* [PATCH v2 0/3] mainline Plymovent M2M board
@ 2020-09-11 5:09 Oleksij Rempel
2020-09-11 5:09 ` [PATCH v2 1/3] dt-bindings: vendor-prefixes: Add an entry for Plymovent Oleksij Rempel
` (2 more replies)
0 siblings, 3 replies; 8+ messages in thread
From: Oleksij Rempel @ 2020-09-11 5:09 UTC (permalink / raw)
To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo
Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel,
linux-kernel, NXP Linux Team, Pengutronix Kernel Team,
David Jander
changes v2:
- fsl.yaml: reorder ply,plym2m
- imx6dl-plym2m.dts: use hyphen instead of underscore in phy-clock
Oleksij Rempel (3):
dt-bindings: vendor-prefixes: Add an entry for Plymovent
dt-bindings: arm: fsl: add Plymovent M2M board
ARM: dts: add Plymovent M2M board
.../devicetree/bindings/arm/fsl.yaml | 1 +
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-plym2m.dts | 394 ++++++++++++++++++
4 files changed, 398 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts
--
2.28.0
^ permalink raw reply [flat|nested] 8+ messages in thread* [PATCH v2 1/3] dt-bindings: vendor-prefixes: Add an entry for Plymovent 2020-09-11 5:09 [PATCH v2 0/3] mainline Plymovent M2M board Oleksij Rempel @ 2020-09-11 5:09 ` Oleksij Rempel 2020-09-11 5:09 ` [PATCH v2 2/3] dt-bindings: arm: fsl: add Plymovent M2M board Oleksij Rempel 2020-09-11 5:09 ` [PATCH v2 3/3] ARM: dts: " Oleksij Rempel 2 siblings, 0 replies; 8+ messages in thread From: Oleksij Rempel @ 2020-09-11 5:09 UTC (permalink / raw) To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel, linux-kernel, NXP Linux Team, Pengutronix Kernel Team, David Jander Add "ply" entry for Plymovent Group BV: https://www.plymovent.com/ Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> --- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index 2baee2c817c1..60b59ca04066 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -818,6 +818,8 @@ patternProperties: description: PLDA "^plx,.*": description: Broadcom Corporation (formerly PLX Technology) + "^ply,.*": + description: Plymovent Group BV "^pni,.*": description: PNI Sensor Corporation "^pocketbook,.*": -- 2.28.0 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 2/3] dt-bindings: arm: fsl: add Plymovent M2M board 2020-09-11 5:09 [PATCH v2 0/3] mainline Plymovent M2M board Oleksij Rempel 2020-09-11 5:09 ` [PATCH v2 1/3] dt-bindings: vendor-prefixes: Add an entry for Plymovent Oleksij Rempel @ 2020-09-11 5:09 ` Oleksij Rempel 2020-09-11 5:09 ` [PATCH v2 3/3] ARM: dts: " Oleksij Rempel 2 siblings, 0 replies; 8+ messages in thread From: Oleksij Rempel @ 2020-09-11 5:09 UTC (permalink / raw) To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo Cc: Oleksij Rempel, devicetree, Fabio Estevam, linux-arm-kernel, linux-kernel, NXP Linux Team, Pengutronix Kernel Team, David Jander Add Plymovent Group BV M2M iMX6dl based board Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> --- Documentation/devicetree/bindings/arm/fsl.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index 6da9d734cdb7..e94a455eeab9 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -174,6 +174,7 @@ properties: - fsl,imx6dl-sabreauto # i.MX6 DualLite/Solo SABRE Automotive Board - fsl,imx6dl-sabresd # i.MX6 DualLite SABRE Smart Device Board - kontron,imx6dl-samx6i # Kontron i.MX6 Solo SMARC Module + - ply,plym2m # Plymovent M2M board - prt,prtrvt # Protonic RVT board - prt,prtvt7 # Protonic VT7 board - technexion,imx6dl-pico-dwarf # TechNexion i.MX6DL Pico-Dwarf -- 2.28.0 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 3/3] ARM: dts: add Plymovent M2M board 2020-09-11 5:09 [PATCH v2 0/3] mainline Plymovent M2M board Oleksij Rempel 2020-09-11 5:09 ` [PATCH v2 1/3] dt-bindings: vendor-prefixes: Add an entry for Plymovent Oleksij Rempel 2020-09-11 5:09 ` [PATCH v2 2/3] dt-bindings: arm: fsl: add Plymovent M2M board Oleksij Rempel @ 2020-09-11 5:09 ` Oleksij Rempel 2020-09-11 6:03 ` Marco Felsch 2 siblings, 1 reply; 8+ messages in thread From: Oleksij Rempel @ 2020-09-11 5:09 UTC (permalink / raw) To: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo Cc: Oleksij Rempel, David Jander, devicetree, Fabio Estevam, linux-arm-kernel, linux-kernel, NXP Linux Team, Pengutronix Kernel Team Plymovent M2M is a control interface produced for the Plymovent filter systems. Signed-off-by: David Jander <david@protonic.nl> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx6dl-plym2m.dts | 394 ++++++++++++++++++++++++++++ 2 files changed, 395 insertions(+) create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 4572db3fa5ae..3c3811fd8613 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -455,6 +455,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-pico-hobbit.dtb \ imx6dl-pico-nymph.dtb \ imx6dl-pico-pi.dtb \ + imx6dl-plym2m.dtb \ imx6dl-prtrvt.dtb \ imx6dl-prtvt7.dtb \ imx6dl-rex-basic.dtb \ diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts new file mode 100644 index 000000000000..4f96e05aa03f --- /dev/null +++ b/arch/arm/boot/dts/imx6dl-plym2m.dts @@ -0,0 +1,394 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +// SPDX-FileCopyrightText: 2014 Protonic Holland +// SPDX-FileCopyrightText: 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix + +/dts-v1/; +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> +#include "imx6dl.dtsi" + +/ { + model = "Plymovent M2M board"; + compatible = "ply,plym2m", "fsl,imx6dl"; + + chosen { + stdout-path = &uart4; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 500000 0>; + brightness-levels = <0 1000>; + num-interpolated-steps = <20>; + default-brightness-level = <19>; + power-supply = <®_12v0>; + }; + + display { + compatible = "fsl,imx-parallel-display"; + pinctrl-0 = <&pinctrl_ipu1_disp>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + display_in: endpoint { + remote-endpoint = <&ipu1_di0_disp0>; + }; + }; + + port@1 { + reg = <1>; + + display_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds>; + + led-debug { + function = LED_FUNCTION_STATUS; + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; + + panel { + compatible = "edt,etm0700g0bdh6"; + backlight = <&backlight>; + power-supply = <®_3v3>; + + port { + panel_in: endpoint { + remote-endpoint = <&display_out>; + }; + }; + }; + + clk50m_phy: phy-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <50000000>; + }; + + reg_3v3: regulator-3v3 { + compatible = "regulator-fixed"; + regulator-name = "3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + reg_5v0: regulator-5v0 { + compatible = "regulator-fixed"; + regulator-name = "5v0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + reg_12v0: regulator-12v0 { + compatible = "regulator-fixed"; + regulator-name = "12v0"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + }; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can1>; + xceiver-supply = <®_5v0>; + status = "okay"; +}; + +&ecspi1 { + cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <20000000>; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rmii"; + clocks = <&clks IMX6QDL_CLK_ENET>, + <&clks IMX6QDL_CLK_ENET>, + <&clk50m_phy>; + clock-names = "ipg", "ahb", "ptp"; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + /* Microchip KSZ8081RNA PHY */ + rgmii_phy: ethernet-phy@0 { + reg = <0>; + interrupts-extended = <&gpio5 23 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>; + reset-assert-us = <10000>; + reset-deassert-us = <300>; + }; + }; +}; + +&gpio1 { + gpio-line-names = + "CAN1_TERM", "SD1_CD", "", "", "", "", "", "", + "DEBUG_0", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", ""; +}; + +&gpio2 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "ECSPI2_SS0", "", "", "", "TSC_BUSY", ""; +}; + +&gpio3 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "ECSPI1_SS1", "TSC_PENIRQ", "", "", "", + "", "", "", "", "", "", "", ""; +}; + +&gpio4 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "", "", "", "", "CAN1_SR", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", ""; +}; + +&gpio5 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "ETH_RESET", "ETH_INTRP", + "", "", "", "", "", "", "", ""; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + /* additional i2c devices are added automatically by the boot loader */ +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + temperature-sensor@70 { + compatible = "ti,tmp103"; + reg = <0x70>; + }; +}; + +&ipu1_di0_disp0 { + remote-endpoint = <&display_in>; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +&usbphynop1 { + status = "disabled"; +}; + +&usbphynop2 { + status = "disabled"; +}; + +&usbotg { + phy_type = "utmi"; + dr_mode = "host"; + disable-over-current; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; + no-1-8-v; + disable-wp; + cap-sd-highspeed; + no-mmc; + no-sdio; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3>; + bus-width = <8>; + no-1-8-v; + non-removable; + no-sd; + no-sdio; + status = "okay"; +}; + +&iomuxc { + pinctrl_can1: can1grp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000 + MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008 + /* CAN1_SR */ + MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008 + /* CAN1_TERM */ + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b088 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x1b000 + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x3008 + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x3008 + /* CS */ + MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x3008 + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + /* MX6QDL_ENET_PINGRP4 */ + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0 + MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0 + MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0 + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0 + MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0 + MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0 + MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0 + + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0 + /* Phy reset */ + MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0 + /* nINTRP */ + MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1 + MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 + >; + }; + + pinctrl_ipu1_disp: ipudisp1grp { + fsl,pins = < + /* DSE 0x30 => 25 Ohm, 0x20 => 37 Ohm, 0x10 => 75 Ohm */ + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x30 + MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x30 + MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x30 + MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x30 + MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x30 + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x30 + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x30 + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x30 + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x30 + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x30 + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x30 + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x30 + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x30 + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x30 + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x30 + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x30 + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x30 + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x30 + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x30 + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x30 + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x30 + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x30 + >; + }; + + pinctrl_leds: ledsgrp { + fsl,pins = < + MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0 + >; + }; + + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX6QDL_PAD_GPIO_9__PWM1_OUT 0x8 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9 + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9 + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9 + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9 + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9 + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9 + MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099 + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099 + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099 + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099 + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099 + MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1 + >; + }; +}; -- 2.28.0 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH v2 3/3] ARM: dts: add Plymovent M2M board 2020-09-11 5:09 ` [PATCH v2 3/3] ARM: dts: " Oleksij Rempel @ 2020-09-11 6:03 ` Marco Felsch 2020-09-13 4:49 ` Shawn Guo 0 siblings, 1 reply; 8+ messages in thread From: Marco Felsch @ 2020-09-11 6:03 UTC (permalink / raw) To: Oleksij Rempel Cc: Mark Rutland, Rob Herring, Sascha Hauer, Shawn Guo, devicetree, linux-kernel, NXP Linux Team, Pengutronix Kernel Team, David Jander, Fabio Estevam, linux-arm-kernel On 20-09-11 07:09, Oleksij Rempel wrote: > Plymovent M2M is a control interface