[PATCH v2 0/3] mainline Plymovent M2M board

[PATCH v2 0/3] mainline Plymovent M2M board

[Oleksij Rempel]

changes v2:
- fsl.yaml: reorder ply,plym2m
- imx6dl-plym2m.dts: use hyphen instead of underscore in phy-clock

Oleksij Rempel (3):
  dt-bindings: vendor-prefixes: Add an entry for Plymovent
  dt-bindings: arm: fsl: add Plymovent M2M board
  ARM: dts: add Plymovent M2M board

 .../devicetree/bindings/arm/fsl.yaml          |   1 +
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 arch/arm/boot/dts/Makefile                    |   1 +
 arch/arm/boot/dts/imx6dl-plym2m.dts           | 394 ++++++++++++++++++
 4 files changed, 398 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts

-- 
2.28.0

[PATCH v2 1/3] dt-bindings: vendor-prefixes: Add an entry for Plymovent

[Oleksij Rempel]

Add "ply" entry for Plymovent Group BV: https://www.plymovent.com/

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 2baee2c817c1..60b59ca04066 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -818,6 +818,8 @@ patternProperties:
     description: PLDA
   "^plx,.*":
     description: Broadcom Corporation (formerly PLX Technology)
+  "^ply,.*":
+    description: Plymovent Group BV
   "^pni,.*":
     description: PNI Sensor Corporation
   "^pocketbook,.*":
-- 
2.28.0

[PATCH v2 2/3] dt-bindings: arm: fsl: add Plymovent M2M board

[Oleksij Rempel]

Add Plymovent Group BV M2M iMX6dl based board

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 6da9d734cdb7..e94a455eeab9 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -174,6 +174,7 @@ properties:
               - fsl,imx6dl-sabreauto      # i.MX6 DualLite/Solo SABRE Automotive Board
               - fsl,imx6dl-sabresd        # i.MX6 DualLite SABRE Smart Device Board
               - kontron,imx6dl-samx6i     # Kontron i.MX6 Solo SMARC Module
+              - ply,plym2m                # Plymovent M2M board
               - prt,prtrvt                # Protonic RVT board
               - prt,prtvt7                # Protonic VT7 board
               - technexion,imx6dl-pico-dwarf   # TechNexion i.MX6DL Pico-Dwarf
-- 
2.28.0

[PATCH v2 3/3] ARM: dts: add Plymovent M2M board

[Oleksij Rempel]

Plymovent M2M is a control interface produced for the Plymovent filter
systems.

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/Makefile          |   1 +
 arch/arm/boot/dts/imx6dl-plym2m.dts | 394 ++++++++++++++++++++++++++++
 2 files changed, 395 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4572db3fa5ae..3c3811fd8613 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -455,6 +455,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6dl-pico-hobbit.dtb \
 	imx6dl-pico-nymph.dtb \
 	imx6dl-pico-pi.dtb \
+	imx6dl-plym2m.dtb \
 	imx6dl-prtrvt.dtb \
 	imx6dl-prtvt7.dtb \
 	imx6dl-rex-basic.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
new file mode 100644
index 000000000000..4f96e05aa03f
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
@@ -0,0 +1,394 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+// SPDX-FileCopyrightText: 2014 Protonic Holland
+// SPDX-FileCopyrightText: 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx6dl.dtsi"
+
+/ {
+	model = "Plymovent M2M board";
+	compatible = "ply,plym2m", "fsl,imx6dl";
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 500000 0>;
+		brightness-levels = <0 1000>;
+		num-interpolated-steps = <20>;
+		default-brightness-level = <19>;
+		power-supply = <&reg_12v0>;
+	};
+
+	display {
+		compatible = "fsl,imx-parallel-display";
+		pinctrl-0 = <&pinctrl_ipu1_disp>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			display_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-debug {
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	panel {
+		compatible = "edt,etm0700g0bdh6";
+		backlight = <&backlight>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
+	clk50m_phy: phy-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_12v0: regulator-12v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "12v0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	xceiver-supply = <&reg_5v0>;
+	status = "okay";
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rmii";
+	clocks = <&clks IMX6QDL_CLK_ENET>,
+		 <&clks IMX6QDL_CLK_ENET>,
+		 <&clk50m_phy>;
+	clock-names = "ipg", "ahb", "ptp";
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Microchip KSZ8081RNA PHY */
+		rgmii_phy: ethernet-phy@0 {
+			reg = <0>;
+			interrupts-extended = <&gpio5 23 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"CAN1_TERM", "SD1_CD", "", "", "", "", "", "",
+		"DEBUG_0", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "ECSPI2_SS0", "", "", "", "TSC_BUSY", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "ECSPI1_SS1", "TSC_PENIRQ", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "CAN1_SR", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "ETH_RESET", "ETH_INTRP",
+		"", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	/* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	temperature-sensor@70 {
+		compatible = "ti,tmp103";
+		reg = <0x70>;
+	};
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&display_in>;
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbphynop1 {
+	status = "disabled";
+};
+
+&usbphynop2 {
+	status = "disabled";
+};
+
+&usbotg {
+	phy_type = "utmi";
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	disable-wp;
+	cap-sd-highspeed;
+	no-mmc;
+	no-sdio;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX		0x1b000
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX		0x3008
+			/* CAN1_SR */
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12			0x13008
+			/* CAN1_TERM */
+			MX6QDL_PAD_GPIO_0__GPIO1_IO00			0x1b088
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO			0x1b000
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI			0x3008
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK			0x3008
+			/* CS */
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19			0x3008
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			/* MX6QDL_ENET_PINGRP4 */
+			MX6QDL_PAD_ENET_MDC__ENET_MDC			0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO			0x1b0b0
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER		0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN		0x1b0b0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN		0x1b0b0
+
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK		0x1b0b0
+			/* Phy reset */
+			MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22		0x1b0b0
+			/* nINTRP */
+			MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23		0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA			0x4001f8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL			0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL			0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA			0x4001b8b1
+		>;
+	};
+
+	pinctrl_ipu1_disp: ipudisp1grp {
+		fsl,pins = <
+			/* DSE 0x30 => 25 Ohm, 0x20 => 37 Ohm, 0x10 => 75 Ohm */
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x30
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x30
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x30
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x30
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x30
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x30
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x30
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x30
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x30
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x30
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x30
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x30
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x30
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x30
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x30
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x30
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x30
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x30
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x30
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x30
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x30
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x30
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08			0x1b0b0
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__PWM1_OUT			0x8
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA		0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD			0x170f9
+			MX6QDL_PAD_SD1_CLK__SD1_CLK			0x100f9
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0			0x170f9
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1			0x170f9
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2			0x170f9
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3			0x170f9
+			MX6QDL_PAD_GPIO_1__GPIO1_IO01			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD			0x17099
+			MX6QDL_PAD_SD3_CLK__SD3_CLK			0x10099
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0			0x17099
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1			0x17099
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2			0x17099
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3			0x17099
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4			0x17099
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5			0x17099
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6			0x17099
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7			0x17099
+			MX6QDL_PAD_SD3_RST__SD3_RESET			0x1b0b1
+		>;
+	};
+};
-- 
2.28.0

