[PATCH v4 00/11] arm64: dts: qcom: Add more support to X1E80100 base dtsi, CRD and QCP boards

[PATCH v4 00/11] arm64: dts: qcom: Add more support to X1E80100 base dtsi, CRD and QCP boards

[Abel Vesa]

This patchset adds every node necessary for both the CRD and QCP to boot
with PCIe, USB and embedded DisplayPort.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
Changes in v4:
- After a discussion off-list, it was suggested by Bjorn to split in separate patches.
- Addressed all of Konrad's comments, except of the clock-names one for the mdss,
  which there is nothing to be done about as all non-v5 do clk_bulk_get_all.
- Added more support to QCP, to be more aligned with CRD (except touchscreen
  and keyboard)
- Added a patch to fix some LDOs supplies on QCP
- Link to v3: https://lore.kernel.org/r/20231215-x1e80100-dts-missing-nodes-v3-0-c4e8d186adf2@linaro.org

Changes in v3:
- Reword the commit messages
- Link to v2: https://lore.kernel.org/r/20231215-x1e80100-dts-missing-nodes-v2-0-5a6efc04d00c@linaro.org

Changes in v2:
- Reword both commits to make it more clear nodes that are being added
- Dropped comments from interrupt maps from pcie nodes
- Replace all 0x0 with 0 in all reg properties
- Moved on separate lines reg, reset and clock names
- Dropped the sram and cpucp nodes
- Dropped pmic glink node
- Reordered all new clock controller nodes based on address
- Dropped unnecessary indent from touchpad and keyboard TLMM nodes
- Link to v1: https://lore.kernel.org/r/20231212-x1e80100-dts-missing-nodes-v1-0-1472efec2b08@linaro.org

---
Abel Vesa (7):
      arm64: dts: qcom: x1e80100: Add TCSR node
      arm64: dts: qcom: x1e80100: Add USB nodes
      arm64: dts: qcom: x1e80100: Add PCIe nodes
      arm64: dts: qcom: x1e80100: Add display nodes
      arm64: dts: qcom: x1e80100-crd: Enable more support
      arm64: dts: qcom: x1e80100-qcp: Enable more support
      arm64: dts: qcom: x1e80100-qcp: Fix supplies for LDOs 3E and 2J

Sibi Sankar (4):
      arm64: dts: qcom: x1e80100: Add IPCC node
      arm64: dts: qcom: x1e80100: Add SMP2P nodes
      arm64: dts: qcom: x1e80100: Add QMP AOSS node
      arm64: dts: qcom: x1e80100: Add ADSP/CDSP remoteproc nodes

 arch/arm64/boot/dts/qcom/x1e80100-crd.dts |  222 +++++
 arch/arm64/boot/dts/qcom/x1e80100-qcp.dts |  175 +++-
 arch/arm64/boot/dts/qcom/x1e80100.dtsi    | 1349 ++++++++++++++++++++++++++++-
 3 files changed, 1739 insertions(+), 7 deletions(-)
---
base-commit: 853dab01a34378871b37a5e6a800e97a997fe16c
change-id: 20231201-x1e80100-dts-missing-nodes-a09f1ed99999

Best regards,
-- 
Abel Vesa <abel.vesa@linaro.org>

[PATCH v4 01/11] arm64: dts: qcom: x1e80100: Add IPCC node

[Abel Vesa]

From: Sibi Sankar <quic_sibis@quicinc.com>

Add the IPCC node, used to send and receive IPC signals with
remoteprocs.

Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 arch/arm64/boot/dts/qcom/x1e80100.dtsi | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
index 6f75fc342ceb..954f2bd9b1de 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
@@ -691,6 +691,17 @@ gcc: clock-controller@100000 {
 			#power-domain-cells = <1>;
 		};
 
+		ipcc: mailbox@408000 {
+			compatible = "qcom,x1e80100-ipcc", "qcom,ipcc";
+			reg = <0 0x00408000 0 0x1000>;
+
+			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+
+			#mbox-cells = <2>;
+		};
+
 		gpi_dma2: dma-controller@800000 {
 			compatible = "qcom,x1e80100-gpi-dma", "qcom,sm6350-gpi-dma";
 			reg = <0 0x00800000 0 0x60000>;

-- 
2.34.1

[PATCH v4 02/11] arm64: dts: qcom: x1e80100: Add SMP2P nodes

[Abel Vesa]

From: Sibi Sankar <quic_sibis@quicinc.com>

SMP2P is used for interrupting and being interrupted about remoteproc
state changes related to the audio, compute and sensor subsystems.

Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 arch/arm64/boot/dts/qcom/x1e80100.dtsi | 53 ++++++++++++++++++++++++++++++++++
 1 file changed, 53 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
index 954f2bd9b1de..1210351b6538 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
@@ -9,6 +9,7 @@
 #include <dt-bindings/interconnect/qcom,icc.h>
 #include <dt-bindings/interconnect/qcom,x1e80100-rpmh.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/mailbox/qcom-ipcc.h>
 #include <dt-bindings/power/qcom,rpmhpd.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
@@ -662,6 +663,58 @@ smem_mem: smem@ffe00000 {
 		};
 	};
 
+	smp2p-adsp {
+		compatible = "qcom,smp2p";
+
+		interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
+					     IPCC_MPROC_SIGNAL_SMP2P
+					     IRQ_TYPE_EDGE_RISING>;
+
+		mboxes = <&ipcc IPCC_CLIENT_LPASS
+				IPCC_MPROC_SIGNAL_SMP2P>;
+
+		qcom,smem = <443>, <429>;
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <2>;
+
+		smp2p_adsp_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		smp2p_adsp_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smp2p-cdsp {
+		compatible = "qcom,smp2p";
+
+		interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
+					     IPCC_MPROC_SIGNAL_SMP2P
+					     IRQ_TYPE_EDGE_RISING>;
+
+		mboxes = <&ipcc IPCC_CLIENT_CDSP
+				IPCC_MPROC_SIGNAL_SMP2P>;
+
+		qcom,smem = <94>, <432>;
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <5>;
+
+		smp2p_cdsp_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		smp2p_cdsp_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
 	soc: soc@0 {
 		compatible = "simple-bus";
 

-- 
2.34.1

[PATCH v4 03/11] arm64: dts: qcom: x1e80100: Add QMP AOSS node

[Abel Vesa]

From: Sibi Sankar <quic_sibis@quicinc.com>

Add a node for the QMP AOSS.

Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 arch/arm64/boot/dts/qcom/x1e80100.dtsi | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
index 1210351b6538..3790d99eb298 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
@@ -2663,6 +2663,18 @@ pdc: interrupt-controller@b220000 {
 			interrupt-controller;
 		};
 
+		aoss_qmp: power-management@c300000 {
+			compatible = "qcom,x1e80100-aoss-qmp", "qcom,aoss-qmp";
+			reg = <0 0x0c300000 0 0x400>;
+			interrupt-parent = <&ipcc>;
+			interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP
+						     IRQ_TYPE_EDGE_RISING>;
+			mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+			#clock-cells = <0>;
+		};
+
+
 		tlmm: pinctrl@f100000 {
 			compatible = "qcom,x1e80100-tlmm";
 			reg = <0 0x0f100000 0 0xf00000>;

-- 
2.34.1

[PATCH v4 04/11] arm64: dts: qcom: x1e80100: Add ADSP/CDSP remoteproc nodes

[Abel Vesa]

From: Sibi Sankar <quic_sibis@quicinc.com>

Add ADSP and CDSP remoteproc nodes on X1E80100 platforms.

Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 arch/arm64/boot/dts/qcom/x1e80100.dtsi | 98 ++++++++++++++++++++++++++++++++++
 1 file changed, 98 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
index 3790d99eb298..be69e71b7f53 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
@@ -3590,6 +3590,104 @@ system-cache-controller@25000000 {
 				    "llcc_broadcast_base";
 			interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
 		};
+
+		remoteproc_adsp: remoteproc@30000000 {
+			compatible = "qcom,x1e80100-adsp-pas";
+			reg = <0 0x30000000 0 0x100>;
+
+			interrupts-extended = <&pdc 6 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog",
+					  "fatal",
+					  "ready",
+					  "handover",
+					  "stop-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			power-domains = <&rpmhpd RPMHPD_LCX>,
+					<&rpmhpd RPMHPD_LMX>;
+			power-domain-names = "lcx",
+					     "lmx";
+
+			interconnects = <&lpass_lpicx_noc MASTER_LPASS_PROC QCOM_ICC_TAG_ALWAYS
+					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+
+			memory-region = <&adspslpi_mem>,
+					<&q6_adsp_dtb_mem>;
+
+			qcom,qmp = <&aoss_qmp>;
+
+			qcom,smem-states = <&smp2p_adsp_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
+							     IPCC_MPROC_SIGNAL_GLINK_QMP
+							     IRQ_TYPE_EDGE_RISING>;
+				mboxes = <&ipcc IPCC_CLIENT_LPASS
+						IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+				label = "lpass";
+				qcom,remote-pid = <2>;
+			};
+		};
+
+		remoteproc_cdsp: remoteproc@32300000 {
+			compatible = "qcom,x1e80100-cdsp-pas";
+			reg = <0 0x32300000 0 0x1400000>;
+
+			interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_cdsp_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_cdsp_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_cdsp_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_cdsp_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog",
+					  "fatal",
+					  "ready",
+					  "handover",
+					  "stop-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			power-domains = <&rpmhpd RPMHPD_CX>,
+					<&rpmhpd RPMHPD_MXC>,
+					<&rpmhpd RPMHPD_NSP>;
+			power-domain-names = "cx",
+					     "mxc",
+					     "nsp";
+
+			interconnects = <&nsp_noc MASTER_CDSP_PROC QCOM_ICC_TAG_ALWAYS
+					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+
+			memory-region = <&cdsp_mem>,
+					<&q6_cdsp_dtb_mem>;
+
+			qcom,qmp = <&aoss_qmp>;
+
+			qcom,smem-states = <&smp2p_cdsp_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
+							     IPCC_MPROC_SIGNAL_GLINK_QMP
+							     IRQ_TYPE_EDGE_RISING>;
+				mboxes = <&ipcc IPCC_CLIENT_CDSP
+						IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+				label = "cdsp";
+				qcom,remote-pid = <5>;
+			};
+		};
 	};
 
 	timer {

-- 
2.34.1

[PATCH v4 05/11] arm64: dts: qcom: x1e80100: Add TCSR node

[Abel Vesa]

Add the TCSR clock controller and halt register space node.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 arch/arm64/boot/dts/qcom/x1e80100.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
index be69e71b7f53..2b6c55a486b2 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
@@ -2606,6 +2606,14 @@ tcsr_mutex: hwlock@1f40000 {
 			#hwlock-cells = <1>;
 		};
 
+		tcsr: clock-controller@1fc0000 {
+			compatible = "qcom,x1e80100-tcsr", "syscon";
+			reg = <0 0x01fc0000 0 0x30000>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
 		gem_noc: interconnect@26400000 {
 			compatible = "qcom,x1e80100-gem-noc";
 			reg = <0 0x26400000 0 0x311200>;

-- 
2.34.1

[PATCH v4 06/11] arm64: dts: qcom: x1e80100: Add USB nodes

[Abel Vesa]

Add nodes for all USB controllers and their PHYs for X1E80100 platform.

Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 arch/arm64/boot/dts/qcom/x1e80100.dtsi | 435 ++++++++++++++++++++++++++++++++-
 1 file changed, 432 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
index 2b6c55a486b2..593ead89706c 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
@@ -5,11 +5,13 @@
 
 #include <dt-bindings/clock/qcom,rpmh.h>
 #include <dt-bindings/clock/qcom,x1e80100-gcc.h>
+#include <dt-bindings/clock/qcom,x1e80100-tcsr.h>
 #include <dt-bindings/dma/qcom-gpi.h>
 #include <dt-bindings/interconnect/qcom,icc.h>
 #include <dt-bindings/interconnect/qcom,x1e80100-rpmh.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/mailbox/qcom-ipcc.h>
+#include <dt-bindings/phy/phy-qcom-qmp.h>
 #include <dt-bindings/power/qcom,rpmhpd.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
@@ -734,9 +736,9 @@ gcc: clock-controller@100000 {
 				 <0>,
 				 <0>,
 				 <0>,
-				 <0>,
-				 <0>,
-				 <0>;
+				 <&usb_1_ss0_qmpphy QMP_USB43DP_USB3_PIPE_CLK>,
+				 <&usb_1_ss1_qmpphy QMP_USB43DP_USB3_PIPE_CLK>,
+				 <&usb_1_ss2_qmpphy QMP_USB43DP_USB3_PIPE_CLK>;
 
 			power-domains = <&rpmhpd RPMHPD_CX>;
 			#clock-cells = <1>;
@@ -2492,6 +2494,126 @@ &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>,
 			};
 		};
 
+		usb_1_ss0_hsphy: phy@fd3000 {
+			compatible = "qcom,x1e80100-snps-eusb2-phy",
+				     "qcom,sm8550-snps-eusb2-phy";
+			reg = <0 0x00fd3000 0 0x154>;
+			#phy-cells = <0>;
+
+			clocks = <&tcsr TCSR_USB2_1_CLKREF_EN>;
+			clock-names = "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+
+			status = "disabled";
+		};
+
+		usb_1_ss0_qmpphy: phy@fd5000 {
+			compatible = "qcom,x1e80100-qmp-usb3-dp-phy";
+			reg = <0 0x00fd5000 0 0x4000>;
+
+			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
+				 <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+			clock-names = "aux",
+				      "ref",
+				      "com_aux",
+				      "usb3_pipe";
+
+			power-domains = <&gcc GCC_USB_0_PHY_GDSC>;
+
+			resets = <&gcc GCC_USB3_PHY_PRIM_BCR>,
+				 <&gcc GCC_USB4_0_DP0_PHY_PRIM_BCR>;
+			reset-names = "phy",
+				      "common";
+
+			#clock-cells = <1>;
+			#phy-cells = <1>;
+
+			status = "disabled";
+		};
+
+		usb_1_ss1_hsphy: phy@fd9000 {
+			compatible = "qcom,x1e80100-snps-eusb2-phy",
+				     "qcom,sm8550-snps-eusb2-phy";
+			reg = <0 0x00fd9000 0 0x154>;
+			#phy-cells = <0>;
+
+			clocks = <&tcsr TCSR_USB2_1_CLKREF_EN>;
+			clock-names = "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_SEC_BCR>;
+
+			status = "disabled";
+		};
+
+		usb_1_ss1_qmpphy: phy@fda000 {
+			compatible = "qcom,x1e80100-qmp-usb3-dp-phy";
+			reg = <0 0x00fda000 0 0x4000>;
+
+			clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>,
+				 <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
+			clock-names = "aux",
+				      "ref",
+				      "com_aux",
+				      "usb3_pipe";
+
+			power-domains = <&gcc GCC_USB_1_PHY_GDSC>;
+
+			resets = <&gcc GCC_USB3_PHY_SEC_BCR>,
+				 <&gcc GCC_USB4_1_DP0_PHY_SEC_BCR>;
+			reset-names = "phy",
+				      "common";
+
+			#clock-cells = <1>;
+			#phy-cells = <1>;
+
+			status = "disabled";
+		};
+
+		usb_1_ss2_hsphy: phy@fde000 {
+			compatible = "qcom,x1e80100-snps-eusb2-phy",
+				     "qcom,sm8550-snps-eusb2-phy";
+			reg = <0 0x00fde000 0 0x154>;
+			#phy-cells = <0>;
+
+			clocks = <&tcsr TCSR_USB2_1_CLKREF_EN>;
+			clock-names = "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_TERT_BCR>;
+
+			status = "disabled";
+		};
+
+		usb_1_ss2_qmpphy: phy@fdf000 {
+			compatible = "qcom,x1e80100-qmp-usb3-dp-phy";
+			reg = <0 0x00fdf000 0 0x4000>;
+
+			clocks = <&gcc GCC_USB3_TERT_PHY_AUX_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_USB3_TERT_PHY_COM_AUX_CLK>,
+				 <&gcc GCC_USB3_TERT_PHY_PIPE_CLK>;
+			clock-names = "aux",
+				      "ref",
+				      "com_aux",
+				      "usb3_pipe";
+
+			power-domains = <&gcc GCC_USB_2_PHY_GDSC>;
+
+			resets = <&gcc GCC_USB3_PHY_TERT_BCR>,
+				 <&gcc GCC_USB4_2_DP0_PHY_TERT_BCR>;
+			reset-names = "phy",
+				      "common";
+
+			#clock-cells = <1>;
+			#phy-cells = <1>;
+
+			status = "disabled";
+		};
+
 		cnoc_main: interconnect@1500000 {
 			compatible = "qcom,x1e80100-cnoc-main";
 			reg = <0 0x1500000 0 0x14400>;
@@ -2659,6 +2781,313 @@ lpass_lpicx_noc: interconnect@7430000 {
 			#interconnect-cells = <2>;
 		};
 
