[PATCH v2 00/19] arm64: dts: imx8: Align pins and regulators with dtschema

[PATCH v2 00/19] arm64: dts: imx8: Align pins and regulators with dtschema

[Krzysztof Kozlowski]

Hi,

This is a v2 of my second batch of i.MX8 DTS and bindings cleanup. It's
rebased on top of first batch [1] although it is independent.

1. For arm64/dts patches: to avoid any conflicts, better to apply
   on top of [1].
2. dt-bindings patches: independend, can be applied by Rob or subsystem
   maintainers.


Changes since v1:
=================
1. Address few comments - see individual patches.

[1] https://lore.kernel.org/lkml/20200825193536.7332-1-krzk@kernel.org/


Best regards,
Krzysztof


Krzysztof Kozlowski (19):
  dt-bindings: mfd: rohm,bd71847-pmic: Correct clock properties
    requirements
  dt-bindings: mtd: gpmi-nand: Fix matching of clocks on different SoCs
  arm64: dts: imx8mm-beacon-kit: Add missing build through Makefile
  arm64: dts: imx8mm-beacon-som: Align regulator names with schema
  arm64: dts: imx8mm-beacon-som: Fix atmel,24c64 EEPROM compatible
  arm64: dts: imx8mm-beacon: Align pin configuration group names with
    schema
  arm64: dts: imx8mm-evk: Align regulator names with schema
  arm64: dts: imx8mm-evk: Add 32.768 kHz clock to PMIC
  arm64: dts: imx8mm-evk: Align pin configuration group names with
    schema
  arm64: dts: imx8mm-ddr4-evk: Align pin configuration group names with
    schema
  arm64: dts: imx8mn-ddr4-evk: Align regulator names with schema
  arm64: dts: imx8mn-evk: Align pin configuration group names with
    schema
  arm64: dts: imx8mq-evk: Align pin configuration group names with
    schema
  arm64: dts: imx8mq-librem5-devkit: Align pin configuration group names
    with schema
  arm64: dts: imx8mq-phanbell: Align pin configuration group names with
    schema
  arm64: dts: imx8mq-pico-pi: Align pin configuration group names with
    schema
  arm64: dts: imx8mq-sr-som: Align pin configuration group names with
    schema
  arm64: dts: imx8mq-hummingboard-pulse: Align pin configuration group
    names with schema
  arm64: dts: imx8qxp-colibri: Align pin configuration group names with
    schema

 .../bindings/mfd/rohm,bd71847-pmic.yaml       |  9 ++-
 .../devicetree/bindings/mtd/gpmi-nand.yaml    | 76 +++++++++++++++----
 arch/arm64/boot/dts/freescale/Makefile        |  1 +
 .../freescale/imx8mm-beacon-baseboard.dtsi    |  8 +-
 .../boot/dts/freescale/imx8mm-beacon-som.dtsi | 36 ++++-----
 arch/arm64/boot/dts/freescale/imx8mm-evk.dts  | 40 +++++-----
 .../boot/dts/freescale/imx8mn-ddr4-evk.dts    | 24 +++---
 arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi | 14 ++--
 arch/arm64/boot/dts/freescale/imx8mq-evk.dts  |  2 +-
 .../freescale/imx8mq-hummingboard-pulse.dts   |  8 +-
 .../dts/freescale/imx8mq-librem5-devkit.dts   | 12 +--
 .../boot/dts/freescale/imx8mq-phanbell.dts    | 12 +--
 .../boot/dts/freescale/imx8mq-pico-pi.dts     | 12 +--
 .../boot/dts/freescale/imx8mq-sr-som.dtsi     |  4 +-
 .../boot/dts/freescale/imx8qxp-colibri.dtsi   |  8 +-
 15 files changed, 161 insertions(+), 105 deletions(-)

-- 
2.17.1

[PATCH v2 01/19] dt-bindings: mfd: rohm,bd71847-pmic: Correct clock properties requirements

[Krzysztof Kozlowski]

The input clock and number of clock provider cells are not required for
the PMIC to operate.  They are needed only for the optional bd718x7
clock driver.

Add also clock-output-names as driver takes use of it.

This fixes dtbs_check warnings like:

    arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dt.yaml: pmic@4b: 'clocks' is a required property
    arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dt.yaml: pmic@4b: '#clock-cells' is a required property

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
 .../devicetree/bindings/mfd/rohm,bd71847-pmic.yaml       | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71847-pmic.yaml b/Documentation/devicetree/bindings/mfd/rohm,bd71847-pmic.yaml
index 77bcca2d414f..5d531051a153 100644
--- a/Documentation/devicetree/bindings/mfd/rohm,bd71847-pmic.yaml
+++ b/Documentation/devicetree/bindings/mfd/rohm,bd71847-pmic.yaml
@@ -38,6 +38,9 @@ properties:
   "#clock-cells":
     const: 0
 
+  clock-output-names:
+    maxItems: 1
+
 # The BD71847 abd BD71850 support two different HW states as reset target
 # states. States are called as SNVS and READY. At READY state all the PMIC
 # power outputs go down and OTP is reload. At the SNVS state all other logic
@@ -116,12 +119,14 @@ required:
   - compatible
   - reg
   - interrupts
-  - clocks
-  - "#clock-cells"
   - regulators
 
 additionalProperties: false
 
+dependencies:
+  '#clock-cells': [clocks]
+  clocks: ['#clock-cells']
+
 examples:
   - |
     #include <dt-bindings/interrupt-controller/irq.h>
-- 
2.17.1

