* [PATCH 0/6] Rongpin RP-H6B support (and support for GL850G)
@ 2022-11-27 7:31 Icenowy Zheng
2022-11-27 7:31 ` [PATCH 1/6] dt-bindings: vendor-prefixes: add Genesys Logic Icenowy Zheng
` (5 more replies)
0 siblings, 6 replies; 14+ messages in thread
From: Icenowy Zheng @ 2022-11-27 7:31 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Chen-Yu Tsai, Jernej Skrabec,
Samuel Holland, Greg Kroah-Hartman, Matthias Kaehlcke,
Andre Przywara
Cc: devicetree, linux-arm-kernel, linux-sunxi, linux-kernel,
linux-usb, Icenowy Zheng
This patchset adds support for Rongpin RP-H6B, and as a dependency,
power sequence support for its onboard USB hub, GL850G.
The first 3 patches are for GL850G, adding a binding for it and adding
its support to onboard_usb_hub driver.
The last 3 patches are for RP-H6B, also 2 for adding a binding and 1 for
the real DT.
Icenowy Zheng (6):
dt-bindings: vendor-prefixes: add Genesys Logic
dt-bindings: usb: Add binding for Genesys Logic GL850G hub controller
usb: misc: onboard_usb_hub: add Genesys Logic GL850G hub support
vendor-prefixes: Add Shenzhen Rongpin Electronics Co., Ltd
dt-bindings: arm: sunxi: add Rongpin RP-H6B board
arm64: dts: allwinner: h6: add Rongpin RP-H6C SoM and RP-H6B board
.../devicetree/bindings/arm/sunxi.yaml | 6 +
.../bindings/usb/genesys,gl850g.yaml | 48 ++++
.../devicetree/bindings/vendor-prefixes.yaml | 4 +
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h6-rp-h6b.dts | 239 ++++++++++++++++++
.../boot/dts/allwinner/sun50i-h6-rp-h6c.dtsi | 180 +++++++++++++
drivers/usb/misc/onboard_usb_hub.c | 2 +
drivers/usb/misc/onboard_usb_hub.h | 5 +
8 files changed, 485 insertions(+)
create mode 100644 Documentation/devicetree/bindings/usb/genesys,gl850g.yaml
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6b.dts
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6c.dtsi
--
2.37.1
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH 1/6] dt-bindings: vendor-prefixes: add Genesys Logic
2022-11-27 7:31 [PATCH 0/6] Rongpin RP-H6B support (and support for GL850G) Icenowy Zheng
@ 2022-11-27 7:31 ` Icenowy Zheng
2022-11-28 8:44 ` Krzysztof Kozlowski
2022-11-27 7:31 ` [PATCH 2/6] dt-bindings: usb: Add binding for Genesys Logic GL850G hub controller Icenowy Zheng
` (4 subsequent siblings)
5 siblings, 1 reply; 14+ messages in thread
From: Icenowy Zheng @ 2022-11-27 7:31 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Chen-Yu Tsai, Jernej Skrabec,
Samuel Holland, Greg Kroah-Hartman, Matthias Kaehlcke,
Andre Przywara
Cc: devicetree, linux-arm-kernel, linux-sunxi, linux-kernel,
linux-usb, Icenowy Zheng
Genesys Logic, Inc. is a manufacturer for interface chips, especially
USB hubs.
https://www.genesyslogic.com.tw/
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
---
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 6e323a380294..43359c0ccaf5 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -488,6 +488,8 @@ patternProperties:
description: GE Fanuc Intelligent Platforms Embedded Systems, Inc.
"^gemei,.*":
description: Gemei Digital Technology Co., Ltd.
+ "^genesys,.*":
+ description: Genesys Logic, Inc.
"^geniatech,.*":
description: Geniatech, Inc.
"^giantec,.*":
--
2.37.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 2/6] dt-bindings: usb: Add binding for Genesys Logic GL850G hub controller
2022-11-27 7:31 [PATCH 0/6] Rongpin RP-H6B support (and support for GL850G) Icenowy Zheng
2022-11-27 7:31 ` [PATCH 1/6] dt-bindings: vendor-prefixes: add Genesys Logic Icenowy Zheng
@ 2022-11-27 7:31 ` Icenowy Zheng
2022-11-27 16:25 ` Rob Herring
2022-11-28 8:47 ` Krzysztof Kozlowski
2022-11-27 7:31 ` [PATCH 3/6] usb: misc: onboard_usb_hub: add Genesys Logic GL850G hub support Icenowy Zheng
` (3 subsequent siblings)
5 siblings, 2 replies; 14+ messages in thread
From: Icenowy Zheng @ 2022-11-27 7:31 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Chen-Yu Tsai, Jernej Skrabec,
Samuel Holland, Greg Kroah-Hartman, Matthias Kaehlcke,
Andre Przywara
Cc: devicetree, linux-arm-kernel, linux-sunxi, linux-kernel,
linux-usb, Icenowy Zheng
The Genesys Logic GL850G is a USB 2.0 Single TT hub controller that
features 4 downstream ports, an internal 5V-to-3.3V LDO regulator (can
be bypassed) and an external reset pin.
Add a device tree binding for its USB protocol part. The internal LDO is
not covered by this and can just be modelled as a fixed regulator.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
---
.../bindings/usb/genesys,gl850g.yaml | 48 +++++++++++++++++++
1 file changed, 48 insertions(+)
create mode 100644 Documentation/devicetree/bindings/usb/genesys,gl850g.yaml
diff --git a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml
new file mode 100644
index 000000000000..d1fe539db399
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml
@@ -0,0 +1,48 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/realtek,rts5411.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Genesys Logic GL850G USB 2.0 hub controller
+
+maintainers:
+ - Icenowy Zheng <uwu@icenowy.me>
+
+allOf:
+ - $ref: usb-device.yaml#
+
+properties:
+ compatible:
+ items:
+ - enum:
+ - usb5e3,608
+
+ reg: true
+
+ reset-gpios:
+ description: GPIO specifier for GRST# pin.