+		usb_2_hsphy: phy@88e0000 {
+			compatible = "qcom,x1e80100-snps-eusb2-phy",
+				     "qcom,sm8550-snps-eusb2-phy";
+			reg = <0 0x088e0000 0 0x154>;
+			#phy-cells = <0>;
+
+			clocks = <&tcsr TCSR_USB2_1_CLKREF_EN>;
+			clock-names = "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_USB20_HS_BCR>;
+
+			status = "disabled";
+		};
+
+		usb_1_ss2: usb@a0f8800 {
+			compatible = "qcom,x1e80100-dwc3", "qcom,dwc3";
+			reg = <0 0x0a0f8800 0 0x400>;
+
+			clocks = <&gcc GCC_CFG_NOC_USB3_TERT_AXI_CLK>,
+				 <&gcc GCC_USB30_TERT_MASTER_CLK>,
+				 <&gcc GCC_AGGRE_USB3_TERT_AXI_CLK>,
+				 <&gcc GCC_USB30_TERT_SLEEP_CLK>,
+				 <&gcc GCC_USB30_TERT_MOCK_UTMI_CLK>,
+				 <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_USB_NORTH_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_USB_SOUTH_AXI_CLK>,
+				 <&gcc GCC_SYS_NOC_USB_AXI_CLK>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi",
+				      "noc_aggr",
+				      "noc_aggr_north",
+				      "noc_aggr_south",
+				      "noc_sys";
+
+			assigned-clocks = <&gcc GCC_USB30_TERT_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_TERT_MASTER_CLK>;
+			assigned-clock-rates = <19200000>,
+					       <200000000>;
+
+			interrupts-extended = <&intc GIC_SPI 370 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 57 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 58 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 10 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "pwr_event",
+					  "dm_hs_phy_irq",
+					  "dp_hs_phy_irq",
+					  "ss_phy_irq";
+
+			power-domains = <&gcc GCC_USB30_TERT_GDSC>;
+			required-opps = <&rpmhpd_opp_nom>;
+
+			resets = <&gcc GCC_USB30_TERT_BCR>;
+
+			interconnects = <&usb_south_anoc MASTER_USB3_2 QCOM_ICC_TAG_ALWAYS
+					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
+					<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+					 &config_noc SLAVE_USB3_2 QCOM_ICC_TAG_ALWAYS>;
+			interconnect-names = "usb-ddr",
+					     "apps-usb";
+
+			wakeup-source;
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			status = "disabled";
+
+			usb_1_ss2_dwc3: usb@a000000 {
+				compatible = "snps,dwc3";
+				reg = <0 0x0a000000 0 0xcd00>;
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x14a0 0x0>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				snps,usb3_lpm_capable;
+				phys = <&usb_1_ss2_hsphy>,
+				       <&usb_1_ss2_qmpphy QMP_USB43DP_USB3_PHY>;
+				phy-names = "usb2-phy",
+				            "usb3-phy";
+
+				port {
+					usb_1_ss2_role_switch: endpoint {
+					};
+				};
+			};
+		};
+
+		usb_2: usb@a2f8800 {
+			compatible = "qcom,x1e80100-dwc3", "qcom,dwc3";
+			reg = <0 0x0a2f8800 0 0x400>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&gcc GCC_CFG_NOC_USB2_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB20_MASTER_CLK>,
+				 <&gcc GCC_AGGRE_USB2_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB20_SLEEP_CLK>,
+				 <&gcc GCC_USB20_MOCK_UTMI_CLK>,
+				 <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_USB_NORTH_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_USB_SOUTH_AXI_CLK>,
+				 <&gcc GCC_SYS_NOC_USB_AXI_CLK>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi",
+				      "noc_aggr",
+				      "noc_aggr_north",
+				      "noc_aggr_south",
+				      "noc_sys";
+
+			assigned-clocks = <&gcc GCC_USB20_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB20_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <200000000>;
+
+			interrupts-extended = <&intc GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 50 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 49 IRQ_TYPE_EDGE_BOTH>;
+			interrupt-names = "pwr_event",
+					  "dp_hs_phy_irq",
+					  "dm_hs_phy_irq";
+
+			power-domains = <&gcc GCC_USB20_PRIM_GDSC>;
+			required-opps = <&rpmhpd_opp_nom>;
+
+			resets = <&gcc GCC_USB20_PRIM_BCR>;
+
+			interconnects = <&usb_north_anoc MASTER_USB2 QCOM_ICC_TAG_ALWAYS
+					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
+					<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+					 &config_noc SLAVE_USB2 QCOM_ICC_TAG_ALWAYS>;
+			interconnect-names = "usb-ddr",
+					     "apps-usb";
+
+			wakeup-source;
+
+			status = "disabled";
+
+			usb_2_dwc3: usb@a200000 {
+				compatible = "snps,dwc3";
+				reg = <0 0x0a200000 0 0xcd00>;
+				interrupts = <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x14e0 0x0>;
+				phys = <&usb_2_hsphy>;
+				phy-names = "usb2-phy";
+				maximum-speed = "high-speed";
+
+				port {
+					usb_2_role_switch: endpoint {
+					};
+				};
+			};
+		};
+
+		usb_1_ss0: usb@a6f8800 {
+			compatible = "qcom,x1e80100-dwc3", "qcom,dwc3";
+			reg = <0 0x0a6f8800 0 0x400>;
+
+			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
+				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+				 <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>,
+				 <&gcc GCC_CFG_NOC_USB_ANOC_NORTH_AHB_CLK>,
+				 <&gcc GCC_CFG_NOC_USB_ANOC_SOUTH_AHB_CLK>,
+				 <&gcc GCC_SYS_NOC_USB_AXI_CLK>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi",
+				      "noc_aggr",
+				      "noc_aggr_north",
+				      "noc_aggr_south",
+				      "noc_sys";
+
+			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
+			assigned-clock-rates = <19200000>,
+					       <200000000>;
+
+			interrupts-extended = <&intc GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 15 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 61 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 17 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "pwr_event",
+					  "dm_hs_phy_irq",
+					  "dp_hs_phy_irq",
+					  "ss_phy_irq";
+
+			power-domains = <&gcc GCC_USB30_PRIM_GDSC>;
+			required-opps = <&rpmhpd_opp_nom>;
+
+			resets = <&gcc GCC_USB30_PRIM_BCR>;
+
+			wakeup-source;
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			status = "disabled";
+
+			usb_1_ss0_dwc3: usb@a600000 {
+				compatible = "snps,dwc3";
+				reg = <0 0x0a600000 0 0xcd00>;
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x1420 0x0>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				snps,usb3_lpm_capable;
+				phys = <&usb_1_ss0_hsphy>,
+				       <&usb_1_ss0_qmpphy QMP_USB43DP_USB3_PHY>;
+				phy-names = "usb2-phy",
+					    "usb3-phy";
+
+				port {
+					usb_1_ss0_role_switch: endpoint {
+					};
+				};
+			};
+		};
+
+		usb_1_ss1: usb@a8f8800 {
+			compatible = "qcom,x1e80100-dwc3", "qcom,dwc3";
+			reg = <0 0x0a8f8800 0 0x400>;
+
+			clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
+				 <&gcc GCC_USB30_SEC_MASTER_CLK>,
+				 <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>,
+				 <&gcc GCC_USB30_SEC_SLEEP_CLK>,
+				 <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
+				 <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_USB_NORTH_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_USB_SOUTH_AXI_CLK>,
+				 <&gcc GCC_SYS_NOC_USB_AXI_CLK>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi",
+				      "noc_aggr",
+				      "noc_aggr_north",
+				      "noc_aggr_south",
+				      "noc_sys";
+
+			assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_SEC_MASTER_CLK>;
+			assigned-clock-rates = <19200000>,
+					       <200000000>;
+
+			interrupts-extended = <&intc GIC_SPI 372 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 11 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 60 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 47 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "pwr_event",
+					  "dm_hs_phy_irq",
+					  "dp_hs_phy_irq",
+					  "ss_phy_irq";
+
+			power-domains = <&gcc GCC_USB30_SEC_GDSC>;
+			required-opps = <&rpmhpd_opp_nom>;
+
+			resets = <&gcc GCC_USB30_SEC_BCR>;
+
+			interconnects = <&usb_south_anoc MASTER_USB3_1 QCOM_ICC_TAG_ALWAYS
+					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
+					<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+					 &config_noc SLAVE_USB3_1 QCOM_ICC_TAG_ALWAYS>;
+			interconnect-names = "usb-ddr",
+					     "apps-usb";
+
+			wakeup-source;
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			status = "disabled";
+
+			usb_1_ss1_dwc3: usb@a800000 {
+				compatible = "snps,dwc3";
+				reg = <0 0x0a800000 0 0xcd00>;
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x1460 0x0>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				snps,usb3_lpm_capable;
+				phys = <&usb_1_ss1_hsphy>,
+				       <&usb_1_ss1_qmpphy QMP_USB43DP_USB3_PHY>;
+				phy-names = "usb2-phy",
+					    "usb3-phy";
+
+				port {
+					usb_1_ss1_role_switch: endpoint {
+					};
+				};
+			};
+		};
+
 		pdc: interrupt-controller@b220000 {
 			compatible = "qcom,x1e80100-pdc", "qcom,pdc";
 			reg = <0 0x0b220000 0 0x30000>, <0 0x174000f0 0 0x64>;

-- 
2.34.1

[PATCH v4 07/11] arm64: dts: qcom: x1e80100: Add PCIe nodes

[Abel Vesa]

Add nodes for PCIe 4 and 6 controllers and their PHYs for X1E80100 platform.

Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 arch/arm64/boot/dts/qcom/x1e80100.dtsi | 214 ++++++++++++++++++++++++++++++++-
 1 file changed, 212 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
index 593ead89706c..e8d2ea2b26ed 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
@@ -732,9 +732,9 @@ gcc: clock-controller@100000 {
 			clocks = <&bi_tcxo_div2>,
 				 <&sleep_clk>,
 				 <0>,
+				 <&pcie4_phy>,
 				 <0>,
-				 <0>,
-				 <0>,
+				 <&pcie6a_phy>,
 				 <0>,
 				 <&usb_1_ss0_qmpphy QMP_USB43DP_USB3_PIPE_CLK>,
 				 <&usb_1_ss1_qmpphy QMP_USB43DP_USB3_PIPE_CLK>,
@@ -2722,6 +2722,216 @@ mmss_noc: interconnect@1780000 {
 			#interconnect-cells = <2>;
 		};
 