[PATCH v2 02/19] dt-bindings: mtd: gpmi-nand: Fix matching of clocks on different SoCs

[Krzysztof Kozlowski]

Driver requires different amount of clocks for different SoCs.  Describe
these requirements properly to fix dtbs_check warnings like:

    arch/arm64/boot/dts/freescale/imx8mm-beacon-kit.dt.yaml: nand-controller@33002000: clock-names:1: 'gpmi_apb' was expected

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

---

Changes since v1:
1. Do not require order of clocks (use pattern).
---
 .../devicetree/bindings/mtd/gpmi-nand.yaml    | 76 +++++++++++++++----
 1 file changed, 61 insertions(+), 15 deletions(-)

diff --git a/Documentation/devicetree/bindings/mtd/gpmi-nand.yaml b/Documentation/devicetree/bindings/mtd/gpmi-nand.yaml
index 28ff8c581837..e08e0a50929e 100644
--- a/Documentation/devicetree/bindings/mtd/gpmi-nand.yaml
+++ b/Documentation/devicetree/bindings/mtd/gpmi-nand.yaml
@@ -9,9 +9,6 @@ title: Freescale General-Purpose Media Interface (GPMI) binding
 maintainers:
   - Han Xu <han.xu@nxp.com>
 
-allOf:
-  - $ref: "nand-controller.yaml"
-
 description: |
   The GPMI nand controller provides an interface to control the NAND
   flash chips. The device tree may optionally contain sub-nodes
@@ -58,22 +55,10 @@ properties:
   clocks:
     minItems: 1
     maxItems: 5
-    items:
-      - description: SoC gpmi io clock
-      - description: SoC gpmi apb clock
-      - description: SoC gpmi bch clock
-      - description: SoC gpmi bch apb clock
-      - description: SoC per1 bch clock
 
   clock-names:
     minItems: 1
     maxItems: 5
-    items:
-      - const: gpmi_io
-      - const: gpmi_apb
-      - const: gpmi_bch
-      - const: gpmi_bch_apb
-      - const: per1_bch
 
   fsl,use-minimum-ecc:
     type: boolean
@@ -107,6 +92,67 @@ required:
 
 unevaluatedProperties: false
 
+allOf:
+  - $ref: "nand-controller.yaml"
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - fsl,imx23-gpmi-nand
+              - fsl,imx28-gpmi-nand
+    then:
+      properties:
+        clocks:
+          items:
+            - description: SoC gpmi io clock
+        clock-names:
+          items:
+            - const: gpmi_io
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - fsl,imx6q-gpmi-nand
+              - fsl,imx6sx-gpmi-nand
+    then:
+      properties:
+        clocks:
+          items:
+            - description: SoC gpmi io clock
+            - description: SoC gpmi apb clock
+            - description: SoC gpmi bch clock
+            - description: SoC gpmi bch apb clock
+            - description: SoC per1 bch clock
+        clock-names:
+          items:
+            - pattern: "^(gpmi_(io|apb|bch|bch_apb)|per1_bch)$"
+            - pattern: "^(gpmi_(io|apb|bch|bch_apb)|per1_bch)$"
+            - pattern: "^(gpmi_(io|apb|bch|bch_apb)|per1_bch)$"
+            - pattern: "^(gpmi_(io|apb|bch|bch_apb)|per1_bch)$"
+            - pattern: "^(gpmi_(io|apb|bch|bch_apb)|per1_bch)$"
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: fsl,imx7d-gpmi-nand
+    then:
+      properties:
+        clocks:
+          items:
+            - description: SoC gpmi io clock
+            - description: SoC gpmi bch apb clock
+        clock-names:
+          minItems: 2
+          maxItems: 2
+          items:
+            - pattern: "^gpmi_(io|bch_apb)$"
+            - pattern: "^gpmi_(io|bch_apb)$"
+
 examples:
   - |
     nand-controller@8000c000 {
-- 
2.17.1

[PATCH v2 03/19] arm64: dts: imx8mm-beacon-kit: Add missing build through Makefile

[Krzysztof Kozlowski]

Add missing imx8mm-beacon-kit.dts object in Makefile so it will be build
when building dtbs.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 arch/arm64/boot/dts/freescale/Makefile | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index a39f0a1723e0..903c0eb61290 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -28,6 +28,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-honeycomb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
 
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb
-- 
2.17.1

[PATCH v2 04/19] arm64: dts: imx8mm-beacon-som: Align regulator names with schema

[Krzysztof Kozlowski]

Device tree schema expects regulator names to be lowercase.  Changing to
lowercase has multiple effects:
1. LDO6 supply is now properly configured, because regulator driver
   looks for supplies by lowercase name,
2. User-visible names via sysfs or debugfs are now lowercase,
2. dtbs_check warnings are fixed:

    pmic@4b: regulators:LDO1:regulator-name:0: 'LDO1' does not match '^ldo[1-6]$'

