* [PATCH] Fix cdrom error handling in 2.6
2003-08-23 0:48 Linux 2.6.0-test4 Linus Torvalds
@ 2003-08-23 1:21 ` Erik Andersen
2003-08-23 12:26 ` Linux 2.6.0-test4 vlad
` (7 subsequent siblings)
8 siblings, 0 replies; 20+ messages in thread
From: Erik Andersen @ 2003-08-23 1:21 UTC (permalink / raw)
To: Linus Torvalds; +Cc: Kernel Mailing List
In both 2.4 and in 2.6, error handling for bad cdrom media is
wrong. And it is my fault I'm afraid, since I botched an earlier
fix for the problem by putting the fix in the wrong spot.
My kids have a "Jumpstart Toddlers" cd they have long since
completely killed, which makes a great test disc. Without this
fix, the best time projection I can get for completing a dd type
sector copy is about 2 years... Most of that is spent thrashing
about in kernel space trying to re-read sectors we already know
are not correctable.... After the fix, I was able to rip a copy
the CD (or rather muddle through it getting lots of EIO errors)
in about 15 minutes.
Attached is the fix for 2.6.x,
-Erik
--
Erik B. Andersen http://codepoet-consulting.com/
--This message was written using 73% post-consumer electrons--
--- linux-2.6.0-test3/drivers/ide/ide-cd.c.orig 2003-08-22 19:04:36.000000000 -0600
+++ linux-2.6.0-test3/drivers/ide/ide-cd.c 2003-08-22 19:04:49.000000000 -0600
@@ -794,16 +794,16 @@
request or data protect error.*/
ide_dump_status (drive, "command error", stat);
do_end_request = 1;
- } else if ((err & ~ABRT_ERR) != 0) {
- /* Go to the default handler
- for other errors. */
- DRIVER(drive)->error(drive, "cdrom_decode_status",stat);
- return 1;
} else if (sense_key == MEDIUM_ERROR) {
/* No point in re-trying a zillion times on a bad
* sector... If we got here the error is not correctable */
ide_dump_status (drive, "media error (bad sector)", stat);
do_end_request = 1;
+ } else if ((err & ~ABRT_ERR) != 0) {
+ /* Go to the default handler
+ for other errors. */
+ DRIVER(drive)->error(drive, "cdrom_decode_status",stat);
+ return 1;
} else if ((++rq->errors > ERROR_MAX)) {
/* We've racked up too many retries. Abort. */
do_end_request = 1;
^ permalink raw reply [flat|nested] 20+ messages in thread
* RE: Linux 2.6.0-test4
2003-08-23 0:48 Linux 2.6.0-test4 Linus Torvalds
2003-08-23 1:21 ` [PATCH] Fix cdrom error handling in 2.6 Erik Andersen
@ 2003-08-23 12:26 ` vlad
2003-08-23 15:31 ` Jeff Garzik
2003-08-24 11:39 ` [PATCH] airo (was: Re: Linux 2.6.0-test4) Geert Uytterhoeven
` (6 subsequent siblings)
8 siblings, 1 reply; 20+ messages in thread
From: vlad @ 2003-08-23 12:26 UTC (permalink / raw)
To: 'Linus Torvalds', 'Kernel Mailing List'
Getting this compile problem during modules_install, will paste in .config
after the depmod errors:
if [ -r System.map ]; then /sbin/depmod -ae -F System.map 2.6.0-test4; fi
depmod: *** Unresolved symbols in
/lib/modules/2.6.0-test4/kernel/drivers/block/cryptoloop.ko
depmod: loop_register_transfer
depmod: loop_unregister_transfer
depmod: *** Unresolved symbols in
/lib/modules/2.6.0-test4/kernel/sound/oss/ac97_plugin_ad1980.ko
depmod: ac97_unregister_driver
depmod: ac97_register_driver
depmod: *** Unresolved symbols in
/lib/modules/2.6.0-test4/kernel/sound/oss/ad1889.ko
depmod: ac97_probe_codec
depmod: ac97_alloc_codec
depmod: ac97_read_proc
depmod: ac97_release_codec
depmod: *** Unresolved symbols in
/lib/modules/2.6.0-test4/kernel/sound/oss/ali5455.ko
depmod: ac97_probe_codec
depmod: ac97_alloc_codec
depmod: ac97_set_dac_rate
depmod: ac97_set_adc_rate
depmod: ac97_release_codec
depmod: *** Unresolved symbols in
/lib/modules/2.6.0-test4/kernel/sound/oss/forte.ko
depmod: ac97_probe_codec
depmod: ac97_alloc_codec
depmod: ac97_read_proc
depmod: ac97_release_codec
.config:
#
# Automatically generated make config: don't edit
#
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_GENERIC_ISA_DMA=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
# CONFIG_BROKEN is not set
#
# General setup
#
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_SYSCTL=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
# CONFIG_EMBEDDED is not set
CONFIG_KALLSYMS=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_OBSOLETE_MODPARM=y
CONFIG_MODVERSIONS=y
CONFIG_KMOD=y
#
# Processor type and features
#
CONFIG_X86_PC=y
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
# CONFIG_X86_GENERICARCH is not set
# CONFIG_X86_ES7000 is not set
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
CONFIG_M586MMX=y
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MK8 is not set
# CONFIG_MELAN is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_X86_GENERIC is not set
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_L1_CACHE_SHIFT=5
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_X86_PPRO_FENCE=y
CONFIG_X86_F00F_BUG=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_ALIGNMENT_16=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_SMP is not set
CONFIG_PREEMPT=y
# CONFIG_X86_UP_APIC is not set
CONFIG_X86_TSC=y
CONFIG_X86_MCE=y
# CONFIG_X86_MCE_NONFATAL is not set
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
# CONFIG_MICROCODE is not set
# CONFIG_X86_MSR is not set
# CONFIG_X86_CPUID is not set
CONFIG_EDD=y
CONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
CONFIG_HAVE_DEC_LOCK=y
#
# Power management options (ACPI, APM)
#
# CONFIG_PM is not set
#
# ACPI (Advanced Configuration and Power Interface) Support
#
CONFIG_ACPI_HT=y
CONFIG_ACPI=y
CONFIG_ACPI_BOOT=y
CONFIG_ACPI_AC=y
CONFIG_ACPI_BATTERY=y
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_FAN=y
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_THERMAL=y
# CONFIG_ACPI_ASUS is not set
# CONFIG_ACPI_TOSHIBA is not set
CONFIG_ACPI_DEBUG=y
CONFIG_ACPI_BUS=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_PCI=y
CONFIG_ACPI_SYSTEM=y
#
# CPU Frequency scaling
#
# CONFIG_CPU_FREQ is not set
#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_LEGACY_PROC=y
CONFIG_PCI_NAMES=y
CONFIG_ISA=y
# CONFIG_EISA is not set
# CONFIG_MCA is not set
# CONFIG_SCx200 is not set
# CONFIG_HOTPLUG is not set
#
# Executable file formats
#
CONFIG_KCORE_ELF=y
# CONFIG_KCORE_AOUT is not set
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_AOUT=y
CONFIG_BINFMT_MISC=y
#
# Generic Driver Options
#
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
CONFIG_PARPORT=y
CONFIG_PARPORT_PC=y
CONFIG_PARPORT_PC_CML1=y
# CONFIG_PARPORT_SERIAL is not set
# CONFIG_PARPORT_PC_FIFO is not set
# CONFIG_PARPORT_PC_SUPERIO is not set
# CONFIG_PARPORT_OTHER is not set
CONFIG_PARPORT_1284=y
#
# Plug and Play support
#
CONFIG_PNP=y
CONFIG_PNP_DEBUG=y
#
# Protocols
#
# CONFIG_ISAPNP is not set
# CONFIG_PNPBIOS is not set
#
# Block devices
#
CONFIG_BLK_DEV_FD=y
# CONFIG_BLK_DEV_XD is not set
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
CONFIG_BLK_DEV_LOOP=m
CONFIG_BLK_DEV_CRYPTOLOOP=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_RAM=m
CONFIG_BLK_DEV_RAM_SIZE=7777
# CONFIG_BLK_DEV_INITRD is not set
CONFIG_LBD=y
#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
CONFIG_IDEDISK_STROKE=y
CONFIG_BLK_DEV_IDECD=y
CONFIG_BLK_DEV_IDETAPE=m
# CONFIG_BLK_DEV_IDEFLOPPY is not set
CONFIG_BLK_DEV_IDESCSI=y
CONFIG_IDE_TASK_IOCTL=y
CONFIG_IDE_TASKFILE_IO=y
#
# IDE chipset support/bugfixes
#
CONFIG_BLK_DEV_CMD640=y
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
# CONFIG_BLK_DEV_IDEPNP is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
CONFIG_BLK_DEV_RZ1000=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDE_TCQ is not set
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_IDEDMA_PCI_WIP is not set