+		pcie6a: pci@1bf8000 {
+			device_type = "pci";
+			compatible = "qcom,pcie-x1e80100";
+			reg = <0 0x01bf8000 0 0x3000>,
+			      <0 0x70000000 0 0xf1d>,
+			      <0 0x70000f20 0 0xa8>,
+			      <0 0x70001000 0 0x1000>,
+			      <0 0x70100000 0 0x100000>;
+			reg-names = "parf",
+				    "dbi",
+				    "elbi",
+				    "atu",
+				    "config";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges = <0x01000000 0 0x00000000 0 0x70200000 0 0x100000>,
+				 <0x02000000 0 0x70300000 0 0x70300000 0 0x3d00000>;
+			bus-range = <0 0xff>;
+
+			dma-coherent;
+
+			linux,pci-domain = <7>;
+			num-lanes = <2>;
+
+			interrupts = <GIC_SPI 773 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 0 843 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 2 &intc 0 0 0 844 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 3 &intc 0 0 0 845 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 4 &intc 0 0 0 772 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_PCIE_6A_AUX_CLK>,
+				 <&gcc GCC_PCIE_6A_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_6A_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_6A_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_6A_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_CNOC_PCIE_SOUTH_SF_AXI_CLK>;
+			clock-names = "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "noc_aggr_south_sf";
+
+			assigned-clocks = <&gcc GCC_PCIE_6A_AUX_CLK>;
+			assigned-clock-rates = <19200000>;
+
+			interconnects = <&pcie_south_anoc MASTER_PCIE_6A QCOM_ICC_TAG_ALWAYS
+					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
+					<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+					 &cnoc_main SLAVE_PCIE_6A QCOM_ICC_TAG_ALWAYS>;
+			interconnect-names = "pcie-mem",
+					     "cpu-pcie";
+
+			resets = <&gcc GCC_PCIE_6A_BCR>,
+				<&gcc GCC_PCIE_6A_LINK_DOWN_BCR>;
+			reset-names = "pci",
+				      "link_down";
+
+			power-domains = <&gcc GCC_PCIE_6A_GDSC>;
+
+			phys = <&pcie6a_phy>;
+			phy-names = "pciephy";
+
+			status = "disabled";
+		};
+
+		pcie6a_phy: phy@1bfc000 {
+			compatible = "qcom,x1e80100-qmp-gen4x2-pcie-phy";
+			reg = <0 0x01bfc000 0 0x2000>;
+
+			clocks = <&gcc GCC_PCIE_6A_PHY_AUX_CLK>,
+				 <&gcc GCC_PCIE_6A_CFG_AHB_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_PCIE_6A_PHY_RCHNG_CLK>,
+				 <&gcc GCC_PCIE_6A_PIPE_CLK>;
+			clock-names = "aux",
+				      "cfg_ahb",
+				      "ref",
+				      "rchng",
+				      "pipe";
+
+			resets = <&gcc GCC_PCIE_6A_PHY_BCR>,
+				 <&gcc GCC_PCIE_6A_NOCSR_COM_PHY_BCR>;
+			reset-names = "phy",
+				      "phy_nocsr";
+
+			assigned-clocks = <&gcc GCC_PCIE_6A_PHY_RCHNG_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			power-domains = <&gcc GCC_PCIE_6_PHY_GDSC>;
+
+			#clock-cells = <0>;
+			clock-output-names = "pcie6a_pipe_clk";
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		pcie4: pci@1c08000 {
+			device_type = "pci";
+			compatible = "qcom,pcie-x1e80100";
+			reg = <0 0x01c08000 0 0x3000>,
+			      <0 0x7c000000 0 0xf1d>,
+			      <0 0x7c000f40 0 0xa8>,
+			      <0 0x7c001000 0 0x1000>,
+			      <0 0x7c100000 0 0x100000>,
+			      <0 0x01c0b000 0 0x1000>;
+			reg-names = "parf",
+			            "dbi",
+				    "elbi",
+				    "atu",
+				    "config",
+				    "mhi";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges = <0x01000000 0 0x00000000 0 0x7c200000 0 0x100000>,
+				 <0x02000000 0 0x7c300000 0 0x7c300000 0 0x3d00000>;
+			bus-range = <0x00 0xff>;
+
+			dma-coherent;
+
+			linux,pci-domain = <5>;
+			num-lanes = <2>;
+
+			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi0",
+					  "msi1",
+					  "msi2",
+					  "msi3";
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 0 149 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 2 &intc 0 0 0 150 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 3 &intc 0 0 0 151 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 4 &intc 0 0 0 152 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_PCIE_4_AUX_CLK>,
+				 <&gcc GCC_PCIE_4_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_4_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_4_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_4_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_CNOC_PCIE_NORTH_SF_AXI_CLK>;
+			clock-names = "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "noc_aggr_south_sf";
+
+			assigned-clocks = <&gcc GCC_PCIE_4_AUX_CLK>;
+			assigned-clock-rates = <19200000>;
+
+			interconnects = <&pcie_south_anoc MASTER_PCIE_4 QCOM_ICC_TAG_ALWAYS
+					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
+					<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+					 &cnoc_main SLAVE_PCIE_4 QCOM_ICC_TAG_ALWAYS>;
+			interconnect-names = "pcie-mem",
+					     "cpu-pcie";
+
+			resets = <&gcc GCC_PCIE_4_BCR>;
+			reset-names = "pci";
+
+			power-domains = <&gcc GCC_PCIE_4_GDSC>;
+
+			phys = <&pcie4_phy>;
+			phy-names = "pciephy";
+
+			status = "disabled";
+		};
+
+		pcie4_phy: phy@1c0e000 {
+			compatible = "qcom,x1e80100-qmp-gen3x2-pcie-phy";
+			reg = <0 0x01c0e000 0 0x2000>;
+
+			clocks = <&gcc GCC_PCIE_4_AUX_CLK>,
+				 <&gcc GCC_PCIE_4_CFG_AHB_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_PCIE_4_PHY_RCHNG_CLK>,
+				 <&gcc GCC_PCIE_4_PIPE_CLK>;
+			clock-names = "aux",
+				      "cfg_ahb",
+				      "ref",
+				      "rchng",
+				      "pipe";
+
+			resets = <&gcc GCC_PCIE_4_PHY_BCR>;
+			reset-names = "phy";
+
+			assigned-clocks = <&gcc GCC_PCIE_4_PHY_RCHNG_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			power-domains = <&gcc GCC_PCIE_4_PHY_GDSC>;
+
+			#clock-cells = <0>;
+			clock-output-names = "pcie4_pipe_clk";
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
 		tcsr_mutex: hwlock@1f40000 {
 			compatible = "qcom,tcsr-mutex";
 			reg = <0 0x01f40000 0 0x20000>;

-- 
2.34.1

[PATCH v4 08/11] arm64: dts: qcom: x1e80100: Add display nodes

[Abel Vesa]

Add the required nodes to support display on X1E80100.

Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 arch/arm64/boot/dts/qcom/x1e80100.dtsi | 518 +++++++++++++++++++++++++++++++++
 1 file changed, 518 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
index e8d2ea2b26ed..247ff7a9e405 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
@@ -4,6 +4,7 @@
  */
 
 #include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/clock/qcom,x1e80100-dispcc.h>
 #include <dt-bindings/clock/qcom,x1e80100-gcc.h>
 #include <dt-bindings/clock/qcom,x1e80100-tcsr.h>
 #include <dt-bindings/dma/qcom-gpi.h>
@@ -3298,6 +3299,523 @@ usb_1_ss1_role_switch: endpoint {
 			};
 		};
 
