE_DELAY_MS	20
>  
>  #define MIPI_CTRL00_CLOCK_LANE_GATE		BIT(5)
> +#define MIPI_CTRL00_LINE_SYNC_ENABLE		BIT(4)
>  #define MIPI_CTRL00_BUS_IDLE			BIT(2)
>  #define MIPI_CTRL00_CLOCK_LANE_DISABLE		BIT(0)
>  
> @@ -95,6 +96,7 @@ struct ov5647 {
>  	int				power_count;
>  	struct clk			*xclk;
>  	struct gpio_desc		*pwdn;
> +	unsigned int			flags;
>  };
>  
>  static inline struct ov5647 *to_state(struct v4l2_subdev *sd)
> @@ -269,9 +271,15 @@ static int ov5647_set_virtual_channel(struct v4l2_subdev *sd, int channel)
>  
>  static int ov5647_stream_on(struct v4l2_subdev *sd)
>  {
> +	struct ov5647 *ov5647 = to_state(sd);
> +	u8 val = MIPI_CTRL00_BUS_IDLE;
>  	int ret;
>  
> -	ret = ov5647_write(sd, OV5647_REG_MIPI_CTRL00, MIPI_CTRL00_BUS_IDLE);
> +	if (ov5647->flags & V4L2_MBUS_CSI2_NONCONTINUOUS_CLOCK)
> +		val |= MIPI_CTRL00_CLOCK_LANE_GATE |
> +		       MIPI_CTRL00_LINE_SYNC_ENABLE;
> +
> +	ret = ov5647_write(sd, OV5647_REG_MIPI_CTRL00, val);
>  	if (ret < 0)
>  		return ret;
>  
> @@ -568,7 +576,7 @@ static const struct v4l2_subdev_internal_ops ov5647_subdev_internal_ops = {
>  	.open = ov5647_open,
>  };
>  
> -static int ov5647_parse_dt(struct device_node *np)
> +static int ov5647_parse_dt(struct device_node *np, struct ov5647 *sensor)
>  {
>  	struct v4l2_fwnode_endpoint bus_cfg = { .bus_type = 0 };

The bus type should be set to V4L2_MBUS_CSI2_DPHY here; 0 is just for
compatibility with the old heuristics.

>  	struct device_node *ep;
> @@ -581,6 +589,9 @@ static int ov5647_parse_dt(struct device_node *np)
>  
>  	ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep), &bus_cfg);
>  
> +	if (!ret)
> +		sensor->flags = bus_cfg.bus.mipi_csi2.flags;
> +
>  	of_node_put(ep);
>  	return ret;
>  }
> @@ -599,7 +610,7 @@ static int ov5647_probe(struct i2c_client *client)
>  		return -ENOMEM;
>  
>  	if (IS_ENABLED(CONFIG_OF) && np) {
> -		ret = ov5647_parse_dt(np);
> +		ret = ov5647_parse_dt(np, sensor);
>  		if (ret) {
>  			dev_err(dev, "DT parsing error: %d\n", ret);
>  			return ret;

-- 
Kind regards,

Sakari Ailus