From: Cyrille Pitchen <cyrille.pitchen@atmel.com>
To: <computersforpeace@gmail.com>, <marek.vasut@gmail.com>,
<boris.brezillon@free-electrons.com>, <richard@nod.at>,
<linux-mtd@lists.infradead.org>
Cc: <nicolas.ferre@atmel.com>, <linux-kernel@vger.kernel.org>,
Cyrille Pitchen <cyrille.pitchen@atmel.com>
Subject: [PATCH v4 2/8] mtd: spi-nor: rename SPINOR_OP_* macros of the 4-byte address op codes
Date: Mon, 21 Nov 2016 15:15:41 +0100 [thread overview]
Message-ID: <47b7bf0ec441753e55786d39f8152218d3052ae3.1479736401.git.cyrille.pitchen@atmel.com> (raw)
In-Reply-To: <cover.1479736401.git.cyrille.pitchen@atmel.com>
This patch renames the SPINOR_OP_* macros of the 4-byte address
instruction set so the new names all share a common pattern: the 4-byte
address name is built from the 3-byte address name appending the "_4B"
suffix.
The patch also introduces new op codes to support other SPI protocols such
as SPI 1-4-4 and SPI 1-2-2.
This is a transitional patch and will help a later patch of spi-nor.c
to automate the translation from the 3-byte address op codes into their
4-byte address version.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
---
drivers/mtd/devices/serial_flash_cmds.h | 7 -------
drivers/mtd/devices/st_spi_fsm.c | 28 ++++++++++++++--------------
drivers/mtd/spi-nor/spi-nor.c | 8 ++++----
drivers/spi/spi-bcm-qspi.c | 6 +++---
include/linux/mtd/spi-nor.h | 22 ++++++++++++++++------
5 files changed, 37 insertions(+), 34 deletions(-)
diff --git a/drivers/mtd/devices/serial_flash_cmds.h b/drivers/mtd/devices/serial_flash_cmds.h
index f59a125295d0..8b81e15105dd 100644
--- a/drivers/mtd/devices/serial_flash_cmds.h
+++ b/drivers/mtd/devices/serial_flash_cmds.h
@@ -18,19 +18,12 @@
#define SPINOR_OP_RDVCR 0x85
/* JEDEC Standard - Serial Flash Discoverable Parmeters (SFDP) Commands */
-#define SPINOR_OP_READ_1_2_2 0xbb /* DUAL I/O READ */
-#define SPINOR_OP_READ_1_4_4 0xeb /* QUAD I/O READ */
-
#define SPINOR_OP_WRITE 0x02 /* PAGE PROGRAM */
#define SPINOR_OP_WRITE_1_1_2 0xa2 /* DUAL INPUT PROGRAM */
#define SPINOR_OP_WRITE_1_2_2 0xd2 /* DUAL INPUT EXT PROGRAM */
#define SPINOR_OP_WRITE_1_1_4 0x32 /* QUAD INPUT PROGRAM */
#define SPINOR_OP_WRITE_1_4_4 0x12 /* QUAD INPUT EXT PROGRAM */
-/* READ commands with 32-bit addressing */
-#define SPINOR_OP_READ4_1_2_2 0xbc
-#define SPINOR_OP_READ4_1_4_4 0xec
-
/* Configuration flags */
#define FLASH_FLAG_SINGLE 0x000000ff
#define FLASH_FLAG_READ_WRITE 0x00000001
diff --git a/drivers/mtd/devices/st_spi_fsm.c b/drivers/mtd/devices/st_spi_fsm.c
index 5454b4113589..804313a33f2b 100644
--- a/drivers/mtd/devices/st_spi_fsm.c
+++ b/drivers/mtd/devices/st_spi_fsm.c
@@ -507,13 +507,13 @@ static struct seq_rw_config n25q_read3_configs[] = {
* - 'FAST' variants configured for 8 dummy cycles (see note above.)
*/
static struct seq_rw_config n25q_read4_configs[] = {
- {FLASH_FLAG_READ_1_4_4, SPINOR_OP_READ4_1_4_4, 0, 4, 4, 0x00, 0, 8},
- {FLASH_FLAG_READ_1_1_4, SPINOR_OP_READ4_1_1_4, 0, 1, 4, 0x00, 0, 8},
- {FLASH_FLAG_READ_1_2_2, SPINOR_OP_READ4_1_2_2, 0, 2, 2, 0x00, 0, 8},
- {FLASH_FLAG_READ_1_1_2, SPINOR_OP_READ4_1_1_2, 0, 1, 2, 0x00, 0, 8},
- {FLASH_FLAG_READ_FAST, SPINOR_OP_READ4_FAST, 0, 1, 1, 0x00, 0, 8},
- {FLASH_FLAG_READ_WRITE, SPINOR_OP_READ4, 0, 1, 1, 0x00, 0, 0},
- {0x00, 0, 0, 0, 0, 0x00, 0, 0},
+ {FLASH_FLAG_READ_1_4_4, SPINOR_OP_READ_1_4_4_4B, 0, 4, 4, 0x00, 0, 8},
+ {FLASH_FLAG_READ_1_1_4, SPINOR_OP_READ_1_1_4_4B, 0, 1, 4, 0x00, 0, 8},
+ {FLASH_FLAG_READ_1_2_2, SPINOR_OP_READ_1_2_2_4B, 0, 2, 2, 0x00, 0, 8},
+ {FLASH_FLAG_READ_1_1_2, SPINOR_OP_READ_1_1_2_4B, 0, 1, 2, 0x00, 0, 8},
+ {FLASH_FLAG_READ_FAST, SPINOR_OP_READ_FAST_4B, 0, 1, 1, 0x00, 0, 8},
+ {FLASH_FLAG_READ_WRITE, SPINOR_OP_READ_4B, 0, 1, 1, 0x00, 0, 0},
+ {0x00, 0, 0, 0, 0, 0x00, 0, 0},
};
/*
@@ -553,13 +553,13 @@ static int stfsm_mx25_en_32bit_addr_seq(struct stfsm_seq *seq)
* entering a state that is incompatible with the SPIBoot Controller.
*/
static struct seq_rw_config stfsm_s25fl_read4_configs[] = {
- {FLASH_FLAG_READ_1_4_4, SPINOR_OP_READ4_1_4_4, 0, 4, 4, 0x00, 2, 4},
- {FLASH_FLAG_READ_1_1_4, SPINOR_OP_READ4_1_1_4, 0, 1, 4, 0x00, 0, 8},
- {FLASH_FLAG_READ_1_2_2, SPINOR_OP_READ4_1_2_2, 0, 2, 2, 0x00, 4, 0},
- {FLASH_FLAG_READ_1_1_2, SPINOR_OP_READ4_1_1_2, 0, 1, 2, 0x00, 0, 8},
- {FLASH_FLAG_READ_FAST, SPINOR_OP_READ4_FAST, 0, 1, 1, 0x00, 0, 8},
- {FLASH_FLAG_READ_WRITE, SPINOR_OP_READ4, 0, 1, 1, 0x00, 0, 0},
- {0x00, 0, 0, 0, 0, 0x00, 0, 0},
+ {FLASH_FLAG_READ_1_4_4, SPINOR_OP_READ_1_4_4_4B, 0, 4, 4, 0x00, 2, 4},
+ {FLASH_FLAG_READ_1_1_4, SPINOR_OP_READ_1_1_4_4B, 0, 1, 4, 0x00, 0, 8},
+ {FLASH_FLAG_READ_1_2_2, SPINOR_OP_READ_1_2_2_4B, 0, 2, 2, 0x00, 4, 0},
+ {FLASH_FLAG_READ_1_1_2, SPINOR_OP_READ_1_1_2_4B, 0, 1, 2, 0x00, 0, 8},
+ {FLASH_FLAG_READ_FAST, SPINOR_OP_READ_FAST_4B, 0, 1, 1, 0x00, 0, 8},
+ {FLASH_FLAG_READ_WRITE, SPINOR_OP_READ_4B, 0, 1, 1, 0x00, 0, 0},
+ {0x00, 0, 0, 0, 0, 0x00, 0, 0},
};
static struct seq_rw_config stfsm_s25fl_write4_configs[] = {
diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
index 7ff807211e1e..8a190122b13f 100644
--- a/drivers/mtd/spi-nor/spi-nor.c
+++ b/drivers/mtd/spi-nor/spi-nor.c
@@ -1480,16 +1480,16 @@ int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode)
/* Dedicated 4-byte command set */
switch (nor->flash_read) {
case SPI_NOR_QUAD:
- nor->read_opcode = SPINOR_OP_READ4_1_1_4;
+ nor->read_opcode = SPINOR_OP_READ_1_1_4_4B;
break;
case SPI_NOR_DUAL:
- nor->read_opcode = SPINOR_OP_READ4_1_1_2;
+ nor->read_opcode = SPINOR_OP_READ_1_1_2_4B;
break;
case SPI_NOR_FAST:
- nor->read_opcode = SPINOR_OP_READ4_FAST;
