* Re: [PATCH] clk: qcom: sc8280xp: add parent to gcc_ufs_phy_axi_clk for sa8540p
2022-06-23 14:28 [PATCH] clk: qcom: sc8280xp: add parent to gcc_ufs_phy_axi_clk for sa8540p Brian Masney
@ 2022-06-23 15:32 ` Andrew Halaney
2022-06-23 17:13 ` Brian Masney
2022-06-24 0:20 ` Stephen Boyd
2022-07-16 14:54 ` Bjorn Andersson
2 siblings, 1 reply; 8+ messages in thread
From: Andrew Halaney @ 2022-06-23 15:32 UTC (permalink / raw)
To: Brian Masney
Cc: bjorn.andersson, linux-arm-msm, agross, mturquette, sboyd,
linux-clk, linux-kernel, echanude
On Thu, Jun 23, 2022 at 10:28:37AM -0400, Brian Masney wrote:
> The sa8540p automotive board has the same SOC as the sc8280xp. In order
> to get the first UFS controller working on the sa8540p,
> GCC_UFS_REF_CLKREF_CLK needs to be setup as a parent to
> GCC_UFS_PHY_AXI_CLK.
>
> This clock name came from the DTS for the downstream MSM 5.4 kernel
> sources for the sa8540p. It also references GCC_UFS_CARD_CLKREF_CLK,
> however that wasn't needed to get the first UFS controller working.
>
I'm not knowledgable enough on the clock subsystem or have access to
documentation to comment on correctness outside of the 5.4 MSM kernel
you mentioned, but I think this probably deserves a Fixes: tag?
I can at least also comment that without this change the sa8540p doesn't
boot on the QDrive3 boards we have.
Thanks,
Andrew
> Signed-off-by: Brian Masney <bmasney@redhat.com>
> ---
> I originally added this under GCC_UFS_PHY_PHY_AUX_CLK since that's
> what's in the downstream DTS. I was getting errors about
> GCC_UFS_PHY_AXI_CLK being stuck at off so I moved it there.
>
> Also I don't have access to any documentation for this board so I'm
> hoping that someone with docs access can verify that this is the
> appropriate place to put this.
>
> drivers/clk/qcom/gcc-sc8280xp.c | 27 ++++++++++++++-------------
> 1 file changed, 14 insertions(+), 13 deletions(-)
>
> diff --git a/drivers/clk/qcom/gcc-sc8280xp.c b/drivers/clk/qcom/gcc-sc8280xp.c
> index 4b894442fdf5..4639b50da418 100644
> --- a/drivers/clk/qcom/gcc-sc8280xp.c
> +++ b/drivers/clk/qcom/gcc-sc8280xp.c
> @@ -5685,6 +5685,19 @@ static struct clk_branch gcc_ufs_phy_ahb_clk = {
> },
> };
>
> +static struct clk_branch gcc_ufs_ref_clkref_clk = {
> + .halt_reg = 0x8c058,
> + .halt_check = BRANCH_HALT,
> + .clkr = {
> + .enable_reg = 0x8c058,
> + .enable_mask = BIT(0),
> + .hw.init = &(const struct clk_init_data) {
> + .name = "gcc_ufs_ref_clkref_clk",
> + .ops = &clk_branch2_ops,
> + },
> + },
> +};
> +
> static struct clk_branch gcc_ufs_phy_axi_clk = {
> .halt_reg = 0x77010,
> .halt_check = BRANCH_HALT_VOTED,
> @@ -5696,6 +5709,7 @@ static struct clk_branch gcc_ufs_phy_axi_clk = {
> .hw.init = &(const struct clk_init_data) {
> .name = "gcc_ufs_phy_axi_clk",
> .parent_hws = (const struct clk_hw*[]){
> + &gcc_ufs_ref_clkref_clk.clkr.hw,
> &gcc_ufs_phy_axi_clk_src.clkr.hw,
> },
> .num_parents = 1,
> @@ -5899,19 +5913,6 @@ static struct clk_branch gcc_ufs_phy_unipro_core_hw_ctl_clk = {
> },
> };
>
> -static struct clk_branch gcc_ufs_ref_clkref_clk = {
> - .halt_reg = 0x8c058,
> - .halt_check = BRANCH_HALT,
> - .clkr = {
> - .enable_reg = 0x8c058,
> - .enable_mask = BIT(0),
> - .hw.init = &(const struct clk_init_data) {
> - .name = "gcc_ufs_ref_clkref_clk",
> - .ops = &clk_branch2_ops,
> - },
> - },
> -};
> -
> static struct clk_branch gcc_usb2_hs0_clkref_clk = {
> .halt_reg = 0x8c044,
> .halt_check = BRANCH_HALT,
> --
> 2.36.1
>
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH] clk: qcom: sc8280xp: add parent to gcc_ufs_phy_axi_clk for sa8540p
2022-06-23 15:32 ` Andrew Halaney
@ 2022-06-23 17:13 ` Brian Masney
0 siblings, 0 replies; 8+ messages in thread
From: Brian Masney @ 2022-06-23 17:13 UTC (permalink / raw)
To: Andrew Halaney
Cc: bjorn.andersson, linux-arm-msm, agross, mturquette, sboyd,
linux-clk, linux-kernel, echanude
On Thu, Jun 23, 2022 at 10:32:26AM -0500, Andrew Halaney wrote:
> I'm not knowledgable enough on the clock subsystem or have access to
> documentation to comment on correctness outside of the 5.4 MSM kernel
> you mentioned, but I think this probably deserves a Fixes: tag?