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 .../boot/dts/freescale/imx8mm-beacon-som.dtsi | 22 +++++++++----------
 1 file changed, 11 insertions(+), 11 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi
index 94911b1707ef..f627e82ad929 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi
@@ -79,7 +79,7 @@
 
 		regulators {
 			buck1_reg: BUCK1 {
-				regulator-name = "BUCK1";
+				regulator-name = "buck1";
 				regulator-min-microvolt = <700000>;
 				regulator-max-microvolt = <1300000>;
 				regulator-boot-on;
@@ -88,7 +88,7 @@
 			};
 
 			buck2_reg: BUCK2 {
-				regulator-name = "BUCK2";
+				regulator-name = "buck2";
 				regulator-min-microvolt = <700000>;
 				regulator-max-microvolt = <1300000>;
 				regulator-boot-on;
@@ -100,7 +100,7 @@
 
 			buck3_reg: BUCK3 {
 				// BUCK5 in datasheet
-				regulator-name = "BUCK3";
+				regulator-name = "buck3";
 				regulator-min-microvolt = <700000>;
 				regulator-max-microvolt = <1350000>;
 				regulator-boot-on;
@@ -109,7 +109,7 @@
 
 			buck4_reg: BUCK4 {
 				// BUCK6 in datasheet
-				regulator-name = "BUCK4";
+				regulator-name = "buck4";
 				regulator-min-microvolt = <3000000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
@@ -118,7 +118,7 @@
 
 			buck5_reg: BUCK5 {
 				// BUCK7 in datasheet
-				regulator-name = "BUCK5";
+				regulator-name = "buck5";
 				regulator-min-microvolt = <1605000>;
 				regulator-max-microvolt = <1995000>;
 				regulator-boot-on;
@@ -127,7 +127,7 @@
 
 			buck6_reg: BUCK6 {
 				// BUCK8 in datasheet
-				regulator-name = "BUCK6";
+				regulator-name = "buck6";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <1400000>;
 				regulator-boot-on;
@@ -135,7 +135,7 @@
 			};
 
 			ldo1_reg: LDO1 {
-				regulator-name = "LDO1";
+				regulator-name = "ldo1";
 				regulator-min-microvolt = <1600000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
@@ -143,7 +143,7 @@
 			};
 
 			ldo2_reg: LDO2 {
-				regulator-name = "LDO2";
+				regulator-name = "ldo2";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <900000>;
 				regulator-boot-on;
@@ -151,7 +151,7 @@
 			};
 
 			ldo3_reg: LDO3 {
-				regulator-name = "LDO3";
+				regulator-name = "ldo3";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
@@ -159,7 +159,7 @@
 			};
 
 			ldo4_reg: LDO4 {
-				regulator-name = "LDO4";
+				regulator-name = "ldo4";
 				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-boot-on;
@@ -167,7 +167,7 @@
 			};
 
 			ldo6_reg: LDO6 {
-				regulator-name = "LDO6";
+				regulator-name = "ldo6";
 				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-boot-on;
-- 
2.17.1

[PATCH v2 05/19] arm64: dts: imx8mm-beacon-som: Fix atmel,24c64 EEPROM compatible

[Krzysztof Kozlowski]

Correct the EEPROM node compatible to match device tree schema (invalid
space, unknown ID) to fix dtbs_check warnings:

  arch/arm64/boot/dts/freescale/imx8mm-beacon-kit.dt.yaml: eeprom@50:
    compatible: ['microchip, at24c64d', 'atmel,24c64'] is not valid under any of the given schemas
  arch/arm64/boot/dts/freescale/imx8mm-beacon-kit.dt.yaml: eeprom@50:
    compatible:0: 'microchip, at24c64d' does not match '^[a-zA-Z][a-zA-Z0-9,+\\-._]+$'

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi
index f627e82ad929..620a124dfb5f 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi
@@ -184,7 +184,7 @@
 	status = "okay";
 
 	eeprom@50 {
-		compatible = "microchip, at24c64d", "atmel,24c64";
+		compatible = "microchip,24c64", "atmel,24c64";
 		pagesize = <32>;
 		read-only;	/* Manufacturing EEPROM programmed at factory */
 		reg = <0x50>;
-- 
2.17.1

[PATCH v2 06/19] arm64: dts: imx8mm-beacon: Align pin configuration group names with schema

[Krzysztof Kozlowski]

Device tree schema expects pin configuration groups to end with 'grp'
suffix.  This fixes dtbs_check warnings like:

  pinctrl@30330000: 'pcal6414-gpio', 'pmicirq', 'usdhc1grp100mhz', 'usdhc1grp200mhz', 'usdhc1grpgpio',
    'usdhc2grp100mhz', 'usdhc2grp200mhz', 'usdhc2grpgpio', 'usdhc3grp100mhz', 'usdhc3grp200mhz'
    do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 .../boot/dts/freescale/imx8mm-beacon-baseboard.dtsi  |  8 ++++----
 arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi | 12 ++++++------
 2 files changed, 10 insertions(+), 10 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi
index bf0859f1e1fa..16e4910aeb1e 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi
@@ -210,7 +210,7 @@
 		>;
 	};
 
-	pinctrl_pcal6414: pcal6414-gpio {
+	pinctrl_pcal6414: pcal6414-gpiogrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SAI2_MCLK_GPIO4_IO27		0x19
 		>;
@@ -240,7 +240,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_gpio: usdhc2grpgpio {
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SD2_CD_B_USDHC2_CD_B	0x41
 			MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19	0x41
@@ -259,7 +259,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK	0x194
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD	0x1d4
@@ -271,7 +271,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK	0x196
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD	0x1d6
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi
index 620a124dfb5f..502faf6144b0 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi
@@ -290,7 +290,7 @@
 			>;
 		};
 