+ nor->read_opcode = SPINOR_OP_READ_FAST_4B;
break;
case SPI_NOR_NORMAL:
- nor->read_opcode = SPINOR_OP_READ4;
+ nor->read_opcode = SPINOR_OP_READ_4B;
break;
}
nor->program_opcode = SPINOR_OP_PP_4B;
diff --git a/drivers/spi/spi-bcm-qspi.c b/drivers/spi/spi-bcm-qspi.c
index 14f9dea3173f..d7843fd8c610 100644
--- a/drivers/spi/spi-bcm-qspi.c
+++ b/drivers/spi/spi-bcm-qspi.c
@@ -371,7 +371,7 @@ static int bcm_qspi_bspi_set_flex_mode(struct bcm_qspi *qspi, int width,
/* default mode, does not need flex_cmd */
flex_mode = 0;
else
- command = SPINOR_OP_READ4_FAST;
+ command = SPINOR_OP_READ_FAST_4B;
break;
case SPI_NBITS_DUAL:
bpc = 0x00000001;
@@ -384,7 +384,7 @@ static int bcm_qspi_bspi_set_flex_mode(struct bcm_qspi *qspi, int width,
} else {
command = SPINOR_OP_READ_1_1_2;
if (spans_4byte)
- command = SPINOR_OP_READ4_1_1_2;
+ command = SPINOR_OP_READ_1_1_2_4B;
}
break;
case SPI_NBITS_QUAD:
@@ -399,7 +399,7 @@ static int bcm_qspi_bspi_set_flex_mode(struct bcm_qspi *qspi, int width,
} else {
command = SPINOR_OP_READ_1_1_4;
if (spans_4byte)
- command = SPINOR_OP_READ4_1_1_4;
+ command = SPINOR_OP_READ_1_1_4_4B;
}
break;
default:
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
index c425c7b4c2a0..8b02fd7864d0 100644
--- a/include/linux/mtd/spi-nor.h
+++ b/include/linux/mtd/spi-nor.h
@@ -43,9 +43,13 @@
#define SPINOR_OP_WRSR 0x01 /* Write status register 1 byte */
#define SPINOR_OP_READ 0x03 /* Read data bytes (low frequency) */
#define SPINOR_OP_READ_FAST 0x0b /* Read data bytes (high frequency) */
-#define SPINOR_OP_READ_1_1_2 0x3b /* Read data bytes (Dual SPI) */
-#define SPINOR_OP_READ_1_1_4 0x6b /* Read data bytes (Quad SPI) */
+#define SPINOR_OP_READ_1_1_2 0x3b /* Read data bytes (Dual Output SPI) */
+#define SPINOR_OP_READ_1_2_2 0xbb /* Read data bytes (Dual I/O SPI) */
+#define SPINOR_OP_READ_1_1_4 0x6b /* Read data bytes (Quad Output SPI) */
+#define SPINOR_OP_READ_1_4_4 0xeb /* Read data bytes (Quad I/O SPI) */
#define SPINOR_OP_PP 0x02 /* Page program (up to 256 bytes) */
+#define SPINOR_OP_PP_1_1_4 0x32 /* Quad page program */
+#define SPINOR_OP_PP_1_4_4 0x38 /* Quad page program */
#define SPINOR_OP_BE_4K 0x20 /* Erase 4KiB block */
#define SPINOR_OP_BE_4K_PMC 0xd7 /* Erase 4KiB block on PMC chips */
#define SPINOR_OP_BE_32K 0x52 /* Erase 32KiB block */
@@ -56,11 +60,17 @@
#define SPINOR_OP_RDFSR 0x70 /* Read flag status register */
/* 4-byte address opcodes - used on Spansion and some Macronix flashes. */
-#define SPINOR_OP_READ4 0x13 /* Read data bytes (low frequency) */
-#define SPINOR_OP_READ4_FAST 0x0c /* Read data bytes (high frequency) */
-#define SPINOR_OP_READ4_1_1_2 0x3c /* Read data bytes (Dual SPI) */
-#define SPINOR_OP_READ4_1_1_4 0x6c /* Read data bytes (Quad SPI) */
+#define SPINOR_OP_READ_4B 0x13 /* Read data bytes (low frequency) */
