* [PATCH v2 net] net: stmmac: Modify configuration method of EEE timers
@ 2020-10-01 15:56 Voon Weifeng
2020-10-03 23:42 ` David Miller
0 siblings, 1 reply; 2+ messages in thread
From: Voon Weifeng @ 2020-10-01 15:56 UTC (permalink / raw)
To: David S . Miller, Maxime Coquelin
Cc: netdev, linux-kernel, Jose Abreu, Giuseppe Cavallaro,
Andrew Lunn, Alexandre Torgue, Ong Boon Leong, Voon Weifeng,
Seow Chen Yong, Mark Gross, Wong Vee Khee
From: "Vineetha G. Jaya Kumaran" <vineetha.g.jaya.kumaran@intel.com>
Ethtool manual stated that the tx-timer is the "the amount of time the
device should stay in idle mode prior to asserting its Tx LPI". The
previous implementation for "ethtool --set-eee tx-timer" sets the LPI TW
timer duration which is not correct. Hence, this patch fixes the
"ethtool --set-eee tx-timer" to configure the EEE LPI timer.
The LPI TW Timer will be using the defined default value instead of
"ethtool --set-eee tx-timer" which follows the EEE LS timer implementation.
Fixes: d765955d2ae0 ("stmmac: add the Energy Efficient Ethernet support")
Signed-off-by: Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Changelog V2
*Not removing/modifying the eee_timer.
*EEE LPI timer can be configured through ethtool and also the eee_timer
module param.
*EEE TW Timer will be configured with default value only, not able to be
configured through ethtool or module param. This follows the implementation
of the EEE LS Timer.
---
drivers/net/ethernet/stmicro/stmmac/stmmac.h | 2 ++
.../ethernet/stmicro/stmmac/stmmac_ethtool.c | 12 +++++++++-
.../net/ethernet/stmicro/stmmac/stmmac_main.c | 23 ++++++++++++-------
3 files changed, 28 insertions(+), 9 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
index 9c02fc754bf1..545696971f65 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
@@ -203,6 +203,8 @@ struct stmmac_priv {
int eee_enabled;
int eee_active;
int tx_lpi_timer;
+ int tx_lpi_enabled;
+ int eee_tw_timer;
unsigned int mode;
unsigned int chain_mode;
int extend_desc;
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
index 430a4b32ec1e..814879f91f76 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
@@ -665,6 +665,7 @@ static int stmmac_ethtool_op_get_eee(struct net_device *dev,
edata->eee_enabled = priv->eee_enabled;
edata->eee_active = priv->eee_active;
edata->tx_lpi_timer = priv->tx_lpi_timer;
+ edata->tx_lpi_enabled = priv->tx_lpi_enabled;
return phylink_ethtool_get_eee(priv->phylink, edata);
}
@@ -678,6 +679,10 @@ static int stmmac_ethtool_op_set_eee(struct net_device *dev,
if (!priv->dma_cap.eee)
return -EOPNOTSUPP;
+ if (priv->tx_lpi_enabled != edata->tx_lpi_enabled)
+ netdev_warn(priv->dev,
+ "Setting EEE tx-lpi is not supported\n");
+
if (!edata->eee_enabled)
stmmac_disable_eee_mode(priv);
@@ -685,7 +690,12 @@ static int stmmac_ethtool_op_set_eee(struct net_device *dev,
if (ret)
return ret;
- priv->tx_lpi_timer = edata->tx_lpi_timer;
+ if (edata->eee_enabled &&
+ priv->tx_lpi_timer != edata->tx_lpi_timer) {
+ priv->tx_lpi_timer = edata->tx_lpi_timer;
+ stmmac_eee_init(priv);
+ }
+
return 0;
}
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 89b2b3472852..b56b13d64ab4 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -94,7 +94,7 @@ static const u32 default_msg_level = (NETIF_MSG_DRV | NETIF_MSG_PROBE |
static int eee_timer = STMMAC_DEFAULT_LPI_TIMER;
module_param(eee_timer, int, 0644);
MODULE_PARM_DESC(eee_timer, "LPI tx expiration time in msec");
-#define STMMAC_LPI_T(x) (jiffies + msecs_to_jiffies(x))
+#define STMMAC_LPI_T(x) (jiffies + usecs_to_jiffies(x))
/* By default the driver will use the ring mode to manage tx and rx descriptors,
* but allow user to force to use the chain instead of the ring
@@ -370,7 +370,7 @@ static void stmmac_eee_ctrl_timer(struct timer_list *t)
struct stmmac_priv *priv = from_timer(priv, t, eee_ctrl_timer);
stmmac_enable_eee_mode(priv);
- mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(eee_timer));
+ mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(priv->tx_lpi_timer));
}
/**
@@ -383,7 +383,7 @@ static void stmmac_eee_ctrl_timer(struct timer_list *t)
*/
bool stmmac_eee_init(struct stmmac_priv *priv)
{
- int tx_lpi_timer = priv->tx_lpi_timer;
+ int eee_tw_timer = priv->eee_tw_timer;
/* Using PCS we cannot dial with the phy registers at this stage
* so we do not support extra feature like EEE.