Re: [PATCH v2 3/3] ARM: dts: add Plymovent M2M board

[Marco Felsch]

On 20-09-11 07:09, Oleksij Rempel wrote:
> Plymovent M2M is a control interface produced for the Plymovent filter
> systems.
> 
> Signed-off-by: David Jander <david@protonic.nl>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  arch/arm/boot/dts/Makefile          |   1 +
>  arch/arm/boot/dts/imx6dl-plym2m.dts | 394 ++++++++++++++++++++++++++++
>  2 files changed, 395 insertions(+)
>  create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 4572db3fa5ae..3c3811fd8613 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -455,6 +455,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
>  	imx6dl-pico-hobbit.dtb \
>  	imx6dl-pico-nymph.dtb \
>  	imx6dl-pico-pi.dtb \
> +	imx6dl-plym2m.dtb \
>  	imx6dl-prtrvt.dtb \
>  	imx6dl-prtvt7.dtb \
>  	imx6dl-rex-basic.dtb \
> diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
> new file mode 100644
> index 000000000000..4f96e05aa03f
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
> @@ -0,0 +1,394 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +// SPDX-FileCopyrightText: 2014 Protonic Holland
> +// SPDX-FileCopyrightText: 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
		^
@shawn: I saw a few patches adding these tags. Are they used in the near
future?

Regards,
  Marco

Re: [PATCH v2 3/3] ARM: dts: add Plymovent M2M board

[Shawn Guo]

On Fri, Sep 11, 2020 at 08:03:12AM +0200, Marco Felsch wrote:
> On 20-09-11 07:09, Oleksij Rempel wrote:
> > Plymovent M2M is a control interface produced for the Plymovent filter
> > systems.
> > 
> > Signed-off-by: David Jander <david@protonic.nl>
> > Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> > ---
> >  arch/arm/boot/dts/Makefile          |   1 +
> >  arch/arm/boot/dts/imx6dl-plym2m.dts | 394 ++++++++++++++++++++++++++++
> >  2 files changed, 395 insertions(+)
> >  create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts
> > 
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index 4572db3fa5ae..3c3811fd8613 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -455,6 +455,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> >  	imx6dl-pico-hobbit.dtb \
> >  	imx6dl-pico-nymph.dtb \
> >  	imx6dl-pico-pi.dtb \
> > +	imx6dl-plym2m.dtb \
> >  	imx6dl-prtrvt.dtb \
> >  	imx6dl-prtvt7.dtb \
> >  	imx6dl-rex-basic.dtb \
> > diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
> > new file mode 100644
> > index 000000000000..4f96e05aa03f
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
> > @@ -0,0 +1,394 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> > +// SPDX-FileCopyrightText: 2014 Protonic Holland
> > +// SPDX-FileCopyrightText: 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
> 		^
> @shawn: I saw a few patches adding these tags. Are they used in the near
> future?

