[PATCH v3 00/19] Enable Qualcomm QCS 404 HS/SS USB

[PATCH v3 00/19] Enable Qualcomm QCS 404 HS/SS USB

[Bryan O'Donoghue]

V1:
This series enables the Primary and Secondary USB controllers on the
QCS404, associated PHYs, role-switching and DTS descriptions.

The series takes in a number of patches worked on by a number of people
over the past few years from downstream, through to previous upstream
submissions for both of these interfaces. Additional work has been done to
enable USB role-switching.

1. USB SS
   - extcon has been dropped in favour of gpio-usb-conn as discussed and
     agreed previously by Jorge, Bjorn, Stephen Boyd and Jack Pham [1].

   - Regulator API has been updated following suggestions from Bjorn.
   
   - Sanitzation of the DT compatible name - dropped "snps" entirely
     from the name - it made almost no sense to me and doesn't appear
     consistent with similar naming conventions for Snopsys based IP.

2. USB HS
   - Regulator API changes here.
   - Dropped "snps" from the namespace for similar reasons as above.
   - Dropped "28nm" from the namespace, looked superfluous.
   - Changed "High-Speed" to "Hi-Speed".
   - [2]

3. DWC3 Role switching
   - At the time usb-gpio-conn was discussed it was mentioned that
     role-switching was absent from the DWC3 driver.
   - John Stultz has some patches in-flight for that, that I've included in
     this series for completeness.
   - Adds my SoB to relevant patches.
   - Drops gerrit ChangeId.

4. DWC3 usb-gpio-conn
   Needs to be a child node of the DWC3 driver so some code and DT binding
   is required for that.

5. QCOM-DWC3
   Since we are role-switching with an external PMIC supplying VBUS we want
   to skip past toggling VBUS from QCOM-DWC3 controlled registers, so a
   patch is added to the qcom-dwc3 driver to do that.

References:

1: USB SS PHY for Qualcomm's QCS404
https://lwn.net/ml/devicetree/20190207111734.24171-1-jorge.ramirez-ortiz@linaro.org/

2: Add Synopsys High-Speed USB PHY driver for Qualcomm SoCs
https://lore.kernel.org/linux-arm-msm/20181127100722.9993-3-shawn.guo@linaro.org/

https://www.spinics.net/lists/linux-usb/msg190003.html

V2:
- Fixes yaml error - Rob's YAML robot
- Exclusive control of reset in PHY drivers - Philipp Zabel

V3:
- Fixes typo generating YAML warning - Rob's YAML robot

Bjorn Andersson (1):
  arm64: dts: qcom: qcs404: Add USB devices and PHYs

Bryan O'Donoghue (10):
  dt-bindings: usb: dwc3: Add a gpio-usb-connector description
  usb: dwc3: qcom: Override VBUS when using gpio_usb_connector
  usb: dwc3: Add support for usb-conn-gpio connectors
  arm64: dts: qcom: qcs404-evb: Define VBUS detect pin
  arm64: dts: qcom: qcs404-evb: Define VBUS boost pin
  arm64: dts: qcom: qcs404-evb: Define USB ID pin
  arm64: dts: qcom: qcs404-evb: Describe external VBUS regulator
  arm64: dts: qcom: qcs404-evb: Raise vreg_l12_3p3 minimum voltage
  arm64: dts: qcom: qcs404-evb: Enable secondary USB controller
  arm64: dts: qcom: qcs404-evb: Enable primary USB controller

John Stultz (2):
  dt-bindings: usb: generic: Add role-switch-default-mode binding
  usb: dwc3: Add support for role-switch-default-mode binding

Jorge Ramirez-Ortiz (3):
  dt-bindings: phy: remove qcom-dwc3-usb-phy
  dt-bindings: Add Qualcomm USB SuperSpeed PHY bindings
  phy: qualcomm: usb: Add SuperSpeed PHY driver

Shawn Guo (1):
  phy: qualcomm: Add Synopsys Hi-Speed USB PHY driver

Sriharsha Allenki (1):
  dt-bindings: phy: Add Qualcomm Synopsys Hi-Speed USB PHY binding

Yu Chen (1):
  usb: dwc3: Registering a role switch in the DRD code.

 .../bindings/phy/intel,lgm-emmc-phy.yaml      |  56 ---
 .../bindings/phy/qcom,qcs404-usb-hs.yaml      |  77 ++++
 .../devicetree/bindings/phy/qcom,usb-ss.yaml  |  75 ++++
 .../bindings/phy/qcom-dwc3-usb-phy.txt        |  37 --
 .../devicetree/bindings/usb/dwc3.txt          |  11 +
 .../devicetree/bindings/usb/generic.txt       |   6 +
 arch/arm64/boot/dts/qcom/qcs404-evb.dtsi      |  90 +++-
 arch/arm64/boot/dts/qcom/qcs404.dtsi          | 100 +++++
 drivers/phy/qualcomm/Kconfig                  |  21 +
 drivers/phy/qualcomm/Makefile                 |   2 +
 drivers/phy/qualcomm/phy-qcom-qcs404-usb-hs.c | 415 ++++++++++++++++++
 drivers/phy/qualcomm/phy-qcom-usb-ss.c        | 246 +++++++++++
 drivers/usb/dwc3/core.h                       |   6 +
 drivers/usb/dwc3/drd.c                        | 123 +++++-
 drivers/usb/dwc3/dwc3-qcom.c                  |  17 +-
 15 files changed, 1184 insertions(+), 98 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/phy/intel,lgm-emmc-phy.yaml
 create mode 100644 Documentation/devicetree/bindings/phy/qcom,qcs404-usb-hs.yaml
 create mode 100644 Documentation/devicetree/bindings/phy/qcom,usb-ss.yaml
 delete mode 100644 Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qcs404-usb-hs.c
 create mode 100644 drivers/phy/qualcomm/phy-qcom-usb-ss.c

-- 
2.25.0

[PATCH v3 01/19] dt-bindings: phy: remove qcom-dwc3-usb-phy

[Bryan O'Donoghue]

From: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>

This binding is not used by any driver.

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Cc: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@gmail.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 .../bindings/phy/qcom-dwc3-usb-phy.txt        | 37 -------------------
 1 file changed, 37 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt

diff --git a/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt b/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt
deleted file mode 100644
index a1697c27aecd..000000000000
--- a/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt
+++ /dev/null
@@ -1,37 +0,0 @@
-Qualcomm DWC3 HS AND SS PHY CONTROLLER
---------------------------------------
-
-DWC3 PHY nodes are defined to describe on-chip Synopsis Physical layer
-controllers.  Each DWC3 PHY controller should have its own node.
-
-Required properties:
-- compatible: should contain one of the following:
-	- "qcom,dwc3-hs-usb-phy" for High Speed Synopsis PHY controller
-	- "qcom,dwc3-ss-usb-phy" for Super Speed Synopsis PHY controller
-- reg: offset and length of the DWC3 PHY controller register set
-- #phy-cells: must be zero
-- clocks: a list of phandles and clock-specifier pairs, one for each entry in
-  clock-names.
-- clock-names: Should contain "ref" for the PHY reference clock
-
-Optional clocks:
-  "xo"		External reference clock
-
-Example:
-		phy@100f8800 {
-			compatible = "qcom,dwc3-hs-usb-phy";
-			reg = <0x100f8800 0x30>;
-			clocks = <&gcc USB30_0_UTMI_CLK>;
-			clock-names = "ref";
-			#phy-cells = <0>;
-
-		};
-
-		phy@100f8830 {
-			compatible = "qcom,dwc3-ss-usb-phy";
-			reg = <0x100f8830 0x30>;
-			clocks = <&gcc USB30_0_MASTER_CLK>;
-			clock-names = "ref";
-			#phy-cells = <0>;
-
-		};
-- 
2.25.0

[PATCH v3 02/19] dt-bindings: phy: Add Qualcomm Synopsys Hi-Speed USB PHY binding

[Bryan O'Donoghue]

From: Sriharsha Allenki <sallenki@codeaurora.org>

Adds bindings for QCS404 USB PHY supporting Low-Speed, Full-Speed and
Hi-Speed USB connectivity on Qualcomm chipsets.

[bod: Converted to YAML. Changed name dropping snps, 28nm components]

Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
Signed-off-by: Anu Ramanathan <anur@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 .../bindings/phy/qcom,qcs404-usb-hs.yaml      | 77 +++++++++++++++++++
 1 file changed, 77 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/qcom,qcs404-usb-hs.yaml

diff --git a/Documentation/devicetree/bindings/phy/qcom,qcs404-usb-hs.yaml b/Documentation/devicetree/bindings/phy/qcom,qcs404-usb-hs.yaml
new file mode 100644
index 000000000000..d71beb822ae2
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom,qcs404-usb-hs.yaml
@@ -0,0 +1,77 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/phy/qcom,qcs404-usb-hs.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Qualcomm Synopsys QCS-404 High-Speed PHY
+
+maintainers:
+  - Bryan O'Donoghue <bryan.odonoghue@linaro.org>
+
+description: |
+  Qualcomm QCS-404 Low-Speed, Full-Speed, Hi-Speed USB PHY
+
+properties:
+  compatible:
+    enum:
+      - qcom,qcs404-usb-hsphy
+
+  reg:
+    maxItems: 1
+    description: USB PHY base address and length of the register map.
+
+  "#phy-cells":
+    const: 0
+    description: Should be 0. See phy/phy-bindings.txt for details.
+
+  clocks:
+    minItems: 3
+    maxItems: 3
+    description: phandles to rpmcc ref clock, PHY AHB clock, rentention clock.
+
+  clock-names:
+    items:
+      - const: ref
+      - const: phy
+      - const: sleep
+
+  resets:
+    items:
+      - description: PHY core reset
+      - description: POR reset
+
+  reset-names:
+    items:
+      - const: phy
+      - const: por
+
+  vdd-supply:
+    maxItems: 1
+    description: phandle to the regulator VDD supply node.
+
+  vdda1p8-supply:
+    maxItems: 1
+    description: phandle to the regulator 1.8V supply node.
+
+  vdda3p3-supply:
+    maxItems: 1
+    description: phandle to the regulator 3.3V supply node.
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,gcc-qcs404.h>
+    #include <dt-bindings/clock/qcom,rpmcc.h>
+    usb2_phy_prim: phy@7a000 {
+        compatible = "qcom,qcs404-usb-hsphy";
+        reg = <0x0007a000 0x200>;
+        #phy-cells = <0>;
+        clocks = <&rpmcc RPM_SMD_LN_BB_CLK>,
+                 <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
+                 <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+        clock-names = "ref", "phy", "sleep";
+        resets = <&gcc GCC_USB_HS_PHY_CFG_AHB_BCR>,
+                 <&gcc GCC_USB2A_PHY_BCR>;
+        reset-names = "phy", "por";
+    };
+...
-- 
2.25.0

[PATCH v3 03/19] phy: qualcomm: Add Synopsys Hi-Speed USB PHY driver

[Bryan O'Donoghue]

From: Shawn Guo <shawn.guo@linaro.org>

Adds Qualcomm QCS404 Hi-Speed USB PHY driver support. This PHY is usually
is usually paired with Synopsys DWC3 USB controllers on Qualcomm SoCs.

