Re: [PATCH v2 4/4] power: supply: Add Spreadtrum SC27XX fuel gauge unit driver

[Baolin Wang <baolin.wang@linaro.org>]

On 26 September 2018 at 23:30, Sebastian Reichel <sre@kernel.org> wrote:
> Hi,
>
> On Wed, Sep 26, 2018 at 10:59:14AM +0800, Baolin Wang wrote:
>> This patch adds the Spreadtrum SC27XX serial PMICs fuel gauge support,
>> which is used to calculate the battery capacity.
>>
>> Original-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
>> Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
>> ---
>> Changes from v1:
>>  - Use battery standard properties to get internal resistance and ocv table.
>>  - Change devm_gpiod_get_optional() to devm_gpiod_get().
>>  - Add power_supply_changed() when detecting battery present change.
>>  - Return micro volts for sc27xx_fgu_get_vbat_ocv().
>> ---
>>  drivers/power/supply/Kconfig             |    7 +
>>  drivers/power/supply/Makefile            |    1 +
>>  drivers/power/supply/sc27xx_fuel_gauge.c |  691 ++++++++++++++++++++++++++++++
>>  3 files changed, 699 insertions(+)
>>  create mode 100644 drivers/power/supply/sc27xx_fuel_gauge.c
>>
>> diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig
>> index f27cf07..917f4b7 100644
>> --- a/drivers/power/supply/Kconfig
>> +++ b/drivers/power/supply/Kconfig
>> @@ -652,4 +652,11 @@ config CHARGER_SC2731
>>        Say Y here to enable support for battery charging with SC2731
>>        PMIC chips.
>>
>> +config FUEL_GAUGE_SC27XX
>> +     tristate "Spreadtrum SC27XX fuel gauge driver"
>> +     depends on MFD_SC27XX_PMIC || COMPILE_TEST
>> +     help
>> +      Say Y here to enable support for fuel gauge with SC27XX
>> +      PMIC chips.
>> +
>>  endif # POWER_SUPPLY
>> diff --git a/drivers/power/supply/Makefile b/drivers/power/supply/Makefile
>> index 767105b..b731c2a 100644
>> --- a/drivers/power/supply/Makefile
>> +++ b/drivers/power/supply/Makefile
>> @@ -86,3 +86,4 @@ obj-$(CONFIG_AXP288_FUEL_GAUGE) += axp288_fuel_gauge.o
>>  obj-$(CONFIG_AXP288_CHARGER) += axp288_charger.o
>>  obj-$(CONFIG_CHARGER_CROS_USBPD)     += cros_usbpd-charger.o
>>  obj-$(CONFIG_CHARGER_SC2731) += sc2731_charger.o
>> +obj-$(CONFIG_FUEL_GAUGE_SC27XX)      += sc27xx_fuel_gauge.o
>> diff --git a/drivers/power/supply/sc27xx_fuel_gauge.c b/drivers/power/supply/sc27xx_fuel_gauge.c
>> new file mode 100644
>> index 0000000..d3422cf
>> --- /dev/null
>> +++ b/drivers/power/supply/sc27xx_fuel_gauge.c
>> @@ -0,0 +1,691 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +// Copyright (C) 2018 Spreadtrum Communications Inc.
