Re: [PATCH v2 7/7] dt-bindings: adin1100: Add binding for ADIN1100 Ethernet PHY

[Oleksij Rempel <o.rempel@pengutronix.de>]

On Wed, Jul 28, 2021 at 11:23:12AM -0600, Rob Herring wrote:
> On Mon, Jul 26, 2021 at 11:53 PM Oleksij Rempel <o.rempel@pengutronix.de> wrote:
> >
> > On Mon, Jul 12, 2021 at 04:06:31PM +0300, alexandru.tachici@analog.com wrote:
> > > From: Alexandru Tachici <alexandru.tachici@analog.com>
> > >
> > > DT bindings for the ADIN1100 10BASE-T1L Ethernet PHY.
> > >
> > > Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
> > > ---
> > >  .../devicetree/bindings/net/adi,adin1100.yaml | 45 +++++++++++++++++++
> > >  1 file changed, 45 insertions(+)
> > >  create mode 100644 Documentation/devicetree/bindings/net/adi,adin1100.yaml
> > >
> > > diff --git a/Documentation/devicetree/bindings/net/adi,adin1100.yaml b/Documentation/devicetree/bindings/net/adi,adin1100.yaml
> > > new file mode 100644
> > > index 000000000000..14943164da7a
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/net/adi,adin1100.yaml
> > > @@ -0,0 +1,45 @@
> > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > > +%YAML 1.2
> > > +---
> > > +$id: http://devicetree.org/schemas/net/adi,adin1100.yaml#
> > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > +
> > > +title: Analog Devices ADIN1100 PHY
> > > +
> > > +maintainers:
> > > +  - Alexandru Tachici <alexandru.tachici@analog.com>
> > > +
> > > +description:
> > > +  Bindings for Analog Devices Industrial Low Power 10BASE-T1L Ethernet PHY
> > > +
> > > +allOf:
> > > +  - $ref: ethernet-phy.yaml#
> > > +
> > > +properties:
> > > +  adi,disable-2400mv-tx-level:
> > > +    description:
> > > +      Prevent ADIN1100 from using the 2.4 V pk-pk transmit level.
> > > +    type: boolean
> >
> > This property should be generic. It is defined by IEEE 802.3cg 2019 and can
> > be implemented on all T1L PHYs.
> >
> > I assume, it should be something like:
> > ethernet-phy-10base-t1l-2.4vpp-enable
> > ethernet-phy-10base-t1l-2.4vpp-disable
> 
> 'ethernet-phy-' is a bit redundant and I'd make it a tristate (not
> present, 0, 1). So just '10base-t1l-2.4vpp'?
> 
> > To overwrite bootstrapped of fuzed values if supported. The IEEE 802.3cg
> > specification uses following wordings for this functionality:
> > "10BASE-T1L increased transmit level request ..."

sounds ok for me.

Regards,
Oleksij
-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |