* [PATCH v5 0/2] Add base device tree files for QDU1000/QRU1000
@ 2022-12-16 23:27 Melody Olvera
2022-12-16 23:27 ` [PATCH v5 1/2] arm64: dts: qcom: Add base QDU1000/QRU1000 DTSIs Melody Olvera
2022-12-16 23:27 ` [PATCH v5 2/2] arm64: dts: qcom: Add base QDU1000/QRU1000 IDP DTs Melody Olvera
0 siblings, 2 replies; 5+ messages in thread
From: Melody Olvera @ 2022-12-16 23:27 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski
Cc: linux-arm-msm, devicetree, linux-kernel, Melody Olvera
This series adds the base device tree files and DTS support for the
Qualcomm QDU1000 and QRU1000 IDP SoCs, including the clocks, tlmm, smmu,
regulators, mmc, interconnects, cpufreq, and qup.
This patchset requires the dt-bindings cahnges from [1-7].
The Qualcomm Technologies, Inc. Distributed Unit 1000 and Radio Unit
1000 are new SoCs meant for enabling Open RAN solutions. See more at
https://www.qualcomm.com/content/dam/qcomm-martech/dm-assets/documents/qualcomm_5g_ran_platforms_product_brief.pdf
[1] https://lore.kernel.org/lkml/20221216230722.21404-2-quic_molvera@quicinc.com/
[2] https://lore.kernel.org/lkml/20221216230852.21691-2-quic_molvera@quicinc.com/
[3] https://lore.kernel.org/lkml/20221216230914.21771-2-quic_molvera@quicinc.com/
[4] https://lore.kernel.org/lkml/20221216231312.22574-1-quic_molvera@quicinc.com/
[5] https://lore.kernel.org/lkml/20221216231349.22835-1-quic_molvera@quicinc.com/
[6] https://lore.kernel.org/lkml/20221216231426.24760-1-quic_molvera@quicinc.com/
[7] https://lore.kernel.org/lkml/20221216231513.25085-1-quic_molvera@quicinc.com/
Changes from v4:
- Added chassis-type
- Added missing regulator voltages
- Sorted includes
- Remaned memory nodes
- Reorganized nodes to start with compatible/reg
- Removed unnecessary clocks
- Switched to deleting nodes by label
- Moved pin biases and drive strengths to dts files
Changes from v3:
- added PCIE and USB clocks
- added missing qdu1000 compats
Changes from v2:
- Revised device nodes to match updated dt-bindings
- Revised rpmh-rsc bindings to allow for generic regulator nodes
- Updated soc ordering
- Moved clock node to DTS files
- Updated regulator nodes to be generic
- Removed some unnecessary whitespace
Melody Olvera (2):
arm64: dts: qcom: Add base QDU1000/QRU1000 DTSIs
arm64: dts: qcom: Add base QDU1000/QRU1000 IDP DTs
arch/arm64/boot/dts/qcom/Makefile | 2 +
arch/arm64/boot/dts/qcom/qdu1000-idp.dts | 453 ++++++++
arch/arm64/boot/dts/qcom/qdu1000.dtsi | 1334 ++++++++++++++++++++++
arch/arm64/boot/dts/qcom/qru1000-idp.dts | 453 ++++++++
arch/arm64/boot/dts/qcom/qru1000.dtsi | 26 +
5 files changed, 2268 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/qdu1000-idp.dts
create mode 100644 arch/arm64/boot/dts/qcom/qdu1000.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/qru1000-idp.dts
create mode 100644 arch/arm64/boot/dts/qcom/qru1000.dtsi
base-commit: ca39c4daa6f7f770b1329ffb46f1e4a6bcc3f291
prerequisite-patch-id: 33dc185eb002163bc54d0638d7adf1acb5389370
prerequisite-patch-id: c55ff1a38fed5356caa8f40a85ef0b8ebc4d1fa4
prerequisite-patch-id: 527e8f51e8f8f113d80952f26215ecbe491ba39e
prerequisite-patch-id: a6ce10162dcf7c392bf8318363081d7ef6749679
prerequisite-patch-id: d5d17b3d720b358b8478cb1ad87e21a70992f228
prerequisite-patch-id: 6c92672973fdc1524516942fa21c340e68e7c4fb
prerequisite-patch-id: 89c175b9874a926a7cc10d0dbae3a192d9b089dd
prerequisite-patch-id: 4a3c6a10c0070c0f411605aad07d664e20b01830
prerequisite-patch-id: 0a0f671fae0526d96f745ff1329b0ff8cbec1082
--
2.38.1
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH v5 1/2] arm64: dts: qcom: Add base QDU1000/QRU1000 DTSIs
2022-12-16 23:27 [PATCH v5 0/2] Add base device tree files for QDU1000/QRU1000 Melody Olvera
@ 2022-12-16 23:27 ` Melody Olvera
2022-12-17 14:59 ` Konrad Dybcio
2022-12-16 23:27 ` [PATCH v5 2/2] arm64: dts: qcom: Add base QDU1000/QRU1000 IDP DTs Melody Olvera
1 sibling, 1 reply; 5+ messages in thread
From: Melody Olvera @ 2022-12-16 23:27 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski
Cc: linux-arm-msm, devicetree, linux-kernel, Melody Olvera
Add the base DTSI files for QDU1000 and QRU1000 SoCs, including base
descriptions of CPUs, GCC, RPMHCC, QUP, TLMM, and interrupt-controller
to boot to shell with console on these SoCs.
Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>
---
arch/arm64/boot/dts/qcom/qdu1000.dtsi | 1334 +++++++++++++++++++++++++
arch/arm64/boot/dts/qcom/qru1000.dtsi | 26 +
2 files changed, 1360 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/qdu1000.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/qru1000.dtsi
diff --git a/arch/arm64/boot/dts/qcom/qdu1000.dtsi b/arch/arm64/boot/dts/qcom/qdu1000.dtsi
new file mode 100644
index 000000000000..244007a488a3
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qdu1000.dtsi
@@ -0,0 +1,1334 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,qdu1000-gcc.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/dma/qcom-gpi.h>
+#include <dt-bindings/interconnect/qcom,qdu1000-rpmh.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+
+/ {
+ interrupt-parent = <&intc>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ chosen: chosen { };
+
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ CPU0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x0 0x0>;
+ enable-method = "psci";
+ power-domain-names = "psci";
+ power-domains = <&CPU_PD0>;
+ qcom,freq-domains = <&cpufreq_hw 0>;
+ next-level-cache = <&L2_0>;
+ L2_0: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ L3_0: l3-cache {
+ compatible = "cache";
+ };
+ };
+ };
+
+ CPU1: cpu@100 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x0 0x100>;
+ enable-method = "psci";
+ power-domains = <&CPU_PD1>;
+ power-domain-names = "psci";
+ qcom,freq-domains = <&cpufreq_hw 0>;
+ next-level-cache = <&L2_100>;
+ L2_100: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU2: cpu@200 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x0 0x200>;
+ enable-method = "psci";
+ power-domains = <&CPU_PD2>;
+ power-domain-names = "psci";
+ qcom,freq-domains = <&cpufreq_hw 0>;
+ next-level-cache = <&L2_200>;
+ L2_200: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU3: cpu@300 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x0 0x300>;
+ enable-method = "psci";
+ power-domains = <&CPU_PD3>;
+ power-domain-names = "psci";
+ qcom,freq-domains = <&cpufreq_hw 0>;
+ next-level-cache = <&L2_300>;
+ L2_300: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&CPU0>;
+ };
+
+ core1 {
+ cpu = <&CPU1>;
+ };
+
+ core2 {
+ cpu = <&CPU2>;
+ };
+
+ core3 {
+ cpu = <&CPU3>;
+ };
+ };
+ };
+ };
+
+ idle-states {
+ entry-method = "psci";
+
+ CPU_OFF: cpu-sleep-0 {
+ compatible = "arm,idle-state";
+ entry-latency-us = <274>;
+ exit-latency-us = <480>;
+ min-residency-us = <3934>;
+ arm,psci-suspend-param = <0x40000004>;
+ local-timer-stop;
+ };
+ };
+
+ domain-idle-states {
+ CLUSTER_SLEEP_0: cluster-sleep-0 {
+ compatible = "domain-idle-state";
+ entry-latency-us = <584>;
+ exit-latency-us = <2332>;
+ min-residency-us = <6118>;
+ arm,psci-suspend-param = <0x41000044>;
+ };
+
+ CLUSTER_SLEEP_1: cluster-sleep-1 {
+ compatible = "domain-idle-state";
+ entry-latency-us = <2893>;
+ exit-latency-us = <4023>;
+ min-residency-us = <9987>;
+ arm,psci-suspend-param = <0x41003344>;
+ };
+ };
+
+ firmware {
+ scm {
+ compatible = "qcom,scm-qdu1000", "qcom,scm";
+ };
+ };
+
+ mc_virt: interconnect-0 {
+ compatible = "qcom,qdu1000-mc-virt";
+ #interconnect-cells = <2>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ clk_virt: interconnect-1 {
+ compatible = "qcom,qdu1000-clk-virt";
+ #interconnect-cells = <2>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ /* We expect the bootloader to fill in the size */
+ reg = <0x0 0x80000000 0x0 0x0>;
+ };
+
+ pmu {
+ compatible = "arm,armv8-pmuv3";
+ interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+
+ CPU_PD0: power-domain-cpu0 {
+ #power-domain-cells = <0>;
+ power-domains = <&CLUSTER_PD>;
+ domain-idle-states = <&CPU_OFF>;
+ };
+
+ CPU_PD1: power-domain-cpu1 {
+ #power-domain-cells = <0>;
+ power-domains = <&CLUSTER_PD>;
+ domain-idle-states = <&CPU_OFF>;
+ };
+
+ CPU_PD2: power-domain-cpu2 {
+ #power-domain-cells = <0>;
+ power-domains = <&CLUSTER_PD>;
+ domain-idle-states = <&CPU_OFF>;
+ };
+
+ CPU_PD3: power-domain-cpu3 {
+ #power-domain-cells = <0>;
+ power-domains = <&CLUSTER_PD>;
+ domain-idle-states = <&CPU_OFF>;
+ };
+
+ CLUSTER_PD: power-domain-cluster {
+ #power-domain-cells = <0>;
+ domain-idle-states = <&CLUSTER_SLEEP_0 &CLUSTER_SLEEP_1>;
+ };
+ };
+
+ reserved_memory: reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ hyp_mem: hyp@80000000 {
+ reg = <0x0 0x80000000 0x0 0x600000>;
+ no-map;
+ };
+
+ xbl_dt_log_mem: xbl-dt-log@80600000 {
+ reg = <0x0 0x80600000 0x0 0x40000>;
+ no-map;
+ };
+
+ xbl_ramdump_mem: xbl-ramdump@80640000 {
+ reg = <0x0 0x80640000 0x0 0x1c0000>;
+ no-map;
+ };
+
+ aop_image_mem: aop-image@80800000 {
+ reg = <0x0 0x80800000 0x0 0x60000>;
+ no-map;
+ };
+
+ aop_cmd_db_mem: aop-cmd-db@80860000 {
+ compatible = "qcom,cmd-db";
+ reg = <0x0 0x80860000 0x0 0x20000>;
+ no-map;
+ };
+
+ aop_config_mem: aop-config@80880000 {
+ reg = <0x0 0x80880000 0x0 0x20000>;
+ no-map;
+ };
+
+ tme_crash_dump_mem: tme-crash-dump@808a0000 {
+ reg = <0x0 0x808a0000 0x0 0x40000>;
+ no-map;
+ };
+
+ tme_log_mem: tme-log@808e0000 {
+ reg = <0x0 0x808e0000 0x0 0x4000>;
+ no-map;
+ };
+
+ uefi_log_mem: uefi-log@808e4000 {
+ reg = <0x0 0x808e4000 0x0 0x10000>;
+ no-map;
+ };
+
+ /* secdata region can be reused by apps */
+
+ smem_mem: smem@80900000 {
+ compatible = "qcom,smem";
+ reg = <0x0 0x80900000 0x0 0x200000>;
+ no-map;
+ hwlocks = <&tcsr_mutex 3>;
+ };
+
+ cpucp_fw_mem: cpucp-fw@80b00000 {
+ reg = <0x0 0x80b00000 0x0 0x100000>;
+ no-map;
+ };
+
+ xbl_sc_mem: memory@80c00000 {
+ reg = <0x0 0x80c00000 0x0 0x40000>;
+ no-map;
+ };
+
+ /* uefi region can be reused by apps */
+
+ tz_stat_mem: tz-stat@81d00000 {
+ reg = <0x0 0x81d00000 0x0 0x100000>;
+ no-map;
+ };
+
+ tags_mem: tags@81e00000 {
+ reg = <0x0 0x81e00000 0x0 0x500000>;
+ no-map;
+ };
+
+ qtee_mem: qtee@82300000 {
+ reg = <0x0 0x82300000 0x0 0x500000>;
+ no-map;
+ };
+
+ ta_mem: ta@82800000 {
+ reg = <0x0 0x82800000 0x0 0xa00000>;
+ no-map;
+ };
+
+ fs1_mem: fs1@83200000 {
+ reg = <0x0 0x83200000 0x0 0x400000>;
+ no-map;
+ };
+
+ fs2_mem: fs2@83600000 {
+ reg = <0x0 0x83600000 0x0 0x400000>;
+ no-map;
+ };
+
+ fs3_mem: fs3@83a00000 {
+ reg = <0x0 0x83a00000 0x0 0x400000>;
+ no-map;
+ };
+
+ /* Linux kernel image is loaded at 0x83e00000 */
+
+ ipa_fw_mem: ipa-fw@8be00000 {
+ reg = <0x0 0x8be00000 0x0 0x10000>;
+ no-map;
+ };
+
+ ipa_gsi_mem: ipa-gsi@8be10000 {
+ reg = <0x0 0x8be10000 0x0 0x14000>;
+ no-map;
+ };
+
+ mpss_mem: mpss@8c000000 {
+ reg = <0x0 0x8c000000 0x0 0x12c00000>;
+ no-map;
+ };
+
+ q6_mpss_dtb_mem: q6-mpss-dtb@9ec00000 {
+ reg = <0x0 0x9ec00000 0x0 0x80000>;
+ no-map;
+ };
+
+ tenx_mem: tenx@a0000000 {
+ reg = <0x0 0xa0000000 0x0 0x19600000>;
+ no-map;
+ };
+
+ oem_tenx_mem: oem-tenx@b9600000 {
+ reg = <0x0 0xb9600000 0x0 0x6a00000>;
+ no-map;
+ };
+
+ tenx_q6_buffer_mem: tenx-q6-buffer@c0000000 {
+ reg = <0x0 0xc0000000 0x0 0x3200000>;
+ no-map;
+ };
+
+ ipa_buffer_mem: ipa-buffer@c3200000 {
+ reg = <0x0 0xc3200000 0x0 0x12c00000>;
+ no-map;
+ };
+ };
+
+ soc: soc@0 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0 0 0 0 0x10 0>;
+ dma-ranges = <0 0 0 0 0x10 0>;
+ compatible = "simple-bus";
+
+ gcc: clock-controller@80000 {
+ compatible = "qcom,qdu1000-gcc";
+ reg = <0x0 0x80000 0x0 0x1f4200>;
+ clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>, <0>, <0>, <0>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+ };
+
+ gpi_dma0: dma-controller@900000 {
+ compatible = "qcom,qdu1000-gpi-dma", "qcom,sm6350-gpi-dma";
+ reg = <0x0 0x900000 0x0 0x60000>;
+ interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
+ dma-channels = <12>;
+ dma-channel-mask = <0x3f>;
+ iommus = <&apps_smmu 0xf6 0x0>;
+ #dma-cells = <3>;
+ };
+
+ qupv3_id_0: geniqup@9c0000 {
+ compatible = "qcom,geni-se-qup";
+ reg = <0x0 0x9c0000 0x0 0x2000>;
+ clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
+ <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+ clock-names = "m-ahb", "s-ahb";
+ iommus = <&apps_smmu 0xe3 0x0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0
+ &clk_virt SLAVE_QUP_CORE_0 0>;
+ interconnect-names = "qup-core";
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ uart0: serial@980000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x0 0x980000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart0_default>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@984000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x984000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c1_data_clk>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi1: spi@984000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x984000 0x0 0x4000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi1_data_clk>, <&qup_spi1_cs>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@988000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x988000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c2_data_clk>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi2: spi@988000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x988000 0x0 0x4000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi2_data_clk>, <&qup_spi2_cs>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@98c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x98c000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c3_data_clk>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi3: spi@98c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x98c000 0x0 0x4000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi3_data_clk>, <&qup_spi3_cs>;
+ status = "disabled";
+ };
+
+ i2c4: i2c@990000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x990000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c4_data_clk>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi4: spi@990000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x990000 0x0 0x4000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi4_data_clk>, <&qup_spi4_cs>;
+ status = "disabled";
+ };
+
+ i2c5: i2c@994000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x994000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c5_data_clk>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi5: spi@994000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x994000 0x0 0x4000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi5_data_clk>, <&qup_spi5_cs>;
+ status = "disabled";
+ };
+
+ i2c6: i2c@998000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x998000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c6_data_clk>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi6: spi@998000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x998000 0x0 0x4000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi6_data_clk>, <&qup_spi6_cs>;
+ status = "disabled";
+ };
+
+ uart7: serial@99c000 {
+ compatible = "qcom,geni-debug-uart";
+ reg = <0x0 0x99c000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart7_tx>, <&qup_uart7_rx>;
+ interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+ };
+
+ gpi_dma1: dma-controller@a00000 {
+ compatible = "qcom,qdu1000-gpi-dma", "qcom,sm6350-gpi-dma";
+ reg = <0x0 0xa00000 0x0 0x60000>;
+ interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>;