>> +
>> +#include <linux/gpio/consumer.h>
>> +#include <linux/iio/consumer.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/kernel.h>
>> +#include <linux/module.h>
>> +#include <linux/of.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/power_supply.h>
>> +#include <linux/regmap.h>
>> +
>> +/* PMIC global control registers definition */
>> +#define SC27XX_MODULE_EN0            0xc08
>> +#define SC27XX_CLK_EN0                       0xc18
>> +#define SC27XX_FGU_EN                        BIT(7)
>> +#define SC27XX_FGU_RTC_EN            BIT(6)
>> +
>> +/* FGU registers definition */
>> +#define SC27XX_FGU_START             0x0
>> +#define SC27XX_FGU_CONFIG            0x4
>> +#define SC27XX_FGU_ADC_CONFIG                0x8
>> +#define SC27XX_FGU_STATUS            0xc
>> +#define SC27XX_FGU_INT_EN            0x10
>> +#define SC27XX_FGU_INT_CLR           0x14
>> +#define SC27XX_FGU_INT_STS           0x1c
>> +#define SC27XX_FGU_VOLTAGE           0x20
>> +#define SC27XX_FGU_OCV                       0x24
>> +#define SC27XX_FGU_POCV                      0x28
>> +#define SC27XX_FGU_CURRENT           0x2c
>> +#define SC27XX_FGU_CLBCNT_SETH               0x50
>> +#define SC27XX_FGU_CLBCNT_SETL               0x54
>> +#define SC27XX_FGU_CLBCNT_VALH               0x68
>> +#define SC27XX_FGU_CLBCNT_VALL               0x6c
>> +#define SC27XX_FGU_CLBCNT_QMAXL              0x74
>> +
>> +#define SC27XX_WRITE_SELCLB_EN               BIT(0)
>> +#define SC27XX_FGU_CLBCNT_MASK               GENMASK(15, 0)
>> +#define SC27XX_FGU_CLBCNT_SHIFT              16
>> +
>> +#define SC27XX_FGU_1000MV_ADC                686
>> +#define SC27XX_FGU_1000MA_ADC                1372
>> +#define SC27XX_FGU_CUR_BASIC_ADC     8192
>> +#define SC27XX_FGU_SAMPLE_HZ         2
>> +
>> +/*
>> + * struct sc27xx_fgu_data: describe the FGU device
>> + * @regmap: regmap for register access
>> + * @dev: platform device
>> + * @battery: battery power supply
>> + * @base: the base offset for the controller
>> + * @lock: protect the structure
>> + * @gpiod: GPIO for battery detection
>> + * @channel: IIO channel to get battery temperature
>> + * @internal_resist: the battery internal resistance in mOhm
>> + * @total_cap: the total capacity of the battery in mAh
>> + * @init_cap: the initial capacity of the battery in mAh
>> + * @init_clbcnt: the initial coulomb counter
>> + * @max_volt: the maximum constant input voltage in millivolt
>> + * @table_len: the capacity table length
>> + * @cap_table: capacity table with corresponding ocv
>> + */
>> +struct sc27xx_fgu_data {
>> +     struct regmap *regmap;
>> +     struct device *dev;
>> +     struct power_supply *battery;
>> +     u32 base;
>> +     struct mutex lock;
>> +     struct gpio_desc *gpiod;
>> +     struct iio_channel *channel;
>> +     bool bat_present;
>> +     int internal_resist;
>> +     int total_cap;
>> +     int init_cap;
>> +     int init_clbcnt;
>> +     int max_volt;
>> +     int table_len;
>> +     struct power_supply_battery_ocv_table *cap_table;
>> +};
>> +
>> +static const char * const sc27xx_charger_supply_name[] = {
>> +     "sc2731_charger",
>> +     "sc2720_charger",
>> +     "sc2721_charger",
>> +     "sc2723_charger",
>> +};
>> +
>> +static int sc27xx_fgu_adc_to_current(int adc)
>> +{
>> +     return (adc * 1000) / SC27XX_FGU_1000MA_ADC;
>> +}
>> +
>> +static int sc27xx_fgu_adc_to_voltage(int adc)
>> +{
>> +     return (adc * 1000) / SC27XX_FGU_1000MV_ADC;
>> +}
>> +
>> +static int sc27xx_fgu_ocv_to_capacity(struct sc27xx_fgu_data *data, int ocv)
>> +{
>> +     struct power_supply_battery_ocv_table *tab = data->cap_table;
>> +     int n = data->table_len;
>> +     int i, cap, tmp;
>> +
>> +     /*
>> +      * Find the position in the table for current battery OCV value,
>> +      * then use these two points to calculate battery capacity
>> +      * according to the linear method.