-		pinctrl_pmic: pmicirq {
+		pinctrl_pmic: pmicirqgrp {
 			fsl,pins = <
 				MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x41
 			>;
@@ -309,7 +309,7 @@
 			>;
 		};
 
-		pinctrl_usdhc1_gpio: usdhc1grpgpio {
+		pinctrl_usdhc1_gpio: usdhc1gpiogrp {
 			fsl,pins = <
 				MX8MM_IOMUXC_SD1_RESET_B_GPIO2_IO10	0x41
 			>;
@@ -326,7 +326,7 @@
 			>;
 		};
 
-		pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+		pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
 			fsl,pins = <
 				MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK		0x194
 				MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD		0x1d4
@@ -337,7 +337,7 @@
 			>;
 		};
 
-		pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+		pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
 			fsl,pins = <
 				MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK		0x196
 				MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD		0x1d6
@@ -364,7 +364,7 @@
 			>;
 		};
 
-		pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+		pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
 			fsl,pins = <
 				MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x194
 				MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d4
@@ -380,7 +380,7 @@
 			>;
 		};
 
-		pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+		pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
 			fsl,pins = <
 				MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x196
 				MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d6
-- 
2.17.1

[PATCH v2 07/19] arm64: dts: imx8mm-evk: Align regulator names with schema

[Krzysztof Kozlowski]

Device tree schema expects regulator names to be lowercase.  Changing to
lowercase has multiple effects:
1. LDO6 supply is now properly configured, because regulator driver
   looks for supplies by lowercase name,
2. User-visible names via sysfs or debugfs are now lowercase,
2. dtbs_check warnings are fixed:

    pmic@4b: regulators:LDO1:regulator-name:0: 'LDO1' does not match '^ldo[1-6]$'

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8mm-evk.dts | 22 ++++++++++----------
 1 file changed, 11 insertions(+), 11 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
index c1f7d44651df..3cb8b6bcb657 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
@@ -151,7 +151,7 @@
 
 		regulators {
 			buck1_reg: BUCK1 {
-				regulator-name = "BUCK1";
+				regulator-name = "buck1";
 				regulator-min-microvolt = <700000>;
 				regulator-max-microvolt = <1300000>;
 				regulator-boot-on;
@@ -160,7 +160,7 @@
 			};
 
 			buck2_reg: BUCK2 {
-				regulator-name = "BUCK2";
+				regulator-name = "buck2";
 				regulator-min-microvolt = <700000>;
 				regulator-max-microvolt = <1300000>;
 				regulator-boot-on;
@@ -172,7 +172,7 @@
 
 			buck3_reg: BUCK3 {
 				// BUCK5 in datasheet
-				regulator-name = "BUCK3";
+				regulator-name = "buck3";
 				regulator-min-microvolt = <700000>;
 				regulator-max-microvolt = <1350000>;
 				regulator-boot-on;
@@ -181,7 +181,7 @@
 
 			buck4_reg: BUCK4 {
 				// BUCK6 in datasheet
-				regulator-name = "BUCK4";
+				regulator-name = "buck4";
 				regulator-min-microvolt = <3000000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
@@ -190,7 +190,7 @@
 
 			buck5_reg: BUCK5 {
 				// BUCK7 in datasheet
-				regulator-name = "BUCK5";
+				regulator-name = "buck5";
 				regulator-min-microvolt = <1605000>;
 				regulator-max-microvolt = <1995000>;
 				regulator-boot-on;
@@ -199,7 +199,7 @@
 
 			buck6_reg: BUCK6 {
 				// BUCK8 in datasheet
-				regulator-name = "BUCK6";
+				regulator-name = "buck6";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <1400000>;
 				regulator-boot-on;
@@ -207,7 +207,7 @@
 			};
 
 			ldo1_reg: LDO1 {
-				regulator-name = "LDO1";
+				regulator-name = "ldo1";
 				regulator-min-microvolt = <1600000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
@@ -215,7 +215,7 @@
 			};
 
 			ldo2_reg: LDO2 {
-				regulator-name = "LDO2";
+				regulator-name = "ldo2";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <900000>;
 				regulator-boot-on;
@@ -223,7 +223,7 @@
 			};
 
 			ldo3_reg: LDO3 {
-				regulator-name = "LDO3";
+				regulator-name = "ldo3";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
@@ -231,7 +231,7 @@
 			};
 
 			ldo4_reg: LDO4 {
-				regulator-name = "LDO4";
+				regulator-name = "ldo4";
 				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-boot-on;
@@ -239,7 +239,7 @@
 			};
 
 			ldo6_reg: LDO6 {
-				regulator-name = "LDO6";
+				regulator-name = "ldo6";
 				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-boot-on;
-- 
2.17.1

[PATCH v2 08/19] arm64: dts: imx8mm-evk: Add 32.768 kHz clock to PMIC

[Krzysztof Kozlowski]

The ROHM BD71847 PMIC has a 32.768 kHz clock.  Adding necessary parent
allows to probe the bd718x7 clock driver fixing boot errors:

    bd718xx-clk bd71847-clk.1.auto: No parent clk found
    bd718xx-clk: probe of bd71847-clk.1.auto failed with error -22