CONFIG_BLK_DEV_ADMA=y
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_SC1200 is not set
CONFIG_BLK_DEV_PIIX=y
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_CHIPSETS is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_DMA_NONPCI is not set
# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
#
CONFIG_SCSI=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
CONFIG_CHR_DEV_ST=y
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=y
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=y
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_REPORT_LUNS=y
CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set
#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AACRAID is not set
CONFIG_SCSI_AIC7XXX=y
CONFIG_AIC7XXX_CMDS_PER_DEVICE=64
CONFIG_AIC7XXX_RESET_DELAY_MS=2000
# CONFIG_AIC7XXX_PROBE_EISA_VL is not set
# CONFIG_AIC7XXX_BUILD_FIRMWARE is not set
# CONFIG_AIC7XXX_DEBUG_ENABLE is not set
CONFIG_AIC7XXX_DEBUG_MASK=0
CONFIG_AIC7XXX_REG_PRETTY_PRINT=y
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_AM53C974 is not set
# CONFIG_SCSI_MEGARAID is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_CPQFCTS is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_SYM53C8XX is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PCI2000 is not set
# CONFIG_SCSI_PCI2220I is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
CONFIG_SCSI_QLOGIC_1280=y
# CONFIG_SCSI_SEAGATE is not set
# CONFIG_SCSI_SYM53C416 is not set
CONFIG_SCSI_DC395x=m
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
#
# Old CD-ROM drivers (not SCSI, not IDE)
#
# CONFIG_CD_NO_IDESCSI is not set
#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support (EXPERIMENTAL)
#
# CONFIG_IEEE1394 is not set
#
# I2O device support
#
# CONFIG_I2O is not set
#
# Networking support
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
# CONFIG_NETLINK_DEV is not set
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
# CONFIG_IP_PNP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
# CONFIG_INET_ECN is not set
# CONFIG_SYN_COOKIES is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
CONFIG_INET_IPCOMP=m
# CONFIG_IPV6 is not set
# CONFIG_DECNET is not set
# CONFIG_BRIDGE is not set
# CONFIG_NETFILTER is not set
CONFIG_XFRM=y
# CONFIG_XFRM_USER is not set
#
# SCTP Configuration (EXPERIMENTAL)
#
CONFIG_IPV6_SCTP__=y
# CONFIG_IP_SCTP is not set
# CONFIG_ATM is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_LLC is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_FASTROUTE is not set
# CONFIG_NET_HW_FLOWCONTROL is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
CONFIG_NETDEVICES=y
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
CONFIG_DUMMY=y
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_ETHERTAP is not set
# CONFIG_NET_SB1000 is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=m
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set
#
# Tulip family network device support
#
# CONFIG_NET_TULIP is not set
# CONFIG_AT1700 is not set
# CONFIG_DEPCA is not set
# CONFIG_HP100 is not set
# CONFIG_NET_ISA is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_AC3200 is not set
# CONFIG_APRICOT is not set
# CONFIG_B44 is not set
# CONFIG_CS89x0 is not set
# CONFIG_DGRS is not set
CONFIG_EEPRO100=y
# CONFIG_EEPRO100_PIO is not set
# CONFIG_E100 is not set
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_8139CP is not set
# CONFIG_8139TOO is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_NET_POCKET is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SIS190 is not set
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set
#
# Ethernet (10000 Mbit)
#
CONFIG_IXGB=m
# CONFIG_IXGB_NAPI is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
CONFIG_PLIP=y
CONFIG_PPP=y
CONFIG_PPP_MULTILINK=y
# CONFIG_PPP_FILTER is not set
CONFIG_PPP_ASYNC=y
CONFIG_PPP_SYNC_TTY=y
CONFIG_PPP_DEFLATE=y
CONFIG_PPP_BSDCOMP=y
CONFIG_PPPOE=y
CONFIG_SLIP=y
CONFIG_SLIP_COMPRESSED=y
# CONFIG_SLIP_SMART is not set
# CONFIG_SLIP_MODE_SLIP6 is not set
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Token Ring devices (depends on LLC=y)
#
# CONFIG_NET_FC is not set
# CONFIG_RCPCI is not set
# CONFIG_SHAPER is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
#
# Amateur Radio support
#
# CONFIG_HAMRADIO is not set
#
# IrDA (infrared) support
#
# CONFIG_IRDA is not set
#
# ISDN subsystem
#
# CONFIG_ISDN_BOOL is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
#
# Input device support
#
CONFIG_INPUT=y
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_EVBUG is not set
#
# Input I/O drivers
#
# CONFIG_GAMEPORT is not set
CONFIG_SOUND_GAMEPORT=y
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PARKBD is not set
CONFIG_SERIO_PCIPS2=m
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_INPORT is not set
# CONFIG_MOUSE_LOGIBM is not set
# CONFIG_MOUSE_PC110PAD is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_SERIAL_NONSTANDARD is not set
#
# Serial drivers
#
CONFIG_SERIAL_8250=y
# CONFIG_SERIAL_8250_CONSOLE is not set
CONFIG_SERIAL_8250_ACPI=y
# CONFIG_SERIAL_8250_EXTENDED is not set
#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_UNIX98_PTYS=y
CONFIG_UNIX98_PTY_COUNT=256
CONFIG_PRINTER=y
# CONFIG_LP_CONSOLE is not set
# CONFIG_PPDEV is not set
# CONFIG_TIPAR is not set
#
# I2C support
#
# CONFIG_I2C is not set
#
# I2C Hardware Sensors Mainboard support
#
#
# I2C Hardware Sensors Chip support
#
# CONFIG_I2C_SENSOR is not set
#
# Mice
#
# CONFIG_BUSMOUSE is not set
# CONFIG_QIC02_TAPE is not set
#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
CONFIG_NVRAM=y
# CONFIG_RTC is not set
# CONFIG_GEN_RTC is not set
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
CONFIG_AGP=y
CONFIG_AGP_ALI=y
CONFIG_AGP_ATI=y
CONFIG_AGP_AMD=y
# CONFIG_AGP_AMD_8151 is not set
CONFIG_AGP_INTEL=y
# CONFIG_AGP_NVIDIA is not set
CONFIG_AGP_SIS=y
CONFIG_AGP_SWORKS=y
CONFIG_AGP_VIA=y
CONFIG_DRM=y
# CONFIG_DRM_TDFX is not set
# CONFIG_DRM_GAMMA is not set
# CONFIG_DRM_R128 is not set
CONFIG_DRM_RADEON=y
# CONFIG_DRM_I810 is not set
# CONFIG_DRM_I830 is not set
# CONFIG_DRM_MGA is not set
# CONFIG_MWAVE is not set
# CONFIG_RAW_DRIVER is not set
CONFIG_HANGCHECK_TIMER=m
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
# CONFIG_EXT2_FS_POSIX_ACL is not set
# CONFIG_EXT2_FS_SECURITY is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
# CONFIG_EXT3_FS_SECURITY is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
CONFIG_REISERFS_FS=y
CONFIG_REISERFS_CHECK=y
CONFIG_REISERFS_PROC_INFO=y
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_QUOTA=y
CONFIG_QFMT_V1=m
CONFIG_QFMT_V2=m
CONFIG_QUOTACTL=y
CONFIG_AUTOFS_FS=y
CONFIG_AUTOFS4_FS=y
#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
# CONFIG_ZISOFS is not set
CONFIG_UDF_FS=y
#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_NTFS_FS=y
CONFIG_NTFS_DEBUG=y
# CONFIG_NTFS_RW is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
# CONFIG_DEVFS_FS is not set
CONFIG_DEVPTS_FS=y
# CONFIG_DEVPTS_FS_XATTR is not set
CONFIG_TMPFS=y
CONFIG_RAMFS=y
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
CONFIG_UFS_FS=y
# CONFIG_UFS_FS_WRITE is not set
#
# Network File Systems
#
CONFIG_NFS_FS=y
# CONFIG_NFS_V3 is not set
# CONFIG_NFS_V4 is not set
CONFIG_NFSD=y
# CONFIG_NFSD_V3 is not set
# CONFIG_NFSD_TCP is not set
CONFIG_LOCKD=y
CONFIG_EXPORTFS=y
CONFIG_SUNRPC=y
# CONFIG_SUNRPC_GSS is not set
CONFIG_SMB_FS=y
CONFIG_SMB_NLS_DEFAULT=y
CONFIG_SMB_NLS_REMOTE="cp437"
CONFIG_CIFS=y
CONFIG_NCP_FS=y