[bod: Updated qcom_snps_hsphy_set_mode to match new method signature
      Added disjunct on mode > 0
      Removed regulator_set_voltage() in favour of setting floor in dts
      Removed 'snps' and '28nm' from driver name]

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 drivers/phy/qualcomm/Kconfig                  |  10 +
 drivers/phy/qualcomm/Makefile                 |   1 +
 drivers/phy/qualcomm/phy-qcom-qcs404-usb-hs.c | 415 ++++++++++++++++++
 3 files changed, 426 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qcs404-usb-hs.c

diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig
index e46824da29f6..cc3f2bb01ad1 100644
--- a/drivers/phy/qualcomm/Kconfig
+++ b/drivers/phy/qualcomm/Kconfig
@@ -91,3 +91,13 @@ config PHY_QCOM_USB_HSIC
 	select GENERIC_PHY
 	help
 	  Support for the USB HSIC ULPI compliant PHY on QCOM chipsets.
+
+config PHY_QCOM_QCS404_USB_HS
+	tristate "Qualcomm QCS404 Hi-Speed USB PHY driver"
+	depends on ARCH_QCOM || COMPILE_TEST
+	depends on EXTCON || !EXTCON # if EXTCON=m, this cannot be built-in
+	select GENERIC_PHY
+	help
+	  Enable this to support the Qualcomm QCS404 USB Hi-Speed PHY driver.
+	  This driver supports the Hi-Speed PHY which is usually paired with
+	  either the ChipIdea or Synopsys DWC3 USB IPs on MSM SOCs.
diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile
index 283251d6a5d9..a4a3b21240fa 100644
--- a/drivers/phy/qualcomm/Makefile
+++ b/drivers/phy/qualcomm/Makefile
@@ -10,3 +10,4 @@ obj-$(CONFIG_PHY_QCOM_UFS_14NM)		+= phy-qcom-ufs-qmp-14nm.o
 obj-$(CONFIG_PHY_QCOM_UFS_20NM)		+= phy-qcom-ufs-qmp-20nm.o
 obj-$(CONFIG_PHY_QCOM_USB_HS) 		+= phy-qcom-usb-hs.o
 obj-$(CONFIG_PHY_QCOM_USB_HSIC) 	+= phy-qcom-usb-hsic.o
+obj-$(CONFIG_PHY_QCOM_QCS404_USB_HS)	+= phy-qcom-qcs404-usb-hs.o
diff --git a/drivers/phy/qualcomm/phy-qcom-qcs404-usb-hs.c b/drivers/phy/qualcomm/phy-qcom-qcs404-usb-hs.c
new file mode 100644
index 000000000000..0ea7c32941dd
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-qcs404-usb-hs.c
@@ -0,0 +1,415 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2009-2018, Linux Foundation. All rights reserved.
+ * Copyright (c) 2018-2020, Linaro Limited
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_graph.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+
+/* PHY register and bit definitions */
+#define PHY_CTRL_COMMON0		0x078
+#define SIDDQ				BIT(2)
+#define PHY_IRQ_CMD			0x0d0
+#define PHY_INTR_MASK0			0x0d4
+#define PHY_INTR_CLEAR0			0x0dc
+#define DPDM_MASK			0x1e
+#define DP_1_0				BIT(4)
+#define DP_0_1				BIT(3)
+#define DM_1_0				BIT(2)
+#define DM_0_1				BIT(1)
+
+enum hsphy_voltage {
+	VOL_NONE,
+	VOL_MIN,
+	VOL_MAX,
+	VOL_NUM,
+};
+
+enum hsphy_vreg {
+	VDD,
+	VDDA_1P8,
+	VDDA_3P3,
+	VREG_NUM,
+};
+
+struct hsphy_init_seq {
+	int offset;
+	int val;
+	int delay;
+};
+
+struct hsphy_data {
+	const struct hsphy_init_seq *init_seq;
+	unsigned int init_seq_num;
+};
+
+struct hsphy_priv {
+	void __iomem *base;
+	struct clk_bulk_data *clks;
+	int num_clks;
+	struct reset_control *phy_reset;
+	struct reset_control *por_reset;
+	struct regulator_bulk_data vregs[VREG_NUM];
+	const struct hsphy_data *data;
+	enum phy_mode mode;
+};
+
+static int qcom_snps_hsphy_set_mode(struct phy *phy, enum phy_mode mode,
+				    int submode)
+{
+	struct hsphy_priv *priv = phy_get_drvdata(phy);
+
+	priv->mode = PHY_MODE_INVALID;
+
+	if (mode > 0)
+		priv->mode = mode;
+
+	return 0;
+}
+
+static void qcom_snps_hsphy_enable_hv_interrupts(struct hsphy_priv *priv)
+{
+	u32 val;
+
+	/* Clear any existing interrupts before enabling the interrupts */
+	val = readb(priv->base + PHY_INTR_CLEAR0);
+	val |= DPDM_MASK;
+	writeb(val, priv->base + PHY_INTR_CLEAR0);
+
+	writeb(0x0, priv->base + PHY_IRQ_CMD);
+	usleep_range(200, 220);
+	writeb(0x1, priv->base + PHY_IRQ_CMD);
+
+	/* Make sure the interrupts are cleared */
+	usleep_range(200, 220);
+
+	val = readb(priv->base + PHY_INTR_MASK0);
+	switch (priv->mode) {
+	case PHY_MODE_USB_HOST_HS:
+	case PHY_MODE_USB_HOST_FS:
+	case PHY_MODE_USB_DEVICE_HS:
+	case PHY_MODE_USB_DEVICE_FS:
+		val |= DP_1_0 | DM_0_1;
+		break;
+	case PHY_MODE_USB_HOST_LS:
+	case PHY_MODE_USB_DEVICE_LS:
+		val |= DP_0_1 | DM_1_0;
+		break;
+	default:
+		/* No device connected */
+		val |= DP_0_1 | DM_0_1;
+		break;
+	}
+	writeb(val, priv->base + PHY_INTR_MASK0);
+}
+
+static void qcom_snps_hsphy_disable_hv_interrupts(struct hsphy_priv *priv)
+{
+	u32 val;
+
+	val = readb(priv->base + PHY_INTR_MASK0);
+	val &= ~DPDM_MASK;
+	writeb(val, priv->base + PHY_INTR_MASK0);
+
+	/* Clear any pending interrupts */
+	val = readb(priv->base + PHY_INTR_CLEAR0);
+	val |= DPDM_MASK;
+	writeb(val, priv->base + PHY_INTR_CLEAR0);
+
+	writeb(0x0, priv->base + PHY_IRQ_CMD);
+	usleep_range(200, 220);
+
+	writeb(0x1, priv->base + PHY_IRQ_CMD);
+	usleep_range(200, 220);
+}
+
+static void qcom_snps_hsphy_enter_retention(struct hsphy_priv *priv)
+{
+	u32 val;
+
+	val = readb(priv->base + PHY_CTRL_COMMON0);
+	val |= SIDDQ;
+	writeb(val, priv->base + PHY_CTRL_COMMON0);
+}
+
+static void qcom_snps_hsphy_exit_retention(struct hsphy_priv *priv)
+{
+	u32 val;
+
+	val = readb(priv->base + PHY_CTRL_COMMON0);
+	val &= ~SIDDQ;
+	writeb(val, priv->base + PHY_CTRL_COMMON0);
+}
+
+static int qcom_snps_hsphy_power_on(struct phy *phy)
+{
+	struct hsphy_priv *priv = phy_get_drvdata(phy);
+	int ret;
+
+	ret = regulator_bulk_enable(VREG_NUM, priv->vregs);
+	if (ret)
+		return ret;
+	ret = clk_bulk_prepare_enable(priv->num_clks, priv->clks);
+	if (ret)
+		goto err_disable_regulator;
+	qcom_snps_hsphy_disable_hv_interrupts(priv);
+	qcom_snps_hsphy_exit_retention(priv);
+
+	return 0;
+
+err_disable_regulator:
+	regulator_bulk_disable(VREG_NUM, priv->vregs);
+
+	return ret;
+}
+
+static int qcom_snps_hsphy_power_off(struct phy *phy)
+{
+	struct hsphy_priv *priv = phy_get_drvdata(phy);
+
+	qcom_snps_hsphy_enter_retention(priv);
+	qcom_snps_hsphy_enable_hv_interrupts(priv);
+	clk_bulk_disable_unprepare(priv->num_clks, priv->clks);
+	regulator_bulk_disable(VREG_NUM, priv->vregs);
+
+	return 0;
+}
+
+static int qcom_snps_hsphy_reset(struct hsphy_priv *priv)
+{
+	int ret;
+
+	ret = reset_control_assert(priv->phy_reset);
+	if (ret)
+		return ret;
+
+	usleep_range(10, 15);
+
+	ret = reset_control_deassert(priv->phy_reset);
+	if (ret)
+		return ret;
+
+	usleep_range(80, 100);
+
+	return 0;
+}
+
+static void qcom_snps_hsphy_init_sequence(struct hsphy_priv *priv)
+{
+	const struct hsphy_data *data = priv->data;
+	const struct hsphy_init_seq *seq;
+	int i;
+
+	/* Device match data is optional. */
+	if (!data)
+		return;
+
+	seq = data->init_seq;
+
+	for (i = 0; i < data->init_seq_num; i++, seq++) {
+		writeb(seq->val, priv->base + seq->offset);
+		if (seq->delay)
+			usleep_range(seq->delay, seq->delay + 10);
+	}
+}
+
+static int qcom_snps_hsphy_por_reset(struct hsphy_priv *priv)
+{
+	int ret;
+
+	ret = reset_control_assert(priv->por_reset);
+	if (ret)
+		return ret;
+
+	/*
+	 * The Femto PHY is POR reset in the following scenarios.
+	 *
+	 * 1. After overriding the parameter registers.
+	 * 2. Low power mode exit from PHY retention.
+	 *
+	 * Ensure that SIDDQ is cleared before bringing the PHY
+	 * out of reset.
+	 */
+	qcom_snps_hsphy_exit_retention(priv);
+
+	/*
+	 * As per databook, 10 usec delay is required between
+	 * PHY POR assert and de-assert.
+	 */
+	usleep_range(10, 20);
+	ret = reset_control_deassert(priv->por_reset);
+	if (ret)
+		return ret;
+
+	/*
+	 * As per databook, it takes 75 usec for PHY to stabilize
+	 * after the reset.
+	 */
+	usleep_range(80, 100);
+
+	return 0;
+}
+
+static int qcom_snps_hsphy_init(struct phy *phy)
+{
+	struct hsphy_priv *priv = phy_get_drvdata(phy);
+	int ret;
+
+	ret = qcom_snps_hsphy_reset(priv);
+	if (ret)
+		return ret;
+
+	qcom_snps_hsphy_init_sequence(priv);
+
+	ret = qcom_snps_hsphy_por_reset(priv);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static const struct phy_ops qcom_snps_hsphy_ops = {
+	.init = qcom_snps_hsphy_init,
+	.power_on = qcom_snps_hsphy_power_on,
+	.power_off = qcom_snps_hsphy_power_off,
+	.set_mode = qcom_snps_hsphy_set_mode,
+	.owner = THIS_MODULE,
+};
+
+static const char * const qcom_snps_hsphy_clks[] = {
+	"ref",
+	"phy",
+	"sleep",
+};
+
+static int qcom_snps_hsphy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct phy_provider *provider;
+	struct hsphy_priv *priv;
+	struct phy *phy;
+	int ret;
+	int i;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(priv->base))
+		return PTR_ERR(priv->base);
+
+	priv->num_clks = ARRAY_SIZE(qcom_snps_hsphy_clks);
+	priv->clks = devm_kcalloc(dev, priv->num_clks, sizeof(*priv->clks),
+				  GFP_KERNEL);
+	if (!priv->clks)
+		return -ENOMEM;
+
+	for (i = 0; i < priv->num_clks; i++)
+		priv->clks[i].id = qcom_snps_hsphy_clks[i];
+
+	ret = devm_clk_bulk_get(dev, priv->num_clks, priv->clks);
+	if (ret)
+		return ret;
+
+	priv->phy_reset = devm_reset_control_get_exclusive(dev, "phy");
+	if (IS_ERR(priv->phy_reset))
+		return PTR_ERR(priv->phy_reset);
+
+	priv->por_reset = devm_reset_control_get_exclusive(dev, "por");
+	if (IS_ERR(priv->por_reset))
+		return PTR_ERR(priv->por_reset);
+
+	priv->vregs[VDD].supply = "vdd";
+	priv->vregs[VDDA_1P8].supply = "vdda1p8";
+	priv->vregs[VDDA_3P3].supply = "vdda3p3";
+
+	ret = devm_regulator_bulk_get(dev, VREG_NUM, priv->vregs);
+	if (ret)
+		return ret;
+
+	/* Get device match data */
+	priv->data = device_get_match_data(dev);
+
+	phy = devm_phy_create(dev, dev->of_node, &qcom_snps_hsphy_ops);
+	if (IS_ERR(phy))
+		return PTR_ERR(phy);
+
+	phy_set_drvdata(phy, priv);
+
+	provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	if (IS_ERR(provider))
+		return PTR_ERR(provider);
+
+	ret = regulator_set_load(priv->vregs[VDDA_1P8].consumer, 19000);
+	if (ret < 0)
+		return ret;
+
+	ret = regulator_set_load(priv->vregs[VDDA_3P3].consumer, 16000);
+	if (ret < 0)
+		goto unset_1p8_load;
+
+	return 0;
+
+unset_1p8_load:
+	regulator_set_load(priv->vregs[VDDA_1P8].consumer, 0);
+
+	return ret;
+}
+
+/*
+ * The macro is used to define an initialization sequence.  Each tuple
+ * is meant to program 'value' into phy register at 'offset' with 'delay'
+ * in us followed.
+ */
+#define HSPHY_INIT_CFG(o, v, d)	{ .offset = o, .val = v, .delay = d, }
+
+static const struct hsphy_init_seq init_seq_qcs404[] = {
+	HSPHY_INIT_CFG(0xc0, 0x01, 0),
+	HSPHY_INIT_CFG(0xe8, 0x0d, 0),
+	HSPHY_INIT_CFG(0x74, 0x12, 0),
+	HSPHY_INIT_CFG(0x98, 0x63, 0),
+	HSPHY_INIT_CFG(0x9c, 0x03, 0),
+	HSPHY_INIT_CFG(0xa0, 0x1d, 0),
+	HSPHY_INIT_CFG(0xa4, 0x03, 0),
+	HSPHY_INIT_CFG(0x8c, 0x23, 0),
+	HSPHY_INIT_CFG(0x78, 0x08, 0),
+	HSPHY_INIT_CFG(0x7c, 0xdc, 0),
+	HSPHY_INIT_CFG(0x90, 0xe0, 20),
+	HSPHY_INIT_CFG(0x74, 0x10, 0),
+	HSPHY_INIT_CFG(0x90, 0x60, 0),
+};
+
+static const struct hsphy_data hsphy_data_qcs404 = {
+	.init_seq = init_seq_qcs404,
+	.init_seq_num = ARRAY_SIZE(init_seq_qcs404),
+};
+
+static const struct of_device_id qcom_snps_hsphy_match[] = {
+	{ .compatible = "qcom,qcs404-usb-hsphy", .data = &hsphy_data_qcs404, },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, qcom_snps_hsphy_match);
+
+static struct platform_driver qcom_snps_hsphy_driver = {
+	.probe = qcom_snps_hsphy_probe,
+	.driver	= {
+		.name = "qcom-qcs404-usb-hsphy",
+		.of_match_table = qcom_snps_hsphy_match,
+	},
+};
+module_platform_driver(qcom_snps_hsphy_driver);
+
+MODULE_DESCRIPTION("Qualcomm QCS404 Hi-Speed USB PHY driver");
+MODULE_LICENSE("GPL v2");
-- 
2.25.0

[PATCH v3 04/19] dt-bindings: Add Qualcomm USB SuperSpeed PHY bindings

[Bryan O'Donoghue]

From: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>

Binding description for Qualcomm's Synopsys 1.0.0 SuperSpeed phy
controller embedded in QCS404.

Based on Sriharsha Allenki's <sallenki@codeaurora.org> original
definitions.

[bod: converted to yaml format]

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Cc: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 .../bindings/phy/intel,lgm-emmc-phy.yaml      | 56 --------------
 .../devicetree/bindings/phy/qcom,usb-ss.yaml  | 75 +++++++++++++++++++
 2 files changed, 75 insertions(+), 56 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/phy/intel,lgm-emmc-phy.yaml
 create mode 100644 Documentation/devicetree/bindings/phy/qcom,usb-ss.yaml

diff --git a/Documentation/devicetree/bindings/phy/intel,lgm-emmc-phy.yaml b/Documentation/devicetree/bindings/phy/intel,lgm-emmc-phy.yaml
deleted file mode 100644
index ff7959c21af0..000000000000
--- a/Documentation/devicetree/bindings/phy/intel,lgm-emmc-phy.yaml
+++ /dev/null
@@ -1,56 +0,0 @@
-# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
-%YAML 1.2
----
-$id: http://devicetree.org/schemas/phy/intel,lgm-emmc-phy.yaml#
-$schema: http://devicetree.org/meta-schemas/core.yaml#
-
-title: Intel Lightning Mountain(LGM) eMMC PHY Device Tree Bindings
-
-maintainers:
-  - Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
-
-description: |+
-  Bindings for eMMC PHY on Intel's Lightning Mountain SoC, syscon
-  node is used to reference the base address of eMMC phy registers.
-
-  The eMMC PHY node should be the child of a syscon node with the
-  required property:
-
-  - compatible:         Should be one of the following:
-                        "intel,lgm-syscon", "syscon"
-  - reg:
-      maxItems: 1
-
-properties:
-  compatible:
-      const: intel,lgm-emmc-phy
-
-  "#phy-cells":
-    const: 0
-
-  reg:
-    maxItems: 1
-
-  clocks:
-    maxItems: 1
-
-required:
-  - "#phy-cells"
-  - compatible
-  - reg
-  - clocks
-
-examples:
-  - |
-    sysconf: chiptop@e0200000 {
-      compatible = "intel,lgm-syscon", "syscon";
-      reg = <0xe0200000 0x100>;
-
-      emmc-phy: emmc-phy@a8 {
-        compatible = "intel,lgm-emmc-phy";
-        reg = <0x00a8 0x10>;
-        clocks = <&emmc>;
-        #phy-cells = <0>;
-      };
-    };
-...
diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-ss.yaml b/Documentation/devicetree/bindings/phy/qcom,usb-ss.yaml
new file mode 100644
index 000000000000..3325b2f2e6a8
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom,usb-ss.yaml
@@ -0,0 +1,75 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/phy/qcom,usb-ss.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Qualcomm Synopsys 1.0.0 SuperSpeed USB PHY
+
+maintainers:
+  - Bryan O'Donoghue <bryan.odonoghue@linaro.org>
+
+description: |
+  Qualcomm Synopsys 1.0.0 SuperSpeed USB PHY
+
+properties:
+  compatible:
+    enum:
+      - qcom,usb-ssphy
+
+  reg:
+    maxItems: 1
+    description: USB PHY base address and length of the register map.
+
+  "#phy-cells":
+    const: 0
+    description: Should be 0. See phy/phy-bindings.txt for details.
+
+  clocks:
+    maxItems: 3
+    minItems: 3
+    description: phandles for rpmcc clock, PHY AHB clock, SuperSpeed pipe clock.
+
+  clock-names:
+    items:
+      - const: ref
+      - const: phy
+      - const: pipe
+
+  vdd-supply:
+    maxItems: 1
+    description: phandle to the regulator VDD supply node.
+
+  vdda1p8-supply:
+    maxItems: 1
+    description: phandle to the regulator 1.8V supply node.
+
+  resets:
+    items:
+      - description: COM reset
+      - description: PHY reset line
+
+  reset-names:
+    items:
+      - const: com
+      - const: phy
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,gcc-qcs404.h>
+    #include <dt-bindings/clock/qcom,rpmcc.h>
+    usb3_phy: usb3-phy@78000 {
+        compatible = "qcom,usb-ssphy";
+        reg = <0x78000 0x400>;
+        #phy-cells = <0>;
+        clocks = <&rpmcc RPM_SMD_LN_BB_CLK>,
+                 <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
+                 <&gcc GCC_USB3_PHY_PIPE_CLK>;
+        clock-names = "ref", "phy", "pipe";
+        resets = <&gcc GCC_USB3_PHY_BCR>,
+                 <&gcc GCC_USB3PHY_PHY_BCR>;
+        reset-names = "com", "phy";
+        vdd-supply = <&vreg_l3_1p05>;
+        vdda1p8-supply = <&vreg_l5_1p8>;
+    };
+...
-- 
2.25.0

[PATCH v3 05/19] phy: qualcomm: usb: Add SuperSpeed PHY driver

[Bryan O'Donoghue]

From: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>

Controls Qualcomm's SS phy 1.0.0 implemented in the QCS404 and some
other Qualcomm platforms.

Based on Sriharsha Allenki's <sallenki@codeaurora.org> original code.

[bod: Removed dependency on extcon.
      Switched to gpio-usb-conn to handle VBUS On/Off
      Switched to usb-role-switch to bind gpio-usb-conn to DWC3]
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Cc: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@gmail.com>
Cc: Sriharsha Allenki's <sallenki@codeaurora.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 drivers/phy/qualcomm/Kconfig           |  11 ++
 drivers/phy/qualcomm/Makefile          |   1 +
 drivers/phy/qualcomm/phy-qcom-usb-ss.c | 246 +++++++++++++++++++++++++
 3 files changed, 258 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-usb-ss.c

diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig
index cc3f2bb01ad1..d95602ec6515 100644
--- a/drivers/phy/qualcomm/Kconfig
+++ b/drivers/phy/qualcomm/Kconfig
@@ -101,3 +101,14 @@ config PHY_QCOM_QCS404_USB_HS
 	  Enable this to support the Qualcomm QCS404 USB Hi-Speed PHY driver.
 	  This driver supports the Hi-Speed PHY which is usually paired with
 	  either the ChipIdea or Synopsys DWC3 USB IPs on MSM SOCs.
+
+config PHY_QCOM_USB_SS
+	tristate "Qualcomm USB SS PHY driver"
+	depends on ARCH_QCOM || COMPILE_TEST
+	depends on EXTCON || !EXTCON # if EXTCON=m, this cannot be built-in
+	select GENERIC_PHY
+	help
+	  Enable this to support the Super-Speed USB transceiver on Qualcomm
+	  chips. This driver supports the PHY which uses the QSCRATCH-based
+	  register set for its control sequences, normally paired with newer
+	  DWC3-based Super-Speed controllers on Qualcomm SoCs.
diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile
index a4a3b21240fa..e8c7137cdbed 100644
--- a/drivers/phy/qualcomm/Makefile
+++ b/drivers/phy/qualcomm/Makefile
@@ -11,3 +11,4 @@ obj-$(CONFIG_PHY_QCOM_UFS_20NM)		+= phy-qcom-ufs-qmp-20nm.o
 obj-$(CONFIG_PHY_QCOM_USB_HS) 		+= phy-qcom-usb-hs.o
 obj-$(CONFIG_PHY_QCOM_USB_HSIC) 	+= phy-qcom-usb-hsic.o
 obj-$(CONFIG_PHY_QCOM_QCS404_USB_HS)	+= phy-qcom-qcs404-usb-hs.o
+obj-$(CONFIG_PHY_QCOM_USB_SS)		+= phy-qcom-usb-ss.o
diff --git a/drivers/phy/qualcomm/phy-qcom-usb-ss.c b/drivers/phy/qualcomm/phy-qcom-usb-ss.c
new file mode 100644
index 000000000000..bc4951ddcc09
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-usb-ss.c
@@ -0,0 +1,246 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2012-2014,2017 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2018-2020, Linaro Limited
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+
+#define PHY_CTRL0			0x6C
+#define PHY_CTRL1			0x70
+#define PHY_CTRL2			0x74
+#define PHY_CTRL4			0x7C
+
+/* PHY_CTRL bits */
+#define REF_PHY_EN			BIT(0)
+#define LANE0_PWR_ON			BIT(2)
+#define SWI_PCS_CLK_SEL			BIT(4)
+#define TST_PWR_DOWN			BIT(4)
+#define PHY_RESET			BIT(7)
+
+#define NUM_BULK_CLKS	3
+#define NUM_BULK_REGS	2
+
+struct ssphy_priv {
+	void __iomem *base;
+	struct device *dev;
+	struct reset_control *reset_com;
+	struct reset_control *reset_phy;
+	struct regulator_bulk_data regs[NUM_BULK_REGS];
+	struct clk_bulk_data clks[NUM_BULK_CLKS];
+	enum phy_mode mode;
+};
+
+static inline void qcom_ssphy_updatel(void __iomem *addr, u32 mask, u32 val)
+{
+	writel((readl(addr) & ~mask) | val, addr);
+}
+
+static int qcom_ssphy_do_reset(struct ssphy_priv *priv)
+{
+	int ret;
+
+	if (!priv->reset_com) {
+		qcom_ssphy_updatel(priv->base + PHY_CTRL1, PHY_RESET,
+				   PHY_RESET);
+		usleep_range(10, 20);
+		qcom_ssphy_updatel(priv->base + PHY_CTRL1, PHY_RESET, 0);
+	} else {
+		ret = reset_control_assert(priv->reset_com);
+		if (ret) {
+			dev_err(priv->dev, "Failed to assert reset com\n");
+			return ret;
+		}
+
+		ret = reset_control_assert(priv->reset_phy);
+		if (ret) {
+			dev_err(priv->dev, "Failed to assert reset phy\n");
+			return ret;
+		}
+
+		usleep_range(10, 20);
+
+		ret = reset_control_deassert(priv->reset_com);
+		if (ret) {
+			dev_err(priv->dev, "Failed to deassert reset com\n");
+			return ret;
+		}
+
+		ret = reset_control_deassert(priv->reset_phy);
+		if (ret) {
+			dev_err(priv->dev, "Failed to deassert reset phy\n");
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static int qcom_ssphy_power_on(struct phy *phy)
+{
+	struct ssphy_priv *priv = phy_get_drvdata(phy);
+	int ret;
+
+	ret = regulator_bulk_enable(NUM_BULK_REGS, priv->regs);
+	if (ret)
+		return ret;
+
+	ret = clk_bulk_prepare_enable(NUM_BULK_CLKS, priv->clks);
+	if (ret)
+		goto err_disable_regulator;
+
+	ret = qcom_ssphy_do_reset(priv);
+	if (ret)
+		goto err_disable_clock;
+
+	writeb(SWI_PCS_CLK_SEL, priv->base + PHY_CTRL0);
+	qcom_ssphy_updatel(priv->base + PHY_CTRL4, LANE0_PWR_ON, LANE0_PWR_ON);
+	qcom_ssphy_updatel(priv->base + PHY_CTRL2, REF_PHY_EN, REF_PHY_EN);
+	qcom_ssphy_updatel(priv->base + PHY_CTRL4, TST_PWR_DOWN, 0);
+
+	return 0;
+err_disable_clock:
+	clk_bulk_disable_unprepare(NUM_BULK_CLKS, priv->clks);
+err_disable_regulator:
+	regulator_bulk_disable(NUM_BULK_REGS, priv->regs);
+
+	return ret;
+}
+
+static int qcom_ssphy_power_off(struct phy *phy)
+{
+	struct ssphy_priv *priv = phy_get_drvdata(phy);
+
+	qcom_ssphy_updatel(priv->base + PHY_CTRL4, LANE0_PWR_ON, 0);
+	qcom_ssphy_updatel(priv->base + PHY_CTRL2, REF_PHY_EN, 0);
+	qcom_ssphy_updatel(priv->base + PHY_CTRL4, TST_PWR_DOWN, TST_PWR_DOWN);
+
+	clk_bulk_disable_unprepare(NUM_BULK_CLKS, priv->clks);
+	regulator_bulk_disable(NUM_BULK_REGS, priv->regs);
+
+	return 0;
+}
+
+static int qcom_ssphy_init_clock(struct ssphy_priv *priv)
+{
+	priv->clks[0].id = "ref";
+	priv->clks[1].id = "phy";
+	priv->clks[2].id = "pipe";
+
+	return devm_clk_bulk_get(priv->dev, NUM_BULK_CLKS, priv->clks);
+}
+
+static int qcom_ssphy_init_regulator(struct ssphy_priv *priv)
+{
+	int ret;
+
+	priv->regs[0].supply = "vdd";
+	priv->regs[1].supply = "vdda1p8";
+	ret = devm_regulator_bulk_get(priv->dev, NUM_BULK_REGS, priv->regs);
+	if (ret) {
+		if (ret != -EPROBE_DEFER)
+			dev_err(priv->dev, "Failed to get regulators\n");
+		return ret;
+	}
+
+	return ret;
+}
+
+static int qcom_ssphy_init_reset(struct ssphy_priv *priv)
+{
+	priv->reset_com = devm_reset_control_get_optional_exclusive(priv->dev, "com");
+	if (IS_ERR(priv->reset_com)) {
+		dev_err(priv->dev, "Failed to get reset control com\n");
+		return PTR_ERR(priv->reset_com);
+	}
+
+	if (priv->reset_com) {
+		/* if reset_com is present, reset_phy is no longer optional */
+		priv->reset_phy = devm_reset_control_get_exclusive(priv->dev, "phy");
+		if (IS_ERR(priv->reset_phy)) {
+			dev_err(priv->dev, "Failed to get reset control phy\n");
+			return PTR_ERR(priv->reset_phy);
+		}
+	}
+
+	return 0;
+}
+
+static const struct phy_ops qcom_ssphy_ops = {
+	.power_off = qcom_ssphy_power_off,
+	.power_on = qcom_ssphy_power_on,
+	.owner = THIS_MODULE,
+};
+
+static int qcom_ssphy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct phy_provider *provider;
+	struct ssphy_priv *priv;
+	struct phy *phy;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(struct ssphy_priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->dev = dev;
+	priv->mode = PHY_MODE_INVALID;
+
+	priv->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(priv->base))
+		return PTR_ERR(priv->base);
+
+	ret = qcom_ssphy_init_clock(priv);
+	if (ret)
+		return ret;
+
+	ret = qcom_ssphy_init_reset(priv);
+	if (ret)
+		return ret;
+
+	ret = qcom_ssphy_init_regulator(priv);
+	if (ret)
+		return ret;
+
+	phy = devm_phy_create(dev, dev->of_node, &qcom_ssphy_ops);
+	if (IS_ERR(phy)) {
+		dev_err(dev, "Failed to create the SS phy\n");
+		return PTR_ERR(phy);
+	}
+
+	phy_set_drvdata(phy, priv);
+
+	provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+	return PTR_ERR_OR_ZERO(provider);
+}
+
+static const struct of_device_id qcom_ssphy_match[] = {
+	{ .compatible = "qcom,usb-ssphy", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, qcom_ssphy_match);
+
+static struct platform_driver qcom_ssphy_driver = {
+	.probe		= qcom_ssphy_probe,
+	.driver = {
+		.name	= "qcom-usb-ssphy",
+		.of_match_table = qcom_ssphy_match,
+	},
+};
+module_platform_driver(qcom_ssphy_driver);
+
+MODULE_DESCRIPTION("Qualcomm SuperSpeed USB PHY driver");
+MODULE_LICENSE("GPL v2");
-- 
2.25.0

[PATCH v3 06/19] dt-bindings: usb: dwc3: Add a gpio-usb-connector description

[Bryan O'Donoghue]

A USB connector should be a child node of the USB controller
connector/usb-connector.txt. This patch adds a property
"gpio_usb_connector" which declares a connector child device. Code in the
DWC3 driver will then

- Search for "gpio_usb_controller"
- Do an of_platform_populate() if found

This will have the effect of making the declared node a child of the USB
controller and will make sure that USB role-switch events detected with the
gpio_usb_controller driver propagate into the DWC3 controller code
appropriately.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-usb@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 Documentation/devicetree/bindings/usb/dwc3.txt | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt
index 66780a47ad85..b019bd472f83 100644
--- a/Documentation/devicetree/bindings/usb/dwc3.txt
+++ b/Documentation/devicetree/bindings/usb/dwc3.txt
@@ -108,6 +108,9 @@ Optional properties:
 			When just one value, which means INCRX burst mode enabled. When
 			more than one value, which means undefined length INCR burst type
 			enabled. The values can be 1, 4, 8, 16, 32, 64, 128 and 256.
+ - gpio_usb_connector: Declares a USB connector named 'gpio_usb_connector' as a
+		       child node of the DWC3 block. Use when modelling a USB
+		       connector based on the gpio-usb-b-connector driver.
 
  - in addition all properties from usb-xhci.txt from the current directory are
    supported as well
@@ -121,4 +124,12 @@ dwc3@4a030000 {
 	interrupts = <0 92 4>
 	usb-phy = <&usb2_phy>, <&usb3,phy>;
 	snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
+	usb_con: gpio_usb_connector {
+		compatible = "gpio-usb-b-connector";
+		id-gpio = <&tlmm 116 GPIO_ACTIVE_HIGH>;
+		vbus-gpio = <&pms405_gpios 12 GPIO_ACTIVE_HIGH>;
+		vbus-supply = <&usb3_vbus_reg>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb3_id_pin>, <&usb3_vbus_pin>;
+	};
 };
-- 
2.25.0

[PATCH v3 07/19] usb: dwc3: Registering a role switch in the DRD code.

[Bryan O'Donoghue]

From: Yu Chen <chenyu56@huawei.com>

The Type-C drivers use USB role switch API to inform the
system about the negotiated data role, so registering a role
switch in the DRD code in order to support platforms with
USB Type-C connectors.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
CC: ShuFan Lee <shufan_lee@richtek.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Yu Chen <chenyu56@huawei.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: linux-usb@vger.kernel.org
Cc: devicetree@vger.kernel.org
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Yu Chen <chenyu56@huawei.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 drivers/usb/dwc3/core.h |  3 ++
 drivers/usb/dwc3/drd.c  | 77 ++++++++++++++++++++++++++++++++++++++++-
 2 files changed, 79 insertions(+), 1 deletion(-)

diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
index 77c4a9abe365..a99e57636172 100644
--- a/drivers/usb/dwc3/core.h
+++ b/drivers/usb/dwc3/core.h
@@ -25,6 +25,7 @@
 #include <linux/usb/ch9.h>
 #include <linux/usb/gadget.h>
 #include <linux/usb/otg.h>
+#include <linux/usb/role.h>
 #include <linux/ulpi/interface.h>
 
 #include <linux/phy/phy.h>
@@ -953,6 +954,7 @@ struct dwc3_scratchpad_array {
  * @hsphy_mode: UTMI phy mode, one of following:
  *		- USBPHY_INTERFACE_MODE_UTMI
  *		- USBPHY_INTERFACE_MODE_UTMIW
+ * @role_sw: usb_role_switch handle
  * @usb2_phy: pointer to USB2 PHY
  * @usb3_phy: pointer to USB3 PHY
  * @usb2_generic_phy: pointer to USB2 PHY
@@ -1086,6 +1088,7 @@ struct dwc3 {
 	struct extcon_dev	*edev;
 	struct notifier_block	edev_nb;
 	enum usb_phy_interface	hsphy_mode;
+	struct usb_role_switch	*role_sw;
 
 	u32			fladj;
 	u32			irq_gadget;
diff --git a/drivers/usb/dwc3/drd.c b/drivers/usb/dwc3/drd.c
index c946d64142ad..3b57d2ddda93 100644
--- a/drivers/usb/dwc3/drd.c
+++ b/drivers/usb/dwc3/drd.c
@@ -476,6 +476,73 @@ static struct extcon_dev *dwc3_get_extcon(struct dwc3 *dwc)
 	return edev;
 }
 
+#ifdef CONFIG_USB_ROLE_SWITCH
+#define ROLE_SWITCH 1
+static int dwc3_usb_role_switch_set(struct device *dev, enum usb_role role)
+{
+	struct dwc3 *dwc = dev_get_drvdata(dev);
+	u32 mode;
+
+	switch (role) {
+	case USB_ROLE_HOST:
+		mode = DWC3_GCTL_PRTCAP_HOST;
+		break;
+	case USB_ROLE_DEVICE:
+		mode = DWC3_GCTL_PRTCAP_DEVICE;
+		break;
+	default:
+		mode = DWC3_GCTL_PRTCAP_DEVICE;
+		break;
+	}
+
+	dwc3_set_mode(dwc, mode);
+	return 0;
+}
+
+static enum usb_role dwc3_usb_role_switch_get(struct device *dev)
+{
+	struct dwc3 *dwc = dev_get_drvdata(dev);
+	unsigned long flags;
+	enum usb_role role;
+
+	spin_lock_irqsave(&dwc->lock, flags);
+	switch (dwc->current_dr_role) {
+	case DWC3_GCTL_PRTCAP_HOST:
+		role = USB_ROLE_HOST;
+		break;
+	case DWC3_GCTL_PRTCAP_DEVICE:
+		role = USB_ROLE_DEVICE;
+		break;
+	case DWC3_GCTL_PRTCAP_OTG:
+		role = dwc->current_otg_role;
+		break;
+	default:
+		role = USB_ROLE_DEVICE;
+		break;
+	}
+	spin_unlock_irqrestore(&dwc->lock, flags);
+	return role;
+}
+
+static int dwc3_setup_role_switch(struct dwc3 *dwc)
+{
+	struct usb_role_switch_desc dwc3_role_switch = {NULL};
+
+	dwc3_role_switch.fwnode = dev_fwnode(dwc->dev);
+	dwc3_role_switch.set = dwc3_usb_role_switch_set;
+	dwc3_role_switch.get = dwc3_usb_role_switch_get;
+	dwc->role_sw = usb_role_switch_register(dwc->dev, &dwc3_role_switch);
+	if (IS_ERR(dwc->role_sw))
+		return PTR_ERR(dwc->role_sw);
+
+	dwc3_set_mode(dwc, DWC3_GCTL_PRTCAP_DEVICE);
+	return 0;
+}
+#else
+#define ROLE_SWITCH 0
+#define dwc3_setup_role_switch(x) 0
+#endif
+
 int dwc3_drd_init(struct dwc3 *dwc)
 {
 	int ret, irq;
@@ -484,7 +551,12 @@ int dwc3_drd_init(struct dwc3 *dwc)
 	if (IS_ERR(dwc->edev))
 		return PTR_ERR(dwc->edev);
 
-	if (dwc->edev) {
+	if (ROLE_SWITCH &&
+	    device_property_read_bool(dwc->dev, "usb-role-switch")) {
+		ret = dwc3_setup_role_switch(dwc);
+		if (ret < 0)
+			return ret;
+	} else if (dwc->edev) {
 		dwc->edev_nb.notifier_call = dwc3_drd_notifier;
 		ret = extcon_register_notifier(dwc->edev, EXTCON_USB_HOST,
 					       &dwc->edev_nb);
@@ -531,6 +603,9 @@ void dwc3_drd_exit(struct dwc3 *dwc)
 {
 	unsigned long flags;
 
+	if (dwc->role_sw)
+		usb_role_switch_unregister(dwc->role_sw);
+
 	if (dwc->edev)
 		extcon_unregister_notifier(dwc->edev, EXTCON_USB_HOST,
 					   &dwc->edev_nb);
-- 
2.25.0

[PATCH v3 08/19] dt-bindings: usb: generic: Add role-switch-default-mode binding

[Bryan O'Donoghue]

From: John Stultz <john.stultz@linaro.org>

Add binding to configure the default role the controller
assumes is host mode when the usb role is USB_ROLE_NONE.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
CC: ShuFan Lee <shufan_lee@richtek.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Yu Chen <chenyu56@huawei.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: linux-usb@vger.kernel.org
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 Documentation/devicetree/bindings/usb/generic.txt | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/usb/generic.txt b/Documentation/devicetree/bindings/usb/generic.txt
index cf5a1ad456e6..dd733fa81fad 100644
--- a/Documentation/devicetree/bindings/usb/generic.txt
+++ b/Documentation/devicetree/bindings/usb/generic.txt
@@ -34,6 +34,12 @@ Optional properties:
 			the USB data role (USB host or USB device) for a given
 			USB connector, such as Type-C, Type-B(micro).
 			see connector/usb-connector.txt.
+ - role-switch-default-mode: indicating if usb-role-switch is enabled, the
+			device default operation mode of controller while usb
+			role is USB_ROLE_NONE. Valid arguments are "host" and
+			"peripheral". Defaults to "peripheral" if not
+			specified.
+
 
 This is an attribute to a USB controller such as:
 
-- 
2.25.0

[PATCH v3 09/19] usb: dwc3: qcom: Override VBUS when using gpio_usb_connector

[Bryan O'Donoghue]

Using the gpio_usb_connector driver also means that we are not supplying
VBUS via the SoC but by an external PMIC directly.

This patch searches for a gpio_usb_connector as a child node of the core
DWC3 block and if found switches on the VBUS over-ride, leaving it up to
the role-switching code in gpio-usb-connector to switch off and on VBUS.

Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 drivers/usb/dwc3/dwc3-qcom.c | 17 ++++++++++++++---
 1 file changed, 14 insertions(+), 3 deletions(-)

diff --git a/drivers/usb/dwc3/dwc3-qcom.c b/drivers/usb/dwc3/dwc3-qcom.c
index 261af9e38ddd..73f9f3bcec59 100644
--- a/drivers/usb/dwc3/dwc3-qcom.c
+++ b/drivers/usb/dwc3/dwc3-qcom.c
@@ -550,6 +550,16 @@ static const struct dwc3_acpi_pdata sdm845_acpi_pdata = {
 	.ss_phy_irq_index = 2
 };
 
+static bool dwc3_qcom_find_gpio_usb_connector(struct platform_device *pdev)
+{
+	struct device_node	*np = pdev->dev.of_node;
+
+	if (of_get_child_by_name(np, "gpio_usb_connector"))
+		return true;
+
+	return false;
+}
+
 static int dwc3_qcom_probe(struct platform_device *pdev)
 {
 	struct device_node	*np = pdev->dev.of_node;
@@ -557,7 +567,7 @@ static int dwc3_qcom_probe(struct platform_device *pdev)
 	struct dwc3_qcom	*qcom;
 	struct resource		*res, *parent_res = NULL;
 	int			ret, i;
-	bool			ignore_pipe_clk;
+	bool			ignore_pipe_clk, gpio_usb_conn;
 
 	qcom = devm_kzalloc(&pdev->dev, sizeof(*qcom), GFP_KERNEL);
 	if (!qcom)
@@ -649,9 +659,10 @@ static int dwc3_qcom_probe(struct platform_device *pdev)
 	}
 
 	qcom->mode = usb_get_dr_mode(&qcom->dwc3->dev);
+	gpio_usb_conn = dwc3_qcom_find_gpio_usb_connector(qcom->dwc3);
 
-	/* enable vbus override for device mode */
-	if (qcom->mode == USB_DR_MODE_PERIPHERAL)
+	/* enable vbus override for device mode or GPIO USB connector mode */
+	if (qcom->mode == USB_DR_MODE_PERIPHERAL || gpio_usb_conn)
 		dwc3_qcom_vbus_overrride_enable(qcom, true);
 
 	/* register extcon to override sw_vbus on Vbus change later */
-- 
2.25.0

[PATCH v3 10/19] usb: dwc3: Add support for role-switch-default-mode binding

[Bryan O'Donoghue]

From: John Stultz <john.stultz@linaro.org>

Support the new role-switch-default-mode binding for configuring
the default role the controller assumes as when the usb role is
USB_ROLE_NONE

This patch was split out from a larger patch originally by
Yu Chen <chenyu56@huawei.com>

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
CC: ShuFan Lee <shufan_lee@richtek.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Yu Chen <chenyu56@huawei.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: linux-usb@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 drivers/usb/dwc3/core.h |  3 +++
 drivers/usb/dwc3/drd.c  | 25 ++++++++++++++++++++++---
 2 files changed, 25 insertions(+), 3 deletions(-)

diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
index a99e57636172..57d549a1ad0b 100644
--- a/drivers/usb/dwc3/core.h
+++ b/drivers/usb/dwc3/core.h
@@ -955,6 +955,8 @@ struct dwc3_scratchpad_array {
  *		- USBPHY_INTERFACE_MODE_UTMI
  *		- USBPHY_INTERFACE_MODE_UTMIW
  * @role_sw: usb_role_switch handle
+ * @role_switch_default_mode: default operation mode of controller while
+ *			usb role is USB_ROLE_NONE.
  * @usb2_phy: pointer to USB2 PHY
  * @usb3_phy: pointer to USB3 PHY
  * @usb2_generic_phy: pointer to USB2 PHY
@@ -1089,6 +1091,7 @@ struct dwc3 {
 	struct notifier_block	edev_nb;
 	enum usb_phy_interface	hsphy_mode;
 	struct usb_role_switch	*role_sw;
+	enum usb_dr_mode	role_switch_default_mode;
 
 	u32			fladj;
 	u32			irq_gadget;
diff --git a/drivers/usb/dwc3/drd.c b/drivers/usb/dwc3/drd.c
index 3b57d2ddda93..865341facece 100644
--- a/drivers/usb/dwc3/drd.c
+++ b/drivers/usb/dwc3/drd.c
@@ -491,7 +491,10 @@ static int dwc3_usb_role_switch_set(struct device *dev, enum usb_role role)
 		mode = DWC3_GCTL_PRTCAP_DEVICE;
 		break;
 	default:
-		mode = DWC3_GCTL_PRTCAP_DEVICE;
+		if (dwc->role_switch_default_mode == USB_DR_MODE_HOST)
+			mode = DWC3_GCTL_PRTCAP_HOST;
+		else
+			mode = DWC3_GCTL_PRTCAP_DEVICE;
 		break;
 	}
 
@@ -517,7 +520,10 @@ static enum usb_role dwc3_usb_role_switch_get(struct device *dev)
 		role = dwc->current_otg_role;
 		break;
 	default:
-		role = USB_ROLE_DEVICE;
+		if (dwc->role_switch_default_mode == USB_DR_MODE_HOST)
+			role = USB_ROLE_HOST;
+		else
+			role = USB_ROLE_DEVICE;
 		break;
 	}
 	spin_unlock_irqrestore(&dwc->lock, flags);
@@ -527,6 +533,19 @@ static enum usb_role dwc3_usb_role_switch_get(struct device *dev)
 static int dwc3_setup_role_switch(struct dwc3 *dwc)
 {
 	struct usb_role_switch_desc dwc3_role_switch = {NULL};
+	const char *str;
+	u32 mode;
+	int ret;
+
+	ret = device_property_read_string(dwc->dev, "role-switch-default-mode",
+					  &str);
+	if (ret >= 0  && !strncmp(str, "host", strlen("host"))) {
+		dwc->role_switch_default_mode = USB_DR_MODE_HOST;
+		mode = DWC3_GCTL_PRTCAP_HOST;
+	} else {
+		dwc->role_switch_default_mode = USB_DR_MODE_PERIPHERAL;
+		mode = DWC3_GCTL_PRTCAP_DEVICE;
+	}
 
 	dwc3_role_switch.fwnode = dev_fwnode(dwc->dev);
 	dwc3_role_switch.set = dwc3_usb_role_switch_set;
@@ -535,7 +554,7 @@ static int dwc3_setup_role_switch(struct dwc3 *dwc)
 	if (IS_ERR(dwc->role_sw))
 		return PTR_ERR(dwc->role_sw);
 
-	dwc3_set_mode(dwc, DWC3_GCTL_PRTCAP_DEVICE);
+	dwc3_set_mode(dwc, mode);
 	return 0;
 }
 #else
-- 
2.25.0

[PATCH v3 11/19] usb: dwc3: Add support for usb-conn-gpio connectors

[Bryan O'Donoghue]

This patch adds the ability to probe and enumerate a connector based on
usb-conn-gpio. A device node label gpio_usb_connector is used to identify
a usb-conn-gpio as a child of the USB interface.

You would use usb-conn-gpio when a regulator in your system provides VBUS
directly to the connector instead of supplying via the USB PHY.

The parent device must have the "usb-role-switch" property, so that when
the usb-conn-gpio driver calls usb_role_switch_set_role() the notification
in dwc3 will run and the block registers will be updated to match the state
detected at the connector.

Cc: John Stultz <john.stultz@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
CC: ShuFan Lee <shufan_lee@richtek.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Yu Chen <chenyu56@huawei.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: linux-usb@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 drivers/usb/dwc3/drd.c | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)

diff --git a/drivers/usb/dwc3/drd.c b/drivers/usb/dwc3/drd.c
index 865341facece..c6bb7cb809d5 100644
--- a/drivers/usb/dwc3/drd.c
+++ b/drivers/usb/dwc3/drd.c
@@ -11,6 +11,7 @@
 #include <linux/of_graph.h>
 #include <linux/platform_device.h>
 #include <linux/property.h>
+#include <linux/of_platform.h>
 
 #include "debug.h"
 #include "core.h"
@@ -557,9 +558,32 @@ static int dwc3_setup_role_switch(struct dwc3 *dwc)
 	dwc3_set_mode(dwc, mode);
 	return 0;
 }
+
+static int dwc3_register_gpio_usb_connector(struct dwc3 *dwc)
+{
+	struct device		*dev = dwc->dev;
+	struct device_node	*np = dev->of_node, *con_np;
+	int			ret;
+
+	con_np = of_get_child_by_name(np, "gpio_usb_connector");
+	if (!np) {
+		dev_dbg(dev, "no usb_connector child node specified\n");
+		return 0;
+	}
+
+	ret = of_platform_populate(np, NULL, NULL, dev);
+	if (ret) {
+		dev_err(dev, "failed to register usb_connector - %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
 #else
 #define ROLE_SWITCH 0
 #define dwc3_setup_role_switch(x) 0
+#define dwc3_register_gpio_usb_connector(x) 0
 #endif
 
 int dwc3_drd_init(struct dwc3 *dwc)
@@ -575,6 +599,9 @@ int dwc3_drd_init(struct dwc3 *dwc)
 		ret = dwc3_setup_role_switch(dwc);
 		if (ret < 0)
 			return ret;
+		ret = dwc3_register_gpio_usb_connector(dwc);
+		if (ret < 0)
+			return ret;
 	} else if (dwc->edev) {
 		dwc->edev_nb.notifier_call = dwc3_drd_notifier;
 		ret = extcon_register_notifier(dwc->edev, EXTCON_USB_HOST,
-- 
2.25.0

[PATCH v3 12/19] arm64: dts: qcom: qcs404: Add USB devices and PHYs

[Bryan O'Donoghue]

From: Bjorn Andersson <bjorn.andersson@linaro.org>

QCS404 sports HS and SS USB controllers based on dwc3 block with two HS
PHYs and one SS PHY. Add nodes for these devices and enable them for
EVB board.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 arch/arm64/boot/dts/qcom/qcs404.dtsi | 100 +++++++++++++++++++++++++++
 1 file changed, 100 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi
index f5f0c4c9cb16..73565a5b99d1 100644
--- a/arch/arm64/boot/dts/qcom/qcs404.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi
@@ -272,6 +272,48 @@ rpm_msg_ram: memory@60000 {
 			reg = <0x00060000 0x6000>;
 		};
 
+		usb3_phy: phy@78000 {
+			compatible = "qcom,usb-ssphy";
+			reg = <0x00078000 0x400>;
+			#phy-cells = <0>;
+			clocks = <&rpmcc RPM_SMD_LN_BB_CLK>,
+				 <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
+				 <&gcc GCC_USB3_PHY_PIPE_CLK>;
+			clock-names = "ref", "phy", "pipe";
+			resets = <&gcc GCC_USB3_PHY_BCR>,
+				 <&gcc GCC_USB3PHY_PHY_BCR>;
+			reset-names = "com", "phy";
+			status = "disabled";
+		};
+
+		usb2_phy_prim: phy@7a000 {
+			compatible = "qcom,qcs404-usb-hsphy";
+			reg = <0x0007a000 0x200>;
+			#phy-cells = <0>;
+			clocks = <&rpmcc RPM_SMD_LN_BB_CLK>,
+				 <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
+				 <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+			clock-names = "ref", "phy", "sleep";
+			resets = <&gcc GCC_USB_HS_PHY_CFG_AHB_BCR>,
+				 <&gcc GCC_USB2A_PHY_BCR>;
+			reset-names = "phy", "por";
+			status = "disabled";
+		};
+
+		usb2_phy_sec: phy@7c000 {
+			compatible = "qcom,qcs404-usb-hsphy";
+			reg = <0x0007c000 0x200>;
+			#phy-cells = <0>;
+			clocks = <&rpmcc RPM_SMD_LN_BB_CLK>,
+				 <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
+				 <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+			clock-names = "ref", "phy", "sleep";
+			resets = <&gcc GCC_QUSB2_PHY_BCR>,
+				 <&gcc GCC_USB2_HS_PHY_ONLY_BCR>;
+			reset-names = "phy", "por";
+			status = "disabled";
+		};
+
 		qfprom: qfprom@a4000 {
 			compatible = "qcom,qfprom";
 			reg = <0x000a4000 0x1000>;
@@ -379,6 +421,64 @@ glink-edge {
 			};
 		};
 
+		usb3: usb@7678800 {
+			compatible = "qcom,dwc3";
+			reg = <0x07678800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&gcc GCC_USB30_MASTER_CLK>,
+				 <&gcc GCC_SYS_NOC_USB3_CLK>,
+				 <&gcc GCC_USB30_SLEEP_CLK>,
+				 <&gcc GCC_USB30_MOCK_UTMI_CLK>;
+			clock-names = "core", "iface", "sleep", "mock_utmi";
+			assigned-clocks = <&gcc GCC_USB20_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <200000000>;
+			status = "disabled";
+
+			dwc3@7580000 {
+				compatible = "snps,dwc3";
+				reg = <0x07580000 0xcd00>;
+				interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&usb2_phy_sec>, <&usb3_phy>;
+				phy-names = "usb2-phy", "usb3-phy";
+				snps,has-lpm-erratum;
+				snps,hird-threshold = /bits/ 8 <0x10>;
+				snps,usb3_lpm_capable;
+				dr_mode = "otg";
+			};
+		};
+
+		usb2: usb@79b8800 {
+			compatible = "qcom,dwc3";
+			reg = <0x079b8800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>,
+				 <&gcc GCC_PCNOC_USB2_CLK>,
+				 <&gcc GCC_USB_HS_INACTIVITY_TIMERS_CLK>,
+				 <&gcc GCC_USB20_MOCK_UTMI_CLK>;
+			clock-names = "core", "iface", "sleep", "mock_utmi";
+			assigned-clocks = <&gcc GCC_USB20_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB_HS_SYSTEM_CLK>;
+			assigned-clock-rates = <19200000>, <133333333>;
+			status = "disabled";
+
+			dwc3@78c0000 {
+				compatible = "snps,dwc3";
+				reg = <0x078c0000 0xcc00>;
+				interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&usb2_phy_prim>;
+				phy-names = "usb2-phy";
+				snps,has-lpm-erratum;
+				snps,hird-threshold = /bits/ 8 <0x10>;
+				snps,usb3_lpm_capable;
+				dr_mode = "peripheral";
+			};
+		};
+
 		tlmm: pinctrl@1000000 {
 			compatible = "qcom,qcs404-pinctrl";
 			reg = <0x01000000 0x200000>,
-- 
2.25.0

[PATCH v3 13/19] arm64: dts: qcom: qcs404-evb: Define VBUS detect pin

[Bryan O'Donoghue]

VBUS present/absent is presented to the SoC via a GPIO on the EVB. Define
the pin mapping for later use by gpio-usb-conn.

Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 arch/arm64/boot/dts/qcom/qcs404-evb.dtsi | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
index 501a7330dbc8..6d53dc342f97 100644
--- a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
@@ -4,6 +4,8 @@
 #include <dt-bindings/gpio/gpio.h>
 #include "qcs404.dtsi"
 #include "pms405.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 
 / {
 	aliases {
@@ -270,6 +272,18 @@ rclk {
 	};
 };
 
+&pms405_gpios {
+	usb3_vbus_pin: usb3-vbus-pin {
+		pinconf {
+			pins = "gpio12";
+			function = PMIC_GPIO_FUNC_NORMAL;
+			input-enable;
+			bias-pull-down;
+			power-source = <1>;
+		};
+	};
+};
+
 &wifi {
 	status = "okay";
 	vdd-0.8-cx-mx-supply = <&vreg_l2_1p275>;
-- 
2.25.0

[PATCH v3 14/19] arm64: dts: qcom: qcs404-evb: Define VBUS boost pin

[Bryan O'Donoghue]

An external regulator is used to trigger VBUS on/off via GPIO. This patch
defines the relevant GPIO in the EVB dts.

Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 arch/arm64/boot/dts/qcom/qcs404-evb.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
index 6d53dc342f97..b6147b5ab5cb 100644
--- a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
@@ -273,6 +273,14 @@ rclk {
 };
 
 &pms405_gpios {
+	usb_vbus_boost_pin: usb-vbus-boost-pin {
+		pinconf {
+			pins = "gpio3";
+			function = PMIC_GPIO_FUNC_NORMAL;
+			output-low;
+			power-source = <1>;
+		};
+	};
 	usb3_vbus_pin: usb3-vbus-pin {
 		pinconf {
 			pins = "gpio12";
-- 
2.25.0

[PATCH v3 15/19] arm64: dts: qcom: qcs404-evb: Define USB ID pin

[Bryan O'Donoghue]

The USB ID pin is used to tell if a system is a Host or a Device. For our
purposes we will bind this pin into gpio-usb-conn later.

For now define the pin with its pinmux.

Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 arch/arm64/boot/dts/qcom/qcs404-evb.dtsi | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
index b6147b5ab5cb..abfb2a9a37e9 100644
--- a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
@@ -270,6 +270,20 @@ rclk {
 			bias-pull-down;
 		};
 	};
+
+	usb3_id_pin: usb3-id-pin {
+		pinmux {
+			pins = "gpio116";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio116";
+			drive-strength = <2>;
+			bias-pull-up;
+			input-enable;
+		};
+	};
 };
 
 &pms405_gpios {
-- 
2.25.0

[PATCH v3 16/19] arm64: dts: qcom: qcs404-evb: Describe external VBUS regulator

[Bryan O'Donoghue]

VBUS is supplied by an external regulator controlled by a GPIO pin. This
patch models the regulator as regulator-usb3-vbus.

Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 arch/arm64/boot/dts/qcom/qcs404-evb.dtsi | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
index abfb2a9a37e9..01ef59e8e5b7 100644
--- a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
@@ -33,6 +33,18 @@ vdd_esmps3_3p3: vdd-esmps3-3p3-regulator {
 		regulator-max-microvolt = <3300000>;
 		regulator-always-on;
 	};
+
+	usb3_vbus_reg: regulator-usb3-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "VBUS_BOOST_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&pms405_gpios 3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_vbus_boost_pin>;
+		vin-supply = <&vph_pwr>;
+		enable-active-high;
+	};
 };
 
 &blsp1_uart3 {
-- 
2.25.0

[PATCH v3 17/19] arm64: dts: qcom: qcs404-evb: Raise vreg_l12_3p3 minimum voltage

[Bryan O'Donoghue]

Rather than set the minimum microvolt for this regulator in the USB SS PHY
driver, set it in the DTS.

Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 arch/arm64/boot/dts/qcom/qcs404-evb.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
index 01ef59e8e5b7..0fff50f755ef 100644
--- a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
@@ -199,7 +199,7 @@ vreg_l11_sdc2: l11 {
 		};
 
 		vreg_l12_3p3: l12 {
-			regulator-min-microvolt = <2968000>;
+			regulator-min-microvolt = <3050000>;
 			regulator-max-microvolt = <3300000>;
 		};
 
-- 
2.25.0

[PATCH v3 18/19] arm64: dts: qcom: qcs404-evb: Enable secondary USB controller

[Bryan O'Donoghue]

This patch enables the second DWC3 controller which has one USB Hi-Speed
PHY attached to it.

Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 arch/arm64/boot/dts/qcom/qcs404-evb.dtsi | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
index 0fff50f755ef..07d6d793a922 100644
--- a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
@@ -318,6 +318,17 @@ pinconf {
 	};
 };
 
+&usb2 {
+	status = "okay";
+};
+
+&usb2_phy_sec {
+	vdd-supply = <&vreg_l4_1p2>;
+	vdda1p8-supply = <&vreg_l5_1p8>;
+	vdda3p3-supply = <&vreg_l12_3p3>;
+	status = "okay";
+};
+
 &wifi {
 	status = "okay";
 	vdd-0.8-cx-mx-supply = <&vreg_l2_1p275>;
-- 
2.25.0

[PATCH v3 19/19] arm64: dts: qcom: qcs404-evb: Enable primary USB controller

[Bryan O'Donoghue]

This patch enables the primary USB controller which has

- One USB3 SS PHY using gpio-usb-conn
- One USB2 HS PHY in device mode only and no connector driver
  associated.

Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 arch/arm64/boot/dts/qcom/qcs404-evb.dtsi | 29 ++++++++++++++++++++++++
 1 file changed, 29 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
index 07d6d793a922..a2cbca3a6124 100644
--- a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
@@ -329,6 +329,35 @@ &usb2_phy_sec {
 	status = "okay";
 };
 
+&usb3 {
+	status = "okay";
+	dwc3@7580000 {
+		usb-role-switch;
+		usb_con: gpio_usb_connector {
+			compatible = "gpio-usb-b-connector";
+			label = "USB-C";
+			id-gpio = <&tlmm 116 GPIO_ACTIVE_HIGH>;
+			vbus-supply = <&usb3_vbus_reg>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&usb3_id_pin>, <&usb3_vbus_pin>;
+			status = "okay";
+		};
+	};
+};
+
+&usb2_phy_prim {
+	vdd-supply = <&vreg_l4_1p2>;
+	vdda1p8-supply = <&vreg_l5_1p8>;
+	vdda3p3-supply = <&vreg_l12_3p3>;
+	status = "okay";
+};
+
+&usb3_phy {
+	vdd-supply = <&vreg_l3_1p05>;
+	vdda1p8-supply = <&vreg_l5_1p8>;
+	status = "okay";
+};
+
 &wifi {
 	status = "okay";
 	vdd-0.8-cx-mx-supply = <&vreg_l2_1p275>;
-- 
2.25.0

Re: [PATCH v3 05/19] phy: qualcomm: usb: Add SuperSpeed PHY driver

[Philipp Zabel]

Hi Bryan,

On Wed, 2020-01-22 at 18:55 +0000, Bryan O'Donoghue wrote:
> From: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> 
> Controls Qualcomm's SS phy 1.0.0 implemented in the QCS404 and some
> other Qualcomm platforms.
> 
> Based on Sriharsha Allenki's <sallenki@codeaurora.org> original code.
> 
> [bod: Removed dependency on extcon.
>       Switched to gpio-usb-conn to handle VBUS On/Off
>       Switched to usb-role-switch to bind gpio-usb-conn to DWC3]
> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> Cc: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@gmail.com>
> Cc: Sriharsha Allenki's <sallenki@codeaurora.org>
> Cc: Andy Gross <agross@kernel.org>
> Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
> Cc: Kishon Vijay Abraham I <kishon@ti.com>
> Cc: Philipp Zabel <p.zabel@pengutronix.de>
> Cc: linux-arm-msm@vger.kernel.org
> Cc: linux-kernel@vger.kernel.org
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>

regards
Philipp

Re: [PATCH v3 02/19] dt-bindings: phy: Add Qualcomm Synopsys Hi-Speed USB PHY binding