>> +      */
>> +     for (i = 0; i < n; i++)
>> +             if (ocv > tab[i].ocv)
>> +                     break;
>> +
>> +     if (i > 0 && i < n) {
>> +             tmp = (tab[i - 1].capacity - tab[i].capacity) *
>> +                     (ocv - tab[i].ocv) * 2;
>> +             tmp /= tab[i - 1].ocv - tab[i].ocv;
>> +             tmp = (tmp + 1) / 2;
>> +             cap = tmp + tab[i].capacity;
>> +     } else if (i == 0) {
>> +             cap = tab[0].capacity;
>> +     } else {
>> +             cap = tab[n - 1].capacity;
>> +     }
>> +
>> +     return cap;
>> +}
>
> We should have a function working on the table(s) from battery_info
> instead, which can be shared by drivers. Maybe something like this:
>
> int ocv2cap_simple(struct power_supply_battery_ocv_table *table, int ocv)
> {
>     // basically your code but working with the common table
> }
>
> struct power_supply_battery_ocv_table *find_ocv2cap_table(struct power_supply_battery_info *info, int temp)
> {
>     int best_temp_diff, temp_diff = INT_MAX;
>     int best_index = 0;
>
>     for (int i=0; i < POWER_SUPPLY_OCV_TEMP_MAX; i++) {
>         temp_diff = abs(info->ocv_temp[i] - temp);
>         if (temp_diff < best_temp_diff) {
>             best_temp_diff = temp_diff;
>             best_index = i;
>         }
>     }
>
>     return &info->ocv_table[i];
> }
>
> int batinfo_ocv2cap(struct power_supply_battery_info *info, int ocv, int temp)
> {
>     struct power_supply_battery_ocv_table *table = find_ocv2cap_table(battery_info, temp);
>     return ocv2cap_simple(table, ocv);
> }

OK. Will add these helpers in next version.

>> +
>> +/*
>> + * When system boots on, we can not read battery capacity from coulomb
>> + * registers, since now the coulomb registers are invalid. So we should
>> + * calculate the battery open circuit voltage, and get current battery
>> + * capacity according to the capacity table.
>> + */
>> +static int sc27xx_fgu_get_boot_capacity(struct sc27xx_fgu_data *data, int *cap)
>> +{
>> +     int volt, cur, oci, ocv, ret;
>> +
>> +     /*
>> +      * After system booting on, the SC27XX_FGU_CLBCNT_QMAXL register saved
>> +      * the first sampled open circuit current.
>> +      */
>> +     ret = regmap_read(data->regmap, data->base + SC27XX_FGU_CLBCNT_QMAXL,
>> +                       &cur);
>> +     if (ret)
>> +             return ret;
>> +
>> +     cur <<= 1;
>> +     oci = sc27xx_fgu_adc_to_current(cur - SC27XX_FGU_CUR_BASIC_ADC);
>> +
>> +     /*
>> +      * Should get the OCV from SC27XX_FGU_POCV register at the system
>> +      * beginning. It is ADC values reading from registers which need to
>> +      * convert the corresponding voltage.
>> +      */
>> +     ret = regmap_read(data->regmap, data->base + SC27XX_FGU_POCV, &volt);
>> +     if (ret)
>> +             return ret;
>> +
>> +     volt = sc27xx_fgu_adc_to_voltage(volt);
>> +     ocv = volt - (oci * data->internal_resist) / 1000;
>> +
>> +     /*
>> +      * Parse the capacity table to look up the correct capacity percent
>> +      * according to current battery's corresponding OCV values.
