Re: [PATCH v3] staging: dgnc: Fix Kconfig help header and text

[Mark Hounschell <markh@compro.net>]

On 10/1/18 12:49 PM, Lidza Louina wrote:
> On Mon, Oct 1, 2018 at 8:09 AM Mark Hounschell <markh@compro.net 
> <mailto:markh@compro.net>> wrote:
> 
>     On 9/28/18 3:59 PM, Lidza Louina wrote:
>      > I haven't done work on this driver in a long time. I looked up the
>      > devices, and they seem to already have an existing Linux driver:
>      >
>     https://www.digi.com/products/usb-and-serial-connectivity/serial-cards/digineo and
> 
>      > https://www.digi.com/support/productdetail?pid=1694
>      >
>      > I've contacted the company to see if the driver is still needed in
>      > staging. I'll send an update once they get back to me.
>      >
>      > Lidza
>      >
> 
>     Good luck with that. Digi obsoleted ALL their PCI serial cards several
>     months ago. They would not even respond to requests from me to include
>     their firmware for their PCI dgap cards into the kernel firmware
>     package. The card for the dgnc driver is a pci-e card that may still be
>     supported by them however. Also there does appear to be an already in
>     kernel driver for these "PCI-e" cards too. It actually works as I
>     have a
>     couple of these cards. The module name is "jsm".
> 
> 
>     03:00.0 Serial controller: Digi International Device 00f0 (rev 02)
>     (prog-if 02 [16550])
>               Subsystem: Digi International Device 00f0
>               Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
>     ParErr- Stepping- SERR- FastB2B- DisINTx-
>               Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>      >TAbort-
>     <TAbort- <MAbort- >SERR- <PERR- INTx-
>               Interrupt: pin A routed to IRQ 29
>               Region 0: Memory at f7200000 (32-bit, non-prefetchable)
>     [size=4K]
>               Capabilities: [40] Power Management version 2
>                       Flags: PMEClk+ DSI- D1- D2- AuxCurrent=0mA
>     PME(D0-,D1-,D2-,D3hot+,D3cold-)
>                       Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
>               Kernel driver in use: jsm
>               Kernel modules: jsm
> 
> 
>     Regards
>     Mark
> 
> 
> Thanks for the heads up Mark. I've totally neglected this driver and 
> should have caught this earlier. I'm okay with removing it from staging. 
> We can bring it back if they need it.
> 

It may actually be my fault that Greg-KH added the dgnc driver to 
staging. Shortly after Digi stopped supporting their PCI cards, I had 
some contact with Greg-KH and sent him all the Digi GPL drivers that I 
was using at the time for possible inclusion. Digi was no longer 
maintaining them. I did not know at the time about the jsm driver 
already being there.

The dgnc driver supports the following PCI cards:
#define PCI_DEVICE_CLASSIC_4_DID                0x0028
#define PCI_DEVICE_CLASSIC_8_DID                0x0029
#define PCI_DEVICE_CLASSIC_4_422_DID            0x00D0
#define PCI_DEVICE_CLASSIC_8_422_DID            0x00D1

The jsm driver supports all of these plus their newer PCI-e cards:
#define PCI_DEVICE_ID_CLASSIC_4         0x0028
#define PCI_DEVICE_ID_CLASSIC_8         0x0029
#define PCI_DEVICE_ID_CLASSIC_4_422     0x00D0
#define PCI_DEVICE_ID_CLASSIC_8_422     0x00D1

#define PCI_DEVICE_ID_NEO_4             0x00B0
#define PCI_DEVICE_ID_NEO_1_422         0x00CC
#define PCI_DEVICE_ID_NEO_1_422_485     0x00CD
#define PCI_DEVICE_ID_NEO_2_422_485     0x00CE
#define PCIE_DEVICE_ID_NEO_8            0x00F0
#define PCIE_DEVICE_ID_NEO_4            0x00F1
#define PCIE_DEVICE_ID_NEO_4RJ45        0x00F2
#define PCIE_DEVICE_ID_NEO_8RJ45        0x00F3

So I think it is safe to remove the dgnc driver from staging. I also 
think the PCI-e versions defined above are actually still available from 
Digi as current products.

Regards
Mark