[Rob Herring]

On Wed, Jan 22, 2020 at 06:55:53PM +0000, Bryan O'Donoghue wrote:
> From: Sriharsha Allenki <sallenki@codeaurora.org>
> 
> Adds bindings for QCS404 USB PHY supporting Low-Speed, Full-Speed and
> Hi-Speed USB connectivity on Qualcomm chipsets.
> 
> [bod: Converted to YAML. Changed name dropping snps, 28nm components]
> 
> Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
> Signed-off-by: Anu Ramanathan <anur@codeaurora.org>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
> Cc: Andy Gross <agross@kernel.org>
> Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
> Cc: Kishon Vijay Abraham I <kishon@ti.com>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Mark Rutland <mark.rutland@arm.com>
> Cc: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@gmail.com>
> Cc: linux-arm-msm@vger.kernel.org
> Cc: linux-kernel@vger.kernel.org
> Cc: devicetree@vger.kernel.org
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
> ---
>  .../bindings/phy/qcom,qcs404-usb-hs.yaml      | 77 +++++++++++++++++++
>  1 file changed, 77 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/phy/qcom,qcs404-usb-hs.yaml
> 
> diff --git a/Documentation/devicetree/bindings/phy/qcom,qcs404-usb-hs.yaml b/Documentation/devicetree/bindings/phy/qcom,qcs404-usb-hs.yaml
> new file mode 100644
> index 000000000000..d71beb822ae2
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/qcom,qcs404-usb-hs.yaml
> @@ -0,0 +1,77 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: "http://devicetree.org/schemas/phy/qcom,qcs404-usb-hs.yaml#"
> +$schema: "http://devicetree.org/meta-schemas/core.yaml#"
> +
> +title: Qualcomm Synopsys QCS-404 High-Speed PHY
> +
> +maintainers:
> +  - Bryan O'Donoghue <bryan.odonoghue@linaro.org>
> +
> +description: |
> +  Qualcomm QCS-404 Low-Speed, Full-Speed, Hi-Speed USB PHY
> +
> +properties:
> +  compatible:
> +    enum:
> +      - qcom,qcs404-usb-hsphy
> +
> +  reg:
> +    maxItems: 1
> +    description: USB PHY base address and length of the register map.
> +
> +  "#phy-cells":
> +    const: 0
> +    description: Should be 0. See phy/phy-bindings.txt for details.
> +
> +  clocks:
> +    minItems: 3
> +    maxItems: 3
> +    description: phandles to rpmcc ref clock, PHY AHB clock, rentention clock.
> +
> +  clock-names:
> +    items:
> +      - const: ref
> +      - const: phy
> +      - const: sleep
> +
> +  resets:
> +    items:
> +      - description: PHY core reset
> +      - description: POR reset
> +
> +  reset-names:
> +    items:
> +      - const: phy
> +      - const: por
> +
> +  vdd-supply:
> +    maxItems: 1

Supplies are always 1 entry, so drop this.

> +    description: phandle to the regulator VDD supply node.
> +
> +  vdda1p8-supply:
> +    maxItems: 1
> +    description: phandle to the regulator 1.8V supply node.
> +
> +  vdda3p3-supply:
> +    maxItems: 1
> +    description: phandle to the regulator 3.3V supply node.

No required properties?

Add:

additionalProperties: false

> +
> +examples:
> +  - |
> +    #include <dt-bindings/clock/qcom,gcc-qcs404.h>
> +    #include <dt-bindings/clock/qcom,rpmcc.h>
> +    usb2_phy_prim: phy@7a000 {
> +        compatible = "qcom,qcs404-usb-hsphy";
> +        reg = <0x0007a000 0x200>;
> +        #phy-cells = <0>;
> +        clocks = <&rpmcc RPM_SMD_LN_BB_CLK>,
> +                 <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
> +                 <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
> +        clock-names = "ref", "phy", "sleep";
> +        resets = <&gcc GCC_USB_HS_PHY_CFG_AHB_BCR>,
> +                 <&gcc GCC_USB2A_PHY_BCR>;
> +        reset-names = "phy", "por";
> +    };
> +...
> -- 
> 2.25.0
> 

Re: [PATCH v3 04/19] dt-bindings: Add Qualcomm USB SuperSpeed PHY bindings

[Rob Herring]

On Wed, Jan 22, 2020 at 06:55:55PM +0000, Bryan O'Donoghue wrote:
> From: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> 
> Binding description for Qualcomm's Synopsys 1.0.0 SuperSpeed phy
> controller embedded in QCS404.
> 
> Based on Sriharsha Allenki's <sallenki@codeaurora.org> original
> definitions.
> 
> [bod: converted to yaml format]
> 
> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> Cc: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@gmail.com>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Mark Rutland <mark.rutland@arm.com>
> Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
> Cc: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@gmail.com>
> Cc: devicetree@vger.kernel.org
> Cc: linux-kernel@vger.kernel.org
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
> ---
>  .../bindings/phy/intel,lgm-emmc-phy.yaml      | 56 --------------

Working around errors? Should be fixed now, but not yet in linux-next.

>  .../devicetree/bindings/phy/qcom,usb-ss.yaml  | 75 +++++++++++++++++++
>  2 files changed, 75 insertions(+), 56 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/phy/intel,lgm-emmc-phy.yaml
>  create mode 100644 Documentation/devicetree/bindings/phy/qcom,usb-ss.yaml


> diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-ss.yaml b/Documentation/devicetree/bindings/phy/qcom,usb-ss.yaml
> new file mode 100644
> index 000000000000..3325b2f2e6a8
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/qcom,usb-ss.yaml
> @@ -0,0 +1,75 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: "http://devicetree.org/schemas/phy/qcom,usb-ss.yaml#"
> +$schema: "http://devicetree.org/meta-schemas/core.yaml#"
> +
> +title: Qualcomm Synopsys 1.0.0 SuperSpeed USB PHY
> +
> +maintainers:
> +  - Bryan O'Donoghue <bryan.odonoghue@linaro.org>
> +
> +description: |
> +  Qualcomm Synopsys 1.0.0 SuperSpeed USB PHY
> +
> +properties:
> +  compatible:
> +    enum:
> +      - qcom,usb-ssphy

Should be SoC specific.

> +
> +  reg:
> +    maxItems: 1
> +    description: USB PHY base address and length of the register map.

Can drop this. Doesn't really add anything.

> +
> +  "#phy-cells":
> +    const: 0
> +    description: Should be 0. See phy/phy-bindings.txt for details.

'Should be 0' is already expressed by the schema. The remaining 
reference isn't needed.

> +
> +  clocks:
> +    maxItems: 3
> +    minItems: 3
> +    description: phandles for rpmcc clock, PHY AHB clock, SuperSpeed pipe clock.

Split the description into 3 entries of 'items'. With that, 
minItems/maxItems is implicit.

> +
> +  clock-names:
> +    items:
> +      - const: ref
> +      - const: phy

'ahb' seems like a better name.

> +      - const: pipe
> +
> +  vdd-supply:
> +    maxItems: 1

Drop.

> +    description: phandle to the regulator VDD supply node.
> +
> +  vdda1p8-supply:
> +    maxItems: 1

Drop.

> +    description: phandle to the regulator 1.8V supply node.
> +
> +  resets:
> +    items:
> +      - description: COM reset
> +      - description: PHY reset line
> +
> +  reset-names:
> +    items:
> +      - const: com
> +      - const: phy

required and additionalProperties needed.

> +examples:
> +  - |
> +    #include <dt-bindings/clock/qcom,gcc-qcs404.h>
> +    #include <dt-bindings/clock/qcom,rpmcc.h>
> +    usb3_phy: usb3-phy@78000 {
> +        compatible = "qcom,usb-ssphy";
> +        reg = <0x78000 0x400>;
> +        #phy-cells = <0>;
> +        clocks = <&rpmcc RPM_SMD_LN_BB_CLK>,
> +                 <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
> +                 <&gcc GCC_USB3_PHY_PIPE_CLK>;
> +        clock-names = "ref", "phy", "pipe";
> +        resets = <&gcc GCC_USB3_PHY_BCR>,
> +                 <&gcc GCC_USB3PHY_PHY_BCR>;
> +        reset-names = "com", "phy";
> +        vdd-supply = <&vreg_l3_1p05>;
> +        vdda1p8-supply = <&vreg_l5_1p8>;
> +    };
> +...
> -- 
> 2.25.0
> 

Re: [PATCH v3 06/19] dt-bindings: usb: dwc3: Add a gpio-usb-connector description

[Rob Herring]

On Wed, Jan 22, 2020 at 06:55:57PM +0000, Bryan O'Donoghue wrote:
> A USB connector should be a child node of the USB controller
> connector/usb-connector.txt. This patch adds a property
> "gpio_usb_connector" which declares a connector child device. Code in the
> DWC3 driver will then
> 
> - Search for "gpio_usb_controller"
> - Do an of_platform_populate() if found
> 
> This will have the effect of making the declared node a child of the USB
> controller and will make sure that USB role-switch events detected with the
> gpio_usb_controller driver propagate into the DWC3 controller code
> appropriately.

This is all driver specifics. This is a binding patch.

> 
> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Mark Rutland <mark.rutland@arm.com>
> Cc: linux-usb@vger.kernel.org
> Cc: devicetree@vger.kernel.org
> Cc: linux-kernel@vger.kernel.org
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
> ---
>  Documentation/devicetree/bindings/usb/dwc3.txt | 11 +++++++++++
>  1 file changed, 11 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt
> index 66780a47ad85..b019bd472f83 100644
> --- a/Documentation/devicetree/bindings/usb/dwc3.txt
> +++ b/Documentation/devicetree/bindings/usb/dwc3.txt
> @@ -108,6 +108,9 @@ Optional properties:
>  			When just one value, which means INCRX burst mode enabled. When
>  			more than one value, which means undefined length INCR burst type
>  			enabled. The values can be 1, 4, 8, 16, 32, 64, 128 and 256.
> + - gpio_usb_connector: Declares a USB connector named 'gpio_usb_connector' as a
> +		       child node of the DWC3 block. Use when modelling a USB
> +		       connector based on the gpio-usb-b-connector driver.

Should be just 'connector'. That's already implicitly allowed for any 
USB controller, so you don't really need a binding change. And the 
specific type of connector is outside the scope of the DWC3 binding.

>  
>   - in addition all properties from usb-xhci.txt from the current directory are
>     supported as well
> @@ -121,4 +124,12 @@ dwc3@4a030000 {
>  	interrupts = <0 92 4>
>  	usb-phy = <&usb2_phy>, <&usb3,phy>;
>  	snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
> +	usb_con: gpio_usb_connector {
> +		compatible = "gpio-usb-b-connector";
> +		id-gpio = <&tlmm 116 GPIO_ACTIVE_HIGH>;
> +		vbus-gpio = <&pms405_gpios 12 GPIO_ACTIVE_HIGH>;

*-gpios is the preferred form and should be what's documented.

> +		vbus-supply = <&usb3_vbus_reg>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&usb3_id_pin>, <&usb3_vbus_pin>;
> +	};
>  };
> -- 
> 2.25.0
> 

Re: [PATCH v3 06/19] dt-bindings: usb: dwc3: Add a gpio-usb-connector description

[Felipe Balbi]

[-- Attachment #1: Type: text/plain, Size: 1055 bytes --]


Hi,

Bryan O'Donoghue <bryan.odonoghue@linaro.org> writes:

> A USB connector should be a child node of the USB controller
> connector/usb-connector.txt. This patch adds a property
> "gpio_usb_connector" which declares a connector child device. Code in the
> DWC3 driver will then
>
> - Search for "gpio_usb_controller"
> - Do an of_platform_populate() if found
>
> This will have the effect of making the declared node a child of the USB
> controller and will make sure that USB role-switch events detected with the
> gpio_usb_controller driver propagate into the DWC3 controller code
> appropriately.
>
> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Mark Rutland <mark.rutland@arm.com>
> Cc: linux-usb@vger.kernel.org
> Cc: devicetree@vger.kernel.org
> Cc: linux-kernel@vger.kernel.org
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

I'm assuming this will go together with the rest of the series:

Acked-by: Felipe Balbi <balbi@kernel.org>

-- 
balbi

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 832 bytes --]

Re: [PATCH v3 07/19] usb: dwc3: Registering a role switch in the DRD code.