CONFIG_NCPFS_PACKET_SIGNING=y
CONFIG_NCPFS_IOCTL_LOCKING=y
CONFIG_NCPFS_STRONG=y
CONFIG_NCPFS_NFS_NS=y
CONFIG_NCPFS_OS2_NS=y
CONFIG_NCPFS_SMALLDOS=y
CONFIG_NCPFS_NLS=y
CONFIG_NCPFS_EXTRAS=y
# CONFIG_CODA_FS is not set
# CONFIG_INTERMEZZO_FS is not set
# CONFIG_AFS_FS is not set
#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
# CONFIG_OSF_PARTITION is not set
# CONFIG_AMIGA_PARTITION is not set
# CONFIG_ATARI_PARTITION is not set
# CONFIG_MAC_PARTITION is not set
CONFIG_MSDOS_PARTITION=y
CONFIG_BSD_DISKLABEL=y
# CONFIG_MINIX_SUBPARTITION is not set
CONFIG_SOLARIS_X86_PARTITION=y
# CONFIG_UNIXWARE_DISKLABEL is not set
CONFIG_LDM_PARTITION=y
CONFIG_LDM_DEBUG=y
# CONFIG_NEC98_PARTITION is not set
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
CONFIG_SMB_NLS=y
CONFIG_NLS=y
#
# Native Language Support
#
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_852=m
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
CONFIG_NLS_ISO8859_1=y
CONFIG_NLS_ISO8859_2=m
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
CONFIG_NLS_UTF8=y
#
# Graphics support
#
# CONFIG_FB is not set
# CONFIG_VIDEO_SELECT is not set
#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
# CONFIG_MDA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
#
# Sound
#
CONFIG_SOUND=y
#
# Advanced Linux Sound Architecture
#
CONFIG_SND=y
CONFIG_SND_SEQUENCER=y
# CONFIG_SND_SEQ_DUMMY is not set
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=y
CONFIG_SND_PCM_OSS=y
CONFIG_SND_SEQUENCER_OSS=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
#
# Generic devices
#
# CONFIG_SND_DUMMY is not set
# CONFIG_SND_VIRMIDI is not set
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set
#
# ISA devices
#
# CONFIG_SND_AD1848 is not set
# CONFIG_SND_CS4231 is not set
# CONFIG_SND_CS4232 is not set
# CONFIG_SND_CS4236 is not set
# CONFIG_SND_ES1688 is not set
# CONFIG_SND_ES18XX is not set
# CONFIG_SND_GUSCLASSIC is not set
# CONFIG_SND_GUSEXTREME is not set
# CONFIG_SND_GUSMAX is not set
# CONFIG_SND_INTERWAVE is not set
# CONFIG_SND_INTERWAVE_STB is not set
# CONFIG_SND_OPTI92X_AD1848 is not set
# CONFIG_SND_OPTI92X_CS4231 is not set
# CONFIG_SND_OPTI93X is not set
# CONFIG_SND_SB8 is not set
# CONFIG_SND_SB16 is not set
# CONFIG_SND_SBAWE is not set
# CONFIG_SND_WAVEFRONT is not set
# CONFIG_SND_CMI8330 is not set
# CONFIG_SND_OPL3SA2 is not set
# CONFIG_SND_SGALAXY is not set
# CONFIG_SND_SSCAPE is not set
#
# PCI devices
#
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_EMU10K1 is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_YMFPCI is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_FM801 is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
CONFIG_SND_INTEL8X0=y
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VX222 is not set
#
# ALSA USB devices
#
# CONFIG_SND_USB_AUDIO is not set
#
# Open Sound System
#
CONFIG_SOUND_PRIME=y
# CONFIG_SOUND_BT878 is not set
# CONFIG_SOUND_CMPCI is not set
# CONFIG_SOUND_EMU10K1 is not set
# CONFIG_SOUND_FUSION is not set
# CONFIG_SOUND_CS4281 is not set
# CONFIG_SOUND_ES1370 is not set
# CONFIG_SOUND_ES1371 is not set
# CONFIG_SOUND_ESSSOLO1 is not set
# CONFIG_SOUND_MAESTRO is not set
# CONFIG_SOUND_MAESTRO3 is not set
# CONFIG_SOUND_ICH is not set
# CONFIG_SOUND_RME96XX is not set
# CONFIG_SOUND_SONICVIBES is not set
# CONFIG_SOUND_TRIDENT is not set
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
# CONFIG_SOUND_VIA82CXXX is not set
CONFIG_SOUND_OSS=y
# CONFIG_SOUND_TRACEINIT is not set
# CONFIG_SOUND_DMAP is not set
CONFIG_SOUND_AD1816=y
CONFIG_SOUND_AD1889=m
# CONFIG_SOUND_SGALAXY is not set
# CONFIG_SOUND_ADLIB is not set
# CONFIG_SOUND_ACI_MIXER is not set
# CONFIG_SOUND_CS4232 is not set
# CONFIG_SOUND_SSCAPE is not set
# CONFIG_SOUND_GUS is not set
# CONFIG_SOUND_VMIDI is not set
# CONFIG_SOUND_TRIX is not set
# CONFIG_SOUND_MSS is not set
# CONFIG_SOUND_MPU401 is not set
# CONFIG_SOUND_NM256 is not set
# CONFIG_SOUND_MAD16 is not set
# CONFIG_SOUND_PAS is not set
# CONFIG_SOUND_PSS is not set
# CONFIG_SOUND_SB is not set
# CONFIG_SOUND_AWE32_SYNTH is not set
# CONFIG_SOUND_WAVEFRONT is not set
# CONFIG_SOUND_MAUI is not set
# CONFIG_SOUND_YM3812 is not set
# CONFIG_SOUND_OPL3SA1 is not set
# CONFIG_SOUND_OPL3SA2 is not set
# CONFIG_SOUND_YMFPCI is not set
# CONFIG_SOUND_UART6850 is not set
# CONFIG_SOUND_AEDSP16 is not set
CONFIG_SOUND_ALI5455=m
CONFIG_SOUND_FORTE=m
CONFIG_SOUND_AD1980=m
#
# USB support
#
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
CONFIG_USB_BANDWIDTH=y
# CONFIG_USB_DYNAMIC_MINORS is not set
#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=y
# CONFIG_USB_OHCI_HCD is not set
CONFIG_USB_UHCI_HCD=y
#
# USB Device Class drivers
#
# CONFIG_USB_AUDIO is not set
# CONFIG_USB_BLUETOOTH_TTY is not set
# CONFIG_USB_MIDI is not set
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
CONFIG_USB_STORAGE=y
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_DPCM is not set
# CONFIG_USB_STORAGE_HP8200e is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
#
# USB Human Interface Devices (HID)
#
# CONFIG_USB_HID is not set
#
# USB HID Boot Protocol drivers
#
# CONFIG_USB_KBD is not set
# CONFIG_USB_MOUSE is not set
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_XPAD is not set
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_SCANNER is not set
# CONFIG_USB_MICROTEK is not set
# CONFIG_USB_HPUSBSCSI is not set
#
# USB Multimedia devices
#
# CONFIG_USB_DABUSB is not set
#
# Video4Linux support is needed for USB Multimedia device support
#
#
# USB Network adaptors
#
CONFIG_USB_AX8817X=m
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET is not set
#
# USB port drivers
#
# CONFIG_USB_USS720 is not set
#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set
#
# USB Miscellaneous drivers
#
# CONFIG_USB_TIGL is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_BRLVGER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_TEST is not set
# CONFIG_USB_GADGET is not set
#
# Bluetooth support
#
# CONFIG_BT is not set
#
# Profiling support
#
CONFIG_PROFILING=y
CONFIG_OPROFILE=y
#
# Kernel hacking
#
# CONFIG_DEBUG_KERNEL is not set
CONFIG_DEBUG_SPINLOCK_SLEEP=y
CONFIG_FRAME_POINTER=y
#
# Security options
#
CONFIG_SECURITY=y
# CONFIG_SECURITY_NETWORK is not set
CONFIG_SECURITY_CAPABILITIES=y
CONFIG_SECURITY_ROOTPLUG=y
# CONFIG_SECURITY_SELINUX is not set
#
# Cryptographic options
#
CONFIG_CRYPTO=y
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=m
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_DES=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_SERPENT=m
CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_CAST5=m
CONFIG_CRYPTO_CAST6=m
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRYPTO_TEST=m
#
# Library routines
#
CONFIG_CRC32=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_X86_BIOS_REBOOT=y
--
/"\ / For information and quotes, email us at
\ / ASCII RIBBON CAMPAIGN / info@lrsehosting.com
X AGAINST HTML MAIL / http://www.lrsehosting.com/
/ \ AND POSTINGS / vlad@lrsehosting.com
-------------------------------------------------------------------------
-----Original Message-----
From: linux-kernel-owner@vger.kernel.org
[mailto:linux-kernel-owner@vger.kernel.org]On Behalf Of Linus Torvalds
Sent: Friday, August 22, 2003 7:49 PM
To: Kernel Mailing List
Subject: Linux 2.6.0-test4
There should be a lot of compile fixes here, along with updates for ia64,
and the (painful) move of the 'name' entry out of the "struct device" that
helps avoid unnecessary memory waste.