+		mdss: display-subsystem@ae00000 {
+			compatible = "qcom,x1e80100-mdss";
+			reg = <0 0x0ae00000 0 0x1000>;
+			reg-names = "mdss";
+
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+				 <&gcc GCC_DISP_AHB_CLK>,
+				 <&gcc GCC_DISP_HF_AXI_CLK>,
+				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
+
+			resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
+
+			interconnects = <&mmss_noc MASTER_MDP QCOM_ICC_TAG_ALWAYS
+					 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+					<&mc_virt MASTER_LLCC QCOM_ICC_TAG_ALWAYS
+					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+			interconnect-names = "mdp0-mem",
+					     "mdp1-mem";
+
+			power-domains = <&dispcc DISP_CC_MDSS_CORE_GDSC>;
+
+			iommus = <&apps_smmu 0x1c00 0x2>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			status = "disabled";
+
+			mdss_mdp: display-controller@ae01000 {
+				compatible = "qcom,x1e80100-dpu";
+				reg = <0 0x0ae01000 0 0x8f000>,
+				      <0 0x0aeb0000 0 0x2008>;
+				reg-names = "mdp",
+					    "vbif";
+
+				interrupts-extended = <&mdss 0>;
+
+				clocks = <&gcc GCC_DISP_AHB_CLK>,
+					 <&gcc GCC_DISP_HF_AXI_CLK>,
+					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
+					 <&dispcc DISP_CC_MDSS_MDP_CLK>,
+					 <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+				clock-names = "bus",
+					      "nrt_bus",
+					      "iface",
+					      "lut",
+					      "core",
+					      "vsync";
+
+				operating-points-v2 = <&mdp_opp_table>;
+
+				power-domains = <&rpmhpd RPMHPD_MMCX>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						mdss_intf0_out: endpoint {
+							remote-endpoint = <&mdss_dp0_in>;
+						};
+					};
+
+					port@4 {
+						reg = <4>;
+
+						mdss_intf4_out: endpoint {
+							remote-endpoint = <&mdss_dp1_in>;
+						};
+					};
+
+					port@5 {
+						reg = <5>;
+
+						mdss_intf5_out: endpoint {
+							remote-endpoint = <&mdss_dp3_in>;
+						};
+					};
+
+					port@6 {
+						reg = <6>;
+
+						mdss_intf6_out: endpoint {
+							remote-endpoint = <&mdss_dp2_in>;
+						};
+					};
+				};
+
+				mdp_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-200000000 {
+						opp-hz = /bits/ 64 <200000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-325000000 {
+						opp-hz = /bits/ 64 <325000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-375000000 {
+						opp-hz = /bits/ 64 <375000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-514000000 {
+						opp-hz = /bits/ 64 <514000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+
+					opp-575000000 {
+						opp-hz = /bits/ 64 <575000000>;
+						required-opps = <&rpmhpd_opp_nom_l1>;
+					};
+				};
+			};
+
+			mdss_dp0: displayport-controller@ae90000 {
+				compatible = "qcom,x1e80100-dp", "qcom,sm8350-dp";
+				reg = <0 0xae90000 0 0x200>,
+				      <0 0xae90200 0 0x200>,
+				      <0 0xae90400 0 0x600>,
+				      <0 0xae91000 0 0x400>,
+				      <0 0xae91400 0 0x400>;
+
+				interrupts-extended = <&mdss 12>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX0_AUX_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX0_LINK_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX0_LINK_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX0_PIXEL0_CLK>;
+				clock-names = "core_iface",
+					      "core_aux",
+					      "ctrl_link",
+					      "ctrl_link_iface",
+					      "stream_pixel";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_DPTX0_LINK_CLK_SRC>,
+						  <&dispcc DISP_CC_MDSS_DPTX0_PIXEL0_CLK_SRC>;
+				assigned-clock-parents = <&usb_1_ss0_qmpphy QMP_USB43DP_DP_LINK_CLK>,
+							 <&usb_1_ss0_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>;
+
+				operating-points-v2 = <&mdss_dp0_opp_table>;
+
+				power-domains = <&rpmhpd RPMHPD_MMCX>;
+
+				phys = <&usb_1_ss0_qmpphy QMP_USB43DP_DP_PHY>;
+				phy-names = "dp";
+
+				#sound-dai-cells = <0>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						mdss_dp0_in: endpoint {
+							remote-endpoint = <&mdss_intf0_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						mdss_dp0_out: endpoint {
+						};
+					};
+				};
+
+				mdss_dp0_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-160000000 {
+						opp-hz = /bits/ 64 <160000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-270000000 {
+						opp-hz = /bits/ 64 <270000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-540000000 {
+						opp-hz = /bits/ 64 <540000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-810000000 {
+						opp-hz = /bits/ 64 <810000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+			};
+
+			mdss_dp1: displayport-controller@ae98000 {
+				compatible = "qcom,x1e80100-dp", "qcom,sm8350-dp";
+				reg = <0 0xae98000 0 0x200>,
+				      <0 0xae98200 0 0x200>,
+				      <0 0xae98400 0 0x600>,
+				      <0 0xae99000 0 0x400>,
+				      <0 0xae99400 0 0x400>;
+
+				interrupts-extended = <&mdss 13>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX1_AUX_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX1_LINK_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX1_LINK_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX1_PIXEL0_CLK>;
+				clock-names = "core_iface",
+					      "core_aux",
+					      "ctrl_link",
+					      "ctrl_link_iface",
+					      "stream_pixel";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_DPTX1_LINK_CLK_SRC>,
+						  <&dispcc DISP_CC_MDSS_DPTX1_PIXEL0_CLK_SRC>;
+				assigned-clock-parents = <&usb_1_ss1_qmpphy QMP_USB43DP_DP_LINK_CLK>,
+							 <&usb_1_ss1_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>;
+
+				operating-points-v2 = <&mdss_dp1_opp_table>;
+
+				power-domains = <&rpmhpd RPMHPD_MMCX>;
+
+				phys = <&usb_1_ss1_qmpphy QMP_USB43DP_DP_PHY>;
+				phy-names = "dp";
+
+				#sound-dai-cells = <0>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						mdss_dp1_in: endpoint {
+							remote-endpoint = <&mdss_intf4_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						mdss_dp1_out: endpoint {
+						};
+					};
+				};
+
+				mdss_dp1_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-160000000 {
+						opp-hz = /bits/ 64 <160000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-270000000 {
+						opp-hz = /bits/ 64 <270000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-540000000 {
+						opp-hz = /bits/ 64 <540000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-810000000 {
+						opp-hz = /bits/ 64 <810000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+			};
+
+			mdss_dp2: displayport-controller@ae9a000 {
+				compatible = "qcom,x1e80100-dp", "qcom,sm8350-dp";
+				reg = <0 0xae9a000 0 0x200>,
+				      <0 0xae9a200 0 0x200>,
+				      <0 0xae9a400 0 0x600>,
+				      <0 0xae9b000 0 0x400>,
+				      <0 0xae9b400 0 0x400>;
+
+				interrupts-extended = <&mdss 14>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX2_AUX_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX2_LINK_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX2_LINK_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX2_PIXEL0_CLK>;
+				clock-names = "core_iface",
+					      "core_aux",
+					      "ctrl_link",
+					      "ctrl_link_iface",
+					      "stream_pixel";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_DPTX2_LINK_CLK_SRC>,
+						  <&dispcc DISP_CC_MDSS_DPTX2_PIXEL0_CLK_SRC>;
+				assigned-clock-parents = <&mdss_dp2_phy 0>,
+							 <&mdss_dp2_phy 1>;
+
+				operating-points-v2 = <&mdss_dp2_opp_table>;
+
+				power-domains = <&rpmhpd RPMHPD_MMCX>;
+
+				phys = <&mdss_dp2_phy>;
+				phy-names = "dp";
+
+				#sound-dai-cells = <0>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						mdss_dp2_in: endpoint {
+							remote-endpoint = <&mdss_intf6_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+					};
+				};
+
+				mdss_dp2_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-160000000 {
+						opp-hz = /bits/ 64 <160000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-270000000 {
+						opp-hz = /bits/ 64 <270000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-540000000 {
+						opp-hz = /bits/ 64 <540000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-810000000 {
+						opp-hz = /bits/ 64 <810000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+			};
+
+			mdss_dp3: displayport-controller@aea0000 {
+				compatible = "qcom,x1e80100-dp", "qcom,sm8350-dp";
+				reg = <0 0xaea0000 0 0x200>,
+				      <0 0xaea0200 0 0x200>,
+				      <0 0xaea0400 0 0x600>,
+				      <0 0xaea1000 0 0x400>,
+				      <0 0xaea1400 0 0x400>;
+
+				interrupts-extended = <&mdss 15>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX3_AUX_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX3_LINK_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX3_LINK_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX3_PIXEL0_CLK>;
+				clock-names = "core_iface",
+					      "core_aux",
+					      "ctrl_link",
+					      "ctrl_link_iface",
+					      "stream_pixel";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_DPTX3_LINK_CLK_SRC>,
+						  <&dispcc DISP_CC_MDSS_DPTX3_PIXEL0_CLK_SRC>;
+				assigned-clock-parents = <&mdss_dp3_phy 0>,
+							 <&mdss_dp3_phy 1>;
+
+				operating-points-v2 = <&mdss_dp3_opp_table>;
+
+				power-domains = <&rpmhpd RPMHPD_MMCX>;
+
+				phys = <&mdss_dp3_phy>;
+				phy-names = "dp";
+
+				#sound-dai-cells = <0>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						mdss_dp3_in: endpoint {
+							remote-endpoint = <&mdss_intf5_out>;
+
+							link-frequencies = /bits/ 64 <8100000000>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+					};
+				};
+
+				mdss_dp3_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-160000000 {
+						opp-hz = /bits/ 64 <160000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-270000000 {
+						opp-hz = /bits/ 64 <270000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-540000000 {
+						opp-hz = /bits/ 64 <540000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-810000000 {
+						opp-hz = /bits/ 64 <810000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+			};
+
+		};
+
+		mdss_dp2_phy: phy@aec2a00 {
+			compatible = "qcom,x1e80100-dp-phy";
+			reg = <0 0x0aec2a00 0 0x19c>,
+			      <0 0x0aec2200 0 0xec>,
+			      <0 0x0aec2600 0 0xec>,
+			      <0 0x0aec2000 0 0x1c8>;
+
+			clocks = <&dispcc DISP_CC_MDSS_DPTX2_AUX_CLK>,
+				 <&dispcc DISP_CC_MDSS_AHB_CLK>;
+			clock-names = "aux",
+				      "cfg_ahb";
+
+			power-domains = <&rpmhpd RPMHPD_MX>;
+
+			#clock-cells = <1>;
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		mdss_dp3_phy: phy@aec5a00 {
+			compatible = "qcom,x1e80100-dp-phy";
+			reg = <0 0x0aec5a00 0 0x19c>,
+			      <0 0x0aec5200 0 0xec>,
+			      <0 0x0aec5600 0 0xec>,
+			      <0 0x0aec5000 0 0x1c8>;
+
+			clocks = <&dispcc DISP_CC_MDSS_DPTX3_AUX_CLK>,
+				 <&dispcc DISP_CC_MDSS_AHB_CLK>;
+			clock-names = "aux",
+				      "cfg_ahb";
+
+			power-domains = <&rpmhpd RPMHPD_MX>;
+
+			#clock-cells = <1>;
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		dispcc: clock-controller@af00000 {
+			compatible = "qcom,x1e80100-dispcc";
+			reg = <0 0x0af00000 0 0x20000>;
+			clocks = <&bi_tcxo_div2>,
+				 <&bi_tcxo_ao_div2>,
+				 <&gcc GCC_DISP_AHB_CLK>,
+				 <&sleep_clk>,
+				 <0>, /* dsi0 */
+				 <0>,
+				 <0>, /* dsi1 */
+				 <0>,
+				 <&usb_1_ss0_qmpphy QMP_USB43DP_DP_LINK_CLK>, /* dp0 */
+				 <&usb_1_ss0_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>,
+				 <&usb_1_ss1_qmpphy QMP_USB43DP_DP_LINK_CLK>, /* dp1 */
+				 <&usb_1_ss1_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>,
+				 <&mdss_dp2_phy 0>, /* dp2 */
+				 <&mdss_dp2_phy 1>,
+				 <&mdss_dp3_phy 0>, /* dp3 */
+				 <&mdss_dp3_phy 1>;
+			power-domains = <&rpmhpd RPMHPD_MMCX>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+		};
+
 		pdc: interrupt-controller@b220000 {
 			compatible = "qcom,x1e80100-pdc", "qcom,pdc";
 			reg = <0 0x0b220000 0 0x30000>, <0 0x174000f0 0 0x64>;

-- 
2.34.1

[PATCH v4 09/11] arm64: dts: qcom: x1e80100-crd: Enable more support

[Abel Vesa]

Enable touchscreen, touchpad, keyboard, display, pcie and usb
support.

Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 arch/arm64/boot/dts/qcom/x1e80100-crd.dts | 222 ++++++++++++++++++++++++++++++
 1 file changed, 222 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
index 7532d8eca2de..7e7cc8e43f87 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
+++ b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
@@ -401,10 +401,145 @@ vreg_l3j_0p8: ldo3 {
 	};
 };
 
+&i2c0 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	touchpad@15 {
+		compatible = "hid-over-i2c";
+		reg = <0x15>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-0 = <&tpad_default>;
+		pinctrl-names = "default";
+
+		wakeup-source;
+	};
+
+	keyboard@3a {
+		compatible = "hid-over-i2c";
+		reg = <0x3a>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-0 = <&kybd_default>;
+		pinctrl-names = "default";
+
+		wakeup-source;
+	};
+};
+
+&i2c8 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	touchscreen@10 {
+		compatible = "hid-over-i2c";
+		reg = <0x10>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-0 = <&ts0_default>;
+		pinctrl-names = "default";
+	};
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dp3 {
+	compatible = "qcom,x1e80100-dp";
+	/delete-property/ #sound-dai-cells;
+
+	data-lanes = <0 1 2 3>;
+
+	status = "okay";
+
+	aux-bus {
+		panel {
+			compatible = "edp-panel";
+			power-supply = <&vreg_edp_3p3>;
+
+			port {
+				edp_panel_in: endpoint {
+					remote-endpoint = <&mdss_dp3_out>;
+				};
+			};
+		};
+	};
+
+	ports {
+		port@1 {
+			reg = <1>;
+			mdss_dp3_out: endpoint {
+				remote-endpoint = <&edp_panel_in>;
+			};
+		};
+	};
+};
+
+&mdss_dp3_phy {
+	vdda-phy-supply = <&vreg_l3j_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&pcie4 {
+	status = "okay";
+};
+
+&pcie4_phy {
+	vdda-phy-supply = <&vreg_l3j_0p8>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&pcie6a {
+	status = "okay";
+};
+
+&pcie6a_phy {
+	vdda-phy-supply = <&vreg_l3j_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&qupv3_0 {
+	status = "okay";
+};
+
+&qupv3_1 {
+	status = "okay";
+};
+
 &qupv3_2 {
 	status = "okay";
 };
 
+&remoteproc_adsp {
+	firmware-name = "qcom/x1e80100/adsp.mbn",
+			"qcom/x1e80100/adsp_dtb.mbn";
+
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/x1e80100/cdsp.mbn",
+			"qcom/x1e80100/cdsp_dtb.mbn";
+
+	status = "okay";
+};
+
 &tlmm {
 	gpio-reserved-ranges = <34 2>, /* Unused */
 			       <44 4>, /* SPI (TPM) */
@@ -416,9 +551,96 @@ edp_reg_en: edp-reg-en-state {
 		drive-strength = <16>;
 		bias-disable;
 	};
+
+	kybd_default: kybd-default-state {
+		pins = "gpio67";
+		function = "gpio";
+		bias-disable;
+	};
+
+	tpad_default: tpad-default-state {
+		pins = "gpio3";
+		function = "gpio";
+		bias-disable;
+	};
+
+	ts0_default: ts0-default-state {
+		int-n-pins {
+			pins = "gpio51";
+			function = "gpio";
+			bias-disable;
+		};
+
+		reset-n-pins {
+			pins = "gpio48";
+			function = "gpio";
+			output-high;
+			drive-strength = <16>;
+		};
+	};
 };
 
 &uart21 {
 	compatible = "qcom,geni-debug-uart";
 	status = "okay";
 };
+
+&usb_1_ss0_hsphy {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&usb_1_ss0_qmpphy {
+	status = "okay";
+};
+
+&usb_1_ss0 {
+	status = "okay";
+};
+
+&usb_1_ss0_dwc3 {
+	dr_mode = "host";
+	usb-role-switch;
+};
+
+&usb_1_ss1_hsphy {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&usb_1_ss1_qmpphy {
+	status = "okay";
+};
+
+&usb_1_ss1 {
+	status = "okay";
+};
+
+&usb_1_ss1_dwc3 {
+	dr_mode = "host";
+	usb-role-switch;
+};
+
+&usb_1_ss2_hsphy {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&usb_1_ss2_qmpphy {
+	status = "okay";
+};
+
+&usb_1_ss2 {
+	status = "okay";
+};
+
+&usb_1_ss2_dwc3 {
+	dr_mode = "host";
+	usb-role-switch;
+};

-- 
2.34.1

[PATCH v4 10/11] arm64: dts: qcom: x1e80100-qcp: Enable more support

[Abel Vesa]

Enable display, pcie and usb support.

Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 arch/arm64/boot/dts/qcom/x1e80100-qcp.dts | 171 ++++++++++++++++++++++++++++++
 1 file changed, 171 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts b/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
index a37ad9475c90..8dbf6d0eaac3 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
+++ b/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 
 #include "x1e80100.dtsi"
@@ -31,6 +32,23 @@ vph_pwr: vph-pwr-regulator {
 		regulator-always-on;
 		regulator-boot-on;
 	};
+
+	vreg_edp_3p3: regulator-edp-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_EDP_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&edp_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
 };
 
 &apps_rsc {
@@ -383,17 +401,170 @@ vreg_l3j_0p8: ldo3 {
 	};
 };
 
+&mdss {
+	status = "okay";
+};
+
+&mdss_dp3 {
+	compatible = "qcom,x1e80100-dp";
+	/delete-property/ #sound-dai-cells;
+
+	data-lanes = <0 1 2 3>;
+
+	status = "okay";
+
+	aux-bus {
+		panel {
+			compatible = "edp-panel";
+			power-supply = <&vreg_edp_3p3>;
+
+			port {
+				edp_panel_in: endpoint {
+					remote-endpoint = <&mdss_dp3_out>;
+				};
+			};
+		};
+	};
+
+	ports {
+		port@1 {
+			reg = <1>;
+			mdss_dp3_out: endpoint {
+				remote-endpoint = <&edp_panel_in>;
+			};
+		};
+	};
+};
+
+&mdss_dp3_phy {
+	vdda-phy-supply = <&vreg_l3j_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&pcie4 {
+	status = "okay";
+};
+
+&pcie4_phy {
+	vdda-phy-supply = <&vreg_l3j_0p8>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&pcie6a {
+	status = "okay";
+};
+
+&pcie6a_phy {
+	vdda-phy-supply = <&vreg_l3j_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&qupv3_0 {
+	status = "okay";
+};
+
+&qupv3_1 {
+	status = "okay";
+};
+
 &qupv3_2 {
 	status = "okay";
 };
 
+&remoteproc_adsp {
+	firmware-name = "qcom/x1e80100/adsp.mbn",
+			"qcom/x1e80100/adsp_dtb.mbn";
+
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/x1e80100/cdsp.mbn",
+			"qcom/x1e80100/cdsp_dtb.mbn";
+
+	status = "okay";
+};
+
 &tlmm {
 	gpio-reserved-ranges = <33 3>, /* Unused */
 			       <44 4>, /* SPI (TPM) */
 			       <238 1>; /* UFS Reset */
+
+	edp_reg_en: edp-reg-en-state {
+		pins = "gpio70";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
 };
 
 &uart21 {
 	compatible = "qcom,geni-debug-uart";
 	status = "okay";
 };
+
+&usb_1_ss0_hsphy {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&usb_1_ss0_qmpphy {
+	status = "okay";
+};
+
+&usb_1_ss0 {
+	status = "okay";
+};
+
+&usb_1_ss0_dwc3 {
+	dr_mode = "host";
+	usb-role-switch;
+};
+
+&usb_1_ss1_hsphy {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&usb_1_ss1_qmpphy {
+	status = "okay";
+};
+
+&usb_1_ss1 {
+	status = "okay";
+};
+
+&usb_1_ss1_dwc3 {
+	dr_mode = "host";
+	usb-role-switch;
+};
+
+&usb_1_ss2_hsphy {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&usb_1_ss2_qmpphy {
+	status = "okay";
+};
+
+&usb_1_ss2 {
+	status = "okay";
+};
+
+&usb_1_ss2_dwc3 {
+	dr_mode = "host";
+	usb-role-switch;
+};

-- 
2.34.1

[PATCH v4 11/11] arm64: dts: qcom: x1e80100-qcp: Fix supplies for LDOs 3E and 2J

[Abel Vesa]

The LDOs 3E and 2J are actually supplied by SMPS 5J. Fix accordingly.

Fixes: af16b00578a7 ("arm64: dts: qcom: Add base X1E80100 dtsi and the QCP dts")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 arch/arm64/boot/dts/qcom/x1e80100-qcp.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts b/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
index 8dbf6d0eaac3..e76d29053d79 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
+++ b/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
@@ -261,7 +261,7 @@ regulators-3 {
 		qcom,pmic-id = "e";
 
 		vdd-l2-supply = <&vreg_s1f_0p7>;
-		vdd-l3-supply = <&vph_pwr>;
+		vdd-l3-supply = <&vreg_s5j_1p2>;
 
 		vreg_l2e_0p8: ldo2 {
 			regulator-name = "vreg_l2e_0p8";
@@ -367,7 +367,7 @@ regulators-7 {
 		qcom,pmic-id = "j";
 
 		vdd-l1-supply = <&vreg_s1f_0p7>;
-		vdd-l2-supply = <&vph_pwr>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
 		vdd-l3-supply = <&vreg_s1f_0p7>;
 		vdd-s5-supply = <&vph_pwr>;
 

-- 
2.34.1

Re: [PATCH v4 01/11] arm64: dts: qcom: x1e80100: Add IPCC node

[Konrad Dybcio]

On 1/23/24 12:01, Abel Vesa wrote:
> From: Sibi Sankar <quic_sibis@quicinc.com>
> 
> Add the IPCC node, used to send and receive IPC signals with
> remoteprocs.
> 
> Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad

Re: [PATCH v4 03/11] arm64: dts: qcom: x1e80100: Add QMP AOSS node

[Konrad Dybcio]

On 1/23/24 12:01, Abel Vesa wrote:
> From: Sibi Sankar <quic_sibis@quicinc.com>
> 
> Add a node for the QMP AOSS.
> 
> Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad

Re: [PATCH v4 05/11] arm64: dts: qcom: x1e80100: Add TCSR node

[Konrad Dybcio]

On 1/23/24 12:01, Abel Vesa wrote:
> Add the TCSR clock controller and halt register space node.
> 
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---

The former - yes, the latter - ?

Konrad
>   arch/arm64/boot/dts/qcom/x1e80100.dtsi | 8 ++++++++
>   1 file changed, 8 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> index be69e71b7f53..2b6c55a486b2 100644
> --- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> +++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> @@ -2606,6 +2606,14 @@ tcsr_mutex: hwlock@1f40000 {
>   			#hwlock-cells = <1>;
>   		};
>   
> +		tcsr: clock-controller@1fc0000 {
> +			compatible = "qcom,x1e80100-tcsr", "syscon";
> +			reg = <0 0x01fc0000 0 0x30000>;
> +			clocks = <&rpmhcc RPMH_CXO_CLK>;
> +			#clock-cells = <1>;
> +			#reset-cells = <1>;
> +		};
> +
>   		gem_noc: interconnect@26400000 {
>   			compatible = "qcom,x1e80100-gem-noc";
>   			reg = <0 0x26400000 0 0x311200>;
> 

Re: [PATCH v4 06/11] arm64: dts: qcom: x1e80100: Add USB nodes

[Konrad Dybcio]

On 1/23/24 12:01, Abel Vesa wrote:
> Add nodes for all USB controllers and their PHYs for X1E80100 platform.
> 
> Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
> Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
> Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
> Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>   arch/arm64/boot/dts/qcom/x1e80100.dtsi | 435 ++++++++++++++++++++++++++++++++-
>   1 file changed, 432 insertions(+), 3 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> index 2b6c55a486b2..593ead89706c 100644
> --- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> +++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> @@ -5,11 +5,13 @@
>   
>   #include <dt-bindings/clock/qcom,rpmh.h>
>   #include <dt-bindings/clock/qcom,x1e80100-gcc.h>
> +#include <dt-bindings/clock/qcom,x1e80100-tcsr.h>
>   #include <dt-bindings/dma/qcom-gpi.h>
>   #include <dt-bindings/interconnect/qcom,icc.h>
>   #include <dt-bindings/interconnect/qcom,x1e80100-rpmh.h>
>   #include <dt-bindings/interrupt-controller/arm-gic.h>
>   #include <dt-bindings/mailbox/qcom-ipcc.h>
> +#include <dt-bindings/phy/phy-qcom-qmp.h>
>   #include <dt-bindings/power/qcom,rpmhpd.h>
>   #include <dt-bindings/power/qcom-rpmpd.h>
>   #include <dt-bindings/soc/qcom,rpmh-rsc.h>
> @@ -734,9 +736,9 @@ gcc: clock-controller@100000 {
>   				 <0>,
>   				 <0>,
>   				 <0>,
> -				 <0>,
> -				 <0>,
> -				 <0>;
> +				 <&usb_1_ss0_qmpphy QMP_USB43DP_USB3_PIPE_CLK>,
> +				 <&usb_1_ss1_qmpphy QMP_USB43DP_USB3_PIPE_CLK>,
> +				 <&usb_1_ss2_qmpphy QMP_USB43DP_USB3_PIPE_CLK>;
>   
>   			power-domains = <&rpmhpd RPMHPD_CX>;
>   			#clock-cells = <1>;
> @@ -2492,6 +2494,126 @@ &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>,
>   			};
>   		};
>   
> +		usb_1_ss0_hsphy: phy@fd3000 {
> +			compatible = "qcom,x1e80100-snps-eusb2-phy",
> +				     "qcom,sm8550-snps-eusb2-phy";
> +			reg = <0 0x00fd3000 0 0x154>;
> +			#phy-cells = <0>;
> +
> +			clocks = <&tcsr TCSR_USB2_1_CLKREF_EN>;
> +			clock-names = "ref";

You use this exact same clock for all HS PHYs. Are you sure?