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8mm-evk.dts | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
index 3cb8b6bcb657..0115f07bbc9d 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
@@ -149,6 +149,10 @@
 		interrupts = <3 GPIO_ACTIVE_LOW>;
 		rohm,reset-snvs-powered;
 
+		#clock-cells = <0>;
+		clocks = <&osc_32k 0>;
+		clock-output-names = "clk-32k-out";
+
 		regulators {
 			buck1_reg: BUCK1 {
 				regulator-name = "buck1";
-- 
2.17.1

[PATCH v2 09/19] arm64: dts: imx8mm-evk: Align pin configuration group names with schema

[Krzysztof Kozlowski]

Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:

    ... do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8mm-evk.dts | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
index 0115f07bbc9d..207dc8de3145 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
@@ -423,13 +423,13 @@
 		>;
 	};
 
-	pinctrl_pmic: pmicirq {
+	pinctrl_pmic: pmicirqgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x41
 		>;
 	};
 
-	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
+	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19	0x41
 		>;
@@ -457,7 +457,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_gpio: usdhc2grpgpio {
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15	0x1c4
 		>;
@@ -475,7 +475,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x194
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4
@@ -487,7 +487,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x196
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d6
@@ -515,7 +515,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x194
 			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d4
@@ -531,7 +531,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x196
 			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d6
-- 
2.17.1

[PATCH v2 10/19] arm64: dts: imx8mm-ddr4-evk: Align pin configuration group names with schema

[Krzysztof Kozlowski]

Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:

    ... do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
index a1e5483dbbbe..3ac8f9d3c372 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
@@ -155,7 +155,7 @@
 };
 
 &iomuxc {
-	pinctrl_pmic: pmicirq {
+	pinctrl_pmic: pmicirqgrp {
 		fsl,pins = <
 			MX8MN_IOMUXC_GPIO1_IO03_GPIO1_IO3	0x41
 		>;
-- 
2.17.1

[PATCH v2 11/19] arm64: dts: imx8mn-ddr4-evk: Align regulator names with schema

[Krzysztof Kozlowski]

Device tree schema expects regulator names to be lowercase.  Changing to
lowercase has multiple effects:
1. LDO6 supply is now properly configured, because regulator driver
   looks for supplies by lowercase name,
2. User-visible names via sysfs or debugfs are now lowercase,
2. dtbs_check warnings are fixed:

    pmic@4b: regulators:LDO1:regulator-name:0: 'LDO1' does not match '^ldo[1-6]$'

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 .../boot/dts/freescale/imx8mn-ddr4-evk.dts    | 22 +++++++++----------
 1 file changed, 11 insertions(+), 11 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
index 3ac8f9d3c372..8f7155716c84 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
@@ -60,7 +60,7 @@
 
 		regulators {
 			buck1_reg: BUCK1 {
-				regulator-name = "BUCK1";
+				regulator-name = "buck1";
 				regulator-min-microvolt = <700000>;
 				regulator-max-microvolt = <1300000>;
 				regulator-boot-on;
@@ -69,7 +69,7 @@
 			};
 
 			buck2_reg: BUCK2 {
-				regulator-name = "BUCK2";
+				regulator-name = "buck2";
 				regulator-min-microvolt = <700000>;
 				regulator-max-microvolt = <1300000>;
 				regulator-boot-on;
@@ -79,14 +79,14 @@
 
 			buck3_reg: BUCK3 {
 				// BUCK5 in datasheet
-				regulator-name = "BUCK3";
+				regulator-name = "buck3";
 				regulator-min-microvolt = <700000>;
 				regulator-max-microvolt = <1350000>;
 			};
 
 			buck4_reg: BUCK4 {
 				// BUCK6 in datasheet
-				regulator-name = "BUCK4";
+				regulator-name = "buck4";
 				regulator-min-microvolt = <3000000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
@@ -95,7 +95,7 @@
 
 			buck5_reg: BUCK5 {
 				// BUCK7 in datasheet
-				regulator-name = "BUCK5";
+				regulator-name = "buck5";
 				regulator-min-microvolt = <1605000>;
 				regulator-max-microvolt = <1995000>;
 				regulator-boot-on;
@@ -104,7 +104,7 @@
 
 			buck6_reg: BUCK6 {
 				// BUCK8 in datasheet
-				regulator-name = "BUCK6";
+				regulator-name = "buck6";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <1400000>;
 				regulator-boot-on;
@@ -112,7 +112,7 @@
 			};
 
 			ldo1_reg: LDO1 {
-				regulator-name = "LDO1";
+				regulator-name = "ldo1";
 				regulator-min-microvolt = <1600000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
@@ -120,7 +120,7 @@
 			};
 
 			ldo2_reg: LDO2 {
-				regulator-name = "LDO2";
+				regulator-name = "ldo2";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <900000>;
 				regulator-boot-on;
@@ -128,7 +128,7 @@
 			};
 
 			ldo3_reg: LDO3 {
-				regulator-name = "LDO3";
+				regulator-name = "ldo3";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
@@ -136,7 +136,7 @@
 			};
 
 			ldo4_reg: LDO4 {
-				regulator-name = "LDO4";
+				regulator-name = "ldo4";
 				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-boot-on;
@@ -144,7 +144,7 @@
 			};
 
 			ldo6_reg: LDO6 {
-				regulator-name = "LDO6";
+				regulator-name = "ldo6";
 				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-boot-on;
-- 
2.17.1

[PATCH v2 12/19] arm64: dts: imx8mn-evk: Align pin configuration group names with schema

[Krzysztof Kozlowski]

Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:

    ... do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi
index 48892ed562b4..ed9b5241acc7 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi
@@ -221,13 +221,13 @@
 		>;
 	};
 
-	pinctrl_pmic: pmicirq {
+	pinctrl_pmic: pmicirqgrp {
 		fsl,pins = <
 			MX8MN_IOMUXC_GPIO1_IO03_GPIO1_IO3	0x41
 		>;
 	};
 
-	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
+	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
 		fsl,pins = <
 			MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19	0x41
 		>;
@@ -246,7 +246,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_gpio: usdhc2grpgpio {
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
 		fsl,pins = <
 			MX8MN_IOMUXC_GPIO1_IO15_GPIO1_IO15	0x1c4
 		>;
@@ -264,7 +264,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
 		fsl,pins = <
 			MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK		0x194
 			MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4
@@ -276,7 +276,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 		fsl,pins = <
 			MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK		0x196
 			MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d6
@@ -304,7 +304,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
 		fsl,pins = <
 			MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK		0x40000194
 			MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d4
@@ -320,7 +320,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
 		fsl,pins = <
 			MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK		0x40000196
 			MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d6
-- 
2.17.1

[PATCH v2 13/19] arm64: dts: imx8mq-evk: Align pin configuration group names with schema

[Krzysztof Kozlowski]

Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:

    ... do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8mq-evk.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
index a088831d2e24..7c6808814856 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
@@ -407,7 +407,7 @@
 		>;
 	};
 
-	pinctrl_reg_usdhc2: regusdhc2grpgpio {
+	pinctrl_reg_usdhc2: regusdhc2gpiogrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD2_RESET_B_GPIO2_IO19		0x41
 		>;
-- 
2.17.1

[PATCH v2 14/19] arm64: dts: imx8mq-librem5-devkit: Align pin configuration group names with schema

[Krzysztof Kozlowski]

Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:

    ... do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 .../boot/dts/freescale/imx8mq-librem5-devkit.dts     | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
index 6900ac274f5b..377591a0e6e9 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
@@ -734,7 +734,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x8d
 			MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xcd
@@ -751,7 +751,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x9f
 			MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xdf
@@ -768,13 +768,13 @@
 		>;
 	};
 
-	pinctrl_usdhc2_pwr: usdhc2grppwr {
+	pinctrl_usdhc2_pwr: usdhc2pwrgrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD2_RESET_B_GPIO2_IO19	0x41
 		>;
 	};
 
-	pinctrl_usdhc2_gpio: usdhc2grpgpio {
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD2_WP_GPIO2_IO20		0x80 /* WIFI_WAKE */
 		>;
@@ -791,7 +791,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK		0x8d
 			MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD		0xcd
@@ -802,7 +802,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK		0x9f
 			MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD		0xcf
-- 
2.17.1

[PATCH v2 15/19] arm64: dts: imx8mq-phanbell: Align pin configuration group names with schema

[Krzysztof Kozlowski]

Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:

    ... do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8mq-phanbell.dts | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-phanbell.dts b/arch/arm64/boot/dts/freescale/imx8mq-phanbell.dts
index 3f541ddf0768..d6d3a3d5abc3 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-phanbell.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-phanbell.dts
@@ -365,7 +365,7 @@
 		>;
 	};
 
-	pinctrl_pmic: pmicirq {
+	pinctrl_pmic: pmicirqgrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_GPIO1_IO03_GPIO1_IO3	0x41
 		>;
@@ -395,7 +395,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x85
 			MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xc5
@@ -412,7 +412,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x87
 			MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xc7
@@ -429,7 +429,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_gpio: usdhc2grpgpio {
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12	0x41
 			MX8MQ_IOMUXC_SD2_RESET_B_GPIO2_IO19	0x41
@@ -448,7 +448,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x85
 			MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xc5
@@ -460,7 +460,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x87
 			MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xc7
-- 
2.17.1

[PATCH v2 16/19] arm64: dts: imx8mq-pico-pi: Align pin configuration group names with schema

[Krzysztof Kozlowski]

Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:

    ... do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts b/arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts
index 59da96b7143f..f4d5748a7bd6 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts
@@ -297,7 +297,7 @@
 		>;
 	};
 
-	pinctrl_pmic: pmicirq {
+	pinctrl_pmic: pmicirqgrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_GPIO1_IO03_GPIO1_IO3	0x41
 		>;
@@ -335,7 +335,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x85
 			MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xc5
@@ -351,7 +351,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x87
 			MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xc7
@@ -367,7 +367,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_gpio: usdhc2grpgpio {
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12	0x41
 		>;
@@ -385,7 +385,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x85
 			MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xc5
@@ -397,7 +397,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x87
 			MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xc7
-- 
2.17.1

[PATCH v2 17/19] arm64: dts: imx8mq-sr-som: Align pin configuration group names with schema

[Krzysztof Kozlowski]

Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:

    ... do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8mq-sr-som.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-sr-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-sr-som.dtsi
index 404c46671b96..0187890a90c5 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-sr-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq-sr-som.dtsi
@@ -275,7 +275,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x8d
 			MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xcd
@@ -292,7 +292,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x9f
 			MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xdf
-- 
2.17.1