>> +      */
>> +     *cap = sc27xx_fgu_ocv_to_capacity(data, ocv);
>> +
>> +     return 0;
>> +}
>> +
>> +static int sc27xx_fgu_set_clbcnt(struct sc27xx_fgu_data *data, int clbcnt)
>> +{
>> +     int ret;
>> +
>> +     clbcnt *= SC27XX_FGU_SAMPLE_HZ;
>> +
>> +     ret = regmap_update_bits(data->regmap,
>> +                              data->base + SC27XX_FGU_CLBCNT_SETL,
>> +                              SC27XX_FGU_CLBCNT_MASK, clbcnt);
>> +     if (ret)
>> +             return ret;
>> +
>> +     ret = regmap_update_bits(data->regmap,
>> +                              data->base + SC27XX_FGU_CLBCNT_SETH,
>> +                              SC27XX_FGU_CLBCNT_MASK,
>> +                              clbcnt >> SC27XX_FGU_CLBCNT_SHIFT);
>> +     if (ret)
>> +             return ret;
>> +
>> +     return regmap_update_bits(data->regmap, data->base + SC27XX_FGU_START,
>> +                              SC27XX_WRITE_SELCLB_EN,
>> +                              SC27XX_WRITE_SELCLB_EN);
>> +}
>> +
>> +static int sc27xx_fgu_get_clbcnt(struct sc27xx_fgu_data *data, int *clb_cnt)
>> +{
>> +     int ccl, cch, ret;
>> +
>> +     ret = regmap_read(data->regmap, data->base + SC27XX_FGU_CLBCNT_VALL,
>> +                       &ccl);
>> +     if (ret)
>> +             return ret;
>> +
>> +     ret = regmap_read(data->regmap, data->base + SC27XX_FGU_CLBCNT_VALH,
>> +                       &cch);
>> +     if (ret)
>> +             return ret;
>> +
>> +     *clb_cnt = ccl & SC27XX_FGU_CLBCNT_MASK;
>> +     *clb_cnt |= (cch & SC27XX_FGU_CLBCNT_MASK) << SC27XX_FGU_CLBCNT_SHIFT;
>> +     *clb_cnt /= SC27XX_FGU_SAMPLE_HZ;
>> +
>> +     return 0;
>> +}
>> +
>> +static int sc27xx_fgu_get_capacity(struct sc27xx_fgu_data *data, int *cap)
>> +{
>> +     int ret, cur_clbcnt, delta_clbcnt, delta_cap, temp;
>> +
>> +     /* Get current coulomb counters firstly */
>> +     ret = sc27xx_fgu_get_clbcnt(data, &cur_clbcnt);
>> +     if (ret)
>> +             return ret;
>> +
>> +     delta_clbcnt = cur_clbcnt - data->init_clbcnt;
>> +
>> +     /*
>> +      * Convert coulomb counter to delta capacity (mAh), and set multiplier
>> +      * as 100 to improve the precision.
>> +      */
>> +     temp = DIV_ROUND_CLOSEST(delta_clbcnt, 360);
>> +     temp = sc27xx_fgu_adc_to_current(temp);
>> +
>> +     /*
>> +      * Convert to capacity percent of the battery total capacity,
>> +      * and multiplier is 100 too.
>> +      */
>> +     delta_cap = DIV_ROUND_CLOSEST(temp * 100, data->total_cap);
>> +     *cap = delta_cap + data->init_cap;
>> +
>> +     return 0;
>> +}
>> +
>> +static int sc27xx_fgu_get_vbat_vol(struct sc27xx_fgu_data *data, int *val)
>> +{
>> +     int ret, vol;
>> +
>> +     ret = regmap_read(data->regmap, data->base + SC27XX_FGU_VOLTAGE, &vol);
>> +     if (ret)
>> +             return ret;
>> +
>> +     /*
>> +      * It is ADC values reading from registers which need to convert to
>> +      * corresponding voltage values.
>> +      */
>> +     *val = sc27xx_fgu_adc_to_voltage(vol);
>> +
>> +     return 0;
>> +}
>> +
>> +static int sc27xx_fgu_get_current(struct sc27xx_fgu_data *data, int *val)
>> +{
>> +     int ret, cur;
>> +
>> +     ret = regmap_read(data->regmap, data->base + SC27XX_FGU_CURRENT, &cur);
>> +     if (ret)
>> +             return ret;
>> +
>> +     /*
>> +      * It is ADC values reading from registers which need to convert to
>> +      * corresponding current values.