> +
> +			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
> +
> +			status = "disabled";
> +		};
> +
> +		usb_1_ss0_qmpphy: phy@fd5000 {
> +			compatible = "qcom,x1e80100-qmp-usb3-dp-phy";
> +			reg = <0 0x00fd5000 0 0x4000>;
> +
> +			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
> +				 <&rpmhcc RPMH_CXO_CLK>,
> +				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
> +				 <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
> +			clock-names = "aux",
> +				      "ref",
> +				      "com_aux",
> +				      "usb3_pipe";
> +
> +			power-domains = <&gcc GCC_USB_0_PHY_GDSC>;

This is likely RPMHPD_MX(A/C)

[...]

> +			usb_1_ss2_dwc3: usb@a000000 {
> +				compatible = "snps,dwc3";
> +				reg = <0 0x0a000000 0 0xcd00>;
> +				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
> +				iommus = <&apps_smmu 0x14a0 0x0>;
> +				snps,dis_u2_susphy_quirk;
> +				snps,dis_enblslpm_quirk;
> +				snps,usb3_lpm_capable;
> +				phys = <&usb_1_ss2_hsphy>,
> +				       <&usb_1_ss2_qmpphy QMP_USB43DP_USB3_PHY>;
> +				phy-names = "usb2-phy",
> +				            "usb3-phy";

Should this be marked dma-coherent?

Konrad

Re: [PATCH v4 07/11] arm64: dts: qcom: x1e80100: Add PCIe nodes

[Konrad Dybcio]

On 1/23/24 12:01, Abel Vesa wrote:
> Add nodes for PCIe 4 and 6 controllers and their PHYs for X1E80100 platform.
> 
> Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
> Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
> Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
> Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---

[...]

> +
> +			interrupts = <GIC_SPI 773 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "msi";

You may want to add ITS MSIs too

[...]

> +
> +			resets = <&gcc GCC_PCIE_6A_BCR>,
> +				<&gcc GCC_PCIE_6A_LINK_DOWN_BCR>;

The second entry is misaligned

Konrad

Re: [PATCH v4 11/11] arm64: dts: qcom: x1e80100-qcp: Fix supplies for LDOs 3E and 2J

[Konrad Dybcio]

On 1/23/24 12:01, Abel Vesa wrote:
> The LDOs 3E and 2J are actually supplied by SMPS 5J. Fix accordingly.
> 
> Fixes: af16b00578a7 ("arm64: dts: qcom: Add base X1E80100 dtsi and the QCP dts")
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---

Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad

Re: [PATCH v4 04/11] arm64: dts: qcom: x1e80100: Add ADSP/CDSP remoteproc nodes

[Konrad Dybcio]

On 1/23/24 12:01, Abel Vesa wrote:
> From: Sibi Sankar <quic_sibis@quicinc.com>
> 
> Add ADSP and CDSP remoteproc nodes on X1E80100 platforms.
> 
> Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---

[...]

> +		remoteproc_cdsp: remoteproc@32300000 {
> +			compatible = "qcom,x1e80100-cdsp-pas";
> +			reg = <0 0x32300000 0 0x1400000>;
> +
> +			interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_EDGE_RISING>,

Is there no PDC mapping for this one?

Konrad

Re: [PATCH v4 02/11] arm64: dts: qcom: x1e80100: Add SMP2P nodes

[Konrad Dybcio]

On 1/23/24 12:01, Abel Vesa wrote:
> From: Sibi Sankar <quic_sibis@quicinc.com>
> 
> SMP2P is used for interrupting and being interrupted about remoteproc
> state changes related to the audio, compute and sensor subsystems.
> 
> Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad

Re: [PATCH v4 08/11] arm64: dts: qcom: x1e80100: Add display nodes

[Konrad Dybcio]

On 1/23/24 12:01, Abel Vesa wrote:
> Add the required nodes to support display on X1E80100.
> 
> Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
> Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
> Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
> Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>   arch/arm64/boot/dts/qcom/x1e80100.dtsi | 518 +++++++++++++++++++++++++++++++++
>   1 file changed, 518 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> index e8d2ea2b26ed..247ff7a9e405 100644
> --- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> +++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> @@ -4,6 +4,7 @@
>    */
>   
>   #include <dt-bindings/clock/qcom,rpmh.h>
> +#include <dt-bindings/clock/qcom,x1e80100-dispcc.h>
>   #include <dt-bindings/clock/qcom,x1e80100-gcc.h>
>   #include <dt-bindings/clock/qcom,x1e80100-tcsr.h>
>   #include <dt-bindings/dma/qcom-gpi.h>
> @@ -3298,6 +3299,523 @@ usb_1_ss1_role_switch: endpoint {
>   			};
>   		};
>   
> +		mdss: display-subsystem@ae00000 {
> +			compatible = "qcom,x1e80100-mdss";
> +			reg = <0 0x0ae00000 0 0x1000>;
> +			reg-names = "mdss";
> +
> +			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> +
> +			clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +				 <&gcc GCC_DISP_AHB_CLK>,
> +				 <&gcc GCC_DISP_HF_AXI_CLK>,
> +				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
> +
> +			resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
> +
> +			interconnects = <&mmss_noc MASTER_MDP QCOM_ICC_TAG_ALWAYS
> +					 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
> +					<&mc_virt MASTER_LLCC QCOM_ICC_TAG_ALWAYS
> +					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
> +			interconnect-names = "mdp0-mem",
> +					     "mdp1-mem";

You likely also want to add the cpu-cfg path

[...]

> +
> +		dispcc: clock-controller@af00000 {
> +			compatible = "qcom,x1e80100-dispcc";
> +			reg = <0 0x0af00000 0 0x20000>;
> +			clocks = <&bi_tcxo_div2>,
> +				 <&bi_tcxo_ao_div2>,
> +				 <&gcc GCC_DISP_AHB_CLK>,

This clock is not actually registered with the CCF.. Which means it's
also never cleanly shut down.. Please fix the clock driver and check
which others got omitted as well.

> +				 <&sleep_clk>,
> +				 <0>, /* dsi0 */
> +				 <0>,
> +				 <0>, /* dsi1 */
> +				 <0>,
> +				 <&usb_1_ss0_qmpphy QMP_USB43DP_DP_LINK_CLK>, /* dp0 */
> +				 <&usb_1_ss0_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>,
> +				 <&usb_1_ss1_qmpphy QMP_USB43DP_DP_LINK_CLK>, /* dp1 */
> +				 <&usb_1_ss1_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>,
> +				 <&mdss_dp2_phy 0>, /* dp2 */
> +				 <&mdss_dp2_phy 1>,
> +				 <&mdss_dp3_phy 0>, /* dp3 */
> +				 <&mdss_dp3_phy 1>;
> +			power-domains = <&rpmhpd RPMHPD_MMCX>;

Likely:

required-opps = <&rpmhpd_opp_low_svs>;

so that the PLLs have a chance to spin up

Konrad

Re: [PATCH v4 04/11] arm64: dts: qcom: x1e80100: Add ADSP/CDSP remoteproc nodes

[Abel Vesa]

On 24-01-23 19:22:35, Konrad Dybcio wrote:
> 
> 
> On 1/23/24 12:01, Abel Vesa wrote:
> > From: Sibi Sankar <quic_sibis@quicinc.com>
> > 
> > Add ADSP and CDSP remoteproc nodes on X1E80100 platforms.
> > 
> > Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
> > Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> > ---
> 
> [...]
> 
> > +		remoteproc_cdsp: remoteproc@32300000 {
> > +			compatible = "qcom,x1e80100-cdsp-pas";
> > +			reg = <0 0x32300000 0 0x1400000>;
> > +
> > +			interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_EDGE_RISING>,
> 
> Is there no PDC mapping for this one?
> 

Nope.

> Konrad

Re: [PATCH v4 04/11] arm64: dts: qcom: x1e80100: Add ADSP/CDSP remoteproc nodes

[Konrad Dybcio]

On 1/24/24 13:37, Abel Vesa wrote:
> On 24-01-23 19:22:35, Konrad Dybcio wrote:
>>
>>
>> On 1/23/24 12:01, Abel Vesa wrote:
>>> From: Sibi Sankar <quic_sibis@quicinc.com>
>>>
>>> Add ADSP and CDSP remoteproc nodes on X1E80100 platforms.
>>>
>>> Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
>>> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
>>> ---
>>
>> [...]
>>
>>> +		remoteproc_cdsp: remoteproc@32300000 {
>>> +			compatible = "qcom,x1e80100-cdsp-pas";
>>> +			reg = <0 0x32300000 0 0x1400000>;
>>> +
>>> +			interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_EDGE_RISING>,
>>
>> Is there no PDC mapping for this one?
>>
> 
> Nope.

Meh. Okay.


Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad

Re: [PATCH v4 08/11] arm64: dts: qcom: x1e80100: Add display nodes

[Abel Vesa]

On 24-01-23 19:36:17, Konrad Dybcio wrote:
> 
> 
> On 1/23/24 12:01, Abel Vesa wrote:
> > Add the required nodes to support display on X1E80100.
> > 
> > Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
> > Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
> > Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
> > Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
> > Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> > ---
> >   arch/arm64/boot/dts/qcom/x1e80100.dtsi | 518 +++++++++++++++++++++++++++++++++
> >   1 file changed, 518 insertions(+)
> > 
> > diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> > index e8d2ea2b26ed..247ff7a9e405 100644
> > --- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> > @@ -4,6 +4,7 @@
> >    */
> >   #include <dt-bindings/clock/qcom,rpmh.h>
> > +#include <dt-bindings/clock/qcom,x1e80100-dispcc.h>
> >   #include <dt-bindings/clock/qcom,x1e80100-gcc.h>
> >   #include <dt-bindings/clock/qcom,x1e80100-tcsr.h>
> >   #include <dt-bindings/dma/qcom-gpi.h>
> > @@ -3298,6 +3299,523 @@ usb_1_ss1_role_switch: endpoint {
> >   			};
> >   		};
> > +		mdss: display-subsystem@ae00000 {
> > +			compatible = "qcom,x1e80100-mdss";
> > +			reg = <0 0x0ae00000 0 0x1000>;
> > +			reg-names = "mdss";
> > +
> > +			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> > +
> > +			clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> > +				 <&gcc GCC_DISP_AHB_CLK>,
> > +				 <&gcc GCC_DISP_HF_AXI_CLK>,
> > +				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
> > +
> > +			resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
> > +
> > +			interconnects = <&mmss_noc MASTER_MDP QCOM_ICC_TAG_ALWAYS
> > +					 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
> > +					<&mc_virt MASTER_LLCC QCOM_ICC_TAG_ALWAYS
> > +					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
> > +			interconnect-names = "mdp0-mem",
> > +					     "mdp1-mem";
> 
> You likely also want to add the cpu-cfg path
> 
> [...]
> 
> > +
> > +		dispcc: clock-controller@af00000 {
> > +			compatible = "qcom,x1e80100-dispcc";
> > +			reg = <0 0x0af00000 0 0x20000>;
> > +			clocks = <&bi_tcxo_div2>,
> > +				 <&bi_tcxo_ao_div2>,
> > +				 <&gcc GCC_DISP_AHB_CLK>,
> 
> This clock is not actually registered with the CCF.. Which means it's
> also never cleanly shut down.. Please fix the clock driver and check
> which others got omitted as well.
> 

Right, so this clock is actually enabled on probe and is expected to be
always-on.

And I just noticed that at least on SM8[456]50 it's the same.

So I guess the solution here is to drop it from the dt node and fix the
dt schema. For all these platforms.

> > +				 <&sleep_clk>,
> > +				 <0>, /* dsi0 */
> > +				 <0>,
> > +				 <0>, /* dsi1 */
> > +				 <0>,
> > +				 <&usb_1_ss0_qmpphy QMP_USB43DP_DP_LINK_CLK>, /* dp0 */
> > +				 <&usb_1_ss0_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>,
> > +				 <&usb_1_ss1_qmpphy QMP_USB43DP_DP_LINK_CLK>, /* dp1 */
> > +				 <&usb_1_ss1_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>,
> > +				 <&mdss_dp2_phy 0>, /* dp2 */
> > +				 <&mdss_dp2_phy 1>,
> > +				 <&mdss_dp3_phy 0>, /* dp3 */
> > +				 <&mdss_dp3_phy 1>;
> > +			power-domains = <&rpmhpd RPMHPD_MMCX>;
> 
> Likely:
> 
> required-opps = <&rpmhpd_opp_low_svs>;
> 
> so that the PLLs have a chance to spin up
> 
> Konrad

Re: [PATCH v4 07/11] arm64: dts: qcom: x1e80100: Add PCIe nodes

[Abel Vesa]

On 24-01-23 19:20:38, Konrad Dybcio wrote:
> 
> 
> On 1/23/24 12:01, Abel Vesa wrote:
> > Add nodes for PCIe 4 and 6 controllers and their PHYs for X1E80100 platform.
> > 
> > Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
> > Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
> > Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
> > Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
> > Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> > ---
> 
> [...]
> 
> > +
> > +			interrupts = <GIC_SPI 773 IRQ_TYPE_LEVEL_HIGH>;
> > +			interrupt-names = "msi";
> 
> You may want to add ITS MSIs too

That will be added after we figure out the mapping.

> 
> [...]
> 
> > +
> > +			resets = <&gcc GCC_PCIE_6A_BCR>,
> > +				<&gcc GCC_PCIE_6A_LINK_DOWN_BCR>;
> 
> The second entry is misaligned
> 
> Konrad

Re: [PATCH v4 05/11] arm64: dts: qcom: x1e80100: Add TCSR node

[Abel Vesa]

On 24-01-23 19:09:37, Konrad Dybcio wrote:
> 
> 
> On 1/23/24 12:01, Abel Vesa wrote:
> > Add the TCSR clock controller and halt register space node.
> > 
> > Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> > ---
> 
> The former - yes, the latter - ?

Hm, so halt register space is at 0x1f60000. That would be in the mutex
region. But the mutex region is 0x20000 short, even on SM8650 and
SM8550. Need to see why is that, historically.

Either way, the tcsr node region still contains the regs needed by the
SCM driver to enable download mode. So I will rephrase this accordingly.

> 
> Konrad
> >   arch/arm64/boot/dts/qcom/x1e80100.dtsi | 8 ++++++++
> >   1 file changed, 8 insertions(+)
> > 
> > diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> > index be69e71b7f53..2b6c55a486b2 100644
> > --- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> > @@ -2606,6 +2606,14 @@ tcsr_mutex: hwlock@1f40000 {
> >   			#hwlock-cells = <1>;
> >   		};
> > +		tcsr: clock-controller@1fc0000 {
> > +			compatible = "qcom,x1e80100-tcsr", "syscon";
> > +			reg = <0 0x01fc0000 0 0x30000>;
> > +			clocks = <&rpmhcc RPMH_CXO_CLK>;
> > +			#clock-cells = <1>;
> > +			#reset-cells = <1>;
> > +		};
> > +
> >   		gem_noc: interconnect@26400000 {
> >   			compatible = "qcom,x1e80100-gem-noc";
> >   			reg = <0 0x26400000 0 0x311200>;
> > 

Re: [PATCH v4 06/11] arm64: dts: qcom: x1e80100: Add USB nodes

[Abel Vesa]

On 24-01-23 19:17:10, Konrad Dybcio wrote:
> 
> 
> On 1/23/24 12:01, Abel Vesa wrote:
> > Add nodes for all USB controllers and their PHYs for X1E80100 platform.
> > 
> > Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
> > Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
> > Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
> > Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
> > Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> > ---
> >   arch/arm64/boot/dts/qcom/x1e80100.dtsi | 435 ++++++++++++++++++++++++++++++++-
> >   1 file changed, 432 insertions(+), 3 deletions(-)
> > 
> > diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> > index 2b6c55a486b2..593ead89706c 100644
> > --- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> > @@ -5,11 +5,13 @@
> >   #include <dt-bindings/clock/qcom,rpmh.h>
> >   #include <dt-bindings/clock/qcom,x1e80100-gcc.h>
> > +#include <dt-bindings/clock/qcom,x1e80100-tcsr.h>
> >   #include <dt-bindings/dma/qcom-gpi.h>
> >   #include <dt-bindings/interconnect/qcom,icc.h>
> >   #include <dt-bindings/interconnect/qcom,x1e80100-rpmh.h>
> >   #include <dt-bindings/interrupt-controller/arm-gic.h>
> >   #include <dt-bindings/mailbox/qcom-ipcc.h>
> > +#include <dt-bindings/phy/phy-qcom-qmp.h>
> >   #include <dt-bindings/power/qcom,rpmhpd.h>
> >   #include <dt-bindings/power/qcom-rpmpd.h>
> >   #include <dt-bindings/soc/qcom,rpmh-rsc.h>
> > @@ -734,9 +736,9 @@ gcc: clock-controller@100000 {
> >   				 <0>,
> >   				 <0>,
> >   				 <0>,
> > -				 <0>,
> > -				 <0>,
> > -				 <0>;
> > +				 <&usb_1_ss0_qmpphy QMP_USB43DP_USB3_PIPE_CLK>,
> > +				 <&usb_1_ss1_qmpphy QMP_USB43DP_USB3_PIPE_CLK>,
> > +				 <&usb_1_ss2_qmpphy QMP_USB43DP_USB3_PIPE_CLK>;
> >   			power-domains = <&rpmhpd RPMHPD_CX>;
> >   			#clock-cells = <1>;
> > @@ -2492,6 +2494,126 @@ &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>,
> >   			};
> >   		};
> > +		usb_1_ss0_hsphy: phy@fd3000 {
> > +			compatible = "qcom,x1e80100-snps-eusb2-phy",
> > +				     "qcom,sm8550-snps-eusb2-phy";
> > +			reg = <0 0x00fd3000 0 0x154>;
> > +			#phy-cells = <0>;
> > +
> > +			clocks = <&tcsr TCSR_USB2_1_CLKREF_EN>;
> > +			clock-names = "ref";
> 
> You use this exact same clock for all HS PHYs. Are you sure?

The USB2 HS PHY should use TCSR_USB2_2_CLKREF_EN, while all of the USB1
SS[1-3] HS PHYs seems they share the TCSR_USB2_1_CLKREF_EN.

> 
> > +
> > +			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
> > +
> > +			status = "disabled";
> > +		};
> > +
> > +		usb_1_ss0_qmpphy: phy@fd5000 {
> > +			compatible = "qcom,x1e80100-qmp-usb3-dp-phy";
> > +			reg = <0 0x00fd5000 0 0x4000>;
> > +
> > +			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
> > +				 <&rpmhcc RPMH_CXO_CLK>,
> > +				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
> > +				 <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
> > +			clock-names = "aux",
> > +				      "ref",
> > +				      "com_aux",
> > +				      "usb3_pipe";
> > +
> > +			power-domains = <&gcc GCC_USB_0_PHY_GDSC>;
> 
> This is likely RPMHPD_MX(A/C)

Nope, this platform has dedicated GDSCs for each of the USB1 SS[1-3] QMP
PHYs.

> 
> [...]
> 
> > +			usb_1_ss2_dwc3: usb@a000000 {
> > +				compatible = "snps,dwc3";
> > +				reg = <0 0x0a000000 0 0xcd00>;
> > +				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
> > +				iommus = <&apps_smmu 0x14a0 0x0>;
> > +				snps,dis_u2_susphy_quirk;
> > +				snps,dis_enblslpm_quirk;
> > +				snps,usb3_lpm_capable;
> > +				phys = <&usb_1_ss2_hsphy>,
> > +				       <&usb_1_ss2_qmpphy QMP_USB43DP_USB3_PHY>;
> > +				phy-names = "usb2-phy",
> > +				            "usb3-phy";
> 
> Should this be marked dma-coherent?

Will add.

> 
> Konrad