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Linux 2.6.0-test4
2003-08-23 12:26 ` Linux 2.6.0-test4 vlad
@ 2003-08-23 15:31 ` Jeff Garzik
2003-08-23 15:33 ` William Scott Lockwood III
2003-08-25 5:43 ` vlad
0 siblings, 2 replies; 20+ messages in thread
From: Jeff Garzik @ 2003-08-23 15:31 UTC (permalink / raw)
To: vlad; +Cc: 'Linus Torvalds', 'Kernel Mailing List'
On Sat, Aug 23, 2003 at 07:26:45AM -0500, vlad@lrsehosting.com wrote:
> Getting this compile problem during modules_install, will paste in .config
> after the depmod errors:
Looks like you need new modutils...
Jeff
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Linux 2.6.0-test4
2003-08-23 15:31 ` Jeff Garzik
@ 2003-08-23 15:33 ` William Scott Lockwood III
2003-08-25 5:43 ` vlad
1 sibling, 0 replies; 20+ messages in thread
From: William Scott Lockwood III @ 2003-08-23 15:33 UTC (permalink / raw)
To: jgarzik; +Cc: vlad, torvalds, linux-kernel
> On Sat, Aug 23, 2003 at 07:26:45AM -0500, vlad@lrsehosting.com wrote:
>> Getting this compile problem during modules_install, will paste in
>> .config after the depmod errors:
>
> Looks like you need new modutils...
>
> Jeff
I just updated them, when test3 came out. Was there another release?
-----------------------------------------
This email was sent using SquirrelMail.
"Webmail for nuts!"
http://squirrelmail.org/
^ permalink raw reply [flat|nested] 20+ messages in thread
* RE: Linux 2.6.0-test4
2003-08-23 15:31 ` Jeff Garzik
2003-08-23 15:33 ` William Scott Lockwood III
@ 2003-08-25 5:43 ` vlad
1 sibling, 0 replies; 20+ messages in thread
From: vlad @ 2003-08-25 5:43 UTC (permalink / raw)
To: 'Jeff Garzik', 'Kernel Mailing List'
Cc: 'Linus Torvalds'
As a follow up to this, I downloaded and installed modutils and module init
tools, the latest versions available on kernel.org, did:
./configure
make all install
And I still get the same error as I was getting before. Is there somewhere
else I'm supposed to be looking, or did I miss a step building modutils and
module init tools?
Scott
--
-----Original Message-----
From: Jeff Garzik [mailto:jgarzik@pobox.com]
Sent: Saturday, August 23, 2003 10:32 AM
To: vlad@lrsehosting.com
Cc: 'Linus Torvalds'; 'Kernel Mailing List'
Subject: Re: Linux 2.6.0-test4
On Sat, Aug 23, 2003 at 07:26:45AM -0500, vlad@lrsehosting.com wrote:
> Getting this compile problem during modules_install, will paste in .config
> after the depmod errors:
Looks like you need new modutils...
Jeff
^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH] airo (was: Re: Linux 2.6.0-test4)
2003-08-23 0:48 Linux 2.6.0-test4 Linus Torvalds
2003-08-23 1:21 ` [PATCH] Fix cdrom error handling in 2.6 Erik Andersen
2003-08-23 12:26 ` Linux 2.6.0-test4 vlad
@ 2003-08-24 11:39 ` Geert Uytterhoeven
2003-08-24 21:00 ` Javier Achirica
2003-08-24 11:47 ` [PATCH] vmlinux-*.lds " Geert Uytterhoeven
` (5 subsequent siblings)
8 siblings, 1 reply; 20+ messages in thread
From: Geert Uytterhoeven @ 2003-08-24 11:39 UTC (permalink / raw)
To: Javier Achirica; +Cc: Linus Torvalds, Andrew Morton, Linux Kernel Development
On Fri, 22 Aug 2003, Linus Torvalds wrote:
> Javier Achirica:
> o [wireless airo] Fix PCI unregister code
This patch causes a regression: if CONFIG_PCI is not set, it doesn't compile
anymore. Here's a fix. I also killed a dead variable and its corresponding
warning:
--- linux-2.6.0-test4/drivers/net/wireless/airo.c Sun Aug 24 09:49:30 2003
+++ linux-m68k-2.6.0-test4/drivers/net/wireless/airo.c Sun Aug 24 13:03:56 2003
@@ -4156,7 +4156,7 @@
static int __init airo_init_module( void )
{
- int i, rc = 0, have_isa_dev = 0;
+ int i, have_isa_dev = 0;
airo_entry = create_proc_entry("aironet",
S_IFDIR | airo_perm,
@@ -4174,7 +4174,7 @@
#ifdef CONFIG_PCI
printk( KERN_INFO "airo: Probing for PCI adapters\n" );
- rc = pci_module_init(&airo_driver);
+ pci_module_init(&airo_driver);
printk( KERN_INFO "airo: Finished probing for PCI adapters\n" );
#endif
@@ -4197,8 +4197,11 @@
}
remove_proc_entry("aironet", proc_root_driver);
- if (is_pci)
+ if (is_pci) {
+#ifdef CONFIG_PCI
pci_unregister_driver(&airo_driver);
+#endif
+ }
}
#ifdef WIRELESS_EXT
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH] airo (was: Re: Linux 2.6.0-test4)
2003-08-24 11:39 ` [PATCH] airo (was: Re: Linux 2.6.0-test4) Geert Uytterhoeven
@ 2003-08-24 21:00 ` Javier Achirica
0 siblings, 0 replies; 20+ messages in thread
From: Javier Achirica @ 2003-08-24 21:00 UTC (permalink / raw)
To: Geert Uytterhoeven
Cc: Linus Torvalds, Andrew Morton, Linux Kernel Development
Thank you. There's also another small PCI bug. I'll submit a patch to
Jeff.