+ dma-channels = <12>;
+ dma-channel-mask = <0x3f>;
+ iommus = <&apps_smmu 0x116 0x0>;
+ #dma-cells = <3>;
+ };
+
+ qupv3_id_1: geniqup@ac0000 {
+ compatible = "qcom,geni-se-qup";
+ reg = <0x0 0xac0000 0x0 0x2000>;
+ clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+ <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+ clock-names = "m-ahb", "s-ahb";
+ iommus = <&apps_smmu 0x103 0x0>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ ranges;
+ status = "disabled";
+
+ uart8: serial@a80000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x0 0xa80000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart8_default>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c9: i2c@a84000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0xa84000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c9_data_clk>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi9: spi@a84000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0xa84000 0x0 0x4000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi9_data_clk>, <&qup_spi9_cs>;
+ status = "disabled";
+ };
+
+ i2c10: i2c@a88000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0xa88000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c10_data_clk>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi10: spi@a88000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0xa88000 0x0 0x4000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs>;
+ status = "disabled";
+ };
+
+ i2c11: i2c@a8c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0xa8c000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c11_data_clk>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi11: spi@a8c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0xa8c000 0x0 0x4000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi11_data_clk>, <&qup_spi11_cs>;
+ status = "disabled";
+ };
+
+ i2c12: i2c@a90000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0xa90000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c12_data_clk>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi12: spi@a90000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0xa90000 0x0 0x4000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi12_data_clk>, <&qup_spi12_cs>;
+ status = "disabled";
+ };
+
+ i2c13: i2c@a94000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0xa94000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c13_data_clk>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart13: serial@a94000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x0 0xa94000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart13_default>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi13: spi@a94000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0xa94000 0x0 0x4000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi13_data_clk>, <&qup_spi13_cs>;
+ status = "disabled";
+ };
+
+ i2c14: i2c@a98000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0xa98000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+ interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c14_data_clk>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi14: spi@a98000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0xa98000 0x0 0x4000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi14_data_clk>, <&qup_spi14_cs>;
+ status = "disabled";
+ };
+
+ i2c15: i2c@a9c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0xa9c000 0x0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+ interrupts = <GIC_SPI 365 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-0 = <&qup_i2c15_data_clk>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi15: spi@a9c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0xa9c000 0x0 0x4000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 365 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi15_data_clk>, <&qup_spi15_cs>;
+ status = "disabled";
+ };
+ };
+
+ system_noc: interconnect@1640000 {
+ compatible = "qcom,qdu1000-system-noc";
+ reg = <0x0 0x1640000 0x0 0x45080>;
+ #interconnect-cells = <2>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ tcsr_mutex: hwlock@1f40000 {
+ compatible = "qcom,tcsr-mutex";
+ reg = <0x0 0x1f40000 0x0 0x20000>;
+ #hwlock-cells = <1>;
+ };
+
+ pdc: interrupt-controller@b220000 {
+ compatible = "qcom,qdu1000-pdc", "qcom,pdc";
+ reg = <0x0 0xb220000 0x0 0x30000>, <0x0 0x174000f0 0x0 0x64>;
+ qcom,pdc-ranges = <0 480 12>, <14 494 24>, <40 520 54>,
+ <94 609 31>, <125 63 1>;
+ #interrupt-cells = <2>;
+ interrupt-parent = <&intc>;
+ interrupt-controller;
+ };
+
+ spmi_bus: spmi@c400000 {
+ compatible = "qcom,spmi-pmic-arb";
+ reg = <0x0 0xc400000 0x0 0x3000>,
+ <0x0 0xc500000 0x0 0x400000>,
+ <0x0 0xc440000 0x0 0x80000>,
+ <0x0 0xc4c0000 0x0 0x10000>,
+ <0x0 0xc42d000 0x0 0x4000>;
+ reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+ interrupt-names = "periph_irq";
+ interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
+ qcom,ee = <0>;
+ qcom,channel = <0>;
+ #address-cells = <2>;
+ #size-cells = <0>;
+ interrupt-controller;
+ #interrupt-cells = <4>;
+ };
+
+ tlmm: pinctrl@f000000 {
+ compatible = "qcom,qdu1000-tlmm";
+ reg = <0x0 0xf000000 0x0 0x1000000>;
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-ranges = <&tlmm 0 0 151>;
+ wakeup-parent = <&pdc>;
+
+ qup_uart0_default: qup-uart0-default-state {
+ pins = "gpio6", "gpio7", "gpio8", "gpio9";
+ function = "qup00";
+ };
+
+ qup_i2c1_data_clk: qup-i2c1-data-clk-state {
+ pins = "gpio10", "gpio11";
+ function = "qup01";
+ };
+
+ qup_spi1_data_clk: qup-spi1-data-clk-state {
+ pins = "gpio10", "gpio11", "gpio12";
+ function = "qup01";
+ };
+
+ qup_spi1_cs: qup-spi1-cs-state {
+ pins = "gpio13";
+ function = "gpio";
+ };
+
+ qup_i2c2_data_clk: qup-i2c2-data-clk-state {
+ pins = "gpio12", "gpio13";
+ function = "qup02";
+ };
+
+ qup_spi2_data_clk: qup-spi2-data-clk-state {
+ pins = "gpio12", "gpio13", "gpio10";
+ function = "qup02";
+ };
+
+ qup_spi2_cs: qup-spi2-cs-state {
+ pins = "gpio11";
+ function = "gpio";
+ };
+
+ qup_i2c3_data_clk: qup-i2c3-data-clk-state {
+ pins = "gpio14", "gpio15";
+ function = "qup03";
+ };
+
+ qup_spi3_data_clk: qup-spi3-data-clk-state {
+ pins = "gpio14", "gpio15", "gpio16";
+ function = "qup03";
+ };
+
+ qup_spi3_cs: qup-spi3-cs-state {
+ pins = "gpio17";
+ function = "gpio";
+ };
+
+ qup_i2c4_data_clk: qup-i2c4-data-clk-state {
+ pins = "gpio16", "gpio17";
+ function = "qup04";
+ };
+
+ qup_spi4_data_clk: qup-spi4-data-clk-state {
+ pins = "gpio16", "gpio17", "gpio14";
+ function = "qup04";
+ };
+
+ qup_spi4_cs: qup-spi4-cs-state {
+ pins = "gpio15";
+ function = "gpio";
+ };
+
+ qup_i2c5_data_clk: qup-i2c5-data-clk-state {
+ pins = "gpio130", "gpio131";
+ function = "qup05";
+ };
+
+ qup_spi5_data_clk: qup-spi5-data-clk-state {
+ pins = "gpio130", "gpio131", "gpio132";
+ function = "qup05";
+ };
+
+ qup_spi5_cs: qup-spi5-cs-state {
+ pins = "gpio133";
+ function = "gpio";
+ };
+
+ qup_i2c6_data_clk: qup-i2c6-data-clk-state {
+ pins = "gpio132", "gpio133";
+ function = "qup06";
+ };
+
+ qup_spi6_data_clk: qup-spi6-data-clk-state {
+ pins = "gpio132", "gpio133", "gpio130";
+ function = "qup06";
+ };
+
+ qup_spi6_cs: qup-spi6-cs-state {
+ pins = "gpio131";
+ function = "gpio";
+ };
+
+ qup_uart7_rx: qup-uart7-rx-state {
+ pins = "gpio135";
+ function = "qup07";
+ };
+
+ qup_uart7_tx: qup-uart7-tx-state {
+ pins = "gpio134";
+ function = "qup07";
+ };
+
+ qup_uart8_default: qup-uart8-default-state {
+ pins = "gpio18", "gpio19", "gpio20", "gpio21";
+ function = "qup10";
+ };
+
+ qup_i2c9_data_clk: qup-i2c9-data-clk-state {
+ pins = "gpio22", "gpio23";
+ function = "qup11";
+ };
+
+ qup_spi9_data_clk: qup-spi9-data-clk-state {
+ pins = "gpio22", "gpio23", "gpio24";
+ function = "qup11";
+ };
+
+ qup_spi9_cs: qup-spi9-cs-state {
+ pins = "gpio25";
+ function = "gpio";
+ };
+
+ qup_i2c10_data_clk: qup-i2c10-data-clk-state {
+ pins = "gpio24", "gpio25";
+ function = "qup12";
+ };
+
+ qup_spi10_data_clk: qup-spi10-data-clk-state {
+ pins = "gpio24", "gpio25", "gpio22";
+ function = "qup12";
+ };
+
+ qup_spi10_cs: qup-spi10-cs-state {
+ pins = "gpio23";
+ function = "gpio";
+ };
+
+ qup_i2c11_data_clk: qup-i2c11-data-clk-state {
+ pins = "gpio26", "gpio27";
+ function = "qup13";
+ };
+
+ qup_spi11_data_clk: qup-spi11-data-clk-state {
+ pins = "gpio26", "gpio27", "gpio28";
+ function = "qup13";
+ };
+
+ qup_spi11_cs: qup-spi11-cs-state {
+ pins = "gpio29";
+ function = "gpio";
+ };
+
+ qup_i2c12_data_clk: qup-i2c12-data-clk-state {
+ pins = "gpio28", "gpio29";
+ function = "qup14";
+ };
+
+ qup_spi12_data_clk: qup-spi12-data-clk-state {
+ pins = "gpio28", "gpio29", "gpio26";
+ function = "qup14";
+ };
+
+ qup_spi12_cs: qup-spi12-cs-state {
+ pins = "gpio27";
+ function = "gpio";
+ };
+
+ qup_i2c13_data_clk: qup-i2c13-data-clk-state {
+ pins = "gpio30", "gpio31";
+ function = "qup15";
+ };
+
+ qup_spi13_data_clk: qup-spi13-data-clk-state {
+ pins = "gpio30", "gpio31", "gpio32";
+ function = "qup15";
+ };
+
+ qup_spi13_cs: qup-spi13-cs-state {
+ pins = "gpio33";
+ function = "gpio";
+ };
+
+ qup_uart13_default: qup-uart13-default-state {
+ pins = "gpio30", "gpio31", "gpio32", "gpio33";
+ function = "qup15";
+ };
+
+ qup_i2c14_data_clk: qup-i2c14-data-clk-state {
+ pins = "gpio34", "gpio35";
+ function = "qup16";
+ };
+
+ qup_spi14_data_clk: qup-spi14-data-clk-state {
+ pins = "gpio34", "gpio35", "gpio36";
+ function = "qup16";
+ };
+
+ qup_spi14_cs: qup-spi14-cs-state {
+ pins = "gpio37", "gpio38";
+ function = "gpio";
+ };
+
+ qup_i2c15_data_clk: qup-i2c15-data-clk-state {
+ pins = "gpio40", "gpio41";
+ function = "qup17";
+ };
+
+ qup_spi15_data_clk: qup-spi15-data-clk-state {
+ pins = "gpio40", "gpio41", "gpio30";
+ function = "qup17";
+ };
+
+ qup_spi15_cs: qup-spi15-cs-state {
+ pins = "gpio31";
+ function = "gpio";
+ };
+ };
+
+ apps_smmu: iommu@15000000 {
+ compatible = "qcom,qdu1000-smmu-500", "arm,mmu-500";
+ reg = <0x0 0x15000000 0x0 0x100000>;
+ #iommu-cells = <2>;
+ #global-interrupts = <2>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 426 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 671 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 672 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ intc: interrupt-controller@17200000 {
+ compatible = "arm,gic-v3";
+ reg = <0x0 0x17200000 0x0 0x10000>, /* GICD */
+ <0x0 0x17260000 0x0 0x80000>; /* GICR * 4 */
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ #redistributor-regions = <1>;
+ redistributor-stride = <0x0 0x20000>;
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ timer@17420000 {
+ compatible = "arm,armv7-timer-mem";
+ reg = <0x0 0x17420000 0x0 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ frame@17421000 {
+ reg = <0x17421000 0x1000>,
+ <0x17422000 0x1000>;
+ frame-number = <0>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ frame@17423000 {
+ reg = <0x17423000 0x1000>;
+ frame-number = <1>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ frame@17425000 {
+ reg = <0x17425000 0x1000>,
+ <0x17426000 0x1000>;
+ frame-number = <2>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ frame@17427000 {
+ reg = <0x17427000 0x1000>;
+ frame-number = <3>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ frame@17429000 {
+ reg = <0x17429000 0x1000>;
+ frame-number = <4>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ frame@1742b000 {
+ reg = <0x1742b000 0x1000>;
+ frame-number = <5>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ frame@1742d000 {
+ reg = <0x1742d000 0x1000>;
+ frame-number = <6>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+ };
+
+ apps_rsc: rsc@17a00000 {
+ compatible = "qcom,rpmh-rsc";
+ reg = <0x0 0x17a00000 0x0 0x10000>,
+ <0x0 0x17a10000 0x0 0x10000>,
+ <0x0 0x17a20000 0x0 0x10000>;
+ reg-names = "drv-0", "drv-1", "drv-2";
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ qcom,tcs-offset = <0xd00>;
+ qcom,drv-id = <2>;
+ qcom,tcs-config = <ACTIVE_TCS 2>, <SLEEP_TCS 3>,
+ <WAKE_TCS 3>, <CONTROL_TCS 0>;
+ label = "apps_rsc";
+
+ apps_bcm_voter: bcm-voter {
+ compatible = "qcom,bcm-voter";
+ };
+
+ rpmhcc: clock-controller {
+ compatible = "qcom,qdu1000-rpmh-clk";
+ #clock-cells = <1>;
+ clock-names = "xo";
+ clocks = <&xo_board>;
+ };
+
+ rpmhpd: power-controller {
+ compatible = "qcom,qdu1000-rpmhpd";
+ #power-domain-cells = <1>;
+ operating-points-v2 = <&rpmhpd_opp_table>;
+
+ rpmhpd_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ rpmhpd_opp_ret: opp1 {
+ opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
+ };
+
+ rpmhpd_opp_min_svs: opp2 {
+ opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+ };
+
+ rpmhpd_opp_low_svs: opp3 {
+ opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+ };
+
+ rpmhpd_opp_svs: opp4 {
+ opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+ };
+
+ rpmhpd_opp_svs_l1: opp5 {
+ opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+ };
+
+ rpmhpd_opp_nom: opp6 {
+ opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+ };
+
+ rpmhpd_opp_nom_l1: opp7 {
+ opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+ };
+
+ rpmhpd_opp_nom_l2: opp8 {
+ opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
+ };
+
+ rpmhpd_opp_turbo: opp9 {
+ opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+ };
+
+ rpmhpd_opp_turbo_l1: opp10 {
+ opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+ };
+ };
+ };
+ };
+
+ cpufreq_hw: cpufreq@17d90000 {
+ compatible = "qcom,qdu1000-cpufreq-epss", "qcom,cpufreq-epss";
+ reg = <0x0 0x17d90000 0x0 0x1000>, <0x0 0x17d91000 0x0 0x1000>;
+ reg-names = "freq-domain0", "freq-domain1";
+ clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>;
+ clock-names = "xo", "alternate";
+ #freq-domain-cells = <1>;
+ };
+
+ gem_noc: interconnect@19100000 {
+ compatible = "qcom,qdu1000-gem-noc";
+ reg = <0x0 0x19100000 0x0 0xB8080>;
+ #interconnect-cells = <2>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+ };
+
+ arch_timer: timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 12 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
+ clock-frequency = <19200000>;
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/qru1000.dtsi b/arch/arm64/boot/dts/qcom/qru1000.dtsi
new file mode 100644
index 000000000000..eac5dc54a8ab
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qru1000.dtsi
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include "qdu1000.dtsi"
+/delete-node/ &tenx_mem;
+/delete-node/ &oem_tenx_mem;
+/delete-node/ &tenx_q6_buffer_mem;
+
+&reserved_memory {
+ oem_tenx_mem: oem-tenx@a0000000 {
+ reg = <0x0 0xa0000000 0x0 0x6400000>;
+ no-map;
+ };
+
+ mpss_diag_buffer_mem: mpss-diag-buffer@aea00000 {
+ reg = <0x0 0xaea00000 0x0 0x6400000>;
+ no-map;
+ };
+
+ tenx_q6_buffer_mem: tenx-q6-buffer@b4e00000 {
+ reg = <0x0 0xb4e00000 0x0 0x3200000>;
+ no-map;
+ };
+};
--
2.38.1
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH v5 2/2] arm64: dts: qcom: Add base QDU1000/QRU1000 IDP DTs
2022-12-16 23:27 [PATCH v5 0/2] Add base device tree files for QDU1000/QRU1000 Melody Olvera
2022-12-16 23:27 ` [PATCH v5 1/2] arm64: dts: qcom: Add base QDU1000/QRU1000 DTSIs Melody Olvera
@ 2022-12-16 23:27 ` Melody Olvera
1 sibling, 0 replies; 5+ messages in thread
From: Melody Olvera @ 2022-12-16 23:27 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski
Cc: linux-arm-msm, devicetree, linux-kernel, Melody Olvera
Add DTs for Qualcomm IDP platforms using the QDU1000 and QRU1000
SoCs.
Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>
---
arch/arm64/boot/dts/qcom/Makefile | 2 +
arch/arm64/boot/dts/qcom/qdu1000-idp.dts | 453 +++++++++++++++++++++++
arch/arm64/boot/dts/qcom/qru1000-idp.dts | 453 +++++++++++++++++++++++
3 files changed, 908 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/qdu1000-idp.dts
create mode 100644 arch/arm64/boot/dts/qcom/qru1000-idp.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 3e79496292e7..4d06a6ff5194 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -56,8 +56,10 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-poplar.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8998-xiaomi-sagit.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
+dtb-$(CONFIG_ARCH_QCOM) += qdu1000-idp.dtb
dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5.dtb
dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5-vision-mezzanine.dtb
+dtb-$(CONFIG_ARCH_QCOM) += qru1000-idp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sa8155p-adp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sa8295p-adp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sa8540p-ride.dtb
diff --git a/arch/arm64/boot/dts/qcom/qdu1000-idp.dts b/arch/arm64/boot/dts/qcom/qdu1000-idp.dts
new file mode 100644
index 000000000000..9e9fd4b8023e
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qdu1000-idp.dts
@@ -0,0 +1,453 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "qdu1000.dtsi"
+#include "pm8150.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. QDU1000 IDP";
+ compatible = "qcom,qdu1000-idp", "qcom,qdu1000";
+ chassis-type = "embedded";
+
+ aliases {
+ serial0 = &uart7;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ clocks {
+ xo_board: xo-board-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <19200000>;
+ #clock-cells = <0>;
+ };
+
+ sleep_clk: sleep-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <32000>;
+ #clock-cells = <0>;
+ };
+ };
+
+ ppvar_sys: ppvar-sys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "ppvar_sys";
+ regulator-min-microvolt = <4200000>;
+ regulator-max-microvolt = <4200000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+
+ vin-supply = <&ppvar_sys>;
+ };
+};
+
+&apps_rsc {
+ regulators {
+ compatible = "qcom,pm8150-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-s6-supply = <&vph_pwr>;
+ vdd-s7-supply = <&vph_pwr>;
+ vdd-s8-supply = <&vph_pwr>;
+ vdd-s9-supply = <&vph_pwr>;
+ vdd-s10-supply = <&vph_pwr>;
+
+ vdd-l1-l8-l11-supply = <&vreg_s6a_0p9>;
+ vdd-l2-l10-supply = <&vph_pwr>;
+ vdd-l3-l4-l5-l18-supply = <&vreg_s5a_2p0>;
+ vdd-l6-l9-supply = <&vreg_s6a_0p9>;
+ vdd-l7-l12-l14-l15-supply = <&vreg_s4a_1p8>;
+ vdd-l13-l16-l17-supply = <&vph_pwr>;
+
+ vreg_s2a_0p5: smps2 {
+ regulator-name = "vreg_s2a_0p5";
+ regulator-min-microvolt = <320000>;
+ regulator-max-microvolt = <570000>;
+ };
+
+ vreg_s3a_1p05: smps3 {
+ regulator-name = "vreg_s3a_1p05";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1170000>;
+ };
+
+ vreg_s4a_1p8: smps4 {
+ regulator-name = "vreg_s4a_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vreg_s5a_2p0: smps5 {
+ regulator-name = "vreg_s5a_2p0";
+ regulator-min-microvolt = <1904000>;
+ regulator-max-microvolt = <2000000>;
+ };
+
+ vreg_s6a_0p9: smps6 {
+ regulator-name = "vreg_s6a_0p9";
+ regulator-min-microvolt = <920000>;
+ regulator-max-microvolt = <1128000>;
+ };
+
+ vreg_s7a_1p2: smps7 {
+ regulator-name = "vreg_s7a_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ vreg_s8a_1p3: smps8 {
+ regulator-name = "vreg_s8a_1p3";
+ regulator-min-microvolt = <1352000>;
+ regulator-max-microvolt = <1352000>;
+ };
+
+ vreg_l1a_0p91: ldo1 {
+ regulator-name = "vreg_l1a_0p91";
+ regulator-min-microvolt = <312000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l2a_2p3: ldo2 {
+ regulator-name = "vreg_l2a_2p3";
+ regulator-min-microvolt = <2970000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l3a_1p2: ldo3 {
+ regulator-name = "vreg_l3a_1p2";
+ regulator-min-microvolt = <920000>;
+ regulator-max-microvolt = <1260000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l5a_0p8: ldo5 {
+ regulator-name = "vreg_l5a_0p8";
+ regulator-min-microvolt = <312000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l6a_0p91: ldo6 {
+ regulator-name = "vreg_l6a_0p91";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <950000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l7a_1p8: ldo7 {
+ regulator-name = "vreg_l7a_1p8";
+ regulator-min-microvolt = <1650000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+
+ };
+
+ vreg_l8a_0p91: ldo8 {
+ regulator-name = "vreg_l8a_0p91";
+ regulator-min-microvolt = <888000>;
+ regulator-max-microvolt = <925000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l9a_0p91: ldo9 {
+ regulator-name = "vreg_l9a_0p91";
+ regulator-min-microvolt = <312000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l10a_2p95: ldo10 {
+ regulator-name = "vreg_l10a_2p95";
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3544000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l11a_0p91: ldo11 {
+ regulator-name = "vreg_l11a_0p91";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l12a_1p8: ldo12 {
+ regulator-name = "vreg_l12a_1p8";
+ regulator-min-microvolt = <1504000>;
+ regulator-max-microvolt = <1504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l14a_1p8: ldo14 {
+ regulator-name = "vreg_l14a_1p8";
+ regulator-min-microvolt = <1650000>;
+ regulator-max-microvolt = <1950000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l15a_1p8: ldo15 {
+ regulator-name = "vreg_l15a_1p8";
+ regulator-min-microvolt = <1504000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l16a_1p8: ldo16 {
+ regulator-name = "vreg_l16a_1p8";
+ regulator-min-microvolt = <1710000>;
+ regulator-max-microvolt = <1890000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l17a_3p3: ldo17 {
+ regulator-name = "vreg_l17a_3p3";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3544000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l18a_1p2: ldo18 {
+ regulator-name = "vreg_l18a_1p2";
+ regulator-min-microvolt = <312000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+ };
+};
+
+&qup_i2c1_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_i2c2_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_i2c3_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_i2c4_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_i2c5_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_i2c6_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_i2c9_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_i2c10_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_i2c11_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_i2c12_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_i2c13_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_i2c14_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_i2c15_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_spi1_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi1_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi2_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi2_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi3_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi3_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi4_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi4_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi5_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi5_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi6_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi6_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi9_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi9_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi10_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi10_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi11_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi11_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi12_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi12_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi13_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi13_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi14_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi14_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi15_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi15_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_uart7_rx {
+ drive-strength = <2>;
+ bias-disable;
+};
+
+&qup_uart7_tx {
+ drive-strength = <2>;
+ bias-disable;
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&uart7 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/qru1000-idp.dts b/arch/arm64/boot/dts/qcom/qru1000-idp.dts
new file mode 100644
index 000000000000..2cc893ae4d10
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qru1000-idp.dts
@@ -0,0 +1,453 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "qru1000.dtsi"
+#include "pm8150.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. QRU1000 IDP";
+ compatible = "qcom,qru1000-idp", "qcom,qru1000";
+ chassis-type = "embedded";
+
+ aliases {
+ serial0 = &uart7;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ clocks {
+ xo_board: xo-board-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <19200000>;
+ #clock-cells = <0>;
+ };
+
+ sleep_clk: sleep-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <32000>;
+ #clock-cells = <0>;
+ };
+ };
+
+ ppvar_sys: ppvar-sys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "ppvar_sys";
+ regulator-min-microvolt = <4200000>;
+ regulator-max-microvolt = <4200000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+
+ vin-supply = <&ppvar_sys>;
+ };
+};
+
+&apps_rsc {
+ regulators {
+ compatible = "qcom,pm8150-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-s6-supply = <&vph_pwr>;
+ vdd-s7-supply = <&vph_pwr>;
+ vdd-s8-supply = <&vph_pwr>;
+ vdd-s9-supply = <&vph_pwr>;
+ vdd-s10-supply = <&vph_pwr>;
+
+ vdd-l1-l8-l11-supply = <&vreg_s6a_0p9>;
+ vdd-l2-l10-supply = <&vph_pwr>;
+ vdd-l3-l4-l5-l18-supply = <&vreg_s5a_2p0>;
+ vdd-l6-l9-supply = <&vreg_s6a_0p9>;
+ vdd-l7-l12-l14-l15-supply = <&vreg_s4a_1p8>;
+ vdd-l13-l16-l17-supply = <&vph_pwr>;
+
+ vreg_s2a_0p5: smps2 {
+ regulator-name = "vreg_s2a_0p5";
+ regulator-min-microvolt = <320000>;
+ regulator-max-microvolt = <570000>;
+ };
+
+ vreg_s3a_1p05: smps3 {
+ regulator-name = "vreg_s3a_1p05";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1170000>;
+ };
+
+ vreg_s4a_1p8: smps4 {
+ regulator-name = "vreg_s4a_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vreg_s5a_2p0: smps5 {
+ regulator-name = "vreg_s5a_2p0";
+ regulator-min-microvolt = <1904000>;
+ regulator-max-microvolt = <2000000>;
+ };
+
+ vreg_s6a_0p9: smps6 {
+ regulator-name = "vreg_s6a_0p9";
+ regulator-min-microvolt = <920000>;
+ regulator-max-microvolt = <1128000>;
+ };
+
+ vreg_s7a_1p2: smps7 {
+ regulator-name = "vreg_s7a_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ vreg_s8a_1p3: smps8 {
+ regulator-name = "vreg_s8a_1p3";
+ regulator-min-microvolt = <1352000>;
+ regulator-max-microvolt = <1352000>;
+ };
+
+ vreg_l1a_0p91: ldo1 {
+ regulator-name = "vreg_l1a_0p91";
+ regulator-min-microvolt = <312000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l2a_2p3: ldo2 {
+ regulator-name = "vreg_l2a_2p3";
+ regulator-min-microvolt = <2970000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l3a_1p2: ldo3 {
+ regulator-name = "vreg_l3a_1p2";
+ regulator-min-microvolt = <920000>;
+ regulator-max-microvolt = <1260000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l5a_0p8: ldo5 {
+ regulator-name = "vreg_l5a_0p8";
+ regulator-min-microvolt = <312000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l6a_0p91: ldo6 {
+ regulator-name = "vreg_l6a_0p91";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <950000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l7a_1p8: ldo7 {
+ regulator-name = "vreg_l7a_1p8";
+ regulator-min-microvolt = <1650000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+
+ };
+
+ vreg_l8a_0p91: ldo8 {
+ regulator-name = "vreg_l8a_0p91";
+ regulator-min-microvolt = <888000>;
+ regulator-max-microvolt = <925000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l9a_0p91: ldo9 {
+ regulator-name = "vreg_l9a_0p91";
+ regulator-min-microvolt = <312000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l10a_2p95: ldo10 {
+ regulator-name = "vreg_l10a_2p95";
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3544000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l11a_0p91: ldo11 {
+ regulator-name = "vreg_l11a_0p91";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l12a_1p8: ldo12 {
+ regulator-name = "vreg_l12a_1p8";
+ regulator-min-microvolt = <1504000>;
+ regulator-max-microvolt = <1504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l14a_1p8: ldo14 {
+ regulator-name = "vreg_l14a_1p8";
+ regulator-min-microvolt = <1650000>;
+ regulator-max-microvolt = <1950000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l15a_1p8: ldo15 {
+ regulator-name = "vreg_l15a_1p8";
+ regulator-min-microvolt = <1504000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l16a_1p8: ldo16 {
+ regulator-name = "vreg_l16a_1p8";
+ regulator-min-microvolt = <1710000>;
+ regulator-max-microvolt = <1890000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l17a_3p3: ldo17 {
+ regulator-name = "vreg_l17a_3p3";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3544000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l18a_1p2: ldo18 {
+ regulator-name = "vreg_l18a_1p2";
+ regulator-min-microvolt = <312000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+ };
+};
+
+&qup_i2c1_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_i2c2_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_i2c3_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_i2c4_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_i2c5_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_i2c6_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_i2c9_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_i2c10_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_i2c11_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_i2c12_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_i2c13_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_i2c14_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_i2c15_data_clk {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_spi1_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi1_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi2_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi2_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi3_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi3_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi4_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi4_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi5_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi5_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi6_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi6_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi9_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi9_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi10_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi10_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi11_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi11_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi12_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi12_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi13_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi13_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi14_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi14_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi15_cs {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_spi15_data_clk {
+ drive-strength = <6>;
+ bias-disable;
+};
+
+&qup_uart7_rx {
+ drive-strength = <2>;
+ bias-disable;
+};
+
+&qup_uart7_tx {
+ drive-strength = <2>;
+ bias-disable;
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&uart7 {
+ status = "okay";
+};
--
2.38.1
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH v5 1/2] arm64: dts: qcom: Add base QDU1000/QRU1000 DTSIs
2022-12-16 23:27 ` [PATCH v5 1/2] arm64: dts: qcom: Add base QDU1000/QRU1000 DTSIs Melody Olvera
@ 2022-12-17 14:59 ` Konrad Dybcio
2022-12-20 18:56 ` Melody Olvera
0 siblings, 1 reply; 5+ messages in thread
From: Konrad Dybcio @ 2022-12-17 14:59 UTC (permalink / raw)
To: Melody Olvera, Andy Gross, Bjorn Andersson, Rob Herring,
Krzysztof Kozlowski
Cc: linux-arm-msm, devicetree, linux-kernel
On 17.12.2022 00:27, Melody Olvera wrote:
> Add the base DTSI files for QDU1000 and QRU1000 SoCs, including base
> descriptions of CPUs, GCC, RPMHCC, QUP, TLMM, and interrupt-controller
> to boot to shell with console on these SoCs.