produced for the Plymovent filter > systems. > > Signed-off-by: David Jander <david@protonic.nl> > Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/imx6dl-plym2m.dts | 394 ++++++++++++++++++++++++++++ > 2 files changed, 395 insertions(+) > create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 4572db3fa5ae..3c3811fd8613 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -455,6 +455,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ > imx6dl-pico-hobbit.dtb \ > imx6dl-pico-nymph.dtb \ > imx6dl-pico-pi.dtb \ > + imx6dl-plym2m.dtb \ > imx6dl-prtrvt.dtb \ > imx6dl-prtvt7.dtb \ > imx6dl-rex-basic.dtb \ > diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts > new file mode 100644 > index 000000000000..4f96e05aa03f > --- /dev/null > +++ b/arch/arm/boot/dts/imx6dl-plym2m.dts > @@ -0,0 +1,394 @@ > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT > +// SPDX-FileCopyrightText: 2014 Protonic Holland > +// SPDX-FileCopyrightText: 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix ^ @shawn: I saw a few patches adding these tags. Are they used in the near future? Regards, Marco ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v2 3/3] ARM: dts: add Plymovent M2M board 2020-09-11 6:03 ` Marco Felsch @ 2020-09-13 4:49 ` Shawn Guo 2020-09-21 5:23 ` Oleksij Rempel 0 siblings, 1 reply; 8+ messages in thread From: Shawn Guo @ 2020-09-13 4:49 UTC (permalink / raw) To: Marco Felsch Cc: Oleksij Rempel, Mark Rutland, Rob Herring, Sascha Hauer, devicetree, linux-kernel, NXP Linux Team, Pengutronix Kernel Team, David Jander, Fabio Estevam, linux-arm-kernel On Fri, Sep 11, 2020 at 08:03:12AM +0200, Marco Felsch wrote: > On 20-09-11 07:09, Oleksij Rempel wrote: > > Plymovent M2M is a control interface produced for the Plymovent filter > > systems. > > > > Signed-off-by: David Jander <david@protonic.nl> > > Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> > > --- > > arch/arm/boot/dts/Makefile | 1 + > > arch/arm/boot/dts/imx6dl-plym2m.dts | 394 ++++++++++++++++++++++++++++ > > 2 files changed, 395 insertions(+) > > create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts > > > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > > index 4572db3fa5ae..3c3811fd8613 100644 > > --- a/arch/arm/boot/dts/Makefile > > +++ b/arch/arm/boot/dts/Makefile > > @@ -455,6 +455,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ > > imx6dl-pico-hobbit.dtb \ > > imx6dl-pico-nymph.dtb \ > > imx6dl-pico-pi.dtb \ > > + imx6dl-plym2m.dtb \ > > imx6dl-prtrvt.dtb \ > > imx6dl-prtvt7.dtb \ > > imx6dl-rex-basic.dtb \ > > diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts > > new file mode 100644 > > index 000000000000..4f96e05aa03f > > --- /dev/null > > +++ b/arch/arm/boot/dts/imx6dl-plym2m.dts > > @@ -0,0 +1,394 @@ > > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT > > +// SPDX-FileCopyrightText: 2014 Protonic Holland > > +// SPDX-FileCopyrightText: 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix > ^ > @shawn: I saw a few patches adding these tags. Are they used in the near > future? I'm not sure. I haven't seen this in Documentation/process/license-rules.rst, nor the discussion around this. Shawn ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v2 3/3] ARM: dts: add Plymovent M2M board 2020-09-13 4:49 ` Shawn Guo @ 2020-09-21 5:23 ` Oleksij Rempel 2020-09-22 2:07 ` Shawn Guo 0 siblings, 1 reply; 8+ messages in thread From: Oleksij Rempel @ 2020-09-21 5:23 UTC (permalink / raw) To: Shawn Guo Cc: Marco Felsch, Mark Rutland, Rob Herring, Sascha Hauer, devicetree, linux-kernel, NXP Linux Team, Pengutronix Kernel Team, David Jander, Fabio Estevam, linux-arm-kernel On Sun, Sep 13, 2020 at 12:49:45PM +0800, Shawn Guo wrote: > On Fri, Sep 11, 2020 at 08:03:12AM +0200, Marco Felsch wrote: > > On 20-09-11 07:09, Oleksij Rempel wrote: > > > Plymovent M2M is a control interface produced for the Plymovent filter > > > systems. > > > > > > Signed-off-by: David Jander <david@protonic.nl> > > > Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> > > > --- > > > arch/arm/boot/dts/Makefile | 1 + > > > arch/arm/boot/dts/imx6dl-plym2m.dts | 394 ++++++++++++++++++++++++++++ > > > 2 files changed, 395 insertions(+) > > > create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts > > > > > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > > > index 4572db3fa5ae..3c3811fd8613 100644 > > > --- a/arch/arm/boot/dts/Makefile > > > +++ b/arch/arm/boot/dts/Makefile > > > @@ -455,6 +455,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ > > > imx6dl-pico-hobbit.dtb \ > > > imx6dl-pico-nymph.dtb \ > > > imx6dl-pico-pi.dtb \ > > > + imx6dl-plym2m.dtb \ > > > imx6dl-prtrvt.dtb \ > > > imx6dl-prtvt7.dtb \ > > > imx6dl-rex-basic.dtb \ > > > diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts > > > new file mode 100644 > > > index 000000000000..4f96e05aa03f > > > --- /dev/null > > > +++ b/arch/arm/boot/dts/imx6dl-plym2m.dts > > > @@ -0,0 +1,394 @@ > > > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT > > > +// SPDX-FileCopyrightText: 2014 Protonic Holland > > > +// SPDX-FileCopyrightText: 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix > > ^ > > @shawn: I saw a few patches adding these tags. Are they used in the near > > future? > > I'm not sure. I haven't seen this in Documentation/process/license-rules.rst, > nor the discussion around this. Hi Shawn, is it a no go? Should I send a patch with old style copyright text? Regards, Oleksij -- Pengutronix e.K. | | Steuerwalder Str. 21 | http://www.pengutronix.de/ | 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v2 3/3] ARM: dts: add Plymovent M2M board 2020-09-21 5:23 ` Oleksij Rempel @ 2020-09-22 2:07 ` Shawn Guo 0 siblings, 0 replies; 8+ messages in thread From: Shawn Guo @ 2020-09-22 2:07 UTC (permalink / raw) To: Oleksij Rempel Cc: Marco Felsch, Mark Rutland, Rob Herring, Sascha Hauer, devicetree, linux-kernel, NXP Linux Team, Pengutronix Kernel Team, David Jander, Fabio Estevam, linux-arm-kernel On Mon, Sep 21, 2020 at 07:23:13AM +0200, Oleksij Rempel wrote: > On Sun, Sep 13, 2020 at 12:49:45PM +0800, Shawn Guo wrote: > > On Fri, Sep 11, 2020 at 08:03:12AM +0200, Marco Felsch wrote: > > > On 20-09-11 07:09, Oleksij Rempel wrote: > > > > Plymovent M2M is a control interface produced for the Plymovent filter > > > > systems. > > > > > > > > Signed-off-by: David Jander <david@protonic.nl> > > > > Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> > > > > --- > > > > arch/arm/boot/dts/Makefile | 1 + > > > > arch/arm/boot/dts/imx6dl-plym2m.dts | 394 ++++++++++++++++++++++++++++ > > > > 2 files changed, 395 insertions(+) > > > > create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts > > > > > > > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > > > > index 4572db3fa5ae..3c3811fd8613 100644 > > > > --- a/arch/arm/boot/dts/Makefile > > > > +++ b/arch/arm/boot/dts/Makefile > > > > @@ -455,6 +455,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ > > > > imx6dl-pico-hobbit.dtb \ > > > > imx6dl-pico-nymph.dtb \ > > > > imx6dl-pico-pi.dtb \ > > > > + imx6dl-plym2m.dtb \ > > > > imx6dl-prtrvt.dtb \ > > > > imx6dl-prtvt7.dtb \ > > > > imx6dl-rex-basic.dtb \ > > > > diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts > > > > new file mode 100644 > > > > index 000000000000..4f96e05aa03f > > > > --- /dev/null > > > > +++ b/arch/arm/boot/dts/imx6dl-plym2m.dts > > > > @@ -0,0 +1,394 @@ > > > > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT > > > > +// SPDX-FileCopyrightText: 2014 Protonic Holland > > > > +// SPDX-FileCopyrightText: 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix > > > ^ > > > @shawn: I saw a few patches adding these tags. Are they used in the near > > > future? > > > > I'm not sure. I haven't seen this in Documentation/process/license-rules.rst, > > nor the discussion around this. > > Hi Shawn, > > is it a no go? Should I send a patch with old style copyright text? Yeah, I would rather stay with the existing style before there is a clear direction to the new one. Also the vendor-prefixes patch needs an ACK from Rob. Shawn ^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2020-09-22 2:07 UTC | newest] Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2020-09-11 5:09 [PATCH v2 0/3] mainline Plymovent M2M board Oleksij Rempel 2020-09-11 5:09 ` [PATCH v2 1/3] dt-bindings: vendor-prefixes: Add an entry for Plymovent Oleksij Rempel 2020-09-11 5:09 ` [PATCH v2 2/3] dt-bindings: arm: fsl: add Plymovent M2M board Oleksij Rempel 2020-09-11 5:09 ` [PATCH v2 3/3] ARM: dts: " Oleksij Rempel 2020-09-11 6:03 ` Marco Felsch 2020-09-13 4:49 ` Shawn Guo 2020-09-21 5:23 ` Oleksij Rempel 2020-09-22 2:07 ` Shawn Guo
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).