Good call!
Fixes: d65d005f9a6c ("clk: qcom: add sc8280xp GCC driver")
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH] clk: qcom: sc8280xp: add parent to gcc_ufs_phy_axi_clk for sa8540p
2022-06-23 14:28 [PATCH] clk: qcom: sc8280xp: add parent to gcc_ufs_phy_axi_clk for sa8540p Brian Masney
2022-06-23 15:32 ` Andrew Halaney
@ 2022-06-24 0:20 ` Stephen Boyd
2022-06-24 16:40 ` Brian Masney
2022-07-16 14:54 ` Bjorn Andersson
2 siblings, 1 reply; 8+ messages in thread
From: Stephen Boyd @ 2022-06-24 0:20 UTC (permalink / raw)
To: Brian Masney, bjorn.andersson, linux-arm-msm
Cc: agross, mturquette, linux-clk, linux-kernel, ahalaney, echanude
Quoting Brian Masney (2022-06-23 07:28:37)
> diff --git a/drivers/clk/qcom/gcc-sc8280xp.c b/drivers/clk/qcom/gcc-sc8280xp.c
> index 4b894442fdf5..4639b50da418 100644
> --- a/drivers/clk/qcom/gcc-sc8280xp.c
> +++ b/drivers/clk/qcom/gcc-sc8280xp.c
> @@ -5696,6 +5709,7 @@ static struct clk_branch gcc_ufs_phy_axi_clk = {
> .hw.init = &(const struct clk_init_data) {
> .name = "gcc_ufs_phy_axi_clk",
> .parent_hws = (const struct clk_hw*[]){
> + &gcc_ufs_ref_clkref_clk.clkr.hw,
> &gcc_ufs_phy_axi_clk_src.clkr.hw,
> },
> .num_parents = 1,
num_parents needs an update. But this is a branch, not a mux, so it
can't have more than one parent.
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH] clk: qcom: sc8280xp: add parent to gcc_ufs_phy_axi_clk for sa8540p
2022-06-24 0:20 ` Stephen Boyd
@ 2022-06-24 16:40 ` Brian Masney
2022-06-24 20:16 ` Stephen Boyd
0 siblings, 1 reply; 8+ messages in thread
From: Brian Masney @ 2022-06-24 16:40 UTC (permalink / raw)
To: Stephen Boyd
Cc: bjorn.andersson, linux-arm-msm, agross, mturquette, linux-clk,
linux-kernel, ahalaney, echanude
On Thu, Jun 23, 2022 at 05:20:53PM -0700, Stephen Boyd wrote:
> Quoting Brian Masney (2022-06-23 07:28:37)
> > diff --git a/drivers/clk/qcom/gcc-sc8280xp.c b/drivers/clk/qcom/gcc-sc8280xp.c
> > index 4b894442fdf5..4639b50da418 100644
> > --- a/drivers/clk/qcom/gcc-sc8280xp.c
> > +++ b/drivers/clk/qcom/gcc-sc8280xp.c
> > @@ -5696,6 +5709,7 @@ static struct clk_branch gcc_ufs_phy_axi_clk = {
> > .hw.init = &(const struct clk_init_data) {
> > .name = "gcc_ufs_phy_axi_clk",
> > .parent_hws = (const struct clk_hw*[]){
> > + &gcc_ufs_ref_clkref_clk.clkr.hw,
> > &gcc_ufs_phy_axi_clk_src.clkr.hw,
> > },
> > .num_parents = 1,
>
> num_parents needs an update.