I'm not sure.  I haven't seen this in Documentation/process/license-rules.rst,
nor the discussion around this.

Shawn

Re: [PATCH v2 3/3] ARM: dts: add Plymovent M2M board

[Oleksij Rempel]

On Sun, Sep 13, 2020 at 12:49:45PM +0800, Shawn Guo wrote:
> On Fri, Sep 11, 2020 at 08:03:12AM +0200, Marco Felsch wrote:
> > On 20-09-11 07:09, Oleksij Rempel wrote:
> > > Plymovent M2M is a control interface produced for the Plymovent filter
> > > systems.
> > > 
> > > Signed-off-by: David Jander <david@protonic.nl>
> > > Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> > > ---
> > >  arch/arm/boot/dts/Makefile          |   1 +
> > >  arch/arm/boot/dts/imx6dl-plym2m.dts | 394 ++++++++++++++++++++++++++++
> > >  2 files changed, 395 insertions(+)
> > >  create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts
> > > 
> > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > > index 4572db3fa5ae..3c3811fd8613 100644
> > > --- a/arch/arm/boot/dts/Makefile
> > > +++ b/arch/arm/boot/dts/Makefile
> > > @@ -455,6 +455,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> > >  	imx6dl-pico-hobbit.dtb \
> > >  	imx6dl-pico-nymph.dtb \
> > >  	imx6dl-pico-pi.dtb \
> > > +	imx6dl-plym2m.dtb \
> > >  	imx6dl-prtrvt.dtb \
> > >  	imx6dl-prtvt7.dtb \
> > >  	imx6dl-rex-basic.dtb \
> > > diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
> > > new file mode 100644
> > > index 000000000000..4f96e05aa03f
> > > --- /dev/null
> > > +++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
> > > @@ -0,0 +1,394 @@
> > > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> > > +// SPDX-FileCopyrightText: 2014 Protonic Holland
> > > +// SPDX-FileCopyrightText: 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
> > 		^
> > @shawn: I saw a few patches adding these tags. Are they used in the near
> > future?
> 
> I'm not sure.  I haven't seen this in Documentation/process/license-rules.rst,
> nor the discussion around this.

Hi Shawn,

is it a  no go? Should I send a patch with old style copyright text?


Regards,
Oleksij
-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

Re: [PATCH v2 3/3] ARM: dts: add Plymovent M2M board

[Shawn Guo]

On Mon, Sep 21, 2020 at 07:23:13AM +0200, Oleksij Rempel wrote:
> On Sun, Sep 13, 2020 at 12:49:45PM +0800, Shawn Guo wrote:
> > On Fri, Sep 11, 2020 at 08:03:12AM +0200, Marco Felsch wrote:
> > > On 20-09-11 07:09, Oleksij Rempel wrote:
> > > > Plymovent M2M is a control interface produced for the Plymovent filter
> > > > systems.
> > > > 
> > > > Signed-off-by: David Jander <david@protonic.nl>
> > > > Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> > > > ---
> > > >  arch/arm/boot/dts/Makefile          |   1 +
> > > >  arch/arm/boot/dts/imx6dl-plym2m.dts | 394 ++++++++++++++++++++++++++++
> > > >  2 files changed, 395 insertions(+)
> > > >  create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts
> > > > 
> > > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > > > index 4572db3fa5ae..3c3811fd8613 100644
> > > > --- a/arch/arm/boot/dts/Makefile
> > > > +++ b/arch/arm/boot/dts/Makefile
> > > > @@ -455,6 +455,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> > > >  	imx6dl-pico-hobbit.dtb \
> > > >  	imx6dl-pico-nymph.dtb \
> > > >  	imx6dl-pico-pi.dtb \
> > > > +	imx6dl-plym2m.dtb \
> > > >  	imx6dl-prtrvt.dtb \
> > > >  	imx6dl-prtvt7.dtb \
> > > >  	imx6dl-rex-basic.dtb \
> > > > diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
> > > > new file mode 100644
> > > > index 000000000000..4f96e05aa03f
> > > > --- /dev/null
> > > > +++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
> > > > @@ -0,0 +1,394 @@
> > > > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> > > > +// SPDX-FileCopyrightText: 2014 Protonic Holland
> > > > +// SPDX-FileCopyrightText: 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
> > > 		^
> > > @shawn: I saw a few patches adding these tags. Are they used in the near
> > > future?
> > 
> > I'm not sure.  I haven't seen this in Documentation/process/license-rules.rst,
> > nor the discussion around this.
> 
> Hi Shawn,
> 
> is it a  no go? Should I send a patch with old style copyright text?

Yeah, I would rather stay with the existing style before there is a
clear direction to the new one.

Also the vendor-prefixes patch needs an ACK from Rob.

Shawn