Javier Achirica
On Sun, 24 Aug 2003, Geert Uytterhoeven wrote:
> On Fri, 22 Aug 2003, Linus Torvalds wrote:
> > Javier Achirica:
> > o [wireless airo] Fix PCI unregister code
>
> This patch causes a regression: if CONFIG_PCI is not set, it doesn't compile
> anymore. Here's a fix. I also killed a dead variable and its corresponding
> warning:
>
> --- linux-2.6.0-test4/drivers/net/wireless/airo.c Sun Aug 24 09:49:30 2003
> +++ linux-m68k-2.6.0-test4/drivers/net/wireless/airo.c Sun Aug 24 13:03:56 2003
> @@ -4156,7 +4156,7 @@
>
> static int __init airo_init_module( void )
> {
> - int i, rc = 0, have_isa_dev = 0;
> + int i, have_isa_dev = 0;
>
> airo_entry = create_proc_entry("aironet",
> S_IFDIR | airo_perm,
> @@ -4174,7 +4174,7 @@
>
> #ifdef CONFIG_PCI
> printk( KERN_INFO "airo: Probing for PCI adapters\n" );
> - rc = pci_module_init(&airo_driver);
> + pci_module_init(&airo_driver);
> printk( KERN_INFO "airo: Finished probing for PCI adapters\n" );
> #endif
>
> @@ -4197,8 +4197,11 @@
> }
> remove_proc_entry("aironet", proc_root_driver);
>
> - if (is_pci)
> + if (is_pci) {
> +#ifdef CONFIG_PCI
> pci_unregister_driver(&airo_driver);
> +#endif
> + }
> }
>
> #ifdef WIRELESS_EXT
>
> Gr{oetje,eeting}s,
>
> Geert
>
> --
> Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
>
> In personal conversations with technical people, I call myself a hacker. But
> when I'm talking to journalists I just say "programmer" or something like that.
> -- Linus Torvalds
>
>
>
>
^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH] vmlinux-*.lds (was: Re: Linux 2.6.0-test4)
2003-08-23 0:48 Linux 2.6.0-test4 Linus Torvalds
` (2 preceding siblings ...)
2003-08-24 11:39 ` [PATCH] airo (was: Re: Linux 2.6.0-test4) Geert Uytterhoeven
@ 2003-08-24 11:47 ` Geert Uytterhoeven
2003-08-24 11:51 ` [PATCH] macide " Geert Uytterhoeven
` (4 subsequent siblings)
8 siblings, 0 replies; 20+ messages in thread
From: Geert Uytterhoeven @ 2003-08-24 11:47 UTC (permalink / raw)
To: Kai Germaschewski; +Cc: Linus Torvalds, Andrew Morton, Linux Kernel Development
On Fri, 22 Aug 2003, Linus Torvalds wrote:
> Kai Germaschewski:
> o kbuild: Move generation of vmlinux.lds.s into arch/.../kernel
You forgot to move two files:
mv arch/m68k/vmlinux-std.lds arch/m68k/kernel
mv arch/m68k/vmlinux-sun3.lds arch/m68k/kernel
Or apply this patch:
--- linux-2.6.0-test4/arch/m68k/vmlinux-std.lds Sun Jun 15 09:37:32 2003
+++ linux-m68k-2.6.0-test4/arch/m68k/vmlinux-std.lds Tue Jun 24 14:30:53 2003
@@ -1,97 +0,0 @@
-/* ld script to make m68k Linux kernel */
-
-#include <asm-generic/vmlinux.lds.h>
-
-OUTPUT_FORMAT("elf32-m68k", "elf32-m68k", "elf32-m68k")
-OUTPUT_ARCH(m68k)
-ENTRY(_start)
-jiffies = jiffies_64 + 4;
-SECTIONS
-{
- . = 0x1000;
- _text = .; /* Text and read-only data */
- .text : {
- *(.text)
- *(.fixup)
- *(.gnu.warning)
- } = 0x4e75
-
- . = ALIGN(16); /* Exception table */
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- RODATA
-
- _etext = .; /* End of text section */
-
- .data : { /* Data */
- *(.data)
- CONSTRUCTORS
- }
-
- .bss : { *(.bss) } /* BSS */
-
- . = ALIGN(16);
- .data.cacheline_aligned : { *(.data.cacheline_aligned) }
-
- _edata = .; /* End of data section */
-
- /* will be freed after init */
- . = ALIGN(4096); /* Init code and data */
- __init_begin = .;
- .init.text : {
- _sinittext = .;
- *(.init.text)
- _einittext = .;
- }
- .init.data : { *(.init.data) }
- . = ALIGN(16);
- __setup_start = .;
- .init.setup : { *(.init.setup) }
- __setup_end = .;
- __start___param = .;
- __param : { *(__param) }
- __stop___param = .;
- __initcall_start = .;
- .initcall.init : {
- *(.initcall1.init)
- *(.initcall2.init)
- *(.initcall3.init)
- *(.initcall4.init)
- *(.initcall5.init)
- *(.initcall6.init)
- *(.initcall7.init)
- }
- __initcall_end = .;
- __con_initcall_start = .;
- .con_initcall.init : { *(.con_initcall.init) }
- __con_initcall_end = .;
- SECURITY_INIT
- . = ALIGN(8192);
- __initramfs_start = .;
- .init.ramfs : { *(.init.ramfs) }
- __initramfs_end = .;
- . = ALIGN(8192);
- __init_end = .;
-
- .data.init_task : { *(.data.init_task) } /* The initial task and kernel stack */
-
- _end = . ;
-
- /* Sections to be discarded */
- /DISCARD/ : {
- *(.exit.text)
- *(.exit.data)
- *(.exitcall.exit)
- }
-
- /* Stabs debugging sections. */
- .stab 0 : { *(.stab) }
- .stabstr 0 : { *(.stabstr) }
- .stab.excl 0 : { *(.stab.excl) }
- .stab.exclstr 0 : { *(.stab.exclstr) }
- .stab.index 0 : { *(.stab.index) }
- .stab.indexstr 0 : { *(.stab.indexstr) }
- .comment 0 : { *(.comment) }
-}
--- linux-2.6.0-test4/arch/m68k/vmlinux-sun3.lds Sun Jun 15 09:37:32 2003
+++ linux-m68k-2.6.0-test4/arch/m68k/vmlinux-sun3.lds Tue Jun 24 14:30:53 2003
@@ -1,97 +0,0 @@
-/* ld script to make m68k Linux kernel */
-
-#include <asm-generic/vmlinux.lds.h>
-
-OUTPUT_FORMAT("elf32-m68k", "elf32-m68k", "elf32-m68k")
-OUTPUT_ARCH(m68k)
-ENTRY(_start)
-jiffies = jiffies_64 + 4;
-SECTIONS
-{
- . = 0xE004000;
- _text = .; /* Text and read-only data */
- .text : {
- *(.head)
- *(.text)
- *(.fixup)
- *(.gnu.warning)
- } = 0x4e75
- RODATA
-
- _etext = .; /* End of text section */
-
- .data : { /* Data */
- *(.data)
- CONSTRUCTORS
- . = ALIGN(16); /* Exception table */
- __start___ex_table = .;
- *(__ex_table)
- __stop___ex_table = .;
- }
- /* End of data goes *here* so that freeing init code works properly. */
- _edata = .;
-
- /* will be freed after init */
- . = ALIGN(8192); /* Init code and data */
-__init_begin = .;
- .init.text : {
- _sinittext = .;
- *(.init.text)
- _einittext = .;