Oops!
> But this is a branch, not a mux, so it can't have more than one
> parent.
Would a mux be represented with 'struct clk_rcg2'?
Brian
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH] clk: qcom: sc8280xp: add parent to gcc_ufs_phy_axi_clk for sa8540p
2022-06-24 16:40 ` Brian Masney
@ 2022-06-24 20:16 ` Stephen Boyd
0 siblings, 0 replies; 8+ messages in thread
From: Stephen Boyd @ 2022-06-24 20:16 UTC (permalink / raw)
To: Brian Masney
Cc: bjorn.andersson, linux-arm-msm, agross, mturquette, linux-clk,
linux-kernel, ahalaney, echanude
Quoting Brian Masney (2022-06-24 09:40:26)
> On Thu, Jun 23, 2022 at 05:20:53PM -0700, Stephen Boyd wrote:
> > Quoting Brian Masney (2022-06-23 07:28:37)
> > > diff --git a/drivers/clk/qcom/gcc-sc8280xp.c b/drivers/clk/qcom/gcc-sc8280xp.c
> > > index 4b894442fdf5..4639b50da418 100644
> > > --- a/drivers/clk/qcom/gcc-sc8280xp.c
> > > +++ b/drivers/clk/qcom/gcc-sc8280xp.c
> > > @@ -5696,6 +5709,7 @@ static struct clk_branch gcc_ufs_phy_axi_clk = {
> > > .hw.init = &(const struct clk_init_data) {
> > > .name = "gcc_ufs_phy_axi_clk",
> > > .parent_hws = (const struct clk_hw*[]){
> > > + &gcc_ufs_ref_clkref_clk.clkr.hw,
> > > &gcc_ufs_phy_axi_clk_src.clkr.hw,
> > > },
> > > .num_parents = 1,
> >
> > num_parents needs an update.
>
> Oops!
>
> > But this is a branch, not a mux, so it can't have more than one
> > parent.
>
> Would a mux be represented with 'struct clk_rcg2'?
>
Could be. An RCG is more than a mux, because it also has a divider and
an m/n counter.
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH] clk: qcom: sc8280xp: add parent to gcc_ufs_phy_axi_clk for sa8540p
2022-06-23 14:28 [PATCH] clk: qcom: sc8280xp: add parent to gcc_ufs_phy_axi_clk for sa8540p Brian Masney
2022-06-23 15:32 ` Andrew Halaney
2022-06-24 0:20 ` Stephen Boyd
@ 2022-07-16 14:54 ` Bjorn Andersson
2022-07-19 18:49 ` Brian Masney
2 siblings, 1 reply; 8+ messages in thread
From: Bjorn Andersson @ 2022-07-16 14:54 UTC (permalink / raw)
To: Brian Masney
Cc: linux-arm-msm, agross, mturquette, sboyd, linux-clk,
linux-kernel, ahalaney, echanude
On Thu 23 Jun 09:28 CDT 2022, Brian Masney wrote:
> The sa8540p automotive board has the same SOC as the sc8280xp. In order
> to get the first UFS controller working on the sa8540p,
> GCC_UFS_REF_CLKREF_CLK needs to be setup as a parent to
> GCC_UFS_PHY_AXI_CLK.
>
> This clock name came from the DTS for the downstream MSM 5.4 kernel
> sources for the sa8540p. It also references GCC_UFS_CARD_CLKREF_CLK,
> however that wasn't needed to get the first UFS controller working.
>
> Signed-off-by: Brian Masney <bmasney@redhat.com>
> ---
> I originally added this under GCC_UFS_PHY_PHY_AUX_CLK since that's
> what's in the downstream DTS. I was getting errors about
> GCC_UFS_PHY_AXI_CLK being stuck at off so I moved it there.
>
> Also I don't have access to any documentation for this board so I'm
> hoping that someone with docs access can verify that this is the
> appropriate place to put this.
