From: Lee Jones <lee.jones@linaro.org>
To: Alistair Francis <alistair23@gmail.com>
Cc: Alistair Francis <alistair@alistair23.me>,
Rob Herring <robh+dt@kernel.org>,
lgirdwood@gmail.com, Mark Brown <broonie@kernel.org>,
dl-linux-imx <linux-imx@nxp.com>,
Sascha Hauer <kernel@pengutronix.de>,
devicetree <devicetree@vger.kernel.org>,
Linux Kernel Mailing List <linux-kernel@vger.kernel.org>,
Lars Ivar Miljeteig <lars.ivar.miljeteig@remarkable.no>
Subject: Re: [PATCH v7 2/6] thermal: sy7636a: Add thermal driver for sy7636a
Date: Mon, 2 Aug 2021 08:55:33 +0100 [thread overview]
Message-ID: <YQek9afLXShHl2YI@google.com> (raw)
In-Reply-To: <CAKmqyKPk5mksq7KK0FOBLLLyw+3o52EjtkqOMe0tMg5OgxOkJw@mail.gmail.com>
On Wed, 28 Jul 2021, Alistair Francis wrote:
> On Wed, Jul 21, 2021 at 1:02 AM Lee Jones <lee.jones@linaro.org> wrote:
> >
> > On Thu, 08 Jul 2021, Alistair Francis wrote:
> >
> > > From: Lars Ivar Miljeteig <lars.ivar.miljeteig@remarkable.no>
> > >
> > > Add thermal driver to enable kernel based polling
> > > and shutdown of device for temperatures out of spec
> > >
> > > Signed-off-by: Alistair Francis <alistair@alistair23.me>
> > > ---
> > > drivers/thermal/Kconfig | 7 ++
> > > drivers/thermal/Makefile | 1 +
> > > drivers/thermal/sy7636a_thermal.c | 107 ++++++++++++++++++++++++++++++
> > > 3 files changed, 115 insertions(+)
> > > create mode 100644 drivers/thermal/sy7636a_thermal.c
> > >
> > > diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
> > > index d7f44deab5b1..7112c63d9021 100644
> > > --- a/drivers/thermal/Kconfig
> > > +++ b/drivers/thermal/Kconfig
> > > @@ -450,6 +450,13 @@ depends on (ARCH_STI || ARCH_STM32) && OF
> > > source "drivers/thermal/st/Kconfig"
> > > endmenu
> > >
> > > +config SY7636A_THERMAL
> > > + tristate "SY7636A thermal management"
> > > + depends on MFD_SY7636A
> > > + help
> > > + Enable the sy7636a thermal driver, which supports the
> > > + temperature sensor embedded in Silabs SY7636A chip.
> > > +
> > > source "drivers/thermal/tegra/Kconfig"
> > >
> > > config GENERIC_ADC_THERMAL
> > > diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
> > > index 82fc3e616e54..2e1aca8a0a09 100644
> > > --- a/drivers/thermal/Makefile
> > > +++ b/drivers/thermal/Makefile
> > > @@ -51,6 +51,7 @@ obj-$(CONFIG_DA9062_THERMAL) += da9062-thermal.o
> > > obj-y += intel/
> > > obj-$(CONFIG_TI_SOC_THERMAL) += ti-soc-thermal/
> > > obj-y += st/
> > > +obj-$(CONFIG_SY7636A_THERMAL) += sy7636a_thermal.o
> > > obj-$(CONFIG_QCOM_TSENS) += qcom/
> > > obj-y += tegra/
> > > obj-$(CONFIG_HISI_THERMAL) += hisi_thermal.o
> > > diff --git a/drivers/thermal/sy7636a_thermal.c b/drivers/thermal/sy7636a_thermal.c
> > > new file mode 100644
> > > index 000000000000..705a16fb1045
> > > --- /dev/null
> > > +++ b/drivers/thermal/sy7636a_thermal.c
> > > @@ -0,0 +1,107 @@
> > > +// SPDX-License-Identifier: GPL-2.0+
> > > +//
> > > +// Functions to access SY3686A power management chip temperature
> > > +//
> > > +// Copyright (C) 2019 reMarkable AS - http://www.remarkable.com/
> > > +//
> > > +// Authors: Lars Ivar Miljeteig <lars.ivar.miljeteig@remarkable.com>
> > > +// Alistair Francis <alistair@alistair23.me>
> > > +
> > > +#include <linux/module.h>
> > > +#include <linux/platform_device.h>
> > > +#include <linux/thermal.h>
> > > +
> > > +#include <linux/mfd/sy7636a.h>
> > > +
> > > +struct sy7636a_data {
> > > + struct sy7636a *sy7636a;
> > > + struct thermal_zone_device *thermal_zone_dev;
> > > +};
> > > +
> > > +static int sy7636a_get_temp(void *arg, int *res)
> > > +{