- }
- .init.data : { *(.init.data) }
- . = ALIGN(16);
- __setup_start = .;
- .init.setup : { *(.init.setup) }
- __setup_end = .;
- __start___param = .;
- __param : { *(__param) }
- __stop___param = .;
- __initcall_start = .;
- .initcall.init : {
- *(.initcall1.init)
- *(.initcall2.init)
- *(.initcall3.init)
- *(.initcall4.init)
- *(.initcall5.init)
- *(.initcall6.init)
- *(.initcall7.init)
- }
- __initcall_end = .;
- __con_initcall_start = .;
- .con_initcall.init : { *(.con_initcall.init) }
- __con_initcall_end = .;
- SECURITY_INIT
- . = ALIGN(8192);
- __initramfs_start = .;
- .init.ramfs : { *(.init.ramfs) }
- __initramfs_end = .;
- . = ALIGN(8192);
- __init_end = .;
- .init.task : { *(init_task) }
-
-
- .bss : { *(.bss) } /* BSS */
-
- _end = . ;
-
- /* Sections to be discarded */
- /DISCARD/ : {
- *(.exit.text)
- *(.exit.data)
- *(.exitcall.exit)
- }
-
- .crap : {
- /* Stabs debugging sections. */
- *(.stab)
- *(.stabstr)
- *(.stab.excl)
- *(.stab.exclstr)
- *(.stab.index)
- *(.stab.indexstr)
- *(.comment)
- *(.note)
- }
-
-}
--- linux-2.6.0-test4/arch/m68k/kernel/vmlinux-std.lds Tue Jun 24 14:30:53 2003
+++ linux-m68k-2.6.0-test4/arch/m68k/kernel/vmlinux-std.lds Sun Jun 15 10:46:43 2003
@@ -0,0 +1,97 @@
+/* ld script to make m68k Linux kernel */
+
+#include <asm-generic/vmlinux.lds.h>
+
+OUTPUT_FORMAT("elf32-m68k", "elf32-m68k", "elf32-m68k")
+OUTPUT_ARCH(m68k)
+ENTRY(_start)
+jiffies = jiffies_64 + 4;
+SECTIONS
+{
+ . = 0x1000;
+ _text = .; /* Text and read-only data */
+ .text : {
+ *(.text)
+ *(.fixup)
+ *(.gnu.warning)
+ } = 0x4e75
+
+ . = ALIGN(16); /* Exception table */
+ __start___ex_table = .;
+ __ex_table : { *(__ex_table) }
+ __stop___ex_table = .;
+
+ RODATA
+
+ _etext = .; /* End of text section */
+
+ .data : { /* Data */
+ *(.data)
+ CONSTRUCTORS
+ }
+
+ .bss : { *(.bss) } /* BSS */
+
+ . = ALIGN(16);
+ .data.cacheline_aligned : { *(.data.cacheline_aligned) }
+
+ _edata = .; /* End of data section */
+
+ /* will be freed after init */
+ . = ALIGN(4096); /* Init code and data */
+ __init_begin = .;
+ .init.text : {
+ _sinittext = .;
+ *(.init.text)
+ _einittext = .;
+ }
+ .init.data : { *(.init.data) }
+ . = ALIGN(16);
+ __setup_start = .;
+ .init.setup : { *(.init.setup) }
+ __setup_end = .;
+ __start___param = .;
+ __param : { *(__param) }
+ __stop___param = .;
+ __initcall_start = .;
+ .initcall.init : {
+ *(.initcall1.init)
+ *(.initcall2.init)
+ *(.initcall3.init)
+ *(.initcall4.init)
+ *(.initcall5.init)
+ *(.initcall6.init)
+ *(.initcall7.init)
+ }
+ __initcall_end = .;
+ __con_initcall_start = .;
+ .con_initcall.init : { *(.con_initcall.init) }
+ __con_initcall_end = .;
+ SECURITY_INIT
+ . = ALIGN(8192);
+ __initramfs_start = .;
+ .init.ramfs : { *(.init.ramfs) }
+ __initramfs_end = .;
+ . = ALIGN(8192);
+ __init_end = .;
+
+ .data.init_task : { *(.data.init_task) } /* The initial task and kernel stack */
+
+ _end = . ;
+
+ /* Sections to be discarded */
+ /DISCARD/ : {
+ *(.exit.text)
+ *(.exit.data)
+ *(.exitcall.exit)
+ }
+
+ /* Stabs debugging sections. */
+ .stab 0 : { *(.stab) }
+ .stabstr 0 : { *(.stabstr) }
+ .stab.excl 0 : { *(.stab.excl) }
+ .stab.exclstr 0 : { *(.stab.exclstr) }
+ .stab.index 0 : { *(.stab.index) }
+ .stab.indexstr 0 : { *(.stab.indexstr) }
+ .comment 0 : { *(.comment) }
+}
--- linux-2.6.0-test4/arch/m68k/kernel/vmlinux-sun3.lds Tue Jun 24 14:30:53 2003
+++ linux-m68k-2.6.0-test4/arch/m68k/kernel/vmlinux-sun3.lds Sun Jun 15 10:46:43 2003
@@ -0,0 +1,97 @@
+/* ld script to make m68k Linux kernel */
+
+#include <asm-generic/vmlinux.lds.h>
+
+OUTPUT_FORMAT("elf32-m68k", "elf32-m68k", "elf32-m68k")
+OUTPUT_ARCH(m68k)
+ENTRY(_start)
+jiffies = jiffies_64 + 4;
+SECTIONS
+{
+ . = 0xE004000;
+ _text = .; /* Text and read-only data */
+ .text : {
+ *(.head)
+ *(.text)
+ *(.fixup)
+ *(.gnu.warning)
+ } = 0x4e75
+ RODATA
+
+ _etext = .; /* End of text section */
+
+ .data : { /* Data */
+ *(.data)
+ CONSTRUCTORS
+ . = ALIGN(16); /* Exception table */
+ __start___ex_table = .;
+ *(__ex_table)
+ __stop___ex_table = .;
+ }
+ /* End of data goes *here* so that freeing init code works properly. */
+ _edata = .;
+
+ /* will be freed after init */
+ . = ALIGN(8192); /* Init code and data */
+__init_begin = .;
+ .init.text : {
+ _sinittext = .;
+ *(.init.text)
+ _einittext = .;
+ }
+ .init.data : { *(.init.data) }
+ . = ALIGN(16);
+ __setup_start = .;
+ .init.setup : { *(.init.setup) }
+ __setup_end = .;
+ __start___param = .;
+ __param : { *(__param) }
+ __stop___param = .;
+ __initcall_start = .;
+ .initcall.init : {
+ *(.initcall1.init)
+ *(.initcall2.init)
+ *(.initcall3.init)
+ *(.initcall4.init)
+ *(.initcall5.init)
+ *(.initcall6.init)
+ *(.initcall7.init)
+ }
+ __initcall_end = .;
+ __con_initcall_start = .;
+ .con_initcall.init : { *(.con_initcall.init) }
+ __con_initcall_end = .;
+ SECURITY_INIT
+ . = ALIGN(8192);
+ __initramfs_start = .;
+ .init.ramfs : { *(.init.ramfs) }
+ __initramfs_end = .;
+ . = ALIGN(8192);
+ __init_end = .;
+ .init.task : { *(init_task) }
+
+
+ .bss : { *(.bss) } /* BSS */
+
+ _end = . ;
+
+ /* Sections to be discarded */
+ /DISCARD/ : {
+ *(.exit.text)
+ *(.exit.data)
+ *(.exitcall.exit)
+ }
+
+ .crap : {
+ /* Stabs debugging sections. */
+ *(.stab)
+ *(.stabstr)
+ *(.stab.excl)
+ *(.stab.exclstr)
+ *(.stab.index)
+ *(.stab.indexstr)
+ *(.comment)
+ *(.note)
+ }
+
+}
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH] macide (was: Re: Linux 2.6.0-test4)
2003-08-23 0:48 Linux 2.6.0-test4 Linus Torvalds
` (3 preceding siblings ...)