>
> drivers/clk/qcom/gcc-sc8280xp.c | 27 ++++++++++++++-------------
> 1 file changed, 14 insertions(+), 13 deletions(-)
>
> diff --git a/drivers/clk/qcom/gcc-sc8280xp.c b/drivers/clk/qcom/gcc-sc8280xp.c
> index 4b894442fdf5..4639b50da418 100644
> --- a/drivers/clk/qcom/gcc-sc8280xp.c
> +++ b/drivers/clk/qcom/gcc-sc8280xp.c
> @@ -5685,6 +5685,19 @@ static struct clk_branch gcc_ufs_phy_ahb_clk = {
> },
> };
>
> +static struct clk_branch gcc_ufs_ref_clkref_clk = {
> + .halt_reg = 0x8c058,
> + .halt_check = BRANCH_HALT,
> + .clkr = {
> + .enable_reg = 0x8c058,
> + .enable_mask = BIT(0),
> + .hw.init = &(const struct clk_init_data) {
> + .name = "gcc_ufs_ref_clkref_clk",
> + .ops = &clk_branch2_ops,
> + },
> + },
> +};
> +
> static struct clk_branch gcc_ufs_phy_axi_clk = {
> .halt_reg = 0x77010,
> .halt_check = BRANCH_HALT_VOTED,
> @@ -5696,6 +5709,7 @@ static struct clk_branch gcc_ufs_phy_axi_clk = {
> .hw.init = &(const struct clk_init_data) {
> .name = "gcc_ufs_phy_axi_clk",
> .parent_hws = (const struct clk_hw*[]){
> + &gcc_ufs_ref_clkref_clk.clkr.hw,
gcc_ufs_ref_clkref_clk isn't the parent of gcc_ufs_phy_axi_clk.
But I presume that if this works, then you're just enabling the ufs
clkref clock, indirectly. Seems reasonable that you should be specifying
gcc_ufs_ref_clkref_clk as "ref_clk" instead.
Could you please give that a go?
Regards,
Bjorn
> &gcc_ufs_phy_axi_clk_src.clkr.hw,
> },
> .num_parents = 1,
> @@ -5899,19 +5913,6 @@ static struct clk_branch gcc_ufs_phy_unipro_core_hw_ctl_clk = {
> },
> };
>
> -static struct clk_branch gcc_ufs_ref_clkref_clk = {
> - .halt_reg = 0x8c058,
> - .halt_check = BRANCH_HALT,
> - .clkr = {
> - .enable_reg = 0x8c058,
> - .enable_mask = BIT(0),
> - .hw.init = &(const struct clk_init_data) {
> - .name = "gcc_ufs_ref_clkref_clk",
> - .ops = &clk_branch2_ops,
> - },
> - },
> -};
> -
> static struct clk_branch gcc_usb2_hs0_clkref_clk = {
> .halt_reg = 0x8c044,
> .halt_check = BRANCH_HALT,
> --
> 2.36.1
>
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH] clk: qcom: sc8280xp: add parent to gcc_ufs_phy_axi_clk for sa8540p
2022-07-16 14:54 ` Bjorn Andersson
@ 2022-07-19 18:49 ` Brian Masney
0 siblings, 0 replies; 8+ messages in thread
From: Brian Masney @ 2022-07-19 18:49 UTC (permalink / raw)
To: Bjorn Andersson
Cc: linux-arm-msm, agross, mturquette, sboyd, linux-clk,
linux-kernel, ahalaney, echanude
On Sat, Jul 16, 2022 at 09:54:43AM -0500, Bjorn Andersson wrote:
> gcc_ufs_ref_clkref_clk isn't the parent of gcc_ufs_phy_axi_clk.
>
> But I presume that if this works, then you're just enabling the ufs
> clkref clock, indirectly. Seems reasonable that you should be specifying
> gcc_ufs_ref_clkref_clk as "ref_clk" instead.
>
> Could you please give that a go?
Hey Bjorn,
I assume you mean ref_aux on the phy with this patch:
--- a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
@@ -1464,7 +1464,7 @@ ufs_mem_phy: phy@1d87000 {
clock-names = "ref",
"ref_aux";
clocks = <&rpmhcc RPMH_CXO_CLK>,
- <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
+ <&gcc GCC_UFS_REF_CLKREF_CLK>;
resets = <&ufs_mem_hc 0>;
reset-names = "ufsphy";
This works on the sa8540p.
I tried changing ref_clk on the ufs host controller from
<&rpmhcc RPMH_CXO_CLK> to the new value and the board resets.
Brian
^ permalink raw reply [flat|nested] 8+ messages in thread