[PATCH v2 18/19] arm64: dts: imx8mq-hummingboard-pulse: Align pin configuration group names with schema

[Krzysztof Kozlowski]

Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:

    ... do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 .../boot/dts/freescale/imx8mq-hummingboard-pulse.dts      | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-hummingboard-pulse.dts b/arch/arm64/boot/dts/freescale/imx8mq-hummingboard-pulse.dts
index bfd91c1ed6a5..366693f31992 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-hummingboard-pulse.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-hummingboard-pulse.dts
@@ -214,13 +214,13 @@
 		>;
 	};
 
-	pinctrl_usdhc2_gpio: usdhc2grpgpio {
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12	0x41
 		>;
 	};
 
-	pinctrl_usdhc2_vmmc: usdhc2vmmcgpio {
+	pinctrl_usdhc2_vmmc: usdhc2vmmcgpiogrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_GPIO1_IO13_GPIO1_IO13	0x41
 		>;
@@ -238,7 +238,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x8d
 			MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xcd
@@ -250,7 +250,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x9f
 			MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xdf
-- 
2.17.1

[PATCH v2 19/19] arm64: dts: imx8qxp-colibri: Align pin configuration group names with schema

[Krzysztof Kozlowski]

Device tree schema expects pin configuration groups to end with 'grp'
suffix, otherwise dtbs_check complain with a warning like:

    ... do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8qxp-colibri.dtsi | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-colibri.dtsi b/arch/arm64/boot/dts/freescale/imx8qxp-colibri.dtsi
index 75f17a29f81e..f38acff0d25c 100644
--- a/arch/arm64/boot/dts/freescale/imx8qxp-colibri.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8qxp-colibri.dtsi
@@ -494,7 +494,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
 		fsl,pins = <
 			IMX8QXP_EMMC0_CLK_CONN_EMMC0_CLK		0x06000041
 			IMX8QXP_EMMC0_CMD_CONN_EMMC0_CMD		0x21
@@ -511,7 +511,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
 		fsl,pins = <
 			IMX8QXP_EMMC0_CLK_CONN_EMMC0_CLK		0x06000041
 			IMX8QXP_EMMC0_CMD_CONN_EMMC0_CMD		0x21
@@ -554,7 +554,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
 		fsl,pins = <
 			IMX8QXP_USDHC1_CLK_CONN_USDHC1_CLK		0x06000041	/* SODIMM  47 */
 			IMX8QXP_USDHC1_CMD_CONN_USDHC1_CMD		0x21		/* SODIMM 190 */
@@ -566,7 +566,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 		fsl,pins = <
 			IMX8QXP_USDHC1_CLK_CONN_USDHC1_CLK		0x06000041	/* SODIMM  47 */
 			IMX8QXP_USDHC1_CMD_CONN_USDHC1_CMD		0x21		/* SODIMM 190 */
-- 
2.17.1

Re: [PATCH v2 11/19] arm64: dts: imx8mn-ddr4-evk: Align regulator names with schema

[Vaittinen, Matti]

On Fri, 2020-08-28 at 18:47 +0200, Krzysztof Kozlowski wrote:
> Device tree schema expects regulator names to be lowercase.  Changing
> to
> lowercase has multiple effects:
> 1. LDO6 supply is now properly configured, because regulator driver
>    looks for supplies by lowercase name,
> 2. User-visible names via sysfs or debugfs are now lowercase,
> 2. dtbs_check warnings are fixed:
> 
>     pmic@4b: regulators:LDO1:regulator-name:0: 'LDO1' does not match
> '^ldo[1-6]$'
> 
> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