@@ -403,7 +403,7 @@ bool stmmac_eee_init(struct stmmac_priv *priv)
if (priv->eee_enabled) {
netdev_dbg(priv->dev, "disable EEE\n");
del_timer_sync(&priv->eee_ctrl_timer);
- stmmac_set_eee_timer(priv, priv->hw, 0, tx_lpi_timer);
+ stmmac_set_eee_timer(priv, priv->hw, 0, eee_tw_timer);
}
mutex_unlock(&priv->lock);
return false;
@@ -411,11 +411,12 @@ bool stmmac_eee_init(struct stmmac_priv *priv)
if (priv->eee_active && !priv->eee_enabled) {
timer_setup(&priv->eee_ctrl_timer, stmmac_eee_ctrl_timer, 0);
- mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(eee_timer));
stmmac_set_eee_timer(priv, priv->hw, STMMAC_DEFAULT_LIT_LS,
- tx_lpi_timer);
+ eee_tw_timer);
}
+ mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(priv->tx_lpi_timer));
+
mutex_unlock(&priv->lock);
netdev_dbg(priv->dev, "Energy-Efficient Ethernet initialized\n");
return true;
@@ -930,6 +931,7 @@ static void stmmac_mac_link_down(struct phylink_config *config,
stmmac_mac_set(priv, priv->ioaddr, false);
priv->eee_active = false;
+ priv->tx_lpi_enabled = false;
stmmac_eee_init(priv);
stmmac_set_eee_pls(priv, priv->hw, false);
}
@@ -1027,6 +1029,7 @@ static void stmmac_mac_link_up(struct phylink_config *config,
if (phy && priv->dma_cap.eee) {
priv->eee_active = phy_init_eee(phy, 1) >= 0;
priv->eee_enabled = stmmac_eee_init(priv);
+ priv->tx_lpi_enabled = priv->eee_enabled;
stmmac_set_eee_pls(priv, priv->hw, true);
}
}
@@ -2061,7 +2064,7 @@ static int stmmac_tx_clean(struct stmmac_priv *priv, int budget, u32 queue)
if ((priv->eee_enabled) && (!priv->tx_path_in_lpi_mode)) {
stmmac_enable_eee_mode(priv);
- mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(eee_timer));
+ mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(priv->tx_lpi_timer));
}
/* We still have pending packets, let's call for a new scheduling */
@@ -2694,7 +2697,11 @@ static int stmmac_hw_setup(struct net_device *dev, bool init_ptp)
netdev_warn(priv->dev, "PTP init failed\n");
}
- priv->tx_lpi_timer = STMMAC_DEFAULT_TWT_LS;
+ priv->eee_tw_timer = STMMAC_DEFAULT_TWT_LS;
+
+ /* Convert the timer from msec to usec */
+ if (!priv->tx_lpi_timer)
+ priv->tx_lpi_timer = eee_timer * 1000;
if (priv->use_riwt) {
if (!priv->rx_riwt)
--
2.17.1
^ permalink raw reply related [flat|nested] 2+ messages in thread* Re: [PATCH v2 net] net: stmmac: Modify configuration method of EEE timers
2020-10-01 15:56 [PATCH v2 net] net: stmmac: Modify configuration method of EEE timers Voon Weifeng
@ 2020-10-03 23:42 ` David Miller
0 siblings, 0 replies; 2+ messages in thread
From: David Miller @ 2020-10-03 23:42 UTC (permalink / raw)
To: weifeng.voon
Cc: mcoquelin.stm32, netdev, linux-kernel, joabreu, peppe.cavallaro,
andrew, alexandre.torgue, boon.leong.ong, chen.yong.seow, mgross,
vee.khee.wong
From: Voon Weifeng <weifeng.voon@intel.com>
Date: Thu, 1 Oct 2020 23:56:09 +0800
> From: "Vineetha G. Jaya Kumaran" <vineetha.g.jaya.kumaran@intel.com>
>
> Ethtool manual stated that the tx-timer is the "the amount of time the
> device should stay in idle mode prior to asserting its Tx LPI". The
> previous implementation for "ethtool --set-eee tx-timer" sets the LPI TW
> timer duration which is not correct. Hence, this patch fixes the
> "ethtool --set-eee tx-timer" to configure the EEE LPI timer.
>
> The LPI TW Timer will be using the defined default value instead of
> "ethtool --set-eee tx-timer" which follows the EEE LS timer implementation.
>
> Fixes: d765955d2ae0 ("stmmac: add the Energy Efficient Ethernet support")
> Signed-off-by: Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
> Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
>
> Changelog V2
> *Not removing/modifying the eee_timer.
> *EEE LPI timer can be configured through ethtool and also the eee_timer
> module param.
> *EEE TW Timer will be configured with default value only, not able to be
> configured through ethtool or module param. This follows the implementation
> of the EEE LS Timer.
Please put the Changelog above the various signoffs and other tags, as those
should be at the end of the commit log message.
Just out of curiousity, where did you see put the changelog after the
tags, and thus caused you to use this layout? If you decided that on
your own, this is pretty much always a bad idea. Look to other
patches which have been accepted as a guide for how to format your commit
log message.
Applied, thank you.
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2020-10-03 23:42 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-10-01 15:56 [PATCH v2 net] net: stmmac: Modify configuration method of EEE timers Voon Weifeng
2020-10-03 23:42 ` David Miller
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).