+
+ vdd-supply:
+ description:
+ phandle to the regulator that provides power to the hub.
+
+required:
+ - compatible
+ - reg
+
+additionalProperties: false
+
+examples:
+ - |
+ usb {
+ dr_mode = "host";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hub: hub@1 {
+ compatible = "usb5e3,608";
+ reg = <1>;
+ reset-gpios = <&pio 7 2 GPIO_ACTIVE_LOW>;
+ };
+ };
--
2.37.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 3/6] usb: misc: onboard_usb_hub: add Genesys Logic GL850G hub support
2022-11-27 7:31 [PATCH 0/6] Rongpin RP-H6B support (and support for GL850G) Icenowy Zheng
2022-11-27 7:31 ` [PATCH 1/6] dt-bindings: vendor-prefixes: add Genesys Logic Icenowy Zheng
2022-11-27 7:31 ` [PATCH 2/6] dt-bindings: usb: Add binding for Genesys Logic GL850G hub controller Icenowy Zheng
@ 2022-11-27 7:31 ` Icenowy Zheng
2022-11-28 18:01 ` Matthias Kaehlcke
2022-11-27 7:31 ` [PATCH 4/6] vendor-prefixes: Add Shenzhen Rongpin Electronics Co., Ltd Icenowy Zheng
` (2 subsequent siblings)
5 siblings, 1 reply; 14+ messages in thread
From: Icenowy Zheng @ 2022-11-27 7:31 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Chen-Yu Tsai, Jernej Skrabec,
Samuel Holland, Greg Kroah-Hartman, Matthias Kaehlcke,
Andre Przywara
Cc: devicetree, linux-arm-kernel, linux-sunxi, linux-kernel,
linux-usb, Icenowy Zheng
This is a 4-port USB 2.0 STT hub.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
---
drivers/usb/misc/onboard_usb_hub.c | 2 ++
drivers/usb/misc/onboard_usb_hub.h | 5 +++++
2 files changed, 7 insertions(+)
diff --git a/drivers/usb/misc/onboard_usb_hub.c b/drivers/usb/misc/onboard_usb_hub.c
index d63c63942af1..f5c71d724be6 100644
--- a/drivers/usb/misc/onboard_usb_hub.c
+++ b/drivers/usb/misc/onboard_usb_hub.c
@@ -334,6 +334,7 @@ static struct platform_driver onboard_hub_driver = {
#define VENDOR_ID_MICROCHIP 0x0424
#define VENDOR_ID_REALTEK 0x0bda
#define VENDOR_ID_TI 0x0451
+#define VENDOR_ID_GENESYS 0x05e3
/*
* Returns the onboard_hub platform device that is associated with the USB
@@ -414,6 +415,7 @@ static const struct usb_device_id onboard_hub_id_table[] = {
{ USB_DEVICE(VENDOR_ID_REALTEK, 0x5414) }, /* RTS5414 USB 2.1 */
{ USB_DEVICE(VENDOR_ID_TI, 0x8140) }, /* TI USB8041 3.0 */
{ USB_DEVICE(VENDOR_ID_TI, 0x8142) }, /* TI USB8041 2.0 */
+ { USB_DEVICE(VENDOR_ID_GENESYS, 0x0608) }, /* Genesys Logic GL850G USB 2.0 */
{}
};
MODULE_DEVICE_TABLE(usb, onboard_hub_id_table);
diff --git a/drivers/usb/misc/onboard_usb_hub.h b/drivers/usb/misc/onboard_usb_hub.h
index 34beab8bce3d..1ca188713b1f 100644
--- a/drivers/usb/misc/onboard_usb_hub.h
+++ b/drivers/usb/misc/onboard_usb_hub.h
@@ -22,6 +22,10 @@ static const struct onboard_hub_pdata ti_tusb8041_data = {
.reset_us = 3000,
};
+static const struct onboard_hub_pdata genesys_gl850g_data = {
+ .reset_us = 3,
+};
+
static const struct of_device_id onboard_hub_match[] = {
{ .compatible = "usb424,2514", .data = µchip_usb424_data, },
{ .compatible = "usb451,8140", .data = &ti_tusb8041_data, },
@@ -30,6 +34,7 @@ static const struct of_device_id onboard_hub_match[] = {
{ .compatible = "usbbda,5411", .data = &realtek_rts5411_data, },
{ .compatible = "usbbda,414", .data = &realtek_rts5411_data, },
{ .compatible = "usbbda,5414", .data = &realtek_rts5411_data, },
+ { .compatible = "usb5e3,608", .data = &genesys_gl850g_data, },
{}
};
--
2.37.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 4/6] vendor-prefixes: Add Shenzhen Rongpin Electronics Co., Ltd
2022-11-27 7:31 [PATCH 0/6] Rongpin RP-H6B support (and support for GL850G) Icenowy Zheng
` (2 preceding siblings ...)
2022-11-27 7:31 ` [PATCH 3/6] usb: misc: onboard_usb_hub: add Genesys Logic GL850G hub support Icenowy Zheng
@ 2022-11-27 7:31 ` Icenowy Zheng
2022-11-28 8:47 ` Krzysztof Kozlowski
2022-11-27 7:31 ` [PATCH 5/6] dt-bindings: arm: sunxi: add Rongpin RP-H6B board Icenowy Zheng
2022-11-27 7:31 ` [PATCH 6/6] arm64: dts: allwinner: h6: add Rongpin RP-H6C SoM and " Icenowy Zheng
5 siblings, 1 reply; 14+ messages in thread
From: Icenowy Zheng @ 2022-11-27 7:31 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Chen-Yu Tsai, Jernej Skrabec,
Samuel Holland, Greg Kroah-Hartman, Matthias Kaehlcke,
Andre Przywara
Cc: devicetree, linux-arm-kernel, linux-sunxi, linux-kernel,
linux-usb, Icenowy Zheng
Add the vendor prefix for Shenzhen Rongpin Electronics Co., Ltd, which
specializes in ARM SoMs and EVBs.
Website: http://www.rpdzkj.com/
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
---
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 43359c0ccaf5..952ddeed4b4a 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -1091,6 +1091,8 @@ patternProperties:
description: ROHM Semiconductor Co., Ltd
"^ronbo,.*":
description: Ronbo Electronics
+ "^rongpin,.*":
+ description: Shenzhen Rongpin Electronics Co., Ltd
"^roofull,.*":
description: Shenzhen Roofull Technology Co, Ltd
"^roseapplepi,.*":
--
2.37.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 5/6] dt-bindings: arm: sunxi: add Rongpin RP-H6B board
2022-11-27 7:31 [PATCH 0/6] Rongpin RP-H6B support (and support for GL850G) Icenowy Zheng
` (3 preceding siblings ...)
2022-11-27 7:31 ` [PATCH 4/6] vendor-prefixes: Add Shenzhen Rongpin Electronics Co., Ltd Icenowy Zheng
@ 2022-11-27 7:31 ` Icenowy Zheng
2022-11-28 8:48 ` Krzysztof Kozlowski
2022-11-27 7:31 ` [PATCH 6/6] arm64: dts: allwinner: h6: add Rongpin RP-H6C SoM and " Icenowy Zheng
5 siblings, 1 reply; 14+ messages in thread
From: Icenowy Zheng @ 2022-11-27 7:31 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Chen-Yu Tsai, Jernej Skrabec,
Samuel Holland, Greg Kroah-Hartman, Matthias Kaehlcke,
Andre Przywara
Cc: devicetree, linux-arm-kernel, linux-sunxi, linux-kernel,
linux-usb, Icenowy Zheng
Rongpin RP-H6B is a development board with RP-H6C SoM, which uses an
Allwinner H6 SoC.
Add compatible strings for it, including the board-specific compatible
and the SoM compatible.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
---
Documentation/devicetree/bindings/arm/sunxi.yaml | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml
index 3ad1cd50e3fe..482631815f2f 100644
--- a/Documentation/devicetree/bindings/arm/sunxi.yaml
+++ b/Documentation/devicetree/bindings/arm/sunxi.yaml
@@ -792,6 +792,12 @@ properties:
- const: rervision,h3-dvk
- const: allwinner,sun8i-h3
+ - description: Rongpin RP-H6B development board
+ items:
+ - const: rongpin,rp-h6b
+ - const: rongpin,rp-h6c
+ - const: allwinner,sun50i-h6
+
- description: Sinlinx SinA31s Core Board
items:
- const: sinlinx,sina31s
--
2.37.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 6/6] arm64: dts: allwinner: h6: add Rongpin RP-H6C SoM and RP-H6B board
2022-11-27 7:31 [PATCH 0/6] Rongpin RP-H6B support (and support for GL850G) Icenowy Zheng
` (4 preceding siblings ...)
2022-11-27 7:31 ` [PATCH 5/6] dt-bindings: arm: sunxi: add Rongpin RP-H6B board Icenowy Zheng
@ 2022-11-27 7:31 ` Icenowy Zheng
2022-11-28 8:50 ` Krzysztof Kozlowski
5 siblings, 1 reply; 14+ messages in thread
From: Icenowy Zheng @ 2022-11-27 7:31 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Chen-Yu Tsai, Jernej Skrabec,
Samuel Holland, Greg Kroah-Hartman, Matthias Kaehlcke,
Andre Przywara
Cc: devicetree, linux-arm-kernel, linux-sunxi, linux-kernel,
linux-usb, Icenowy Zheng
Rongpin RP-H6C is an Allwinner H6 SoM by Rongpin, with Allwinner H6 SoC,
AXP805 PMIC, LPDDR3 memory and eMMC storage on it.
RP-H6B is their official evaluation board of RP-H6C, with an onboard
GL850G USB hub, Ampak AP6212 Wi-Fi module and some circuits about LVDS
display. It also exports the OTG USB port, the USB 3.0 port, PCIe bus
(as mPCIe slot), internal Ethernet PHY, analog audio/video and HDMI
port.
Add a DTSI file for the SoM and a DTS for the full board.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
---
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h6-rp-h6b.dts | 239 ++++++++++++++++++
.../boot/dts/allwinner/sun50i-h6-rp-h6c.dtsi | 180 +++++++++++++
3 files changed, 420 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6b.dts
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6c.dtsi
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 6a96494a2e0a..e289fedcac29 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -36,6 +36,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-lite2.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-rp-h6b.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6b.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6b.dts
new file mode 100644
index 000000000000..9fa40c365e63
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6b.dts
@@ -0,0 +1,239 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2022 Icenowy Zheng <icenowy@aosc.io>
+ */
+/dts-v1/;
+
+#include "sun50i-h6-rp-h6c.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Rongpin RP-H6B baseboard";
+ compatible = "rongpin,rp-h6b", "rongpin,rp-h6c",
+ "allwinner,sun50i-h6";
+
+ aliases {
+ ethernet0 = &emac;
+ serial0 = &uart0;
+ /*
+ * Prioritize the external RTC because it's powered
+ * by a cell battery.
+ */
+ rtc0 = &hym8563;
+ rtc1 = &rtc;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ hdmi_connector: connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led {
+ label = "rongpin:red:link";
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; /* PL3 */
+ /*
+ * On the schematics this LED is marked as "lit when
+ * powering on and blinking when running".
+ */
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ /*
+ * The VDD_5V power rail is connected to the internal regulator
+ * of GL850G, to power up the 3.3V core of it.