>> +      */
>> +     *val = sc27xx_fgu_adc_to_current(cur - SC27XX_FGU_CUR_BASIC_ADC);
>> +
>> +     return 0;
>> +}
>> +
>> +static int sc27xx_fgu_get_vbat_ocv(struct sc27xx_fgu_data *data, int *val)
>> +{
>> +     int vol, cur, ret;
>> +
>> +     ret = sc27xx_fgu_get_vbat_vol(data, &vol);
>> +     if (ret)
>> +             return ret;
>> +
>> +     ret = sc27xx_fgu_get_current(data, &cur);
>> +     if (ret)
>> +             return ret;
>> +
>> +     /* Return the battery OCV in micro volts. */
>> +     *val = vol * 1000 - cur * data->internal_resist;
>> +
>> +     return 0;
>> +}
>> +
>> +static int sc27xx_fgu_get_temp(struct sc27xx_fgu_data *data, int *temp)
>> +{
>> +     return iio_read_channel_processed(data->channel, temp);
>> +}
>> +
>> +static int sc27xx_fgu_get_health(struct sc27xx_fgu_data *data, int *health)
>> +{
>> +     int ret, vol;
>> +
>> +     ret = sc27xx_fgu_get_vbat_vol(data, &vol);
>> +     if (ret)
>> +             return ret;
>> +
>> +     if (vol > data->max_volt)
>> +             *health = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
>> +     else
>> +             *health = POWER_SUPPLY_HEALTH_GOOD;
>> +
>> +     return 0;
>> +}
>> +
>> +static int sc27xx_fgu_get_status(struct sc27xx_fgu_data *data, int *status)
>> +{
>> +     union power_supply_propval val;
>> +     struct power_supply *psy;
>> +     int i, ret = -EINVAL;
>> +
>> +     for (i = 0; i < ARRAY_SIZE(sc27xx_charger_supply_name); i++) {
>> +             psy = power_supply_get_by_name(sc27xx_charger_supply_name[i]);
>> +             if (!psy)
>> +                     continue;
>> +
>> +             ret = power_supply_get_property(psy, POWER_SUPPLY_PROP_STATUS,
>> +                                             &val);
>> +             power_supply_put(psy);
>> +             if (ret)
>> +                     return ret;
>> +
>> +             *status = val.intval;
>> +     }
>> +
>> +     return ret;
>> +}
>> +
>> +static int sc27xx_fgu_get_property(struct power_supply *psy,
>> +                                enum power_supply_property psp,
>> +                                union power_supply_propval *val)
>> +{
>> +     struct sc27xx_fgu_data *data = power_supply_get_drvdata(psy);
>> +     int ret = 0;
>> +     int value;
>> +
>> +     mutex_lock(&data->lock);
>> +
>> +     switch (psp) {
>> +     case POWER_SUPPLY_PROP_STATUS:
>> +             ret = sc27xx_fgu_get_status(data, &value);
>> +             if (ret)
>> +                     goto error;
>> +
>> +             val->intval = value;
>> +             break;
>> +
>> +     case POWER_SUPPLY_PROP_HEALTH:
>> +             ret = sc27xx_fgu_get_health(data, &value);
>> +             if (ret)
>> +                     goto error;
>> +
>> +             val->intval = value;
>> +             break;
>> +
>> +     case POWER_SUPPLY_PROP_PRESENT:
>> +             val->intval = data->bat_present;
>> +             break;
>> +
>> +     case POWER_SUPPLY_PROP_TEMP:
>> +             ret = sc27xx_fgu_get_temp(data, &value);
>> +             if (ret)
>> +                     goto error;
>> +
>> +             val->intval = value;
>> +             break;
>> +
>> +     case POWER_SUPPLY_PROP_TECHNOLOGY:
>> +             val->intval = POWER_SUPPLY_TECHNOLOGY_LION;
>> +             break;
>> +
>> +     case POWER_SUPPLY_PROP_CAPACITY:
>> +             ret = sc27xx_fgu_get_capacity(data, &value);
>> +             if (ret)
>> +                     goto error;
>> +