2003-08-24 11:47 ` [PATCH] vmlinux-*.lds " Geert Uytterhoeven
@ 2003-08-24 11:51 ` Geert Uytterhoeven
2003-08-24 12:20 ` Christoph Hellwig
2003-08-25 21:00 ` [patch] 2.6.0-test4: sis190 doesn't compile with gcc 2.95 Adrian Bunk
` (3 subsequent siblings)
8 siblings, 1 reply; 20+ messages in thread
From: Geert Uytterhoeven @ 2003-08-24 11:51 UTC (permalink / raw)
To: Bartlomiej Zolnierkiewicz
Cc: Linus Torvalds, Andrew Morton, Kernel Mailing List
On Fri, 22 Aug 2003, Linus Torvalds wrote:
> Bartlomiej Zolnierkiewicz:
> o ide: disk geometry/capacity cleanups
> o ide: always store disk capacity in u64
You forgot to update the Macintosh IDE driver:
--- linux-2.6.0-test4/drivers/ide/legacy/macide.c Tue Feb 25 10:21:12 2003
+++ linux-m68k-2.6.0-test4/drivers/ide/legacy/macide.c Sun Aug 24 12:37:06 2003
@@ -126,7 +126,7 @@
/* probing the drive which freezes a 190. */
ide_drive_t *drive = &ide_hwifs[index].drives[0];
- drive->capacity = drive->cyl*drive->head*drive->sect;
+ drive->capacity64 = drive->cyl*drive->head*drive->sect;
#ifdef CONFIG_BLK_DEV_MAC_MEDIABAY
request_irq(IRQ_BABOON_2, macide_mediabay_interrupt,
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH] macide (was: Re: Linux 2.6.0-test4)
2003-08-24 11:51 ` [PATCH] macide " Geert Uytterhoeven
@ 2003-08-24 12:20 ` Christoph Hellwig
2003-08-24 12:29 ` Geert Uytterhoeven
0 siblings, 1 reply; 20+ messages in thread
From: Christoph Hellwig @ 2003-08-24 12:20 UTC (permalink / raw)
To: Geert Uytterhoeven; +Cc: Kernel Mailing List
On Sun, Aug 24, 2003 at 01:51:20PM +0200, Geert Uytterhoeven wrote:
> On Fri, 22 Aug 2003, Linus Torvalds wrote:
> > Bartlomiej Zolnierkiewicz:
> > o ide: disk geometry/capacity cleanups
> > o ide: always store disk capacity in u64
>
> You forgot to update the Macintosh IDE driver:
Btw, what's the state of mac68k (and the other m68k subarches) on
2.6?
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH] macide (was: Re: Linux 2.6.0-test4)
2003-08-24 12:20 ` Christoph Hellwig
@ 2003-08-24 12:29 ` Geert Uytterhoeven
0 siblings, 0 replies; 20+ messages in thread
From: Geert Uytterhoeven @ 2003-08-24 12:29 UTC (permalink / raw)
To: Christoph Hellwig; +Cc: Linux/m68k, Kernel Mailing List
On Sun, 24 Aug 2003, Christoph Hellwig wrote:
> On Sun, Aug 24, 2003 at 01:51:20PM +0200, Geert Uytterhoeven wrote:
> > On Fri, 22 Aug 2003, Linus Torvalds wrote:
> > > Bartlomiej Zolnierkiewicz:
> > > o ide: disk geometry/capacity cleanups
> > > o ide: always store disk capacity in u64
> >
> > You forgot to update the Macintosh IDE driver:
>
> Btw, what's the state of mac68k (and the other m68k subarches) on
> 2.6?
Amiga, Sun-3/3x and probably Q40/Q60 are working, except for some SCSI drivers.
Other subarches are in a worse shape.
In general, 2.6.0-test4 on m68k isn't that far from 2.4.22-rc3, except for some
SCSI breakage.
You can check out the status at http://linux-m68k-cvs.apia.dhs.org/~geert/.
The patch pages are usually up-to-date, the feature status pages aren't (e.g.
basic m68k support got fixed a few weeks ago).
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 20+ messages in thread
* [patch] 2.6.0-test4: sis190 doesn't compile with gcc 2.95
2003-08-23 0:48 Linux 2.6.0-test4 Linus Torvalds
` (4 preceding siblings ...)
2003-08-24 11:51 ` [PATCH] macide " Geert Uytterhoeven
@ 2003-08-25 21:00 ` Adrian Bunk
2003-08-26 17:44 ` Jeff Garzik
2003-08-25 21:20 ` Linux 2.6.0-test4 insecure
` (2 subsequent siblings)
8 siblings, 1 reply; 20+ messages in thread
From: Adrian Bunk @ 2003-08-25 21:00 UTC (permalink / raw)
To: kmliu, Jeff Garzik; +Cc: Kernel Mailing List
On Fri, Aug 22, 2003 at 05:48:56PM -0700, Linus Torvalds wrote:
>...
> Summary of changes from v2.6.0-test3 to v2.6.0-test4
> ============================================
>...
> Jeff Garzik:
>...
> o [netdrvr] add sis190 gigabit ethernet driver (note: needs work)
>...
The following is needed to fix the compilation of sis190 with gcc 2.95:
--- linux-2.6.0-test4-mm1/drivers/net/sis190.c.old 2003-08-25 20:03:04.000000000 +0200
+++ linux-2.6.0-test4-mm1/drivers/net/sis190.c 2003-08-25 20:03:45.000000000 +0200
@@ -536,6 +536,7 @@
static int printed_version = 0;
int i, rc;
u16 reg31;
+ int val;
assert(pdev != NULL);
assert(ent != NULL);
@@ -620,7 +621,7 @@
dev->dev_addr[2], dev->dev_addr[3],
dev->dev_addr[4], dev->dev_addr[5], dev->irq);
- int val = smdio_read(ioaddr, PHY_AUTO_NEGO_REG);
+ val = smdio_read(ioaddr, PHY_AUTO_NEGO_REG);
printk(KERN_INFO "%s: Auto-negotiation Enabled.\n", dev->name);
cu
Adrian
--
"Is there not promise of rain?" Ling Tan asked suddenly out
of the darkness. There had been need of rain for many days.
"Only a promise," Lao Er said.
Pearl S. Buck - Dragon Seed
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Linux 2.6.0-test4
2003-08-23 0:48 Linux 2.6.0-test4 Linus Torvalds
` (5 preceding siblings ...)
2003-08-25 21:00 ` [patch] 2.6.0-test4: sis190 doesn't compile with gcc 2.95 Adrian Bunk
@ 2003-08-25 21:20 ` insecure
2003-08-25 21:26 ` [PATCH] raceless request_region() fix (was Re: Linux 2.6.0-test4) insecure
2003-08-25 22:56 ` Linux 2.6.0-test4 (compile statistics) John Cherry
2003-08-30 9:04 ` Linux 2.6.0-test4 Ralf Hildebrandt
8 siblings, 1 reply; 20+ messages in thread
From: insecure @ 2003-08-25 21:20 UTC (permalink / raw)
To: Linus Torvalds, Kernel Mailing List
> o [arcnet com90io] replace check_region with temporary
> request_region, in probe phase.
check_region() is deprecated because it is racy.
Replacing it with request_region in probe:
int probe() {
if(!request_region(...))
return 0;
/* probe */
release_region(...);
}
int init() {
request_region(...);
}
only removes 'deprecated' warning. Race remains.
--
vda
^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH] raceless request_region() fix (was Re: Linux 2.6.0-test4)
2003-08-25 21:20 ` Linux 2.6.0-test4 insecure
@ 2003-08-25 21:26 ` insecure
2003-08-25 21:59 ` Jeff Garzik
0 siblings, 1 reply; 20+ messages in thread
From: insecure @ 2003-08-25 21:26 UTC (permalink / raw)
To: Jeff Garzik, Linus Torvalds, Kernel Mailing List
On Tuesday 26 August 2003 00:20, insecure wrote:
> > o [arcnet com90io] replace check_region with temporary
> > request_region, in probe phase.
>
> check_region() is deprecated because it is racy.
> Replacing it with request_region in probe:
>
> int probe() {
> if(!request_region(...))
> return 0;
> /* probe */
> release_region(...);
> }
>
> int init() {
> request_region(...);
> }
>
> only removes 'deprecated' warning. Race remains.
Corrected com90io.c patch is below.