>
> Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>
> ---
> arch/arm64/boot/dts/qcom/qdu1000.dtsi | 1334 +++++++++++++++++++++++++
> arch/arm64/boot/dts/qcom/qru1000.dtsi | 26 +
> 2 files changed, 1360 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/qdu1000.dtsi
> create mode 100644 arch/arm64/boot/dts/qcom/qru1000.dtsi
>
> diff --git a/arch/arm64/boot/dts/qcom/qdu1000.dtsi b/arch/arm64/boot/dts/qcom/qdu1000.dtsi
> new file mode 100644
> index 000000000000..244007a488a3
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/qdu1000.dtsi
> @@ -0,0 +1,1334 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved.
> + */
> +
> +#include <dt-bindings/clock/qcom,qdu1000-gcc.h>
> +#include <dt-bindings/clock/qcom,rpmh.h>
> +#include <dt-bindings/dma/qcom-gpi.h>
> +#include <dt-bindings/interconnect/qcom,qdu1000-rpmh.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/power/qcom-rpmpd.h>
> +#include <dt-bindings/soc/qcom,rpmh-rsc.h>
> +
> +/ {
> + interrupt-parent = <&intc>;
> +
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + chosen: chosen { };
> +
> + cpus {
> + #address-cells = <2>;
> + #size-cells = <0>;
> +
> + CPU0: cpu@0 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55";
> + reg = <0x0 0x0>;
> + enable-method = "psci";
> + power-domain-names = "psci";
> + power-domains = <&CPU_PD0>;
> + qcom,freq-domains = <&cpufreq_hw 0>;
> + next-level-cache = <&L2_0>;
> + L2_0: l2-cache {
> + compatible = "cache";
> + next-level-cache = <&L3_0>;
> + L3_0: l3-cache {
> + compatible = "cache";
> + };
> + };
> + };
> +
> + CPU1: cpu@100 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55";
> + reg = <0x0 0x100>;
> + enable-method = "psci";
> + power-domains = <&CPU_PD1>;
> + power-domain-names = "psci";
> + qcom,freq-domains = <&cpufreq_hw 0>;
> + next-level-cache = <&L2_100>;
> + L2_100: l2-cache {
> + compatible = "cache";
> + next-level-cache = <&L3_0>;
> + };
> + };
> +
> + CPU2: cpu@200 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55";
> + reg = <0x0 0x200>;
> + enable-method = "psci";
> + power-domains = <&CPU_PD2>;
> + power-domain-names = "psci";
> + qcom,freq-domains = <&cpufreq_hw 0>;
> + next-level-cache = <&L2_200>;
> + L2_200: l2-cache {
> + compatible = "cache";
> + next-level-cache = <&L3_0>;
> + };
> + };
> +
> + CPU3: cpu@300 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55";
> + reg = <0x0 0x300>;
> + enable-method = "psci";
> + power-domains = <&CPU_PD3>;
> + power-domain-names = "psci";
> + qcom,freq-domains = <&cpufreq_hw 0>;
> + next-level-cache = <&L2_300>;
> + L2_300: l2-cache {
> + compatible = "cache";
> + next-level-cache = <&L3_0>;
> + };
> + };
> +
> + cpu-map {
> + cluster0 {
> + core0 {
> + cpu = <&CPU0>;
> + };
> +
> + core1 {
> + cpu = <&CPU1>;
> + };
> +
> + core2 {
> + cpu = <&CPU2>;
> + };
> +
> + core3 {
> + cpu = <&CPU3>;
> + };
> + };
> + };
> + };
> +
> + idle-states {
> + entry-method = "psci";
> +
> + CPU_OFF: cpu-sleep-0 {
> + compatible = "arm,idle-state";
> + entry-latency-us = <274>;
> + exit-latency-us = <480>;
> + min-residency-us = <3934>;
> + arm,psci-suspend-param = <0x40000004>;
> + local-timer-stop;
> + };
> + };
> +
> + domain-idle-states {
> + CLUSTER_SLEEP_0: cluster-sleep-0 {
> + compatible = "domain-idle-state";
> + entry-latency-us = <584>;
> + exit-latency-us = <2332>;
> + min-residency-us = <6118>;
> + arm,psci-suspend-param = <0x41000044>;
> + };
> +
> + CLUSTER_SLEEP_1: cluster-sleep-1 {
> + compatible = "domain-idle-state";
> + entry-latency-us = <2893>;
> + exit-latency-us = <4023>;
> + min-residency-us = <9987>;
> + arm,psci-suspend-param = <0x41003344>;
> + };
> + };
> +
> + firmware {
> + scm {
> + compatible = "qcom,scm-qdu1000", "qcom,scm";
> + };
> + };
> +
> + mc_virt: interconnect-0 {
> + compatible = "qcom,qdu1000-mc-virt";
> + #interconnect-cells = <2>;
> + qcom,bcm-voters = <&apps_bcm_voter>;
> + };
> +
> + clk_virt: interconnect-1 {
> + compatible = "qcom,qdu1000-clk-virt";
> + #interconnect-cells = <2>;
> + qcom,bcm-voters = <&apps_bcm_voter>;
> + };
> +
> + memory@80000000 {
> + device_type = "memory";
> + /* We expect the bootloader to fill in the size */
> + reg = <0x0 0x80000000 0x0 0x0>;
I'd appreciate others' input on this, but I think using 0x0 instead
of just 0 for parts that are ireelevant to us (e.g. addresses and
sizes below 4GiB) makes things more concise..
> + };
> +
> + pmu {
> + compatible = "arm,armv8-pmuv3";
> + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + psci {
> + compatible = "arm,psci-1.0";
> + method = "smc";
> +
> + CPU_PD0: power-domain-cpu0 {
> + #power-domain-cells = <0>;
> + power-domains = <&CLUSTER_PD>;
> + domain-idle-states = <&CPU_OFF>;
> + };
> +
> + CPU_PD1: power-domain-cpu1 {
> + #power-domain-cells = <0>;
> + power-domains = <&CLUSTER_PD>;
> + domain-idle-states = <&CPU_OFF>;
> + };
> +
> + CPU_PD2: power-domain-cpu2 {
> + #power-domain-cells = <0>;
> + power-domains = <&CLUSTER_PD>;
> + domain-idle-states = <&CPU_OFF>;
> + };
> +
> + CPU_PD3: power-domain-cpu3 {
> + #power-domain-cells = <0>;
> + power-domains = <&CLUSTER_PD>;
> + domain-idle-states = <&CPU_OFF>;
> + };
> +
> + CLUSTER_PD: power-domain-cluster {
> + #power-domain-cells = <0>;
> + domain-idle-states = <&CLUSTER_SLEEP_0 &CLUSTER_SLEEP_1>;
> + };
> + };
> +
> + reserved_memory: reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + hyp_mem: hyp@80000000 {
> + reg = <0x0 0x80000000 0x0 0x600000>;
> + no-map;
> + };
> +
> + xbl_dt_log_mem: xbl-dt-log@80600000 {
> + reg = <0x0 0x80600000 0x0 0x40000>;
> + no-map;
> + };
> +
> + xbl_ramdump_mem: xbl-ramdump@80640000 {
> + reg = <0x0 0x80640000 0x0 0x1c0000>;
> + no-map;
> + };
> +
> + aop_image_mem: aop-image@80800000 {
> + reg = <0x0 0x80800000 0x0 0x60000>;
> + no-map;
> + };
> +
> + aop_cmd_db_mem: aop-cmd-db@80860000 {
> + compatible = "qcom,cmd-db";
> + reg = <0x0 0x80860000 0x0 0x20000>;
> + no-map;
> + };
> +
> + aop_config_mem: aop-config@80880000 {
> + reg = <0x0 0x80880000 0x0 0x20000>;
> + no-map;
> + };
> +
> + tme_crash_dump_mem: tme-crash-dump@808a0000 {
> + reg = <0x0 0x808a0000 0x0 0x40000>;
> + no-map;
> + };
> +
> + tme_log_mem: tme-log@808e0000 {
> + reg = <0x0 0x808e0000 0x0 0x4000>;
> + no-map;
> + };
> +
> + uefi_log_mem: uefi-log@808e4000 {
> + reg = <0x0 0x808e4000 0x0 0x10000>;
> + no-map;
> + };
> +
> + /* secdata region can be reused by apps */
I think these comments are irrelevant, as the regions referenced
in them are simply not defined as reserved and they would matter
more for XBL developers.
> +
> + smem_mem: smem@80900000 {
> + compatible = "qcom,smem";
> + reg = <0x0 0x80900000 0x0 0x200000>;
> + no-map;
> + hwlocks = <&tcsr_mutex 3>;
> + };
> +
> + cpucp_fw_mem: cpucp-fw@80b00000 {
> + reg = <0x0 0x80b00000 0x0 0x100000>;
> + no-map;
> + };
> +
> + xbl_sc_mem: memory@80c00000 {
> + reg = <0x0 0x80c00000 0x0 0x40000>;
> + no-map;
> + };
> +
> + /* uefi region can be reused by apps */
> +
> + tz_stat_mem: tz-stat@81d00000 {
> + reg = <0x0 0x81d00000 0x0 0x100000>;
> + no-map;
> + };
> +
> + tags_mem: tags@81e00000 {
> + reg = <0x0 0x81e00000 0x0 0x500000>;
> + no-map;
> + };
> +
> + qtee_mem: qtee@82300000 {
> + reg = <0x0 0x82300000 0x0 0x500000>;
> + no-map;
> + };
> +
> + ta_mem: ta@82800000 {
> + reg = <0x0 0x82800000 0x0 0xa00000>;
> + no-map;
> + };
> +
> + fs1_mem: fs1@83200000 {
> + reg = <0x0 0x83200000 0x0 0x400000>;
> + no-map;
> + };
> +
> + fs2_mem: fs2@83600000 {
> + reg = <0x0 0x83600000 0x0 0x400000>;
> + no-map;
> + };
> +
> + fs3_mem: fs3@83a00000 {
> + reg = <0x0 0x83a00000 0x0 0x400000>;
> + no-map;
> + };
> +
> + /* Linux kernel image is loaded at 0x83e00000 */
> +
> + ipa_fw_mem: ipa-fw@8be00000 {
> + reg = <0x0 0x8be00000 0x0 0x10000>;
> + no-map;
> + };
> +
> + ipa_gsi_mem: ipa-gsi@8be10000 {
> + reg = <0x0 0x8be10000 0x0 0x14000>;
> + no-map;
> + };
> +
> + mpss_mem: mpss@8c000000 {
> + reg = <0x0 0x8c000000 0x0 0x12c00000>;
> + no-map;
> + };
> +
> + q6_mpss_dtb_mem: q6-mpss-dtb@9ec00000 {
> + reg = <0x0 0x9ec00000 0x0 0x80000>;
> + no-map;
> + };
> +
> + tenx_mem: tenx@a0000000 {
> + reg = <0x0 0xa0000000 0x0 0x19600000>;
> + no-map;
> + };
> +
> + oem_tenx_mem: oem-tenx@b9600000 {
> + reg = <0x0 0xb9600000 0x0 0x6a00000>;
> + no-map;
> + };
> +
> + tenx_q6_buffer_mem: tenx-q6-buffer@c0000000 {
> + reg = <0x0 0xc0000000 0x0 0x3200000>;
> + no-map;
> + };
> +
> + ipa_buffer_mem: ipa-buffer@c3200000 {
> + reg = <0x0 0xc3200000 0x0 0x12c00000>;
> + no-map;
> + };
> + };
> +
> + soc: soc@0 {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges = <0 0 0 0 0x10 0>;
> + dma-ranges = <0 0 0 0 0x10 0>;
> + compatible = "simple-bus";
The compatible should go fist.
> +
> + gcc: clock-controller@80000 {
> + compatible = "qcom,qdu1000-gcc";
> + reg = <0x0 0x80000 0x0 0x1f4200>;
> + clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>, <0>, <0>, <0>;
Please turn this into a vertical list:
clocks = <a>,
<b>,
etc.
> + #clock-cells = <1>;
> + #reset-cells = <1>;
> + #power-domain-cells = <1>;
> + };
> +
> + gpi_dma0: dma-controller@900000 {
> + compatible = "qcom,qdu1000-gpi-dma", "qcom,sm6350-gpi-dma";
> + reg = <0x0 0x900000 0x0 0x60000>;
> + interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
> + dma-channels = <12>;
> + dma-channel-mask = <0x3f>;
> + iommus = <&apps_smmu 0xf6 0x0>;
> + #dma-cells = <3>;
> + };
> +
> + qupv3_id_0: geniqup@9c0000 {
> + compatible = "qcom,geni-se-qup";
> + reg = <0x0 0x9c0000 0x0 0x2000>;
> + clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
> + <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
> + clock-names = "m-ahb", "s-ahb";
> + iommus = <&apps_smmu 0xe3 0x0>;
> + interconnects = <&clk_virt MASTER_QUP_CORE_0 0
> + &clk_virt SLAVE_QUP_CORE_0 0>;
> + interconnect-names = "qup-core";
> +
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> + status = "disabled";
> +
> + uart0: serial@980000 {
> + compatible = "qcom,geni-uart";
> + reg = <0x0 0x980000 0x0 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
Please keep XYZ-names after XYZ.
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_uart0_default>;
> + interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c1: i2c@984000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x0 0x984000 0x0 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
> + interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_i2c1_data_clk>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi1: spi@984000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x0 0x984000 0x0 0x4000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_spi1_data_clk>, <&qup_spi1_cs>;
> + status = "disabled";
> + };
> +
> + i2c2: i2c@988000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x0 0x988000 0x0 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
> + interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_i2c2_data_clk>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi2: spi@988000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x0 0x988000 0x0 0x4000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_spi2_data_clk>, <&qup_spi2_cs>;
> + status = "disabled";
> + };
> +
> + i2c3: i2c@98c000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x0 0x98c000 0x0 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
> + interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_i2c3_data_clk>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi3: spi@98c000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x0 0x98c000 0x0 0x4000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_spi3_data_clk>, <&qup_spi3_cs>;
> + status = "disabled";
> + };
> +
> + i2c4: i2c@990000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x0 0x990000 0x0 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
> + interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_i2c4_data_clk>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi4: spi@990000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x0 0x990000 0x0 0x4000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_spi4_data_clk>, <&qup_spi4_cs>;
> + status = "disabled";
> + };
> +
> + i2c5: i2c@994000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x0 0x994000 0x0 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
> + interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_i2c5_data_clk>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi5: spi@994000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x0 0x994000 0x0 0x4000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_spi5_data_clk>, <&qup_spi5_cs>;
> + status = "disabled";
> + };
> +
> + i2c6: i2c@998000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x0 0x998000 0x0 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
> + interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_i2c6_data_clk>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi6: spi@998000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x0 0x998000 0x0 0x4000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_spi6_data_clk>, <&qup_spi6_cs>;
> + status = "disabled";
> + };
> +
> + uart7: serial@99c000 {
> + compatible = "qcom,geni-debug-uart";
> + reg = <0x0 0x99c000 0x0 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_uart7_tx>, <&qup_uart7_rx>;
> + interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> + };
> +
> + gpi_dma1: dma-controller@a00000 {
> + compatible = "qcom,qdu1000-gpi-dma", "qcom,sm6350-gpi-dma";
> + reg = <0x0 0xa00000 0x0 0x60000>;
> + interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>;
> + dma-channels = <12>;
> + dma-channel-mask = <0x3f>;
> + iommus = <&apps_smmu 0x116 0x0>;
> + #dma-cells = <3>;
> + };
> +
> + qupv3_id_1: geniqup@ac0000 {
> + compatible = "qcom,geni-se-qup";
> + reg = <0x0 0xac0000 0x0 0x2000>;
> + clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
> + <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
> + clock-names = "m-ahb", "s-ahb";
> + iommus = <&apps_smmu 0x103 0x0>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + ranges;
Please remove the newline above `ranges;`.
> + status = "disabled";
> +
> + uart8: serial@a80000 {
> + compatible = "qcom,geni-uart";
> + reg = <0x0 0xa80000 0x0 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_uart8_default>;
> + interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c9: i2c@a84000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x0 0xa84000 0x0 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
> + interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_i2c9_data_clk>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi9: spi@a84000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x0 0xa84000 0x0 0x4000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_spi9_data_clk>, <&qup_spi9_cs>;
> + status = "disabled";
> + };
> +
> + i2c10: i2c@a88000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x0 0xa88000 0x0 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
> + interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_i2c10_data_clk>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi10: spi@a88000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x0 0xa88000 0x0 0x4000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs>;
> + status = "disabled";
> + };
> +
> + i2c11: i2c@a8c000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x0 0xa8c000 0x0 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
> + interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_i2c11_data_clk>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi11: spi@a8c000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x0 0xa8c000 0x0 0x4000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_spi11_data_clk>, <&qup_spi11_cs>;
> + status = "disabled";
> + };
> +
> + i2c12: i2c@a90000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x0 0xa90000 0x0 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
> + interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_i2c12_data_clk>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi12: spi@a90000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x0 0xa90000 0x0 0x4000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_spi12_data_clk>, <&qup_spi12_cs>;
> + status = "disabled";
> + };
> +
> + i2c13: i2c@a94000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x0 0xa94000 0x0 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
> + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_i2c13_data_clk>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + uart13: serial@a94000 {
> + compatible = "qcom,geni-uart";
> + reg = <0x0 0xa94000 0x0 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_uart13_default>;
> + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi13: spi@a94000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x0 0xa94000 0x0 0x4000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_spi13_data_clk>, <&qup_spi13_cs>;
> + status = "disabled";
> + };
> +
> + i2c14: i2c@a98000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x0 0xa98000 0x0 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
> + interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_i2c14_data_clk>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi14: spi@a98000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x0 0xa98000 0x0 0x4000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_spi14_data_clk>, <&qup_spi14_cs>;
> + status = "disabled";
> + };
> +
> + i2c15: i2c@a9c000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0x0 0xa9c000 0x0 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
> + interrupts = <GIC_SPI 365 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-0 = <&qup_i2c15_data_clk>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + spi15: spi@a9c000 {
> + compatible = "qcom,geni-spi";
> + reg = <0x0 0xa9c000 0x0 0x4000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interrupts = <GIC_SPI 365 IRQ_TYPE_LEVEL_HIGH>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_spi15_data_clk>, <&qup_spi15_cs>;
> + status = "disabled";
> + };
> + };
> +
> + system_noc: interconnect@1640000 {
> + compatible = "qcom,qdu1000-system-noc";
> + reg = <0x0 0x1640000 0x0 0x45080>;
> + #interconnect-cells = <2>;
> + qcom,bcm-voters = <&apps_bcm_voter>;
> + };
> +
> + tcsr_mutex: hwlock@1f40000 {
> + compatible = "qcom,tcsr-mutex";
> + reg = <0x0 0x1f40000 0x0 0x20000>;
> + #hwlock-cells = <1>;
> + };
> +
> + pdc: interrupt-controller@b220000 {
> + compatible = "qcom,qdu1000-pdc", "qcom,pdc";
> + reg = <0x0 0xb220000 0x0 0x30000>, <0x0 0x174000f0 0x0 0x64>;
> + qcom,pdc-ranges = <0 480 12>, <14 494 24>, <40 520 54>,
> + <94 609 31>, <125 63 1>;
> + #interrupt-cells = <2>;
> + interrupt-parent = <&intc>;
> + interrupt-controller;
> + };
> +
> + spmi_bus: spmi@c400000 {
> + compatible = "qcom,spmi-pmic-arb";
> + reg = <0x0 0xc400000 0x0 0x3000>,
> + <0x0 0xc500000 0x0 0x400000>,
> + <0x0 0xc440000 0x0 0x80000>,
> + <0x0 0xc4c0000 0x0 0x10000>,
> + <0x0 0xc42d000 0x0 0x4000>;
> + reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
> + interrupt-names = "periph_irq";
> + interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
> + qcom,ee = <0>;
> + qcom,channel = <0>;
> + #address-cells = <2>;
> + #size-cells = <0>;
> + interrupt-controller;
> + #interrupt-cells = <4>;
> + };
> +
> + tlmm: pinctrl@f000000 {
> + compatible = "qcom,qdu1000-tlmm";
> + reg = <0x0 0xf000000 0x0 0x1000000>;
> + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + gpio-ranges = <&tlmm 0 0 151>;
> + wakeup-parent = <&pdc>;
> +
> + qup_uart0_default: qup-uart0-default-state {
> + pins = "gpio6", "gpio7", "gpio8", "gpio9";
> + function = "qup00";
> + };
> +
> + qup_i2c1_data_clk: qup-i2c1-data-clk-state {
> + pins = "gpio10", "gpio11";
> + function = "qup01";
> + };
> +
> + qup_spi1_data_clk: qup-spi1-data-clk-state {
> + pins = "gpio10", "gpio11", "gpio12";
> + function = "qup01";
> + };
> +
> + qup_spi1_cs: qup-spi1-cs-state {
> + pins = "gpio13";
> + function = "gpio";
> + };
> +
> + qup_i2c2_data_clk: qup-i2c2-data-clk-state {
> + pins = "gpio12", "gpio13";
> + function = "qup02";
> + };
> +
> + qup_spi2_data_clk: qup-spi2-data-clk-state {
> + pins = "gpio12", "gpio13", "gpio10";
> + function = "qup02";
> + };
> +
> + qup_spi2_cs: qup-spi2-cs-state {
> + pins = "gpio11";
> + function = "gpio";
> + };
> +
> + qup_i2c3_data_clk: qup-i2c3-data-clk-state {
> + pins = "gpio14", "gpio15";
> + function = "qup03";
> + };
> +
> + qup_spi3_data_clk: qup-spi3-data-clk-state {
> + pins = "gpio14", "gpio15", "gpio16";
> + function = "qup03";
> + };
> +
> + qup_spi3_cs: qup-spi3-cs-state {
> + pins = "gpio17";
> + function = "gpio";
> + };
> +
> + qup_i2c4_data_clk: qup-i2c4-data-clk-state {
> + pins = "gpio16", "gpio17";
> + function = "qup04";
> + };
> +
> + qup_spi4_data_clk: qup-spi4-data-clk-state {
> + pins = "gpio16", "gpio17", "gpio14";
> + function = "qup04";
> + };
> +
> + qup_spi4_cs: qup-spi4-cs-state {
> + pins = "gpio15";
> + function = "gpio";
> + };
> +
> + qup_i2c5_data_clk: qup-i2c5-data-clk-state {
> + pins = "gpio130", "gpio131";
> + function = "qup05";
> + };
> +
> + qup_spi5_data_clk: qup-spi5-data-clk-state {
> + pins = "gpio130", "gpio131", "gpio132";
> + function = "qup05";
> + };
> +
> + qup_spi5_cs: qup-spi5-cs-state {
> + pins = "gpio133";
> + function = "gpio";
> + };
> +
> + qup_i2c6_data_clk: qup-i2c6-data-clk-state {
> + pins = "gpio132", "gpio133";
> + function = "qup06";
> + };
> +
> + qup_spi6_data_clk: qup-spi6-data-clk-state {
> + pins = "gpio132", "gpio133", "gpio130";
> + function = "qup06";
> + };
> +
> + qup_spi6_cs: qup-spi6-cs-state {
> + pins = "gpio131";
> + function = "gpio";
> + };
> +
> + qup_uart7_rx: qup-uart7-rx-state {
> + pins = "gpio135";
> + function = "qup07";
> + };
> +
> + qup_uart7_tx: qup-uart7-tx-state {
> + pins = "gpio134";
> + function = "qup07";
> + };
> +
> + qup_uart8_default: qup-uart8-default-state {
> + pins = "gpio18", "gpio19", "gpio20", "gpio21";
> + function = "qup10";
> + };
> +
> + qup_i2c9_data_clk: qup-i2c9-data-clk-state {
> + pins = "gpio22", "gpio23";
> + function = "qup11";
> + };
> +
> + qup_spi9_data_clk: qup-spi9-data-clk-state {
> + pins = "gpio22", "gpio23", "gpio24";
> + function = "qup11";
> + };
> +
> + qup_spi9_cs: qup-spi9-cs-state {
> + pins = "gpio25";
> + function = "gpio";
> + };
> +
> + qup_i2c10_data_clk: qup-i2c10-data-clk-state {
> + pins = "gpio24", "gpio25";
> + function = "qup12";
> + };
> +
> + qup_spi10_data_clk: qup-spi10-data-clk-state {
> + pins = "gpio24", "gpio25", "gpio22";
> + function = "qup12";
> + };
> +
> + qup_spi10_cs: qup-spi10-cs-state {
> + pins = "gpio23";
> + function = "gpio";
> + };
> +
> + qup_i2c11_data_clk: qup-i2c11-data-clk-state {
> + pins = "gpio26", "gpio27";
> + function = "qup13";
> + };
> +
> + qup_spi11_data_clk: qup-spi11-data-clk-state {
> + pins = "gpio26", "gpio27", "gpio28";
> + function = "qup13";
> + };
> +
> + qup_spi11_cs: qup-spi11-cs-state {
> + pins = "gpio29";
> + function = "gpio";
> + };
> +
> + qup_i2c12_data_clk: qup-i2c12-data-clk-state {
> + pins = "gpio28", "gpio29";
> + function = "qup14";
> + };
> +
> + qup_spi12_data_clk: qup-spi12-data-clk-state {
> + pins = "gpio28", "gpio29", "gpio26";
> + function = "qup14";
> + };
> +
> + qup_spi12_cs: qup-spi12-cs-state {
> + pins = "gpio27";
> + function = "gpio";
> + };
> +
> + qup_i2c13_data_clk: qup-i2c13-data-clk-state {
> + pins = "gpio30", "gpio31";
> + function = "qup15";
> + };
> +
> + qup_spi13_data_clk: qup-spi13-data-clk-state {
> + pins = "gpio30", "gpio31", "gpio32";
> + function = "qup15";
> + };
> +
> + qup_spi13_cs: qup-spi13-cs-state {
> + pins = "gpio33";
> + function = "gpio";
> + };
> +
> + qup_uart13_default: qup-uart13-default-state {
> + pins = "gpio30", "gpio31", "gpio32", "gpio33";
> + function = "qup15";
> + };
> +
> + qup_i2c14_data_clk: qup-i2c14-data-clk-state {
> + pins = "gpio34", "gpio35";
> + function = "qup16";
> + };
> +
> + qup_spi14_data_clk: qup-spi14-data-clk-state {
> + pins = "gpio34", "gpio35", "gpio36";
> + function = "qup16";
> + };
> +
> + qup_spi14_cs: qup-spi14-cs-state {
> + pins = "gpio37", "gpio38";
> + function = "gpio";
> + };
> +
> + qup_i2c15_data_clk: qup-i2c15-data-clk-state {
> + pins = "gpio40", "gpio41";
> + function = "qup17";
> + };
> +
> + qup_spi15_data_clk: qup-spi15-data-clk-state {
> + pins = "gpio40", "gpio41", "gpio30";
> + function = "qup17";
> + };
> +
> + qup_spi15_cs: qup-spi15-cs-state {
> + pins = "gpio31";
> + function = "gpio";
> + };
> + };
> +
> + apps_smmu: iommu@15000000 {
> + compatible = "qcom,qdu1000-smmu-500", "arm,mmu-500";
> + reg = <0x0 0x15000000 0x0 0x100000>;
> + #iommu-cells = <2>;
> + #global-interrupts = <2>;
> + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
There should be a space, not a tab after the = sign.
> + <GIC_SPI 426 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 671 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 672 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + intc: interrupt-controller@17200000 {
> + compatible = "arm,gic-v3";
> + reg = <0x0 0x17200000 0x0 0x10000>, /* GICD */
> + <0x0 0x17260000 0x0 0x80000>; /* GICR * 4 */
> + #interrupt-cells = <3>;
> + interrupt-controller;
> + #redistributor-regions = <1>;
> + redistributor-stride = <0x0 0x20000>;
> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
Please move interrupts below reg.
> + };
> +
> + timer@17420000 {
> + compatible = "arm,armv7-timer-mem";
> + reg = <0x0 0x17420000 0x0 0x1000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + frame@17421000 {
> + reg = <0x17421000 0x1000>,
> + <0x17422000 0x1000>;
> + frame-number = <0>;
> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
Please move interrupts above frame-number.