FWIW:
Acked-By: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>

> ---
>  .../boot/dts/freescale/imx8mn-ddr4-evk.dts    | 22 +++++++++------
> ----
>  1 file changed, 11 insertions(+), 11 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
> b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
> index 3ac8f9d3c372..8f7155716c84 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
> @@ -60,7 +60,7 @@
>  
>  		regulators {
>  			buck1_reg: BUCK1 {
> -				regulator-name = "BUCK1";
> +				regulator-name = "buck1";
>  				regulator-min-microvolt = <700000>;
>  				regulator-max-microvolt = <1300000>;
>  				regulator-boot-on;
> @@ -69,7 +69,7 @@
>  			};
>  
>  			buck2_reg: BUCK2 {
> -				regulator-name = "BUCK2";
> +				regulator-name = "buck2";
>  				regulator-min-microvolt = <700000>;
>  				regulator-max-microvolt = <1300000>;
>  				regulator-boot-on;
> @@ -79,14 +79,14 @@
>  
>  			buck3_reg: BUCK3 {
>  				// BUCK5 in datasheet
> -				regulator-name = "BUCK3";
> +				regulator-name = "buck3";
>  				regulator-min-microvolt = <700000>;
>  				regulator-max-microvolt = <1350000>;
>  			};
>  
>  			buck4_reg: BUCK4 {
>  				// BUCK6 in datasheet
> -				regulator-name = "BUCK4";
> +				regulator-name = "buck4";
>  				regulator-min-microvolt = <3000000>;
>  				regulator-max-microvolt = <3300000>;
>  				regulator-boot-on;
> @@ -95,7 +95,7 @@
>  
>  			buck5_reg: BUCK5 {
>  				// BUCK7 in datasheet
> -				regulator-name = "BUCK5";
> +				regulator-name = "buck5";
>  				regulator-min-microvolt = <1605000>;
>  				regulator-max-microvolt = <1995000>;
>  				regulator-boot-on;
> @@ -104,7 +104,7 @@
>  
>  			buck6_reg: BUCK6 {
>  				// BUCK8 in datasheet
> -				regulator-name = "BUCK6";
> +				regulator-name = "buck6";
>  				regulator-min-microvolt = <800000>;
>  				regulator-max-microvolt = <1400000>;
>  				regulator-boot-on;
> @@ -112,7 +112,7 @@
>  			};
>  
>  			ldo1_reg: LDO1 {
> -				regulator-name = "LDO1";
> +				regulator-name = "ldo1";
>  				regulator-min-microvolt = <1600000>;
>  				regulator-max-microvolt = <3300000>;
>  				regulator-boot-on;
> @@ -120,7 +120,7 @@
>  			};
>  
>  			ldo2_reg: LDO2 {
> -				regulator-name = "LDO2";
> +				regulator-name = "ldo2";
>  				regulator-min-microvolt = <800000>;
>  				regulator-max-microvolt = <900000>;
>  				regulator-boot-on;
> @@ -128,7 +128,7 @@
>  			};
>  
>  			ldo3_reg: LDO3 {
> -				regulator-name = "LDO3";
> +				regulator-name = "ldo3";
>  				regulator-min-microvolt = <1800000>;
>  				regulator-max-microvolt = <3300000>;
>  				regulator-boot-on;
> @@ -136,7 +136,7 @@
>  			};
>  
>  			ldo4_reg: LDO4 {
> -				regulator-name = "LDO4";
> +				regulator-name = "ldo4";
>  				regulator-min-microvolt = <900000>;
>  				regulator-max-microvolt = <1800000>;
>  				regulator-boot-on;
> @@ -144,7 +144,7 @@
>  			};
>  
>  			ldo6_reg: LDO6 {
> -				regulator-name = "LDO6";
> +				regulator-name = "ldo6";
>  				regulator-min-microvolt = <900000>;
>  				regulator-max-microvolt = <1800000>;
>  				regulator-boot-on;

Re: [PATCH v2 08/19] arm64: dts: imx8mm-evk: Add 32.768 kHz clock to PMIC

[Vaittinen, Matti]

On Fri, 2020-08-28 at 18:47 +0200, Krzysztof Kozlowski wrote:
> The ROHM BD71847 PMIC has a 32.768 kHz clock.  Adding necessary
> parent
> allows to probe the bd718x7 clock driver fixing boot errors:
> 
>     bd718xx-clk bd71847-clk.1.auto: No parent clk found
>     bd718xx-clk: probe of bd71847-clk.1.auto failed with error -22
> 
> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

FWIW:
Acked-By: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>

> ---
>  arch/arm64/boot/dts/freescale/imx8mm-evk.dts | 4 ++++
>  1 file changed, 4 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
> b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
> index 3cb8b6bcb657..0115f07bbc9d 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
> @@ -149,6 +149,10 @@
>  		interrupts = <3 GPIO_ACTIVE_LOW>;
>  		rohm,reset-snvs-powered;
>  
> +		#clock-cells = <0>;
> +		clocks = <&osc_32k 0>;
> +		clock-output-names = "clk-32k-out";
> +
>  		regulators {
>  			buck1_reg: BUCK1 {
>  				regulator-name = "buck1";

Re: [PATCH v2 06/19] arm64: dts: imx8mm-beacon: Align pin configuration group names with schema

[Shawn Guo]

On Fri, Aug 28, 2020 at 06:47:37PM +0200, Krzysztof Kozlowski wrote:
> Device tree schema expects pin configuration groups to end with 'grp'
> suffix.  This fixes dtbs_check warnings like:
> 
>   pinctrl@30330000: 'pcal6414-gpio', 'pmicirq', 'usdhc1grp100mhz', 'usdhc1grp200mhz', 'usdhc1grpgpio',
>     'usdhc2grp100mhz', 'usdhc2grp200mhz', 'usdhc2grpgpio', 'usdhc3grp100mhz', 'usdhc3grp200mhz'
>     do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
> 
> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

Applied, thanks.

Re: [PATCH v2 08/19] arm64: dts: imx8mm-evk: Add 32.768 kHz clock to PMIC

[Shawn Guo]

On Fri, Aug 28, 2020 at 06:47:39PM +0200, Krzysztof Kozlowski wrote:
> The ROHM BD71847 PMIC has a 32.768 kHz clock.  Adding necessary parent
> allows to probe the bd718x7 clock driver fixing boot errors:
> 
>     bd718xx-clk bd71847-clk.1.auto: No parent clk found
>     bd718xx-clk: probe of bd71847-clk.1.auto failed with error -22
> 
> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

Applied, thanks.

Re: [PATCH v2 09/19] arm64: dts: imx8mm-evk: Align pin configuration group names with schema

[Shawn Guo]

On Fri, Aug 28, 2020 at 06:47:40PM +0200, Krzysztof Kozlowski wrote:
> Device tree schema expects pin configuration groups to end with 'grp'
> suffix, otherwise dtbs_check complain with a warning like:
> 
>     ... do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
> 
> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

Applied #9 ~ #19, thanks.