+#define SPINOR_OP_READ_FAST_4B 0x0c /* Read data bytes (high frequency) */
+#define SPINOR_OP_READ_1_1_2_4B 0x3c /* Read data bytes (Dual Output SPI) */
+#define SPINOR_OP_READ_1_2_2_4B 0xbc /* Read data bytes (Dual I/O SPI) */
+#define SPINOR_OP_READ_1_1_4_4B 0x6c /* Read data bytes (Quad Output SPI) */
+#define SPINOR_OP_READ_1_4_4_4B 0xec /* Read data bytes (Quad I/O SPI) */
#define SPINOR_OP_PP_4B 0x12 /* Page program (up to 256 bytes) */
+#define SPINOR_OP_PP_1_1_4_4B 0x34 /* Quad page program */
+#define SPINOR_OP_PP_1_4_4_4B 0x3e /* Quad page program */
+#define SPINOR_OP_BE_4K_4B 0x21 /* Erase 4KiB block */
+#define SPINOR_OP_BE_32K_4B 0x5c /* Erase 32KiB block */
#define SPINOR_OP_SE_4B 0xdc /* Sector erase (usually 64KiB) */
/* Used for SST flashes only. */
--
2.7.4
next prev parent reply other threads:[~2016-11-21 14:16 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-11-21 14:15 [PATCH v4 0/8] mtd: spi-nor: parse SFDP tables to setup (Q)SPI memories Cyrille Pitchen
2016-11-21 14:15 ` [PATCH v4 1/8] mtd: spi-nor: improve macronix_quad_enable() Cyrille Pitchen
2016-11-21 14:15 ` Cyrille Pitchen [this message]
2016-11-21 14:15 ` [PATCH v4 3/8] mtd: spi-nor: add an alternative method to support memory >16MiB Cyrille Pitchen
2016-11-21 14:15 ` [PATCH v4 4/8] mtd: spi-nor: add support of SPI protocols like SPI 1-2-2 and SPI 1-4-4 Cyrille Pitchen
2016-12-13 9:46 ` Krzeminski, Marcin (Nokia - PL/Wroclaw)
2016-12-16 13:47 ` Krzeminski, Marcin (Nokia - PL/Wroclaw)
2016-12-19 17:00 ` Cyrille Pitchen
2016-12-20 19:41 ` Odp.: " Krzeminski, Marcin (Nokia - PL/Wroclaw)
2016-12-19 16:38 ` Cyrille Pitchen
2016-12-20 19:36 ` Odp.: " Krzeminski, Marcin (Nokia - PL/Wroclaw)
2016-11-21 14:15 ` [PATCH v4 5/8] mtd: spi-nor: remove unused set_quad_mode() function Cyrille Pitchen
2016-11-21 14:15 ` [PATCH v4 6/8] mtd: m25p80: add support of dual and quad spi protocols to all commands Cyrille Pitchen
2016-11-21 14:15 ` [PATCH v4 7/8] mtd: spi-nor: parse Serial Flash Discoverable Parameters (SFDP) tables Cyrille Pitchen
2016-11-21 14:15 ` [PATCH v4 8/8] mtd: spi-nor: parse SFDP 4-byte Address Instruction Table Cyrille Pitchen
2016-12-13 9:46 ` [PATCH v4 0/8] mtd: spi-nor: parse SFDP tables to setup (Q)SPI memories Krzeminski, Marcin (Nokia - PL/Wroclaw)
2016-12-20 16:42 ` Cyrille Pitchen
2016-12-20 19:51 ` Odp.: " Krzeminski, Marcin (Nokia - PL/Wroclaw)
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=47b7bf0ec441753e55786d39f8152218d3052ae3.1479736401.git.cyrille.pitchen@atmel.com \
--to=cyrille.pitchen@atmel.com \
--cc=boris.brezillon@free-electrons.com \
--cc=computersforpeace@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=marek.vasut@gmail.com \
--cc=nicolas.ferre@atmel.com \
--cc=richard@nod.at \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).