--
vda
--- linux-2.6.0-test4/drivers/net/arcnet/com90io.c.orig Sat Aug 23 02:53:52 2003
+++ linux-2.6.0-test4/drivers/net/arcnet/com90io.c Tue Aug 26 00:22:51 2003
@@ -158,7 +158,7 @@
"must specify the base address!\n");
return -ENODEV;
}
- if (!request_region(ioaddr, ARCNET_TOTAL_SIZE, "com90io probe")) {
+ if (!request_region(ioaddr, ARCNET_TOTAL_SIZE, "arcnet (COM90xx-IO)")) {
BUGMSG(D_INIT_REASONS, "IO check_region %x-%x failed.\n",
ioaddr, ioaddr + ARCNET_TOTAL_SIZE - 1);
return -ENXIO;
@@ -218,7 +218,6 @@
goto err_out;
}
}
- release_region(ioaddr, ARCNET_TOTAL_SIZE); /* end of probing */
return com90io_found(dev);
err_out:
@@ -237,13 +236,9 @@
/* Reserve the irq */
if (request_irq(dev->irq, &arcnet_interrupt, 0, "arcnet (COM90xx-IO)", dev)) {
+ release_region(dev->base_addr, ARCNET_TOTAL_SIZE);
BUGMSG(D_NORMAL, "Can't get IRQ %d!\n", dev->irq);
return -ENODEV;
- }
- /* Reserve the I/O region - guaranteed to work by check_region */
- if (!request_region(dev->base_addr, ARCNET_TOTAL_SIZE, "arcnet (COM90xx-IO)")) {
- free_irq(dev->irq, dev);
- return -EBUSY;
}
/* Initialize the rest of the device structure. */
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH] raceless request_region() fix (was Re: Linux 2.6.0-test4)
2003-08-25 21:26 ` [PATCH] raceless request_region() fix (was Re: Linux 2.6.0-test4) insecure
@ 2003-08-25 21:59 ` Jeff Garzik
2003-08-26 5:20 ` insecure
0 siblings, 1 reply; 20+ messages in thread
From: Jeff Garzik @ 2003-08-25 21:59 UTC (permalink / raw)
To: insecure; +Cc: Linus Torvalds, Kernel Mailing List
Is it a race if noone cares? :)
The code does
if (!request_region(...))
fail
touch hardware
release_region
if (!request_region(...))
fail
If the HIGHLY UNLIKELY event of another ISA driver claiming this region
occurs, the system continues working just fine.
At the time, I was thinking that any further touching of the code should
be converting it to a more pnp-like structure.
Jeff
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH] raceless request_region() fix (was Re: Linux 2.6.0-test4)
2003-08-25 21:59 ` Jeff Garzik
@ 2003-08-26 5:20 ` insecure
0 siblings, 0 replies; 20+ messages in thread
From: insecure @ 2003-08-26 5:20 UTC (permalink / raw)
To: Jeff Garzik; +Cc: Kernel Mailing List
[de-cc'ing Linus]
On Tuesday 26 August 2003 00:59, Jeff Garzik wrote:
> Is it a race if noone cares? :)
>
> The code does
>
> if (!request_region(...))
> fail
> touch hardware
> release_region
> if (!request_region(...))
> fail
>
> If the HIGHLY UNLIKELY event of another ISA driver claiming this region
> occurs, the system continues working just fine.
Yes, this particular driver is fine. My patch just eliminate back-to-back
release_region(...)
if (!request_region(...)) fail;
pair.
I just have a feeling that if I am going to replace check_region with
request_region, I can close race window altogether.
BTW, it all started when I tried to get rid of check_region in de4x5.c.
That's a bit worse. For example:
barrier();
request_region(iobase, (lp->bus == PCI ? DE4X5_PCI_TOTAL_SIZE :
DE4X5_EISA_TOTAL_SIZE),
lp->adapter_name);
lp->rxRingSize = NUM_RX_DESC;
--
vda
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Linux 2.6.0-test4 (compile statistics)
2003-08-23 0:48 Linux 2.6.0-test4 Linus Torvalds
` (6 preceding siblings ...)
2003-08-25 21:20 ` Linux 2.6.0-test4 insecure
@ 2003-08-25 22:56 ` John Cherry
2003-08-30 9:04 ` Linux 2.6.0-test4 Ralf Hildebrandt
8 siblings, 0 replies; 20+ messages in thread
From: John Cherry @ 2003-08-25 22:56 UTC (permalink / raw)
To: Linus Torvalds; +Cc: Kernel Mailing List
Compile statistics: 2.6.0-test4
Compiler: gcc 3.2.2
Script: http://developer.osdl.org/~cherry/compile/compregress.sh
bzImage bzImage modules
(defconfig) (allmodconfig) (allmodconfig)
2.6.0-test4 0 warnings 3 warnings 1016 warnings
0 errors 0 errors 34 errors
2.6.0-test3 0 warnings 7 warnings 984 warnings
0 errors 9 errors 42 errors
2.6.0-test2 0 warnings 7 warnings 1201 warnings
0 errors 9 errors 43 errors
2.6.0-test1 0 warnings 8 warnings 1319 warnings
0 errors 9 errors 38 errors
Compile statistics for 2.5 kernels and 2.6 kernels are at:
http://developer.osdl.org/~cherry/compile/
Failure summary:
drivers/block: 2 warnings, 1 errors
drivers/isdn: 257 warnings, 6 errors
drivers/media: 5 warnings, 5 errors
drivers/mtd: 25 warnings, 1 errors
drivers/net: 208 warnings, 8 errors
drivers/net: 36 warnings, 8 errors
drivers/scsi/aic7xxx: 0 warnings, 3 errors
drivers/scsi: 97 warnings, 7 errors
drivers/video: 8 warnings, 3 errors
sound/oss: 49 warnings, 1 errors
sound/pcmcia: 0 warnings, 2 errors
sound: 0 warnings, 3 errors
Warning summary:
drivers/atm: 12 warnings, 0 errors
drivers/cdrom: 26 warnings, 0 errors
drivers/char: 244 warnings, 0 errors
drivers/i2c: 3 warnings, 0 errors
drivers/ide: 30 warnings, 0 errors
drivers/md: 2 warnings, 0 errors
drivers/message: 1 warnings, 0 errors
drivers/pcmcia: 3 warnings, 0 errors
drivers/scsi/pcmcia: 4 warnings, 0 errors
drivers/scsi/sym53c8xx_2: 2 warnings, 0 errors
drivers/serial: 1 warnings, 0 errors
drivers/telephony: 5 warnings, 0 errors
drivers/usb: 5 warnings, 0 errors
drivers/video/aty: 3 warnings, 0 errors
drivers/video/console: 2 warnings, 0 errors
drivers/video/matrox: 5 warnings, 0 errors
drivers/video/sis: 1 warnings, 0 errors
fs/afs: 2 warnings, 0 errors
fs/intermezzo: 1 warnings, 0 errors
fs/smbfs: 2 warnings, 0 errors
net: 13 warnings, 0 errors
sound/isa: 3 warnings, 0 errors
John
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: Linux 2.6.0-test4
2003-08-23 0:48 Linux 2.6.0-test4 Linus Torvalds
` (7 preceding siblings ...)
2003-08-25 22:56 ` Linux 2.6.0-test4 (compile statistics) John Cherry
@ 2003-08-30 9:04 ` Ralf Hildebrandt
8 siblings, 0 replies; 20+ messages in thread
From: Ralf Hildebrandt @ 2003-08-30 9:04 UTC (permalink / raw)
To: Kernel Mailing List
* Linus Torvalds <torvalds@osdl.org>:
>
> There should be a lot of compile fixes here, along with updates for ia64,
> and the (painful) move of the 'name' entry out of the "struct device" that
> helps avoid unnecessary memory waste.
>
> It's a lot of small stuff all over: nothing really stands out in diffstat,
> except the big update of the Zoran video capture driver, and the blkmtd
> driver - both updated from their respective development trees (and the ips
> scsi driver, but that was due to massive whitespace fixing).
>
> Normal merges with Andrew and arch maintainers (x86-64, ia64, sparc64,
> arm), and AGP updates (notably the merging of the ATI IGP). And network
> driver updates, ACPI and power management infrastructure.
This one is actually usable on my laptop (Sattelite Pro 6100 by
Toshiba). ACPI works, ALSA work, and it seems to work in general.
I still have issues with the keyboard -- sometimes when typing in the
frambuffer console I get an "unknown scancode" and after that the CTRL
key is stuck forever, which forces me to reboot.
--
Ralf Hildebrandt (Im Auftrag des Referat V a) Ralf.Hildebrandt@charite.de
Charite Campus Mitte Tel. +49 (0)30-450 570-155
Referat V a - Kommunikationsnetze - Fax. +49 (0)30-450 570-916
AIM: ralfpostfix
^ permalink raw reply [flat|nested] 20+ messages in thread