>> +             val->intval = value;
>> +             break;
>> +
>> +     case POWER_SUPPLY_PROP_VOLTAGE_NOW:
>> +             ret = sc27xx_fgu_get_vbat_vol(data, &value);
>> +             if (ret)
>> +                     goto error;
>> +
>> +             val->intval = value * 1000;
>> +             break;
>> +
>> +     case POWER_SUPPLY_PROP_VOLTAGE_OCV:
>> +             ret = sc27xx_fgu_get_vbat_ocv(data, &value);
>> +             if (ret)
>> +                     goto error;
>> +
>> +             val->intval = value;
>> +             break;
>> +
>> +     case POWER_SUPPLY_PROP_CURRENT_NOW:
>> +     case POWER_SUPPLY_PROP_CURRENT_AVG:
>> +             ret = sc27xx_fgu_get_current(data, &value);
>> +             if (ret)
>> +                     goto error;
>> +
>> +             val->intval = value * 1000;
>> +             break;
>> +
>> +     default:
>> +             ret = -EINVAL;
>> +             break;
>> +     }
>> +
>> +error:
>> +     mutex_unlock(&data->lock);
>> +     return ret;
>> +}
>> +
>> +static void sc27xx_fgu_external_power_changed(struct power_supply *psy)
>> +{
>> +     struct sc27xx_fgu_data *data = power_supply_get_drvdata(psy);
>> +
>> +     power_supply_changed(data->battery);
>> +}
>> +
>> +static enum power_supply_property sc27xx_fgu_props[] = {
>> +     POWER_SUPPLY_PROP_STATUS,
>> +     POWER_SUPPLY_PROP_HEALTH,
>> +     POWER_SUPPLY_PROP_PRESENT,
>> +     POWER_SUPPLY_PROP_TEMP,
>> +     POWER_SUPPLY_PROP_TECHNOLOGY,
>> +     POWER_SUPPLY_PROP_CAPACITY,
>> +     POWER_SUPPLY_PROP_VOLTAGE_NOW,
>> +     POWER_SUPPLY_PROP_VOLTAGE_OCV,
>> +     POWER_SUPPLY_PROP_CURRENT_NOW,
>> +     POWER_SUPPLY_PROP_CURRENT_AVG,
>> +};
>> +
>> +static const struct power_supply_desc sc27xx_fgu_desc = {
>> +     .name                   = "sc27xx-fgu",
>> +     .type                   = POWER_SUPPLY_TYPE_BATTERY,
>> +     .properties             = sc27xx_fgu_props,
>> +     .num_properties         = ARRAY_SIZE(sc27xx_fgu_props),
>> +     .get_property           = sc27xx_fgu_get_property,
>> +     .external_power_changed = sc27xx_fgu_external_power_changed,
>> +};
>> +
>> +static irqreturn_t sc27xx_fgu_bat_detection(int irq, void *dev_id)
>> +{
>> +     struct sc27xx_fgu_data *data = dev_id;
>> +     int state;
>> +
>> +     mutex_lock(&data->lock);
>> +
>> +     state = gpiod_get_value_cansleep(data->gpiod);
>> +     if (state < 0) {
>> +             dev_err(data->dev, "failed to get gpio state\n");
>> +             mutex_unlock(&data->lock);
>> +             return IRQ_RETVAL(state);
>> +     }
>> +
>> +     data->bat_present = !!state;
>> +
>> +     mutex_unlock(&data->lock);
>> +
>> +     power_supply_changed(data->battery);
>> +     return IRQ_HANDLED;
>> +}
>> +
>> +static void sc27xx_fgu_disable(void *_data)
>> +{
>> +     struct sc27xx_fgu_data *data = _data;
>> +
>> +     regmap_update_bits(data->regmap, SC27XX_CLK_EN0, SC27XX_FGU_RTC_EN, 0);
>> +     regmap_update_bits(data->regmap, SC27XX_MODULE_EN0, SC27XX_FGU_EN, 0);
>> +}
>> +
>> +static int sc27xx_fgu_cap_to_clbcnt(struct sc27xx_fgu_data *data, int capacity)
>> +{
>> +     /*
>> +      * Get current capacity (mAh) = battery total capacity (mAh) *
>> +      * current capacity percent (capacity / 100).
>> +      */
>> +     int cur_cap = DIV_ROUND_CLOSEST(data->total_cap * capacity, 100);
>> +
>> +     /*
>> +      * Convert current capacity (mAh) to coulomb counter according to the
>> +      * formula: 1 mAh =3.6 coulomb.