> + };
> +
> + frame@17423000 {
> + reg = <0x17423000 0x1000>;
> + frame-number = <1>;
> + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
> + status = "disabled";
> + };
> +
> + frame@17425000 {
> + reg = <0x17425000 0x1000>,
> + <0x17426000 0x1000>;
> + frame-number = <2>;
> + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
> + status = "disabled";
> + };
> +
> + frame@17427000 {
> + reg = <0x17427000 0x1000>;
> + frame-number = <3>;
> + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
> + status = "disabled";
> + };
> +
> + frame@17429000 {
> + reg = <0x17429000 0x1000>;
> + frame-number = <4>;
> + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> + status = "disabled";
> + };
> +
> + frame@1742b000 {
> + reg = <0x1742b000 0x1000>;
> + frame-number = <5>;
> + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> + status = "disabled";
> + };
> +
> + frame@1742d000 {
> + reg = <0x1742d000 0x1000>;
> + frame-number = <6>;
> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> + status = "disabled";
> + };
> + };
> +
> + apps_rsc: rsc@17a00000 {
> + compatible = "qcom,rpmh-rsc";
> + reg = <0x0 0x17a00000 0x0 0x10000>,
> + <0x0 0x17a10000 0x0 0x10000>,
> + <0x0 0x17a20000 0x0 0x10000>;
> + reg-names = "drv-0", "drv-1", "drv-2";
> + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> + qcom,tcs-offset = <0xd00>;
> + qcom,drv-id = <2>;
> + qcom,tcs-config = <ACTIVE_TCS 2>, <SLEEP_TCS 3>,
> + <WAKE_TCS 3>, <CONTROL_TCS 0>;
> + label = "apps_rsc";
> +
> + apps_bcm_voter: bcm-voter {
> + compatible = "qcom,bcm-voter";
> + };
> +
> + rpmhcc: clock-controller {
> + compatible = "qcom,qdu1000-rpmh-clk";
> + #clock-cells = <1>;
> + clock-names = "xo";
> + clocks = <&xo_board>;
Please keep XYZ-names after XYZ.
> + };
> +
> + rpmhpd: power-controller {
> + compatible = "qcom,qdu1000-rpmhpd";
> + #power-domain-cells = <1>;
> + operating-points-v2 = <&rpmhpd_opp_table>;
> +
> + rpmhpd_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + rpmhpd_opp_ret: opp1 {
> + opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
> + };
> +
> + rpmhpd_opp_min_svs: opp2 {
> + opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
> + };
> +
> + rpmhpd_opp_low_svs: opp3 {
> + opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
> + };
> +
> + rpmhpd_opp_svs: opp4 {
> + opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
> + };
> +
> + rpmhpd_opp_svs_l1: opp5 {
> + opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
> + };
> +
> + rpmhpd_opp_nom: opp6 {
> + opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
> + };
> +
> + rpmhpd_opp_nom_l1: opp7 {
> + opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
> + };
> +
> + rpmhpd_opp_nom_l2: opp8 {
> + opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
> + };
> +
> + rpmhpd_opp_turbo: opp9 {
> + opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
> + };
> +
> + rpmhpd_opp_turbo_l1: opp10 {
> + opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
> + };
> + };
> + };
> + };
> +
> + cpufreq_hw: cpufreq@17d90000 {
> + compatible = "qcom,qdu1000-cpufreq-epss", "qcom,cpufreq-epss";
> + reg = <0x0 0x17d90000 0x0 0x1000>, <0x0 0x17d91000 0x0 0x1000>;
> + reg-names = "freq-domain0", "freq-domain1";
> + clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>;
> + clock-names = "xo", "alternate";
> + #freq-domain-cells = <1>;
> + };
> +
> + gem_noc: interconnect@19100000 {
> + compatible = "qcom,qdu1000-gem-noc";
> + reg = <0x0 0x19100000 0x0 0xB8080>;
> + #interconnect-cells = <2>;
> + qcom,bcm-voters = <&apps_bcm_voter>;
It would be nice to keep #interconnect-cells last.
> + };
> + };
> +
> + arch_timer: timer {
> + compatible = "arm,armv8-timer";
> + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 12 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
> + clock-frequency = <19200000>;
Please remove this property, unless this platform is super
special and doesn't boot without it (otherwise CNTRFRQ_ELn
is almost surely initialized somewhere earlier in the boot
chain.
Konrad
> + };
> +};
> diff --git a/arch/arm64/boot/dts/qcom/qru1000.dtsi b/arch/arm64/boot/dts/qcom/qru1000.dtsi
> new file mode 100644
> index 000000000000..eac5dc54a8ab
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/qru1000.dtsi
> @@ -0,0 +1,26 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved.
> + */
> +
> +#include "qdu1000.dtsi"
> +/delete-node/ &tenx_mem;
> +/delete-node/ &oem_tenx_mem;
> +/delete-node/ &tenx_q6_buffer_mem;
> +
> +&reserved_memory {
> + oem_tenx_mem: oem-tenx@a0000000 {
> + reg = <0x0 0xa0000000 0x0 0x6400000>;
> + no-map;
> + };
> +
> + mpss_diag_buffer_mem: mpss-diag-buffer@aea00000 {
> + reg = <0x0 0xaea00000 0x0 0x6400000>;
> + no-map;
> + };
> +
> + tenx_q6_buffer_mem: tenx-q6-buffer@b4e00000 {
> + reg = <0x0 0xb4e00000 0x0 0x3200000>;
> + no-map;
> + };
> +};
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH v5 1/2] arm64: dts: qcom: Add base QDU1000/QRU1000 DTSIs
2022-12-17 14:59 ` Konrad Dybcio
@ 2022-12-20 18:56 ` Melody Olvera
0 siblings, 0 replies; 5+ messages in thread
From: Melody Olvera @ 2022-12-20 18:56 UTC (permalink / raw)
To: Konrad Dybcio, Andy Gross, Bjorn Andersson, Rob Herring,
Krzysztof Kozlowski
Cc: linux-arm-msm, devicetree, linux-kernel
On 12/17/2022 8:59 AM, Konrad Dybcio wrote:
>
> On 17.12.2022 00:27, Melody Olvera wrote:
>> Add the base DTSI files for QDU1000 and QRU1000 SoCs, including base
>> descriptions of CPUs, GCC, RPMHCC, QUP, TLMM, and interrupt-controller
>> to boot to shell with console on these SoCs.
>>
>> Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>
>> ---
>> arch/arm64/boot/dts/qcom/qdu1000.dtsi | 1334 +++++++++++++++++++++++++
>> arch/arm64/boot/dts/qcom/qru1000.dtsi | 26 +
>> 2 files changed, 1360 insertions(+)
>> create mode 100644 arch/arm64/boot/dts/qcom/qdu1000.dtsi
>> create mode 100644 arch/arm64/boot/dts/qcom/qru1000.dtsi
>>
>> diff --git a/arch/arm64/boot/dts/qcom/qdu1000.dtsi b/arch/arm64/boot/dts/qcom/qdu1000.dtsi
>> new file mode 100644
>> index 000000000000..244007a488a3
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/qcom/qdu1000.dtsi
>> @@ -0,0 +1,1334 @@
>> +// SPDX-License-Identifier: BSD-3-Clause
>> +/*
>> + * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved.
>> + */
>> +
>> +#include <dt-bindings/clock/qcom,qdu1000-gcc.h>
>> +#include <dt-bindings/clock/qcom,rpmh.h>
>> +#include <dt-bindings/dma/qcom-gpi.h>
>> +#include <dt-bindings/interconnect/qcom,qdu1000-rpmh.h>
>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> +#include <dt-bindings/power/qcom-rpmpd.h>
>> +#include <dt-bindings/soc/qcom,rpmh-rsc.h>
>> +
>> +/ {
>> + interrupt-parent = <&intc>;
>> +
>> + #address-cells = <2>;
>> + #size-cells = <2>;
>> +
>> + chosen: chosen { };
>> +
>> + cpus {
>> + #address-cells = <2>;
>> + #size-cells = <0>;
>> +
>> + CPU0: cpu@0 {
>> + device_type = "cpu";
>> + compatible = "arm,cortex-a55";
>> + reg = <0x0 0x0>;
>> + enable-method = "psci";
>> + power-domain-names = "psci";
>> + power-domains = <&CPU_PD0>;
>> + qcom,freq-domains = <&cpufreq_hw 0>;
>> + next-level-cache = <&L2_0>;
>> + L2_0: l2-cache {
>> + compatible = "cache";
>> + next-level-cache = <&L3_0>;
>> + L3_0: l3-cache {
>> + compatible = "cache";
>> + };
>> + };
>> + };
>> +
>> + CPU1: cpu@100 {
>> + device_type = "cpu";
>> + compatible = "arm,cortex-a55";
>> + reg = <0x0 0x100>;
>> + enable-method = "psci";
>> + power-domains = <&CPU_PD1>;
>> + power-domain-names = "psci";
>> + qcom,freq-domains = <&cpufreq_hw 0>;
>> + next-level-cache = <&L2_100>;
>> + L2_100: l2-cache {
>> + compatible = "cache";
>> + next-level-cache = <&L3_0>;
>> + };
>> + };
>> +
>> + CPU2: cpu@200 {
>> + device_type = "cpu";
>> + compatible = "arm,cortex-a55";
>> + reg = <0x0 0x200>;
>> + enable-method = "psci";
>> + power-domains = <&CPU_PD2>;
>> + power-domain-names = "psci";
>> + qcom,freq-domains = <&cpufreq_hw 0>;
>> + next-level-cache = <&L2_200>;
>> + L2_200: l2-cache {
>> + compatible = "cache";
>> + next-level-cache = <&L3_0>;
>> + };
>> + };
>> +
>> + CPU3: cpu@300 {
>> + device_type = "cpu";
>> + compatible = "arm,cortex-a55";
>> + reg = <0x0 0x300>;
>> + enable-method = "psci";
>> + power-domains = <&CPU_PD3>;
>> + power-domain-names = "psci";
>> + qcom,freq-domains = <&cpufreq_hw 0>;
>> + next-level-cache = <&L2_300>;
>> + L2_300: l2-cache {
>> + compatible = "cache";
>> + next-level-cache = <&L3_0>;
>> + };
>> + };
>> +
>> + cpu-map {
>> + cluster0 {
>> + core0 {
>> + cpu = <&CPU0>;
>> + };
>> +
>> + core1 {
>> + cpu = <&CPU1>;
>> + };
>> +
>> + core2 {
>> + cpu = <&CPU2>;
>> + };
>> +
>> + core3 {
>> + cpu = <&CPU3>;
>> + };
>> + };
>> + };
>> + };
>> +
>> + idle-states {
>> + entry-method = "psci";
>> +
>> + CPU_OFF: cpu-sleep-0 {
>> + compatible = "arm,idle-state";
>> + entry-latency-us = <274>;
>> + exit-latency-us = <480>;
>> + min-residency-us = <3934>;
>> + arm,psci-suspend-param = <0x40000004>;
>> + local-timer-stop;
>> + };
>> + };
>> +
>> + domain-idle-states {
>> + CLUSTER_SLEEP_0: cluster-sleep-0 {
>> + compatible = "domain-idle-state";
>> + entry-latency-us = <584>;
>> + exit-latency-us = <2332>;
>> + min-residency-us = <6118>;
>> + arm,psci-suspend-param = <0x41000044>;
>> + };
>> +
>> + CLUSTER_SLEEP_1: cluster-sleep-1 {
>> + compatible = "domain-idle-state";
>> + entry-latency-us = <2893>;
>> + exit-latency-us = <4023>;
>> + min-residency-us = <9987>;
>> + arm,psci-suspend-param = <0x41003344>;
>> + };
>> + };
>> +
>> + firmware {
>> + scm {
>> + compatible = "qcom,scm-qdu1000", "qcom,scm";
>> + };
>> + };
>> +
>> + mc_virt: interconnect-0 {
>> + compatible = "qcom,qdu1000-mc-virt";
>> + #interconnect-cells = <2>;
>> + qcom,bcm-voters = <&apps_bcm_voter>;
>> + };
>> +
>> + clk_virt: interconnect-1 {
>> + compatible = "qcom,qdu1000-clk-virt";
>> + #interconnect-cells = <2>;
>> + qcom,bcm-voters = <&apps_bcm_voter>;
>> + };
>> +
>> + memory@80000000 {
>> + device_type = "memory";
>> + /* We expect the bootloader to fill in the size */
>> + reg = <0x0 0x80000000 0x0 0x0>;
> I'd appreciate others' input on this, but I think using 0x0 instead
> of just 0 for parts that are ireelevant to us (e.g. addresses and
> sizes below 4GiB) makes things more concise..
>
>
>> + };
>> +
>> + pmu {
>> + compatible = "arm,armv8-pmuv3";
>> + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
>> + };
>> +
>> + psci {
>> + compatible = "arm,psci-1.0";
>> + method = "smc";
>> +
>> + CPU_PD0: power-domain-cpu0 {
>> + #power-domain-cells = <0>;
>> + power-domains = <&CLUSTER_PD>;
>> + domain-idle-states = <&CPU_OFF>;
>> + };
>> +
>> + CPU_PD1: power-domain-cpu1 {
>> + #power-domain-cells = <0>;
>> + power-domains = <&CLUSTER_PD>;
>> + domain-idle-states = <&CPU_OFF>;
>> + };
>> +
>> + CPU_PD2: power-domain-cpu2 {
>> + #power-domain-cells = <0>;
>> + power-domains = <&CLUSTER_PD>;
>> + domain-idle-states = <&CPU_OFF>;
>> + };
>> +
>> + CPU_PD3: power-domain-cpu3 {
>> + #power-domain-cells = <0>;
>> + power-domains = <&CLUSTER_PD>;
>> + domain-idle-states = <&CPU_OFF>;
>> + };
>> +
>> + CLUSTER_PD: power-domain-cluster {
>> + #power-domain-cells = <0>;
>> + domain-idle-states = <&CLUSTER_SLEEP_0 &CLUSTER_SLEEP_1>;
>> + };
>> + };
>> +
>> + reserved_memory: reserved-memory {
>> + #address-cells = <2>;
>> + #size-cells = <2>;
>> + ranges;
>> +
>> + hyp_mem: hyp@80000000 {
>> + reg = <0x0 0x80000000 0x0 0x600000>;
>> + no-map;
>> + };
>> +
>> + xbl_dt_log_mem: xbl-dt-log@80600000 {
>> + reg = <0x0 0x80600000 0x0 0x40000>;
>> + no-map;
>> + };
>> +
>> + xbl_ramdump_mem: xbl-ramdump@80640000 {
>> + reg = <0x0 0x80640000 0x0 0x1c0000>;
>> + no-map;
>> + };
>> +
>> + aop_image_mem: aop-image@80800000 {
>> + reg = <0x0 0x80800000 0x0 0x60000>;
>> + no-map;
>> + };
>> +
>> + aop_cmd_db_mem: aop-cmd-db@80860000 {
>> + compatible = "qcom,cmd-db";
>> + reg = <0x0 0x80860000 0x0 0x20000>;
>> + no-map;
>> + };
>> +
>> + aop_config_mem: aop-config@80880000 {
>> + reg = <0x0 0x80880000 0x0 0x20000>;
>> + no-map;
>> + };
>> +
>> + tme_crash_dump_mem: tme-crash-dump@808a0000 {
>> + reg = <0x0 0x808a0000 0x0 0x40000>;
>> + no-map;
>> + };
>> +
>> + tme_log_mem: tme-log@808e0000 {
>> + reg = <0x0 0x808e0000 0x0 0x4000>;
>> + no-map;
>> + };
>> +
>> + uefi_log_mem: uefi-log@808e4000 {
>> + reg = <0x0 0x808e4000 0x0 0x10000>;
>> + no-map;
>> + };
>> +
>> + /* secdata region can be reused by apps */
> I think these comments are irrelevant, as the regions referenced
> in them are simply not defined as reserved and they would matter
> more for XBL developers.