+ */
+ reg_v33_hub: v33-hub {
+ compatible = "regulator-fixed";
+ regulator-name = "v33-hub";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <®_vdd_5v>;
+ };
+
+ /*
+ * This board inputs 5V to AP6212 via a SS34 diode. Use this
+ * regulator as the model of the internal regulator of AP6212.
+ */
+ reg_vcc3v3_ap6212: vcc3v3-ap6212 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3-ap6212";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <®_ps>;
+ };
+
+ reg_vdd_5v: vdd-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ startup-delay-us = <100000>;
+ gpio = <&r_pio 0 5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <®_ps>;
+ };
+
+ /* For mPCIe slot WWAN modules / PCIe cards */
+ reg_vdd_3g: vdd-3g {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-3g";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ gpio = <&r_pio 0 7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <®_ps>;
+ /*
+ * As a hack for lacking of control of a hub downstream
+ * port's Vbus.
+ */
+ regulator-always-on;
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
+ post-power-on-delay-ms = <200>;
+ };
+};
+
+&de {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hub@1 {
+ /* Genesys Logic GL850G usb hub */
+ compatible = "usb5e3,608";
+ reg = <1>;
+ vdd-supply = <®_v33_hub>;
+ reset-gpios = <&pio 7 2 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&i2c0 {
+ status = "okay";
+
+ hym8563: rtc@51 {
+ compatible = "haoyu,hym8563";
+ reg = <0x51>;
+ #clock-cells = <0>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ vmmc-supply = <®_cldo1>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <®_vcc3v3_ap6212>;
+ vqmmc-supply = <®_bldo3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ non-removable;
+ bus-width = <4>;
+ status = "okay";
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&r_pio>;
+ interrupts = <1 0 IRQ_TYPE_LEVEL_LOW>; /* PM0 */
+ interrupt-names = "host-wake";
+ };
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+/* Converted from 12v with a fixed DC-DC on the baseboard */
+®_ps {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ph_pins>;
+ status = "okay";
+};
+
+/* Bluetooth */
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <1500000>;
+ clocks = <&rtc CLK_OSC32K_FANOUT>;
+ clock-names = "lpo";
+ vbat-supply = <®_ps>;
+ vddio-supply = <®_bldo3>;
+ device-wakeup-gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */
+ shutdown-gpios = <&r_pio 1 4 GPIO_ACTIVE_HIGH>; /* PM4 */
+ interrupt-parent = <&r_pio>;
+ interrupts = <1 1 IRQ_TYPE_EDGE_FALLING>; /* PM1 */
+ interrupt-names = "host-wakeup";
+ };
+};
+
+&uart1_pins {
+ bias-pull-up;
+};
+
+&uart1_rts_cts_pins {
+ bias-pull-up;
+};
+
+&usb2otg {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usb2phy {
+ usb0_vbus-supply = <®_vdd_5v>;
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6c.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6c.dtsi
new file mode 100644
index 000000000000..53822718e2d7
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6c.dtsi
@@ -0,0 +1,180 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2019-2022 Icenowy Zheng <icenowy@aosc.io>
+ */
+
+#include "sun50i-h6.dtsi"
+#include "sun50i-h6-cpu-opp.dtsi"
+#include "sun50i-h6-gpu-opp.dtsi"
+
+/ {
+ ext_osc32k: ext_osc32k_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "ext_osc32k";
+ };
+
+ /* Marked 3.4v~5.5v on SoM schematics */
+ reg_ps: ps {
+ compatible = "regulator-fixed";
+ regulator-name = "ps";
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdca>;
+};
+
+&gpu {
+ mali-supply = <®_dcdcc>;
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
+ vmmc-supply = <®_cldo1>;
+ vqmmc-supply = <®_bldo2>;
+ non-removable;
+ cap-mmc-hw-reset;
+ bus-width = <8>;
+ status = "okay";
+};
+
+&pio {
+ vcc-pc-supply = <®_bldo2>;
+ vcc-pd-supply = <®_aldo2>;
+ vcc-pg-supply = <®_bldo3>;
+};
+
+&r_pio {
+ /*
+ * FIXME: We can't add that supply for now since it would
+ * create a circular dependency between pinctrl, the regulator
+ * and the RSB Bus.
+ *
+ * vcc-pl-supply = <®_aldo1>;
+ */
+ vcc-pm-supply = <®_bldo3>;
+};
+
+&r_rsb {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ axp805: pmic@745 {
+ compatible = "x-powers,axp805", "x-powers,axp806";
+ reg = <0x745>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ x-powers,self-working-mode;
+ vina-supply = <®_ps>;
+ vinb-supply = <®_ps>;
+ vinc-supply = <®_ps>;
+ vind-supply = <®_ps>;
+ vine-supply = <®_ps>;
+ aldoin-supply = <®_ps>;
+ bldoin-supply = <®_ps>;
+ cldoin-supply = <®_ps>;
+
+ regulators {
+ reg_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pl";
+ };
+
+ reg_aldo2: aldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-ac200";
+ regulator-enable-ramp-delay = <100000>;
+ };
+
+ aldo3 {
+ /* unused */
+ };
+
+ reg_bldo1: bldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-bias-pll";
+ };
+
+ reg_bldo2: bldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-efuse-pcie-hdmi-io";
+ };
+
+ reg_bldo3: bldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-dcxoio";
+ };
+
+ bldo4 {
+ /* unused */
+ };
+
+ reg_cldo1: cldo1 {
+ /* This regulator is connected with ALDO3 */
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3-2";
+ };
+
+ cldo2 {
+ /* unused */
+ };
+
+ cldo3 {
+ /* unused */
+ };
+
+ reg_dcdca: dcdca {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1160000>;
+ regulator-ramp-delay = <2500>;
+ regulator-name = "vdd-cpu";
+ };
+
+ reg_dcdcc: dcdcc {
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1080000>;
+ regulator-name = "vdd-gpu";
+ };
+
+ reg_dcdcd: dcdcd {
+ regulator-always-on;
+ regulator-min-microvolt = <960000>;
+ regulator-max-microvolt = <960000>;
+ regulator-name = "vdd-sys";
+ };
+
+ reg_dcdce: dcdce {
+ regulator-always-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-dram";
+ };
+
+ sw {
+ /* unused */
+ };
+ };
+ };
+};
+
+&rtc {
+ clocks = <&ext_osc32k>;
+};
--
2.37.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH 2/6] dt-bindings: usb: Add binding for Genesys Logic GL850G hub controller
2022-11-27 7:31 ` [PATCH 2/6] dt-bindings: usb: Add binding for Genesys Logic GL850G hub controller Icenowy Zheng
@ 2022-11-27 16:25 ` Rob Herring
2022-11-28 8:47 ` Krzysztof Kozlowski
1 sibling, 0 replies; 14+ messages in thread
From: Rob Herring @ 2022-11-27 16:25 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Rob Herring, Jernej Skrabec, Samuel Holland, linux-kernel,
Andre Przywara, devicetree, linux-arm-kernel,
Krzysztof Kozlowski, Matthias Kaehlcke, linux-sunxi,
Greg Kroah-Hartman, Chen-Yu Tsai, linux-usb
On Sun, 27 Nov 2022 15:31:36 +0800, Icenowy Zheng wrote:
> The Genesys Logic GL850G is a USB 2.0 Single TT hub controller that
> features 4 downstream ports, an internal 5V-to-3.3V LDO regulator (can
> be bypassed) and an external reset pin.
>
> Add a device tree binding for its USB protocol part. The internal LDO is
> not covered by this and can just be modelled as a fixed regulator.
>
> Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
> ---
> .../bindings/usb/genesys,gl850g.yaml | 48 +++++++++++++++++++
> 1 file changed, 48 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/usb/genesys,gl850g.yaml
>
My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):
yamllint warnings/errors:
dtschema/dtc warnings/errors:
./Documentation/devicetree/bindings/usb/genesys,gl850g.yaml: $id: relative path/filename doesn't match actual path or filename
expected: http://devicetree.org/schemas/usb/genesys,gl850g.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/usb/realtek,rts5411.yaml: duplicate '$id' value 'http://devicetree.org/schemas/usb/realtek,rts5411.yaml#'
Error: Documentation/devicetree/bindings/usb/genesys,gl850g.example.dts:26.41-42 syntax error
FATAL ERROR: Unable to parse input tree
make[1]: *** [scripts/Makefile.lib:406: Documentation/devicetree/bindings/usb/genesys,gl850g.example.dtb] Error 1
make[1]: *** Waiting for unfinished jobs....
make: *** [Makefile:1492: dt_binding_check] Error 2
doc reference errors (make refcheckdocs):
See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20221127073140.2093897-3-uwu@icenowy.me
This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:
pip3 install dtschema --upgrade
Please check and re-submit after running the above command.
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 1/6] dt-bindings: vendor-prefixes: add Genesys Logic
2022-11-27 7:31 ` [PATCH 1/6] dt-bindings: vendor-prefixes: add Genesys Logic Icenowy Zheng
@ 2022-11-28 8:44 ` Krzysztof Kozlowski
0 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-11-28 8:44 UTC (permalink / raw)
To: Icenowy Zheng, Rob Herring, Krzysztof Kozlowski, Chen-Yu Tsai,
Jernej Skrabec, Samuel Holland, Greg Kroah-Hartman,
Matthias Kaehlcke, Andre Przywara
Cc: devicetree, linux-arm-kernel, linux-sunxi, linux-kernel, linux-usb
On 27/11/2022 08:31, Icenowy Zheng wrote:
> Genesys Logic, Inc. is a manufacturer for interface chips, especially
> USB hubs.
>
> https://www.genesyslogic.com.tw/
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 2/6] dt-bindings: usb: Add binding for Genesys Logic GL850G hub controller
2022-11-27 7:31 ` [PATCH 2/6] dt-bindings: usb: Add binding for Genesys Logic GL850G hub controller Icenowy Zheng
2022-11-27 16:25 ` Rob Herring
@ 2022-11-28 8:47 ` Krzysztof Kozlowski
1 sibling, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-11-28 8:47 UTC (permalink / raw)
To: Icenowy Zheng, Rob Herring, Krzysztof Kozlowski, Chen-Yu Tsai,
Jernej Skrabec, Samuel Holland, Greg Kroah-Hartman,
Matthias Kaehlcke, Andre Przywara
Cc: devicetree, linux-arm-kernel, linux-sunxi, linux-kernel, linux-usb
On 27/11/2022 08:31, Icenowy Zheng wrote:
> The Genesys Logic GL850G is a USB 2.0 Single TT hub controller that
> features 4 downstream ports, an internal 5V-to-3.3V LDO regulator (can
> be bypassed) and an external reset pin.
Subject: drop second, redundant "binding for".
Few nits below.
>
> Add a device tree binding for its USB protocol part. The internal LDO is
> not covered by this and can just be modelled as a fixed regulator.
>
> Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
> ---
> .../bindings/usb/genesys,gl850g.yaml | 48 +++++++++++++++++++
> 1 file changed, 48 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/usb/genesys,gl850g.yaml
>
> diff --git a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml
> new file mode 100644
> index 000000000000..d1fe539db399
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml
> @@ -0,0 +1,48 @@
> +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/usb/realtek,rts5411.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Genesys Logic GL850G USB 2.0 hub controller
> +
> +maintainers:
> + - Icenowy Zheng <uwu@icenowy.me>
> +
> +allOf:
> + - $ref: usb-device.yaml#
> +
> +properties:
> + compatible:
> + items:
Drop items, you have only one item.
> + - enum:
> + - usb5e3,608
> +
> + reg: true
> +
> + reset-gpios:
> + description: GPIO specifier for GRST# pin.
Drop "GPIO specifier for", so just "GRST# pin". No need to describe
DeviceTree syntax.
> +
> + vdd-supply:
> + description:
> + phandle to the regulator that provides power to the hub.
Also drop "phandle to"
> +
> +required:
> + - compatible
> + - reg
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + usb {
> + dr_mode = "host";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + hub: hub@1 {
> + compatible = "usb5e3,608";
> + reg = <1>;
> + reset-gpios = <&pio 7 2 GPIO_ACTIVE_LOW>;
Missing header.
Does not look like you tested the bindings. Please run `make
dt_binding_check` (see
Documentation/devicetree/bindings/writing-schema.rst for instructions).
> + };
> + };
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 4/6] vendor-prefixes: Add Shenzhen Rongpin Electronics Co., Ltd
2022-11-27 7:31 ` [PATCH 4/6] vendor-prefixes: Add Shenzhen Rongpin Electronics Co., Ltd Icenowy Zheng
@ 2022-11-28 8:47 ` Krzysztof Kozlowski
0 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-11-28 8:47 UTC (permalink / raw)
To: Icenowy Zheng, Rob Herring, Krzysztof Kozlowski, Chen-Yu Tsai,
Jernej Skrabec, Samuel Holland, Greg Kroah-Hartman,
Matthias Kaehlcke, Andre Przywara
Cc: devicetree, linux-arm-kernel, linux-sunxi, linux-kernel, linux-usb
On 27/11/2022 08:31, Icenowy Zheng wrote:
> Add the vendor prefix for Shenzhen Rongpin Electronics Co., Ltd, which
> specializes in ARM SoMs and EVBs.
>
> Website: http://www.rpdzkj.com/
>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 5/6] dt-bindings: arm: sunxi: add Rongpin RP-H6B board
2022-11-27 7:31 ` [PATCH 5/6] dt-bindings: arm: sunxi: add Rongpin RP-H6B board Icenowy Zheng
@ 2022-11-28 8:48 ` Krzysztof Kozlowski
0 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-11-28 8:48 UTC (permalink / raw)
To: Icenowy Zheng, Rob Herring, Krzysztof Kozlowski, Chen-Yu Tsai,
Jernej Skrabec, Samuel Holland, Greg Kroah-Hartman,
Matthias Kaehlcke, Andre Przywara
Cc: devicetree, linux-arm-kernel, linux-sunxi, linux-kernel, linux-usb
On 27/11/2022 08:31, Icenowy Zheng wrote:
> Rongpin RP-H6B is a development board with RP-H6C SoM, which uses an
> Allwinner H6 SoC.
>
> Add compatible strings for it, including the board-specific compatible
> and the SoM compatible.
>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 6/6] arm64: dts: allwinner: h6: add Rongpin RP-H6C SoM and RP-H6B board
2022-11-27 7:31 ` [PATCH 6/6] arm64: dts: allwinner: h6: add Rongpin RP-H6C SoM and " Icenowy Zheng
@ 2022-11-28 8:50 ` Krzysztof Kozlowski
0 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-11-28 8:50 UTC (permalink / raw)
To: Icenowy Zheng, Rob Herring, Krzysztof Kozlowski, Chen-Yu Tsai,
Jernej Skrabec, Samuel Holland, Greg Kroah-Hartman,
Matthias Kaehlcke, Andre Przywara
Cc: devicetree, linux-arm-kernel, linux-sunxi, linux-kernel, linux-usb
On 27/11/2022 08:31, Icenowy Zheng wrote:
> Rongpin RP-H6C is an Allwinner H6 SoM by Rongpin, with Allwinner H6 SoC,
> AXP805 PMIC, LPDDR3 memory and eMMC storage on it.
>
> RP-H6B is their official evaluation board of RP-H6C, with an onboard
> GL850G USB hub, Ampak AP6212 Wi-Fi module and some circuits about LVDS
> display. It also exports the OTG USB port, the USB 3.0 port, PCIe bus
> (as mPCIe slot), internal Ethernet PHY, analog audio/video and HDMI
> port.
>
> Add a DTSI file for the SoM and a DTS for the full board.
>
> Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
> ---
> arch/arm64/boot/dts/allwinner/Makefile | 1 +
> .../boot/dts/allwinner/sun50i-h6-rp-h6b.dts | 239 ++++++++++++++++++
> .../boot/dts/allwinner/sun50i-h6-rp-h6c.dtsi | 180 +++++++++++++
> 3 files changed, 420 insertions(+)
> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6b.dts
> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6c.dtsi
>
> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> index 6a96494a2e0a..e289fedcac29 100644
> --- a/arch/arm64/boot/dts/allwinner/Makefile
> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> @@ -36,6 +36,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-lite2.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-rp-h6b.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6b.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6b.dts
> new file mode 100644
> index 000000000000..9fa40c365e63
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6b.dts
> @@ -0,0 +1,239 @@
> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> +/*
> + * Copyright (C) 2022 Icenowy Zheng <icenowy@aosc.io>
> + */
> +/dts-v1/;
> +
> +#include "sun50i-h6-rp-h6c.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + model = "Rongpin RP-H6B baseboard";
> + compatible = "rongpin,rp-h6b", "rongpin,rp-h6c",
> + "allwinner,sun50i-h6";
> +
> + aliases {
> + ethernet0 = &emac;
> + serial0 = &uart0;
> + /*
> + * Prioritize the external RTC because it's powered
> + * by a cell battery.
> + */
> + rtc0 = &hym8563;
> + rtc1 = &rtc;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + hdmi_connector: connector {
> + compatible = "hdmi-connector";
> + type = "a";
> +
> + port {
> + hdmi_con_in: endpoint {
> + remote-endpoint = <&hdmi_out_con>;
> + };
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led {
> + label = "rongpin:red:link";
> + gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; /* PL3 */
> + /*
> + * On the schematics this LED is marked as "lit when
> + * powering on and blinking when running".
> + */
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + /*
> + * The VDD_5V power rail is connected to the internal regulator
> + * of GL850G, to power up the 3.3V core of it.
> + */
> + reg_v33_hub: v33-hub {
Node names should be generic, so at least generic "regulator" prefix or
suffix.
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
The same in further places.
> + compatible = "regulator-fixed";
> + regulator-name = "v33-hub";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <®_vdd_5v>;
> + };
> +
> + /*
> + * This board inputs 5V to AP6212 via a SS34 diode. Use this
> + * regulator as the model of the internal regulator of AP6212.
> + */
> + reg_vcc3v3_ap6212: vcc3v3-ap6212 {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc3v3-ap6212";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <®_ps>;
> + };
> +
> + reg_vdd_5v: vdd-5v {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd-5v";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + startup-delay-us = <100000>;
> + gpio = <&r_pio 0 5 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + vin-supply = <®_ps>;
> + };
> +
> + /* For mPCIe slot WWAN modules / PCIe cards */
> + reg_vdd_3g: vdd-3g {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd-3g";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + startup-delay-us = <100000>;
> + gpio = <&r_pio 0 7 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + vin-supply = <®_ps>;
> + /*
> + * As a hack for lacking of control of a hub downstream
> + * port's Vbus.
> + */
> + regulator-always-on;
> + };
> +
> + wifi_pwrseq: wifi_pwrseq {
No underscores in node names.
> + compatible = "mmc-pwrseq-simple";
> + reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
> + post-power-on-delay-ms = <200>;
> + };
> +};
> +
> +&de {
> + status = "okay";
> +};
> +
> +&ehci0 {
> + status = "okay";
> +};
> +
> +&ehci3 {
> + status = "okay";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + hub@1 {
> + /* Genesys Logic GL850G usb hub */
> + compatible = "usb5e3,608";
> + reg = <1>;
> + vdd-supply = <®_v33_hub>;
> + reset-gpios = <&pio 7 2 GPIO_ACTIVE_LOW>;
> + };
> +};
> +
> +&hdmi {
> + status = "okay";
> +};
> +
> +&hdmi_out {
> + hdmi_out_con: endpoint {
> + remote-endpoint = <&hdmi_con_in>;
> + };
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + hym8563: rtc@51 {
> + compatible = "haoyu,hym8563";
> + reg = <0x51>;
> + #clock-cells = <0>;
> + };
> +};
> +
> +&mmc0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_pins>;
> + vmmc-supply = <®_cldo1>;
> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
> + bus-width = <4>;
> + status = "okay";
> +};
> +
> +&mmc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc1_pins>;
> + vmmc-supply = <®_vcc3v3_ap6212>;
> + vqmmc-supply = <®_bldo3>;
> + mmc-pwrseq = <&wifi_pwrseq>;
> + non-removable;
> + bus-width = <4>;
> + status = "okay";
> +
> + brcmf: wifi@1 {
> + reg = <1>;
> + compatible = "brcm,bcm4329-fmac";
> + interrupt-parent = <&r_pio>;
> + interrupts = <1 0 IRQ_TYPE_LEVEL_LOW>; /* PM0 */
> + interrupt-names = "host-wake";
> + };
> +};
> +
> +&ohci0 {
> + status = "okay";
> +};
> +
> +/* Converted from 12v with a fixed DC-DC on the baseboard */
> +®_ps {
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_ph_pins>;
> + status = "okay";
> +};
> +
> +/* Bluetooth */
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
> + uart-has-rtscts;
> + status = "okay";
> +
> + bluetooth {
> + compatible = "brcm,bcm43438-bt";
> + max-speed = <1500000>;
> + clocks = <&rtc CLK_OSC32K_FANOUT>;
> + clock-names = "lpo";
> + vbat-supply = <®_ps>;
> + vddio-supply = <®_bldo3>;
> + device-wakeup-gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */
> + shutdown-gpios = <&r_pio 1 4 GPIO_ACTIVE_HIGH>; /* PM4 */
> + interrupt-parent = <&r_pio>;
> + interrupts = <1 1 IRQ_TYPE_EDGE_FALLING>; /* PM1 */
> + interrupt-names = "host-wakeup";
> + };
> +};
> +
> +&uart1_pins {
> + bias-pull-up;
> +};
> +
> +&uart1_rts_cts_pins {
> + bias-pull-up;
> +};
> +
> +&usb2otg {
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&usb2phy {
> + usb0_vbus-supply = <®_vdd_5v>;
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6c.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6c.dtsi
> new file mode 100644
> index 000000000000..53822718e2d7
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6c.dtsi
> @@ -0,0 +1,180 @@
> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> +/*
> + * Copyright (C) 2019-2022 Icenowy Zheng <icenowy@aosc.io>
> + */
> +
> +#include "sun50i-h6.dtsi"
> +#include "sun50i-h6-cpu-opp.dtsi"
> +#include "sun50i-h6-gpu-opp.dtsi"
> +
> +/ {
> + ext_osc32k: ext_osc32k_clk {
No underscores in node names.