>> +      */
>> +     return DIV_ROUND_CLOSEST(cur_cap * 36, 10);
>> +}
>> +
>> +static int sc27xx_fgu_hw_init(struct sc27xx_fgu_data *data)
>> +{
>> +     struct power_supply_battery_info info = { };
>> +     struct power_supply_battery_ocv_table *table;
>> +     int ret, i;
>> +
>> +     ret = power_supply_get_battery_info(data->battery, &info);
>> +     if (ret) {
>> +             dev_err(data->dev, "failed to get battery information\n");
>> +             return ret;
>> +     }
>> +
>> +     data->total_cap = info.charge_full_design_uah / 1000;
>> +     data->max_volt = info.constant_charge_voltage_max_uv / 1000;
>> +     data->internal_resist = info.internal_resistance_uohm / 1000;
>> +     data->table_len = info.ocv_table_size[0];
>> +
>> +     /*
>> +      * For SC27XX fuel gauge device, we only need one ocv-capacity
>> +      * table in normal temperature.
>> +      */
>> +     table = info.ocv_table[0];
>> +     if (!table)
>> +             return -EINVAL;
>> +
>> +     data->cap_table = devm_kzalloc(data->dev,
>> +                                    data->table_len * sizeof(*table),
>> +                                    GFP_KERNEL);
>> +     if (!data->cap_table) {
>> +             power_supply_put_battery_info(data->battery, &info);
>> +             return -ENOMEM;
>> +     }
>> +
>> +     for (i = 0; i < data->table_len; i++) {
>> +             data->cap_table[i].ocv = table[i].ocv / 1000;
>> +             data->cap_table[i].capacity = table[i].capacity;
>> +     }
>> +
>> +     power_supply_put_battery_info(data->battery, &info);
>> +
>> +     /* Enable the FGU module */
>> +     ret = regmap_update_bits(data->regmap, SC27XX_MODULE_EN0,
>> +                              SC27XX_FGU_EN, SC27XX_FGU_EN);
>> +     if (ret) {
>> +             dev_err(data->dev, "failed to enable fgu\n");
>> +             return ret;
>> +     }
>> +
>> +     /* Enable the FGU RTC clock to make it work */
>> +     ret = regmap_update_bits(data->regmap, SC27XX_CLK_EN0,
>> +                              SC27XX_FGU_RTC_EN, SC27XX_FGU_RTC_EN);
>> +     if (ret) {
>> +             dev_err(data->dev, "failed to enable fgu RTC clock\n");
>> +             goto disable_fgu;
>> +     }
>> +
>> +     /*
>> +      * Get the boot battery capacity when system powers on, which is used to
>> +      * initialize the coulomb counter. After that, we can read the coulomb
>> +      * counter to measure the battery capacity.
>> +      */
>> +     ret = sc27xx_fgu_get_boot_capacity(data, &data->init_cap);
>> +     if (ret) {
>> +             dev_err(data->dev, "failed to get boot capacity\n");
>> +             goto disable_clk;
>> +     }
>> +
>> +     /*
>> +      * Convert battery capacity to the corresponding initial coulomb counter
>> +      * and set into coulomb counter registers.
>> +      */
>> +     data->init_clbcnt = sc27xx_fgu_cap_to_clbcnt(data, data->init_cap);
>> +     ret = sc27xx_fgu_set_clbcnt(data, data->init_clbcnt);
>> +     if (ret) {
>> +             dev_err(data->dev, "failed to initialize coulomb counter\n");
>> +             goto disable_clk;
>> +     }
>> +
>> +     return 0;
>> +
>> +disable_clk:
>> +     regmap_update_bits(data->regmap, SC27XX_CLK_EN0, SC27XX_FGU_RTC_EN, 0);
>> +disable_fgu:
>> +     regmap_update_bits(data->regmap, SC27XX_MODULE_EN0, SC27XX_FGU_EN, 0);
>> +
>> +     return ret;
>> +}
>> +
>> +static int sc27xx_fgu_probe(struct platform_device *pdev)
>> +{
>> +     struct device_node *np = pdev->dev.of_node;
>> +     struct power_supply_config fgu_cfg = { };
>> +     struct sc27xx_fgu_data *data;
>> +     int ret, irq;
>> +
>> +     data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
>> +     if (!data)
>> +             return -ENOMEM;
>> +
>> +     data->regmap = dev_get_regmap(pdev->dev.parent, NULL);
>> +     if (!data->regmap) {
>> +             dev_err(&pdev->dev, "failed to get regmap\n");
>> +             return -ENODEV;
>> +     }
>> +
>> +     ret = of_property_read_u32(np, "reg", &data->base);
>> +     if (ret) {
>> +             dev_err(&pdev->dev, "failed to get fgu address\n");
>> +             return ret;
>> +     }
>
> Can you please use device_property_read_u32() instead.