Fair enough; will remove.
>> +
>> + smem_mem: smem@80900000 {
>> + compatible = "qcom,smem";
>> + reg = <0x0 0x80900000 0x0 0x200000>;
>> + no-map;
>> + hwlocks = <&tcsr_mutex 3>;
>> + };
>> +
>> + cpucp_fw_mem: cpucp-fw@80b00000 {
>> + reg = <0x0 0x80b00000 0x0 0x100000>;
>> + no-map;
>> + };
>> +
>> + xbl_sc_mem: memory@80c00000 {
>> + reg = <0x0 0x80c00000 0x0 0x40000>;
>> + no-map;
>> + };
>> +
>> + /* uefi region can be reused by apps */
>> +
>> + tz_stat_mem: tz-stat@81d00000 {
>> + reg = <0x0 0x81d00000 0x0 0x100000>;
>> + no-map;
>> + };
>> +
>> + tags_mem: tags@81e00000 {
>> + reg = <0x0 0x81e00000 0x0 0x500000>;
>> + no-map;
>> + };
>> +
>> + qtee_mem: qtee@82300000 {
>> + reg = <0x0 0x82300000 0x0 0x500000>;
>> + no-map;
>> + };
>> +
>> + ta_mem: ta@82800000 {
>> + reg = <0x0 0x82800000 0x0 0xa00000>;
>> + no-map;
>> + };
>> +
>> + fs1_mem: fs1@83200000 {
>> + reg = <0x0 0x83200000 0x0 0x400000>;
>> + no-map;
>> + };
>> +
>> + fs2_mem: fs2@83600000 {
>> + reg = <0x0 0x83600000 0x0 0x400000>;
>> + no-map;
>> + };
>> +
>> + fs3_mem: fs3@83a00000 {
>> + reg = <0x0 0x83a00000 0x0 0x400000>;
>> + no-map;
>> + };
>> +
>> + /* Linux kernel image is loaded at 0x83e00000 */
>> +
>> + ipa_fw_mem: ipa-fw@8be00000 {
>> + reg = <0x0 0x8be00000 0x0 0x10000>;
>> + no-map;
>> + };
>> +
>> + ipa_gsi_mem: ipa-gsi@8be10000 {
>> + reg = <0x0 0x8be10000 0x0 0x14000>;
>> + no-map;
>> + };
>> +
>> + mpss_mem: mpss@8c000000 {
>> + reg = <0x0 0x8c000000 0x0 0x12c00000>;
>> + no-map;
>> + };
>> +
>> + q6_mpss_dtb_mem: q6-mpss-dtb@9ec00000 {
>> + reg = <0x0 0x9ec00000 0x0 0x80000>;
>> + no-map;
>> + };
>> +
>> + tenx_mem: tenx@a0000000 {
>> + reg = <0x0 0xa0000000 0x0 0x19600000>;
>> + no-map;
>> + };
>> +
>> + oem_tenx_mem: oem-tenx@b9600000 {
>> + reg = <0x0 0xb9600000 0x0 0x6a00000>;
>> + no-map;
>> + };
>> +
>> + tenx_q6_buffer_mem: tenx-q6-buffer@c0000000 {
>> + reg = <0x0 0xc0000000 0x0 0x3200000>;
>> + no-map;
>> + };
>> +
>> + ipa_buffer_mem: ipa-buffer@c3200000 {
>> + reg = <0x0 0xc3200000 0x0 0x12c00000>;
>> + no-map;
>> + };
>> + };
>> +
>> + soc: soc@0 {
>> + #address-cells = <2>;
>> + #size-cells = <2>;
>> + ranges = <0 0 0 0 0x10 0>;
>> + dma-ranges = <0 0 0 0 0x10 0>;
>> + compatible = "simple-bus";
> The compatible should go fist.
Got it; must've missed this.
>
>> +
>> + gcc: clock-controller@80000 {
>> + compatible = "qcom,qdu1000-gcc";
>> + reg = <0x0 0x80000 0x0 0x1f4200>;
>> + clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>, <0>, <0>, <0>;
> Please turn this into a vertical list:
>
> clocks = <a>,
> <b>,
>
> etc.
Sure thing.
>> + #clock-cells = <1>;
>> + #reset-cells = <1>;
>> + #power-domain-cells = <1>;
>> + };
>> +
>> + gpi_dma0: dma-controller@900000 {
>> + compatible = "qcom,qdu1000-gpi-dma", "qcom,sm6350-gpi-dma";
>> + reg = <0x0 0x900000 0x0 0x60000>;
>> + interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
>> + dma-channels = <12>;
>> + dma-channel-mask = <0x3f>;
>> + iommus = <&apps_smmu 0xf6 0x0>;
>> + #dma-cells = <3>;
>> + };
>> +
>> + qupv3_id_0: geniqup@9c0000 {
>> + compatible = "qcom,geni-se-qup";
>> + reg = <0x0 0x9c0000 0x0 0x2000>;
>> + clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
>> + <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
>> + clock-names = "m-ahb", "s-ahb";
>> + iommus = <&apps_smmu 0xe3 0x0>;
>> + interconnects = <&clk_virt MASTER_QUP_CORE_0 0
>> + &clk_virt SLAVE_QUP_CORE_0 0>;
>> + interconnect-names = "qup-core";
>> +
>> + #address-cells = <2>;
>> + #size-cells = <2>;
>> + ranges;
>> + status = "disabled";
>> +
>> + uart0: serial@980000 {
>> + compatible = "qcom,geni-uart";
>> + reg = <0x0 0x980000 0x0 0x4000>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
> Please keep XYZ-names after XYZ.
Will do.
>
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_uart0_default>;
>> + interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + i2c1: i2c@984000 {
>> + compatible = "qcom,geni-i2c";
>> + reg = <0x0 0x984000 0x0 0x4000>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
>> + interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_i2c1_data_clk>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + spi1: spi@984000 {
>> + compatible = "qcom,geni-spi";
>> + reg = <0x0 0x984000 0x0 0x4000>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_spi1_data_clk>, <&qup_spi1_cs>;
>> + status = "disabled";
>> + };
>> +
>> + i2c2: i2c@988000 {
>> + compatible = "qcom,geni-i2c";
>> + reg = <0x0 0x988000 0x0 0x4000>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
>> + interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_i2c2_data_clk>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + spi2: spi@988000 {
>> + compatible = "qcom,geni-spi";
>> + reg = <0x0 0x988000 0x0 0x4000>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_spi2_data_clk>, <&qup_spi2_cs>;
>> + status = "disabled";
>> + };
>> +
>> + i2c3: i2c@98c000 {
>> + compatible = "qcom,geni-i2c";
>> + reg = <0x0 0x98c000 0x0 0x4000>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
>> + interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_i2c3_data_clk>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + spi3: spi@98c000 {
>> + compatible = "qcom,geni-spi";
>> + reg = <0x0 0x98c000 0x0 0x4000>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_spi3_data_clk>, <&qup_spi3_cs>;
>> + status = "disabled";
>> + };
>> +
>> + i2c4: i2c@990000 {
>> + compatible = "qcom,geni-i2c";
>> + reg = <0x0 0x990000 0x0 0x4000>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
>> + interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_i2c4_data_clk>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + spi4: spi@990000 {
>> + compatible = "qcom,geni-spi";
>> + reg = <0x0 0x990000 0x0 0x4000>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_spi4_data_clk>, <&qup_spi4_cs>;
>> + status = "disabled";
>> + };
>> +
>> + i2c5: i2c@994000 {
>> + compatible = "qcom,geni-i2c";
>> + reg = <0x0 0x994000 0x0 0x4000>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
>> + interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_i2c5_data_clk>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + spi5: spi@994000 {
>> + compatible = "qcom,geni-spi";
>> + reg = <0x0 0x994000 0x0 0x4000>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_spi5_data_clk>, <&qup_spi5_cs>;
>> + status = "disabled";
>> + };
>> +
>> + i2c6: i2c@998000 {
>> + compatible = "qcom,geni-i2c";
>> + reg = <0x0 0x998000 0x0 0x4000>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
>> + interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_i2c6_data_clk>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + spi6: spi@998000 {
>> + compatible = "qcom,geni-spi";
>> + reg = <0x0 0x998000 0x0 0x4000>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_spi6_data_clk>, <&qup_spi6_cs>;
>> + status = "disabled";
>> + };
>> +
>> + uart7: serial@99c000 {
>> + compatible = "qcom,geni-debug-uart";
>> + reg = <0x0 0x99c000 0x0 0x4000>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_uart7_tx>, <&qup_uart7_rx>;
>> + interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + gpi_dma1: dma-controller@a00000 {
>> + compatible = "qcom,qdu1000-gpi-dma", "qcom,sm6350-gpi-dma";
>> + reg = <0x0 0xa00000 0x0 0x60000>;
>> + interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>;
>> + dma-channels = <12>;
>> + dma-channel-mask = <0x3f>;
>> + iommus = <&apps_smmu 0x116 0x0>;
>> + #dma-cells = <3>;
>> + };
>> +
>> + qupv3_id_1: geniqup@ac0000 {
>> + compatible = "qcom,geni-se-qup";
>> + reg = <0x0 0xac0000 0x0 0x2000>;
>> + clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
>> + <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
>> + clock-names = "m-ahb", "s-ahb";
>> + iommus = <&apps_smmu 0x103 0x0>;
>> + #address-cells = <2>;
>> + #size-cells = <2>;
>> +
>> + ranges;
> Please remove the newline above `ranges;`.
Ok.
>
>
>> + status = "disabled";
>> +
>> + uart8: serial@a80000 {
>> + compatible = "qcom,geni-uart";
>> + reg = <0x0 0xa80000 0x0 0x4000>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_uart8_default>;
>> + interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + i2c9: i2c@a84000 {
>> + compatible = "qcom,geni-i2c";
>> + reg = <0x0 0xa84000 0x0 0x4000>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
>> + interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_i2c9_data_clk>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + spi9: spi@a84000 {
>> + compatible = "qcom,geni-spi";
>> + reg = <0x0 0xa84000 0x0 0x4000>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_spi9_data_clk>, <&qup_spi9_cs>;
>> + status = "disabled";
>> + };
>> +
>> + i2c10: i2c@a88000 {
>> + compatible = "qcom,geni-i2c";
>> + reg = <0x0 0xa88000 0x0 0x4000>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
>> + interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_i2c10_data_clk>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + spi10: spi@a88000 {
>> + compatible = "qcom,geni-spi";
>> + reg = <0x0 0xa88000 0x0 0x4000>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs>;
>> + status = "disabled";
>> + };
>> +
>> + i2c11: i2c@a8c000 {
>> + compatible = "qcom,geni-i2c";
>> + reg = <0x0 0xa8c000 0x0 0x4000>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
>> + interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_i2c11_data_clk>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + spi11: spi@a8c000 {
>> + compatible = "qcom,geni-spi";
>> + reg = <0x0 0xa8c000 0x0 0x4000>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_spi11_data_clk>, <&qup_spi11_cs>;
>> + status = "disabled";
>> + };
>> +
>> + i2c12: i2c@a90000 {
>> + compatible = "qcom,geni-i2c";
>> + reg = <0x0 0xa90000 0x0 0x4000>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
>> + interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_i2c12_data_clk>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + spi12: spi@a90000 {
>> + compatible = "qcom,geni-spi";
>> + reg = <0x0 0xa90000 0x0 0x4000>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_spi12_data_clk>, <&qup_spi12_cs>;
>> + status = "disabled";
>> + };
>> +
>> + i2c13: i2c@a94000 {
>> + compatible = "qcom,geni-i2c";
>> + reg = <0x0 0xa94000 0x0 0x4000>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
>> + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_i2c13_data_clk>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + uart13: serial@a94000 {
>> + compatible = "qcom,geni-uart";
>> + reg = <0x0 0xa94000 0x0 0x4000>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_uart13_default>;
>> + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + spi13: spi@a94000 {
>> + compatible = "qcom,geni-spi";
>> + reg = <0x0 0xa94000 0x0 0x4000>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_spi13_data_clk>, <&qup_spi13_cs>;
>> + status = "disabled";
>> + };
>> +
>> + i2c14: i2c@a98000 {
>> + compatible = "qcom,geni-i2c";
>> + reg = <0x0 0xa98000 0x0 0x4000>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
>> + interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_i2c14_data_clk>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + spi14: spi@a98000 {
>> + compatible = "qcom,geni-spi";
>> + reg = <0x0 0xa98000 0x0 0x4000>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_spi14_data_clk>, <&qup_spi14_cs>;
>> + status = "disabled";
>> + };
>> +
>> + i2c15: i2c@a9c000 {
>> + compatible = "qcom,geni-i2c";
>> + reg = <0x0 0xa9c000 0x0 0x4000>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
>> + interrupts = <GIC_SPI 365 IRQ_TYPE_LEVEL_HIGH>;
>> + pinctrl-0 = <&qup_i2c15_data_clk>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + spi15: spi@a9c000 {
>> + compatible = "qcom,geni-spi";
>> + reg = <0x0 0xa9c000 0x0 0x4000>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + interrupts = <GIC_SPI 365 IRQ_TYPE_LEVEL_HIGH>;
>> + clock-names = "se";
>> + clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&qup_spi15_data_clk>, <&qup_spi15_cs>;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + system_noc: interconnect@1640000 {
>> + compatible = "qcom,qdu1000-system-noc";
>> + reg = <0x0 0x1640000 0x0 0x45080>;
>> + #interconnect-cells = <2>;
>> + qcom,bcm-voters = <&apps_bcm_voter>;
>> + };
>> +
>> + tcsr_mutex: hwlock@1f40000 {
>> + compatible = "qcom,tcsr-mutex";
>> + reg = <0x0 0x1f40000 0x0 0x20000>;
>> + #hwlock-cells = <1>;
>> + };
>> +
>> + pdc: interrupt-controller@b220000 {
>> + compatible = "qcom,qdu1000-pdc", "qcom,pdc";
>> + reg = <0x0 0xb220000 0x0 0x30000>, <0x0 0x174000f0 0x0 0x64>;
>> + qcom,pdc-ranges = <0 480 12>, <14 494 24>, <40 520 54>,
>> + <94 609 31>, <125 63 1>;
>> + #interrupt-cells = <2>;
>> + interrupt-parent = <&intc>;
>> + interrupt-controller;
>> + };
>> +
>> + spmi_bus: spmi@c400000 {
>> + compatible = "qcom,spmi-pmic-arb";
>> + reg = <0x0 0xc400000 0x0 0x3000>,
>> + <0x0 0xc500000 0x0 0x400000>,
>> + <0x0 0xc440000 0x0 0x80000>,
>> + <0x0 0xc4c0000 0x0 0x10000>,
>> + <0x0 0xc42d000 0x0 0x4000>;
>> + reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
>> + interrupt-names = "periph_irq";
>> + interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
>> + qcom,ee = <0>;
>> + qcom,channel = <0>;
>> + #address-cells = <2>;
>> + #size-cells = <0>;
>> + interrupt-controller;
>> + #interrupt-cells = <4>;
>> + };
>> +
>> + tlmm: pinctrl@f000000 {
>> + compatible = "qcom,qdu1000-tlmm";
>> + reg = <0x0 0xf000000 0x0 0x1000000>;
>> + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
>> + gpio-controller;
>> + #gpio-cells = <2>;
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> + gpio-ranges = <&tlmm 0 0 151>;
>> + wakeup-parent = <&pdc>;
>> +
>> + qup_uart0_default: qup-uart0-default-state {
>> + pins = "gpio6", "gpio7", "gpio8", "gpio9";
>> + function = "qup00";
>> + };
>> +
>> + qup_i2c1_data_clk: qup-i2c1-data-clk-state {
>> + pins = "gpio10", "gpio11";
>> + function = "qup01";
>> + };
>> +
>> + qup_spi1_data_clk: qup-spi1-data-clk-state {
>> + pins = "gpio10", "gpio11", "gpio12";
>> + function = "qup01";
>> + };
>> +
>> + qup_spi1_cs: qup-spi1-cs-state {
>> + pins = "gpio13";
>> + function = "gpio";
>> + };
>> +
>> + qup_i2c2_data_clk: qup-i2c2-data-clk-state {
>> + pins = "gpio12", "gpio13";
>> + function = "qup02";
>> + };
>> +
>> + qup_spi2_data_clk: qup-spi2-data-clk-state {
>> + pins = "gpio12", "gpio13", "gpio10";
>> + function = "qup02";
>> + };
>> +
>> + qup_spi2_cs: qup-spi2-cs-state {
>> + pins = "gpio11";
>> + function = "gpio";
>> + };
>> +
>> + qup_i2c3_data_clk: qup-i2c3-data-clk-state {
>> + pins = "gpio14", "gpio15";
>> + function = "qup03";
>> + };
>> +
>> + qup_spi3_data_clk: qup-spi3-data-clk-state {
>> + pins = "gpio14", "gpio15", "gpio16";
>> + function = "qup03";
>> + };
>> +
>> + qup_spi3_cs: qup-spi3-cs-state {
>> + pins = "gpio17";
>> + function = "gpio";
>> + };
>> +
>> + qup_i2c4_data_clk: qup-i2c4-data-clk-state {
>> + pins = "gpio16", "gpio17";
>> + function = "qup04";
>> + };
>> +
>> + qup_spi4_data_clk: qup-spi4-data-clk-state {
>> + pins = "gpio16", "gpio17", "gpio14";
>> + function = "qup04";
>> + };
>> +
>> + qup_spi4_cs: qup-spi4-cs-state {
>> + pins = "gpio15";
>> + function = "gpio";
>> + };
>> +
>> + qup_i2c5_data_clk: qup-i2c5-data-clk-state {
>> + pins = "gpio130", "gpio131";
>> + function = "qup05";
>> + };
>> +
>> + qup_spi5_data_clk: qup-spi5-data-clk-state {
>> + pins = "gpio130", "gpio131", "gpio132";
>> + function = "qup05";
>> + };
>> +
>> + qup_spi5_cs: qup-spi5-cs-state {
>> + pins = "gpio133";
>> + function = "gpio";
>> + };
>> +
>> + qup_i2c6_data_clk: qup-i2c6-data-clk-state {
>> + pins = "gpio132", "gpio133";
>> + function = "qup06";
>> + };
>> +
>> + qup_spi6_data_clk: qup-spi6-data-clk-state {
>> + pins = "gpio132", "gpio133", "gpio130";
>> + function = "qup06";
>> + };
>> +
>> + qup_spi6_cs: qup-spi6-cs-state {
>> + pins = "gpio131";
>> + function = "gpio";
>> + };
>> +
>> + qup_uart7_rx: qup-uart7-rx-state {
>> + pins = "gpio135";
>> + function = "qup07";
>> + };
>> +
>> + qup_uart7_tx: qup-uart7-tx-state {
>> + pins = "gpio134";
>> + function = "qup07";
>> + };
>> +
>> + qup_uart8_default: qup-uart8-default-state {
>> + pins = "gpio18", "gpio19", "gpio20", "gpio21";
>> + function = "qup10";
>> + };
>> +
>> + qup_i2c9_data_clk: qup-i2c9-data-clk-state {
>> + pins = "gpio22", "gpio23";
>> + function = "qup11";
>> + };
>> +
>> + qup_spi9_data_clk: qup-spi9-data-clk-state {
>> + pins = "gpio22", "gpio23", "gpio24";
>> + function = "qup11";
>> + };
>> +
>> + qup_spi9_cs: qup-spi9-cs-state {
>> + pins = "gpio25";
>> + function = "gpio";
>> + };
>> +
>> + qup_i2c10_data_clk: qup-i2c10-data-clk-state {
>> + pins = "gpio24", "gpio25";
>> + function = "qup12";
>> + };
>> +
>> + qup_spi10_data_clk: qup-spi10-data-clk-state {
>> + pins = "gpio24", "gpio25", "gpio22";
>> + function = "qup12";
>> + };
>> +
>> + qup_spi10_cs: qup-spi10-cs-state {
>> + pins = "gpio23";
>> + function = "gpio";
>> + };
>> +
>> + qup_i2c11_data_clk: qup-i2c11-data-clk-state {
>> + pins = "gpio26", "gpio27";
>> + function = "qup13";
>> + };
>> +
>> + qup_spi11_data_clk: qup-spi11-data-clk-state {
>> + pins = "gpio26", "gpio27", "gpio28";
>> + function = "qup13";
>> + };
>> +
>> + qup_spi11_cs: qup-spi11-cs-state {
>> + pins = "gpio29";
>> + function = "gpio";
>> + };
>> +
>> + qup_i2c12_data_clk: qup-i2c12-data-clk-state {
>> + pins = "gpio28", "gpio29";
>> + function = "qup14";
>> + };
>> +
>> + qup_spi12_data_clk: qup-spi12-data-clk-state {
>> + pins = "gpio28", "gpio29", "gpio26";
>> + function = "qup14";
>> + };
>> +
>> + qup_spi12_cs: qup-spi12-cs-state {
>> + pins = "gpio27";
>> + function = "gpio";
>> + };
>> +
>> + qup_i2c13_data_clk: qup-i2c13-data-clk-state {
>> + pins = "gpio30", "gpio31";
>> + function = "qup15";
>> + };
>> +
>> + qup_spi13_data_clk: qup-spi13-data-clk-state {
>> + pins = "gpio30", "gpio31", "gpio32";
>> + function = "qup15";
>> + };
>> +
>> + qup_spi13_cs: qup-spi13-cs-state {
>> + pins = "gpio33";
>> + function = "gpio";
>> + };
>> +
>> + qup_uart13_default: qup-uart13-default-state {
>> + pins = "gpio30", "gpio31", "gpio32", "gpio33";
>> + function = "qup15";
>> + };
>> +
>> + qup_i2c14_data_clk: qup-i2c14-data-clk-state {
>> + pins = "gpio34", "gpio35";
>> + function = "qup16";
>> + };
>> +
>> + qup_spi14_data_clk: qup-spi14-data-clk-state {
>> + pins = "gpio34", "gpio35", "gpio36";
>> + function = "qup16";
>> + };
>> +
>> + qup_spi14_cs: qup-spi14-cs-state {
>> + pins = "gpio37", "gpio38";
>> + function = "gpio";
>> + };
>> +
>> + qup_i2c15_data_clk: qup-i2c15-data-clk-state {
>> + pins = "gpio40", "gpio41";
>> + function = "qup17";
>> + };
>> +
>> + qup_spi15_data_clk: qup-spi15-data-clk-state {
>> + pins = "gpio40", "gpio41", "gpio30";
>> + function = "qup17";
>> + };
>> +
>> + qup_spi15_cs: qup-spi15-cs-state {
>> + pins = "gpio31";
>> + function = "gpio";
>> + };
>> + };
>> +
>> + apps_smmu: iommu@15000000 {
>> + compatible = "qcom,qdu1000-smmu-500", "arm,mmu-500";
>> + reg = <0x0 0x15000000 0x0 0x100000>;
>> + #iommu-cells = <2>;
>> + #global-interrupts = <2>;
>> + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
> There should be a space, not a tab after the = sign.
Sure.
>
>
>> + <GIC_SPI 426 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 671 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 672 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>;
>> + };
>> +
>> + intc: interrupt-controller@17200000 {
>> + compatible = "arm,gic-v3";
>> + reg = <0x0 0x17200000 0x0 0x10000>, /* GICD */
>> + <0x0 0x17260000 0x0 0x80000>; /* GICR * 4 */
>> + #interrupt-cells = <3>;
>> + interrupt-controller;
>> + #redistributor-regions = <1>;
>> + redistributor-stride = <0x0 0x20000>;
>> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
> Please move interrupts below reg.
Ok.
>
>> + };
>> +
>> + timer@17420000 {
>> + compatible = "arm,armv7-timer-mem";
>> + reg = <0x0 0x17420000 0x0 0x1000>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + frame@17421000 {
>> + reg = <0x17421000 0x1000>,
>> + <0x17422000 0x1000>;
>> + frame-number = <0>;
>> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
> Please move interrupts above frame-number.
Ok.
>
>> + };
>> +
>> + frame@17423000 {
>> + reg = <0x17423000 0x1000>;
>> + frame-number = <1>;
>> + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
>> + status = "disabled";
>> + };
>> +
>> + frame@17425000 {
>> + reg = <0x17425000 0x1000>,
>> + <0x17426000 0x1000>;
>> + frame-number = <2>;
>> + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
>> + status = "disabled";
>> + };
>> +
>> + frame@17427000 {
>> + reg = <0x17427000 0x1000>;
>> + frame-number = <3>;
>> + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
>> + status = "disabled";
>> + };
>> +
>> + frame@17429000 {
>> + reg = <0x17429000 0x1000>;
>> + frame-number = <4>;
>> + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
>> + status = "disabled";
>> + };
>> +
>> + frame@1742b000 {
>> + reg = <0x1742b000 0x1000>;
>> + frame-number = <5>;
>> + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
>> + status = "disabled";
>> + };
>> +
>> + frame@1742d000 {
>> + reg = <0x1742d000 0x1000>;
>> + frame-number = <6>;
>> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + apps_rsc: rsc@17a00000 {
>> + compatible = "qcom,rpmh-rsc";
>> + reg = <0x0 0x17a00000 0x0 0x10000>,
>> + <0x0 0x17a10000 0x0 0x10000>,
>> + <0x0 0x17a20000 0x0 0x10000>;
>> + reg-names = "drv-0", "drv-1", "drv-2";
>> + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
>> + qcom,tcs-offset = <0xd00>;
>> + qcom,drv-id = <2>;
>> + qcom,tcs-config = <ACTIVE_TCS 2>, <SLEEP_TCS 3>,
>> + <WAKE_TCS 3>, <CONTROL_TCS 0>;
>> + label = "apps_rsc";
>> +
>> + apps_bcm_voter: bcm-voter {
>> + compatible = "qcom,bcm-voter";
>> + };
>> +
>> + rpmhcc: clock-controller {
>> + compatible = "qcom,qdu1000-rpmh-clk";
>> + #clock-cells = <1>;
>> + clock-names = "xo";
>> + clocks = <&xo_board>;
> Please keep XYZ-names after XYZ.
Ok.
>
>> + };
>> +
>> + rpmhpd: power-controller {
>> + compatible = "qcom,qdu1000-rpmhpd";
>> + #power-domain-cells = <1>;
>> + operating-points-v2 = <&rpmhpd_opp_table>;
>> +
>> + rpmhpd_opp_table: opp-table {
>> + compatible = "operating-points-v2";
>> +
>> + rpmhpd_opp_ret: opp1 {
>> + opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
>> + };
>> +
>> + rpmhpd_opp_min_svs: opp2 {
>> + opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
>> + };
>> +
>> + rpmhpd_opp_low_svs: opp3 {
>> + opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
>> + };
>> +
>> + rpmhpd_opp_svs: opp4 {
>> + opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
>> + };
>> +
>> + rpmhpd_opp_svs_l1: opp5 {
>> + opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
>> + };
>> +
>> + rpmhpd_opp_nom: opp6 {
>> + opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
>> + };
>> +
>> + rpmhpd_opp_nom_l1: opp7 {
>> + opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
>> + };
>> +
>> + rpmhpd_opp_nom_l2: opp8 {
>> + opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
>> + };
>> +
>> + rpmhpd_opp_turbo: opp9 {
>> + opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
>> + };
>> +
>> + rpmhpd_opp_turbo_l1: opp10 {
>> + opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
>> + };
>> + };
>> + };
>> + };
>> +
>> + cpufreq_hw: cpufreq@17d90000 {
>> + compatible = "qcom,qdu1000-cpufreq-epss", "qcom,cpufreq-epss";
>> + reg = <0x0 0x17d90000 0x0 0x1000>, <0x0 0x17d91000 0x0 0x1000>;
>> + reg-names = "freq-domain0", "freq-domain1";
>> + clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>;
>> + clock-names = "xo", "alternate";
>> + #freq-domain-cells = <1>;
>> + };
>> +
>> + gem_noc: interconnect@19100000 {
>> + compatible = "qcom,qdu1000-gem-noc";
>> + reg = <0x0 0x19100000 0x0 0xB8080>;
>> + #interconnect-cells = <2>;
>> + qcom,bcm-voters = <&apps_bcm_voter>;
> It would be nice to keep #interconnect-cells last.
Sure.
>
>> + };
>> + };
>> +
>> + arch_timer: timer {
>> + compatible = "arm,armv8-timer";
>> + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>> + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>> + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>> + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>> + <GIC_PPI 12 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
>> + clock-frequency = <19200000>;
> Please remove this property, unless this platform is super
> special and doesn't boot without it (otherwise CNTRFRQ_ELn
> is almost surely initialized somewhere earlier in the boot
> chain.
Sure thing.
Thanks,
Melody
>
>
> Konrad
>> + };
>> +};
>> diff --git a/arch/arm64/boot/dts/qcom/qru1000.dtsi b/arch/arm64/boot/dts/qcom/qru1000.dtsi
>> new file mode 100644
>> index 000000000000..eac5dc54a8ab
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/qcom/qru1000.dtsi
>> @@ -0,0 +1,26 @@
>> +// SPDX-License-Identifier: BSD-3-Clause
>> +/*
>> + * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved.
>> + */
>> +
>> +#include "qdu1000.dtsi"
>> +/delete-node/ &tenx_mem;
>> +/delete-node/ &oem_tenx_mem;
>> +/delete-node/ &tenx_q6_buffer_mem;
>> +
>> +&reserved_memory {
>> + oem_tenx_mem: oem-tenx@a0000000 {
>> + reg = <0x0 0xa0000000 0x0 0x6400000>;
>> + no-map;
>> + };
>> +
>> + mpss_diag_buffer_mem: mpss-diag-buffer@aea00000 {
>> + reg = <0x0 0xaea00000 0x0 0x6400000>;
>> + no-map;
>> + };
>> +
>> + tenx_q6_buffer_mem: tenx-q6-buffer@b4e00000 {
>> + reg = <0x0 0xb4e00000 0x0 0x3200000>;
>> + no-map;
>> + };
>> +};
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2022-12-20 18:57 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-12-16 23:27 [PATCH v5 0/2] Add base device tree files for QDU1000/QRU1000 Melody Olvera
2022-12-16 23:27 ` [PATCH v5 1/2] arm64: dts: qcom: Add base QDU1000/QRU1000 DTSIs Melody Olvera
2022-12-17 14:59 ` Konrad Dybcio
2022-12-20 18:56 ` Melody Olvera
2022-12-16 23:27 ` [PATCH v5 2/2] arm64: dts: qcom: Add base QDU1000/QRU1000 IDP DTs Melody Olvera
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).