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <32768>;
> + clock-output-names = "ext_osc32k";
> + };
> +
> + /* Marked 3.4v~5.5v on SoM schematics */
> + reg_ps: ps {
regulator prefix/suffix/etc
> + compatible = "regulator-fixed";
> + regulator-name = "ps";
> + };
> +};
> +
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 3/6] usb: misc: onboard_usb_hub: add Genesys Logic GL850G hub support
2022-11-27 7:31 ` [PATCH 3/6] usb: misc: onboard_usb_hub: add Genesys Logic GL850G hub support Icenowy Zheng
@ 2022-11-28 18:01 ` Matthias Kaehlcke
0 siblings, 0 replies; 14+ messages in thread
From: Matthias Kaehlcke @ 2022-11-28 18:01 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Rob Herring, Krzysztof Kozlowski, Chen-Yu Tsai, Jernej Skrabec,
Samuel Holland, Greg Kroah-Hartman, Andre Przywara, devicetree,
linux-arm-kernel, linux-sunxi, linux-kernel, linux-usb
On Sun, Nov 27, 2022 at 03:31:37PM +0800, Icenowy Zheng wrote:
> This is a 4-port USB 2.0 STT hub.
The commit message is supposed the describe the change, which
is almost certainly not a 4-port USB 2.0 STT hub :)
It could be something like "Add support for the Genesys Logic
GL850G, which is a 4-port USB 2.0 STT hub."
>
> Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
> ---
> drivers/usb/misc/onboard_usb_hub.c | 2 ++
> drivers/usb/misc/onboard_usb_hub.h | 5 +++++
> 2 files changed, 7 insertions(+)
>
> diff --git a/drivers/usb/misc/onboard_usb_hub.c b/drivers/usb/misc/onboard_usb_hub.c
> index d63c63942af1..f5c71d724be6 100644
> --- a/drivers/usb/misc/onboard_usb_hub.c
> +++ b/drivers/usb/misc/onboard_usb_hub.c
> @@ -334,6 +334,7 @@ static struct platform_driver onboard_hub_driver = {
> #define VENDOR_ID_MICROCHIP 0x0424
> #define VENDOR_ID_REALTEK 0x0bda
> #define VENDOR_ID_TI 0x0451
> +#define VENDOR_ID_GENESYS 0x05e3
Please insert the new entry in alphabetical order, i.e. before
VENDOR_ID_MICROCHIP.
>
> /*
> * Returns the onboard_hub platform device that is associated with the USB
> @@ -414,6 +415,7 @@ static const struct usb_device_id onboard_hub_id_table[] = {
> { USB_DEVICE(VENDOR_ID_REALTEK, 0x5414) }, /* RTS5414 USB 2.1 */
> { USB_DEVICE(VENDOR_ID_TI, 0x8140) }, /* TI USB8041 3.0 */
> { USB_DEVICE(VENDOR_ID_TI, 0x8142) }, /* TI USB8041 2.0 */
> + { USB_DEVICE(VENDOR_ID_GENESYS, 0x0608) }, /* Genesys Logic GL850G USB 2.0 */
Same here, the table is ordered alphabetically
> {}
> };
> MODULE_DEVICE_TABLE(usb, onboard_hub_id_table);
> diff --git a/drivers/usb/misc/onboard_usb_hub.h b/drivers/usb/misc/onboard_usb_hub.h
> index 34beab8bce3d..1ca188713b1f 100644
> --- a/drivers/usb/misc/onboard_usb_hub.h
> +++ b/drivers/usb/misc/onboard_usb_hub.h
> @@ -22,6 +22,10 @@ static const struct onboard_hub_pdata ti_tusb8041_data = {
> .reset_us = 3000,
> };
>
> +static const struct onboard_hub_pdata genesys_gl850g_data = {
> + .reset_us = 3,
> +};
> +
> static const struct of_device_id onboard_hub_match[] = {
> { .compatible = "usb424,2514", .data = µchip_usb424_data, },
> { .compatible = "usb451,8140", .data = &ti_tusb8041_data, },
> @@ -30,6 +34,7 @@ static const struct of_device_id onboard_hub_match[] = {
> { .compatible = "usbbda,5411", .data = &realtek_rts5411_data, },
> { .compatible = "usbbda,414", .data = &realtek_rts5411_data, },
> { .compatible = "usbbda,5414", .data = &realtek_rts5411_data, },
> + { .compatible = "usb5e3,608", .data = &genesys_gl850g_data, },
These table is ordered by compatible string, the new entry should be
inserted after "usb451,8142".
Thanks
m.
^ permalink raw reply [flat|nested] 14+ messages in thread
end of thread, other threads:[~2022-11-28 18:19 UTC | newest]
Thread overview: 14+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-11-27 7:31 [PATCH 0/6] Rongpin RP-H6B support (and support for GL850G) Icenowy Zheng
2022-11-27 7:31 ` [PATCH 1/6] dt-bindings: vendor-prefixes: add Genesys Logic Icenowy Zheng
2022-11-28 8:44 ` Krzysztof Kozlowski
2022-11-27 7:31 ` [PATCH 2/6] dt-bindings: usb: Add binding for Genesys Logic GL850G hub controller Icenowy Zheng
2022-11-27 16:25 ` Rob Herring
2022-11-28 8:47 ` Krzysztof Kozlowski
2022-11-27 7:31 ` [PATCH 3/6] usb: misc: onboard_usb_hub: add Genesys Logic GL850G hub support Icenowy Zheng
2022-11-28 18:01 ` Matthias Kaehlcke
2022-11-27 7:31 ` [PATCH 4/6] vendor-prefixes: Add Shenzhen Rongpin Electronics Co., Ltd Icenowy Zheng
2022-11-28 8:47 ` Krzysztof Kozlowski
2022-11-27 7:31 ` [PATCH 5/6] dt-bindings: arm: sunxi: add Rongpin RP-H6B board Icenowy Zheng
2022-11-28 8:48 ` Krzysztof Kozlowski
2022-11-27 7:31 ` [PATCH 6/6] arm64: dts: allwinner: h6: add Rongpin RP-H6C SoM and " Icenowy Zheng
2022-11-28 8:50 ` Krzysztof Kozlowski
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).