> > > + unsigned int reg_val, mode_ctr;
> > > + int ret;
> > > + struct sy7636a_data *data = arg;
> > > + bool isVoltageActive;
> > > +
> > > + ret = regmap_read(data->sy7636a->regmap,
> > > + SY7636A_REG_OPERATION_MODE_CRL, &mode_ctr);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + isVoltageActive = mode_ctr & SY7636A_OPERATION_MODE_CRL_ONOFF;
> > > +
> > > + if (!isVoltageActive) {
> > > + ret = regmap_write(data->sy7636a->regmap,
> > > + SY7636A_REG_OPERATION_MODE_CRL,
> > > + mode_ctr | SY7636A_OPERATION_MODE_CRL_ONOFF);
> > > + if (ret)
> > > + return ret;
> > > + }
> > > +
> > > + ret = regmap_read(data->sy7636a->regmap,
> > > + SY7636A_REG_TERMISTOR_READOUT, ®_val);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + if (!isVoltageActive) {
> > > + ret = regmap_write(data->sy7636a->regmap,
> > > + SY7636A_REG_OPERATION_MODE_CRL,
> > > + mode_ctr);
> > > + if (ret)
> > > + return ret;
> > > + }
> > > +
> > > + *res = *((signed char*)®_val);
> > > + *res *= 1000;
> > > +
> > > + return ret;
> > > +}
> > > +
> > > +static const struct thermal_zone_of_device_ops ops = {
> > > + .get_temp = sy7636a_get_temp,
> > > +};
> > > +
> > > +static int sy7636a_thermal_probe(struct platform_device *pdev)
> > > +{
> > > + struct sy7636a *sy7636a = dev_get_drvdata(pdev->dev.parent);
> > > + struct sy7636a_data *data;
> > > +
> > > + if (!sy7636a)
> > > + return -EPROBE_DEFER;
> >
> > How is this possible?
>
> I'm not sure, I have removed this.
>
> >
> > > + data = devm_kzalloc(&pdev->dev, sizeof(struct sy7636a_data), GFP_KERNEL);
> >
> > sizeof(*data)
> >
> > > + if (!data)
> > > + return -ENOMEM;
> > > +
> > > + platform_set_drvdata(pdev, data);
> > > +
> > > + data->sy7636a = sy7636a;
> > > + data->thermal_zone_dev = devm_thermal_zone_of_sensor_register(
> > > + pdev->dev.parent,
> > > + 0,
> > > + data,
> >
> > Why don't you just pass in your initial ddata?
>
> I'm not sure what you mean, which data?
sy7636a
--
Lee Jones [李琼斯]
Senior Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog
next prev parent reply other threads:[~2021-08-02 7:55 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-07-08 11:57 [PATCH v7 1/6] mfd: sy7636a: Initial commit Alistair Francis
2021-07-08 11:58 ` [PATCH v7 2/6] thermal: sy7636a: Add thermal driver for sy7636a Alistair Francis
2021-07-20 15:02 ` Lee Jones
2021-07-28 8:23 ` Alistair Francis
2021-08-02 7:55 ` Lee Jones [this message]
2021-08-14 11:08 ` Daniel Lezcano
2021-07-08 11:58 ` [PATCH v7 3/6] hwmon: sy7636a: Add temperature " Alistair Francis
2021-07-20 14:59 ` Lee Jones
2021-08-02 9:48 ` Alistair Francis
2021-07-08 11:58 ` [PATCH v7 4/6] ARM: imx_v6_v7_defconfig: Enable silergy,sy7636a Alistair Francis
2021-07-08 11:58 ` [PATCH v7 5/6] ARM: dts: imx7d: remarkable2: " Alistair Francis
2021-07-08 11:58 ` [PATCH v7 6/6] ARM: dts: imx7d: remarkable2: Enable lcdif Alistair Francis
2021-07-20 14:53 ` [PATCH v7 1/6] mfd: sy7636a: Initial commit Lee Jones
2021-07-20 15:23 ` Mark Brown
2021-07-20 16:09 ` Lee Jones
2021-07-20 20:26 ` Mark Brown
2021-07-30 6:21 ` Alistair Francis
2021-07-30 11:13 ` Mark Brown
2021-08-02 9:26 ` Alistair Francis
2021-08-02 10:23 ` Lee Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=YQek9afLXShHl2YI@google.com \
--to=lee.jones@linaro.org \
--cc=alistair23@gmail.com \
--cc=alistair@alistair23.me \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=kernel@pengutronix.de \
--cc=lars.ivar.miljeteig@remarkable.no \
--cc=lgirdwood@gmail.com \
--cc=linux-imx@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).