[Felipe Balbi]

[-- Attachment #1: Type: text/plain, Size: 4522 bytes --]


Hi,

Bryan O'Donoghue <bryan.odonoghue@linaro.org> writes:
> From: Yu Chen <chenyu56@huawei.com>
>
> The Type-C drivers use USB role switch API to inform the
> system about the negotiated data role, so registering a role
> switch in the DRD code in order to support platforms with
> USB Type-C connectors.
>
> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Mark Rutland <mark.rutland@arm.com>
> CC: ShuFan Lee <shufan_lee@richtek.com>
> Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
> Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
> Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
> Cc: Yu Chen <chenyu56@huawei.com>
> Cc: Felipe Balbi <balbi@kernel.org>
> Cc: Hans de Goede <hdegoede@redhat.com>
> Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
> Cc: Jun Li <lijun.kernel@gmail.com>
> Cc: Valentin Schneider <valentin.schneider@arm.com>
> Cc: Jack Pham <jackp@codeaurora.org>
> Cc: linux-usb@vger.kernel.org
> Cc: devicetree@vger.kernel.org
> Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
> Signed-off-by: Yu Chen <chenyu56@huawei.com>
> Signed-off-by: John Stultz <john.stultz@linaro.org>
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
> ---
>  drivers/usb/dwc3/core.h |  3 ++
>  drivers/usb/dwc3/drd.c  | 77 ++++++++++++++++++++++++++++++++++++++++-
>  2 files changed, 79 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
> index 77c4a9abe365..a99e57636172 100644
> --- a/drivers/usb/dwc3/core.h
> +++ b/drivers/usb/dwc3/core.h
> @@ -25,6 +25,7 @@
>  #include <linux/usb/ch9.h>
>  #include <linux/usb/gadget.h>
>  #include <linux/usb/otg.h>
> +#include <linux/usb/role.h>
>  #include <linux/ulpi/interface.h>
>  
>  #include <linux/phy/phy.h>
> @@ -953,6 +954,7 @@ struct dwc3_scratchpad_array {
>   * @hsphy_mode: UTMI phy mode, one of following:
>   *		- USBPHY_INTERFACE_MODE_UTMI
>   *		- USBPHY_INTERFACE_MODE_UTMIW
> + * @role_sw: usb_role_switch handle
>   * @usb2_phy: pointer to USB2 PHY
>   * @usb3_phy: pointer to USB3 PHY
>   * @usb2_generic_phy: pointer to USB2 PHY
> @@ -1086,6 +1088,7 @@ struct dwc3 {
>  	struct extcon_dev	*edev;
>  	struct notifier_block	edev_nb;
>  	enum usb_phy_interface	hsphy_mode;
> +	struct usb_role_switch	*role_sw;
>  
>  	u32			fladj;
>  	u32			irq_gadget;
> diff --git a/drivers/usb/dwc3/drd.c b/drivers/usb/dwc3/drd.c
> index c946d64142ad..3b57d2ddda93 100644
> --- a/drivers/usb/dwc3/drd.c
> +++ b/drivers/usb/dwc3/drd.c
> @@ -476,6 +476,73 @@ static struct extcon_dev *dwc3_get_extcon(struct dwc3 *dwc)
>  	return edev;
>  }
>  
> +#ifdef CONFIG_USB_ROLE_SWITCH

it's best to use if (IS_*()) macros.

> +#define ROLE_SWITCH 1

this wouldn't be neceessary

> +static int dwc3_usb_role_switch_set(struct device *dev, enum usb_role role)
> +{
> +	struct dwc3 *dwc = dev_get_drvdata(dev);
> +	u32 mode;
> +
> +	switch (role) {
> +	case USB_ROLE_HOST:
> +		mode = DWC3_GCTL_PRTCAP_HOST;
> +		break;
> +	case USB_ROLE_DEVICE:
> +		mode = DWC3_GCTL_PRTCAP_DEVICE;
> +		break;
> +	default:
> +		mode = DWC3_GCTL_PRTCAP_DEVICE;
> +		break;
> +	}
> +
> +	dwc3_set_mode(dwc, mode);
> +	return 0;
> +}
> +
> +static enum usb_role dwc3_usb_role_switch_get(struct device *dev)
> +{
> +	struct dwc3 *dwc = dev_get_drvdata(dev);
> +	unsigned long flags;
> +	enum usb_role role;
> +
> +	spin_lock_irqsave(&dwc->lock, flags);
> +	switch (dwc->current_dr_role) {
> +	case DWC3_GCTL_PRTCAP_HOST:
> +		role = USB_ROLE_HOST;
> +		break;
> +	case DWC3_GCTL_PRTCAP_DEVICE:
> +		role = USB_ROLE_DEVICE;
> +		break;
> +	case DWC3_GCTL_PRTCAP_OTG:
> +		role = dwc->current_otg_role;
> +		break;
> +	default:
> +		role = USB_ROLE_DEVICE;
> +		break;
> +	}
> +	spin_unlock_irqrestore(&dwc->lock, flags);
> +	return role;
> +}
> +
> +static int dwc3_setup_role_switch(struct dwc3 *dwc)
> +{
> +	struct usb_role_switch_desc dwc3_role_switch = {NULL};
> +
> +	dwc3_role_switch.fwnode = dev_fwnode(dwc->dev);
> +	dwc3_role_switch.set = dwc3_usb_role_switch_set;
> +	dwc3_role_switch.get = dwc3_usb_role_switch_get;
> +	dwc->role_sw = usb_role_switch_register(dwc->dev, &dwc3_role_switch);
> +	if (IS_ERR(dwc->role_sw))
> +		return PTR_ERR(dwc->role_sw);
> +
> +	dwc3_set_mode(dwc, DWC3_GCTL_PRTCAP_DEVICE);
> +	return 0;
> +}
> +#else
> +#define ROLE_SWITCH 0
> +#define dwc3_setup_role_switch(x) 0

or this

-- 
balbi

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 832 bytes --]

Re: [PATCH v3 09/19] usb: dwc3: qcom: Override VBUS when using gpio_usb_connector

[Felipe Balbi]

[-- Attachment #1: Type: text/plain, Size: 986 bytes --]


Hi,

Bryan O'Donoghue <bryan.odonoghue@linaro.org> writes:

> Using the gpio_usb_connector driver also means that we are not supplying
> VBUS via the SoC but by an external PMIC directly.
>
> This patch searches for a gpio_usb_connector as a child node of the core
> DWC3 block and if found switches on the VBUS over-ride, leaving it up to
> the role-switching code in gpio-usb-connector to switch off and on VBUS.
>
> Cc: Andy Gross <agross@kernel.org>
> Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
> Cc: Lee Jones <lee.jones@linaro.org>
> Cc: Felipe Balbi <balbi@kernel.org>
> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> Cc: Philipp Zabel <p.zabel@pengutronix.de>
> Cc: linux-arm-msm@vger.kernel.org
> Cc: linux-usb@vger.kernel.org
> Cc: linux-kernel@vger.kernel.org
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
> ---

assuming it'll go with the rest of the series:

Acked-by: Felipe Balbi <balbi@kernel.org>

-- 
balbi

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 832 bytes --]

Re: [PATCH v3 10/19] usb: dwc3: Add support for role-switch-default-mode binding

[Felipe Balbi]

[-- Attachment #1: Type: text/plain, Size: 377 bytes --]


Hi,

Bryan O'Donoghue <bryan.odonoghue@linaro.org> writes:
> From: John Stultz <john.stultz@linaro.org>
>
> Support the new role-switch-default-mode binding for configuring
> the default role the controller assumes as when the usb role is
> USB_ROLE_NONE

per specification, device is supposed to be the default role. Why isn't
that working for you?

-- 
balbi

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 832 bytes --]

Re: [PATCH v3 10/19] usb: dwc3: Add support for role-switch-default-mode binding

[Bryan O'Donoghue]

On 31/01/2020 13:29, Felipe Balbi wrote:
> 
> Hi,
> 
> Bryan O'Donoghue <bryan.odonoghue@linaro.org> writes:
>> From: John Stultz <john.stultz@linaro.org>
>>
>> Support the new role-switch-default-mode binding for configuring
>> the default role the controller assumes as when the usb role is
>> USB_ROLE_NONE
> 
> per specification, device is supposed to be the default role. Why isn't
> that working for you?
> 

Speaking for myself - its only the role-switch logic I need. This patch 
seemed to go along with the the role-switch stuff but, now that you ask, 
this series can probably do without it.

---
bod

Re: [PATCH v3 10/19] usb: dwc3: Add support for role-switch-default-mode binding

[Felipe Balbi]

[-- Attachment #1: Type: text/plain, Size: 728 bytes --]


Hi,

Bryan O'Donoghue <bryan.odonoghue@linaro.org> writes:
>> Bryan O'Donoghue <bryan.odonoghue@linaro.org> writes:
>>> From: John Stultz <john.stultz@linaro.org>
>>>
>>> Support the new role-switch-default-mode binding for configuring
>>> the default role the controller assumes as when the usb role is
>>> USB_ROLE_NONE
>> 
>> per specification, device is supposed to be the default role. Why isn't
>> that working for you?
>
> Speaking for myself - its only the role-switch logic I need. This patch 
> seemed to go along with the the role-switch stuff but, now that you ask, 
> this series can probably do without it.

Oh, cool. Then we can defer this until we find an actual use for it :-)

-- 
balbi

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 832 bytes --]

Re: [PATCH v3 06/19] dt-bindings: usb: dwc3: Add a gpio-usb-connector description

[Bryan O'Donoghue]

On 27/01/2020 18:43, Rob Herring wrote:
> On Wed, Jan 22, 2020 at 06:55:57PM +0000, Bryan O'Donoghue wrote:
>> A USB connector should be a child node of the USB controller
>> connector/usb-connector.txt. This patch adds a property
>> "gpio_usb_connector" which declares a connector child device. Code in the
>> DWC3 driver will then
>>
>> - Search for "gpio_usb_controller"
>> - Do an of_platform_populate() if found
>>
>> This will have the effect of making the declared node a child of the USB
>> controller and will make sure that USB role-switch events detected with the
>> gpio_usb_controller driver propagate into the DWC3 controller code
>> appropriately.
> 
> This is all driver specifics. This is a binding patch.
> 
>>
>> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
>> Cc: Rob Herring <robh+dt@kernel.org>
>> Cc: Mark Rutland <mark.rutland@arm.com>
>> Cc: linux-usb@vger.kernel.org
>> Cc: devicetree@vger.kernel.org
>> Cc: linux-kernel@vger.kernel.org
>> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
>> ---
>>   Documentation/devicetree/bindings/usb/dwc3.txt | 11 +++++++++++
>>   1 file changed, 11 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt
>> index 66780a47ad85..b019bd472f83 100644
>> --- a/Documentation/devicetree/bindings/usb/dwc3.txt
>> +++ b/Documentation/devicetree/bindings/usb/dwc3.txt
>> @@ -108,6 +108,9 @@ Optional properties:
>>   			When just one value, which means INCRX burst mode enabled. When
>>   			more than one value, which means undefined length INCR burst type
>>   			enabled. The values can be 1, 4, 8, 16, 32, 64, 128 and 256.
>> + - gpio_usb_connector: Declares a USB connector named 'gpio_usb_connector' as a
>> +		       child node of the DWC3 block. Use when modelling a USB
>> +		       connector based on the gpio-usb-b-connector driver.
> 
> Should be just 'connector'. That's already implicitly allowed for any
> USB controller, so you don't really need a binding change. And the
> specific type of connector is outside the scope of the DWC3 binding.
> 
>>   
>>    - in addition all properties from usb-xhci.txt from the current directory are
>>      supported as well
>> @@ -121,4 +124,12 @@ dwc3@4a030000 {
>>   	interrupts = <0 92 4>
>>   	usb-phy = <&usb2_phy>, <&usb3,phy>;
>>   	snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
>> +	usb_con: gpio_usb_connector {
>> +		compatible = "gpio-usb-b-connector";
>> +		id-gpio = <&tlmm 116 GPIO_ACTIVE_HIGH>;
>> +		vbus-gpio = <&pms405_gpios 12 GPIO_ACTIVE_HIGH>;
> 
> *-gpios is the preferred form and should be what's documented.

Hi Rob,

If I've understood you right here you don't favour documenting a new 
binding but you're OK with adding an example ?

---
bod