> If I didn't miss anything you can drop #include <linux/of.h> afterwards.

Sure. Thanks.

>
> -- Sebastian
>
>> +     data->channel = devm_iio_channel_get(&pdev->dev, "bat-temp");
>> +     if (IS_ERR(data->channel)) {
>> +             dev_err(&pdev->dev, "failed to get IIO channel\n");
>> +             return PTR_ERR(data->channel);
>> +     }
>> +
>> +     data->gpiod = devm_gpiod_get(&pdev->dev, "bat-detect", GPIOD_IN);
>> +     if (IS_ERR(data->gpiod)) {
>> +             dev_err(&pdev->dev, "failed to get battery detection GPIO\n");
>> +             return PTR_ERR(data->gpiod);
>> +     }
>> +
>> +     ret = gpiod_get_value_cansleep(data->gpiod);
>> +     if (ret < 0) {
>> +             dev_err(&pdev->dev, "failed to get gpio state\n");
>> +             return ret;
>> +     }
>> +
>> +     data->bat_present = !!ret;
>> +     mutex_init(&data->lock);
>> +     data->dev = &pdev->dev;
>> +
>> +     fgu_cfg.drv_data = data;
>> +     fgu_cfg.of_node = np;
>> +     data->battery = devm_power_supply_register(&pdev->dev, &sc27xx_fgu_desc,
>> +                                                &fgu_cfg);
>> +     if (IS_ERR(data->battery)) {
>> +             dev_err(&pdev->dev, "failed to register power supply\n");
>> +             return PTR_ERR(data->battery);
>> +     }
>> +
>> +     ret = sc27xx_fgu_hw_init(data);
>> +     if (ret) {
>> +             dev_err(&pdev->dev, "failed to initialize fgu hardware\n");
>> +             return ret;
>> +     }
>> +
>> +     ret = devm_add_action(&pdev->dev, sc27xx_fgu_disable, data);
>> +     if (ret) {
>> +             sc27xx_fgu_disable(data);
>> +             dev_err(&pdev->dev, "failed to add fgu disable action\n");
>> +             return ret;
>> +     }
>> +
>> +     irq = gpiod_to_irq(data->gpiod);
>> +     if (irq < 0) {
>> +             dev_err(&pdev->dev, "failed to translate GPIO to IRQ\n");
>> +             return irq;
>> +     }
>> +
>> +     ret = devm_request_threaded_irq(&pdev->dev, irq, NULL,
>> +                                     sc27xx_fgu_bat_detection,
>> +                                     IRQF_ONESHOT | IRQF_TRIGGER_RISING |
>> +                                     IRQF_TRIGGER_FALLING,
>> +                                     pdev->name, data);
>> +     if (ret) {
>> +             dev_err(&pdev->dev, "failed to request IRQ\n");
>> +             return ret;
>> +     }
>> +
>> +     return 0;
>> +}
>> +
>> +static const struct of_device_id sc27xx_fgu_of_match[] = {
>> +     { .compatible = "sprd,sc2731-fgu", },
>> +     { }
>> +};
>> +
>> +static struct platform_driver sc27xx_fgu_driver = {
>> +     .probe = sc27xx_fgu_probe,
>> +     .driver = {
>> +             .name = "sc27xx-fgu",
>> +             .of_match_table = sc27xx_fgu_of_match,
>> +     }
>> +};
>> +
>> +module_platform_driver(sc27xx_fgu_driver);
>> +
>> +MODULE_DESCRIPTION("Spreadtrum SC27XX PMICs Fual Gauge Unit Driver");
>> +MODULE_LICENSE("GPL v2");



-- 
Baolin Wang
Best Regards